Full 2015 / 2016 Amperes Catalogue

Transcription

15
th
Year Of Excellence
amperes
Precision Design, Absolute Confidence
PUBLIC ADDRESS SYSTEM
C O M M E R C I A L I N S TA L L AT I O N S
20
15
16
ISO 9001: 2008
Design & Manufacture of Public Address Equipment and Systems
Certificate No. 16895 / A / 0001 / UK / En
AMPERES ELECTRONICS SDN BHD (Co No. 509025-X)
Organisation
Reaching Out
Amperes Electronics is now in its 15th years and shall continue to grow for the next
few decades. It was started as a sole proprietor and with the promising future, it was
incorporated into a Private Limited company ( Sdn Bhd ) in the year 2000. Puchong,
a fast growing township near Kuala Lumpur has been the base of operation and for
its future expansion.
Amperes has been a name synonymous with Public
Address Systems. With thousands of references in the
region, it is no doubt that Amperes is a brand well
accepted. We sincerely express our heartfelt thanks to our
loyal clients in our home ground as well as our partners in
South East Asia and Middle East countries.
We began from a tiny premises and our
persistence in pursuing the goal had made the
company to grow steadily. From a small
workbench, we focus on the mission and can
proudly to claim that we are a true entity
involved in Research and Development,
manufacturing
and
distribution.
With
dynamism of growth, our production floor has
expanded to many folds since its inception.
15
In order to be a part of institution, we are members of Federation of Malaysian
Manufacturer ( FMM ) and Matrade, with " amperes " registered as our trademark.
Product
th
Forward
We started from fabricating customised
accessories of AV market such as patch panels,
selectors, etc. Due to acceptance of our quality
workmanship, more and more complicated
products were required and hence, it was the
opportunity came knocking.
As the path ahead never gets easier, Amperes shall
endeavour to sail through, producing more technologically advanced and cost effective products for every
stake holders.
Year Of
Excellence
Standardised products should be the way to go, thereby ZS601 ; 6 channel speaker
zone selector were the first product introduced.
We listen and react, seek and apply the shared
knowledge to achieve a brand name of
“ Precision Design, Absolute Confidence “.
From there on, more and more products were developed, based on the requirement of
clients and in accordance to British Standards. What we truly emphasise are the
suitability of installations, user friendly and keeping the cost at optimum level.
Currently, we are able to provide solutions from simple and basic installations to mid and
large scale setups. As PA technology advances, we join the race in IP technology.
Integrating conventional systems with Ethernet based products. As IP Systems shall be
the game in future, Amperes shall invest substantially in developing items in this field.
Philosophy & Mission
Continuous Product Development policy is the heart of producing excellent and reliable
products and is the vital route of placing Amperes in arena of global players. Major
portion of revenue is invested in R and D, not only developing new equipment but
enhancing present models.
Since the certification of ISO9001 : 2008, Amperes had
been emphasising the best practices in its management of product and operation, in the goal to achieve a
well respected organisation.
A Member Of :
Fed of Malaysian Manufacturer (FMM)
Design & Manufacturing of
Public Address Equipment
An organisation without a mission is a meaningless
journey to travel, and Amperes adopts a simple one :
“ Adopting the best organisation practices
where possible, producing products of
contemporary needs and cost effective yet
reliable. “
ISO 9001: 2008
www.ampereselectronics.com
catalogue 2015 : all rights reserved by amperes electronics sdn bhd
1
Introduction
iPX5101
iPX5200
iPX5151
iPX5300
iPX5500
2
IP BASED PA SOLUTION
IP Based System
Ethernet Paging Server
Ethernet Music Server
Ethernet Paging Client
Ethernet Music Client
Ethernet Comm. Box
PD1240
PD1280
PD2400
PD2800
PD1160
PM1000
PM1060
PM1120
EP1200A
4
CM1400
MICS
CD1001
MP1020
MR1301
PT1801
FI6000
5
MxP2188
MxP2188
MxP2288
Tech. Info
DA2208
MX2222
6
PA300S
QP2000S
PA2000S
DP2000S
MA2000S
MC2000S
Tech. Info
10
11
12
PAGING MICROPHONE
Digital Paging Microphone (Soft Touch Buttons)
24 Zone Digital Paging Microphone (Soft Touch Buttons)
24 Zone Digital Paging Microphone
Digital Paging Microphone
8/16 Zone Remote Paging Microphone
Desktop Paging Microphone
6 Ch Desktop Paging Microphone
12 Ch Desktop Paging Microphone
Emergency Paging Microphone Panel
13
13
14
14
14
15
15
15
16
17
17
18
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
12 Ch Speaker Zone Selector
6 Ch Uninterrupted Paging Speaker Zone Selector
Source Selector
8 Ch Decoder / Zone Selector
24 Ch Data Decoder
9
POWER SUPPLIES & DISTRIBUTION
BC9740
SQ9715
PS9400
24V DC Automatic Battery Charger
Sequential Power Switcher
Regulated 24V DC Power Supply
39
39
40
40
41
41
42
43
44
45
45
VOLUME CONTROLLER / PATCH
6 Zone Rack Mounted Volume Controllers
Auto Volume Controller
5 / 10 / 30 / 50 / 100 / 150W Volume Controllers
5 / 10 / 30 / 50 / 100W Volume Controllers
Speaker Patch Panel
100V - 8 Ohm Speaker Patch Panel
VR7600S
AV7200
VC7000S
VC8000S
VP7501
VP7810
46
46
47
47
48
48
SPEAKERS
CS Series
CS620 / 840
BS / DV410
FS Series
CL / CH Series
PS / GS
SP Series
HS Speaker
Accessories
Tech. info
Tech. Info
35
35
36
37
38
38
SELECTORS & DATA DECODER
ZS5122
ZS5062
ZS5121
ZS5601
ZS5602
SS6401
TD6080
TD6240
12
POWER AMPLIFIERS
10 / 20 /30W Mini Amplifiers
125 /250 / 375 / 500W Power Amplifiers with AFS
120 / 240 / 360 / 480W Power Amplifiers
Multichannel Power Amplifier
60 / 120W Mixer Amplifier with Zone Selection
60 / 120W Basic Mixer Amplifiers
Sound Pressure Level
6 Duty / 1 Standby Amplifier Changeover Panel
6 Duty / 1 Standby Manual Changeover Panel
8 Duty / 1 Standby Auto Standby Amplifier Fault Changeover
6 Channel Speaker Line Surveillance
Amplifier Surveillance Module
12 Channel Amplifier Monitor Panel
11
MIXERS / DISTRIBUTION
8 x 8 Matrix Paging Controller
8 x 8 Matrix Paging Controller (System Components)
8 x 8 Matrix Paging Controller (Preview)
General Terms
2 Input 8 Output Signal Distribution Amplifier
Pre-Amplifier Mixer
AX700
AC3601
AX3800
LS4600
AS4000
AM4120
10
INPUTS
Chime & Siren Tone Generator
Microphones
CD/MP3/AM-FM Tuner
2 Ch Media Player
Message Recorder / Player
Weekly Programmable Timer
Fire Alarm Interface
AMPLIFIER CHANGEOVER & MONITORING
8
SOFTWARE BASED PA SYSTEM
PMX II
Standard Music Server Software
PMX II LAN LAN Based Music Server w. Monitoring
Tech. Info
Product Selection Guide
3
04
06
07
08
08
09
7
Dual Cone Ceiling Speaker
Co-axial Ceiling Speaker
Surface Mount Speakers
Full Range Speakers
Column Speakers
Pendant Ball / Ground Speakers
Projection Speakers
Horn Speaker
49
50
51
52
53
54
55
56
OTHERS
Complimentary products
Guide to Ceiling Speakers Installation
Calculating Battery Capacity
57
58
59
iPX5000 Series
amperes
IP Based System
Introduction
IP Based PA System is seeing growth in coming future based on the growing size of
installations, expanding complexity of requirement and cost consciousness in
connecting large scale sites. Cabling infrastructure can be simplified and reduced and
among the important features is the ability for IP system to cater for future
expansions without having to relay cables.
Amperes iPX5000 offers solution to convert conventional system into IP environment
with ease. With continuous development of IP related products, iPX shall not only
provide seamless connectivity between systems but would be able to provide real
time monitoring and controls with the new Amperes PMX II LAN software.
DECENTRALISED
PAGING SYSTEM
EQUIPMENT
MONITORING
& CONTROLS
IP SOLUTIONS
VOICE & EVAC
ANNOUNCEMENT
TO PA SYSTEM
BGM DISTRIBUTIONS
Features and Advantages of iPX5000 Series
101010
DUPLEX DIGITAL AUDIO TRANSMISSION
DECENTRALIZED SYSTEM
Audio signal is transmitted in digital format thereby provides immunity
from noise which would normally occur using analogue signal for long
distance transmission.
Building to building inter connectivity shall be further simplified by using
existing IT network whereas in conventional system, a substantial
amount of copper cable has to be laid to link to main rack.
CHOICE OF CONNECTIVITY
EXPANSION & CONVERSION
Communications between main paging station to remote can be
achieved using local LAN or WAN, Internet or using Fiber Optic Cable
(converter required).
System can be expanded further to cater for larger area without having
to run connecting cablings to the main rack, provided there is a network
point in the new location.
COST SAVINGS
MOBILITY
Significant cost savings on cabling works can be achieved by applying
IP, especially in large setup such as university, factory and office
complexes.
With readily available Wifi, the BGM broadcast CPU can be placed
anywhere, thus eliminating the limitations of using wired system.
REMOTE CONTROLS / MONITORING
4
MULTI LEVEL SYSTEM ACCESS
As long as there is a LAN connectivity, paging to remote connection
shall be achievable. Among applications include paging to train
stations, branch offices or factories.
Access to the system operation or setup can be tiered according to
different levels via the management software (Available soon). This
shall prevent unnecessary interference to the system.source can be
broadcasted in the entire setup.
MULTIPLE AUDIO BROADCAST
INTEGRATION
Multiple BGM source can be broadcasted to entire system with each
receiving point having flexibility to select the preferred music source.
This flexibility shall not be available in conventional system where only
a single source can be broadcasted in the entire setup.
iPX5000 series can be easily integrated with existing Amperes
products such as MatriMix Paging, PMX or PD Series of Paging
Microphones.
iPX5000 Series
amperes
IP Based System
Application in Multi Location Setup
Sub Building
Network
Switch
Sub Building
Network
Switch
iPX5300
iPX5300
iPX5151
Music
iPX5151
Paging
Music
Paging
PD Mic
PD Mic
iPX5151
iPX5151
Local PA System
Local PA
PA System
Interconnections between Sub Systems via LAN / Fiber Optic
iPX5151
Network Switch
iPX5101
iPX5151
iPX5300
Local PA System
PD Mic
PC WITH PMX II
LAN SOFTWARE
iPX5200
Main Building
(Main System)
MP3 CD
TUNER
Linking multiple locations via Ethernet / LAN allows full controls, cost savings and flexibility in which conventional installations would not be possible. Should cable link to sub system
not possible, wireless connections using IP transceiver shall be the option.
The main system shall be able to page to desired zone of any of the remote sub system and vice versa. Each system shall work independently regardless of communication continuity with the main rack, thereby reducing communication risk during downtime.
Components in IP Paging
IP Network Controller
IP Music Server
IP Communication Box
Amperes IP System has been upgraded from its
first model and iPX5101 succeeded iPX5100 as
the Paging Server or Ethernet Paging Controller.
In this version, more clients within a system are
allowed and not limited as previously.
iPX5200 offers a great way of streaming audio to remote
locations via LAN, delivering high quality sound
reproduction at the receiving end. It is also known as
Network Audio Inserter, enabling analogue audio from
players to be fed into the IP network.
iPX5500 is used to relay information from various equipments
with RS485 and to transmit to PC via Ethernet. Amperes PMX
II LAN software with monitoring modules shall be used to
monitor or control the remote equipment.
IP Paging Client
IP Music Client
PMX II LAN Software
iPX5151 is the Ethernet Paging Client which
receives and transmits paging audio and RS486
data from digital paging microphone, which is then
fed to PA mixer for amplification.
iPX5300, Ethernet Music Client is used to receive audio
streaming from central rack either from iPX5200
Ethernet Music Server or via PMX II LAN. Quality sound
can be expected as it plays MP3 audio at up to 320
kbps.
PMX II V2 is the latest version released, rendering greater
flexibility in operating and loaded with extra features including
the ease of interfacing with external paging microphones.
5
iPX5101
Ethernet Paging Server
IP Based System
amperes
Introduction
Technical Specifications
Amperes IP System has been upgraded from its first model and iPX5101 succeeded
iPX5100 as the Paging Server or Ethernet Paging Controller. In this version, more
clients within a system are allowed and not limited as previously. Multicast method is
employed, and apart from the number of client, the other main advantage is the
transmission speed. Progressive delay in receiving audio and data from Paging Mic
are eliminated and every client shall receive the transmission simultaneously.
Power requirement :
Voltage
Current
18 ~ 24V DC (Normal DC 24V)
350 mA
Connectivity
- LAN interface
- Common protocols
- Priority protocols
RJ-45, 100Mb/s
TCP/IP, UDP, IGMP, HTTP
UDMP, ADP
IPX5101 functions as the traffic controller for all paging clients ( iPX5151 ). Every
activity from Clients shall be assessed by the Controller and shall route the transmission to its intended destination. It is used to store various parameters of clients
connected to it such as priority level, zone configuration, routing destination, etc.
Audio
- Analogue input (peak-to-peak)
- Input load resistance
- Input load capacitance
- Total harmonic distortion (THD)
- S/N ratio (full scale signal)
- Digital format
Integration with iPX5151 shall form a complete IP solution to enable paging via
Ethernet. Setup process had been made simpler and all are performed via http.
Rear View:
Firmware upgrade
255 Max
(Web Browser) IE V8+, Firefox V22+, Google
Crome V25+, RS485
Via Web Browser
Operating condition :
Temperature
Humidity
-20°C ~ 80°C
80%
Case :
Dimension
Weight
482 x 44 x 180 mm
1.9 kg
Client connection
User interface
Packing information
Qty per carton : 1 unit
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.9 kg
1.25Vrms
30 Ohm
100 pF
0.1%
83 dB
IMA ADPCM / MP3 (CBR / 320 kbps max) /
WAV
Application Schematic
PD SERIES
PAGING MIC
amperes
ETHERNET
iPX
ETHER5151
NET
PAGIN
G CLIEN
T
ADDRESS
LINE
BALANCED
OUTPUT
RESET
cat5e / 6 direct or through network
iPX5151
ETHERNET
iPX5151
iPX
amperes
ETHERNET
ETHER 5151
NET
PAGIN
G CLIEN
T
ADDRESS
LINE
iPX
amperes
ETHERNET
ETHER5151
NET
PAGIN
G CLIENT
ADDRESS
BALANCED
OUTPUT
LINE
BALANCED
OUTPUT
RESET
RESET
EP1200A EMER.
PAGING MIC
amperes
ETHERNET
iPX
ETHER5151
NET
PAGIN
G CLIEN
T
ADDRESS
LINE
BALANCED
OUTPUT
RESET
ETHERNET
iPX5151
MR1300 MESS.
PLAYER
iPX5200 MUSIC
SERVER
MP3 / TUNER / CD
MEDIA PLAYER
iPX 5 1 0 1
iPX5300
amperes
ETHERNET
ETHERNET
iPX
ETHER5300
NET
MUSIC
ADDRESS
CLIENT
LINE
BALANCED
OUTPUT
RESET
ETHERNET
music audio
paging audio
& data
LOCAL PA EQUIPMENT
INCL. PRE-AMPLIFIER
MIXER ZONE DECODER
POWER AMPLIFIERS
ETC.
NETWORK SWITCH WITH FIBER LINK
FROM FIRE ALARM
INTERFACE
NETWORK SWITCH WITH FIBER LINK
ETHERNET
iPX5151
iPX5300
amperes
ETHERNET
iPX
ETHER5300
NET
MUSIC
ADDRESS
CLIENT
LINE
BALANCED
OUTPUT
RESET
ETHERNET
music audio
paging audio
& data
LOCAL PA EQUIPMENT
INCL. PRE-AMPLIFIER
MIXER ZONE DECODER
POWER AMPLIFIERS
ETC.
a m pe re s
ACT
STATUS
REM
POWER
iPX5101
IP PAGING CONTROLLER
MAIN SYSTEM
6
Fiber redundant loop ( not available to all switchers )
SUB SYSTEM
iPX5200
Ethernet Music Server
amperes
IP Based System
Introduction
Network Audio
Inserter
SD Card Slot
LAN
Environment
Features
4 analogue line inputs and 1 SD card BGM sources for audio streaming via LAN
Connectivity of up to 255 iPX5300 music clients
Client groupings into 8 for easy broadcast destination selection
Ease of programming / configuration via http page
High quality audio encoding and transmission
iPX5200 offers a great way of streaming audio to remote locations via LAN, delivering
high quality sound reproduction at the receiving end. It is also known as Network Audio
Inserter, enabling analogue audio from players to be fed into the IP network.
With its multiple analogue inputs and SD card reader, user shall be able to select the
channel desired and stream them to individual or group of music clients of their choice.
Eight groups are available, with each group consisting of up to 32 clients.
Setting of various parameters shall be through http, and status of each client can be
directly monitored at real time.
iPX5200 is indeed an outstanding tool for LAN audio streaming at reasonable cost,
suitable for varsities, office buildings, club houses, hotels etc.
Rear View:
DC 24V
ETHERNET ADDRESS :
+ -
Multiformat audio file transmission and decoding
ETHERNET
ON/OFF
Quality Product From
AMPERES ELECTRONICS
LEFT
RESET
IPX 5200
SERIAL NO :
microSD
ETHERNET MUSIC SERVER
RIGHT
100mA
Connection to WIFI router for wireless transmission
DUAL CHANNEL DIGITAL MEDIA PLAYER
Connectivity
- LAN interface
- Common protocols
- Priority Protocols
Audio
- Analogue input (peak-to-peak)
- Input load capacitance
- Digital format
CH 2
FM
a m pe re s
OFF/ON
Power requirement :
Voltage
Current
CH 1
FM
MP 1020
/ V-
/ V+
MODE
MIN
MAX
MIN
MAX
OFF/ON
/ V-
/ V+
MODE
MP1020
Analogue
Inputs
<100 mA
STREMING
UP
NEXT
DOWN
PRE
SOURCE
IPX 5200
1
2
3
4
5
6
7
CD1001
8
amperes
POW
START / STOP
RJ-45, 100Mb/s
UDMP, ADP
1.25Vrms
30 Ohm
100 pF
0.1%
83 dB
IMA ADPCM / MP3 (CBR / 320 kbps max) /
WAV
microSD
(SD Card Input)
amp
eres
iPX5200
iPX
ETHE
RNET
MUSIC CLIENT GROUP
ETHERNET MUSIC SERVER
ADD
53
ETHE 00
RNET
MU
RESS
SIC
LAN
LINE
NCEDUT
BALA
OUTP
CLIEN
T
LOCATION N
RESET
ETHE
RNET
iPX5300
Music Client
LOCATION 1
amp
eres
iPX
ETHE
RNET
ADD
53
ETHE 00
RNET
MU
RESS
SIC
LINE
NCEDUT
BALA
OUTP
CLIEN
T
RESET
Firmware upgrade
255 Max
Crome V25+, RS485
Via Web Browser
Temperature
Humidity
-20°C ~ 80°C
0 - 70%
Case :
Dimension
Weight
482 x 44 x 180 mm
1.9 kg
Client connection
User interface
Local
PA System
RNET
ETHE
iPX5300
Music Client
LOCATION 2
Local
PA System
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.9 kg
7
iPX5000 Series
IP Based System
amperes
iPX5300
iPX5151
Ethernet Music Client
Ethernet Paging Client
Introduction
Introduction
iPX5151 is the Ethernet Paging Client which receives and transmits paging audio and
RS486 data from digital paging microphone, which is then fed to PA mixer for
amplification.
iPX5300, Ethernet Music Client is used to receive audio streaming from central rack
either from iPX5200 Ethernet Music Server or via PMX II LAN. Quality sound can be
expected as it plays MP3 audio at up to 320 kbps.
