Brise Soleil INDEX(02-07-10)

System 22 Brise Soleil
INDEX
Section 0:
Specification, Profile Index, and Component ID
Section 1:
Section Drawings
Section 2:
General Arrangement Drawings
Section 3:
Ironmongery Requirements
Section 4:
Fabrication Details
Section 5:
Installation and Assembly
Section 6:
Structural Guidance
Issue Date: 02/07/10
Specification
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
The Metal Technology Aluminium Brise Soleil System offers a range of Brise Soleil
that can be used on its own or integrated within the Metal Technology Curtain
Walling Systems.
Introduction
Materials
Installation
The system is designed to accommodate
either vertical or horizontal applications.
The basic suite has 150mm and 200mm
blades to allow the Brise Soleil to suit
most architectural requirements. They
can be fitted either directly onto the
structure or onto Metal Technology 28mm
System 17 curtain walling. The system
offers a choice of 150mm or 200mm
blades.
The aluminium profiles are extruded from
aluminum alloy 6060T6, T5 or T4
complying with the recommendations of
BS EN 12020-2 / BS EN 755-Parts 1 to 9.
Detailed installation instructions are
provided which should be strictly followed.
Finishes
For the cantilevered Brise Soleil system,
loading graphs are provided in this manual,
which should be strictly followed.
Various other profiles can be designed
and incorporated allowing architects to
achieve flexible designs.
As with all Metal Technology Systems,
the Aluminium Brise Soleil System is
manufactured to exacting standards
enabling economy to be combined with
strength to give many years of trouble
free operation.
Scope
This specification defines materials,
construction, finishes and size limits for
the Aluminium Brise Soleil System.
Size Limits
The range of sections can be provided in
either of the following ranges of finishes:
1. Anodised to BS 1615 or BS 3987
2. Powder organic coated to BS 6496 or BS
EN 12206-1
Construction
The Brise Soleil blade is square cut and
fixed securely to the outriggers/upriggers
with stainless steel screws.
Brackets are pre-fixed to the curtain
walling or building structure before the
Brise Soleil arrays are hooked onto
pre-positioned pins on the fixing brackets.
The Brise Soleil is then securely bolted into
position.
For the propped and vertical Brise Soleil,
the main limit on the design will be the
blade length. Graphs are provided for the
design of these which should be followed.
Development
Our policy is to continually research
the market for new and improved products.
We must therefore retain the right to
amend specifications without prior notice.
It is recognised at Metal Technology that in
some instances special sections may be
required for particular projects. When this
occurs it may be possible to produce
bespoke sections subject to there being
sufficient quantity and adequate time.
Standard fixing brackets make the
application of Brise Soleil a simple and
trouble free operation.
SHEET
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
rev 3
22 / 0 / 10
03/12/10
Profile Index
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
Section Properties
Profile illustration
SHEET REF COMPUTER PERIMETER
NUMBER REF NUMBER
mm
ILLUSTRATION
DIMENSIONS
BS15
22/1/10
BS05
313
22/1/10
BS06
414
22/1/10
BS15
220
22/1/10
BS16
290
BS16
BS05
BS06
Not to Scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 1
22 / 0 / 20
19/11/09
Component Identification
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
BS77
GRUB SCREW
BS50
BLADE FIXING SCREW
BS80
BRACKET PIN
BS60
OUTRIGGER PACKER
BS128
LOWER PROP
OUTRIGGER
BRACKET
BS85
THREADED ADJUSTMENT
BAR FOR BRISE SOLEIL
PROP
HR5064
45mm FOIL-BACKED
SEALANT TAPE
7201
STITCH PLATE SCREW
BS45
PROP FIXING BOLT
BS47
BRACKET FIXING BOLT
BS48
NYLOC NUT
UPPER PROP
BS112
LOWER PROP
196mm LONG
Not to Scale
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
MT
REFERENCE
UPPER PROP
LENGTH (mm)
DESCRIPTION
BS114
UPPER PROP FOR BS94
842
BS115
UPPER PROP FOR BS95
1082
BS116
UPPER PROP FOR BS96
1323
BS117
UPPER PROP FOR BS97
1563
BS118
UPPER PROP FOR BS98
1803.5
BS133
UPPER PROP FOR BS103
739
BS134
UPPER PROP FOR BS104
1021.5
BS135
UPPER PROP FOR BS105
1304.5
BS136
UPPER PROP FOR BS106
1587
BS137
UPPER PROP FOR BS107
1870
SHEET
rev 4
22 / 0 / 30
04/08/11
Component Identification
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
12
4
12
4
12
4
BS57
HORIZONTAL UPPER
PROP CURTAIN
WALLING BRACKET
BS69
VERTICAL BRISE
SOLEIL CURTAIN
WALLING BRACKET
BS70
150mm HORIZONTAL
BRISE SOLEIL CURTAIN
WALLING BRACKET
127
100
427
400
100
300
150
89
BS71
200mm HORIZONTAL
BRISE SOLEIL CURTAIN
WALLING BRACKET
500
BS53
HORIZONTAL BRISE SOLEIL STITCH PLATE
400
BS51
VERTICAL BRISE SOLEIL STITCH PLATE
210
BS52
HORIZONTAL UPPER PROP STITCH PLATE
Not to Scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 5
22 / 0 / 40
19/07/11
Component Identification
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
BS87
150mm BRISE SOLEIL "T" BRACKET
177
200
150
3
12
3
12
BS88
200mm BRISE SOLEIL "T" BRACKET
100
150
13
5
75
JIG22002
JIG FOR MULLION PREPS
Not to Scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
BS89
UPPER PROP "T" BRACKET
SHEET
rev 4
22 / 0 / 50
27/06/11
227
13
5
75
13
5
75
Component Identification
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
BS92
150mm 2-BLADE OUTRIGGER
BS93
150mm 3-BLADE OUTRIGGER
506
676
BS94
150mm 4-BLADE OUTRIGGER
846
BS95
150mm 5-BLADE OUTRIGGER
1016
BS96
150mm 6-BLADE OUTRIGGER
1186
BS97
150mm 7-BLADE OUTRIGGER
1356
BS98
150mm 8-BLADE OUTRIGGER
1526
Scale 1:10
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 2
22 / 0 / 60
05/07/11
Component Identification
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
BS102
200mm 2-BLADE OUTRIGGER
BS103
200mm 3-BLADE OUTRIGGER
800
600
BS104
200mm 4-BLADE OUTRIGGER
1000
BS105
200mm 5-BLADE OUTRIGGER
1200
BS106
200mm 6-BLADE OUTRIGGER
1400
BS107
200mm 7-BLADE OUTRIGGER
1600
Scale 1:10
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 1
22 / 0 / 70
05/07/11
Component Identification
System 22
For alternative lengths of brise soleil blade, fixing centres, and
fixing details refer to Metal Technology's Technical Department.
BS143
150mm 5-BLADE
UPRIGGER
BS144
150mm 6-BLADE
UPRIGGER
℄ of
BS146
150mm 8-BLADE
UPRIGGER
℄ of
bracket
℄ of
bracket
bracket
℄ of
1260
1695
1050
1485
840
1275
630
1065
BS145
150mm 7-BLADE
UPRIGGER
℄ of
bracket
ALUMINIUM BRISE
SOLEIL SYSTEM
bracket
℄ of
bracket
BS142
150mm 4-BLADE
UPRIGGER
℄ of
℄ of
bracket
℄ of
bracket
BS140
150mm 2-BLADE
UPRIGGER
℄ of
420
bracket
645
855
bracket
BS141
150mm 3-BLADE
UPRIGGER
435
℄ of
℄ of
bracket
bracket
Scale 1:10
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 1
22 / 0 / 80
22/07/11
Component Identification
System 22
For alternative lengths of brise soleil blade, fixing centres, and
fixing details refer to Metal Technology's Technical Department.
