Blasthole Drilling

BLASTHOLE DRILLS
Blasthole Drilling
in Open Pit Mining
Rotary blasthole drills
Atlas Copco offers the most comprehensive line of rotary blasthole drills in the industry. With a multitude of
configurations to choose from, you can find the perfect
solution for your needs. Many models can be configured
for either rotary or DTH drilling, and our blasthole products will drill holes from 4 inches to 16 inches in
diameter.
Third edition 2012
www.atlascopco.com/blastholedrills
On the following pages, you will find basic specifications
and brief descriptions of the standard and optional equipment available for each model. The different configurations of drill rigs and drill strings make it possible to find
high-performing solutions for a variety of applications.
Safety and ergonomic design with operator comfort and
well-being in mind, as well as simplicity in maintenance,
have been a focus for many years – and are still top
priorities.
When selecting your drill rig, you may have a choice
between high-pressure compressors for DTH drilling or
low-pressure units for rotary drilling, and between diesel
or electric power units. Depending on the drilling pattern
and bench height, you can select between drills suitable
for angle drilling or single- and multi-pass drilling.
Some rig models, like the T4BH and the DM series
that use conventional control systems, are well known
throughout the mining community for their rugged and
reliable designs.The newer Pit Viper series, with its more
advanced designs, can be equipped with the RCS computerized network control system which offers possibilities for different levels of drill automation and communication.
This is only a basic guide. Our product specialists around
the world are prepared to provide you with the information you need to select the best drill and drill string
package to suit your specific application.
BLASTHOLE DRILLS
BLASTHOLE DRILLS
DM25-SP
Technical data
The Atlas Copco DM25-SP is a crawler mounted, selfpropelled, hydraulic rotary table drive, single-pass rotary
drilling rig specifically designed for 4 in. to 6¾ in. (102
mm to 171 mm) blasthole applications to depths of up to
40 ft. (12.2 m) or 50 ft. (15.2 m) of clean hole, depending
on tower selection with either rotary or down-the-hole
drilling. Feed pressure generates a pulldown force of up
to 25,000 lbf (111 kN). The optional angle drilling package
allows the tower to be positioned up to a maximum of
15° from the vertical in increments of 5°. All controls for
positioning are located at the operator´s control console
inside the cab. The package includes a drill pipe support.
Standard equipment
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
3PACIOUSTHERMALINSULATEDANDSOUNDATTENUATEDCAB
#ABPRESSURIZERHEATER
(YDRAULICALLYRETRACTABLEDUSTHOODWITHSKIRTING
.INEQUARTZHALOGENNIGHTLIGHTINGPACKAGE
#OOLINGPACKAGERATEDUPTOª&ª#AMBIENT
temperature
(EAVYDUTYENGINESILENCERMUFmER
3EPARATEAIRINTAKElLTERSFORENGINEANDCOMPRESSOR
2EMOTEHYDRAULICTOWERPINNING
(YDRAULICALLYPOWEREDAUXILIARYCHAINWRENCH
(Down-the-hole units only)
'ALLON,ITERFUELTANK
(YDRAULICSPURGEARANDPLANETARYDRIVEROTARYTABLE
with 0 to 170 RPM and a maximum torque of 3,500 lbfsft
4HREEINMMSTROKELEVELINGJACKSWITHIN
(457 mm) pads
LBKG'67RATEDEXCAVATORTYPE
undercarriage
INMMWIDETRIPLEBARGROUSERS
3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
2EINFORCEDRECTANGULARSTEELTRACKFRAMEWITH
oscillation yoke mounting
&ULLLENGTHKELLYBARANDKELLYSUB
$ECKSERVICECATWALKWITHRAILINGS
"ACKUPALARM
Drilling Method
Rotary or DTH - Single pass
Hole Diameter
4 in - 7 in
102 mm - 178 mm
Hydraulic Pulldown
25,000 lbf
111 kN
Weight on bit
25,000 lb
11,300 kg
Hydraulic Pullback
25,000 lbf
111 kN
Single pass depth
40 ft or 50 ft 12.2 m or 15.2 m
Maximum hole
depth
40 ft or 50 ft 12.2 m or 15.2 m
Feed speed
72 ft/min
0.36 m/s
Rotary table, torque
3,500 Ibfsft
4.7 kNm
Estimated weight
62,000 lb
28 tonnes
Dimensions tower up (50 ft tower)
Length
30 ft 6 in
9.3 m
Height
74 ft
22.6 m
Width
12 ft 8 in
3.9 m
Dimensions tower down (50 ft tower)
Length
72 ft
21.9 m
Height
13 ft
4.0 m
Compressor range
Low pressure, Rotary 900 cfm@110 psi 25.4 m3/[email protected] bar
High pressure, DTH
900 cfm@350 psi 25.4 m3/min@24 bar
Engine (Tier III)
Caterpillar
C15
425HP / 317 kW@1800RPM (LP 900)
Cummins
QSX15
425HP / 317 kW@1800RPM (LP 900)
Caterpillar
C15
525HP / 391 kW@1800RPM (HP 900)
Cummins
QSX15
525HP / 391 kW @1800RPM (HP 900)
Kelly specifications
Hole depth*
Kelly
diameter
Suggested bit
diameters
Thread**
size and
type
40 ft (12.2 m)
2 7/8" (73 mm)
4" - 5 1/2"
2 3/8" IF
3 3/4" (95 mm)
5 1/2" - 7"
2 7/8" API
4 3/4"
(121 mm)
5 7/8" - 7"
3 1/2" API
2 7/8"
(73 mm)
4" - 5 1/2"
2 3/8" IF
3 3/4"
(95 mm)
5 1/2" - 6 1/4"
2 7/8" API
5 7/8" - 7"
3 1/2" API
50 ft (15.2 m)
4 3/4" (121 mm)
* Clean hole ** All kellys have pin connections on both ends
High pressure DTH drilling
Up to 6" DTH hammer and max. 7" bit diameter
DM25
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
DM30
Technical data
The Atlas Copco DM30 is a crawler mounted, hydraulic
tophead drive, muliti-pass rotary drilling rig specifically
designed for production blasthole drilling to depths of
90 ft. (27.4 m) with a 30 ft. (9.1 m) drill pipe change.
A four-position drill pipe changer is optionally available
to achieve drilling depths of 150 ft. (57.7 m). Nominal
hole size is 5 in. to 6¾ in. (127 mm to 171 mm). The
DM30 generates a bit load force of up to 30,000 lbf
(133 kN). The optional angle drilling package allows the
tower to be positioned up to a maxuimum of 20º from
the vertical in increments of 5º. Designed for quarrying
and small mining operations, this versatile drill can be
easily loaded onto a trailer and moved from one
location to another.