iPX5151 replaces iPX5150 with a totally improvised architectures, notably on the
operational protocol and size reduction. Multicast transmission is now employed,
enabling it to send audio or data at faster rate and the quantity of clients in a network
can be up to 255 units.
The application of iPX5300 is rather simple, as depicted in the diagram in page 7
(iPX5200). It shall be installed at remote buildings and its balanced audio output shall be
fed to mixer and thereafter amplifiers. Settings of each module is through http for bass
and treble, volume, ID, etc.
Parameter settings is done using http, connected directly to the unit for channel
setup, bass and treble controls, volume, etc.
iPX5151
<100 mA
Connectivity
- LAN Interface
- Common Protocols
- Priority Protocols
RJ-45, 100Mb/s
UDMP, ADP
Audio
- Analogue in/out (peak-to-peak)
- Input load Capacitance
- Digital format
User interface
Firmware upgrade
Packing information
Qty per carton
: 1 unit
WxHxD
: iPX5151 / iPX5300
: 168 x 102 x 190 mm
Weight
8
: iPX5151 / iPX5300
: 1 kg
iPX5300
Power Requirement :
Voltage
Current
Temperature
Humidity
Case :
Dimension (WxHxD)
Weight
1.25Vrms
30 Ohm
100 pF
0.1%
83 dB
IMA ADPCM / MP3 (CBR / 320 kbps max) / WAV
(Web Browser) IE V8+, Firefox V22+, Google Crome V25+, RS485
Via Web Browser
-20°C ~ 80°C
0 - 70%
100 x 147 x 40 mm
300 g
iPX5500
IP Communication Box
amperes
IP Based System
Introduction
iPX5500 is the communication interface for equipment with RS485 outputs and remote
PC, enabling remote monitoring and controls via Amperes PMX II LAN software. It
converts RS485 data received from equipment into IP and shall be received by remote
PC in the LAN environment. Likewise for remote controlling, user would be able to
perform setting or changing parameters via the software modules available in PMX II
LAN.
Among devices available are QP Series of amplifiers, LS4600 line surveillance unit,
AX3800 auto amplifier changeover panel and PS9400 battery charger. The list shall be
expanded further in due time. With combination of iPX devices available, user shall have
better controls and monitoring of PA equipment to ensure smooth running with minimal
downtime, especially during emergency.
Features
Converts UART interface to IP for monitoring and controls via LAN
Birectional RS485 data communication
Up to 16 devices per comm box
PC WITH PMX II LAN
SOFTWARE
Compatible with other UART devices
Simple setup via http
Management Room
NETWORK SWITCH
CONNECTION VIA
LAN OR FIBER
Control Room Rack
NETWORK SWITCH
TO OTHER iPX DEVICES
QP POWER AMPLIFIERS
iPX5500 COMM
INTERFACE
RS485 / UART
CONNECTIONS
Power requirement :
Voltage
Current
12~ 24V DC (Normal DC 24V)
<100 mA
Connectivity
- LAN interface
- Common protocols
RJ-45, 100Mb/s
Firmware upgrade
Crome V25+, RS485
Via Web Browser
Temperature
Humidity
-20°C ~ 80°C
0 - 70%
Case :
Dimension (WxHxD)
Weight
200 x 120 x 30 mm
600 g
User interface
QP POWER AMPLIFIERS
LS4600 LINE SURVEILLANCE
PS9400 BATTERY CHARGER
FI6000 PHASE CONTROLLER
Packing information
WxHxD
: 512 x 83 x 288 mm
Weight
: 1.55 kg
PT1801 TIMER
9
PMX II V2
Software
Media Playback
Music Server Software
Media Library
amperes
Calendar Scheduling Emergency Call
PMX II is software that consists of virtual hardware components such as Music
Player, Music Storage, Programmable Timer, Message Player and Paging Station. It
is a standalone version and runs on PC with operating system of Windows 7 and
above. With a converter as dongle, the audio and control outputs from PC shall be
fed to conventional PA rack, enriching the entire installation to a more sophisticated
setup.
Main Page
The user interface had been made to be user friendly, enabling smoother setup and
viewing. The system shall be able to integrate freely with existing equipment such as
zone decoders, paging microphones with different priority level and emergency
paging panel which the activities would be monitored in the screen.
Among suitable installations includes offices, transportation stations, malls, hotels,
schools, etc.
Media Library
Features
Media playback module to feed BGM audio to PA system for MP3, WAV or other
supported audio files by Windows Media Player.
Media Library to store unlimited songs, messages, tones or chimes in HDD for
playback
Weekly programmable timer allows repetitive playback of tones or chimes
Calendar scheduling to playback songs such as birthday songs
Controls up to 256 zones which is linked to external zone selector such as
ZS5121 via TD6240
Zone configuration allows naming each zone to specific name and assignable
as Normal or Emergency zone.
Paging or messaging to zone or groups of zones, with priority overriding for
Emergency Call
PC Paging Interface
PC MIC
PM1000
PAGING MIC
PC
PC audio
output
PMX6500
External Device Status
Audio + Data
(2 pair screen)
USB output
Other audio
inputs
Lower priority
setting
Audio
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
E X T IN P U T
OFF
M A S TE R
TON E CTRL
MX 2122
S E LE C T
TUNER
OFF
M IN
M IN
MAX
M IN
S IG IN
MAX
S IG IN
M IN
MAX
M IN
S IG IN
MAX
S IG IN
M IN
MAX
S IG IN
M IN
S IG IN
MAX
M IN
MAX
M AX
C H IM E
M IN
POW ER
I
CASS
CD
AUX
M AX
M IX E R
T R E B LE
BASS
M IN
S IG IN
a m pe r e s
O
MAX
M U S IC S O U R C E
S IG IN
MX2222 MIXER
TD6240 DECODER
a m pe r e s
AMPLIFIER
PD2400 /
PD2800
POW ER
M ENU
Q P 2 5 00
Higher
priority
Audio + Data
(2 pair screen)
I
a m pe r e s
O
UP
DOWN
5 0 0 W 1 0 0 V L IN E P O W E R A M P LIFIE R
Switching signal
ZONE SELECTOR
ZS 5121
a m pe r e s
O V E R R ID E
10
1
2
3
4
5
6
7
SPEAKER ZONE SELECT
8
9
10
11
12
ALL
CALL
SPEAKERS
Stand alone setup of PMX II
PMX II Xtended
LAN Based PMX System
amperes
Software
PMX II LAN version has all the features of PMX II standalone but it runs
on LAN environment and would be able to work with other Amperes IP
products such as Music Client, Communication Box and soon the IP
MatriMix. In addition, it contains the extension modules of equipment
User Interface, such as QP2000, FI6000, AX3800 and other upcoming
models which would be available for free updates.
With the extension modules, user shall be able to control and monitor
status of equipment from multiple locations within the local area network.
Among them, controlling the volume control of power amplifiers, fault
changeover notifications, emergency paging activation alert and so forth.
Application of these extensions would require the usage of iPX5500
communication box, which receives RS485 data from equipment and
send to the PMX software and vice versa.
With the advent of IP technology in PA systems, PMX II LAN would be the
essential component sought after and it is a cost efficient way to an
advanced paging system.
Paging Mic
PC with PMX II (1)
Paging Mic
PC with PMX II (2)
LAN
System (1)
System (2)
iP Client
Music Client
iP Client
iP - UART
Communication interface
iPX5500
Components in PMX II LAN
Paging and message
Click to access paging control panel
Combox Manager:
Interfacing to external equipment for monitoring and control
Client Info :
Showing music clients connected to system
Scheduling
Events / messages scheduled for playback
Playback Controls :
Control buttons for music playback
System message:
Status of PMX communication
Emergency Paging Status :
Indications for emergency paging in progress
Playlist :
List of messages or songs for playback
PACKING INFO:
- Software CD
- PMX II stand alone only:- PMX6500 USB to RS485 converter
WxHxD
: 190 x 168 x 102 mm
Weight
: 1.05 kg
PMX IP Info :
Information of PMX IP address
HARDWARE REQUIREMENT :
PC with 4GB RAM ( higher RAM required for simultaneous multichannel music playback )
with Windows 7 / 8 operating system. Intel i3 and above processor or equivalent
recommended.
11
PRODUCT SELECTION GUIDE
Amperes has variance of products to choose from for practically almost applications, be it a simple mixer
amp or more complex audio distributions with multiple building blocks.
SQ 9715
The table below provides a quick equipment selection guide. As quantity or product type may vary for
different applications, such as size, budget or customer’s requirement, you are welcomed to contact us for
free consultation.
AM 4120
CD 1001
a
An
l
g
lo
ic
s
Ba
ue
at
IP
M
No
MODEL
1
iPX5101
√
√
√
√
2
iPX5151
√
√
√
√
3
iPX5200
√
√
√
√
4
5
iPX5300
√
√
√
√
√
6
PD2000 Series / PD1160
√
√
√
7
PD1240 / PD1280
√
√
√
8
EP1200A
√
√
√
√
9
CM1400
√
√
√
√
√
√
√
√
√
√
√
√
√
√
PM1000 Series
√
d
se
rix
ita
g
Di
I
O
Ba
√
CM 1400
FIRE
BP 2000
10
CD1001 / MP1020
11
MR1300 / MR1301
12
TD6240 / TD6080
√
√
√
13
PT1800 / PT1801
√
√
√
√
14
FI6000
√
√
PMX Systems
√
√
√
√
√
15
16
MxP2188 / MxP2288
√
√
17
ER1108
√
√
18
RP1104 / 1105
√
19
MX2222
√
√
√
√
√
20
DA2208
√
√
√
√
21
QP2000 Series
√
√
√
√
22
PA2000 Series
MA / MC2000
√
√
√
23
√
24
PA310 / 320 / 330
√
√
√
√
√
√
25
AX3800
√
√
√
√
26
AX700
√
√
√
√
27
AS4000
√
√
√
28
AC3601
√
√
√
29
AM4120
√
√
30
31
LS4600
ZS5601 / 5121 / 5602
√
√
√
√
√
√
√
32
SS6401
√
√
√
√
33
SQ9715
√
√
√
34
35
BC9730 / BC9740
√
√
√
√
√
√
√
√
√
√
√
√
PS9400
√
√
√
√
√
36
VR7600
√
√
√
37
AV7200
√
√
√
√
√
38
VC7000 / 8000
√
√
√
√
√
39
VP7501 / 7810
√
√
√
√
√
√
BP 1000
IPx 5100
TD 6240
TD 6080
MxP 2188
ER 1108
MX 2222
DA 2208
√
√
SS 6401
ZS 5601
ZS 5121
ZS 5602
PT 1800
MSG 2
MR 1300
a m pe re s
LS 4600
VR 7600
AC 3601
AX 700
Basic setup : restaurants, meeting rooms, lecture halls, mobile PA
Analogue : small buildings, offices, entertainment outlets, schools
Digital
: medium size or high rise buildings exceeding 12 zones, hypermarkets,
university / college campus
Matrix
: Bungalows, club houses, entertainment centre, offices which require flexible music selection
IP System : Large scale installations with multiple blocks, remote installations, transportation hub or
stations, universities, etc
AMP. NORMAL
AX 3800
AMP. FAULT
PILOT TONE
AMP. CHANGEOVER
AMP. NUMBER
amperes
STANDBY AMP. FAULT
1
2
3
4
5
6
7
8
PS 9400
PREV
ENTER
MENU
NEXT
POWER
BC 9740
CHARGING
amperes
FAULT
PA 2480
AUTOMATIC BATTERY CHARGER
PA 2480
BC 9730
MA 2024
VP 1000
MA 2012
VP 3000
MC 2112
Product outline drawings can be downloaded from our
website
QP 2000
PD1000 Series
amperes
Digital Paging Mic
PD1240 | 24 Zone Digital Paging Microphone
PD1280 | Digital Paging Microphone
Sensor Touch
Multipoint Paging
Priority
Introduction
Features
Sensor touch keypad with impressive outlooks
PD1240 and 1280 are enhanced versions of the popular PD2000 series incorporating
soft touch buttons and improved sound quality. All essential features such as Priority
level assignment, multipoint paging, illuminated gooseneck microphone and volume
controls are included.
LED indicators for PD1240 and large LCD display for PD1280
Suitable for multipoint paging with priority level setup
Improved sound output
PD1240 is a 24 buttons zone control with 4 fixed groups with ALL CALL, suitable for
small setup. For larger installations of up to 254 zones, PD1280 shall fit into the requirement which comes with large LCD panel and programmable 9 priority levels.
Built in chime
Adjustable volume controls for chime and microphone
Name setting at PD1280
Compatible with Matrix Controller and TD Series of Zone Decoders, IP Client
iPX5151
PD1280
PD1240
PD1240
Operating voltage
Power consumption
Zone selection
Switching selection
Microphone
Output impedance
Output level
Output controls
Data connections
Cabling to decoder
Recommended operating distance
Compatible interfacing device
Chime
Indicators
Displays
Frequency response
S / N ratio
Gooseneck mic length
Dimension (W x H x D)
Weight
PD1280
24V DC via EX2800 with local power adaptor
1.2 W
1.3 W
24 zone keys,
Numerical keypad with
Group, All Call
Group, All Call
Sensor touch keypad
Gooseneck condenser capsule ; unidirectional
600 Ohm
1.2V balanced line output
Chime, mic volume
RS485; 19.2 kbps
2 pair screen; 22 AWG / Cat 5e decoder
500m subjected to cable size
MxP2188, TD6240, TD6080
4 tone up and 4 tone down
Zone, power, audio, data, gooseneck ring LED
NIL
LCD display; white back
illumination
100 - 12 kHz
>65 dB @ 1 KHz
400 mm
230 x 192 x 65 mm ( Excluding Mic)
1.6 kg
At remote location
PD1240
Mic Nbr 2
12V DC
via adaptor
Cat 5e
EX2800
PD1240
Mic Nbr 1
12V DC
via adaptor
EX2800
Cat 5e
PD1240
Mic Nbr 3
EX2800
2 pair screen cable
Cat 5e
TD6240 Zone Decoder
(24 channel)
MX2222 Pre-amplifier
Mixer
8 core cable ( Cat 5 )
connection via RJ45 Jack
Power Amplifier
Each cable to cater for 6
zones
ZS5121 Spk Zone Selector
(Zone 1 to 12)
ZS5121 Spk Zone Selector
(Zone 13 to 24)
Speakers
13
PD Series
amperes
Digital Paging Mic
24 Zone Digital Paging Microphone | PD2400
Digital Paging Microphone | PD2800
8/16 Zone Remote Paging Microphone | PD1160
Grouping
PD2800
Priority
These classic digital paging microphones are suitable for remote paging setup over long
distance, typically within 500m. With their harmonised protocols, they are compatible with
all TD decoders and Matrix controller via RS485 data.
With multipoint paging of several PD mic, user shall be able to set priority level of each
mic according to the priority needs, allowing unit with higher priority to override lesser one.
It is suitable for large scale installations of up to 256 zones, enabling 9 groupings of 12
zones each. Features including :
Programmable zone grouping ie. Storing selected zones in groups to enable faster
access to paging.
9 priority level settings ie. Enables 9 multipoint paging station with 9 levels of priority
LCD display for easy monitoring
PD2400
PD1160
It is suitable for mid-size installations of up to 24 zones. Among its distinctive features
include :
24 direct zone key with 4 groups with ALL CALL.
Built in 4 tone chime with Chime and Mic volume controls
Up to 3 priority level setting
It is a simple and dedicated paging microphone for connection to MxP2188 MatriMix
system with 8 / 16 zones call station.
Multipoint paging with EX1102 mic extender
Power requirement
Power consumption
Zone selection
Microphone
Output impedance
Output level
Output controls
Data output
Data connection
Operating distance (data)
Audio distance
Chime
Indicators
Frequency response
S/N ratio
Dimensions (WxHxD)
Weight
14
Direct connection to MxP2188 controller.
PD2400
PD2800
24V DC via RJ45 connected to EX2800
170 mA
420 mA
24 individual zone key
Numerical keypad
4 groups (preset of 6 zones)
ALL CALL
Condenser microphone cardioid
600 Ohm balanced
1.2 V (line output)
Chime and mic level
RS485; 19.2 KBs
RJ45 to EX2800 via Cat 5E / 6 cable ; 2P screen to decoder
Up to 1000 m (sub. to cable size)
Typ 500 m (sub to cable size)
2 or 4 tones; assignable
LCD Display
Mic ring, zone switch
100 ~ 12 KHz
> 60 dB at 1 KHz
400 mm
292 x 62 x 186 mm (body only)
1.3 kg (excl. adaptor)
PD1160
24V DC via MxP2188
800 mA
8 / 16 zone keys with ALL CALL
Mic level
RJ45 to MxP2188
300 m
300 m
-
Power, source, volume, busy
1.0 kg
PM1000 Series
amperes
Analogue Paging Mic
PM1000 | Dekstop Paging Microphone
PM1060 | 6 Ch Dekstop Paging Microphone
PM1120 | 12 Ch Dekstop Paging Microphone
Introduction
Features
PM1000 analogue series are available in three variants and had been serving many installations faithfully since its creation. They are available as simple paging mic with chime to those
with 6 or 12 zone selections. They are most suitable for simple and small size installations of
less than 12 zones in total.
Condenser gooseneck microphone with illuminated ring
Pre and post announcement 4 tone chime
Adjustable chime and mic volume with balance mic / line output level
Output level selection to mic or line signal to suit the input type of the
pre-amplifier mixer
Dry contact available when mic is active (PM1000 only)
6 or 12 zone selection for PM1060 and PM1120
PM1000
PM1060
PM1120
24V DC via D9 conn.
24V DC adaptor
150 mA
150 mA
50 mA
ALL CALL
6 and 12 zones w ALL CALL
Condenser microphone cardioid
600 Ohm
1.2 V (line output) / balanced mic (775 mV )
Power requirement
Power consumption
Zone selection
Microphone
Output impedance
Output level
Output dry contact
Output controls
Audio connection
Switching connection
Operating distance
Chime
Indicators
Frequency response
S/N ratio
Dimensions (WxHxD)
Weight
3 A normally open
Chime and mic level
1/4 " stereo phone jack
D15 connector
2W connector
300 m (recommended)
Mic ring, zone switch, ALL CALL
PM1000
100 ~ 12 KHz (+/- 3dB ; 0 dB out)
> 60 dB
400 mm
150 x 62 x 186 mm (excluding mic)
800 gms
800 gms
850 gms
PM1060
PAGING MIC
Audio : 2C screen
MIXER
OFF
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
TUNER
MIN
MAX
SIG IN
MIN
MAX
SIG IN
MIN
MAX
MIN
SIG IN
MAX
SIG IN
MIN
MAX
SIG IN
MIN
SIG IN
MAX
MIN
MAX
MAX
CHIME
MIN
PM1120
POWER
TONE CTRL
OFF
MIN
POWER
PM1000 Via
adaptor,
PM1060 / 1120 via
D conn
SELECT
MASTER
EXT INPUT
MX 2222
I
CASS
CD
amperes
O
AUX
MAX
MIXER
TREBLE
BASS
SIG IN
MIN
MAX
SIG IN
MUSIC SOURCE
E/M PAGING
MIC
TEST
FIRE
SIREN ACTIVATE
AM 6000
POWER
amperes
POWER AMP
PA 2060
60 Watts
POWER
POWER
AM 6000
I
PROTECT
O
SIGNAL -10 dB
amperes
CLIP
SIGNAL -40 dB
Zone Control :
PM1000 - 2C
for all call,
PM1060 / 1120
8 / 16 core
ZONE SELECTOR
ZS 5121
amperes
OVERRIDE
1
2
3
4
5
6
7
SPEAKER ZONE SELECT
8
9
10
11
12
ALL
CALL
TO LINE SURVEILLANCE /
VOLUME CONTROLLER /
SPEAKERS
Packing information
WxHxD
: 512 x 83 x 288 mm
Weight
: PM 1000 - 1.5 kg ( incl adaptor )
: PM 1060 - 1.15 kg
: PM 1120 - 1.2 kg
Rear View Of PM1000
Rear View Of PM1060 / PM1120
15
EP1200A
Paging Microphones
Siren Tone
Activation
Emergency Paging Panel
amperes
RS485 Interface
Introduction
Emergency Paging Panel is an essential tool for firemen during emergency, allowing
direct paging to all zones and bypassing any active BGM or paging in progress.
EP1200A is enhanced with communication port, enabling the unit to be used with
iPX5151 IP Client for a LAN based setup. This shall allow simultaneous emergency
paging or siren activation for entire multiple sub racks available in the system.
Features
Built in siren tone generator (constant signal)
Visual FIRE indicator
External voice message activation
Dual mode siren tone activation
Dry contact when paging mic is activated
Priority paging via front panel microphone, bypassing all other audio sources
Output level controls for siren and message / paging microphone
Application in conventional system
MX2222
OFF
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
TUNER
MIN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
SIG IN
MIN
MAX
SIG IN
MIN
SIG IN
MAX
MIN
MAX
MAX
CHIME
MIN
TREBLE
BASS
MIN
O
MUSIC SOURCE
line out
line
EP1200A
amperes
AUX
MAX
SIG IN
a m pe re s
MESSAGE RECORDER
I
CASS
CD
MAX
MIXER
SIG IN
contact
MSG 2
MR 1300
MAX
POWER
TONE CTRL
OFF
MIN
MIN
SIG IN
TRIGGER SWITCH
SELECT
MASTER
EXT INPUT
MX 2222
FIRE
