Universal Laptop Mount Set

Universal Laptop Mount
Set-up Instructions
Part # UT-X
Part # UT-X-T
Part # UT-X-ATG
www.havis.com
1-800-524-9900
UT-X-OMN_0410
Before Beginning
Reconfiguring the Universal Laptop Mount
Havis is pleased to provide these set-up instructions to aid in the proper instillation of its
Universal Laptop Mount (UT-X, UT-X-T, or UT-X-ATG). Havis recommends that the UT-X, UT-X-T,
and UT-X-ATG be installed with all four of the Side Hold-down Lugs in place, spaced as far apart
as practical to ensure the safest laptop mount configuration.
Havis also recommends that the UT-X, UT-X-T, and UT-X-ATG be installed with its Front and Rear
Fences in place and that all torque settings be followed (see torque setting references inside
Set-up Instructions). Currently, all torque adjusted screws will utilize the T-25 pin-in torx bit and
should be installed with a calibrated torque wrench set to 22 inch-pounds of torque, +/- 10 %.
NOTE
It is important that the UT-X, UT-X-T, and UT-X-ATG be set with the
Side Trays and Rear Tray fully extended before beginning installation.
Follow the steps below to reconfigure the UT-X, UT-X-T, and UT-X-ATG to its original settings.
Completely close the Side Trays by pressing
them inward until a “click” is heard.
For questions regarding the set-up of your laptop in the UT-X, UT-X-T, or UT-X-ATG, please contact
Havis at 1-800-524-9900 or visit www.havis.com for additional product support and information.
! WARNING
NEVER STOW OR MOUNT THE UT-X, UT-X-T, or UT-X-ATG
DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE.
DO NOT USE COMPUTER WHILE DRIVING.
FIG. O
Loosen the screws
(MARKED A in FIG. P).
A
Pull both Side Trays outward
as far as they will go.
A
Retighten the screws to
22 inch-pounds of torque, +/- 10 %.
Table of Contents
Hardware Kit................................................................................................................................................................2
Preparing the Laptop.................................................................................................................................................2
Getting to Know the Universal Laptop Mount..................................................................................................3
Step 1: Make Sure the Laptop Fits.........................................................................................................................4
FIG. P
Make sure both of the Rear Tray
Adjustment Screws are as far
rearward as possible. See FIG. Q.
Step 2: Replacing the Short Hold-down Lugs - Optional................................................................................5
Step 3: Adjust Side and Rear Trays to Fit the Laptop........................................................................................5
Step 4: Adjusting and Positioning Side Hold-down Lugs...............................................................................7
You can adjust the screw by loosening
it and pulling on the Rear Tray.
Step 5: Custom Configurations..............................................................................................................................8
Step 6: Make Sure the Laptop is Secure..............................................................................................................8
Retighten the screws to
22 inch-pounds of torque, +/- 10 %.
Blocked CD/DVD Drive.............................................................................................................................................9
Questions.....................................................................................................................................................................9
Reconfiguring the Universal Laptop Mount....................................................................................................10
FIG. Q
1
www.havis.com • 1-800-524-9900
10
Blocked CD/DVD Drive
Hardware Kit
If the laptop will need to run a CD/DVD you
simply unlatch the Side Trays by pulling the
latch forward until you hear a click and then
tilt the laptop on an angle until you have
access to the CD/DVD drive.
The hardware kit should include:
1
Return laptop to secure stowed position by
closing the Side Trays.
FIG. N
2
3
4
5
6
7
1. Integrated Zip Tie / Pushpin (4)
2. Star Washer (5)
3. Hex Screws (5)
4. Hold-down Lug Bumpers (4)
5. Hold-down Lug Vinyl Cap (4)
6. L-shaped Wrench
7. Keys for Release Lock (2)
! WARNING
FIG. A
DO NOT USE COMPUTER WHILE DRIVING.
Preparing the Laptop
Make sure you:
Questions?
• Turn the power OFF.
• Remove any cords or peripherals
that are connected to the laptop.
For questions regarding the set-up of
your laptop in the Universal Laptop
Mount (UT-X, UT-X-T, or UT-X-ATG) please
contact Havis at 1-800-524-9900, or visit
www.havis.com for additional product
support and information.
FIG. B
! CAUTION
Leaving devices such as USB flash drives, cords, or air cards connected to the
computer during installation may cause damage to the device and to the laptop.
9
www.havis.com • 1-800-524-9900
2
Getting to Know the Universal Laptop Mount
C
Step 5: Custom Configurations
If any of the Side Hold-down Lugs
or Front/Rear Fences are covering
ports, loosen the screw and gently
slide the Lug or fence along its slot
C
F
as shown in FIG. M.
Retighten the screws to
22 inch-pounds, +/- 10%.