BS152
200mm 4-BLADE
UPRIGGER
BS153
200mm 5-BLADE
UPRIGGER
ALUMINIUM BRISE
SOLEIL SYSTEM
BS154
200mm 6-BLADE
UPRIGGER
BS155
200mm 7-BLADE
UPRIGGER
℄ of
bracket
℄ of
℄ of
bracket
bracket
℄ of
BS151
200mm 3-BLADE
UPRIGGER
bracket
℄ of
bracket
BS150
200mm 2-BLADE
UPRIGGER
℄ of
bracket
℄ of
480
884
1400
2004
bracket
1120
840
1724
℄ of
1444
560
1164
bracket
℄ of
bracket
604
℄ of
bracket
℄ of
bracket
Scale 1:10
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 0
22 / 0 / 90
05/07/11
Section Drawings
System 22
200
150
110
36
ALUMINIUM BRISE
SOLEIL SYSTEM
BS05
150mm BRISE
SOLEIL BLADE
59
BS16
200mm BRISE SOLEIL D SECTION
45
30
83.8
BS06
200mm BRISE SOLEIL BLADE
Scale 1:1
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
BS15
150mm BRISE SOLEIL D SECTION
SHEET
rev 1
22 / 1 / 10
13/01/10
General Arrangement
Cantilevered Panels
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
WALL MOUNTED BRISE SOLEIL
INTEGRAL CURTAIN WALLING
BRISE SOLEIL
Not to scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 2
22 / 2 / 10
05/07/11
General Arrangement
Vertical Panels
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
WALL MOUNTED VERTICAL BRISE SOLEIL
INTEGRAL VERTICAL CURTAIN
WALLING BRISE SOLEIL
Not to scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 3
22 / 2 / 20
05/07/11
General Arrangement
Curtain Walling Assembly Detail
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
HR5033 28mm
thermal break
HR5064 Foil
backed sealant
tape
Brise soleil
stitch plate
CW09 Cover cap
BS80 Bracket pin
Brise soleil curtain
walling bracket
7201
Screw
Not to scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
HR5078 Pressure plate
SHEET
rev 3
22 / 2 / 30
05/07/11
General Arrangement
Brise Soleil Cantilevered off Curtain Walling
System 22
For further guidance on selecting the most suitable combination of brise soleil
blade, bracket, prop, and outrigger please refer to section 6 of this manual.
ALUMINIUM BRISE
SOLEIL SYSTEM
All curtain walling and brise soleil sections, spigots, brackets, and fixings to be sized by a structural
engineer to suit site conditions.
28
26.5
BS53 Brise soleil
stitch plate
Brise soleil curtain
walling bracket
BS77 Grub screw
BS47 Bracket fixing bolt
with BS48 nyloc nut
BS77 Grub screw
BS80
Bracket
pin
BS47 Bracket fixing bolt
with BS48 nyloc nut
Outrigger
Brise soleil D
section
Brise soleil
blade
BS60 Outrigger
packer
BS47 Bracket
fixing bolt with
BS48 nyloc nut
7201 No 10 x 38mm pan
head stainless steel self
tapping screw
BS53 Brise
soleil stitch
plate
BS47 Bracket
fixing bolt with
BS48 nyloc nut
BS80
Bracket
pin
HR5064 Foil
backed sealant
tape
BS77 Grub
screw
Scale 1:4
C
Brise soleil
blade
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Brise soleil
curtain walling
bracket
BS50 Blade
fixing screw
Brise soleil D
section
BS60 Outrigger
packer
BS47 Bracket
fixing bolt with
BS48 nyloc nut
SHEET
rev 5
22 / 2 / 40
05/07/11
General Arrangement
Brise Soleil Cantilevered off Structure
System 22
For further guidance on selecting the most suitable combination of brise soleil
blade, bracket, prop, and outrigger please refer to section 6 of this manual.
ALUMINIUM BRISE
SOLEIL SYSTEM
All brise soleil components, fixings and building structure to be checked by a structural engineer to
ensure they are capable of accommodating the loads imposed on them by the brise soleil.
T brackets come pre-drilled to suit M10 structural fixings.
48.5
Brise soleil T bracket
Outrigger
BS77 Grub screw
BS47 Bracket fixing bolt
with BS48 nyloc nut
BS77 Grub screw
BS47 Bracket fixing bolt
with BS48 nyloc nut
Indicative M10
structural fixings
(by specialist) to
suit application.
Brise soleil
blade
Brise soleil
blade
Brise soleil D
section
BS60 Outrigger
packer
BS50 Blade
fixing screw
BS47 Bracket
fixing bolt with
BS48 nyloc nut
Brise soleil D
section
Brise soleil
T bracket
BS47 Bracket
fixing bolt with
BS48 nyloc nut
BS77 Grub
screw
BS60 Outrigger
packer
BS47 Bracket
fixing bolt with
BS48 nyloc nut
Indicative M10
structural fixings
(by specialist) to
suit application.
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 4
22 / 2 / 50
05/07/11
General Arrangement
Brise Soleil Propped off Curtain Walling
System 22
Suitable for use where the structural capabilities of a cantilevered option are exceeded. ALUMINIUM BRISE
All curtain walling and brise soleil sections, spigots, brackets, and fixings to be sized
SOLEIL SYSTEM
by a structural engineer to suit site conditions.
For optimum performance props to be at 45° angle to curtain walling and outrigger. Where alternative
angles are required, application must be checked and approved by a structural engineer.
BS52 Brise soleil
stitch plate
BS57 Upper prop
curtain walling
bracket
BS45 Prop fixing
bolt with BS48
nyloc nut
7201 No 10 x 38mm pan
head stainless steel self
tapping screw
BS45 Prop fixing
bolt with BS48
nyloc nut
Upper prop to
suit outrigger
BS85 Threaded
adjustment bar
BS52 Brise
soleil stitch
plate
BS112 Lower
prop
BS128 Lower prop
outrigger bracket
BS53 Brise soleil
stitch plate
Brise soleil curtain
walling bracket
BS77 Grub screw
BS45 Prop fixing
bolt with BS48
nyloc nut
BS45 Prop fixing
bolt with BS48
nyloc nut
Brise soleil D
section
45°
BS47 Bracket fixing bolt
with BS48 nyloc nut
BS77 Grub screw
BS47 Bracket fixing bolt
with BS48 nyloc nut
BS80
Bracket
pin
7201 No 10 x 38mm pan
head stainless steel self
tapping screw
VIEW
FROM
ABOVE
BS47 Bracket
fixing bolt with
BS48 nyloc nut
28
Brise soleil
stitch plate
BS52
Brise soleil
blade
Upper prop
to suit
outrigger
BS57 Upper
prop curtain
walling bracket
HR5064 Foil backed
sealant tape
BS45 Prop fixing bolt
with BS48 nyloc nut
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
BS85 Threaded
adjustment bar
Outrigger
BS128 Lower
prop outrigger
bracket
BS112 Lower
prop
Brise soleil D
section
BS45 Prop fixing
bolt with BS48
nyloc nut
SHEET
rev 4
22 / 2 / 60
05/07/11
General Arrangement
Brise Soleil Propped off Structure
System 22
Suitable for use where the structural capabilities of a cantilevered option are exceeded.
All brise soleil components, fixings and building structure to be checked by a structural ALUMINIUM BRISE
SOLEIL SYSTEM
engineer to ensure they are capable of accommodating the loads imposed on them by
the brise soleil.
For optimum performance props to be at 45° angle to curtain walling and outrigger. Where alternative
angles are required, application must be checked and approved by a structural engineer.
BS45 Prop fixing
bolt with BS48
nyloc nut
BS89 Upper prop
"T" bracket
BS45 Prop fixing
bolt with BS48
nyloc nut
Indicative M10
structural fixings
(by specialist) to
suit application.
Upper prop to
suit outrigger
BS85 Threaded
adjustment bar
Indicative M10
structural fixings
(by specialist) to
suit application.