all call
activation
POWER AMP
POWER
PA 2480
amperes
PROTECT
CLIP
SIGNAL -10 dB
SIGNAL -40 dB
PUBLIC ADDRESS POWER AMPLIFIER
100V
SPEAKER
ZONE
SELECTORS
ZS 5121
1
2
3
4
5
6
7
SPEAKER ZONE SELECT
8
9
10
11
12
16
24V DC
3.5W
MICROPHONE
Mic sensitivity
Impedance
Frequency response
-72 dB Omni directional
600 Ohm
300 ~ 8 KHz
SIREN
Siren frequency
Siren duration
Siren activation
Continuous at 8 KHz
Continuous when activated
Front test switch / remote contact
Input channel
Output level
Priority sequence
Indicators
Dimension (WxHxD)
Weight
Pre-amplifier output, message recorder
Balanced line out (1.2V)
Paging mic - siren - message - pre amp in
Front FIRE with backlight illumination
482 x 88 x 180 mm
3.0 kg
ALL
CALL
Rear View:
24V
O/R
Power requirement
Power consumption
amperes
OVERRIDE
VOLUME
CONTROLS
SPEAKERS
Packing information
Qty per carton
: 1 unit
WxHxD
: 560 x 165 x 295 mm
Weight
: 3.6 kg
CM1400
Input Sources
Chime and Siren Tone Generator
amperes
Features
Introduction
Selectable output as balanced or unbalanced line
CM1400 offers 5 chimes and 2 siren tones with selectable balanced and unbalanced line
output. Activation of chime shall be from front switches or via remote triggering terminal,
enabling the unit to be linked to external sensors or triggering system such as alarm panel,
remote mic or emergency switch. Siren has priority over chimes.
Front panel switch activation or via remote trigger port
It is suitable for installation in schools, factories, hazardous areas etc.
5 types of chimes and 2 siren
Adjustable output volume
* Customised tones available upon request.
Rear View:
RELAY OUTPUT CONTACT
MELODY
a m pe r e s
E/M SWITCH
contact
NO
contact
SIREN
CM 1400
PT1800
WAVY
4T UP
4T DWN
2T UP
WEST'R
BELL
amperes
POWER
CHIME / SIREN TONE GENERATOR
chime input
OFF
SELECT
POWER
MASTER
EXT INPUT
CH1
MX 2122
CH2
CH3
CH4
CH5
CH6
TONE CTRL
TUNER
OFF
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
I
SOURCE
MIN
MIN
SIG IN
MIN
MAX
MAX
CHIME
SIG IN
MIN
CASS
CD
MAX
MIXER
TREBLE
BASS
MIN
SIG IN
Other Inputs
AUX
O
MAX
MUSIC SOURCE
CM1400
Operating voltage
Power consumption
Chime type
MX2222
line out
Siren type
E/M PANEL
FIRE
External activation
Output
Output impedance
Gain
Dimensions (WxHxD)
Weight
To power amplifier and speakers
Packing information
Qty per carton
: 1 unit
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.15 kg
24V DC ; 0.5 A
0.3 A
4 tone up, 4 tone down, 2 tone
Ringing bell, Westminster
Constant siren 8 KHz
Wavy siren
Dry contact
Line 1V
10 K Ohm
+4 dB max
482 x 44 x 180 mm
1.55 kg
MICROPHONES
Condenser Gooseneck Mic | GM 8 / GM 9
Handheld Compact Mic | GM338
Condenser Tie Clip Mic | TC122
GM8
GM9
Condenser Gooseneck Mic
Condenser Gooseneck Mic
GM338
Handheld Compact Mic
TC122
Condenser Tie Clip Mic
GM8
Capsule
Polar pattern
Frequency response
Sensitivity
Output impedance
Power supply
Dimension
Weight
GM9
GM338
Back electret condenser
Uni directional
20Hz ~ 1.6kHz & 200Hz ~ 20kHz
50 ~ 16 KHz
82 ± 3 dB
-45 dB ± dB
1 K Ohm
50 Ohm
9 ~ 12V DC Phantom power supply
400 mm
495 mm
120 x 63 mm
60 gm
90 gm
190 gm
TC122
50 ~ 16 KHz
-45 dB ± dB
600 Ohm
7.8 dia x 25 mm
40 gm
17
Media Players
amperes
Input Sources
CD1001 is a rack mounted integrated CD / MP3 / AM FM tuner media player built
specifically to serve BGM requirement in your PA installation. Local listening is
available with headphone jack or via the built in speaker.
Features
USB
Plays various format of CD audio, AM / FM tuner and MP3 via USB
CD
AM / FM
Headphone
Headphone jack and monitor output for pre-broadcast listening
CD1001
CD / MP3 / AM-FM Tuner
MP1020
2 CH Media Player
MP1020 is a two channel digital media player in a single rack unit. Both the modules
operate independently and shall be able to play files from SD Card, USB as well as
receiving FM audio.
Features
Dual channel BGM source in a box
Plays files from SD card, USB drive and FM radio reception
Rear View CD1001:
Headphone monitoring
Packing information
WxHxD
: 560 x 165 x 295 mm
Weight
: 5.35 kg
MP1020
2 CH DIGITAL MEDIA PLAYER
Rear View MP1020:
CH. 2
CH. 1
CH. 2
CH. 1
LEFT
OFF/ON
RIGHT
ANTENNA
AUX OUTPUT
LINE INPUT
MP1020
18
Operating voltage
Power consumption
Playback media
Supported files
Aux audio input
Audio output
Output voltage
Weight
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.2 kg
CD1001
24V DC 1A
180mA
USB, mini SD Card, FM radio
MP3, WAV
RCA Stereo Line In
RCA Stereo
LINE Out 1.2V unbalanced
482 x 44 x 180 mm
1.8 kg
Playback system
CD / CD-R / CD-RW / MP3 / Tuner
CD / USB
Frequency response
S/N ratio
Channel separation
Noise
Distortion
20 - 20 KHz
70 dB
> 45 dB
4 mV
< 0.5%
TUNER
Tuner frequency
S/N ratio
AM : 522 - 1620 KHz
FM : 87.5 - 108 MHz
55 dB
Audio output
Output jack
Headphone output
Headphone volume
Working temperature
Power supply
Power consumption
Dimensions (WxHxD)
Weight
500 mV
Stereo, RCA jack
1/4” phone jack
Via front VC, +4 dB gain
45˚C
230 - 240V ac
1.8W at 240V ac
482 x 88 x 180 mm
4.4 kg
MR1301
Input Sources
Message Recorder / Player
amperes
Introduction
ARM 32 bit
Processor
MP3 Quality
16GB Memory
PC Interface
The all new MR1301 has loads of features for flexibility in operation and performance for
any demanding applications which runs on 32 bit ARM processor. It supports larger SD
Card memory size of up to 16GB, offering flexible file / message arrangement or
naming.
32 bit ARM chip for faster and multitasking processing of data
User shall be able to group different messages with delays in between for every single
message bank with high quality MP3 format of 320 kbps. All settings can be done easily,
offline through the SD Card and the configurator software provided. Another key feature
is the auto firmware updates, making MR1301 a tool that would work to contemporary
needs.
Up to 16GB of memory space using Micro SD card
Rear View:
Features
Message playback via front direct access button and rear remote triggering
DC 24V
+
High quality MP3 playback of up to 320 kbps
64 kbps IMA ADPCM voice recording for better clarity
Flexible message configuration in every memory bank eg. Multiple files in a single
button
Priority message playback with dry contact activation
Playback controls ie. Volume, Repeat, Bass and Treble
RS485 output with PC link for remote monitoring or using iPX5400 UART-IP
converter for monitoring and control via LAN ( Application software : PMX II LAN )
Auto firmware update / detection upon power up
Alternative setup at PC via “MR1301 configuration” software
External Contacts for Message
Triggering ( Up to 16 contacts )
NOTE:
Only Voltage free contacts
allowed for remote triggering
Alternative Bypass :
Audio and Trigger
direct to EP1200A
Balanced Audio
( line in )
CH1
Operating voltage
Power comsumption
Data communication
Inputs
Processor
Message trigger
File format
MP3 quality
Voice recording
Files in single bank
Delay set up in playback
Priority message cut
Software interface
Remote view / control
Indicators
Memory
Weight
24V DC
1W
RS485 at 19.2 kbps
Line inputs; unbalanced via RCA jack
Microphone input; via front phone jack
32 bit ARM
16 front and rear message
MP3, WMA, WAV
320 kbps
IMA ADPCM 16 KHz Sampling Rate
Bit Rate : 64 kbps
Up to 20 per message / button
Yes
Yes
Yes
Yes
LED at switches, LCD display
MicroSD up to 16 GB
482 x 44 x 180 mm
2 kg
Note :
With direct
connection to
EP1200A, message
shall bypass
audio signal from
MX2222 with
higher priority
MR1301 MESSAGE
RECORDER / PLAYER
CH2
CH3
CH4
CH5
MX2222
CH6
SO URCE
E X T IN P U T
TON E CTRL
OFF
M ASTER
MX 2222
SELECT
TUNER
OFF
M IN
M IN
MAX
M IN
S IG IN
MAX
S IG IN
M IN
MAX
S IG IN
M IN
MAX
S IG IN
M IN
S IG IN
MAX
M IN
MAX
S IG IN
M IN
MAX
M AX
C H IM E
M IN
PO W ER
CASS
CD
amperes
AUX
M AX
M IX E R
T R E B LE
S IG IN
Bal. Audio
to Pre-Amp input
BASS
M IN
S IG IN
M AX
EP1200A
FIRE
Amp input
AMPLIFIERS
PA 2120
120 Watts
PO W ER
POW ER
PA 2120
PROTECT
I
C L IP
O
a m pe re s
S IG N A L -10 dB
S IG N A L -40 dB
100V Output
24V Override Trigger
to ALL CALL Conn.
O V E R R ID E
ZS5121
a m pe re s
O V E R R ID E
2 x 100V Audio
2 x 24V Override
VC VOLUME
CONTROLLERS
SPEAKERS
The above diagram shows typical schematic using MR1301 as message player, either for
general repetitive message playback or for emergency voice evacuation purpose.
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.6 kg
19
PT1801
Multichannel Programmable Timer
Inputs Sources
Weekly & Event
Date
PC Interface
Clock Backup
amperes
Built In Chime
Introduction
Features
The all new PT1801 now packed with better features, notably with its setup or
programming process. The user friendly “PT1801 Configurator” software is available
for download from website and programming of schedules, upload or recall programs
can be done at breeze.
8 output triggering ports with user selectable contact options
PT1801 is useful for schools, factories, malls, etc. which shall work to provide reliable
time reminders for various events of the day. Its 250 programmable steps with 8
output contacts shall cater for needs of various industries.
RS485 data for remote monitoring
COM
COM
UNBALANCE
LINE OUT
OUTPUT
LEVEL
RELAY DRY CONTACT
Optional PC Interface
PAGING MICROPHONE
( Normal / Zone Selection )
Audio Output
(Balanced / Unbalanced )
OFF
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
SELECT
TUNER
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
MAX
MAX
CHIME
MIN
Audio output ( unbalanced )
TONE CTRL
OFF
MIN
MIN
SIG IN
POWER
MASTER
EXT INPUT
MX 2222
Zone
Triggering
Westminster chime output with adjustable volume
CH8
NO
COM
CH7
NO
COM
CH6
NO
COM
CH5
NO
COM
COM
CH4
NO
COM
CH3
NO
CH2
NO
CH1
NO
+
User interface software for ease of programming
Rear View:
DC 24V
250 preset triggering times with free assignment to any of the output ports
PRE-AMPLIFIER MIXER
TREBLE
BASS
MIN
SIG IN
I
CASS
CD
MAX
MIXER
SIG IN
MAX
MUSIC SOURCE
amperes
AUX
O
Only when
Ch.8 is used
Mini USB
Cable
RELAY OUTPUT CONTACT
MELODY
a m pe r e s
PT1801
POWER AMPLIFIER
Input voltage
Power consumption
24V DC ; 0.5A
4.8W
Output channels
8
Triggering mode
ON, OFF, pulse (3 seconds)
Memory
250 preset time
Contact rating
3A
Indicators
LED for triggered channel, Melody,
Standby
Output chime
Westminster (Ch. 8 only)
Chime output level
Line level ; 1.2Vrms
Volume attenuation
Output connection
off to 0 dB
1/4” phone jack ; unbalanced
Impedance
1K Ohm
Clock backup
CR1220 button battery
RTC accuracy
Data link
± 2ppm
RS485
Baud rate
Dimensions (WxHxD)
19.2 kbps
482 x 44 x 180 mm
Weight
2 kg
Zone Triggering ( optional )
or connect to Message Playback equipment
SPEAKER
ZONE SELECTOR
Speakers
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.5 kg
20
FI6000
Input Sources
Fire Alarm Interface
amperes
Scalable
Integration
Phased Evacuation
Programmable
PC Interface
Introduction
Features
FI6000 is a phase evacuation controller which can be integrated with various Amperes
equipment such as zone decoder and voice message player for interfacing with Fire
Alarm System.
Integration with Amperes products via RS485 interface and Fire Alarm System
via dry contacts
As part of requirement of EN54, it is necessary that voice alarm to be broadcasted
according to zone(s) for orderly evacuation or warning purposes. FI6000 performs the
task required by triggering appropriate announcement and intended broadcast zones.
Easily programmable for phased evacuation announcement
Available in 24 zone per panel and scalable to cater for larger number of zones
Provided with FI6000 Configurator software for easier setup
Bicolour LED for easier status indication for each incoming sensors
FI6000 can be configured via configurator software and is flexible in its setup.
Rear View:
PD SERIES
PAGING MIC
INPUT SOURCES
FROM FIRE ALARM INTERFACE / BAS
SENSORS ( VOLTAGE FREE )
amperes
MX2222
PRE AMPLIFIER MIXER
CH1
CH2
OFF
CH3
CH4
CH5
CH6
SOURCE
SELECT
TONE CTRL
TUNER
OFF
MIN
MIN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
SIG IN
EP1200A
MIN
MAX
SIG IN
MIN
MAX
SIG IN
MIN
POWER
MASTER
EXT INPUT
MX 2222
MAX
MAX
CHIME
MIN
I
CASS
O
AUX
CD
MAX
MIXER
TREBLE
BASS
SIG IN
MIN
audio
amperes
MAX
SIG IN
MUSIC SOURCE
VC 24V trigger
USB
RESET
SNOOZE
STOP
INPUT & OUTPUT
CH1
CH2
FI 6000
amperes
CH3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
CH4
RELAY OUTPUT
FIRE ALARM INTERFACE
Input :
Operating voltage
Current source idle
Current source channel and relay trigger
Power consumption idle
USB input
Communication control
Baud rate
Unit cascade control
Channel input
Software configuration
24V DC
20mA
0.10A
0.48W
USB to RS485 Driver
RS485
19200 bps
Software Control
24 Channel
FI6000 Configurator
Output :
Channel output
Contact rating
LED indicator
4 Channel
3A
28 LEDs
Case :
Dimension
Weight
482 x 44 x 180 mm
1.85 kg
EMERGENCY PAGING PANEL
EMERGENCY
PAGING
EMERGENCY / SIREN ACTIVE
EP 1200A
SIREN
MIC
amperes
FIRE
contact 2 to 4
(trigger EP 24V override)
audio
AMPLIFIER
POWER
MENU
QP2500
I
trigger contact ( s )
amperes
O
UP
Quantum
500W 100V LINE POWER AMPLIFIER
audio
RS485
data
DOWN
2000 SERIES
100V audio
TD6240
data & audio
PRIORITY 2
DATA
ACTIVE
PRIORITY 1
amperes
trigger switching
& 100V line audio
1
2
3
4
5
VC 24V trigger
6
7
8
9
10
11
OVERRIDE
12
ALL CALL
amperes
OVERRIDE
SPEAKER ZONE SELECTOR
MR 1301
PAGING ZONE SELECTION
ENTER
MENU
UP
NEXT
SHIFT
MSG 1
MSG 2
MSG 3
MSG 4
MSG 5
MSG 6
MSG 7
MSG 8
REC MIC
INPUT
amperes
REC
MESSAGE REC / PLAYER
24 CH DATA DECODER / RECEIVER
ZS 5121
MR1300 / 1
DOWN
PRE
POWER
TD 6240
DIRECT MESSAGE TRIGGER
audio out to MX2222
or EP1200A
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.5 kg
TO SPEAKERS
18
21
MxP2188
Mixer / Distribution
Matrimix Paging System
amperes
Introduction
Matrix Controller MxP2188 offers flexibility of routing input sources to the output
zones, as in many cases that different area of listening would have its own
preference to the type of music. It is a 8 x 8 controller but expandable to larger setup
of 128 zones.
Configuration
Power source
Inputs
Offices, club houses, shopping complexes, entertainment centers as well as high
end residential buildings are among places where it is suitable to apply MxP2188.
Essential functions such as emergency overriding, remote zone selection and audio
monitoring are integral features of the unit, thus making it a suitable equipment in the
PA setup.
Input connections
Input volume control
Bass and treble control
Phantom power
Priority input
Chime
Message recording
Output
Zone selection
Features
8 input and 8 output Matrix controller with inputs of either Mic or BGM or fed
from remote source panel.
Individual channel setup for bass, treble and volume.
Built in chime with selectable 2 or 4 tone output.
Built in voice recorder of up to 60 seconds.
E/M override contact
Audio monitor
via
Communication
Remote triggering
Audio output monitor for every zone.
Remote triggering port for message and siren.
Priority override dry contact port whenever ALL CALL is triggered.
Microphone input for paging at rack.
Remote paging desk connectivity to Amperes PD Series of paging microphones
Dimensions (WxHxD)
Weight
Link to Emergency Paging mic / EVAC voice message unit to comply with emergency
voice playing requirement.
Rear View:
8 x 8 ; Cascade to 8 x 128
24V DC ; 2A via adaptor
8 local BGM - unbal. line or
8 remote BGM via RP1105
1 remote paging mic PD1160
1 local mic input
RJ45 (remote) / RCA jack
XLR for local mic input
Manual adj. at each channel
+12 dB to -12 dB ; digital select
12V DC (local mic in only)
Local page, E/M message
2 or 4 tone built in
60 secs max in single bank
8 x balanced line output
Remote paging mic (PD1160) ;
Front panel with ALL CALL
3A dry contact
Source monitor with volume control
3W speaker
RS485 ; 19.2 Kbps
Siren (ALL CALL)
Message (ALL CALL / individual)
482 x 88 x 300 mm
6.0 kg
IP setup possible by using iPX5150 to enable longer or multi building communication.
BGM 2
PD1160 / PD2400 or PD2800
PAGING MIC
EP1200A
EMERGENCY PAGING PANEL
FIRE
EX1102 MIC EXTENDER
F RO
M
PD
IC
S PL
IT
M
A STER
MxP2188
TER
TO
SL
AMPLIFIER ZONE 1
1160
TO
M
AVE
AX3800
C/OVER
UP
MENU
amperes
L IN E
V O LU M E
DOWN
SPEAKERS
L IN E
8
M IC
PILOT TONE
RP1104
REM OTE CO NTRO L PANEL
R E M O TE S O U R C E P A N E L
STANDBY AMP. FAULT
M IC
Cat 5e/6
R E M O TE S O U R C E P A N E L
M O N ITO R S P E A K E R
RP1105
DYNAMIC
MIC
DOWN
5
6
MENU
7
UP
V O LU M E
3
4
CD PLAYER
RP1104
UP
22
MENU
DOWN
MENU
DOWN
UP
MENU
DOWN
Cat 5e/6
Multiple unit looping
ER1108
MATRIX O/RIDE
PANEL
AMP. FAULT
AMP. NUMBER
AMP. NORMAL
UP
AX 3800
ER1108
8 x8 M A T R IX M IX E R
M atrim ix P aging
MxP 2188
AMP. CHANGEOVER
1
2
CB110 MIC
AMPLIFIER ZONE 8
STANDBY AMPLIFIER
Equipment shown are for illustration of a full system. Some items may not be required
for simpler setup. Please consult us for larger system requiring multiple units in
cascade mode.
MxP2188
Matrix Components
amperes
RP1104 - Remote Zone Control Panel
RP1105 - Remote Source Input Panel
A remote zone controller with sensor touch buttons which allows the user to select
input music source, volume and tones. It shall be installed at remote location at
individual zone and connected to the MxP2188 controller via Cat5e / 6 UTP cable.
Each controller shall run individually to each input port of the respective zone.
It is used as a local source panel where microphone or line source from music player
can be patched to the controller. RP1104 Remote Zone Control Panel shall be installed
side by side with RP1105 to provide power source. The localized input source shall be
bypassed if emergency paging is activated at the controller. Among installations that
require RP1105 shall be promotion area at shopping centers, function rooms, etc.
Power source
Power consumption
Communication
Controls
Cabling
Distance
Dimensions (WxH)
Weight
24V DC via MxP2188
100 mA
RS485 ; 19.2 Kbps
Volume / BGM source / tone controls
Cat 5E / 6
Up to 500m
86 x 86 mm
100 g
Power source
Power consumption
Communication
Controls
Inputs
Cabling
Distance
Dimensions (WxH)
Weight
24V DC via MxP2188
100 mA
RS485 ; 19.2 Kbps
Volume
Mic or Line (unbal.), mini jack
Cat 5E / 6
Up to 500m
86 x 86 mm
100 g
ER1108 - Matrix Overriding
ER1108 is an 8 in / 8 out relay panel which would override all individual audio signal
from Matrix controller and re-route the outputs to a single emergency source such
as EP1200A emergency paging panel.
It is an optional item, and shall be installed after the Matrix controller with outputs to
individual amplifier of each zone. EP1200A shall be used with emergency trigger
and audio output connected to this unit.
PD1160 - 8/16 Zone Remote Paging Microphone
EX1103 - Paging Mic Extender
When multipoint paging is required, EX1103 shall be used, with each PD1160 connected