D
D
E
E
D
FIG. M
NOTE
D
If adjusting the Side Hold-down Lugs or Front/Rear Fences does not resolve the interference
with ports or switches DO NOT REMOVE THEM. Contact Havis at 1-800-524-9900
to speak with a technical specialist who can provide further instruction.
A
B
Step 6: Make Sure the Laptop is Secure
B
FIG. C
Part
Description
A
Latch Release Handle
Used to Release Side Trays
B
Front Fences
Front Stops for Laptop
C
Rear Fences
Rear Stops for Laptop
D
Side Hold-down Lugs
Used to Secure Laptop Deck
E
Side Trays
Used to Fit Laptop
F
Rear Tray
Used to Fit Laptop
It is important to make sure
that the laptop is fully secured
in the Universal Laptop Mount.
Final Check List
NOTE
If this is not the first time the UT-X, UT-X-T, or UT-X-ATG has been configured to
fit a laptop please read the section on reconfiguration located on page 10.
Laptop is in contact with the Front Fences.
Side Hold-down Lugs are set to proper height and
are in contact with the deck of the computer.
Laptop is in contact with the Rear Fences.
No vital ports or switches are covered by the
Side Hold-down Lugs or Front/Rear Fences.
3
www.havis.com • 1-800-524-9900
8
Step 3: Adjust Side and Rear Trays to Fit the Laptop - Con’t
Step 1 : Make Sure the Laptop Fits
Loosen screws and push
Rear Tray in until flush
against laptop.
Place the laptop in the UT-X, UT-X-T,
or UT-X-ATG.
Carefully open the laptop screen.
B
Close the Side Trays by pressing
inward (FIG. D).
B
FIG. D
Check to see that the Side Hold-down
Lugs fit over the laptop as in FIG. E.
FIG. K
There should be a slight gap between
the top of the Side Hold-down Lugs
and the laptop deck, this will be
adjusted in Step 4.
Hold the laptop fully forward against the Front Fences, loosen screws
(MARKED B in FIG. K).
Slide the Rear Tray up against the back of the laptop.
Once snug, retighten both adjustment screws to 22 inch-pounds, +/- 10%.
Step 4: Adjusting and Positioning Side Hold-down Lugs
FIG. E
Turn the laptop on its side to adjust
the Side Hold-down Lugs.
If the Side Hold-down Lugs installed
by the factory are too short as in FIG. F,
you will need to perform step 2.
Loosen the screws and adjust the Lug
until it makes firm contact with the
Laptop deck and will hold the Laptop
in place (see FIG. L).
Repeat this step for the remaining
three Side Hold-down Lugs.
FIG. L
7
Turn the entire unit right-side-up
and test the Side Hold-down Lugs to
ensure that they are making contact
with the laptop deck.
www.havis.com • 1-800-524-9900
FIG. F
4
Step 2: Replacing the Short Hold-down Lugs
(Optional for UT-X and UT-X-ATG)
With the laptop secured in the UT-X, UT-X-T,
or UT-X-ATG open the laptop screen.
Carefully place the unit upside-down on
your lap as in FIG. I.
(NOTE: Step 2 not applicable for UT-X-T. Please proceed to Step 3)
Make sure that the laptop is
completely forward and touching
Locate the adjustment screw for each
of the four Side Hold-down Lugs.
the two Front Fences as in FIG. J.
Remove the Lug by loosening the screw
with the provided L-shaped wrench.
See FIG. G.
FIG. G
FIG. I
Take the four Tall Side Hold-down Lugs
from the Hardware Kit and install
the vinyl caps and bumpers on each
Lug as in FIG. H.
Re-install all the Tall Side Hold-down
Lugs into the slots on the UT-X and
UT-X-ATG and tighten the screws until
they are snug.
Loosen screws
and push Side
Trays inward at
the same time so
they are even and
flush against sides
of laptop
A
A
Check to make sure the lugs fit over
the side of the laptop as in FIG. E.
FIG. H
Step 3: Adjust Side and Rear Trays to Fit the Laptop
NOTE
Before beginning this step make sure that the laptop is placed in the UT-X, UT-X-T, or UT-X-ATG
and the Side Trays are fully closed (press Side Trays together until click is heard).
! CAUTION
Use extreme caution when placing the laptop upside-down to adjust the back.
Make sure that you do not damage the laptop screen.
5
www.havis.com • 1-800-524-9900
Laptop should be flush
with Front Fences.
FIG. J
Loosen the screws (MARKED A in FIG. J) approximately one full turn.
(DO NOT REMOVE SCREWS)
With the laptop centered side-to-side in the UT-X, UT-X-T, or UT-X-ATG, slide both Side Trays
at the same time inward until they touch the sides of the laptop as in FIG. J.
Retighten the screws (MARKED A in FIG. J). Torque to 22 inch-pounds, +/- 10%.
