JD 4720 Front 3 Point Owners Manual

Transcription

Owners Manual
JD 4120, 4320,
4520, 4720
Sub Frame
Kage InnovationTM LLC
2155 Woodlane Dr. Suite 200 Woodbury, MN 55125
kageinnovation.com
(651) 433 – 4628
JD 4720 Undercarriage
JSK-4700
Version#
15
4
10
12
6
16
15
2
13
5
9
11
7
8
6
14
10
12
3
4
8
7
11
Copyright Kage Innovation All Rights Reserved
1
www.kageinnovation.com
8
651 433 4628
7
11
1
Item Part Name
Part Number
Qty
1
2
3
4
5
Hex Bolt GR5 1/2 - 13 x 1.75
Bumper
Hose Hoop Bracket
Hex Nut GR5 5/8-11
Socket Head Screw 5_16-18 x .625
92865A718
9306K69
K456-1
95462A533
90128A580
5
1
1
10
2
6
7
8
9
10
Hex Bolt GR5 5/8-11 x 2.25
Split Lockwasher, 1/2
Hex Nut, 1/2 - 13
Hex Bolt GR5 1/2-13 x 2.5
Flat Washer 5/8
92865A803
ROC-8076-033
ROC-4181-033
91247A722
90126A035
10
13
13
8
20
11
12
13
14
15
Flat Washer 1/2
Lockwasher 5/8
Curtain Brace
JD 4720 Side Frame Pass
JD 4720 Side Frame Driver
ROC-8071-033
91102A035
47-30
47-20
47-10
26
10
1
1
1
16
JD 4720 Front Mount
47-40
1
4720 Standard Hydraulic Group
KTM47-JD
Version#
11
4
2
5
6
3
1
Copyright Kage Innovation All Rights Reserved
www.kageinnovation.com
651 433 4628
Item
Part Name
Part Number Quantity
1
2
3
4
5
Male Ag Coupler
Lift cylinder
Hydro Line, Driver
Male JIC x Male NPTF
Lynch Pin 3_16
19-400
PMC-5416
HY-708
2404-08-06
90170A650
6
Hitch Pin
BP 075 0500 2
4
1
4
2
2
John Deere® 4720 Series Sub Frame Installation Instructions
INTRODUCTION:
The Kage Sub Frame kit for John Deere® 4120, 4320, 4520, and 4720 Series fits only those
tractor models.
---------------------------------------------------------------------------------------------------------------------
Kage Innovation LLC | 2155 Woodlane Dr. Suite 200 | Woodbury 55125
Tel. (651) 433-4628 | Fax (651) 207 6342 | www.kageinnovation.com | [email protected]
STEP 1:
Install the JD 4720 Front Mount
onto the front of the tractor frame.
Loosely fasten with three 1/2 – 13
x 1 3/4” bolts and hardware. Use
floor jacks for positioning if
necessary.
STEP 2:
Position the Driver and Passenger Side Frames underneath the front axle. Loosely install one
5/8 – 11 x 2 1/4” bolt and corresponding washers, lock washer and nut into the rear hole of each
Side Frame. The rear of the Side Frames must mount on the inside of the tractor frame. Use floor
jacks for positioning.
STEP 3:
Use a pry bar or large screwdriver to position the Side Frames and fasten them to the sides of the
Front Mount. Loosely install four 1/2 - 13 x 2 1/2” bolts with hardware.
STEP 4:
Install the Curtain Brace to the Side Frames with six 5/8 – 11 x 2 1/4” bolts and hardware. Install
the remaining 5/8 – 11 x 2 1/4” bolts and hardware to the rear of each Side Frame.
STEP 5:
Install the Hose Hoop Bracket on
the Passenger Side Frame using
two 1/2 – 13 x 1 3/4” bolts and
hardware.
STEP 6:
Install the Bumper to the Front
Mount with two 5/16 – 18 x 5/8”
socket head cap screws. This takes
a 1/4” hex key.
STEP 7:
Tighten all loose bolts and nuts.
STEP 8:
1: Plumb the Lift Cylinder with two
1/2” Male JIC x 3/8” Male NPTF
fittings. Use TFE paste on pipe
thread.
2: Hang the Lift Cylinder on the
Front Mount using the Hitch Pin,
with ports facing towards the
tractor.
STEP 9:
1: Install two “Hydro Line, Driver” hose assemblies at the top and bottom of the “Lift Cylinder.”
2: Route “Hydro Line, Driver” hose assemblies underneath tractor frame, than up through the
Hose Hoop Bracket.
3: Install Male Ag couplers on “Hydro Line, Driver” hose assemblies. Plug them into the mid
hydraulic ports Female Ag couplers, orientated closest to the tractor.
4: Tighten all loose hydraulic fittings.
NEXT: Attaching the Kage Blade SnowFire System
STEP 1:
1: Install two “Hydro Line, Driver” hose assemblies onto the Crossover Relief Valve.
2: Install a Restrictor on one “Hydro Line, Driver” hose assembly, than a Male Ag Coupler onto
each hose assembly. Use TFE paste on pipe thread.
3: Install two 1/4” JIC Elbows onto the 1/4” JIC Bulkhead fittings. Loosen the Beta Clamp and
install two “Line, Dist Block to Bulkhead LG” hose assemblies onto the 1/4” JIC Elbows.