in series in a single circuit. The mic nearest to the Matrix controller shall have priority
over its precedence.
It is a simple and dedicated paging microphone for connection to MxP2188 MatriMix
system with 8 / 16 zones call station.
- Multipoint paging with EX1102 mic extender
- Direct connection to MxP2188 controller.
Power requirement
Power consumption
Zone selection
Data connection
Operating distance (data)
Audio distance
Indicators
Dimensions (WxHxD)
Weight
18
24V DC via MxP2188
800 mA
8 / 16 zone keys with ALL CALL
RJ45
300 m
300 m
Power, source, volume, busy
1.0 kg
23
Matrixmix MxP2288
8 x 8 Marix
Paging Controller
review
available in 2016
Introduction
Network
ready
Multiple Inputs
jacks
MxP2288 shall be another pride of Amperes, an all new successor of the popular
MxP2188. With a decade long experience in providing matrix solution to PA system, we
had incorporated various features and improving the shortcomings of the previous
version.
MxP2288 does not only offer simplified interconnectivity with its associated equipment
but minimizing equipment count for the similar functionalities. A summary of features
listed shall provide a better glimpse of what it can offer.
amperes
HTTP acces
PMX II LAN
compatible
Trusted throughout the years, Amperes will continue to deliver cost effective and
affordable solutions, uncompromising quality and reliability.
Simplified
setup
The new MxP2288 setting a new benchmark for matrix
paging installation.
FIRE
Matrimix Paging
8x8 MATRIX MIXER
MxP 2288
amperes
A simplified integration with EP1200A
Key Features
24
NETWORKING MADE AVAILABLE
As IT features are now inevitable part of PA system, MxP2288 is now ready with
network capability. It is now easier to install in IP environment for inter building
connectivity and not forgetting the remote viewing and controls the system. The
configuration tasks shall be conveniently managed via http.
FUTURE EXPANSION
With the host of features available for now and thoughts for thereafter, MxP2288
would be able to cater and upgraded for future needs. Firmware and software
would be easily updated when new functions are available, and we provide them
at no extra cost.
SYSTEM COST DOWN
Interfacing with EP1200A or adding a paging mic at rack has been simplified and
ER1108 is no longer required. Not only the interconnectivity links are reduced but
the number of accessories use, which is translated into cost reduction.
SMOOTH TRANSITION
Similarities for setup, operation and key features are carefully reserved in
MxP2288, enabling smoother transition from old to new.
AUDIO INPUT SOURCE
MxP2288 breaks the limitation on the input source connections and types. Now feel
free to insert any source, be it mic or line level, balanced or unbalanced.
MULTIPLE JACK AUDIO INPUT SOURCE
At times, audio source may have different output jacks, and we make it easier
for connections by providing combo jacks, which allow 1/4" phone jacks or XLR
Male for plugins.
CASCADING
Stacking up several controllers to larger setup is now a breeze. Cascading ports
are provided for the purpose and signal degradation is no longer an issue as every
link ports are now buffered. It means lesser cable mess and audio signal distributor
shall not be required.
INTEGRATION WITH PMX II LAN
Apart from webpage setting of various parameters, integration with PMX II LAN
would be made available for much easier access, control and monitor every
MxP2288 installed. User would be able to stream music directly from remote
PC, making the overall system truly flexible.
amperes
Technical Info
GENERAL TERM USED IN PUBLIC ADDRESS SYSTEMS
SOUND LEVEL COMPARISON CHART
ROOT MEANS SQUARE (RMS) :
Average value of ac voltage, it is 0.707 time of the peak voltage of a constant sine
wave.
IMPEDANCE (Ohm with symbol Z) :
A measurement of total resistance to current in a circuit with inductance and
capacitance, such as speakers and microphones. The value differs for different
frequencies, and thereby would normally be rated at Ohm @ 1 KHz.
Machine Gun
130
120
Power tools
Hard Rock Band
110
Heavy city traffic
Average Home Hi-Fi Level
90
Vacuum Cleaner
Average Automobile
70
SIGNAL TO NOISE RATIO ( S/N Ratio ) :
Measured in dB, is the ratio of signal to noise at same point of signal. It is normally
measured at 1 kHz with 1V input signal. Higher S/N ratio is always preferred.
Room with window air
conditioner
Average Home
50
DECIBELS ( dB ) :
Use to express the ratio between two signals, such as Voltage, Power, Current, etc.
It is expressed in dB SPL for Sound Pressure Level, dBV for relativity to 1V and
etc.
Quiet Conversation
Broadcast Studio
30
Human Breath
Anechoic Chamber
10
SENSITIVITY :
The minimum signal required for producing a fixed output level and is specified in
various terms. In Microphones ( mV/Pa), is amount of mV produced by a Pascal of
sound pressure ( 94 dB ) in axis with the transducer. In Speakers ( dB, 1W @ 1m )
is the sound output in dB produced by 1W of power and measured in axis of 1 m
away. In professional Amplifiers ( dBu or V ) is the input signal required for the
power amplifier to reach its rated output.
SOUND PRESSURE LEVEL ( SPL ) :
A measurement of loudness in relation to the threshold of human hearing at 2 uBar.
It varies with frequencies and thereby in audio, it is expressed as RMS value in dB
SPL. See also the SPL chart.
TOTAL HARMONIC DISTORTIONS ( THD ) :
Expressed in %, it is the ratio of a fundamental frequency to the level of all
harmonic frequencies produced by the equipment. Lower percentage is better.
FREQUENCY RESPONSE :
Is used to indicate how well an equipment or speaker response to the audio input
signal, usually 20 to 20 KHz. It is usually measured at 1KHz reference, 1V input
level with +/- 3 dB.
BALANCED SIGNAL :
Refers to cable carrying audio signal with 3 conductors ie. Hot, Cold and Ground
or Shield. It offers better immunity against external interference and is preferred
choice for long cabling.
UNBALANCED SIGNAL :
Refers to audio signal in cable with Hot and Ground (Shield) conductors. It is
recommended for short distance cabling as it is subjected to interference.
SPEECH TRANSMISSION INDEX ( STI ) :
STI is used to measure speech intelligibility by injecting a test signal at source point
and measurement is made at the listening plane. The measured value is within the
range of 0 to 1.
0
18
140
STI
0.3
0.45
0.6
0.75
1.0
100
80
60
40
20
0
Turbo Propeller Plane at
take-off
Threshold of pain thunder
Heavy Thunder
Subway
Banging Steel Plate
Alarm Clock
Average Factory
Background Music
Average Office
Voice, low
Quiet Home
Whisper
Watch Ticking
Threshold of hearing
0.0002 Dyne/Sq. cm
Sound Pressure Level ( SPL ) is normally expressed in dB, in
relation to the lowest sound level a human ear can hear ie.
20 uBar. The chart below shows typical SPL level from
various source of sound.
AUDIO LEVELS :
In professional audio, line level is referred to as +4 dBU which is a reference of how
much it is above or below the reference level of 0.775V. 4 dBU = 1.25V rms. The
value of consumer or semi-professional differs and is lower than this, eg. 0 dBV = 1 V
rms. Consumer line level is typically -10dBV or 0.32V.
0.775V rms is used as reference as it is used to generate 1 mW ( 0 dBm ) over the
load of 600 Ohms. ( P = V2 / R ).
TERMS RELATED TO SPEAKER POWER
AVERAGE POWER :
Often referred to RMS Power as rms value of voltage and currernt are used to
calculate the power.
PROGRAM POWER :
Also known as Music Power and is normally twice the amount of Average Power. It is
used to select suitable amplifier rating.
PEAK POWER :
Defines the instantaneous power delivered to speaker at highest level of output.
25
DA2208
Distribution Amplifier
amperes
Introduction
DA2208 shall be used to amplify incoming audio signal of line level and thereafter
linked to several amplifiers to avoid sound distortion. It consists of 2 sets of 1 in 4
out configuration and can be set as 1 in 8 out format. Each output channel has its
individual bass and treble controls, facilitating tone setup of the amplifier to suit the
type of speakers used as well as the acoustic environment.
Rear View:
Dual Mode
Tone Controls
Features
Operates as dual channel 1 input 4 output or single channel 1 input 8 output
Individual bass and treble control with volume adjustment
Direct input signal to output whenever DC power input not available or
whenever power failure occurs
Operating voltage
Power consumption
Configuration
Input level
Input impedance
Output gain
Output impedance
Controls
Frequency response
Dimensions (WxHxD)
Weight
24V DC
2.4W
1 in x 8 out or 2 in x 4 out
Line : 1V rms max
10 K Ohm
+ 4 dBu
10 K Ohm
Bass, Treble, Channel volume
150 ~ 19 KHz (+/- 3 dB at 1 KHz)
482 x 44 x 180 mm
1.55 kg
MX2222 MIXER
Paging audio
signal ( Bal )
BGM audio
signal ( Bal )
DA2208 DIST. AMPLIFIER
Balanced
output
Amplifiers for signal
input 1 with output
from Ch 1 to 4,
Serves as Paging
amplifiers
PA 2120
1 20 W atts
POW ER
POW ER
PA 2120
I
PROTECT
O
S IG N A L -1 0 dB
C LIP
S IG N A L -4 0 dB
AMP ( PAGING )
PA 2120
1 20 W atts
POW ER
POW ER
PA 2120
Amplifiers for signal
input 2 with output
from ch. 5 to 8
Serves as BGM
amplifiers
I
PROTECT
O
S IG N A L -1 0 dB
C LIP
S IG N A L -4 0 dB
PA 2120
1 20 W atts
POW ER
POW ER
PA 2120
I
PROTECT
O
S IG N A L -1 0 dB
C LIP
S IG N A L -4 0 dB
AMP ( BGM )
PA 2120
1 20 W atts
POW ER
POW ER
PA 2120
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.15 kg
26
I
PROTECT
O
S IG N A L -1 0 dB
C LIP
S IG N A L -4 0 dB
The above illustration is for Uninterrupted Paging setup. In normal setup with single
input, use the link switch to form 1 input 8 outputs configuration. Each output from
DA2208 can be linked up to 6 power amplifiers.
MX2222
Pre-Amplifier Mixer
amperes
Introduction
Priority Mute
Dual Output
Phatom Power
Features
12 inputs of mic, BGM sources, ext.chime and mixer link
Expandable to form more channels for larger setup
Auto mic muting with adjustable mixing level for mic Ch.1, 2, ext.chime and
mixer link
This compact 1 hu pre-amplifier mixer features 6 mic, 4 BGM sources, chime and
external line inputs and is suitable for any application, such as meeting room, lecture
theatre, hall of prayer and definitely commercial fixed PA installation.
It dual output feature can be used for uninterrupted paging setup, ie. BGM and paging
announcement. Adjustable priority muting level is available for paging announcement to
override BGM and other lower priority sources. Adjusting it to minimum and the unit shall
work like any other mixing unit and it comes with 12V phantom power supply for mic
input 1 to 4.
PM1000
MICROPHONE
Priority muting with disable option for normal mixing mode
Switchable phantom power for mic channel 1 to 4
Dual output ; mixed line and BGM output for uninterrupted paging setup
PM1060
MICROPHONE
AUDIO SOURCES
Independently adjustable BGM output level with balanced line
MX2222
OFF
Built in daisy chain source selector with last selection memory
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
TUNER
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
to ZS
remote trigger
AC and DC operation for uninterrupted operation during power failure
MAX
MIN
MAX
SIG IN
MIN
MAX
SIG IN
MIN
POWER
TONE CTRL
OFF
MIN
MIN
Bass and treble tone control
SELECT
MASTER
EXT INPUT
MX 2222
MAX
MAX
CHIME
SIG IN
MIN
CASS
CD
AUX
MAX
MIXER
TREBLE
BASS
MIN
MAX
SIG IN
MUSIC SOURCE
line out
(mixed)
line out
(BGM)
MIC
TEST
SIREN ACTIVATE
AM 6000
POWER
FIRE
EP1200
AMPLIFIER - BGM
line
PA 2120
120 Watts
POWER
POWER
PA 2120
Technical Specification
I
PROTECT
O
SIGNAL -10 dB
CLIP
SIGNAL -40 dB
AMPLIFIER - PAGING
PA 2120
120 Watts
POWER
POWER
Operating voltage
Power consumption
Input channels
Input impedance
Sensitivity(1.2 mVrms output)
Output level
Output impedance
Controls
Phantom power
Frequency response
S/N ratio
Dimensions (WxHxD)
Weight
230 / 240V ac or 24V DC
2.4W on 240V ac / 100 mA on 24V DC
6 x mic ; 4 x BGM ; ext chime in ; mixer link
Mic : 600 Ohm
BGM : 47 K Ohm unbalanced
Chime input : 10 K Ohm unbalanced
Mixer link : 600 Ohm balanced
Line : 530 mVrms
Mic : 2.5 mVrms
1.2V XLR balanced (mixed output)
1.0V phone jack balanced (BGM output)
600 Ohm balanced
Mic channel ; chime ; mixer input
Master mixed ; BGM ;
Bass and treble controls
12V DC switchable at mic 1 to 4
175 - 15 KHz (+/- 3 dB at 1 KHz) with low cut
> 60 dB at 1 KHz
482 x 44 x 180 mm
2.5 kg
PA 2120
I
PROTECT
O
SIGNAL -10 dB
CLIP
SIGNAL -40 dB
zone remote
trigger fr paging
mic
ZONE SEL
ZS5602
paging
BGM
TO SPEAKERS
Illustration for uninterrupted paging system.
Rear View
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 3.1 kg
27
PA300 Series
Mini Amplifiers
Power Amplifiers
amperes
20W 4 Ohm Mini Amplifier | PA320
30W 100V Line Amplifier | PA330
Introduction
Amperes PA320 is a mini amplifier used to amplify BGM signal to a speaker of 4 or 8
Ohm, such as from TV output to a bathroom speaker in a hotel room. Amperes
VC7805 volume controller and VP7810 BGM-Speaker patch panel can be installed if
required to allow emergency paging to be announced at the speaker.
Other applications include simple mic calling system at counters or as an amplifier
module to some other system which need to broadcast audio output to a speaker, ie.
queue management system or telephone intercom.
Features
PA320
Available in 20W 4 Ohm rating or 30W 100V line (PA330)
Adjustable volume control for volume preset
Compact size for easy installations
24VDC Overriding
(optional)
PA320
8 Ohm
Output
SPEAKERVOLUME
2
1
OFF
3
4
5
OVERRIDE
amperes
20W 4 OHM
Audio
VC7810 8 OHM
VOLUME CONTROLLER
VP7810
OVERRIDING
UNIT
230 / 240V ac
TV WITH
AUDIO OUTPUT
BATHROOM SPEAKER
(8 OHM WITHOUT
TRANSFORMER)
PA330
Amperes PA330 has higher rating of 30W 100V line which accepts unbalanced line
input. It can be used as remote amplifier in a decentralised PA system. Among applications include classroom paging and paging for remote station.
Packing information
PA320
WxHxD
: 560 x 165 x 295 mm
Weight
: 16.4 kg
Using LC1000 (step down module) shall allow PA330 to accept 100V line input and
thereby a very large network of paging can be implemented in a wider area.
PA330
WxHxD
: 560 x 430 x 225 mm
Weight
: 24.1 kg
Rating
Operating voltage
Current consumption
Input signal
Input sensitivity
Max input
Input impedance
Frequency response
Controls
Dimensions (WxHxD)
Weight
28
PA320
20W 4 Ohm
0.14A
230 ~ 240V ac
PA330
30W 100V Line
Mono ; unbalanced line
40 mV
1.2V
0.17A
10 K Ohm
100 K Ohm
150 ~ 15 KHz
100 ~ 18 KHz (+/- 3 dB)
Input volume preset
160 x 95 x 170 mm
130 x 55 x 95 mm
2.4 kg
790 g
Power Amplifiers
125W 100V
250W 100V
375W 100V
500W 100V
Introduction
QP Series are available from 125W to 500W 100V line in 2 hu height, with enhanced circuitry
for higher efficiency, better frequency response and with extra protection features. It is
digitally controlled and thus enable the unit to be monitored and controlled remotely via
RS485. They can be linked to PMX II Xtended* software for remote setting and monitoring,
enabling control flexibility for the user.
POW ER
MX2222
MIXER
I
|
|
|
|
audio
signal
QP2000
DUTY AMPLIFIER
POW ER
M ENU
Q P2500
I
O
UP
O
QP2125
QP2250
QP2375
QP2500
QP2000 Series
Power Amplifier With AFS
amperes
DOW N
5 0 0 W 1 0 0 V L IN E P O W E R A M P LIF IE R
M ENU
M AX
M IX ER
M IN
E XT IN P U T
MAX
M IN
UP
DOW N
M IN
100V Line
Standby
Output
S IG IN
POW ER
UP
S IG IN
CH4
I
O
MAX
M IN
M ENU
Q P2500
MAX
M IN
CH5
MAX
S IG IN
CH6
MAX
M IN
100V
S IG IN
SOURCE
I
O
C H IM E
M AX
T R E BLE
TON E CTRL
B A SS
M IN
M A S TE R
S IG IN
MAX
OFF
OFF
TUNER
CD
CASS
S ELEC T
AUX
100V
POW ER
Q P2500
S IG IN
MAX
M IN
CH3
DOW N
M IN
MX 2122
S IG IN
CH1
MAX
M IN
CH2
100V
S IG IN
Inputs
Another distinctive feature is its Auto Fault Sensor ( AFS ) circuitry which auto detects faulty
output of the unit and would enable a dry contact to initiate an alarm for fault. The internal
Fault Standby Changeover relay would allow a faulty unit to be taken over by a standby
amplifier if one of the duty amplifiers failed. A feature that reduces the equipment count in the
system as well as reducing cabling complexity.
POW ER
M ENU
Q P2500
I
O
UP
DOW N
STANDBY AMPLIFIER
Features
Available in 125 / 250 / 375 / 500W 100V line output in compact 2hu height
Remote Zone
Control
SPEAKER
ZONE
SELECTOR
ZS 5121
O V E R R ID E
1
2
3
4
5
6
7
SPEAKER ZONE SELECT
8
9
10
11
12
ALL
CALL
Digital setting for various control features such as bass, treble, fan speed, etc
Built in Auto Fault Sensor and Changeover relay for standby fault changeover
TO SPEAKERS
RS485 data port for remote monitoring
Fan speed option ensures longer lifespan of the unit
Overload, thermal cut off, short circuit and fuse protections
High efficiency for lower power consumption and lesser back up battery
capacity
Packing information
WxHxD
: QP2125 / QP2250 / QP2375 / QP2500
: 550 x 180 x 465 mm
Weight
QP2375
QP2250
230 / 240V ac or 24V DC back up supply
580VA (2.4A)
290VA (1.0A)
440VA (1.8A)
20A
8A
15A
0.32A
0.3A
0.31A
1V / 10 K ohm; balanced via XLR female
-40 to 0 dB
375W
125W
250W
38.7V
22.3V
31.6V
27 Ohm
80 Ohm
40 Ohm
70 Hz - 15 KHz @ 1 KHz +/- 3 dB
>70 dB @ 1 KHz, 1V
<0.18 %
Thermal, Short circuit, Overload, Fuse
75 Deg C
Auto temperature controlled fan speed with auto on
LCD with temp, audio level and address
RS485, 19.2 kbps
Internal Pilot Tone, Detection at 15 to 25 secs at 10 secs intervals
Standby amplifier relay activation, fault dry contact
482 x 88 x 335 mm
16.5 kg
12.3 kg
13.5 kg
QP2125
Power requirement
Power consumption (240V ac)
Current consumption (24VDC)
Standby current (24VDC)
Input signal
Input gain control
Rated output (100V, RMS)
4 ohm output voltage
Output impedance (max load)
Frequency response
S/N ratio
THD + N
Protections
Cut off temperature
Cooling system
Indications
Communication
Fault sensing
Fault detection response
Net Weight
: QP2125
QP2250
QP2375
QP2500
-
13.7 kg
15.0 kg
18.0 kg
20.2 kg
QP2500
720VA (3A)
25A
0.35A
500W
44.8V
20 Ohm
18.8 kg
29
PA2000 Series
amperes
Power Amplifiers
120W 100V
240W 100V
360W 100V
480W 100V
Introduction
|
|
|
|
PA2120
PA2240
PA2360
PA2480
Features
PA2000 Series of amplifiers had been a reliable workhorse for years and had been
refined to perform more efficiently. It is available with power ratings of 120W to 480W
100V line, in 2 HU height for space saving.
Various protection features are included with the objective of providing trouble free
operation for years to come.
Available in various ratings ; from 120W to 480W 70 or 100V line
4 Ohm speaker connection available with 25V output
Thermal protection by muting input signal (typically 85 deg at heat sink)