BS112 Lower
prop
BS128 Lower prop
outrigger bracket
Brise soleil T bracket
BS77 Grub screw
BS45 Prop fixing
bolt with BS48
nyloc nut
BS45 Prop fixing
bolt with BS48
nyloc nut
Brise soleil D
section
45°
BS47 Bracket fixing bolt
with BS48 nyloc nut
BS77 Grub screw
BS47 Bracket
fixing bolt with
BS48 nyloc nut
BS47 Bracket fixing bolt
with BS48 nyloc nut
VIEW
FROM
ABOVE
Indicative M10
structural fixings
(by specialist) to
suit application.
Brise soleil
T bracket
Scale 1:4
C
Brise soleil
blade
Upper prop
to suit
outrigger
BS45 Prop fixing
bolt with BS48
nyloc nut
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
BS85 Threaded
adjustment bar
Outrigger
BS128 Lower
prop outrigger
bracket
BS112 Lower
prop
Brise soleil D
section
BS45 Prop fixing
bolt with BS48
nyloc nut
SHEET
rev 4
22 / 2 / 70
22/07/11
General Arrangement
Horizontal Bracket Details
System 22
For further guidance on selecting the most suitable combination of brise soleil
blade, bracket, prop, and outrigger please refer to section 6 of this manual.
ALUMINIUM BRISE
SOLEIL SYSTEM
All curtain walling and brise soleil sections, spigots, brackets, and fixings to be
sized by a structural engineer to suit site conditions.
CAPPED CURTAIN WALLING DETAIL
BS80 Bracket pin
28
BS53 Brise soleil
stitch plate
CW09 Cover cap
Neutral cure silicone seal
between brise soleil
bracket and stitch plate
BS70 (150mm blades)
BS71 (200mm blades)
HR5064 Foil backed
sealant tape
Neutral cure silicone seal
between cover cap and
brise soleil bracket
BS77 Grub screw
WALL MOUNTED BRACKET DETAIL
BS87 (150mm blades)
BS88 (200mm blades)
BS77 Grub screw
Scale 1:2
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
M10 fixing (size and type
selected by fabricator to
suit application)
Fabricator to ensure the structure and
fixings are capable of accommodating the
loads imposed on them by the Brise Soleil.
SHEET
rev 3
22 / 2 / 80
22/07/11
General Arrangement
Horizontal Bracket Details
System 22
For further guidance on selecting the most suitable combination of brise soleil
blade, bracket, prop, and outrigger please refer to section 6 of this manual.
ALUMINIUM BRISE
SOLEIL SYSTEM
All curtain walling and brise soleil sections, spigots, brackets, and fixings to be
sized by a structural engineer to suit site conditions.
SILICONE POINTED CURTAIN WALLING DETAIL
32
BS80 Bracket pin
Neutral cure black silicone weather seal
with closed cell non-gassing polyethylene
foam backer rod (by others).
BS70 (150mm blades)
BS71 (200mm blades)
Scale 1:2
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
BS77 Grub screw
SHEET
rev 2
22 / 2 / 90
05/07/11
General Arrangement
Vertical Brise Soleil off Curtain Walling
System 22
For further guidance on selecting the most suitable combination of brise soleil
blade, bracket, and uprigger please refer to section 6 of this manual.
ALUMINIUM BRISE
SOLEIL SYSTEM
All curtain walling and brise soleil sections, spigots, brackets, and fixings to be sized by a structural
engineer to suit site conditions.
28
82
BS51 Brise soleil
stitch plate
BS69 Brise soleil curtain
walling bracket
Brise soleil
blade
Uprigger
BS47 Bracket fixing bolt
with BS48 nyloc nut
BS80
Bracket
pin
BS77 Grub screw
7201 No 10 x 38mm pan
head stainless steel self
tapping screw
BS51 Brise
soleil stitch
plate
BS80
Bracket
pin
HR5064 Foil
backed sealant
tape
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Brise soleil
blade
BS47 Bracket
fixing bolt with
BS48 nyloc nut
BS50 Blade
fixing screw
Brise soleil
curtain walling
bracket
SHEET
rev 2
22 / 2 / 100
05/07/11
General Arrangement
Vertical Brise Soleil off Structure
System 22
For further guidance on selecting the most suitable combination of brise soleil
blade, bracket, prop, and outrigger please refer to section 6 of this manual.
ALUMINIUM BRISE
SOLEIL SYSTEM
All brise soleil components, fixings and building structure to be checked by a structural engineer
to ensure they are capable of accommodating the loads imposed on them by the brise soleil.
T brackets come pre-drilled to suit M10 structural fixings.
100
BS87 Brise soleil
"T" bracket
Brise soleil
blade
Uprigger
BS47 Bracket fixing bolt
with BS48 nyloc nut
BS77 Grub screw
Indicative M10
structural fixings
(by specialist) to
suit application.
BS87 Brise soleil
"T" bracket
BS47 Bracket
fixing bolt with
BS48 nyloc nut
BS50 Blade
fixing screw
Brise soleil
blade
Indicative M10 structural
fixings (by specialist) to
suit application.
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 2
22 / 2 / 110
05/07/11
General Arrangement
Vertical Bracket Details
System 22
For further guidance on selecting the most suitable combination of brise soleil
blade, bracket, prop, and outrigger please refer to section 6 of this manual.
ALUMINIUM BRISE
SOLEIL SYSTEM
All curtain walling and brise soleil sections, spigots, brackets, and fixings to be
sized by a structural engineer to suit site conditions.
CAPPED CURTAIN WALLING DETAIL
BS80 Bracket pin
28
BS53 Brise soleil
stitch plate
CW09 Cover cap
Neutral cure silicone seal
between brise soleil
bracket and stitch plate
BS69 Vertical brise soleil
curtain walling bracket
HR5064 Foil backed
sealant tape
Neutral cure silicone seal
between cover cap and
brise soleil bracket
BS77 Grub screw
WALL MOUNTED BRACKET DETAIL
BS87 Brise soleil
"T" bracket
BS77 Grub screw
Scale 1:2
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
M10 fixing (size and type
selected by fabricator to
suit application)
Fabricator to ensure the structure and
fixings are capable of accommodating the
loads imposed on them by the Brise Soleil.
SHEET
rev 2
22 / 2 / 120
05/07/11
General Arrangement
Vertical Bracket Details
System 22
For further guidance on selecting the most suitable combination of brise soleil
blade, bracket, prop, and outrigger please refer to section 6 of this manual.
ALUMINIUM BRISE
SOLEIL SYSTEM
All curtain walling and brise soleil sections, spigots, brackets, and fixings to be
sized by a structural engineer to suit site conditions.
SILICONE POINTED CURTAIN WALLING DETAIL
32
BS80 Bracket pin
BS69 Vertical brise soleil
curtain walling bracket
Neutral cure black silicone weather seal
with closed cell non-gassing polyethylene
foam backer rod (by others).
BS77 Grub screw
Scale 1:2
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 2
22 / 2 / 130
05/07/11
General Notes
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
System 22 Brise Soleil is designed for horizontal or vertical applications. The system has been designed to
be wall mounted or used in conjunction with System 17 curtain walling. The standard curtain walling
brackets are designed to be used with 28mm glazing and CW09 cover caps only. They may also be used in
conjunction with System 17 Latitude and SP silicone pointed applications where a wider variety of unit
thicknesses may be accommodated. HR50121 push-in gasket is not suitable for use with brise soleil
brackets.
In a curtain walling applications fabricators must ensure the centre line of brackets are positioned a
minimum distance from the top of the mullions and expansion joints, as follows:
BS69 bracket - 200mm
BS70 bracket - 250mm
BS71 bracket - 250mm
BS57 bracket - 105mm
The standard brise soleil system is not designed for use in façetted applications. However, where façets are
required bespoke solutions may be possible on a project-by-project basis.