6
Step 2: Replacing the Short Hold-down Lugs
(Optional for UT-X and UT-X-ATG)
With the laptop secured in the UT-X, UT-X-T,
or UT-X-ATG open the laptop screen.
Carefully place the unit upside-down on
your lap as in FIG. I.
(NOTE: Step 2 not applicable for UT-X-T. Please proceed to Step 3)
Make sure that the laptop is
completely forward and touching
Locate the adjustment screw for each
of the four Side Hold-down Lugs.
the two Front Fences as in FIG. J.
Remove the Lug by loosening the screw
with the provided L-shaped wrench.
See FIG. G.
FIG. G
FIG. I
Take the four Tall Side Hold-down Lugs
from the Hardware Kit and install
the vinyl caps and bumpers on each
Lug as in FIG. H.
Re-install all the Tall Side Hold-down
Lugs into the slots on the UT-X and
UT-X-ATG and tighten the screws until
they are snug.
Loosen screws
and push Side
Trays inward at
the same time so
they are even and
flush against sides
of laptop
A
A
Check to make sure the lugs fit over
the side of the laptop as in FIG. E.
FIG. H
Step 3: Adjust Side and Rear Trays to Fit the Laptop
NOTE
Before beginning this step make sure that the laptop is placed in the UT-X, UT-X-T, or UT-X-ATG
and the Side Trays are fully closed (press Side Trays together until click is heard).
! CAUTION
Use extreme caution when placing the laptop upside-down to adjust the back.
Make sure that you do not damage the laptop screen.
5
www.havis.com • 1-800-524-9900
Laptop should be flush
with Front Fences.
FIG. J
Loosen the screws (MARKED A in FIG. J) approximately one full turn.
(DO NOT REMOVE SCREWS)
With the laptop centered side-to-side in the UT-X, UT-X-T, or UT-X-ATG, slide both Side Trays
at the same time inward until they touch the sides of the laptop as in FIG. J.
Retighten the screws (MARKED A in FIG. J). Torque to 22 inch-pounds, +/- 10%.
6
Step 3: Adjust Side and Rear Trays to Fit the Laptop - Con’t
Step 1 : Make Sure the Laptop Fits
Loosen screws and push
Rear Tray in until flush
against laptop.
Place the laptop in the UT-X, UT-X-T,
or UT-X-ATG.
Carefully open the laptop screen.
B
Close the Side Trays by pressing
inward (FIG. D).
B
FIG. D
Check to see that the Side Hold-down
Lugs fit over the laptop as in FIG. E.
FIG. K
There should be a slight gap between
the top of the Side Hold-down Lugs
and the laptop deck, this will be
adjusted in Step 4.
Hold the laptop fully forward against the Front Fences, loosen screws
(MARKED B in FIG. K).
Slide the Rear Tray up against the back of the laptop.
Once snug, retighten both adjustment screws to 22 inch-pounds, +/- 10%.
Step 4: Adjusting and Positioning Side Hold-down Lugs
FIG. E
Turn the laptop on its side to adjust
the Side Hold-down Lugs.
If the Side Hold-down Lugs installed
by the factory are too short as in FIG. F,
you will need to perform step 2.
Loosen the screws and adjust the Lug
until it makes firm contact with the
Laptop deck and will hold the Laptop
in place (see FIG. L).
Repeat this step for the remaining
three Side Hold-down Lugs.
FIG. L
7
Turn the entire unit right-side-up
and test the Side Hold-down Lugs to
ensure that they are making contact
with the laptop deck.
www.havis.com • 1-800-524-9900
FIG. F
4
Getting to Know the Universal Laptop Mount
C
Step 5: Custom Configurations
If any of the Side Hold-down Lugs
or Front/Rear Fences are covering
ports, loosen the screw and gently
slide the Lug or fence along its slot
C
F
as shown in FIG. M.
Retighten the screws to
22 inch-pounds, +/- 10%.
D
D
E
E
D
FIG. M
NOTE
D
If adjusting the Side Hold-down Lugs or Front/Rear Fences does not resolve the interference
with ports or switches DO NOT REMOVE THEM. Contact Havis at 1-800-524-9900
to speak with a technical specialist who can provide further instruction.
A
B
Step 6: Make Sure the Laptop is Secure
B
FIG. C
Part
Description
A
Latch Release Handle
Used to Release Side Trays
B
Front Fences
Front Stops for Laptop
C
Rear Fences
Rear Stops for Laptop
D
Side Hold-down Lugs
Used to Secure Laptop Deck
E
Side Trays
Used to Fit Laptop
F
Rear Tray
Used to Fit Laptop
It is important to make sure
that the laptop is fully secured
in the Universal Laptop Mount.