Momentary short circuit protection
Temperature dependent dual speed cooling fan
Balanced input signal with gain control and selectable grounding option
AC and DC operation for uninterrupted operation during power failure
Packing information
WxHxD
: PA2120 / PA2240 / PA2360 / PA2480
: 550 x 180 x 465 mm
Weight
: PA2120
PA2240
PA2360
PA2480
-
13.4 kg
14.6 kg
17.4 kg
19.4 kg
From pre-amplifier
Loop to next amp in.
24V DC
battery backup
Output to
speakers or zone
selectors
parallel to next
amplifier
Power requirement
Power consumption (240V ac)
Current consumption (24V DC)
Standby current (24V DC)
Input signal
Input gain controls
Rated output (100V, RMS)
4 Ohm output voltage
Output impedance (max load)
Frequency response
S/N ratio
THD + N
Protections
Cut off temperature
Cooling system
Indications
Dimensions (W x H x D)
Net Weight
30
PA2120
280VA (1.3A)
8A
0.2A
120W
22V
83 Ohm
12 kg
PA2360
PA2240
230 / 240V ac or 24V DC back up supply
560VA (2.3A)
420VA (1.75A)
19A
14.5A
0.3A
0.25A
1V / 10K Ohm; balanced via XLR female
-40 to 4 dBu
360W
240W
38V
31V
27 Ohm
42 Ohm
70Hz - 15 KHz @ 1KHz +/-3 dB
>70 dB @ 1 KHz, 1V
<0.18 %
Thermal, Short circuit, Overload, Fuse
75 Deg C
Auto temperature controlled fan speed
LED : Power, Signal level
482 x 88 x 335 mm
16.2 kg
13.3 kg
PA2480
700VA (3.0A)
24A
0.32A
480W
43.8V
20 Ohm
18.2 kg
DP2000 Series
Power Amplifiers
Multi Channel Power Amplifiers
amperes
DP2406 | 4 Ch 60W 100V Multi Channel
DP2212 | 2 Ch 120W 100V Multi Channel
Introduction
D
DP2406 is a quad channel with power rating of 60W 100V line per channel whereas
DP2212 is dual channel of 120W 100V line per output. With its Class D amplification, it
has various advantages over conventional power amplifiers, notably its higher power
efficiency, lesser heat dissipation as well as flatter frequency response.
It is most suitable for Matrix setup, which multiple channels of amplifiers are required and
with lesser unit count of amplifiers, it translates into more rack space savings and lower
overall setup costs.
High Temperature
Operating
Multichannel
Class D
Features
Class D amplifiers for wider frequency response
Low power loss with higher efficiency circuits
Rear View DP2406
Available in 2 x 120W or 4 x 60W 100V Line
High ambient temperature operating condition
AC and DC operation
Rear View DP2212
Multiple Input Sources
MxP2288
DP2406
DP2212
Rating
4 x 60W 100V line
2 x 120W 100V line
Operating voltage
230 ~ 240V ac / 24V DC
Current consumption
1.4A on 240V AC
Current (Load / Standby)
10.2A/0.7A on 24V DC
Input
4 x XLR
2 x XLR
Input level
1.25 Vrms Balanced
Outputs
100V, 70V, 30V
Frequency response
100Hz ~ 16kHz + / - 3 dB
Thermal, short circuit AC & DC fuse
Protection
Power, audio input level, over temperature, amplifier faulty
Indicator
Via continuous operating fan
Cooling system
Dimension (WxHxD)
482 x 88 x 335 mm
Weight
13.3 kg
12 kg
MxP 2288
DP2406
DP2212
3
4
DP 2406
1
2 x 120W POWER AMPLIFIER
2
3
4
SPEAKER
5
6
Packing information
WxHxD
: DP2212 / DP2406
: 550 x 180 x 465 mm
Weight
: DP2212 - 13.7 kg
DP2406 - 15 kg
31
MA2000 Series
Mixer Amplifiers
Power Amplifiers
amperes
60W 100V Mixer Amp With 3 Zone Output | MA2060
Introduction
MA2000 Series, available in power rating of 60 to 240W 100V line is suitable for small
setup such as showrooms, shops, function rooms or small mosques. It has 3 selectable
zone outputs with remote selection from PM Series of paging microphones with muting
feature.
FRONT INP
MICROPHONE
DYN.MIC
Optional media player module for USB / SD Card MP3 playback and AM FM tuner is
available for 240W version with prefix P (MA2024P).
ON
LINE
MIC
LINE
MIC
LINE
MIC
LINE
MIC
REMOTE
MIC
Line output to extend to
booster amplifier
SPEAKERS
Features
Z1
CD1001
CD 1001
Z2
I
O
VOL CTRL
6 mic / line selectable input channels, with front mic jack, phantom power
Priority muting for mic input 1 with adjustable muting level
3 zone speaker output with ALL CALL and remote triggering port
100V line output with aux 4 Ohm speaker terminal
Tone and bass controls
Z3
AC / DC operation
Variants :
MA 20xx / P : with USB / SD card / FM tuner player
MA Series is available with optional media player module
Ratings
Operating voltage
24V DC requirement
Input channel
Input phantom power
Input sensitivity / impedance
Tone controls
Outputs
Output selection
Frequency response
Protections
Indicators
Cooling system
Dimensions (WxHxD)
Weight
32
Packing information
WxHxD
: MA2060 / MA2012
: 550 x 180 x 430 mm
Weight
: MA2060 - 11.0 kg
: MA2012 - 12.1 kg
: MA2024 - 14.0 kg
MA2060
60W 100V line
MA2012
MA2024
240W 100V line
120W 100V line
230 ~ 240V ac / 24V DC
4A
8A
15A
1.3A / 0.4A
2.2A / 0.4A
6.1A / 0.3A
6 : 2 MIC ( XLR), 4 MIC/Line Selectable (RCA/Phone Jack)
Mic 1 and 2 ; 12V DC
2 x Mic (XLR) & 4 x Mic
2 x Mic (XLR) & 4 x Mic
(Phone jack) : 20 mVrms
(Phone jack) : 4 mVrms
4 x LINE (RCA) : 150 mVrms
4 x LINE (RCA) : 350 mVrms
Bass (100 Hz) ; Treble (10 KHz) +/- 3 dB
3 Zone 100V line, 4 Ohm
Front and remote triggering
175 ~ 18 KHz
70 ~ 15 KHz
Thermal, short circuit, AC and DC fuse
AC mains, clip, protect, audio input level
Dual speed fan with heat sensing
424 x 88 x 300 mm
9.8 kg
10.9 kg
12.8 kg
33
Basic Mixing Amplifiers
amperes
MC2000 Series
Power Amplifiers
MC2106 | 60W 100V Mixer Amp
MC2112 | 120W 100V Mixer Amp
IMPROVED
Features
Introduction
MC2000 Series offer simple mixing amplification for small setups or functions such as
shops, boutiques, meeting rooms or a small gathering venues. Two versions are
available ; 60 and 120W 100V line outputs.
Though being basic, it is equipped with various protection features such as thermal and
short circuit protections.
6 inputs for mic and line with phantom power for input 1
Tone and bass controls
70 / 100V line output with 4 Ohm terminal with audio line output
Short circuit, thermal protections
Rear View:
8 OHM SPEAKERS OR
100V SPEAKER WITH
MATCHING TRANS
PAGING
MIC
I
O
CD1001
CD 1001
CD 1001
Packing information
WxHxD
: MC2106 / MC2112
: 560 x 165 x 295 mm
Weight
: MC2106 : 7.80 kg
: MC2112 : 8.65 kg
stereo
DYNAMIC / COND.
MICROPHONE
I
O
MC2106
Rating
Operating voltage
24V DC requirement
Input channel
Input phantom power
Input sensitivity @ 1W / 4 Ohm
Tone controls
Outputs
Frequency response (± 3dB @ 1Kz 20 ~ 20 KHz )
SNR
THD+N (at rated power)
Protections
Indicators
Cooling system
Dimensions (WxHxD)
Weight
MC2112
60W 100V line
120W 100V line
230 ~ 240V AC mains
1.2A / 0.1A
2.2A / 0.1A
6 inputs; 4 Mic phone jack, 2 line selectable (RCA)
Mic 2 : 12V DC
Mic : 430 mV
Line : 650 mV
RCA : 642 mV
Bass (150 Hz) ; Treble (10 KHz) ± 3 dB
4 Ohm / 100V line
120 Hz - 15 kHz
76 dB @ 1 kHz, 1V
0.02%
Thermal, short circuit, AC and DC fuse
Power, Audio Input Level
Fan with dual speed
424 x 88 x 180 mm
7.05 kg
7.80 kg
33
Technical Info
amperes
SPL (dB) TO POWER AND DISTANCE
The Sound Pressure Level ( SPL ) shall drop 6 dB
whenever the distance from source is doubled. It can
be calculated from the formula :
Distance (m) 2 4 8 10 15 20 30 40 50 60 80 100
dB Loss
6 12 18 20 23.5 26.0 29.5 32 34 35.6 38 40
SPL drop = 20 log D ( D= distance in metre )
SPL ( dB ) shall increase 3 dB when the power to
speaker is doubled, calculated from :
Power (W)
dB Increase
SPL = 10 log W ( W = power input )
SPEAKER CABLING IN 100V
LINE SYSTEM
Cables used in PA installations are
subjected to losses as similar to the
cablings in electrical installations. The
factors affecting the percentage loss
include the cable size, length, cable
materials, input voltage, load and tempera
ture. A typical loss chart with relation to
cable size is shown below. ( Copper
conductors in single phase ). For accuracy,
please refer to the manufacturer’s data
sheet.
1
2 4
8 10 15 20 30 40 50 80 100
0
3 6
9 10 11.8 13 14.8 16 17 19 20
Length in Meter for 0.5 dB Power Drop (Appr 81% at Load )
Cable Gauge Conductor Size Impedance
AWG
( mm sq )
Ohm / 1000ft
10
5.26
1.00
11
4.17
1.26
12
3.31
1.59
13
2.62
2.00
14
2.08
2.53
15
1.65
3.18
16
1.31
4.02
17
1.04
5.06
18
0.82
6.39
125W power
250W
500W Load
20 Ohm
190
150
120
90
75
60
45
35
26
500W
1 dB loss
3 dB loss
1 dB loss
3 dB loss
1 dB loss
3 dB loss
12
1727
1087
6045
3805
862
542
3017
1897
429
270
1502
945
14
683
2391
341
1194
170
595
16
430
1505
215
753
107
375
18
269
942
134
469
67
235
10
Total
Impedance
800 Ohm
400 Ohm
300W Load
33 Ohm
320
260
200
160
130
100
70
60
50
200W Load
50 Ohm
490
390
310
240
190
150
110
90
70
100W Load
100 Ohm
990
780
620
490
390
310
240
170
150
50W Load
200 Ohm
1990
1580
1250
990
780
620
480
390
310
The table provides an approximate cable length permissible for
specified loss of signal in 100V line speaker installation.
200 Ohm
FIBER OPTIC CABLES IN PA INSTALLATIONS
Laying of copper cables may not be wise in installations such as railway stations communications, sparsely located buildings or remotely located paging points. They may pose
hazards like lightning strike, inteferences as well as signal drop, and thus affect the performance and lifespan of the installation.
Fiber optic cabling is an alternative solution and applying IP to the system would make the PA setup to be cost effective, safer, expandable and more efficient.
Followings are the items required for fiber optic installation :
IP PA Server / Controller - Amperes iPX5101 ( one per system )
IP PA Client / Adaptor - Amperes iPX5151 ( one for each location )
Network Switch, 10/100T or higher
Cat 5e to Fiber Converter ( if Fiber optic network switch unavailable )
Fiber optic cable ( Single / Multimode ) - 2 core
For short distance ( typically around 2 km ) multimode cable shall be used and single mode type for longer distance.
34
6 Duty / 1 Standby Changeover Panel
amperes
AX700 / AC3601
Changeover & Monitoring
AX700 | 6 Duty / 1 Standby Amplifier Changeover Panel
AC3601 | 6 Duty / 1 Standby Manual Changeover Panel
Introduction
Features
AX700 is a platform for standby amplifier to take over failed duty unit in an
automated changeover setup. Each unit caters for 6 duty and 1 standby amplifier but
expandable to larger setup with a single standby power pack.
It shall be used with amplifier with auto fault sensing (AFS) such as QP series and
whereas normal amplifiers are used, Amperes AS4000 shall be installed at every
duty unit.
AX700 has protection feature that only allows a single takeover to prevent
overloading.
Cater for 6 duty and 1 standby amplifier
Expandable for 1 standby to serve more than 6 duty units
Overload protection by allowing only a single take over
Prioritized changeover - unit with higher number is preferred for changeover
Fault alert with LED indicator and switchable buzzer
Compatible with most auto detection cards
AX700s
6 Duty / Standby Amplifier
Changeover Panel
AC3601
6 Duty / 1 Standby Manual
Changeover Panel
Amperes AC3601 is a manual changeover panel for 6 duty with 1 standby amplifier and
is required for a standby unit to take over a failed duty amp to ensure uninterrupted and
continuous operation of a PA system. More than one AC3601 can be cascaded for a
single standby unit to cater for more than 6 duty packs.
Protection circuitry is embedded that only allows one failed duty amplifier to be taken
over by standby unit to prevent overloading. Priority features shall ensure higher
numbered failed unit has preference for changeover.
Features
Cater for 6 duty and 1 standby amplifier
Expandable for 1 standby to serve more than 6 duty units
Overload protection by allowing only a single take over
Prioritized changeover - unit with higher number is preferred for changeover
Manual front panel changeover selection
IN
P L E AS E O B S E R V E P O L A R IT Y
OUT
HOT
HOT
S TA N D B Y
A M P INP U T
COM
COM
COM
HOT
HOT
HOT
COM
COM
HOT
COM
HOT
HOT
COM
HOT
COM
COM
COM
DU TY A M P L IF IE R INP U TS
HOT
6
HOT
5
HOT
4
COM
3
COM
2
COM
1
S/BY
+
COM
A M P .F A U LT DE TE C T TR IG G E R
D C 24V
0 .5 A
HOT
AUTO AM P. C HAN G E OVE R
Rear View AX700 :
A M P.IN
A M P .O U T
S /B Y IN
D U TY A M P
S/B Y A M P
IN
OU T
L IN K TO A S4 0 0
TO ZON E SELEC TO R
OR SPEA KERS
AX 7 0 0 W IR IN G C O N N E C T IO N S
AM P . IN - FR . AM P O U T P U T S
AM P . O U T - T O Z O N E S E L E C T O R / S P E A K E R S
M AX L O AD / C H - 4 0 0 W / 1 0 0 V L IN E
LIN K
COM
TO
A S4 0 0 1 ~ 6
DE TE C T
Q u a lit y P ro d u c t Fro m
A M P E R E S E LE C T R O NI C S
A X7 0 0
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.5 kg
Rear View AC3601 :
IN
OUT
HOT
S TAN D B Y C AS C AD E
LIN K
AM P I N PU T
COM
HOT
COM
COM
HOT
HOT
COM
COM
HOT
COM
HOT
COM
HOT
HOT
HOT
COM
COM
COM
HOT
HOT
HOT
COM
COM
HOT
COM
AC 3601
D U TY AM PLIFIER IN PU TS
DC 24V USAGE OF NON RECOMMENDED
POWER SUPPLY UNIT MAY CAUSE
DAMAGE TO THIS EQUIPMENT
DC SUPPLY RATING :
24V DC, 0.5A
+
( PS9400 RECOMMENDED )
WIRING CONNECTIONS
LINK IN - FR. N-1 AC3601
LINK OUT - TO NEXT AC3601
MAX LOAD / CH - 400W / 100V LINE
PLEASE OBSERVE POLARITY
IN
L IN K O UT
D UT Y A M P
S/ B Y A M P
AMP.IN
AMP.OUT
S/BY IN
TO ZONE SELECTOR
OR SPEAKERS
AC3601
another quality product from
a m p e re s e le ct r o n ics
AX700
Operating voltage
Power consumption
Zone load rating
Amplifier inputs
Indications
Switching mode
Changeover alert
Changeover section
Cable connection
Cable size
Dimensions (WxHxD)
Weight
AC3601
24V DC via PS9400 PSU
Standby : 82 mW, 3.4A
Operating : 1.3W, 50 mA
500W / 100V line per ch.
6 Duty / 1 Standby
Front switch LED
Red LED for take over
Green - normal / non c/over
Dry contact activation by AS4000
Via front panel switch
Buzzer, LED
Amplifier outputs only
Plug in connectors
2.5 mm sq
482 x 44 x 180 mm
2.0 kg
35
AX3800
8 Duty 1 Standby Auto Amp. Changeover Panel
amperes
IMPROVED
Introduction
AX3800 offers great flexibility and simplicity for amplifier fault changeover setup. With
the precise circuit design, amplifier fault detection period is greatly reduced to initiate
timely changeover to standby unit. The internal pilot tone generation at 20KHz is set at
optimum interval to avoid unnecessary loading to amplifiers.
Changeover shall occur at both input and output of amplifiers, making it suitable for
application in a matrix system. Priority and single changeover ensures overloading of
standby amplifier is avoided, thus providing a reliable and uninterrupted system at most
times.
20KHz
Simplified Cabling
Pilot Tone
Generator
Shorter Fault
Detection
Features
Cater for 8 duty and 1 standby
Expandable for 1 standby to cater for more than 8 duty amps.
Built in Pilot Tone generator, transmit at intervals and senses at sequence to
protect amplifiers
Rear View:
Overloading protection by allowing only a single take over
Prioritised changeover which higher numbered amplifier shall be preferred for
take over if more than two units are down
AUDIO SIGNAL INPUTS / OUTPUTS
-
+
-
G
+
-
CHANNEL 2
SIGNAL
LINK
INPUT
OUTPUT
LINK OPEN
+
-
G
+
-
STANDBY FAULT
CONT.
OUTPUT
3A NO
MAX
- G
+
CHANNEL 1
SIGNAL
LINK
INPUT
OUTPUT
LINK OPEN
OUTPUT
+
LINK OPEN
-
INPUT
G
+
-
STANDBY
AMP
Shorter fault detection time from 7 to 15 seconds
CASCADE RS 485
CHAN. 1
ON
CHAN. 2
ON
CHAN. 3
ON
CHAN. 4
ON
CHAN. 5
ON
CHAN. 6
ON
CHAN. 7
ON
HIGH
IN-
IN+
+
CHANNEL 3
SIGNAL
LINK
INPUT
G
CHAN. 8
ON
LOW
CHANNEL 1
-
IN+
CHANNEL 2
OUT+
CHANNEL 4
OUTPUT
LINK OPEN +
IN-
-
OUT+
+
OUT-
G
OUT-
IN-
IN+
-
IN-
CHANNEL 3
OUT+
IN-
+
SIGNAL
LINK
INPUT
OUTPUT
LINK OPEN
IN+
-
CHANNEL 4
IN+
IN-
IN+
OUT+
CHANNEL 5
+
CHANNEL 5
SIGNAL
LINK
INPUT
G
OUT+
-
OUT-
+
OUT-
CHANNEL 6
OUTPUT
LINK OPEN
OUT-
-
CHANNEL 6
IN +
CHANNEL 7
+
IN -
G
OUT -
IN+
IN-
OUT-
OUT+
CHANNEL 8
DC 24V
0.5 A
+
-
-
SIGNAL
LINK
INPUT
OUTPUT
LINK OPEN +
OUT +
-
IN+
+
CHANNEL 7
SIGNAL
LINK
INPUT
G
IN-
-
OUT+
+
OUT-
CHANNEL 8
OUTPUT
A
B
ON
SWITCH TO OFF FOR UNUSED CHANNEL
CHANNEL / AMP. DETECTION SWITCHES
Changeover at input and output section simultaneously ; suitable for matrix
system installations
Input link switch ; making connection of sources easier
Channel isolation switch for unused or un-monitored channel
DUTY AMP
PA 2120
DUTY AMP
PA 2120
PA 2120
I
O
POWER
I
O
I
O
POWER
POWER
STANDBY
AMP
Individual channel status indicators ; normal, fault and changeover
SIGNAL -40 dB
SIGNAL -10 dB
CLIP
PROTECT
POWER
SIGNAL -10 dB
CLIP
SIGNAL -40 dB
PROTECT
POWER
CLIP
SIGNAL -40 dB
SIGNAL -10 dB
PROTECT
POWER
100V
120 Watts
PA 2120
120 Watts
PA 2120
120 Watts
PA 2120
audio +
PT
INPUT SOURCES
OFF
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
TUNER
MAX
MIN
SIG IN
MAX
MIN
MAX
SIG IN
MIN
MAX
SIG IN
MIN
MAX
SIG IN
MIN
SIG IN
MAX
MIN
MAX
MAX
CHIME
MIN
AX 3800
TREBLE
POWER
AMP. FAULT
1
2
3
4
5
6
7
8
PILOT TONE
STANDBY AMP. FAULT
amperes
24V DC
overriding
1
amperes
2
3
4
5
6
7
SPEAKER ZONE SELECT
8
9
10
11
12
ALL
CALL
24V DC
overriding
SPEAKERS
ZONE
SELECTOR
VOL
CTRL
Cascade AX3800 if more than 8 duty
amps are installed
36
O
AUX
MAX
MUSIC SOURCE
FIRE
AX3800
6
1
MIN
SIG IN
E/M
PANEL
ZS 5121
OVERRIDE
BASS
MIC
SIREN ACTIVATE
AMP. NORMAL
AMP. NUMBER
AMP. CHANGEOVER
100V
1
6
100V
I
CASS
CD
MAX
MIXER
SIG IN
TEST
AM 6000
POWER
TONE CTRL
OFF
MIN
MIN
SIG IN
audio
SELECT
MASTER
EXT INPUT
MX 2122
Operating voltage
Power consumption
Input signal
Input impedance
Audio output gain
Pilot tone interval
Pilot tone frequency
Detection line
Detection level
Failure detection time
Failure recovery time
Zone load rating
Status indication LED
Changeover alert
Changeover section
Dimensions ( WxHXD )
Weight
24V DC ; 1A
6.8 W
8 Ch balanced line signal
10 K Ohm
Unity
8 seconds / channel
20 KHz ( +/- 5% )
70 / 100 V line
50 V rms min
7 - 15 seconds
20 seconds max
500W / 100V line max
Normal ; Fault ; Changeover
Buzzer with switch
Input and output simultaneously
482 x 88 x 180 mm
2.85 kg
Packing information
WxHxD
: 560 x 165 x 295 mm
Weight
: 3.6 kg
amperes
6 Ch Speaker Line Surveillance
Introduction
Features
6 channel speaker line monitoring and expandable
LS4600 provides reliable speaker circuit monitoring for ground leakage, short and open
circuit at user settable intervals. Impedance measurement method is used in determining
the health of the circuit, thus giving flexibility over cabling routings.
Basic and Advance level of detection setup
Detection of faulty cable and speaker in individual zone or circuit
It is loaded with features that would enable the device to be fitted to any PA installations
with different requirements of setups.
Impedance measurement method - no capacitor coupling required and cable
branching allowed.
Faulty circuit disconnection option
Operating voltage
Power consumption
Capacity
Processor
Impedance detection range
Power measurement range
Measurement accuracy
Pilot tone injection frequency
Pilot tone signal output level
Transmittal detection period
Detection interval
Sensitivity setting