The design of the brise soleil system takes into consideration the structural capabilities of the blades, the
brackets, the outriggers/upriggers, their fixings, and their attachment to the curtain walling mullion. It
must be noted however that the brise soleil will impose loads onto the curtain walling mullion and its
fixings to the building structure, which must be determined by a structural engineer and catered for when
selecting the appropriate curtain walling profiles and structural fixings.
Horizontal Brise Soleil using BS05 150mm blade:
BS80
bracket pin
BS77 grub
screw
BS47 fixing
bolt
BS48 nyloc
nut
BS53 stitch
plate
7201 stitch
plate fixing
screw
1
12
Number of
panels -1
4
2
3
3
1
2
BS93/LH x 1 Number of
BS93/RH x 1 panels +1
3
1
16
Number of
panels -1
4
2
3
3
1
2
BS94/LH x 1 Number of
BS94/RH x 1 panels +1
4
1
20
Number of
panels -1
4
2
3
3
1
2
BS95/LH x 1 Number of
BS95/RH x 1 panels +1
5
1
24
Number of
panels -1
4
2
3
3
1
2
BS96/LH x 1 Number of
BS96/RH x 1 panels +1
6
1
28
Number of
panels -1
4
2
3
3
1
2
BS97/LH x 1 Number of
BS97/RH x 1 panels +1
7
1
32
Number of
panels -1
4
2
3
3
1
2
BS98/LH x 1 Number of
BS98/RH x 1 panels +1
8
1
36
Number of
panels -1
4
2
3
3
1
2
BS60
outrigger
packer*
BS50 fixing
screw
2
BS70
bracket
BS92/LH x 1 Number of
BS92/RH x 1 panels +1
Outrigger
BS15 D
section
Requirements per bracket
BS05 blade
Requirements per panel
* Not required for propped applications.
SHEET
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
rev 2
22 / 3 / 10
06/12/10
General Notes
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
Horizontal Brise Soleil using BS06 200mm blade:
BS80
bracket pin
BS77 grub
screw
BS47 fixing
bolt
BS48 nyloc
nut
BS53 stitch
plate
7201 stitch
plate fixing
screw
1
12
Number of
panels -1
4
2
3
3
1
2
BS103/LH x 1 Number of
BS103/RH x 1 panels +1
3
1
16
Number of
panels -1
4
2
3
3
1
2
BS104/LH x 1 Number of
BS104/RH x 1 panels +1
4
1
20
Number of
panels -1
4
2
3
3
1
2
BS105/LH x 1 Number of
BS105/RH x 1 panels +1
5
1
24
Number of
panels -1
4
2
3
3
1
2
BS106/LH x 1 Number of
BS106/RH x 1 panels +1
6
1
28
Number of
panels -1
4
2
3
3
1
2
BS107/LH x 1 Number of
BS107/RH x 1 panels +1
7
1
32
Number of
panels -1
4
2
3
3
1
2
BS60
outrigger
packer*
BS50 fixing
screw
2
BS71
bracket
BS102/LH x 1 Number of
BS102/RH x 1 panels +1
Outrigger
BS16 D
section
Requirements per bracket
BS06 blade
Requirements per panel
* Not required for propped applications.
Horizontal Brise Soleil Propped off Curtain Walling
For optimum performance props to be at a 45° angle to curtain walling and outrigger. Where alternative
angles are required, applications must be checked and approved by a structural engineer.
Additional components required for propped applications:
Number of upper props = (Number of panels) + 1
BS45 prop fixing bolt = (Number of props) x 2
BS47 fixing bolt = Number of props
BS48 nyloc nut = (Number of props) x 3
BS52 stitch plate = Number of props
BS57 upper prop curtain wall bracket = Number of props
BS80 bracket pin = (Number of props) x 4
7201 stitch plate fixing screw = (Number of props) x 2
BS85 threaded bar = Number of props
BS112 lower prop = Number of props
BS128 lower prop outrigger bracket = Number of props
From the tables below select the appropriate upper prop to suit outrigger.
150mm Brise Soleil:
200mm Brise Soleil:
Outrigger
reference
Outrigger
reference
BS94
BS95
BS96
BS97
BS98
Upper prop
reference
BS114
BS115
BS116
BS117
BS118
BS103
BS104
BS105
BS106
BS107
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Upper prop
reference
BS133
BS134
BS135
BS136
BS137
SHEET
rev 1
22 / 3 / 20
15/07/10
General Notes
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
Vertical Brise Soleil
To facilitate ease of maintenance, vertical panel configurations have been designed so that any
individual panel in a vertical array can be removed without disturbing the adjacent panels.
Where a vertical brise soleil uprigger is secured using two brackets which straddle an expansion joint,
careful consideration must be given to the movement of the curtain walling relative to the brise soleil.
The closest distance from the glass to the blade is set at 82mm for the vertical system. Where greater
clearance is required additional bespoke components will be necessary. Refer to Metal Technology's
Technical Department for guidance.
The vertical separation of the blades is set to standard fixed dimensions for the 150mm and 200mm
options. Alternative spacings may be provided on request for bespoke applications.
BS77 grub
screw
BS47 fixing
bolt
BS48 nyloc
nut
BS51 stitch
plate
7201 stitch
plate fixing
screw
BS140/LH x 1
BS140/RH x 1
(1 x BS69 per
panel) + 1
2
8
4
1
1
1
1
2
BS141/LH x 1
BS141/RH x 1
(1 x BS69 per
panel) + 1
3
12
4
1
1
1
1
2
BS142/LH x 1
BS142/RH x 1
(2 x BS69 per
panel) + 2
4
16
4
1
1
1
1
2
BS143/LH x 1
BS143/RH x 1
(2 x BS69 per
panel) + 2
5
20
4
1
1
1
1
2
BS144/LH x 1
BS144/RH x 1
(2 x BS69 per
panel) + 2
6
24
4
1
1
1
1
2
BS145/LH x 1
BS145/RH x 1
(2 x BS69 per
panel) + 2
7
28
4
1
1
1
1
2
BS146/LH x 1
BS146/RH x 1
(2 x BS69 per
panel) + 2
8
32
4
1
1
1
1
2
Uprigger
BS80
bracket pin
Requirements per bracket
BS50 fixing
screw
Requirements
per panel
BS05 blade
Number of
brackets per
horizontal row
Vertical Brise Soleil using BS05 150mm blade:
SHEET
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
rev 1
22 / 3 / 30
07/12/10
General Notes
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
BS77 grub
screw
BS47 fixing
bolt
BS48 nyloc
nut
BS51 stitch
plate
7201 stitch
plate fixing
screw
BS150/LH x 1
BS150/RH x 1
(1 x BS69 per
panel) + 1
2
8
4
1
1
1
1
2
BS151/LH x 1
BS151/RH x 1
(2 x BS69 per
panel) + 2
3
12
4
1
1
1
1
2
BS152/LH x 1
BS152/RH x 1
(2 x BS69 per
panel) + 2
4
16
4
1
1
1
1
2
BS153/LH x 1
BS153/RH x 1
(2 x BS69 per
panel) + 2
5
20
4
1
1
1
1
2
BS154/LH x 1
BS154/RH x 1
(2 x BS69 per
panel) + 2
6
24
4
1
1
1
1
2
BS155/LH x 1
BS155/RH x 1
(2 x BS69 per
panel) + 2
7
28
4
1
1
1
1
2
Uprigger
BS80
bracket pin
Requirements per bracket
BS50 fixing
screw
Requirements
per panel
BS05 blade
Number of
brackets per
horizontal row
Vertical Brise Soleil using BS06 200mm blade:
Wall Mounted Applications
For wall fixed applications where applicable please make the following changes:
Replace BS69 curtain walling bracket with BS87 "T" bracket
Replace BS70 curtain walling bracket with BS87 "T" bracket
Replace BS71 curtain walling bracket with BS88 "T" bracket
Replace BS57 upper prop curtain walling bracket with BS89 upper prop "T" bracket
Omit BS80 bracket pins, 7201 screws and BS51/BS52/BS53 stitch plates.