Standard equipment
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Spacious, thermal insulated and sound-attenuated cab
#ABPRESSURIZERHEATERVENTILATOR
(YDRAULICALLYRAISEDDUSTHOODWITHSKIRTING
.INEQUARTZHALOGENNIGHTLIGHTINGPACKAGE
!UXILIARYHOISTFORDRILLPIPEANDACCESSORYHANDLING
#OOLINGPACKAGERATEDUPTOª&ª#AMBIENT
(EAVYDUTYENGINESILENCERMUFmER
3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
2EMOTEHYDRAULICTOWERPINNING
0OWERINDEXEDCAROUSELFORTWOžORIN
/$XFTDRILLRODS
2EMOTEHYDRAULICFORKCHUCKFORDRILLPIPEBREAKOUT
(YDRAULICALLYPOWEREDAUXILIARYCHAINWRENCH
GALLONLFUELTANK
2OTARYHEADWITHSINGLElXEDDISPLACEMENTMOTORWITH
0 to 100 RPM available, and a maximum torque of
5,400 lbfsft
4HREEINMMSTROKELEVELINGJACKS
LBKG'67RATEDEXCAVATORTYPE
undercarriage
INMMWIDETRIPLEBARGROUSERS
2EINFORCEDRECTANGULARSTEELTRACKFRAMEWITH
oscillation yoke mounting
$ECKSERVICECATWALKWITHRAILINGS
"ACKUPALARM
Drilling Method
Rotary or DTH - Multi pass
Hole Diameter
5 in - 6 3/4 in
127 mm - 171 mm
Hydraulic Pulldown
30,000 lbf
133 kN
Weight on bit
30,000 lb
13,600 kg
Hydraulic Pullback
10,000 lbf
44 kN
Single pass depth
26 ft
7.9 m
Maximum hole depth 150 ft
45 m
Feed speed
100 ft/min
0.5 m/s
Rotary head, torque
5,400 Ibfsft
7.3 kNm
Estimated weight
60,000 lb
28 tonnes
Dimensions tower up
Length
24 ft 4 in
7.4 m
Height
44 ft 4 in
13.5 m
Width
11 ft 10 in
3.6 m
Dimensions tower down
Length
42 ft 2 in
12.9 m
Height
14 ft 6 in
4.4 m
Compressor range
Low pressure, Rotary
900 cfm@110 psi 25.4 m3/[email protected] bar
High pressure, DTH
900 cfm@350 psi 25.4 m3/min@24 bar
Engine (Tier III)
Caterpillar
C15
425HP / 317 kW@1800RPM (LP 900)
Cummins
QSX15
425HP / 317 kW@1800RPM (LP 900)
Caterpillar
C15
525HP / 391 kW@1800RPM (HP 900)
Cummins
QSX15
525HP / 391 kW@1800RPM (HP 900)
Drill pipe specification: 30 ft (9.1m)
Drill pipe diameter
Suggested bit
diameters - rotary
Thread
4" (102 mm)
5" – 6"
2 7/8" API
4 ½" (114 mm)
5 7/8" – 6 3/4"
3 1/2" API
5" (127 mm)
6 3/4"
!0)OR"%#/
High pressure DTH drilling
Up to 6" DTH hammer and max. 6 ¾" bit diameter
DM30
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
DM30 II
Technical data
Drilling Method
Drilling Method DTH - Multi pass
Hole Diameter
5 in - 6 3/4 in
127 mm - 171 mm
Hydraulic Pulldown
30,000 lbf
133 kN
Drilling Method
Rotary - Multi pass
Hole Diameter
5 in - 7 7/8 in
127 mm - 200 mm
Hydraulic Pulldown
30,000 lbf
133 kN
Weight on bit
30,000 lb
13,600 kg
Hydraulic Pullback
10,000 lbf
44 kN
Single pass depth
26 ft
7.9 m
Maximum hole
depth
150 ft
45 m
Feed speed
100 ft/min
0.5 m/s
Rotary head, torque
)BFsFT
7.3 kNm
Major upgrades
Estimated weight
70,000 lb
31.5 tonnes
s .EWLARGERTHERMALINSULATEDCABINMOUNTEDONTHERIGHT
side of the carrier(seen from the drill end)
s %LECTRICOVERHYDRAULICCONTROLSYSTEMSIMILARTOWHATIS
used on other rigs in the DM-series
s /PTIONALWALKWAYANDENLARGEDDECKAREAFOR
improved access to service and maintenance.
s )MPROVEDOPTIONALANGLEDRILLINGPACKAGEALLOWSTHE
tower to be positioned up to a maximum of 30º from the
vertical in increments of 5º
s New long life main frame designed with I-beams, featuring
oscillation yoke mounting.
s %NLARGEDHYDRAULICALLYRAISEDDUSTHOODWITHSKIRTING
provide more space for cuttings.
s .EWDESIGNWITHHYDRAULICMOTORFORCAROUSELINDEXING
s /PTIONAL!TLAS#OPCOSCREWTYPELOWANDHIGHPRESSURE
compressor, with high air temperature shut down.
s .EWSECTIONDIRECTIONALVALVESYSTEM
s 3TANDARDCENTRALLUBRICATIONMANIFOLD
Dimensions tower up
The Atlas Copco DM30 II is an improved and upgraded
version of the DM30. It is a crawler mounted, hydraulic
tophead drive, muliti-pass rotary drilling rig specifically
designed for production blasthole drilling to depths of
90 ft. (27.4 m) with a 30 ft. (9.1 m) drill pipe change.
A four-position drill pipe changer is optionally available
to achieve drilling depths of 150 ft. (45.7 m). Nominal
hole size is 5 in. to 7-7/8 in. (127 mm to 200 mm). The
DM30 II generates a bit load force of up to 30,000 lbf
(133 kN). The optional angle drilling package allows the
tower to be positioned up to a maxuimum of 30° from
the vertical in increments of 5°. Designed for quarrying
and small mining operations, this versatile drill can be
easily loaded onto a trailer and moved from one
location to another.
Standard equipment
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
#ABPRESSURIZERHEATERVENTILATOR
%LEVENQUARTZHALOGENNIGHTLIGHTINGPACKAGE
!UXILIARYHOISTFORDRILLPIPEANDACCESSORYHANDLING
#OOLINGPACKAGERATEDUPTOª&ª#AMBIENT
(EAVYDUTYENGINESILENCERMUFmER
3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
2EMOTEHYDRAULICTOWERPINNING
(YDRAULICINDEXEDCAROUSELFORTWOžORžIN
/$XFTDRILLRODS
2EMOTEHYDRAULICFORKCHUCKFORDRILLPIPEBREAKOUT
(YDRAULICALLYPOWEREDAUXILIARYCHAINWRENCH
GALLONLFUELTANK
2OTARYHEADWITHSINGLElXEDORVARIABLEDISPLACEMENT
motor with 0 to 160 RPM available, and a maximum torque
OFLBFsFT
4HREEINMMSTROKELEVELINGJACKS
LBKG'67RATEDEXCAVATORTYPE
undercarriage
INMMWIDETRIPLEBARGROUSERS
2EINFORCEDRECTANGULARSTEELTRACKFRAMEWITHOSCILLATION
yoke mounting
$ECKSERVICECATWALKWITHRAILINGS
"ACKUPALARM
Length
28 ft 7 in
8.7 m
Height
45 ft 2 in
13.8 m
Width
16 ft 11 in
5.2 m
Dimensions tower down
Length
44 ft 11 in
13.7 m
Height
16 ft 8 in
5.1 m
Compressor range
Low pressure
Rotary 1050 cfm@110 psi 29.7 m3/[email protected] bar
High pressure
DTH 900 cfm@350 psi 25.4 m3/min@24 bar
Engine (Tier III)
Caterpillar
C15
475HP / 354 kW@1800RPM (LP 1050)
Caterpillar
C15
525HP / 391 kW@1800RPM (HP 900)
Drill Pipe specification: 30 ft (9.1m)
Drill pipe diameter
Suggested bit
diameters rotary
Thread
4 1/2" (114 mm)
5 7/8" – 6 3/4"
3 1/2" API
5" (127 mm)
6 3/4"
!0)OR"%#/
5 1/2" (140 mm)
7 7/8"
"%#/
High pressure DTH drilling
Up to 6" DTH hammer and max. 6 3/4" bit diameter
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
T4BH
Technical data
Drilling Method
The Atlas Copco T4BH is synonymous with mobility,
power, performance, and productivity. Mounted on a
custom carrier, the T4BH is designed to perform in rough
terrain and has been the leading blasthole drill in its class
in the quarry and mining industries for over 35 years. The
T4BH is a truck mounted, hydraulic tophead drive, multipass rotary drilling rig specifically designed for production
blasthole drilling to depths of 150 ft. (45.7 m) with a 25 ft.
(7.6 m) drill pipe change. An optional 30 ft (9.1m) tower
is also available with the 8 x 4 carrier option.
5 5/8 in - 9 7/8 in
143 mm - 251 mm
Hydraulic Pulldown
30,000 lbf
133 kN
Weight on bit
30,000 lb
13,600 kg
Hydraulic Pullback
22,000 lbf
97 kN
Single pass depth
22 ft 6 in or 27 ft 6 in
6.8 m or 8.4 m
Maximum hole depth*
147 ft 6 in or 177 ft 6 in
45 m or 54.1 m
Feed speed
60 ft/min
0.3 m/s
Rotary head, torque
6,000 Ibfsft
7,165 Ibfsft
8.8 kNm
9.7 kNm
Estimated weight
58,000 lb
26 tonnes
Standard equipment
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
Spacious, thermal insulated sound-attenuated cab
3IXQUARTZHALOGENNIGHTLIGHTINGPACKAGE
2ECTANGULARDUSTHOODWITHSKIRTING
!UXILIARYHOISTFORDRILLPIPEANDACCESSORYHANDLING
#OOLINGPACKAGERATEDUPTOª&ª#AMBIENT
(EAVYDUTYENGINESILENCERMUFmER
3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
0OWERINDEXEDCAROUSELFORlVEžIN/$XFTPIPE
2EMOTEHYDRAULICFORKCHUCKFORDRILLPIPEBREAKOUT
(YDRAULICALLYPOWEREDAUXILIARYCHAINWRENCH
'ALLON,ITER&UELTANK
36SPURGEARMOTORROTARYTOPHEADWITH
0 to 160 RPM, and maximum torque 6,500 lbfsft
4HREEINMMSTROKELEVELINGJACKS
#USTOMDESIGNEDAXLECARRIERWITHHPK7
diesel engine, 10-speed transmission and 16 in.