Indicators - LED
Display LCD
Audible output signal
Dry contact setting
DC output in detection mode
Dimensions (WxHxD)
Weight
LS4600
Built in impedance meter, range within 10 Ohm to 10 K Ohm
LCD display to facilitate system setup, measurement and monitoring
3.5W
6 channel and expandable
PIC micro controller with 12 bit ADC
10 to 10 K Ohm
3 to 1000W 100V line
+/- 3% within range
1 KHz
5V sine
3 seconds per channel
User preset from 1 min to 48 hrs
User preset at each channel
Normal, Fault, Buzzer, Auto run
2 x 16 characters w back light
Continuous buzzer with Off option
3A
24V DC for individual channel
482 x 44 x 180 mm
2.3 kg
Fault alert with LED indicators and switchable buzzer
Detection test interval setting from 1 min to 48 hours
Short burst test signal, minimizing interruption to PA operation
User setting for detection sensitivity for open, short and leakage
Aux 24V DC output for volume controller overriding during testing mode
Rear View:
multiply LS4600
as required
ZONE
SELECTOR
LS4600
SPEAKER
100V
10
3
4
3
2
1
PATCH
PANEL
VOL CTRL
5
6
7
SPEAKER ZONE SELECT
5
6
8
9
1
2
UP
DOWN
M ENU
4
5
6
11
12
1
2
3
4
5
6
ALL
CALL
a m pe r e s
QP2000
POWER AMPLIFIER
VR7000
4
SPEAKER
PATCH PANEL
SPEAKER VOLUME
2
1
OFF
3
4
5
3
I
O
OVERRIDE
OVERRIDE
1
5 0 0 W 1 0 0 V L IN E P O W E R A M P LIFIE R
POW ER
2
E/M
OVERRIDE
VR 7000
2
ZS 5121
Q P 2 5 00
SPEAKER VOLUME
1
OFF
3
4
5
OVERRIDE
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.9 kg
24V emergency
override signal
37
AM4120
Amplifier Monitor Panel
Introduction
AM4120 shall be used to monitor amplifier outputs of 70 / 100V line at the rack which
is equipped with level meter, amplifier output LED and speaker for audio monitoring. It
can also be used as a tool to calibrate sound output level of each amplifier from the
rack.
Rear View:
amperes
Features
12 inputs for 70 / 100V line amplifier outputs
Dual mode monitoring with continuous signal indicator
Audio monitoring with volume control
Operating voltage
Power consumption
Amplifier inputs
Monitoring mode
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 2.8 kg
Dimensions (WxHxD)
Weight
50 mW
12 : 70 / 100V line
Audio : 1W speaker with 5 presets
Visual : segment LED level meter
LED for all channels
482 x 44 x 180 mm
2.1 kg
AS4000 | Amplifier Surveillance Module
AS4000 is used to monitor the status of 70 / 100V line power amplifiers which do not
have built in detection module. Every amplifier shall employ one AS4000 and the dry
contact output from the unit shall then be connected to Amperes AX700. Repeating
this link shall then form an automatic amplifier fault changeover / surveillance
system.
Features
Interval Pilot Tone injection ; reduces strain to amplifiers
Works independently with or without availability of audio signal
Low distortion to original audio signal
Status monitoring via LED ; Pilot Tone and amplifier fault
Compatible with most 70 / 100V line amplifiers in the market
38
Operating voltage
Power consumption
Input impedance
Output impedance
Max audio input
Max audio output
Transmit interval
Detection delay
Recovery time
Frequency response
Detection output
Dimensions (WxHxD)
Weight
200 mW nominal
10 K balanced
600 Ohm balanced
0.75V
1.2V
10 seconds
20 seconds
30 seconds
20 - 20 KHz
NO and NC dry contact
120 x 96 x 28 mm
330 gms
ZS5062 / ZS5122
Selector & Data Decoder
amperes
ZS5062 | 6 Ch Speaker Zone Selector
ZS5122 | 12 Ch Speaker Zone Selector
RS485
Fail Safe
Remote Monitor
Features
Introduction
Available in 6 and 12 zones ; expandable to 192 zones
These next generation of zone selectors are introduced to meet the new demands
for a fail safe equipment. They are available in 6 and 12 zones and expandable to
larger configurations.
Fail safe zone trigger during power or unit failure
Remote zone triggering via analogue and RS485 data
ZS5602 / 5122 may look and function similarly with other zone selectors but they
have several distinctive features for safety, operation and monitoring. All zone
contacts shall automatically closed during power failure or damage to the unit, which
is vital to continuous emergency broadcast. RS485 communication port is available
for remote triggering or monitoring via PMX software.
Zone monitoring via PMX II software
Local paging overriding bypassing BGM
Flexible amplifier to zone configuration
ZS5062
ZS5122
Weight
2
4
8
ON
AMP 6
ZON6
100V
100V
100V
100V
100V
100V
100V
100V
COM
ZON5
COM
AMP 5
COM
ZON4
COM
AMP 4
COM
ZON3
COM
AMP 3
COM
ZON2
COM
AMP 2
COM
ZON1
COM
AMP 1
COM
REMOTE SELECT
ZONE 1 TO 6
1-Z1
2-Z2
3-Z3
4-Z4
5-Z5
6-Z6
7-24V
8-COM
100V
UNIT ADD
1
100V
RELAY RELAY Z RS485
TRIG CONT PR A B
100V
-
100V
+
COM
ZONE SELECTOR
ZS 5062
AMPLIFIER INPUTS - ZONE OUTPUTS FOR ZONE 1 TO 6
AMPERES ELECTRONICS
AMPERES ELECTRONICS
2
4
ON
8
100V
100V
100V
100V
100V
100V
100V
Packing information
Carton
:
Weight
:
:
Qty
:
COM
ZON12
COM
AMP12
COM
ZON11
COM
AMP11
COM
ZON10
COM
AMP10
COM
ZON9
COM
100V
AMP 9
100V
100V
ZON8
COM
100V
100V
AMP 8
100V
100V
ZON7
COM
100V
AMP 7
COM
100V
100V
REMOTE SELECT
ZONE 7 TO 12
1-Z7
2-Z8
3-Z9
4-Z10
5-Z11
6-Z12
7-24V
8-COM
100V
ZON6
COM
AMP 6
100V
ZON5
100V
AMP 5
COM
ZON4
COM
AMP 4
COM
ZON3
COM
AMP 3
COM
ZON2
COM
AMP 2
COM
ZON1
COM
AMP 1
COM
REMOTE SELECT
ZONE 1 TO 6
1-Z1
2-Z2
3-Z3
4-Z4
5-Z5
6-Z6
7-24V
8-COM
100V
UNIT ADD
1
COM
RELAY RELAY Z RS485
TRIG CONT PR A B
COM
-
100V
+
100V
DC 24V
100V
Rear View ZS5122:
COM
ZS5122
24V DC via PS9400 adaptor
6.25W
3.29W
0.72W
0.96W
0.14A
0.26A
0.03A
0.04A
500W at 100V line
6
12
6
12
Front panel switch and remote
16
-ve triggered (common ground)
Individual zone switch, Priority
RS485 19.2 kbps baud rate
Individual, All Call
Local zone selection bypassed when remote
trigger is activated
482 x 44 x 180 mm
1.85 kg
2 kg
DC 24V
ZONE SELECTOR
ZS5062
ZS 5122
Operating voltage
Power consumption (idle)
Power consumption (All Call)
Current consumption (idle)
Current consumption (All Call)
Max load / channel
Number of zones
Amplifier inputs
Zone selection
Cascade limitation
Remote triggering
Indicators
Data communication
Switching mode
Rear View ZS5062:
560 (W) x 95 (H) x 295 (D) mm
ZS5602 : 2.5 kg
ZS5122 : 2.7 kg
1 unit / carton
39
ZS5601 / ZS5121
6 / 12 Ch. Speaker Zone Selector
Selectors & Data Decoder
amperes
6 Ch Speaker Zone Selector | ZS5601
12 Ch Speaker Zone Selector | ZS5121
Introduction
Features
ZS5601 and 5121 are trusted product for speaker zone selection which had been used
for more than a decade.
Available in 6 (ZS5601) and 12 zone (ZS5121) respectively with ALL CALL
They provide direct zone switching for single source PA setup via front panel switches or
through remote port connected to Amperes PM Series paging desk, or through Amperes
TD decoders when PD series of paging desks are used. Other made of paging consoles
are compatible with ZS provided they have negative triggering switching ports.
Remote zone triggering port via external paging microphone or console
A distinctive feature shall be the remote override function which bypasses local zone
selection whenever a paging mic connected to it is activated. The individual input and
output connections make it flexible for amp-zone configurations as well as for matrix
setup.
Expandable to more zones as required
Paging override by Amperes paging console with Priority override indicator
Emergency paging mic triggering port with dry contact for volume controller
overriding application
Flexible amplifier to zone configuration
ZS5601
ZS5121
DC 24V
+
RLY
TRIG
PLEASE OBSERVE LINE POLARITY WHEN CONNECTING CABLES
AMP.6
REM. PAGING MIC
E/M TRIG
REL.CONT
DC24V
ZONE 1
ZONE 6
SPEAKERS
AMP.1
AMP
INPUTS
TYPICAL CONFIGURATION
DO NOT OVERLOAD ZONE
MAX LOAD/ZONE : 400W
CONNECT REMOTE / RELAY
PORT ONLY IF APPLICABLE
AMP.IN LOOPING ALLOWED
REMOTE
SELECT
ZON6
COM
COM
AMP 6
100V
COM
ZON5
COM
COM
AMP 5
100V
COM
ZON4
100V
AMP 4
100V
COM
COM
ZON3
100V
AMP 3
100V
COM
ZON2
COM
AMP 2
100V
100V
ZON1
100V
AMP 1
COM
1-Z 1
2-Z 2
3-Z 3
4-Z 4
5-Z 5
6-Z 6
7 --V E
8 -+ V E
COM
P IN
P IN
P IN
P IN
P IN
P IN
P IN
P IN
100V
REMOTE SELECT
100V
RLY RLY ZS
TRIG CON PR
100V
DC 24V
+
ZONE OUTPUTS
Rear View:
AMPERES ELECTRONICS
RLY ZS
CON PR
P IN 1 -Z 1
P IN 2 -Z 2
P IN 3 -Z 3
P IN 4 -Z 4
P IN 5 -Z 5
P IN 6 -Z 6
P IN 7 -AC
P IN 8 -PR
P IN 1 -Z 7
P IN 2 -Z 8
P IN 3 -Z 9
P IN 4 -Z 10
P IN 5 -Z 11
P IN 6 -Z 12
P IN 7 -AC
P IN 8 -GND
24V DC REG.
POWER
TEST
AM 6000
S IR E N A C T IV A T E
POW ER
FIR E
POWER
PA 2480
PROTECT
amperes
CLIP
SIGNAL -10 dB
SIGNAL -40 dB
DC 24V
+
RLY
RLY ZS
TRIG CON PR
P IN 1 -Z 1
P IN 2 -Z 2
P IN 3 -Z 3
P IN 4 -Z 4
P IN 5 -Z 5
P IN 6 -Z 6
P IN 7 -AC
P IN 8 -PR
P IN 1 -Z 7
P IN 2 -Z 8
P IN 3 -Z 9
P IN 4 -Z 10
P IN 5 -Z 11
P IN 6 -Z 12
P IN 7 -AC
P IN 8 -GND
M IC
a mp e r e s
for E/M override
Dry contact for link to other
application / EM overriding
TO SPEAKERS (VARIOUS ZONES)
N+3 Multicore Cable
N= No of Zones
remote zone trigger
AMPERES PM1060 / 1120 REMOTE
PAGING MICROPHONES
(OR OTHER BRANDS WITH NEGATIVE TRIGGER)
40
560 (W) x 95 (H) x 295 (D) mm
ZS5601 : 2.3 kg
ZS5121 : 2.8 kg
1 unit / carton
POWER AMPLIFIERS
(70/100V)
E/M PANEL TRIGGER
OR OTHER
TRIGGERING
METHOD
Packing information
Carton
:
Weight
:
:
Qty
:
ZS5601
OR
ZS5121
Operating voltage
Power consumption
Max load / channel
Number of zones
Amplifier inputs
Zone selection
Cascade limitation
Remote triggering
Indicators
Switching mode
Weight
ZS5601
ZS5121
24V DC adaptor
3.5W, 0.14A w All Call 6.8W, 0.28A w All Call
500W at 100V line
6
12
6
12
Front panel switch and remote
Unlimited
-ve triggered (common ground)
Individual zone switch, Priority
Individual, All Call
Local zone selection bypassed when remote
trigger is activated
482 x 44 x 180 mm
1.7 kg
2.1 kg
ZS5602 / SS6401
amperes
ZS5602
Introduction
Features
ZS5602 shall be suitable for uninterrupted paging setup, ie. when an announcement
to a zone is made, other areas with BGM shall not be interrupted.
Available in 6 zones for BGM and 6 for Paging with ALL CALL
This shall require two sets of amplifiers connected to the ZS5602, thus the system
shall consist of two sources, one being BGM and the other as Paging.
Remote zone triggering port via external paging mic
Similarly to ZS5601 / 5121, paging zone can be remotely triggered and each zone
shall have separate amp input - zone output terminals, thus making it flexible for
amp-zone configuration.
Aux DC output for selected paging zone
Rear View ZS5602:
PLEASE OBSERVE POLARITY WHEN CABLING
ZON6
COM
AMP6
COM
ZON5
COM
COM
AMP5
100V
COM
ZON4
100V
COM
AMP4
100V
COM
ZON3
100V
COM
AMP 3
100V
COM
ZON2
100V
AMP 2
100V
BGM AMPLIFIER INPUTS - NORMAL BGM OUTPUTS
COM
ZON1
100V
AMP 1
COM
6
100V
24 V
4 5
COM
3
100V
2
100V
ZONE DC OUTPUTS
1
100V
COM
COM
COM
ZON6
100V
COM
( OR 3 WIRE SYSTEM PRIORITY ZONE OUTPUTS )
AMP 6
100V
COM
ZON5
100V
COM
AMP 5
100V
COM
ZON4
100V
AMP 4
100V
COM
ZON3
100V
COM
AMP 3
COM
ZON2
100V
COM
PAGING AMPLIFIER INPUTS - ZONE OUTPUTS
100V
COM
AMP 2
100V
ZON1
100V
100V
AMP 1
Expandable or link multiple units to form more zones
Emergency paging mic triggering port with dry contact for volume controller
overriding application
Suitable for 3 or 4 wire system
( 3 WIRE SYSTEM ONLY )
REMOTE PAGING
MICROPHONE
BGM SOURCES
MIXER MX2222
OFF
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
Operating voltage
Power consumption
Insertion loss
Max load / channel
Number of zones
Amplifier inputs
Zone selection - BGM
Zone selection - Paging
Indicators
Aux output voltage
Dimensions (WxHxD)
Weight
24V DC ; 0.5A
10W ; 0.42A at ALL CALL
0.5 dB max
500W at 100V line
6
6 BGM ; 6 Paging
Front panel switch
Front panel switch, remote
Zone LED
24V DC ; 3A max / zone
482 x 44 x 180 mm
2.2 kg
SELECT
TONE CTRL
TUNER
OFF
MIN
MAX
CHIME
MIN
MAX
SIG IN
MIN
SIG IN
MAX
MIN
MAX
SIG IN
MIN
SIG IN
MAX
MIN
MAX
SIG IN
MIN
SIG IN
MAX
MIN
POWER
MASTER
EXT INPUT
MX 2122
MIN
TREBLE
I
CASS
CD
MAX
MIXER
MAX
SIG IN
AUX
O
BASS
MIN
MAX
SIG IN
MUSIC SOURCE
BGM
Paging
PAGING AMPLIFIERS
BGM AMPLIFIERS
PA 2060
PA 2060
60 Watts
60 Watts
POWER
POWER
POWER
AM 6000
I
PROTECT
O
SIGNAL -10 dB
POWER
AM 6000
CLIP
SIGNAL -40 dB
I
PROTECT
O
SIGNAL -10 dB
CLIP
SIGNAL -40 dB
BGM output
Paging output
zone control
24V DC
ZS5602
multiply ZS5602 for
more zones
Z1
24V DC override
100V
SPEAKERS
VOL CTRL
Z6
SS6401 | 4 Input BGM Source Selector
SS6401 has 4 BGM source input via RCA jack with mono output suitable for PA
system. Its has line balancing circuitry which provide equal output level no matter
which input is selected, as different BGM source has different output level. This
avoids the trouble to adjust mixer volume whenever a different source is changed.
Input connection
Output
Gain (max)
Selection
Dimensions (WxHxD)
Weight
4 input sources ; Cassette, CD, Tuner and Aux
Input level balancing circuit for constant output level for different type of BGM source
Rear View SS6401:
SS 6401
24V DC ; 0.3A
0.15A
: 2V / 47 K Ohm
CD
: 600 mV / 10 K Ohm
Tuner
Cassette : 500 mV / 10 K Ohm
: 1.25V / 20 K Ohm
Aux
RCA mono
RCA mono, 1V 600 Ohm
CD : -6 dB / Tuner : 4 dB
Cassette : 6 dB / Aux : -2 dB
Daisy chain
482 x 44 x 180 mm
1.8 kg
MUSIC SOURCE SELECTOR
Input voltage
Consumption
Input level / Imp
(max input)
Features
CASS
DC 24V
DC SUPPLY RATING :
24V DC, 150 mA
OUTPUT
( UNBALANCE )
1 V MAX
AUX
TUNER
CD
INPUT SENSITIVITY / IMPEDANCE
TUNER
CD
CASS
AUX
: 200mV / 47K
: 500mV / 47K
: 200mV / 47K
: 200mV / 47K
+ -
Packing information
Carton
:
Weight
:
:
Qty
:
560 (W) x 95 (H) x 295 (D) mm
ZS5602 : 2.5 kg
SS6401 : 2.9 kg
1 unit / carton
41
TD6080
Selectors & Data Decoder
8 Ch Decoder / Zone Selector
amperes
Introduction
Features
Integrated paging mic zone decoder and zone selector for simplified system
interconnections
Multipoint paging input from PD series of paging mics
8 input / 8 output configurable amp – speaker line connections
TD6080 is engineered for convenience, combining data decoder and zone selector in a
box, which is translated into fewer component counts and cabling cost. It is also suitable
for decentralised installations of multiple locations, which can communicate with central
paging system through RS485 or LAN.
Cascade feature for larger number of zones
Configurable as group BGM / Paging for matrix setup
Operating voltage
Consumption
Max load / channels
Cascade Quantity
Input circuits
Number of zones
Amplifier inputs
Zone selection
Indicators
Switch mode
Rear View:
TIME OUT 5 MIN
LINE / MIC OUTPUT
MASTER / SLAVE
0
DC 24V
L
S
5 M M
+
Packing information
Carton
: 560 (W) x 95 (H) x 295 (D) mm
Weight
: 2.5 kg
Qty
: 1 unit / carton
PD2400 / 2800
PAGING MIC 2
PD2400 / 2800
PAGING MIC 1
PD2400 / 2800
PAGING MIC 3
Cat 5e
EX1103A
audio & data
2pr screen
TD6080
DECODER
Zone Output
MX2222
PREAMPLIFIER
MIXER
audio output
(mic / line level)
OFF
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
SELECT
TUNER
MAX
CHIME
MAX
MIN
SIG IN
MAX
MIN
MAX
SIG IN
MIN
MAX
MIN
SIG IN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
Amp (100V Line) - - - - - - - - - - - - - O/P
TONE CTRL
OFF
MIN
MIN
SIG IN
POWER
MASTER
EXT INPUT
MX 2122
I
CASS
CD
a m pe re s
O
AUX
MAX
MIXER
TREBLE
BASS
MIN
MAX
SIG IN
MUSIC SOURCE
audio
output
POWER
MENU
QP2500
I
a m pe re s
O
UP
DOWN
QP2000s
POWER AMPLIFIER
Zone 1
SPEAKERS
Zone 8
The illustration shows a setup using multiple paging mic with TD6080 as zone decoder and zone selector
42
24V DC
6W (250 mA)
500W at 100V line
31 Unit (248 zone)
2
8
8
Front panel switch & remote
Individual zone switch
Individual, All Call Local
zone selection bypassed when remote
trigger is actived
AUDIO
Input impedance (Ohm)
Output impedance
Freq response
Audio input
Max audio output
Line : 10 K
600 Ohm balanced
70 ~ 15 KHz
Line
Line 1.2V
DATA
Data protocol
Baud rate
Dimension (WxHx D)
Weight
RS485
19.2 K bps
482 x 44 x 180 mm
2 kg
24 Ch Data Decoder
amperes
TD6240
Introduction
TD6240 is an intermediary equipment between PD series of paging microphone and
zone selectors. It accepts up to 3 mic input circuits ; enabling multipoint paging setup
and has 24 analogue switching circuits to be connected to ZS series of zone selectors.
More than one TD6240 can be stacked to achieve expanded zone quantity.
Features
Expandable and addressable to cater for more than 24 zones
Priority setting for multi point paging setup
Selectable balanced audio output level (mic or line)
Compatible with most zone selectors with remote triggering port
Connects directly to ZS5601 / 5121 via remote triggering port using RJ45 connector
Rear View:
Operating voltage
Consumption
Switching channels
Cascade / max zones
24V DC
2.4W (100 mA)
24
8 (max 192 zones)
Input circuit
Output connection
(Triggering)
3
RJ45 to ZS zone selector
AUDIO
Input impedance (Ohm)
Output impedance
Freq response
Audio input
Max audio output
Line : 10 K
600 Ohm balanced
70 ~ 15 KHz
Line
Line 1.2V
DATA
Data protocol
Baud rate
Dimension (WxHx D)
Weight
RS485
19.2 K bps
482 x 44 x 180 mm
2.5 kg
PD2400 / 2800
Paging Mic 2
PD2400 / 2800
Paging Mic 1
PD2400 / 2800
Paging Mic 3
Cat 5e
EX2800
EX2800
EX2800
Note :
Priority level not important when
connect to the Mic Connection
Port of T6240
2pr screen
TD6240
DECODER
Cat5/ multicore
cable for zone triggering
audio output
(mic / line level)
MX2222
PREAMPLIFIER MIXER
OFF
CH1
CH2
CH3
CH4
CH5
CH6
SOURCE
SELECT
TONE CTRL
TUNER
OFF
MIN
MAX
CHIME
MIN
MAX
MIN
SIG IN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
SIG IN
MAX
MIN
POWER
MASTER
EXT INPUT
MX 2122
MIN
I
CASS
CD
MAX
MIXER
a m pe re s
AUX
ZS 5121
a m pe re s
O
OVERRIDE
TREBLE
BASS
MAX
MIN
SIG IN
SIG IN
MAX
1
2
3
4
5
6
7
SPEAKER ZONE SELECT
8
9
10
11
12
ALL
CALL
MUSIC SOURCE
ZS5121 ZONE SELECTOR
POWER
MENU
QP2500
I
a m pe re s
O
UP
DOWN
POWER AMPLIFIER
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 3.2 kg
SPEAKERS
43
BC9740
24 DC Automatic Battery Charger
Power Distribution
amperes
Features
Constant DC voltage charging for 24V battery bank
4A initial charging current with reducing rate over charging time
RS485
Remote
Battery Protection
Built in surge protection and resetable fuse
Output short circuit protection
Introduction
Thermal protection against overheating
Meet the all new next generation of innovative Battery Charger, which has been
engineered to meet the requirement of installers and users alike. It is compact in 1 HU
height, built with the latest technology for efficient charging, controls and monitoring
purpose.
Auto low battery disconnection with LCD indication
Driven by powerful ARM processor, it works to protect against misconnections,
prolonging battery life with its battery monitoring feature and communicates to provide
human interaction. RS485 data port is available for external monitoring via PMX II
Software and can be readily linked up to LAN through iPX5500 Com Box.