It is possible to support a curtain walling fixed horizontal brise soleil panel using wall mounted upper
prop brackets. However, as the surface of the wall is unlikely to be flush with the curtain walling,
fabricators are advised to set out the application to determine the prop length requirements on a
project-by-project basis.
When securing a wall mounted brise soleil bracket or wall mounted prop bracket directly to the building
structure the fabricator must consult a specialist anchor supplier and/or structural engineer to
determine the most suitable fixing method. Care must be taken to ensure that the applicable building
structure is capable of accommodating the loads imposed on it by the brise soleil assembly. Final
approval for the brise soleil fixing to structure should be obtained from the structural engineer
responsible for the building.
SHEET
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
rev 1
22 / 3 / 40
07/12/10
Fabrication Sizes
Horizontal Brise Soleil
System 22
Outrigger length
ALUMINIUM BRISE
SOLEIL SYSTEM
Blade length = span - 22mm
6
6
D section length = span - 22mm
5
5
Span
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 4
22 / 4 / 10
07/07/11
Mullion Prep for Horizontal Brise
Soleil Brackets
System 22
Jig drilled method:
ALUMINIUM BRISE
SOLEIL SYSTEM
1. Mark centre line of brise soleil bracket on side wall of mullion.
2. Insert BS70 (150mm blade) or BS71 (200mm blade) bracket into nose of curtain walling mullion, and
align with centre line marked on mullion.
3. Place JIG22002 jig over brise soleil bracket allowing nose of bracket to protrude through slot in jig.
4. Align centre line on jig with centre line marked on side wall of mullion, and clamp jig in position.
5. Align brise soleil bracket with locating lines "B" for BS70 (150mm blade) or lines "C" for BS71 (200mm
blade) marked at either end of slot in jig.
6. Clamp brise soleil bracket to curtain walling mullion using thumbturns on jig.
7. Drill 6mm holes through nose of curtain walling mullion and brise soleil bracket using drill bushes
marked "B" for BS70 (150mm blade) or marked "C" for BS71 (200mm blade) on jig.
8. Remove jig and insert BS80 bracket pins through nose of mullion and brise soleil bracket.
CNC method:
1. Prep holes in mullion using CNC machine.
2. Insert BS70 (150mm blade) or BS71 (200mm blade) bracket into nose of curtain walling mullion, and
centre/align to chosen position.
3. Use pre-drilled holes in mullion as jig for drilling holes in brise soleil bracket.
4. Insert BS80 bracket pins through nose of mullion and brise soleil bracket.
7
6mm diameter
holes to suit
BS80 bracket
pin
Scale 1:4
C
Bushes
for 6mm
diameter
drill
BS70/BS71
30
300mm (for 150mm brise soleil)
327mm (for 200mm brise soleil)
30
BS70/BS71
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
℄ marked on
mullion
℄ of brise
soleil
bracket
Bushes
for 6mm
diameter
drill
Locating lines
"B" for BS70 and
"C" for BS71 to
position brise
soleil bracket
SHEET
rev 3
22 / 4 / 20
07/12/10
Upper Prop Bracket Setting-out
Detail off Curtain Walling
System 22
All dimensions "X" are based on the prop angled at 45° to the horizontal outrigger.
Where these parameters vary fabricator must set out the application to determine
the "X" dimension on a project-by-projest basis.
ALUMINIUM BRISE
SOLEIL SYSTEM
℄ of BS57 upper prop
40
Dimension "X"
curtain walling bracket
45°
℄ of outrigger
150mm Brise Soleil
200mm Brise Soleil
Outrigger
Outrigger
BS94
BS95
BS96
BS97
BS98
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Dimension "X"
822.5mm
992.5mm
1162.5mm
1332.5mm
1502.5mm
BS103
BS104
BS105
BS106
BS107
Dimension "X"
749.5mm
949.5mm
1149.5mm
1349.5mm
1549.5mm
SHEET
rev 3
22 / 4 / 30
07/07/11
Mullion Prep for BS57 Bracket
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
Jig drilled method:
1. Mark centre line of upper prop bracket on side wall of mullion.
2. Insert upper prop bracket BS57 into nose of curtain walling mullion, and align with centre line marked
on mullion.
3. Place JIG22002 jig over upper prop bracket allowing nose of bracket to protrude through slot in jig.
4. Align centre line on jig with centre line marked on side wall of mullion, and clamp jig in position.
5. Align upper prop bracket with locating lines "A" marked at either end of slot in jig.
6. Clamp BS57 upper prop bracket to curtain walling mullion using thumbturn on jig.
7. Drill 6mm holes through nose of curtain walling mullion and upper prop bracket using drill bushes
marked "A" on jig.
8. Remove jig and insert BS80 bracket pins through nose of mullion and upper prop bracket.
CNC method:
1. Prep holes in mullion using CNC machine.
2. Insert BS57 upper prop bracket into nose of curtain walling mullion, and centre/align to chosen position.
3. Use pre-drilled holes in mullion as jig for drilling holes in upper prop bracket.
4. Insert BS80 bracket pins through nose of mullion and upper prop bracket.
7
BS57
℄ marked on
mullion
30
BS57
Dimension "X"
30
50
℄
6mm diameter
holes to suit
BS80 bracket
pin
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Bushes
for 6mm
diameter
drill
of BS57 upper
prop curtain
walling bracket
Locating lines
"A" to position
brise soleil
bracket
SHEET
rev 2
22 / 4 / 40
07/07/11
Upper Prop Bracket Setting-out
Detail off Structure
System 22
All dimensions "X" are based on the prop angled at 45° to the horizontal outrigger.
Where these parameters vary fabricator must set out the application to determine
the "X" dimension on a project-by-projest basis.
ALUMINIUM BRISE
SOLEIL SYSTEM
50
75
℄ of BS89 upper prop
50
"T" bracket
BS89 upper prop
"T" bracket
Dim "A"
Dim "A"
60
Dimension "X"
75
Brise soleil "T" bracket
For BS87 Dim "A" =75mm
For BS88 Dim "A" =88.5mm
150mm Brise Soleil
200mm Brise Soleil
Outrigger
Outrigger
BS94
BS95
BS96
BS97
BS98
Scale 1:4
C
45°
℄ of outrigger
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Dimension "X"
837mm
1007mm
1177mm
1347mm
1517mm
BS103
BS104
BS105
BS106
BS107
Dimension "X"
764mm
964mm
1164mm
1364mm
1564mm
SHEET
rev 3
22 / 4 / 50
07/07/11
Outrigger Prep for Lower Prop
Bracket
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
When using prop, drill additional 11mm diameter hole in end of outriggers, as indicated, to accommodate
BS128 lower prop outrigger bracket.
Outrigger for 150mm blade 15mm
Outrigger for 200mm blade 28.5mm
BS128 Lower prop
outrigger bracket
35
1
Ø1
Existing 11mm
diameter hole
pre-drilled in
outrigger
℄
Scale 1:1
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 3
22 / 4 / 60
07/07/11
Fabrication Sizes
Vertical Brise Soleil
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
6
6
Blade length = span - 22mm
5
5
Span
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 3
22 / 4 / 70
07/07/11
Mullion Prep for Vertical Brise
Soleil Brackets
System 22
Jig drilled method:
ALUMINIUM BRISE
SOLEIL SYSTEM
1. Mark centre line of brise soleil bracket on side wall of mullion.
2. Insert BS69 vertical brise soleil bracket into nose of curtain walling mullion, and align with centre line
marked on mullion.
3. Place JIG22002 jig over BS69 vertical brise soleil bracket allowing nose of bracket to protrude through
slot in jig.