MMWIDEmANGE(BEAMFRAME
2EMOTETOWERPINNING
"ACKUPALARM
DTH or Rotary - Multi pass
Hole Diameter
Dimensions tower up (25 ft tower)
Length
28 ft 8 in
8.1 m
Height
36 ft 6 in
11.1 m
Width
8 ft
2.4 m
Dimensions tower down (25 ft tower)
Length
35 ft 0 in
10.7 m
Height
13 ft 6 in
4.1 m
Compressor range
High pressure, DTH
900 cfm@350 psi 25.4 m3/min@24 bar
High pressure, DTH
1070 cfm@350 psi 30.3 m3/min@24 bar
High pressure, DTH
1250 cfm@350 psi 35.4 m3/min@24 bar
Engine (2TierII, 3Tier III)
Cummins
QSX153
525HP / 391 kW@1800RPM (HP 900)
Cummins
QSX153
600HP / 447 kW@1800RPM (HP 1070)
Cummins
QSK19C2
760HP / 567 kW@1800RPM (HP 1250)
Drill pipe specification: 25 ft (7.6 m)
Drill pipe diameter
Suggested bit diameters Thread
4"
5 5/8" – 6"
(102 mm)
2 7/8" API
4 1/2" (114 mm)
5 7/8" – 6 3/4"
3 1/2" API
5"
(127 mm)
6 3/4" – 7 3/8"
3 1/2" API
OR"%#/
5 1/2" (140 mm)
6 3/4" – 7 7/8"
"%#/
6 1/4" (159 mm)
7 7/8" – 9"
"%#/
7"
9"-9 7/8"
"%#/
(178 mm)
High pressure DTH drilling
Up to 8" DTH hammer and max. 9 7/8" bit diameter
-AXIMUMHOLEDEPTHONLYACHIEVEDWITHCERTAINPIPESIZESAND
wall thicknesses
T4BH
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
DM45/DM50
The Atlas Copco DM45 and DM50 are crawler mounted,
hydraulic tophead drive, multi-pass rotary drilling rigs
specifically designed for production rotary or DTH
blasthole drilling to depths of 175 ft. (53.3 m) with a 30 ft.
(9.1 m) drill pipe change.
Standard equipment
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
)NSULATEDCABWITH&/03D"!
#ABPRESSURIZERVENTILATORHEATER
.INEQUARTZHALOGENNIGHTLIGHTINGPACKAGE
$USTHOODWITHCURTAINSANDHYDRAULICALLYRAISING
DUSTmAP
!UXILIARYHOISTFORDRILLPIPEANDACCESSORYHANDLING
(EAVYDUTYENGINESILENCERMUFmER
3EPARATEAIRINTAKElLTERSWITHQUICKRELEASEDUSTDROP
covers for engine and air compressor
'EARINDEXINGCAROUSELFORlVEžINXFTPIPE
3LIDINGHYDRAULICFORKWRENCHFORDRILLPIPEBREAKOUT
(YDRAULICALLYPOWEREDAUXILIARYCHAINWRENCH
GALLON,FUELTANK
36TWOMOTORHIGHSPEEDROTARYHEADWITH
spline lubrication, 0 to 160 RPM, and a maximum
torque 7,200 lbfsft
FOOTDRILLPIPECHANGE
.OBUMPRODCHANGER
%THERINJECTION
*ACKUPINDICATORLIGHTS
4HREEINMMSTROKELEVELINGJACKS
INMMWIDETRIPLEBARGROUSERS
2EINFORCEDRECTANGULARSTEELTRACKFRAMEWITH
oscillation yoke
7ALKWAYSANDRAILINGS
2EMOTETOWERPINNING
"ACKUPALARM
Technical data
Drilling Method
Rotary or DTH Multi pass
Hole Diameter
5 7/8 in - 9 in
149 mm - 229 mm
Hydraulic Pulldown
45,000 lbf
200 kN
Weight on bit
45,000 lb
20,400 kg
Hydraulic Pullback
22,000 lbf
98 kN
Single pass depth
27 ft 5 in
Maximum hole depth* 175 ft
8.5 m
53.3 m
Feed speed
146 ft/min
0.7 m/s
Rotary head, torque
7,200 Ibfsft
9,76 kNm
Estimated weight
77,000 lb 95,000 lb
35 tonnes 41 tonnes
Length
31 ft 10 in
9.7 m
Height
43 ft 7 in
13.3 m
Width
17 ft 2 in
5.23 m
Dimensions tower up
Dimensions tower down
Length
43 ft 7 in
13.3 m
Height
18 ft
5.5 m
Compressor range
Low pressure, Rotary 900 cfm@110 psi 25.4 m3/[email protected] bar
Low pressure, Rotary 1050 cfm@110 psi 29.7 m3/[email protected] bar
Low pressure, Rotary 1200 cfm@110 psi 34.0 m3/[email protected] bar
High pressure, DTH
900 cfm@350 psi 25.4 m3/min@24 bar
High pressure, DTH
1070 cfm@350 psi 30.3 m3/min@24 bar
Engine (Tier III)
Caterpillar
C15
440HP / 328 kW@1800RPM (LP 900)
Cummins
QSX15
425HP / 317 kW@1800RPM (LP 900)
Caterpillar
C15
475HP / 354 kW@1800RPM (LP 1050)
Cummins
QSX15
475HP / 354 kW@1800RPM (LP 1050)
Caterpillar
C15
540HP / 403 kW@1800RPM (LP 1200)
Cummins
QSX15
530HP / 395 kW@1800RPM (LP 1200)
Caterpillar
C15
540HP / 403 kW@1800RPM (HP 900)
Cummins
QSX15
530HP / 395 kW@1800RPM (HP 900)
Caterpillar
C18
630HP / 470 kW@1800RPM (HP 1070)
Cummins
QSX15
600HP / 447 kW@1800RPM (HP 1070)
Drill pipe specification: 30 ft (9.1 m)
Drill pipe diameter
Suggested bit
diameters
Thread
4 1/2" (114 mm)
5 7/8" – 6 3/4"
3 1/2" API
5"
(127 mm)
6 3/4" – 7 3/8"
!0)OR"%#/
5 1/2" (140 mm)
6 3/4" – 7 7/8"
"%#/
6 1/4" (159 mm)
7 7/8" – 9"
"%#/
7"
9"
"%#/
(178 mm)
High pressure DTH drilling (DM45)
Up to 6 1/2" DTH hammer and max. 8" bit diameter
DM45
-AXIMUMHOLEDEPTHONLYACHIEVEDWITHCERTAINPIPESIZESAND
wall thicknesses
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
DML-SP
The Atlas Copco DML-SP is a crawler-mounted, hydraulic
table drive, single-pass rotary drilling rig, specifically
designed for production blasthole drilling to depths of
up to 60 ft. (18.3 m) in a single pass without a drill pipe
change. Nominal hole size range is 6 to 9-7/8 in. (152 to
251 mm) for rotary bit applications. The DML-SP has the
option for a 50 ft (15.2 m) clean hole tower or a 60 ft
(18.3 m) clean hole tower.