Battery reversed polarity protection
Rear mains switch to avoid unnecessary switching off the unit
RS485 communication for remote monitoring via PMX II software
Rear View:
Input voltage
Charging voltage
Charging current
Idle power consumption
Protections
Indications
Displays
Communication
E/M back up Amp rating
Terminals
Dimensions (WxHxD)
Weight
230 / 240V ac
28.8V dc
4A; (max 5A)
1.3W
25A resettable fuse at battery back up output
Low battery auto disconnection, reverse polarity,
standby protection
AC mains, short circuit and low battery
Charging current
Charging voltage
Battery voltage
Output current
Battery reverse polarity
RS485 out; link to Amperes PMX II LAN via
iPX5500 comm. box for remote monitoring
25A max
( Use external contactor / relay if required )
Battery input , EM load
482 x 44 x 180 mm
2.62 kg
LOAD PROTECTION
-
+
BATTERY
INPUTS
REVERSED
POLARITY
WARNING
Amperes invites you to experience this innovative product which we had meticulously
developed for the convenience of the valued users.
-
+
RS485
+A -B
AMPERES ELECTRONICS
PRESS TO RESET
WARNING !
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
THIS UNIT MUST BE EARTHED
BATT IN
BACK UP
DC OUT
BC 9740
DC 30A
BC9740
PREV
ENTER
MENU
NEXT
POWER
BC 9740
amperes
CHARGING
FAULT
BATT IN
TERMINALS
Refer Note 1
BACK UP
DC OUT
+
+
-
24V DC BATT.
BANK
+
12V
-
BACK UP DC OUT
TERMINALS
Cable Type: Refer Note 2
+
12V
Amperes PS9400
24V power supply
I
PS 9400
amperes
O
bypass for
heavy load
OPTIONAL HIGH
AMP. RATING
CONTRACTOR
Refer Note 2
TO EQUIPMENTS
DC SUPPLY
CONTACTOR (24V DC COIL)
TO HEAVY LOAD
(POWER AMPS)
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 3.2 kg
44
SQ9715 / PS9400
Sequential Power Switcher
amperes
Power Distribution
SQ9715
Features
Introduction
7 channel with 6A per channel; total load of 15A with surge protection
Cascade 2 units to form 14 channel setup
ON / OFF sequential switching
Remote switching port via external noiseless contact
AC output via IEC connectors with channel isolation via DIP switch
Ch. 7 with delay Off option for 2 min ; suitable for video projector connection
SQ9715 is suitable for applications in PA, sound and AV system in which it manages
the powering sequence of every equipment in orderly manner. It works to provide a
some degree of protection to the lifespan of the equipment as random powering may
cause irreversible damage.
It has internal surge protection to kill harmful incoming power spikes. An important tool
that works to safely powering up your equipment with a touch of a button.
Rear View:
Lock mode to avoid incidental switching
Operating voltage
Power consumption
Output voltage
Max load / channel
Max total load
Output connection
Max cascade
Surge protection
Clamping voltage
Turn on sequence
Turn off sequence
Step timing
Delay off option
Delay off timer
Switch lock
Indicators
Dimensions (WxHxD)
Weight
230 / 240V ac
50 mW (without load)
230 / 240V ac
6A
15A
IEC female socket
2 uts : total 14 channels
L-N, L-E, N-E.
870V ac
Step 1 to 7 incremental
Step 7 to 1 decremental
2 seconds
Channel 7 via DIP switch
2 minutes
Via front switch
AC mains, Ch. on, Lock
482 x 44 x 180 mm
2.7 kg excl. accessories
ac output
CH.1 LOAD
:
:
:
:
ac
supply
CH.7 LOAD
ac
supply
SQ9715
MASTER
link cable
Units shown in cascade mode with 14
channels in total.
Ch 14 is last channel with delay option
Control only at Master unit
SQ9715
SLAVE
CH.8 LOAD
:
:
CH.14 LOAD
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 3.3 kg
Regulated 24V DC Power Supply | PS9400
IMPROVED
Input ac voltage
Output voltage
Rating
No load consumption
Efficiency
Indicators
Protections
Output DC protection
Terminals
Dimensions (WxHxD)
Weight
Packing information
WxHxD
: 560 x 95 x 295 mm
Weight
: 3.3 kg
220 ~ 240V ac
24V +/- 1%
4A nominal ; max 4.5A
50 mW
83%
AC mains, battery input, DC output
Built in surge protection
Short circuit
Overload (105% ~ 150%)
Over voltage (115% ~ 135%)
Manual reset circuit breaker
Batt input and load ; barrier connector
482 x 44 x 180 mm
2.6 kg
PS9400 is a rack mounted 24V DC regulated power pack designed uniquely for PA installations.
It comes with built in changeover relay which shall be connected to back up 24V DC to allow
continuous and uninterrupted supply to the whole installation whenever the mains failed.
Features
4V DC 4A output highly regulated switching power supply
Manual reset output circuit breaker protection
Built in surge and short circuit protection
Back up battery overriding relay
Rear View:
45
VR7600 & AV7200
amperes
Volume Controllers / Patch
Features
6 zones with 50 / 100 / 150W 100V line rating for each zone
Customised zone rating option available
VR7600 - Rack Mounted Zone Volume Controllers
VR series is available in three variants with 6 zones at each panel, to be mounted at rack
to enable volume of each zone to be controlled or set at the control room.
Suitable for 4 wire system : 2 for 100V audio & 2 for 24V DC overriding
Built in overriding relay for emergency volume bypass
VR should be installed before LS4600 to avoid false fault detection due to variation of impedance
whenever volume is adjusted.
POWER
AMPLIFIERS
PA 2120
120 Watts
POWER
POWER
PA 2120
VR7605 / VR7610 / VR7615
Power rating
50 / 100 / 150W 100V line / zone
Overriding voltage
24V DC
Overriding current
15 mA per channel
Attenuation
6 steps incl. OFF
Attenuation / step
6 dB / step
Attenuation method
Auto transformer
Size (W x H x D)
482 x 88 x 60 mm
Weight
2.1 / 3.1 / 3.2 kg
I
PROTECT
O
SIGNAL -10 dB
CLIP
SIGNAL -40 dB
ZONE SELECTOR
24V DC for
emergency
override
ZS 5121
OVERRIDE
1
2
3
4
5
6
7
SPEAKER ZONE SELECT
8
9
10
11
12
ALL
CALL
VR7000 SERIES
LINE SURV.
MENU
ENTER
PRE
NEXT
STATUS
CH1
CH2
CH3
CH4
CH5
CH6
BUZZER
AUTO
NORMAL
FAULT
24V
100V
100V
VOLUME
CONTROLS
SPEAKERS
AV7200 | 100W 100V Line Auto Volume Controller
AV7200 is used for controlling speaker volume automatically for a localised area by
adjusting the 100V line audio according to the ambient noise. As it varies the volume
at 100V instead of sending control signal to the system, it can be easily applied to the
existing systems without having to lay new cablings or installing new equipment.
Among suitable areas are shopping malls, stations, building lobbies, etc.
Features
Installation at localised area (at existing volume controller) without additional
cable re-run (easily retrofit to existing system)
100V speaker line control with 6 step attenuation
Adjustable noise sensing sensitivity
POWER AMPLIFIER
Built in overriding relay for emergency volume bypass
24V DC for
overriding
LS4600
(optional)
100V Line
24V O/Ride
A V 7 2 00
24V DC PSU
via adaptor
A U T O M A T IC V O L U M E C O N T R O LL E R
HI
M IC
LO
HI
LO
S E N S IT IV IT Y
1
2
3
4
5
O U T P U T LE V E L
S E N S IT IV IT Y
6
1
O V E R R ID E
AV7200
ZONE SPEAKERS
46
A V 7 2 00
A U T O M A T IC V O L U M E C O N T R O LL E R
M IC
2
3
4
5
O U T P U T LE V E L
6
O V E R R ID E
AV7200
ZONE SPEAKERS
Power rating
Operating voltage
Attenuation
Emergency overriding
Sensitivity adjustment
Weight (excl. enclosure)
100W 100V line
24V DC : 40 mA
6 steps ; -6 dB per step
24V DC ; 0.15A
2 level
247 x 87 x 50 mm
1.1 kg
Speaker Volume Controllers
amperes
VC7000 & VC8000
Volume Controller / Patch
From contemporary to classic design, Amperes offers choices for the installation
needs. The variants are in three different designs and available in various ratings,
ranging from 5 watts to 150 watts 100V line.
They are suitable for 4 wire system installation with built in emergency overriding
relay and overriding LED indicator.
Features
Suitable for 4 wire system : 2 for 100V line , 2 for 24V DC overriding signal
Built in overriding relay to allow emergency signal to bypass volume attenuation
Overriding LED indicator whenever EM paging is activated
5 preset attenuation with OFF
VC7000 - 5 - 150W 100V (86 x 86 mm)
Large cable terminal block for ease of termination
Power rating
Overriding voltage
Overriding current
Attenuation
Attenuation / step
Attenuation method
Refer to variants
24V DC
15 mA per channel
6 steps incl. OFF
6 dB / step
VC7005 / 7010 / 8010 - Resistive
Others - Auto transformer
White
VC7000 / 8000 - 86 x 86 x 40 mm
VC7000A - 70 x 120 x 40 mm
VC7805 / 7005 / 7010 - 100 gms
VC7030 / 7050 - 248 gms
VC7100 / 7150 - 382 gms
Colour
Size (W x H x D)
Weight
VC8010
VC8030
VC8050
VC8100
Optional item :
Conceal enclosure
Surface enclosure
77 x 77 x 60 mm
85 x 85 x 60 mm
VC8000 - 5 - 100W 100V (86 x 86 mm)
Variants :
VP7000 (OPTIONAL)
24V O/R
From
amplifier
localised area
100V
VC8000
100V
For 70 x 120 faceplate series:
Vertical and Horizontal version available
- 250 gms
- 254 gms
- 264 gms
- 269 gms
24V DC
Override
VC7000A - 5 - 100W 100V (70 x 120 mm)
VC8000
SPEAKERS
loop to next speaker
100V
SPEAKERS
loop to next speaker
4 wire system installation
NOTE :
Wall concealed installation shall require back enclosure with depth of min 50 mm from finishing surface
for models with auto transformer. Normal electrical back enclosure shall suffice for installation using
resistive volume controllers. ie. VC7005 / 7010 / 8010
VC8000 SERIES (86 X 86 mm)
10W 100V Line Resistive
VC8010 :
30W 100V Line Auto Trans
VC8030 :
VC8050 :
VC8100 :
VC7000 SERIES (86 x 86 mm)
10W 8 OHM Resistive
VC7810 :
VC7005 :
VC7010 :
VC7030 :
VC7050 :
VC7100 :
VC7150 :
VC7000A SERIES (70 X 120 mm)
VC7010A :
VC7030A :
VC7050A :
VC7100A :
47
Speaker Patchs
Volume Controllers / Patch
amperes
Introduction
VP7501 is used to isolate a group of speakers (meeting room, etc) from central PA
system to allow a separate PA amplifier to utilise those local speakers, but can be
overrided by main system when a 24V overriding signal is present.
VP7810 works similarly but the local speaker is 8 Ohm, ie. setup in hotel room with
speaker connected to TV audio output via a mini amplifier. In the event of
emergency, it shall allow the incoming 100V line to take over and to match the
speaker’s impedance.
Features
VP7501 - Local Speaker Patch Panel
Suitable for 4 wire system : 2 x audio, 2 x 24V DC overriding
Built in overriding relay for emergency bypass with LED indicator
Also available with 70 x 120 mm front panel
24V DC
Override
from main
PA system
VOL.CONTROL
patch using
1/4" mono
jack
LOCAL SPEAKER PATCH IN
100V
SPEAKER VOLUME
2
1
OFF
3
4
100V
5
OVERRIDE
VP7810 - 8 Ohm Speaker Patch
OVERRIDE
VP7501
SPEAKER
C/W
TRANS
100V
Power rating
Overriding voltage
Patch connection
Cablings
Size (front panel)
Weight (excl. enclosure)
Concealed (W x H x D)
Surface (W x H x D)
VP7501
VP7810
50W 100V line
10W 8 Ohm
24V DC : 15 mA
1/4”phone jack-front patch
Hardwired
4 wire system (2 audio ; 2 overriding)
86 x 86 mm
70 x 120 mm face plate available upon request
69 / 215 gms
77 x 77 x 60 mm
85 x 85 x 60 mm
audio inputs
MIXER AMP (LOCALISED)
VP7501 application schematic
audio in
from TV
etc
8 OHM OUT
MINI AMP
VC7805
VP7810
PA - TV BGM
EM OVERRIDE MODULE
SPEAKER VOLUME
2
1
OFF
3
4
5
OVERRIDE
OVERRIDE
100V output from
central PA system
24V DC Override
VP7810 application schematic
Packing information
Carton (W x H x D) : VP7501 / VP7810 : 580 x 510 x 310 mm
Weight
: VP7501 : 200 g
: VP7810 : 300 g
Qty
: VP7501 / VP7810 : 112 uts per carton
48
4 / 8 OHM
SPEAKER
Dual Cone
Ceiling Speaker
Speakers
Speaker Volume Controllers
amperes
CS510 / CS610 : DUAL CONE CEILING SPEAKER W ABS ENCLOSURE
Available in 5” and 6” of driver size complete with matching transformer of three tappings ;
1, 3 or 6W. Back enclosure are supplied as integral part of the speakers made from quality
ABS plastic. Installation is made easy with its screw mounting mechanism.
Packing information
CS510A
: 850 (W) x 385 (H) x 240 (D) mm
: 15 kg
: 20 uts per carton
CS610A
: 685 (W) x 475 (H) x 340 (D) mm
: 19.6 kg
: 18 uts per carton
CS515 : DUAL CONE CEILING SPEAKER W ABS ENCLOSURE
CS510A - 5” 6W 100V Line
CS610A - 6” 6W 100V Line
CS515 is a general purpose 5" 6W 100V line ceiling speakers which comes complete with
ABS honeycome grille and back enclosure. It is suitable for BGM and Paging application
and suitable for rust prove enviroment.
CS606 - 6” 6W 100V Line
Packing information
CS515
: 850 (W) x 385 (H) x 240 (D) mm
: 15 kg
: 20 uts per carton
CS606 : DUAL CONE CEILING SPEAKER W METAL ENCLOSURE
Available in 6” dual cone speaker with back metal enclosure, grill and baffle and multi tap
matching transformer of 1.5, 3 and 6W 100V line. This model shall be suitable for
installations that demand fire resistant version of dome.
CS515 - 5” 6W 100V Line
Packing information
CS606
: 420 (W) x 220 (H) x 345 (D) mm
: 6.5 kg
: 6 uts per carton
CS343 : WEATHERPROOF CEILING SPEAKER
CS343 is driven by a 4” dual cone speaker with built in matching transformer of dual taps
of 3 and 6W 100V line.
Made of quality ABS enclosure and aluminum grille, it is suitable for high humidity areas,
such as bathrooms and salty environment. Though compact in size, it delivers satisfactory
sound reproduction with high SPL level, good for listening pleasure as well as paging
clarity.
Packing information
CS343
: 550 (W) x 180 (H) x 465 (D) mm
: 9.5 kg
: 9 uts per carton
CS343 - 4” 6W 100V Line
CS510
SPEAKER
Power rating
Diameter
Cone type
Impedance (Ohm)
Freq response (+/- 5dB)
SPL @ 1W / m (+/- 3dB) 1 KHz
Magnet weight
TRANSFORMER
Tapping (100V line)
Primary impedance (Ohm)
Secondary impedance (Ohm)
PHYSICAL
Grille / enclosure
Cutting hole dim
Overall size (dia x height)
Weight
Colour
CS610
6W 100V line nominal (max 10W)
5” (125 mm)
150 ~ 19 KHz
93 dB
3 oz
CS606
6” (150 mm)
120 ~ 19 KHz
92 dB
5.3 oz
Dual cone
8
150 ~ 16 KHz
91 dB
2 oz
CS515
CS343
5” (125 mm)
4” (100 mm)
150 ~ 17 KHz
92 dB
3 oz
150 - 18 KHz
90 dB
1 / 3 / 6W
10 K / 3.3 K / 1.6 K
1.5 / 3 / 6W
6.7 K / 3.3 K / 1.6 K
8
1.3 / 6W
10 K / 3.67 K / 1.7 K
3 / 6W
3.3K / 1.67 K
White metal / ABS white
175 mm
140 mm
230 x 102 mm
177 x 130 mm
785 g
715 g
White metal
165 mm
200 x 100 mm
950 g
White
ABS Plastic
145 mm
175 x 95 mm
600 g
Aluminum / ABS
120 mm
140 x 130 mm
900 g
49
Co-axial
Ceiling Speaker
Speakers
amperes
CS620 / 840 CO-AXIAL CEILING SPEAKER
CS620 and 840 meets the requirement of hi fidelity of sound reproduction in areas
such as function halls, restaurants and also for sound reinforcement at banquet
halls. They are available in 6” and 8” version of speaker driver with tweeter and
100V line matching transformer.
Packing information
CS620
: 580 (W) x 510 (H) x 310 (D) mm
: 20 kg
: 7 uts per carton
CS840
CS620 / CS840
: 580 (W) x 510 (H) x 310 (D) mm
: 13.6 kg
: 4 uts per carton
CS518 SQUARE CO-AXIAL CEILING SPEAKER
CS518 matches other fittings at ceiling where most of them are in square or
rectangular shapes. It’s size is almost similar to square shape light fittings and is
loaded with co-axial 5” driver, delivering clear and crispy sound. It is suitable for
boutiques, residence, offices as well as lobbies.
Packing information
CS518
: 580(W) x 510 (H) x 310 (D) mm
: 17.8 kg
: 7 uts per carton
CS518
SPEAKER
Power rating
Diameter
Cone type
Impedance
SPL @ 1W / m (+/- 3dB) 1 KHz
Magnet weight
TRANSFORMER
Tapping (100V line)
PHYSICAL
Grille / enclosure
Cutting hole dim
Weight
Colour
50
CS620
CS840
CS518
20W 100V
6.5” (165 mm)
40W 100V
8” (200 mm)
Co-axial
8 Ohm
90 ~ 19 KHz
90 dB
15 oz
20W 100V
5” (125 mm)
80 ~ 18 KHz
88 dB
10 oz
20W
500
205 mm
240 x 145 mm
2.4 kg
40W
250
8
White metal / ABS white
240 mm
280 x 145 mm
2.9 kg
white
100 ~ 18 KHZ
85 dB
10 oz
2.5 / 5 / 10 / 20W
4K / 2K / 1K / 500
150 x 150 mm
180 x 180 x 135 mm
1.8 kg
Surface Mount Speaker
amperes
Speakers
SURFACE MOUNT SPEAKER
It is constructed with high quality ABS plastic with 4” dual cone speaker driver and
multi tapping matching transformer of 1 / 3 / 6 and 10W 100 V line. Suitable for wall
and ceiling installation with optional tilt mounting bracket. Available in white colour.
BS410 - 4” 10W 100V
Packing information
BS410
: 550 (W) x 220 (H) x 430 (D) mm
: 12 kg
: 12 uts per carton
DV410 - 4” 6W 100V
A classic yet favourite model which is suitable for installations in small enclosed
areas such as staircase, office, etc. Available in white colour with multi tap matching
transformer of 1 / 3 / and 6W 100V line, fit for vertical or horizontal installations.
Packing information
DV410
: 590 (W) x 400 (H) x 305 (D) mm
: 15.4 kg
: 18 uts per carton
BS506 - 5” 6W 100V
Wall mount speaker are suitable for any type of sound reproduction, for both paging
and background music. Available in white colour with high effeciency driver and line
transformers.
Packing information
BS410
: 550 (W) x 220 (H) x 430 (D) mm
: 12 kg
: 12 uts per carton
BS410
DV410
BS506
6W 100V
6W 100V
5”
SPEAKER
Power rating
Diameter
Cone type
Impedance (Ohm)
SPL @ 1W / m (+/- 3dB) 1 KHz
Magnet weight
4
100 ~ 16 KHz
92 dB
7.5 oz
Dual Cone
8
100 ~ 18 KHz
90 dB
3.0 oz
8
100 ~ 15 KHz
93 dB
3 oz
TRANSFORMER
Tapping (100V line)
1 / 3 / 6 / 10W
10 K / 3.3 K / 1.6 K /1K
4
1 / 3 / 6W
10 K / 3.3 K / 1.6 K
8
1 / 3 / 6W
10 K / 3.3 K / 1.6 K
8
PHYSICAL
Grille / enclosure
Overall size (WxHxD)
Weight
Colour
10W 100V
4”
ABS
ABS with metal grille
172 x 195 x 105 mm
185 x 205 x 90 mm
195 x 215 105 mm
1.1 kg
0.75 kg
White
51
Full Range Speaker
amperes
Speakers
FS420 & FS640 : FOREGROUND MUSIC SPEAKER
Available in 4” and 6” of driver size complete with matching transformer, selectable
power switch and mounting bracket. They are suitable for foreground soft music
such as restaurants, shops and general sound reinforcement in meeting room,
corridors, etc.
Packing information
FS420
: 440 (W) x 370 (H) x 250 (D) mm
: 9.65 kg
: 4 uts per carton
FS640
: 420 (W) x 345 (H) x 220 (D) mm
: 7.30 kg
: 2 uts per carton
FS338 : FOREGROUND MUSIC SPEAKER
FS420
( Black / White )
FS640
( Black / White )
4” 20W 100V
6” 40W 100V
FS338 is built as multi purpose speaker, optimising the features of smooth and
pleasant outlooks while maintaining the audio performance. Thus by its appearance
and sound quality, it can be employed in most indoor venues.
It is driven by 2 x 4” PP speakers and a 1” tweeter with 40W 100V line power. It can
also be driven directly from audio amplifier with 4 Ohm connections. Multiple power
tapping is available via the rotary switch from 5 to 40W 100V line.
Installation is rather flexible due to its dual angle mounting bracket. They can be
mounted in horizontal or vertical position. If wider coverage is required, then can be
installed in horizontal array format, with two, three or 360 degree format via the
optional mounting pole.
Packing information
FS338
: 560 (W) x 295 (H) x 165 (D) mm
: 7.6 kg
: 2 uts per carton
FS340 : FOREGROUND MUSIC SPEAKER
FS340 delivers smoothing sound with its 6” driver with tweeter. Available in 40W 100V