4. Align centre line on jig with centre line marked on side wall of mullion, and clamp jig in position.
5. Align BS69 vertical brise soleil bracket with locating lines "D" marked at either end of slot in jig.
6. Clamp BS69 vertical brise soleil bracket to curtain walling mullion using thumbturns on jig.
7. Drill 6mm holes through nose of curtain walling mullion and brise soleil bracket using drill bushes
marked "D" on jig.
8. Remove jig and insert BS80 bracket pins through nose of mullion and brise soleil bracket.
CNC method:
1. Prep holes in mullion using CNC machine.
2. Insert BS69 vertical brise soleil bracket into nose of curtain walling mullion, and centre/align to chosen
position.
3. Use pre-drilled holes in mullion as jig for drilling holes in brise soleil bracket.
4. Insert BS80 bracket pins through nose of mullion and brise soleil bracket.
7
30
BS69
6mm diameter
holes to suit
BS80 bracket
pin
Bushes
for 6mm
diameter
drill
BS69
℄ marked on
30
200
mullion
℄ of brise
soleil
bracket
Locating lines
"D" to position
brise soleil
bracket
Bushes
for 6mm
diameter
drill
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 3
22 / 4 / 80
07/07/11
Bracket Setting out Dimensions
150mm Vertical Brise Soleil
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
℄ of
bracket
420*
420*
℄ of
℄ of
℄ of
bracket
℄ of
bracket
bracket
℄ of
420*
bracket
bracket
420*
℄ of
bracket
420*
℄ of
℄ of
bracket
℄ of
bracket
bracket
420**
BS140
bracket
BS144
℄ of
BS145
1260
bracket
BS146
1050
℄ of
840
630
BS143
420*
℄ of
℄ of
bracket
420**
bracket
℄ of
℄ of
420
℄ of
bracket
bracket
℄ of
℄ of
420**
BS142
420**
bracket
℄ of
bracket
bracket
420**
℄ of
*
℄ of
bracket
If using uprigger BS141 above,
this dimension is 549.5mm
** If using uprigger BS141 below,
this dimension is 500.5mm
420**
bracket
bracket
℄ of
bracket
Scale 1:10
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 0
22 / 4 / 90
07/07/11
Bracket Setting out Dimensions
200mm Vertical Brise Soleil
℄ of
bracket
bracket
ALUMINIUM BRISE
SOLEIL SYSTEM
℄ of
bracket
BS150
℄ of
560*
bracket
560*
560*
℄
℄ of
560*
* If using
uprigger BS151
above or below,
this dimension
is 460mm
of
bracket
System 22
℄ of
℄ of
bracket
bracket
℄
560*
of
bracket
℄ of
bracket
BS153
℄ of
BS155
1120
BS154
560*
1400
840
bracket
℄ of
bracket
℄ of
560*
BS152
560
bracket
℄ of
bracket
bracket
℄ of
bracket
560*
℄ of
560*
℄ of
bracket
℄ of
℄ of
bracket
Scale 1:10
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
560*
bracket
℄ of
bracket
SHEET
rev 0
22 / 4 / 100
07/07/11
Pressure Plate and Cover Cap Preps
Horizontal brise soleil curtain walling brackets are designed to be used with
CW09 cover cap only.
Vertical brise soleil curtain walling brackets are designed to be used with the
following cover caps only: CW06, CW08A, CW09, CW50, HR5008.
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
Ø7
350mm for
450mm for
450mm for
160mm for
107mm for BS69
107mm for BS70
134mm for BS71
57mm for BS57
BS69
BS70
BS71
BS57
Ø7
Ø7
10
Not to scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Ø7
10
10
SHEET
rev 0
22 / 4 / 110
07/07/11
Brise Soleil Stitch Plate Application
PVC Pressure Plate
System 22
1. Insert units into curtain walling screen as per "Glazing Procedure" in System 17
ALUMINIUM BRISE
manual.
SOLEIL SYSTEM
2. Prep cut length of HR5064 foil-backed sealant tape with single central slit to
accommodate projecting nose of applicable bracket.
3. Apply cut length of HR5064 foil-backed sealant tape over glass and nose of bracket. (If using HR5064
throughout the curtain walling screen, simply slit tape as required.)
4. Apply pressure plate, passing brise soleil bracket through pre-prepped slot, in accordance with System
17 "Glazing Procedure", ensuring standard pressure plate fixings do not interfere with brise soleil
brackets.
5. Seal between projecting nose of brise soleil bracket and slot in pressure plate. Seal superfluous
pre-punched pressure plate holes as required.
6. Apply brise soleil stitch plate and centralise over brise soleil bracket, fixing into nose of curtain walling
mullion using 7201 stitch plate screws. Torque brise soleil stitch plate fixings to 3.5Nm.
7. Snap-fit CW09 cover cap into place passing brise soleil bracket through pre-prepped slot in cover cap.
8. Seal between projecting nose of brise soleil bracket and slot in cover cap.
BS53
Brise
soleil
stitch
plate
25
BS51
Brise
soleil
stitch
plate
25
BS52
Brise
soleil
stitch
plate
Scale 1:4
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
400mm
600mm
700mm
700mm
for
for
for
for
BS57
BS69
BS70
BS71
57mm slit for BS57
107mm slit for BS69
107mm slit for BS70
134mm slit for BS71
130
450
500
25
BS51
Brise
soleil
stitch
plate
C
130
350
60
400
25
BS52
Brise
soleil
stitch
plate
18.5
173
210
18.5
7201 screw
BS53
Brise
soleil
stitch
plate
HR5064 Foil
backed sealant
tape
SHEET
rev 0
22 / 4 / 120
07/07/11
Brise Soleil Stitch Plate Application
Aluminium Pressure Plate
System 22
1. Insert units into curtain walling screen as per "Glazing Procedure" in System 17
ALUMINIUM BRISE
manual.
SOLEIL SYSTEM
2. Prep cut length of HR5064 foil-backed sealant tape with single central slit to
accommodate projecting nose of applicable bracket.
3. Apply cut length of HR5064 foil-backed sealant tape over glass and nose of bracket. (If using HR5064
throughout the curtain walling screen, simply slit tape as required.)
4. Apply pressure plate, passing brise soleil bracket through pre-prepped slot, in accordance with System
17 "Glazing Procedure", ensuring standard pressure plate fixings do not interfere with brise soleil
brackets.
5. Seal between projecting nose of brise soleil bracket and slot in pressure plate. Seal superfluous
pre-punched pressure plate holes as required.
6. Apply brise soleil stitch plate and centralise over brise soleil bracket, fixing into nose of curtain walling
mullion using 7201 stitch plate screws. Torque brise soleil stitch plate fixings to 3.5Nm.
7. Snap-fit CW09 cover cap into place passing brise soleil bracket through pre-prepped slot in cover cap.
8. Seal between projecting nose of brise soleil bracket and slot in cover cap.
BS53
Brise
soleil
stitch
plate
25
BS51
Brise
soleil
stitch
plate
25
Scale 1:4
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
400mm
600mm
700mm
700mm
for
for
for
for
BS57
BS69
BS70
BS71
57mm slit for BS57
107mm slit for BS69
107mm slit for BS70
134mm slit for BS71
450
500
25
BS51
Brise
soleil
stitch
plate
C
130
350
60
400
25
BS52
Brise
soleil
stitch
plate
18.5
173
210
18.5
7201 screw
130
BS52
Brise
soleil
stitch
plate
BS53
Brise
soleil
stitch
plate
HR5064 Foil
backed sealant
tape
SHEET
rev 0
22 / 4 / 130
07/07/11
Horizontal Panel Assembly Detail
System 22
Manufacture brise soleil panel by securing pre-cut blades and D section to
outriggers using BS50 blade fixing screws. Apply suitable thread locking
ALUMINIUM BRISE
SOLEIL SYSTEM
adhesive in accordance with the manufacturers recommendations to prevent
BS50 blade fixing screws from working loose.