Standard equipment
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
)NSULATEDCABWITH&/03
#ABPRESSURIZERHEATER
.INEQUARTZHALOGENNIGHTLIGHTINGPACKAGE
2ECTANGULARDUSTHOODWITHSKIRTINGANDHYDRAULICALLY
retractable front curtain
#OOLERPACKAGERATEDUPTOª&ª#AMBIENT
temperature
(EAVYDUTYENGINESILENCERMUFmER
3EPARATEAIRINTAKElLTERSWITHQUICKRELEASEDUSTDROP
covers for engine and air compressor
(YDRAULICALLYPOWEREDAUXILIARYCHAINWRENCH
GALLONLFUELCAPACITY
3INGLEMOTORROTARYTABLEWITHVARIABLEHYDRAULIC
motor (0-100 RPM) and a maximum torque of 7,500 lbfsft
(YDROSTATICMOTORFEEDSYSTEM
4HREEINCMSTROKELEVELINGJACKS
INMMWIDETRIPLEBARGROUSERS
2EINFORCEDRECTANGULARSTEELTRACKFRAMEWITHOSCILLATION
yoke mounting
7ALKWAYSANDDECKRAILINGS
&ULLDEPTHKELLYBAR
+ELLY20-TACHOMETERONCONSOLE
2EMOTETOWERPINNING
"ACKUP!LARM
%THERINJECTION
*ACKUPINDICATORLIGHTS
Technical data
Drilling Method
Rotary or DTH - Single pass
Hole Diameter
6 in - 9 7/8 in
152 mm - 251 mm
Hydraulic Pulldown
54,000 lbf
240 kN
Weight on bit
54,000 lb
24,500 kg
Hydraulic Pullback
54,000 lbf
240 kN
Single pass depth
50 ft or 60 ft
15.2 m or 18.3 m
Maximum hole depth
50 ft or 60 ft
15.2 m or 18.3 m
Feed speed
100 ft/min
0.5 m/s
Rotary table, torque
7,500 Ibfsft
10.2 kNm
Estimated weight
90,000 -100,000 lb
41 - 45 tonnes
Length (50 ft tower)
37 ft 6 in
11.4 m
Length (60 ft tower)
37 ft 6 in
11.4 m
Height (50 ft tower)
71 ft 7 in
21.8 m
Height (60 ft tower)
82 ft 7 in
25.2 m
Width
13 ft 10 in
4.1 m
Dimensions tower up
Dimensions tower down
Length (50 ft tower)
68 ft
Length (60 ft tower)
79 ft
20.7 m
24.1 m
Height (50 ft tower)
19 ft 7 in
6.0 m
Height (60 ft tower)
19 ft 7 in
6.0 m
Compressor range
Low pressure rotary
1,200 cfm@110psi / 34.0 m3/[email protected] bar
Low pressure rotary
1,600 cfm@110psi / 45.0 m3/[email protected] bar
Low pressure rotary
1,900 cfm@110psi / 53.8 m3/[email protected] bar
High pressure, DTH
1,250 cfm@350psi / 35.4 m3/min@24 bar
Engine (2 TierII, 3 Tier III)
Caterpillar C153
Cummins
525HP / 391 kW@1800RPM (LP 1200)
QSX153
Caterpillar C183
Cummins
630HP / 470 kW@1800RPM (LP 1600)
QSX153
Caterpillar C272
Cummins
600HP / 447 kW@1800RPM (LP 1600)
800HP / 597 kW@1800RPM (LP 1900)
QSK192
Caterpillar C272
Cummins
525HP / 391 kW@1800RPM (LP 1200)
755HP / 563 kW@1800RPM (LP 1900)
800HP / 597 kW@1800RPM (HP 1250)
QSK19C2
760HP / 567 kW@1800RPM (HP 1250)
Kelly specifications
Hole depth*
Kelly
diameter
Suggested bit
diameters
50 ft. (15.2 m)
or
60 ft. (18.3 m)
4 3/4 in. (121 mm) 6" – 6 3/4"
Thread**
size and type
3 1/2 in. Reg.
6 1/4 in. (159 mm) 7 7/8" – 9"
4 1/2 in. Reg.
7 in. (178 mm)
5 1/2 in. Reg.
9" – 9 7/8"
* Clean hole ** All kellys have pin connections on both ends.
High pressure DTH drilling
Up to 8" DTH hammer and max. 8 7/8" bit diameter
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
DML
Technical data
Drilling Method
Rotary or DTH - Multi pass
The Atlas Copco DML is a crawler mounted, hydraulic
tophead drive, multi-pass rotary drilling rig specifically
designed for production blasthole drilling to depths of
175 ft. (53.3 m) with a 30 ft. (9.1 m) drill pipe change. An
optional 35-ft. (10.7 m) steel change is also available to
handle single pass drilling requirements. Various carousel
capacities are also available for the 35-ft. (10.7 m) option.
Hole Diameter
5 7/8 in - 10 5/8 in
149 mm - 270 mm
Hydraulic Pulldown
60,000 lbf
267 kN
Weight on bit
60,000 lb
27,200 kg
Hydraulic Pullback
22,000 lbf
98 kN
Single pass depth
27 ft 5 in or 32 ft 5 in 8.5 m or 10 m
Maximum hole depth*
175 ft or 205 ft
Standard equipment
Feed speed
146 ft/min
0.7 m/s
Rotary head, torque
7,200 Ibfsft
9.76 kNm
Estimated weight
87,000 - 110,000 lb
39.5 - 50 tonnes
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
)NSULATEDCABWITH&/03
#ABPRESSURIZERVENTILATORHEATER
.INEQUARTZHALOGENNIGHTLIGHTINGPACKAGE
$USTHOODWITHCURTAINSANDHYDRAULICALLYRAISINGDUSTmAP
!UXILIARYHOISTFORDRILLPIPEANDACCESSORYHANDLING
(EAVYDUTYENGINESILENCERMUFmER
3EPARATEAIRINTAKElLTERSWITHQUICKRELEASEDUSTDROP
covers for engine and air compressor
'EARINDEXINGCAROUSEL
3LIDINGHYDRAULICFORKWRENCHFORDRILLPIPEBREAKOUT
(YDRAULICALLYPOWEREDAUXILIARYCHAINWRENCH
GALLON,FUELTANK
36TWOMOTORHIGHSPEEDROTARYHEADWITHSPLINE
lubrication, 0 to 160 RPM, and a maximum torque
of 7,200 lbfsft
FOOTDRILLPIPECHANGE
.OBUMPRODCHANGER
%THERINJECTION
*ACKUPINDICATORLIGHTS
4HREEINMMSTROKELEVELINGJACKS
INMMWIDETRIPLEBARGROUSERS
2EINFORCEDRECTANGULARSTEELTRACKFRAMEWITHOSCILLATION
yoke
7ALKWAYSANDRAILINGS
2EMOTETOWERPINNING
"ACKUPALARM
53.3 m or 62.5 m
Dimensions tower up (30 ft tower)
Length
31 ft 10 in
9.7 m
Height
43 ft 8 in
13.3 m
Width
16 ft 6 in
5m
Dimensions tower down (30 ft tower)
Length
43 ft 7 in
13.3 m
Height
17 ft 8 in
5.4 m
Compressor range
Low pressure rotary
1,200 cfm@110 psi / 34.0 m3/[email protected] bar
Low pressure rotary
1,600 cfm@110 psi / 45.0 m3/[email protected] bar
Low pressure rotary
1,900 cfm@110 psi / 53.8 m3/[email protected] bar
High pressure, DTH
(electric motor)
1,050 cfm@350 psi / 29.8 m3/min@24 bar
High pressure, DTH
1,250 cfm@350 psi / 35.4 m3/min@24 bar
High pressure, DTH
1,450 cfm@350 psi / 41 m3/min@24 bar
Engine (2Tier II, 3Tier III )
Caterpillar
C153
540HP / 403 kW@1800RPM (LP 1200)
Cummins
QSX153
530HP / 395 kW@1800RPM (LP 1200)
Caterpillar
C183
630HP / 470 kW@1800RPM (LP 1600)
Cummins
QSX153
600HP / 447 kW@1800RPM (LP 1600)
Caterpillar
C272
800HP / 597 kW@1800RPM (LP 1900)
Cummins
QSK192
755HP / 563 kW@1800RPM (LP 1900)
Caterpillar
C272
800HP / 597 kW@1800RPM (HP 1250)
Cummins
QSK19C2
755HP / 563 kW@1800RPM (HP 1250)
Caterpillar
C272
800HP / 597 kW@2100RPM (HP 1450)
Weg motor
6808
(0K7 n(Z
(LP 1200 or HP1050)
Drill pipe specification 30 ft (9.1 m) or 35 ft (10.7 m)
Drill pipe diameter
Suggested bit
diameters
Thread
4 1/2" (114 mm)
5 7/8" – 6 3/4"
3 1/2" API
5"
(127 mm)
6 3/4" – 7 3/8"
!0)OR"%#/
5 1/2" (140 mm)
6 3/4" – 7 7/8"
"%#/
6 1/4" (159 mm)
7 7/8" – 9"
"%#/
7"
9" – 9 7/8"
"%#/
9 7/8" – 10 5/8"
"%#/
(178 mm)
7 5/8" (194 mm)
High pressure DTH drilling
Up to 8" DTH hammer and max. 8 7/8" bit diameter
-AXIMUMHOLEDEPTHONLYACHIEVEDWITHCERTAINPIPESIZESAND
wall thicknesses
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
Pit Viper PV-235
The Pit Viper series 235 blasthole drills offers several
advanced options, like the RCS control system, remote
tramming, auto levelling, and GPS navigation. The hydraulic system has been refined with load sensing and
other features to reduce horsepower demand. There are
several engine and compressor combinations available
for either rotary or high pressure DTH drilling. The
PV-235 can be supplied with two towers - to drill 35 ft
(10.7 m) or 40 ft (12.2 m) clean holes up to 10 5⁄8"
(270 mm) in diameter.
Standard equipment
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
2#32IG#ONTROL3YSTEMCOMPUTERIZEDNETWORK
3PACIOUSTHERMALINSULATEDCABWITH&/03ANDNOISE
ABATEDLESSTHAND"!