line with power selector for level adjustment to suit area of installation. It can be
installed vertically or horizontally, thanks to its flexible mounting bracket.
FS340
FS338
6” 40W 100V
4” 40W 100V
FS420
SPEAKER
Power rating
Diameter
Speaker type
Impedance
SPL @ 1W / m (+/- 3dB) 1 KHz
TRANSFORMER
Tapping (100V line)
PHYSICAL
Grille / enclosure
Overall size (WxHxD)
Weight
Colour
52
20W
4” (100 mm)
100 ~ 18 KHz
89 dB
1.25 / 2.5 / 5 / 10 / 20W / 8
4K / 2K / 1K / 500 / 8
Be it a restaurant, pub or cafe, meeting room or lobby, FS340 shall be the exact
candidate to choose from.
Packing information
FS340
: 455 (W) x 385 (H) x 240 (D) mm
: 7.8 kg
: 2 uts per carton
FS340
FS640
FS338
40W 100V
6” (150 mm)
4” x 2 (100 mm)
6” (150 mm)
2 way speaker with tweeter
8 Ohm
70 ~ 18 KHz
70 ~ 16 KHz
87 dB
88 dB
5 / 10 / 20 / 40W / 8
8
5 / 10 / 20 / 40W / 8
2K / 1K / 500 / 250 / 8
5 / 10 / 20 / 40W / 4
2K / 1K / 500 / 250 / 4
4
ABS enclosure with metal grille
170 x 215 x 150 mm
209 x 585 x 195 mm
137 x 385 x 262 mm
215 x 284 x 190 mm
2.2 kg
3.3 kg
3.4 kg
3.5 kg
White and Black
Black
Column Speaker
amperes
Speakers
CL900 | 20 - 60W 100V Line Column Speaker
Features
Slim design to match environment or hidden from view
CL912 - 60W 100V
Engineered for speech and BGM clarity
CL908 - 40W 100V
Power rating
Speaker components
Transformer tapping(100V)
Sensitivity (1m / 1w)
Frequency response
Dimension (mm)
Material
Weight with bracket (kg)
CL904
20W 100V
4 x 2”
10 / 20W
1k / 500
87 ± 3dB
350 x 79 x 89
1.4
CL908
40W 100V
8 x 2”
30 / 40W
330 / 250
88 ± 3dB
230 - 16 KHz
567 x 79 x 89
Aluminum
2.35
CL912
60W 100V
12 x 2”
50 / 60W
200 / 166
89 ± 3dB
CL904 - 20W 100V
782 x 79 x 89
3.2
Packing information
CL904
: 390(W) x 150(H) x 230(D) mm
: 3.60 kg
: 2 uts per carton
CL908
CL912
Built ruggedly with aluminum die extrusion housing and available in 3 power rating of
20 / 40 and 60W 100V line with dual power tapping.
: 608(W) x 168(H) x 235(D) mm
: 5.55 kg
: 2 uts per carton
Suitable for classrooms, hyper markets, mosques, ballroom, factories, passenger
terminals, exhibition areas etc.
: 828(W) x 168(H) x 235(D) mm
: 7.80 kg
: 2 uts per carton
20 - 40W 100V Line Column Speaker | CH700
CH700 SERIES COLUMN SPEAKER
CH740 -
Built ruggedly with aluminum die cast housing and available in 3 power rating of 20 / 30
and 40W 100V line with dual power tapping. Suitable for classrooms, hyper markets,
mosques, etc.
CH730 -
40W 100V
30W 100V
SPEAKER
Power rating
Diameter
Speaker type
Impedance
SPL @ 1W / m (+/- 3dB) 1 KHz
Magnet weight
TRANSFORMER
Tapping (100V line)
PHYSICAL
Grille / enclosure
Overall size (WxHxD) (mm)
Weight (kg)
Colour
CH720
CH730
CH740
20W 100V
2 x 4”
30W 100V
3 x 4”
Dual cone
8 Ohm
80 ~ 15 KHz
93 dB
7.5 oz
40W 100V
4 x 4”
85 ~ 15 KHz
91 dB
10 / 20W
1 K / 500
15 / 30W
660 / 330
8
CH720 -
20W 100V
75 ~ 15 KHz
95 dB
20 / 40W
500 / 230
Aluminum / metal grille
145 x 605 x 100
145 x 495 x 100
145 x 400 x 100
4.6
3.7
3.2
Dark grey / front black grille
Packing information
CH720
: 430 (W) x 310 (H) x 220 (D) mm
: 7.1 kg
: 2 uts per carton
CH730
: 520 (W) x 320(H) x 215 (D) mm
: 8.9 kg
: 2 uts per carton
CH740
: 620 (W) x 310 (H) x 220 (D) mm
: 10.5 kg
: 2 uts per carton
53
PS820 & SG390
Speakers
amperes
PS820 PENDANT BALL SPEAKER
Installations for high ceiling areas without columns, such as warehouses, hypermarkets
and large showrooms that require even sound distributions shall select PS820 pendant
ball speakers. It is built with 8” speaker of 20W 100V rating, delivering powerful and
evenly projected sound with 180° dispersion.
PS820
20W 100V Line
Packing information
PS820
: 310(W) x 310(H) x 300(D) mm
: 3 kg
: 1 unit per carton
SG390 OUTDOOR GARDEN SPEAKER
SG390 is the preferred choice for outdoor installations in parks, pool sides, etc, providing
excellent music for listening pleasure. With its green outlooks, it blends perfectly to the
shrubs, or hidden by leaves or grass. Thereby, its the right candidate to hide the sound
source unlike the bulky speakers suspended at poles which may affect the aesthetic
value of the environment.
Dual purpose
It is installed for paging purposes or to provide smooth music at outdoor installations.
360 dispersion
It provides an even dispersion of 360. An advantage over conventional speakers that may
require at least 3 units for such an angle of coverage. Thus reducing the speaker count.
SG390
Powerful sound
Available in 40W 100V line input, SG390 shall deliver the punch of sound, smoothness of
listening pleasure and clarity of voice announcement.
40W 100V Line
Built for all environment
High quality materials are used in the construction of the enclosure, which enable the unit
to withstand outdoor environment - rain or shine.
Packing information
SG390
: 345(W) x 390(H) x 345(D) mm
: 4.65 kg
: 1 unit per carton
PS820
Power rating
Power tapping (100V line)
Speaker diameter
Speaker type
Frequency response
SPL (1w/m @ 1 kHz)
Construction material
Colour
Dimensions
Weight
54
20W 100V line
5 / 10 / 20W
8” (200 mm)
2K / 1K / 500
80 - 18 KHz
91 dB
White
254 diameter (mm)
2.2 kg
SG390
Co-axial
ABS
40W 100V line
20 / 40W
5” (125 mm)
540 / 270
70Hz - 16 KHz
84 dB
Green
340 dia x 134 height (mm)
3.6kg
Horn & Projection
Speakers
amperes
SP219 : UNIDIRECTIONAL SOUND PROJECTOR
SP219 is used when a more directional sound projection is required for areas such
as at narrow corridors, tunnels, walkways, etc. It has aluminum body with metal
grille and available with standard power rating of 10W 100V line. Mounting position
can be either at wall or hanged from ceiling.
Packing information
SP219
: 550 (W) x 180 (H) x 465 (D) mm
: 9.6 kg
: 4 uts per carton
SP219 :
10W 100V LINE
SP319 : BIDIRECTIONAL SOUND PROJECTOR
It is suitable for narrow corridors, or walkways that requires sound reproduction in
two direction. Installing bi directional speakers may reduce the speaker counts and
thus lowering installation and cabling costs.
Packing information
SP319
: 550 (W) x 180 (H) x 465 (D) mm
: 12.8 kg
: 5 uts per carton
SP319 : 10W 100V LINE BIDIRECTIONAL
HS725 : WEATHERPROOF CLEAR HORN SPEAKER
HS725 meets the requirement of speakers with horn characteristics and yet delivers
sound with music clarity.
It is suitable for installations in almost any areas particularly outdoors, able to
withstand rain and shine.
Packing information
HS725
: 440 (W) x 250 (H) x 370 (D) mm
: 5.1 kg
: 1 unit per box
HS725 : 30W 100V LINE
HS725
SP319
SP219
Power rating
Power tapping (100V Line)
Speaker
Frequency response (+/-3 dB @ 1 KHz)
SPL (1W / m @ 1 KHz)
Grille / enclosure
Overall size
Weight
Colour
5”
2.9 kg
10W 100V
Fixed at 10W
1K
8
130 ~ 15 KHz
91 dB
Mild Steel / Aluminum
138 (Dia) x 205 (H) mm
White
2 x 5”
3.5 kg
HS725
30W 100V line
30 / 15 / 7.5 / 3.8W
5” (125mm)
333 / 667 / 1.3 K / 2.6 K
8
100 ~ 10 KHz
90 dB
Aluminum / ABS
366 (W) x 172 (H) x 272 (D) mm
3 kg
Light grey
55
Horn Speaker
Speakers
amperes
HS815 8” 15W 100V LINE
HS830 12” 30W 100V LINE
HS815 & HS830 : HORN SPEAKER WITH ROUND FLARE
Both models are constructed using rounded aluminum flare of 8” (HS815) and 12”
(HS830) with multiple power selection via rotary switch. Suitable for schools,
mosques, car parks, factories at indoor or under shade installations and that
requires omni direction sound broadcast.
Packing information
HS815
: 695 (W) x 480 (H) x 520 (D) mm
: 23 kg
: 12 uts per carton
HS830
: 665 (W) x 665 (H) x 355 (D) mm
: 10.6 kg
: 4 uts per carton
HS880 : HIGH POWER HORN SPEAKER
HS880
20” 80W 100V LINE
Constructed using rounded aluminum flare of 20” (HS880) with multiple power
selection. It is suitable for schools, mosques, fencing perimeters etc, which requires
loud and clear broadcast.
Packing information
HS880
: 585 (W) x 390 (H) x 560 (D) mm
: 6.2 kg
: 1 unit per box
HS820 : HORN SPEAKER WITH RECT. FLARE
HS820
6“ X 8” 15W 100V LINE
IP65
Constructed with high impact ABS flares rectangular shape to suit installation sites
where pattern of broadcast shall be controlled, such as low level car parks,
corridors, etc. Suitable for indoor or outdoor sites with IP65 rating.
Packing information
HS820
: 550 (W) x 180 (H) x 465 (D) mm
: 14.2 kg
: 8 uts per carton
Power rating
Power tapping (W)
Primary Impedance (Ohm)
Frequency response (+/-5 dB) @ 1KHz, 1W
SPL (1W / m @ 1 KHz)
Flare material
Flare dimension
Driver enclosure
Weight
Colour
56
HS815
15W 100V
1 / 3 / 5 / 10 / 15
670
1K
2K
3.3 K
10 K
350 ~ 7 KHz
103 dB
8” round
210 x 240 mm
1.55 kg
8
ABS
HS830
30W 100V
3 / 5 / 10 / 15 / 30
330
670
1K
2K
3.3 K
300 ~ 10 KHz
105 dB
Aluminum
12” round
310 x 325 mm
1.85 kg
Beige
HS880
80W 100V
20 / 40 / 60 / 80
500
250
160
125
16
160 ~ 6 KHz
110 dB
HS820
15W 100V
1.9 / 3.8 / 7.5 / 15
5.26 K
2.63 K
1.33 K
667
8
250 ~ 8 KHz
105 dB
20” round
Aluminum Diecast
504 x 335 mm
3.35 kg
160 x 220 mm
ABS
222(W) x 162(H) x 232(D) mm
1.5 kg
ABS
White
amperes
All models with 60 mm depth, suitable for volume controllers with auto transformers.
Enclosures are optional items and to be ordered separately from volume controllers
/ patch panels.
Accessories
Complementary Products
ENCLOSURES
EC7012 : 70 X 120 mm Back enclosure for concealed mounting (steel)
ES7012 : 70 x 120 mm Back enclosure for surface mounting (steel)
EA9090 : 86 x 86 mm Back enclosure for concealed mounting (ABS)
ES9090 : 86 x 86 mm Back enclosure for surface mounting (steel)
Quality XLR connectors are used in the above series. Other brands of inlets are
available upon request.
PATCH PANELS
MR5000 : 5 Way rack mounted female XLR patch panel
MR1000 : 10 Way rack mounted female XLR patch panel
MP1000 : Single inlet wall mounted female XLR patch panel
MP2000 : Double inlet wall mounted female XLR patch panel
Available with standard Amperes mounting ears for harmonious look with other
amperes equipments.
RACK PANELS
Panels are available in black powder epoxy coating.
BP1000 : 1 hu blank panel
BP2000 : 2 hu blank panel
VP1000 : 1 hu ventilation panel
VP2000 : 2 hu ventilation panel
Regulated power adaptor for powering single unit of equipment. Equipments are not
supplied with power adaptor and are to be ordered separately.
POWER SUPPLY
For larger system, we recommend that proper DC supply to be used with relay
changeover for DC back up supply. ie. Amperes PS9400.
PS1205 : 12V 0.5A ac / dc regulated power adaptor
PS2405 : 24V 0.5A ac / dc regulated power adaptor
PS9000 : 24V 4.5A dc switching power supply
SLA batteries are sold in blocks of 24V ( 2 x 12V block ). Above are common
ratings widely used. Other ratings are available upon request.
SLA BATTERIES
We recommend that Constant Voltage with auto current reducing charger to be
used, ie. Amperes BC9740.
MS12 - 26
MS12 - 40
MS12 - 65
MS12 - 100
: 12V 26 Ah Maintenance free SLA battery
DAEWOO12 - 65 : 12V 65 Ah Sealed rechargeable battery
DAEWOO12 - 100 : 12V 100 Ah Sealed rechargeable battery
Fiber optic converter for IP Paging application ( RJ45 to Fiber ) available in single and
multimode fiber cabling.
Operates on 12V DC with power supply adaptor provided.
HTB110 : Multimode fiber connection ( 2 KM )
SC/ST connectors
HTB110S: Single mode fiber connection ( 25 KM )
SC connectors
Physical dimensions : 26 (H) x 71 (W) x 97 (D) mm
FIBER OPTIC CONVERTER
57
Technical Info
amperes
The criterias to be considered in determining the number of speaker required in any installation
shall include:-
Ceiling speaker
Ceiling
4m
1) The ceiling height
2) Acoustical factor of the environment
3) Type of speakers, eg. dispersion angle and SPL level.
4) Expected environment such as factory, office or shopping complex.
3m
Hearing
level
3.5m
2m
coverage angle
In order to hear properly, the sound source from speaker shall be 6 dB above the background
noise.
1m
If the background noise is around 70 dB, such as in a shopping area with average crowd, the
person shall be listening to the speaker sound at approximately 76 dB, at around 1.5 to 2m above
floor level.
Floor Level
If the power input is 3W, the SPL ( 1KHz ) at 2 m from speaker shall be approximately 93 dB. With
music source, the average SPL shall be 3 dB below ; thereby the hearing shall be around 89 dB,
which is rather comfortable level in a shopping mall.
Effective dispersion radius
From this, the coverage area can be estimated ; ie. approximately 7m diameter or 38 sq m.
Further to this, the distance of speaker can be ascertained by dividing the area of the mall to the
area of coverage by each speaker.
FLOOR MAPPING
A general guide to calculate speaker quantity of a floor area. Ceiling height, dispersion angle and
speaker characteristics determine the dispersion radius.
4m
3m
2m
1m
Point of Source
Distance in Metre
93 dB
(Max 102 dB)
87 dB
(Max 96 dB)
81 dB
(Max 90 dB)
78 dB
(Max 84 dB)
SPL CHART
SPL VS DISTANCE
It tells the frequency response of a speaker, measured at 1W
/ m, +/- 3dB at 1 KHz reference point.
A general guideline showing the drop of SPL level over
distance, measured in meter.
POLAR CHART
Shows the effective dispersion angle of a speaker. Full
360 deg chart is often used to check full angular characteristics of speaker.
POSSIBLE CAUSE OF SPEAKER DAMAGE
Speaker may be damaged while in operation and can be associated to excessive power delivery in appropriate frequencies the driver
or due to natural disaster such as lightning strike. To prevent or at least to pro long the speaker lifespan the followings should be taken
into consideration:Avoid excessive input power to speakers
Ensure audio signal delivered is within the frequency baudpass of the speaker ( e.g. sub bass)
Do not allow amplifier to clip, ie ensure power rating of amplifier is higher than the total load
The amplifier with DC output protection, and preferably with high pass and low pass filters
58
Technical Info
amperes
CALCULATING BACK UP BATTERY
CAPACITY
CORRECT WAY OF POWERING EQUIPMENT WITH
24V DC
For most commercial installations, it is a requirement by
local authority that the PA system must be able to operate
during power failure. The means for back up supply to the
system can be from building’s standby generator or via
standalone back up power supply bank ie. Batteries.
It is a misinformed idea to save some equipment
cost in powering up equipment with 24V DC by
using voltage output from battery charger instead
of a 24V DC power supply unit or adaptor. It shall
damage the equipment concerned as normally
they can operate in the range of 10% voltage
tolerance and anything above that shall stress the
power regulating circuitries. Not only it would
shorten the life span but excessive heat would be generated.
Batteries can be NiCd or usually SLA type. Steps below
provide a simple calculation method on the capacity of
batteries required (24V).
Step 1 :
Sum up total current drawn in the system and operating period required using back up
batteries.
ie. Total current drawn under 24V supply is 30A and 2 hrs of full load operation is
required
Capacity C1 : 30 x 2 = 60 Ah
Step 2 :
Residual voltage percentage to remain at batteries to avoid total discharge, which
may cause permanent damage to the cells. ( Refer to manufacturer’s data for safe
value )
Voltage from battery charger is normally around 27 to 28V DC whereas
from power supply unit ie. Amperes PS9400 is regulated at 24V DC.
Thereby it is highly recommended to use suitable regulated power
supply unit for operation.
20V DC 24V DC
26V DC
ie. 30% Voltage to remain
Capacity C2 : 60 / 0.7 = 85.7 Ah
Step 3 :
Determine optimum discharge rate. Discharge rate differs according to the battery
capacity. ( Refer to manufacturer’s data )
PS9400
ie. If it is recommended to draw 5 amp / hour from a battery
Capacity C3 : 85.7 / 0.5 = 171.4 Ah
Step 4 :
BC9740
27.8V DC
Duty cycle may differ according to type of load. Music broadcast has lower duty cycle
as compared to siren. Using a factor of 20% for music,
ie. 20% of current shall be drawn in an hour ie. duty cycle = 20%
BATTERY CAPACITY REQUIRED : 171.4 x 0.2 = 34.28 Ah
Thereby the nearest standard capacity available is 40 Ah, which would be used for the system.
A calculation table is available in Technical Section of www.ampereselectronics.com
SOURCE OF INFO : VARIOUS
First Digit ( Protection fr. Solid Object)
Second Digit ( Protection from liquid)
0
No Protection
0
No Protection
1
Solid object of up to 50 mm and above
1
Vertically falling water drops
2
2
Water spray with 15 vertical angle
3
Solid object of up to 2.5 mm and above
3
Water spray with 60 vertical angle
4
4
Water spray with full all direction with allowance
5
Dust with no harmful deposits
5
Low pressure water jet from all direction
6
Full protection from dust
6
High pressure water jet from all direction
7
Temporary immersion in water
8
Long immersion in water
IP RATINGS
Ingress Protection up is a
classification to indicate the
degree of protection of
enclosures ( such as speakers )
against penetration of solid
particles and moisture.
It is usually stated in two digits,
IP54,
which
the
first
digit refers to protection against solid object and the second
digit for protection from moisture.
Ref Standards : IEC 60529
SOURCE OF INFO : VARIOUS
V
59
15th
Year Of Excellence
Due to our continuous product improvement policy, amperes electronics reserves the rights to change the specifications,
features and artwork without prior notifications.
While every care had been taken to ensure the information contained in this catalogue is correct at the time of printing, some
minor errors may be unintentionally inserted. Kindly contact us for clarifications should any doubt arises. Amperes shall be
indemnified against any claims caused by any errors in the printing.
The “amperes” logo is a registered trademark of Amperes Electronics Sdn Bhd (Co No:509025-X) Malaysia.
Copyrights Reserved @2015
amperes
PUBLIC ADDRESS SYSTEM
C O M M E R C I A L I N S TA L L AT I O N S
20
15
16
ISO 9001: 2008
Related materials such as engineer’s specifications, instruction manuals, product drawings and
catalogue in softcopy are available in CD-ROM and website.
Models which are not available in this version of catalogue are considered discontinued from
production or latest products which are yet launched at the time of printing.
Kindly contact your nearest distributor or e-mail to us for further information.
Distributed By :

Full 2015 / 2016 Amperes Catalogue

Transcription

Similar documents

Product Sheet

USER MANUAL

060504 SL-650 Usermanual final eng.cdr

Moderator: Dr. Art Hister 12:00 – 12:45 pm Food

Full instructions are online here!

kits - audio projects

Evalyn Frondozo - Rex Book Store

Roger`s Two Way Radio

Rock-A-Thon - Little Sisters of the Poor Pittsburgh

RF amplifier PA70E on RD70HVF1