BS50 Blade
fixing screw
Blade
D section
BS50 Blade
fixing screw
Outrigger
Outrigger
Blade
Not to scale
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 1
22 / 5 / 10
22/07/10
Vertical Panel Assembly Detail
System 22
Manufacture brise soleil panel by securing pre-cut blades to upriggers using
BS50 blade fixing screws. Apply suitable thread locking adhesive in
ALUMINIUM BRISE
SOLEIL SYSTEM
accordance with the manufacturers recommendations to prevent BS50 blade
fixing screws from working loose.
BS50 Blade
fixing screw
Blade
BS50 Blade
fixing screw
Uprigger
Uprigger
Blade
Not to scale
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 1
22 / 5 / 20
22/07/10
Installation/Assembly Procedure
Cantilevered Curtain Walling Applications
System 22
1.
Secure brise soleil brackets to curtain wall mullion using 4 x BS80 bracket pins, ALUMINIUM BRISE
ensuring pins are centred in mullion nose. Bracket must be correctly
SOLEIL SYSTEM
orientated, with the threaded holes located as shown. Pins may be factory
fitted, or fitted on site prior to installation, at the fabricators discretion.
2. Install curtain walling grid in accordance with the recommendations of the System 17 curtain walling
manual.
3. Check the line and level of the brise soleil brackets to ensure they run through at the correct height
relative to the setting out datum. Adjust grid accordingly if required.
4. For silicone pointed mullions continue the curtain walling installation in accordance with the System
17 Latitude/SP manuals, up to and including gaskets and glazing. Continue silicone pointing between
glass units over brise soleil brackets and both sides of projecting nose. HR50121 push-in gasket is
not suitable for use with brise soleil brackets.
5. For pressure plate and cover cap applications push thermal isolator into nose of mullion, butting up
against bracket as indicated.
a. Continue the curtain walling installation in accordance with the System 17 manual, up to and
including gaskets, glazing and pressure plates ensuring that the brise soleil bracket protrudes
through the pre-prepped slot in the pressure plate. Ensure that standard pressure plate fixings
adjacent to brise soleil brackets are within 300mm of the brise soleil stitch plate fixings.
b. Using a low-modulus silicone sealant, fill and seal all voids between the projecting nose of the
brise soleil brackets and the slots in the pressure plate.
c. Position brise soleil stitch plates centrally over projecting nose of brise soleil brackets. See also
"Brise Soleil Stitch Plate Application" sheet.
d. Apply CW09 cover caps to curtain wall screen ensuring nose of brise soleil bracket protrudes through
pre-prepped slot in cover cap, and seal.
6. Fit the 2 No BS77 grub screws into the threaded holes in the brise soleil bracket (as shown in
Diagram 1) ensuring that the screw is projecting equally on each side.
7. Locate brise soleil panel between adjacent brise soleil brackets and lower into position locating lower
slots over lower grub screws as shown (Diagram 2). Slide brise soleil panel towards screen (Diagram
3), locating upper slot over upper grub screw (Diagram 4). Brise soleil panel is now temporarily held
in position.
8. Repeat procedure with adjacent panel
9. Secure adjacent panels by inserting 2 x BS47 bracket fixing bolts through clear holes in outriggers
and brise soleil bracket, and fix with BS48 nyloc nuts (Diagram 5). Brise soleil panels must not be left
unattended without bolting permanently into position.
10. Repeat procedure along length of brise soleil screen.
11. Centre BS60 outrigger packer between adjacent outriggers at pre-drilled hole behind D section and
secure with BS47 bracket fixing bolt and BS48 nyloc nut.
12. Check line and level of brise soleil panels and finally tighten all BS47 / BS48 fixings.
Thermal
isolator
Curtain
walling
mullion
Brise soleil
bracket
Threaded
hole
BS80
Bracket pin
Threaded
hole
Thermal
isolator
Not to scale
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Diagram 2
Diagram 1
Diagram 3
Diagram 5
Fit BS77
grub screw
Diagram 4
BS47 Bracket fixing bolt
with BS48 nyloc nut
SHEET
rev 2
22 / 5 / 30
10/12/10
Installation/Assembly Procedure
Propped Curtain Walling Applications
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
1. Follow step 1 of "Cantilevered Curtain Walling Applications" instructions.
2. Secure BS57 upper prop curtain walling brackets to curtain walling mullion using 4 x BS80 bracket pins,
ensuring pins are centred in mullion nose. Pins may be factory fitted or fitted on site prior to installation
at the fabricators discretion.
3. Follow steps 2 to 10 inclusive of "Cantilevered Curtain Walling Applications".
4. Locate BS128 lower prop outrigger brackets between adjacent outriggers using 2 x BS47 bracket fixing
bolts through 2 x 11mm diameter holes in outriggers, and secure using BS48 nyloc nuts. See also
"Outrigger Prep for Lower Prop Bracket" sheet.
5. Adjust the level of the brise soleil panels and tighten the BS47 and BS48 fixings at the BS70/BS71 brise
soleil curtain walling brackets.
6. Join BS112 lower prop to correct upper prop using BS85 threaded adjustment bar, ensuring threaded
bar is located equally into both prop components leaving an adjustment gap of 40mm.
BS85 Threaded
adjustment bar
Adjustment gap
50
BS112 Lower
prop
40
50
Upper prop
7. Locate upper prop over BS57 upper prop curtain walling bracket and secure with BS45 prop fixing bolt
and BS48 nyloc nut.
8. Locate BS112 lower prop over BS128 lower prop outrigger bracket, using BS85 threaded adjustment
bar if required to adjust length of prop assembly to suit, and secure with BS45 prop fixing bolt and
BS48 nyloc nut.
9. Check line and level of brise soleil panels and finally tighten all BS45, BS47 and BS48 fixings.
Scale 1:4
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 1
22 / 5 / 40
22/07/10
Installation/Assembly Procedure
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
Cantilevered Wall Mounted Applications
1. Establish setting out position of wall mounted brise soleil brackets on building structure. Care must be
taken to accurately space and level all brackets, as adjustment after fixing may not be possible.
2. Secure wall-mounted T brackets (BS87 or BS88) to building structure using suitable anchor fixings.
Fabricator must consult a specialist anchor supplier and/or structural engineer to determine the most
suitable fixing method. Care must be taken to ensure that the applicable building structure is capable
of accommodating the loads imposed on it by the brise soleil assembly. Final approval for the brise
soleil fixing to the structure should be obtained from the structural engineer responsible for the
building.
3. Follow steps 6 to 12 inclusive of "Cantilevered Curtain Walling Applications" instructions.
Propped Wall Mounted Applications
1. Repeat steps 1 and 2 of the "Cantilevered Wall Mounted Applications" for the BS87/BS88, and the
BS89 upper prop T bracket.
2. Follow steps 6 to 10 inclusive of "Cantilevered Curtain Walling Applications" instructions.
3. Locate BS128 lower prop outrigger brackets between adjacent outriggers using BS47 bracket fixing
bolts through 2 x 11mm diameter holes in outriggers and secure using BS48 nyloc nuts. See also
"Outrigger Prep for Lower Prop Bracket" sheet.
4. Adjust level of brise soleil panels and tighten BS47 and BS48 fixings at BS87/BS88 wall mounted T
brackets.
5. Join BS112 lower prop to correct upper prop using BS85 threaded adjustment bar, ensuring threaded
bar is located equally into both prop components leaving an adjustment gap of 60mm.
6. Locate upper prop over BS89 upper prop T bracket and secure with BS45 prop fixing bolt and BS48
nyloc nut.
7. Locate BS112 lower prop over BS128 lower prop outrigger bracket using BS85 threaded adjustment
bar, if required, to adjust length of prop assembly to suit, (ensure thread engagement of BS85
threaded adjustment bar into upper/lower prop components is minimum 20mm) and secure with BS45
prop fixing bolt and BS48 nyloc nut.