#ABPRESSURIZERVENTILATORHEATER
4WELVEQUARTZHALOGENNIGHTLIGHTINGPACKAGE
Dust hood with curtains and hydraulically raising
DUSTmAP
Auxiliary hoist for drill pipe and accessory handling
(EAVYDUTYENGINESILENCERMUFmER
3EPARATEAIRINTAKElLTERSWITHRUBBERDUSTEVACUATORFOR
engine and air compressors
'EARINDEXINGCAROUSELFORžINPIPE
Sliding hydraulic fork wrench for drill pipe breakout
Hydraulically powered auxiliary breakout wrench
450 gallon fuel tank (1,700 l)
4SV-2-10 two speed spur gear rotary head with spline
lubrication, 0-180 RPM, and a maximum torque
OFLBFsFT
35 ft drill pipe changer
No-bump rod changer
'ROUNDLEVELbattery and starter lockable master-switches
WITHJUMPSTARTRECEPTACLE
*ACKUPINDICATORLIGHTS
&OURINMSTROKELEVELINGJACKS
Triple bar grousers 33.5 in (850 mm) wide
Reinforced rectangular steel track frame with oscillation
yoke
Walkways and railings
Remote tower pinning
"ACKUPALARM
Technical data
Drilling Method
Rotary or DTH - Multi pass
Hole Diameter
6 in - 9 7/8 in
152 mm - 251 mm
Hydraulic Pulldown
60,000 lbf
267 kN
Weight on bit
65,000 lb
29,500 kg
Hydraulic Pullback
27,000 lbf
120 kN
Single pass depth
40, 35 ft
12.2, 10.7 m
Maximum hole depth*
240, 210 ft
73.2, 64.0 m
Feed speed
140 - 193 ft/min
0.7 - 1.0 m/s
Rotary head, torque
4,900 Ibfsft
8,800 Ibfsft
6.6 kNm
11.9 kNm
Estimated weight
128,000 lb
58 tonnes
Dimensions tower up (40 ft tower)
Length
34 ft 2 in
10.4 m
Height
42 ft 6 in
19 m
Width
17 ft 4 in
5.3 m
Dimensions tower down (40 ft tower)
Length
63 ft 5 in
19.3 m
Height
20 ft 4 in
6.4 m
Compressor range
Low pressure rotary
1,600 cfm@110 psi / 45.0 m3/[email protected] bar
Low pressure rotary
1,900 cfm@110 psi / 53.8 m3/[email protected] bar
High pressure, DTH
1,250 cfm@350 psi / 35.4 m3/min@24 bar
High pressure, DTH
1,450 cfm@350 psi / 41.0 m3/min@24 bar
High pressure, DTH
(electric motor)
1,250 cfm@350 psi / 35.4 m3/min@24 bar
High pressure, DTH
1,300 cfm@435 psi / 37.6 m3/min@30 bar
Engine (3Tier III, 2Tier II)
Caterpillar
C183
630HP / 470 kW@1800RPM (LP 1600)
Cummins
QSX153
600HP / 447 kW@1800RPM (LP 1600)
Caterpillar
C272
800HP / 597 kW@1800RPM
(LP 1900 or HP 1250)
Cummins
QSK192
755HP / 563 kW@1800RPM (LP 1900 or HP
1250)
2
Caterpillar
C27
WEG
6808
800HP / 597 kW@2100RPM (HP 1450)
(0K7
(Z
Drill pipe specification: 35 ft (10.7 m) or 40 ft (12.2 m)
Drill pipe diameter
Suggested bit
diameters
Thread
4 1/2" (114 mm)
6" – 6 3/4"
"%#/
5" (127 mm)
6 3/4" - 7 3/8"
"%#/
5 1/2" (140 mm)
6 3/4" - 7 7/8"
"%#/
6 1/4" (159 mm)
7 7/8" - 9"
"%#/
7" (178 mm)
9"
"%#/
7 5/8" (194 mm)
9 7/8"
"%#/
8" (203 mm)
9 7/8" - 10 5/8"
"%#/
High pressure DTH drilling
Up to 8" DTH hammer and max. 8 7/8" bit diameter
PV-235
-AXIMUMHOLEDEPTHONLYACHIEVEDWITHCERTAINPIPESIZESAND
wall thicknesses
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
Pit Viper PV-271
Technical data
The PV-271 is designed to handle 6-¼" up to 8-5⁄8 " drill
rods. The cable feed system utilizes a dual rod/dual
piston cylinder and offers high feed speeds for increased
productivity. The PV-271 offers a 55 ft single-pass tower
with a total depth capacity of 105 ft through a 2-rod
carousel with 25 ft rods. It has an option to be delivered
with the RCS Computerized rig control system and a
new fully integrated cabin, incorporating functions like;
remote tramming, auto levelling, auto drilling, and GPS
navigation.
Standard equipment
s )NSULATEDPRESSURIZEDAIRCONDITIONEDCABWITHTINTED
glass and suspension operator seat
s #ATERPILLAR8,UNDERCARRIAGEWITHHYDRAULICTRACK
tensioners
s (YDRAULICCYLINDERSDRIVENCABLEFEEDSYSTEM
s (YDRAULICMOTORDRIVENROTARYHEADWITHSPLINELUBRICATION
maximum 8,700 lbfsft torque; speed range 0 - 150 rpm
s 2OTARYHEADTACHOMETERONOPERATORCONSOLE
s 2EMOTEHYDRAULICTOWERPINNING
s 4WORODCAROUSELFOR—TO 5⁄8" drill rods
s .OBUMPRODCHANGER
s (YDRAULICALLYPOWEREDBREAKOUTWRENCHFORKCHUCK
s (ANDS&REEAUXILIARYHYDRAULICCHAINWRENCH
s LBKGCAPACITYAUXILIARYHOIST
s (YDRAULICALLYRETRACTABLEDUSTCURTAINS
s #OOLINGPACKAGE
s 3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
s 7IDEmANGESTRUCTURALSTEELBEAMFRAMEWITHOSCILLATION
yoke mounting
s (YDRAULIC4EST3TATION
s LIGHTNIGHTLIGHTINGPACKAGEWATTHALOGEN
s &ULLDECKSERVICECATWALKSANDRAILINGS
s 4WO MANDONEMSTROKELEVELINGJACKS
Drilling Method
Rotary or DTH – Single pass
Hole Diameter
6 3/4 in - 10 5/8 in
171 mm - 270 mm
Hydraulic Pulldown
70,000 lbf
311 kN
Weight on bit
75,000 lb
34,000 kg
Hydraulic Pullback
35,000 lbf
156 kN
Single pass depth
55 ft*
16.8 m*
Maximum hole depth
105 ft
32 m
Feed speed
127 ft/min
0.6 m/s
Rotary head, torque
8,700 Ibfsft
11.8 kNm
Estimated weight
185,000 lb
84 tonnes
Length
41 ft 3 in
12.6 m
Height
87 ft
26.5 m
Width
18 ft 4 in
5.6 m
Dimensions tower up
Dimensions tower down
Length
83 ft 7 in
25.5 m
Height
22 ft 1 in
6.7 m
Compressor range
Low pressure rotary
1,900 cfm@110 psi / 53.8 m3/[email protected] bar
Low pressure rotary
2,600 cfm@110 psi / 73.6 m3/[email protected] bar
High pressure, DTH
1,450 cfm@350 psi / 41.1 m3/min@24 bar
Engine (Tier ll)
Caterpillar
C27
800HP / 597 kW@1800RPM (LP 1900)
Cummins
QSK19
755HP / 563 kW@1800RPM (LP 1900)
Caterpillar
C32
950HP / 708 kW@1800RPM (LP 2600)
Caterpillar
C27
800HP / 597 kW@2100RPM (HP 1450)
Weg motor
6808
(0K7
OR(Z
Weg motor
6811
(0K7
OR(Z
Drill pipe specification: 25 ft (7.6 m)
Drill pipe diameter
6 1/4"
7"
7 5/8"
8"
(159 mm)
(178 mm)
(194 mm)
(203 mm)
8 5/8"
(219 mm)
Suggested bit
diameters
Thread
6 3/4" – 9"
"%#/
9" – 9 7/8"
"%#/
9 7/8" – 10 5/8"
"%#/
9 7/8" – 10 5/8"
"%#/
10 5/8"
"%#/
High pressure DTH drilling
Up to 8" DTH hammer and max. 9 7/8" bit diameter
* There is also a 65 ft (19.8 m) clean hole tower option
(see page 76 - 77)
PV-271
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
Pit Viper 271 RCS
The PV-271 Rig Control System (RCS) is designed to
handle 6-¼" to 8-5⁄8" drill rods. The cable feed system
utilizes a dual rod/dual piston cylinder and offers high
feed speeds for increased productivity. The PV-271 RCS
offers a 55 ft single-pass tower with a total depth capacity of 105 ft through a 2-rod carousel with 25 ft rods.