4: Install two 1/4” Male JIC x 1/2” Male NPTF 90 Elbow fittings onto “Line, Dist Block to
Bulkhead LG” hose assemblies. Install two Male Ag Couplers onto 1/4” Male JIC x 1/2” Male
NPTF 90 Elbow. Use TFE paste on pipe thread.
5: Tighten Beta Clamp and all loose hydraulic fittings.
STEP 2:
Place a 2x4 board under plow pivot
frame. This will give you the
elevation needed for a quick attach.
Lay the plow hydraulic lines over
the front of the plow to keep them
out of the way.
STEP 3:
Pull up the tractor until the Side Frame bushings are just above the plows Locking Pins. Enable
float for the hydraulic system, by pushing the joystick forward with the engine off. Manually
extend the Lift Cylinder to the plow pivot frame and insert the Hitch Pin.
STEP 4:
1: Route two “Hydro Line, Driver” hose assemblies over the front plate of the JD 4720 Front
Mount, under the tractor frame, through the Hose Hoop Bracket and into the tractors remaining
two mid hydraulic ports.
2: Route two “Line, Dist Block to Bulkhead LG” hose assemblies through the Hose Hoop
Bracket, over the tractors rear axle and into the hydraulic ports in the rear of the tractor. Secure if
needed with zip ties.
STEP 5:
1: Disable float for the hydraulic system by moving the joystick back to its normal position. Pull
out and latch both Locking Pins.
2: Slowly retract the Lift Cylinder to raise the plow’s pivot frame. Unlatch the Locking Pins once
they can bottom out on the Side Frames.
3: Continue to raise the pivot frame and the Locking Pins will snap into the Side Frame bushings
at this point. This plate and tubing act as a guide. As long as they are touching, all you have to
control is the height of the pivot frame, in order to achieve a guided latching process.
Kage Limited Warranty
Kage Innovation will repair or, at the option of Kage Innovation, replace those parts
which prove defective due to material or workmanship under normal use for a period of
two (2) years from the date of retail sale or date of invoice from Kage Innovation,
whichever is later. Expendable items, such as rubber, or polyurethane are excluded from
this warranty.
Kage Innovation warrants that the products manufactured by us to be in accordance with
our published specifications or those specifications agreed to by us in writing at the time
of sale. The obligation of Kage Innovation is expressly limited to repairing or replacing,
at its option, any product not meeting such specifications within the warranty period.
LIMITATIONS OF WARRANTY AND DAMAGES
KAGE INNOVATION MAKES NO OTHER WARRANTY, EXPRESSED OR
IMPLIED, AND MAKES NO WARRANTY OF MERCHANTABILITY OR OF
FITNESS FOR ANY PARTICULAR PURPOSE. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE FACE HEREOF.
IN NO EVENT SHALL KAGE INNOVATION, BE HELD LIABLE FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR DAMAGES
RESULTING FROM MISAPPLICATION, ABUSE, MISUSE, ACTS OF GOD,
UNAUTHORIZED ALTERATION OF THE KAGE INNOVATION PRODUCT, OR
SUBSTITUTION OF PARTS NOT AUTHORIZED IN WRITING BY KAGE
INNOVATION.
To obtain service under this warranty the consumer must return the defective Kage
Innovation product to Kage Innovation directly, the dealer from which the product was
purchased or to any authorized Kage Innovation dealer, transportation and freight charges
prepaid. Only Kage Innovation dealers are authorized to perform the obligations under
this warranty with pre-authorization from Kage Innovation.
No person is authorized to alter or amend this warranty or to create any warranty other
than that set forth herein without the expressed written consent of Kage Innovation.
Kage Innovation reserves the right to make improvement changes on any of our products
without prior notice.

JD 4720 Front 3 Point Owners Manual

Transcription

Similar documents

PDF Assembly Instructions Now-Click Here - Port-A-Wall

Napa Unicoil sellsheet Dealer copy.indd

GOLDENHORN 12S

UNICOIL Hose Bender Flyer

TSB 33

Novaflex®

HB 125 HYDRAULIC CHAIN TENSIONER INSTRUCTIONS

100 cwflx - Kanaflex

where quality and price meet head-on

Brochure - coolshirt systems