Final Check List
NOTE
If this is not the first time the UT-X, UT-X-T, or UT-X-ATG has been configured to
fit a laptop please read the section on reconfiguration located on page 10.
Laptop is in contact with the Front Fences.
Side Hold-down Lugs are set to proper height and
are in contact with the deck of the computer.
Laptop is in contact with the Rear Fences.
No vital ports or switches are covered by the
Side Hold-down Lugs or Front/Rear Fences.
3
www.havis.com • 1-800-524-9900
8
Blocked CD/DVD Drive
Hardware Kit
If the laptop will need to run a CD/DVD you
simply unlatch the Side Trays by pulling the
latch forward until you hear a click and then
tilt the laptop on an angle until you have
access to the CD/DVD drive.
The hardware kit should include:
1
Return laptop to secure stowed position by
closing the Side Trays.
FIG. N
2
3
4
5
6
7
1. Integrated Zip Tie / Pushpin (4)
2. Star Washer (5)
3. Hex Screws (5)
4. Hold-down Lug Bumpers (4)
5. Hold-down Lug Vinyl Cap (4)
6. L-shaped Wrench
7. Keys for Release Lock (2)
! WARNING
FIG. A
DO NOT USE COMPUTER WHILE DRIVING.
Preparing the Laptop
Make sure you:
Questions?
• Turn the power OFF.
• Remove any cords or peripherals
that are connected to the laptop.
For questions regarding the set-up of
your laptop in the Universal Laptop
Mount (UT-X, UT-X-T, or UT-X-ATG) please
contact Havis at 1-800-524-9900, or visit
www.havis.com for additional product
support and information.
FIG. B
! CAUTION
Leaving devices such as USB flash drives, cords, or air cards connected to the
computer during installation may cause damage to the device and to the laptop.
9
www.havis.com • 1-800-524-9900
2
Before Beginning
Reconfiguring the Universal Laptop Mount
Havis is pleased to provide these set-up instructions to aid in the proper instillation of its
Universal Laptop Mount (UT-X, UT-X-T, or UT-X-ATG). Havis recommends that the UT-X, UT-X-T,
and UT-X-ATG be installed with all four of the Side Hold-down Lugs in place, spaced as far apart
as practical to ensure the safest laptop mount configuration.
Havis also recommends that the UT-X, UT-X-T, and UT-X-ATG be installed with its Front and Rear
Fences in place and that all torque settings be followed (see torque setting references inside
Set-up Instructions). Currently, all torque adjusted screws will utilize the T-25 pin-in torx bit and
should be installed with a calibrated torque wrench set to 22 inch-pounds of torque, +/- 10 %.
NOTE
It is important that the UT-X, UT-X-T, and UT-X-ATG be set with the
Side Trays and Rear Tray fully extended before beginning installation.
Follow the steps below to reconfigure the UT-X, UT-X-T, and UT-X-ATG to its original settings.
Completely close the Side Trays by pressing
them inward until a “click” is heard.
For questions regarding the set-up of your laptop in the UT-X, UT-X-T, or UT-X-ATG, please contact
Havis at 1-800-524-9900 or visit www.havis.com for additional product support and information.
! WARNING
NEVER STOW OR MOUNT THE UT-X, UT-X-T, or UT-X-ATG
DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE.
DO NOT USE COMPUTER WHILE DRIVING.
FIG. O
Loosen the screws
(MARKED A in FIG. P).
A
Pull both Side Trays outward
as far as they will go.
A
Retighten the screws to
22 inch-pounds of torque, +/- 10 %.
Table of Contents
Hardware Kit................................................................................................................................................................2
Preparing the Laptop.................................................................................................................................................2
Getting to Know the Universal Laptop Mount..................................................................................................3
Step 1: Make Sure the Laptop Fits.........................................................................................................................4
FIG. P
Make sure both of the Rear Tray
Adjustment Screws are as far
rearward as possible. See FIG. Q.
Step 2: Replacing the Short Hold-down Lugs - Optional................................................................................5
Step 3: Adjust Side and Rear Trays to Fit the Laptop........................................................................................5
Step 4: Adjusting and Positioning Side Hold-down Lugs...............................................................................7
You can adjust the screw by loosening
it and pulling on the Rear Tray.
Step 5: Custom Configurations..............................................................................................................................8
Step 6: Make Sure the Laptop is Secure..............................................................................................................8
Retighten the screws to
22 inch-pounds of torque, +/- 10 %.
Blocked CD/DVD Drive.............................................................................................................................................9
Questions.....................................................................................................................................................................9
Reconfiguring the Universal Laptop Mount....................................................................................................10
FIG. Q
1
www.havis.com • 1-800-524-9900
10
Universal Laptop Mount
Set-up Instructions
Part # UT-X
Part # UT-X-T
Part # UT-X-ATG
www.havis.com
1-800-524-9900
UT-X-OMN_0410