This version of the machine comes standard with a new
cab that fully integrates the RCS with the option to fully
incorporate the following functions: wireless remote
tramming, auto leveling, auto drilling, and
GPS navigation.
Standard equipment
s 3PACIOUSTHERMALINSULATEDCABWITH&/03ANDNOISE
ABATEMENTTOLESSTHAND"!
s %XCAVATORSTYLECHAIRANDCONTROLSFORINCREASEDCOMFORT
and visibility
s 3TANDARD#ABPRESSURIZERVENTILATORHEATERWITHTHEOPTION
TOUPGRADETHEPRESSURIZER
s #ATERPILLAR8,UNDERCARRIAGEWITHHYDRAULICTRACK
tensioners
s (YDRAULICCYLINDERSDRIVENCABLEFEEDSYSTEM
s Hydraulic motor driven rotary head with spline lubrication,
maximum 8,700 lbf-ft torque; speed range 0 – 150 rpm
s 2OTARY(EADTACHOMETERINTEGRATEDINTOTHE2#3SYSTEM
s 2EMOTEHYDRAULICTOWERPINNING
s 4WORODCAROUSELFOR—TO5⁄8" drill rods
s h.O"UMPvRODCHANGER
s (YDRAULICALLYPOWEREDBREAKOUTWRENCHFORKCHUCK
s (ANDSFREEAUXILIARYHYDRAULICCHAINWRENCH
s LBKGCAPACITYAUXILIARYHOIST
s (YDRAULICALLYRETRACTABLEDUSTCURTAINS
s #OOLINGPACKAGE
s 3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
s 7IDEmANGESTRUCTURALSTEELBEAMFRAMEWITHOSCILLATION
yoke mounting
s LIGHTNIGHTLIGHTINGPACKAGEnWATTHALOGEN
s &ULLDECKSERVICECATWALKSANDRAILINGS
s 4WOMANDONEMSTROKELEVELINGJACKS
s 53GALLON,FUELTANKWOPTIONTOUPGRADETO
larger tanks.
Technical data
Drilling Method
Rotary or DTH – Single pass
Hole Diameter
6 3/4 in - 10 5/8 in
171 mm - 270 mm
Hydraulic Pulldown
70,000 lbf
311 kN
Weight on bit
75,000 lb
34,000 kg
Hydraulic Pullback
35,000 lbf
156 kN
Single pass depth
55 ft*
16.8 m*
Maximum hole depth
105 ft
32 m
Feed speed
127 ft/min
0.6 m/s
Rotary head, torque
8,700 Ibfsft
11.8 kNm
Estimated weight
185,000 lb
84 tonnes
Dimensions tower up
Length
54 ft
16.4 m
Height
87 ft
26.5 m
Width
23 ft 8 in
7.2 m
Dimensions tower down
Length
86 ft 4 in
26.3 m
Height
23 ft 3 in
7.0 m
Compressor range
Low pressure rotary
1,900 cfm@110 psi / 53.8 m3/[email protected] bar
Low pressure rotary
2,600 cfm@110 psi / 73.6 m3/[email protected] bar
High pressure, DTH
1,450 cfm@350 psi / 41.1 m3/min@24 bar
Engine (Tier ll)
Caterpillar
C27
800HP / 597 kW@1800RPM (LP 1900)
Cummins
QSK19
755HP / 563 kW@1800RPM (LP 1900)
Caterpillar
C32
950HP / 708 kW@1800RPM (LP 2600)
Caterpillar
C27
800HP / 597 kW@2100RPM (HP 1450)
Weg motor
6808
(0K7
OR(Z
Weg motor
6811
(0K7
OR(Z
Drill pipe specification: 25 ft (7.6 m)
Drill pipe diameter
Suggested bit
diameters
Thread
6 1/4"
6 3/4" – 9"
"%#/
7" (178 mm)
9" – 9 7/8"
"%#/
7 5/8"
9 7/8" – 10 5/8"
"%#/
8" (203 mm)
9 7/8" – 10 5/8"
"%#/
8 5/8"
10 5/8"
"%#/
(159 mm)
(194 mm)
(219 mm)
High pressure DTH drilling
Up to 8" DTH hammer and max. 9 7/8" bit diameter
* There is also a 65 ft (19.8 m) clean hole tower option
(see page 76 - 77)
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
Pit Viper PV-275
The PV-275 is designed to handle 6-¼" up to 8-5⁄8 " drill
rods. The cable feed system utilizes a dual rod/dual
piston cylinder and offers high feed speeds for increased
productivity. The PV-275 offers a multi-pass tower with
195-ft depth capacity through a 4-rod carousel with
40-ft rods. It has an option to be delivered with the
RCS Computerized rig control system and a new fully
integrated cabin, incorporating functions like; remote
tramming, auto levelling, auto drilling, and GPS
navigation.
Standard equipment
s )NSULATEDPRESSURIZEDAIRCONDITIONEDCABWITHTINTED
glass and suspension operator seat
s #ATERPILLAR3,UNDERCARRIAGEWITHHYDRAULICTRACK
tensioners
s (YDRAULICCYLINDERSDRIVENCABLEFEEDSYSTEM
s (YDRAULICMOTORDRIVENROTARYHEADWITHSPLINE
lubrication, maximum 8,700 lbfsft (11,800 Nm) torque;
speed range 0 – 150 rpm
s 2OTARYHEADTACHOMETERONOPERATORCONSOLE
s 2EMOTEHYDRAULICTOWERPINNING
s &OURRODCAROUSELFOR—TO5⁄8" drill rods
s .OBUMPRODCHANGER
s (YDRAULICALLYPOWEREDBREAKOUTWRENCHFORKCHUCK
s (ANDS&REEAUXILIARYHYDRAULICWRENCH
s LBKGCAPACITYAUXILIARYHOIST
s (YDRAULICALLYRETRACTABLEDUSTCURTAINS
s (YDRAULIC4EST3TATION
s 4WOMANDONEMSTROKELEVELINGJACKS
s #OOLINGPACKAGE
s 53GALLON,FUELTANKWOPTIONTOUPGRADETO
larger tanks
s 3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
s 7IDEmANGESTRUCTURALSTEELBEAMFRAMEWITHOSCILLATION
yoke mounting
s LIGHTNIGHTLIGHTINGPACKAGEWATTHALOGEN
s &ULLDECKSERVICECATWALKSANDRAILINGS
Technical data
Drilling Method
Rotary or DTH – Multi pass
Hole Diameter
6 3/4 in - 10 5/8 in
171 mm - 270 mm
Hydraulic Pulldown
70,000 lbf
311 kN
Weight on bit
75,000 lb
34,000 kg
Hydraulic Pullback
35,000 lbf
156 kN
Single pass depth
37 ft
11.3 m
Maximum hole depth
195 ft
59.4 m
Feed speed
127 ft/min
0.6 m/s
Rotary head, torque
8,700 Ibfsft
11.8 kNm
Estimated weight
185,000 lb
84 tonnes
Dimensions tower up
Length
41 ft 6 in
12.6 m
Height
67 ft
20.4 m
Width
18 ft 4 in
5.6 m
Dimensions tower down
Length
63 ft 6 in
19.4 m
Height
22 ft 1 in
6.7 m
Compressor range
Low pressure rotary
1,900 cfm@110 psi / 53.8 m3/[email protected] bar
Low pressure rotary
2,600 cfm@110 psi / 73.6 m3/[email protected] bar
High pressure, DTH
1,450 cfm@350 psi / 41.1 m3/min@24 bar
Engine (Tier ll)
Caterpillar
C27
800HP / 597 kW@1800RPM (LP 1900)
Cummins
QSK19
755HP / 563 kW@1800RPM (LP 1900)
Caterpillar
C32
950HP / 708 kW@1800RPM (LP 2600)
Caterpillar
C27
800HP / 597 kW@2100RPM (HP 1450)
Weg motor
6808
(0K7
OR(Z
Weg motor
6811
(0K7
OR(Z
Drill pipe specification: 40 ft (12.2 m)
Drill pipe diameter
Suggested bit
diameters
Thread
6 1/4" (159 mm)
6 3/4" – 9"
"%#/
7"
9" – 9 7/8"
"%#/
7 5/8" (194 mm)
9 7/8" – 10 5/8"
"%#/
8"
9 7/8" – 11"
"%#/
10 5/8"
"%#/
(178 mm)
(203 mm)
8 5/8" (219 mm)
High pressure DTH drilling
Up to 8" DTH hammer and max. 9 7/8" bit diameter
PV-275
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
Pit Viper 275 RCS
The PV-275 Rig Control System (RCS) is designed to
handle 6-¼" up to 8-5⁄8"drill rods. The cable feed system
utilizes a dual rod/dual piston cylinder and offers high
feed speeds for increased productivity. The PV-275 RCS
offers a multi-pass tower with a total depth capacity
of 195 ft through a 4-rod carousel with 40 ft rods. This
version of the machine comes standard with a new
cab that fully integrates the RCS with the option to
fully incorporate the following functions: wireless
remote tramming, auto leveling, auto drilling, and
GPS navigation.
Standard equipment
s 3PACIOUSTHERMALINSULATEDCABWITH&/03ANDNOISE
ABATEMENTTOLESSTHAND"!
s %XCAVATORSTYLECHAIRANDCONTROLSFORINCREASEDCOMFORT
and visibility
s 3TANDARD#ABPRESSURIZERVENTILATORHEATERWITHTHEOPTION
TOUPGRADETHEPRESSURIZER
s #ATERPILLAR3,UNDERCARRIAGEWITHHYDRAULICTRACK
tensioners
s (YDRAULICCYLINDERSDRIVENCABLEFEEDSYSTEM
s (YDRAULICMOTORDRIVENROTARYHEADWITHSPLINELUBRICATION
maximum 8,700 lbf-ft torque; speed range 0 – 150 rpm
s 2OTARY(EADTACHOMETERINTEGRATEDINTOTHE2#3SYSTEM
s 2EMOTEHYDRAULICTOWERPINNING
s &OURRODCAROUSELFOR—TO5⁄8" drill rods
s h.O"UMPvRODCHANGER
s (YDRAULICALLYPOWEREDBREAKOUTWRENCHFORKCHUCK
s (ANDSFREEAUXILIARYHYDRAULICCHAINWRENCH
s LBKGCAPACITYAUXILIARYHOIST
s (YDRAULICALLYRETRACTABLEDUSTCURTAINS
s #OOLINGPACKAGE
s 3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
s 7IDEmANGESTRUCTURALSTEELBEAMFRAMEWITHOSCILLATION
yoke mounting
s LIGHTNIGHTLIGHTINGPACKAGEnWATTHALOGEN
s &ULLDECKSERVICECATWALKSANDRAILINGS
s 4WOMANDONEMSTROKELEVELINGJACKS
s 53GALLON,FUELTANK
Technical data
Drilling Method
Rotary or DTH – Multi pass
Hole Diameter
6 3/4 in - 10 5/8 in
171 mm - 270 mm
Hydraulic Pulldown
70,000 lbf
311 kN
Weight on bit
75,000 lb
34,000 kg
Hydraulic Pullback
35,000 lbf
156 kN
Single pass depth
37 ft
11.3 m
Maximum hole depth
195 ft
59.4 m
Feed speed
127 ft/min
0.6 m/s
Rotary head, torque
8,700 Ibfsft
11.8 kNm
Estimated weight
185,000 lb
84 tonnes
Dimensions tower up
Length
54 ft
16.4 m
Height
67 ft
20.4 m
Width
23 ft 3 in
7.0 m
Dimensions tower down
Length
67 ft 7 in
20.6 m
Height
23 ft 3 in
7.0 m
Compressor range
Low pressure rotary
1,900 cfm@110 psi / 53.8 m3/[email protected] bar
Low pressure rotary
2,600 cfm@110 psi / 73.6 m3/[email protected] bar
High pressure, DTH
1,450 cfm@350 psi / 41.1 m3/min@24 bar
Engine (Tier ll)
Caterpillar
C27
800HP / 597 kW@1800RPM (LP 1900)
Cummins
QSK19
755HP / 563 kW@1800RPM (LP 1900)
Caterpillar
C32
950HP / 708 kW@1800RPM (LP 2600)
Caterpillar
C27
800HP / 597 kW@2100RPM (HP 1450)
Weg motor
6808
(0K7
OR(Z
Weg motor
6811
(0K7
OR(Z
Drill pipe specification: 40 ft (12.2 m)
Drill pipe diameter
Suggested bit
diameters
Thread
6 1/4" (159 mm)
6 3/4" – 9"
"%#/
7"
9" – 9 7/8"
"%#/
7 5/8" (194 mm)
9 7/8" – 10 5/8"
"%#/
8"
9 7/8" – 11"
"%#/
10 5/8"
"%#/
(178 mm)
(203 mm)
8 5/8" (219 mm)
High pressure DTH drilling
Up to 8" DTH hammer and max. 9 7/8" bit diameter
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
DM-M3
Technical data
The Atlas Copco DM-M3 is a crawler-mounted, hydraulic
tophead drive, multi-pass rotary drilling rig specifically
designed for the blasthole drilling of 9-7⁄8 in. (251 mm)
to 12-¼ in. (311 mm) diameter holes. The on-board depth
capability is up to 240 feet (73 m) when using 8-5⁄8 in.
diameter (219 mm) drill pipe and a 5-rod carousel.
Standard drill pipe length is 40 feet (12.2 m). Hydraulic
pulldown is featuring a patented hydrostatic, closedloop system acting through twin, double-rod hydraulic
cylinders and cable.
Standard equipment
s )NSULATEDPRESSURIZED&/03CABWITHHEATER
s 2OTARYSCREW#&- PSIAIR
compressor
s #ATERPILLAR#DIESELENGINE(0ATRPM
s LIGHTWATTQUARTZHALOGENNIGHTLIGHTINGSYSTEM
s #ABANDLADDERACCESSLIGHTSPLUSDUSTCURTAINLIGHT
s #OOLINGPACKAGE
s 2EMOTEHYDRAULICTOWERPINNING
s !UXILIARYHOISTOFLBKGCAPACITYWITHLIFTINGBAIL
s (YDRAULICALLYACTUATEDDRILLPIPECAROUSELINTERNALTOTOWER
for 4 drill pipe or 5 for 8- 5/8 in. diameter 40 ft.
s (YDRAULICSLIDINGFORKCHUCKBREAKOUTWITHAUXILIARY
hydraulic wrench
s 53GALLON,FUELCAPACITY
s 7IDEmANGESTRUCTURALSTEEL)BEAMMAINFRAMEWITH
oscillation yoke mounting
s 3EPARATETHREESTAGEAIRINTAKElLTERSFORENGINEAND
compressor
s 2OTARYHEADTACHOMETER
s 4HREEHYDRAULICLEVELINGJACKSANDJACKSUPINDICATORINCAB
s (YDRAULICALLYACTUATEDRODSUPPORTARMTOALIGNDRILLPIPE
during rod changing operations and when using the angle
drill option
s &ULLWALKWAYSANDRAILINGS
s INMMWIDETRIPLEBARREPLACEBLEGROUSERPADS
s 2OTARYHEADWITHSPLINELUBRICATION
Drilling Method
Rotary - Multi pass
Hole Diameter
9 7/8 in - 12 1/4 in
251 mm - 311 mm
Hydraulic Pulldown
90,000 lbf
400 kN
Weight on bit
90,000 lb
40,800 kg
Hydraulic Pullback
41,500 lbf
185 kN
Single pass depth
37 ft
11.3 m
Maximum hole depth*
200 - 240 ft
61 - 73.2 m
Feed speed
144 ft/min
0.7 m/s
Rotary head, torque
10,183 Ibfsft
13.8 kNm
Estimated weight
230,000 lb
104 tonnes
Dimensions tower up
Length
40 ft 5 in
12.3 m
Height
67 ft
20.4 m
Width
18 ft 11 in
5.8 m
Dimensions tower down
Length
66 ft 6 in
20.3 m
Height
23 ft 9 in
7.2 m
Compressor range
Low pressure rotary
CFM
PSIM¨MIN
"AR
Engine (Tier ll)
Caterpillar
C32
950HP / 709 kW@1800RPM (LP 2600)
Cummins
QST30
950HP / 709 kW@1800RPM (LP 2600)
Weg motor
6811
(0K7 OR(Z,0
Drill pipe specification: 40 ft (12.2 m)
Drill pipe diameter
Suggested bit
diameters
Thread
7 5/8" (194 mm)
9 7/8" – 10 5/8"
"%#/
8 5/8" (219 mm)
10 5/8" - 11"
"%#/
9 1/4" (235 mm)
11" – 12 1/4"
"%#/
10 3/4" (273 mm)
12 1/4"
"%#/
-AXIMUMHOLEDEPTHONLYACHIEVEDWITHCERTAINPIPESIZESAND
wall thicknesses.
DM-M3
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
Pit Viper 311
The Pit Viper 311 is a crawler-mounted, hydraulic
tophead drive, single-pass rotary drilling rig specifically
designed for the blasthole drilling of 9 in.(228 mm) to
12 1/4 in (311 mm) diameter holes. It has a single-pass
depth capability of 65’ (20 m) with total depth capability
of 135’ (41 m). Its hydraulic driven cable feed system is
capable of 110,000 lbf. (490 kN) of bit loading. Due to
the light weight of the cable feed system the PV-311
can operate with a “live tower”. A patented automatic
tensioning system eliminates down time for cable
adjustments. It has several advanced options like an
auto drilling system, auto levelling, remote tramming,
and GPS navigation.
Standard equipment
s 2#3RIGCONTROLSYSTEMCOMPUTERIZEDNETWORK
s .EWLARGEINSULATEDCABINWITHINTEGRATED!#LARGE
electrical cabinets housing computers, and a training seat.
s 3000 CFM (84.9 m3/min) @ 110 psig (7.6 bar) air compressor
s!TLAS#OPCOCLASSUNDERCARRIAGEWITHTWOSPEED
hydraulic propel and automatic track tensioning.
Optional: Caterpillar 350 Custom undercarriage with hydraulic
propel and automatic hydraulic track tensioning
s&UELSAVINGAUTOMATICHYDRAULICCLUTCH
s $UAL(YDRAULICCYLINDERDRIVENCABLEFEEDSYSTEM
s $UAL(YDRAULICMOTORDRIVENROTARYHEADWITHSPLINE
lubrication
s4WORODCAROUSELFOR5⁄8" to 10 ¾" diameter x 35' drill pipe
s h.OBUMPvRODCHANGER
s (YDRAULICALLYPOWEREDBREAKOUTWRENCHFORKCHUCK
s (ANDS&REEAUXILIARYHYDRAULICWRENCH
s LBKGCAPACITYAUXILIARYHOIST
s (YDRAULICALLYRETRACTABLEDUSTCURTAINS
s &OURINCHMSTROKELEVELINGJACKS
s #OOLINGPACKAGE
s 53GALLONLITERFUELTANK
s 3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
s 7IDEmANGESTRUCTURALSTEEL)BEAMFRAMEWITHOSCILLATION
yoke mounting
s &ULLDECKSERVICECATWALKSANDRAILINGS
s !UTOMATICLUBRICATIONSYSTEM
s .ORDIC.IGHTLIGHTPACKAGE
s !TTENTIONHORNPROPELALARM
s 'ROUNDLEVELSHUTDOWNS
s $ECKINGINTOWERWHENHORIZONTALABOVERODCHANGER
s INMMWIDETRIPLEBARREPLACEBLEGROUSERPADS
Technical data
Drilling Method
Rotary or DTH - single pass
Hole Diameter
9 in - 12 1/4 in
228 - 311 mm
Hydraulic Pulldown
100,000 lbf
445 kN
Weight on bit
110,000 lb
49,895 kg
Hydraulic Pullback
50,000 lbf
220 kN
Single pass depth
65 ft
19.8 m
Maximum hole depth*
135 ft
45 m
Rotary head, torque
12,900 Ibfsft
13.8 kNm
Estimated weight
310,000 lb
140 tonnes
Length
48 ft
14.6 m
Height
100 ft 6 in
30.6 m
Width
25 ft 4 in
7.7 m
Dimensions tower up
Dimensions tower down
Length
99 ft
30.2 m
Height
29 ft
8.8 m
Compressor range
Low pressure rotary
3000 CFM@100 psi / 84.9 m3/[email protected] bar
3800 CFM @100 psi / 107.6 m3/[email protected] bar
Engine (Tier ll)
Caterpillar
C32
1125 HP / 839 kW@1800RPM
Cummins
QSK 38
1260 HP / 940 kW @1800RPM
Caterpillar
3512
1500 HP / 1118 kW@1800RPM
MTU
16V2000
1205 HP / 899 kW@1800RPM
Engine (Tier IV)
Caterpillar
C32
1125 HP / 839 kW
MTU
16V2000
1300 HP / 969 kW
Drill pipe specification: 35 ft (10.7 m)
Drill pipe diameter
Suggested bit
diameters
Thread
7 5/8" (194 mm)
9" - 9 7/8"
"%#/
8"
9 7/8" - 10 5/8"
—"%#/
8 5/8" (219 mm)
10 5/8"
"%#/
9 1/4" (235 mm)
12 1/4"
"%#/
10 3/4" (273 mm)
12 1/4"
"%#/
(203 mm)
-AXIMUMHOLEDEPTHONLYACHIEVEDWITHCERTAINPIPESIZESAND
wall thicknesses.
Visit www.atlascopco.com/blastholedrills for more information
BLASTHOLE DRILLS
BLASTHOLE DRILLS
Pit Viper PV-351
The Pit Viper 351 is a crawler-mounted, hydraulic
tophead drive, single-pass rotary drilling rig specifically
designed for the blasthole drilling of 10-5⁄8 " to 16 in
diameter holes. It has a single-pass depth capability of
65’ (20 m) with total depth capability of 135’ (41 m). Its
hydraulic driven cable feed system is capable of 125,000
lbf. (511 kN) of bit loading. Due to the light weight of
the cable feed system the PV-351 can operate with a
“live tower”. A patented automatic tensioning system
is eliminating down time for cable adjustments. It has
several advanced options like an auto drilling system,
auto levelling, remote tramming, and GPS navigation.
Standard equipment
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
2#3RIGCONTROLSYSTEMCOMPUTERIZEDNETWORK
)NSULATEDAIRCONDITIONEDCAB
#&-M3/min) @ 110 psig (7.6 bar) air compressor
#ATERPILLAR#USTOMUNDERCARRIAGEWITHHYDRAULIC
propel and automatic hydraulic track tensioning
(YDRAULICCYLINDERDRIVENCABLEFEEDSYSTEM
(YDRAULICMOTORDRIVENROTARYHEADWITHSPLINELUBRICATION
4WORODCAROUSELFOR5/8" to 13-3/8" diameter x 35’ drill pipe
h.OBUMPvRODCHANGER
(YDRAULICALLYPOWEREDBREAKOUTWRENCHFORKCHUCK
(ANDS&REEAUXILIARYHYDRAULICWRENCH
LBKGCAPACITYAUXILIARYHOIST
(YDRAULICALLYRETRACTABLEDUSTCURTAINS
&OURINCHMSTROKELEVELINGJACKS
#OOLINGPACKAGE
53GALLON,FUELTANK
3EPARATEAIRINTAKElLTERSFORENGINEANDAIRCOMPRESSOR
7IDEmANGESTRUCTURALSTEEL)BEAMFRAMEWITHOSCILLATION
yoke mounting
&ULLDECKSERVICECATWALKSANDRAILINGS
!UTOMATICLUBRICATIONSYSTEM
.ORDIC.IGHTLIGHTPACKAGE
!TTENTIONHORNPROPELALARM
'ROUNDLEVELSHUTDOWNS
$ECKINGINTOWERWHENHORIZONTALABOVERODCHANGER
Technical data
Drilling Method
Rotary - Single pass
Hole Diameter
10 5/8 in - 16 in
270 mm - 406 mm
Hydraulic Pulldown
120,000 lbf
534 kN
Weight on bit
125,000 Ib
56,700 kg
Hydraulic Pullback
60,000 lbf
267 kN
Single pass depth
65 ft
19.8 m
Maximum hole depth
135 ft
41.1 m
Feed speed
127 - 158 ft/min
0.6 - 0.8 m/s
Rotary head, torque
19,000 Ibfsft
25.7 kNm
Estimated weight
385,000 lb 415,000 lb
175 tonnes 188 tonnes
Length
53 ft 10 in
16.4 m
Height
103 ft 9 in
31.6 m
Width
26 ft 8 1/2 in
8.1 m
Dimensions tower up
Dimensions tower down
Length
98 ft
29.9 m
Height
27 ft 11 in
8.5 m
Compressor range
Low pressure rotary
3,000 cfm@110psi / 84.9m3/[email protected] bar
Low pressure rotary
(electric motor)
3,200 cfm@110psi / 90.6m3/[email protected] bar
Low pressure rotary
3,800 cfm@110psi / 107.6m3/[email protected] bar
Engine (Tier l)
Caterpillar
3512
Cummins
QSK45
1500HP / 1119 kW@1800RPM (LP 3000)
Weg motor
6811
(0K7
1650HP / 1230 kW@1800RPM (LP 3800)
OR(Z(LP 3200)
Drill pipe specification: 35 ft (10.7 m)
Drill pipe diameter
Suggested bit
diameters
Thread
8 5/8" (219 mm)
10 5/8" - 11"
"%#/
9 1/4" (235 mm)
11" – 12 1/4"
"%#/
10 3/4" (273 mm)
12 1/4" - 13"
"%#/
12 3/4"
(324 mm)
15" – 16"
"%#/
13 3/8"
(340 mm)
16"
"%#/
Visit www.atlascopco.com/blastholedrills for more information