8. Check line and level of brise soleil panels and finally tighten all BS45, BS47 and BS48 fixings.
Wall Mounted Prop with Curtain Walling Brise Soleil
It is possible to support a curtain walling fixed brise soleil panel using wall mounted upper prop brackets
following the "Propped Wall Mounted" details above. However, as the surface of the wall is unlikely to be
flush with the curtain walling, fabricators are advised to set out the application to determine the prop
length requirements on a project-by-project basis.
SHEET
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
rev 0
22 / 5 / 50
26/07/10
Installation/Assembly Procedure
Vertical Curtain Walling Applications
System 22
1.
Secure brise soleil brackets to curtain wall mullion using 4 x BS80 bracket pins, ALUMINIUM BRISE
ensuring pins are centred in mullion nose. Bracket must be correctly
SOLEIL SYSTEM
orientated, with the threaded holes located as shown. Pins may be factory
fitted, or fitted on site prior to installation, at the fabricators discretion.
2. Install curtain walling grid in accordance with the recommendations of the System 17 curtain walling
manual.
3. Check the line and level of the brise soleil brackets to ensure they run through at the correct height
relative to the setting out datum. Adjust grid accordingly if required.
4. For silicone pointed mullions continue the curtain walling installation in accordance with the System
17 Latitude/SP manuals, up to and including gaskets and glazing. Continue silicone pointing between
glass units over brise soleil brackets and both sides of projecting nose. HR50121 push-in gasket is
not suitable for use with brise soleil brackets.
5. For pressure plate and cover cap applications push thermal isolator into nose of mullion, butting up
against bracket as indicated.
a. Continue the curtain walling installation in accordance with the System 17 manual, up to and
including gaskets, glazing and pressure plates ensuring that the brise soleil bracket protrudes
through the pre-prepped slot in the pressure plate. Ensure that standard pressure plate fixings
adjacent to brise soleil brackets are within 300mm of the brise soleil stitch plate fixings.
b. Using a low-modulus silicone sealant, fill and seal all voids between the projecting nose of the
brise soleil brackets and the slots in the pressure plate.
c. Position brise soleil stitch plates centrally over projecting nose of brise soleil brackets. See also
"Brise Soleil Stitch Plate Application" sheet.
d. Apply CW09 cover caps to curtain wall screen ensuring nose of brise soleil bracket protrudes through
pre-prepped slot in cover cap, and seal.
6. Fit the 1 No BS77 grub screw into the threaded hole in the brise soleil bracket (as shown in Diagram
1) ensuring that the screw is projecting equally on each side.
7. Locate brise soleil panel between adjacent brise soleil brackets, and lower into position hooking slot
over grub screw as shown (Diagram 4).
8. Temporarily hold in position by inserting BS47 bracket fixing bolts through the dead holes of
upriggers and brackets. When installing a horizontal row of panels ensure fixing bolts do not project
beyond brackets hindering installation of adjacent panel. Once adjacent panel has been located
ensure BS47 bolt is then pushed fully through to secure both panels.
9. Secure panels in position with BS48 nyloc nuts (Diagram 5). Brise soleil panels must not be left
unattended without bolting permanently into position.
10. Repeat procedure along length of brise soleil screen.
11. Check line and level of brise soleil panels and finally tighten all BS47 / BS48 fixings.
Diagram 1
Diagram 2
Thermal
isolator
Curtain
walling
mullion
Brise soleil
bracket
Fit BS77
grub screw
Diagram 3
BS80
Bracket pin
Threaded
hole
Thermal
isolator
Diagram 4
Diagram 5
BS47 Bracket fixing bolt
with BS48 nyloc nut
Not to scale
C
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 1
22 / 5 / 60
10/12/10
Structural Chart for Brise Soleil
Blades
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
The following chart is for guidance purposes and may be used to estimate the
structural capabilities of the System 22 Brise Soleil blades in both horizontal and vertical applications. It
must be noted however that the brise soleil will impose loads on the curtain walling mullion and its fixings
to the building structure, which must be determined by a structural engineer and catered for when
selecting the appropriate curtain walling profiles and structural fixings. All structural calculations must be
checked and confirmed by a structural engineer.
Brise soleil blade assessment procedure:
1. Determine "Site wind load" in accordance with BS 6399.
2. Establish optimum brise soleil bracket centres. For curtain walling applications these may be
determined by the mullion centres. Where practical, it may be beneficial to span over multiple mullion
centres. i.e. - Where a curtain walling grid is at 1 metre centres it may be possible to fix brise soleil
brackets at 3 metre centres. This will however be subject to the spanning capabilities of the blade.
3. Select the appropriate brise soleil blade using the following chart: Using the desired brise soleil bracket
fixing centres, establish the blade length. The intersection of the "Blade length" with the "Site wind
load" must fall below the plotted curve of the permissible blade(s). i.e. - Where the intersection falls
above a curve, conditions exceed the structural capabilities of that blade/blades. In such circumstances,
reduce bracket fixing centres/blade length, and re-assess using chart.
Blade deflection limitation = ±Span/100
2400
2200
Site wind load (Pa)
2000
1800
15
0m
m
1600
1400
20
0m
m
bl
ad
e
bl
ad
e
1200
1000
800
600
Not to Scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
Blade length (mm)
SHEET
rev 2
22 / 6 / 10
10/12/10
4000
3900
3800
3700
3600
3500
3400
3300
3200
3100
3000
2900
2800
2700
2600
2500
2400
2300
2200
400
Brise Soleil Structural Assessment
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
The following charts are for guidance purposes and may be used to estimate the structural capabilities of
cantilevered horizontal brise soleil manufactured using the standard Metal Technology brise soleil
components, fabricated and installed in accordance with the recommendations and details set out in the
System 22 Brise Soleil manual. The design of the brise soleil system takes into consideration the
structural capabilities of the blades, the brackets, the outriggers/upriggers, their fixings, and their
attachment to the curtain walling mullion. The following charts do not take into consideration the effect
the Brise Soleil has on the curtain walling mullions, or the fixings required to secure the wall-mounted
T-brackets to the structure, which must be determined by a structural engineer. All structural calculations
must be checked and confirmed by a qualified structural engineer.
Cantilevered brise soleil assessment procedure:
1. Determine "Site wind load" in accordance with BS 6399.
2. Establish the brise soleil "span" i.e. - From centre line of fixing bracket to centre line of fixing bracket.
For curtain walling applications this is determined by the mullion centres. Where practical it may be
beneficial to span over multiple mullion centres. i.e. - Where a curtain walling grid is at 1 metre
centres it may be possible to fix the brise soleil brackets at 3 metre centres, resulting in a 3 metre
span.
3. Determine desired projection of brise soleil and using the "Component Identification" sheet select
appropriate outrigger to suit.
4. Using the following charts read horizontally from the "Site wind load" axis and vertically from the
"Cantilevered projection" axis and provided the intersection is below the applicable span curve, the
brise soleil design is satisfactory. i.e. - where the intersection falls above the applicable span curve,
conditions exceed the structural capabilities of the brise soleil assembly. In such circumstances
re-assess using a larger blade if possible, or reduce the bracket fixing centres/span, and/or the desired
projection/outrigger. Alternatively the brise soleil may be propped.
SHEET
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
rev 4
22 / 6 / 20
22/07/11
Cantilevered Horizontal Brise Soleil
Structural Chart
150mm blade using curtain walling bracket BS70
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
BS98
8-blade
outrigger
BS97
7-blade
outrigger
BS96
6-blade
outrigger
BS95
5-blade
outrigger
BS94
4-blade
outrigger
BS93
3-blade
outrigger
BS92
2-blade
outrigger
This chart is for quidance only. All structural calculations must be checked and
confirmed by a structural engineer.
2400
pan
ms
0m
pan
100
ms
0m
pan
120
ms
0m
n
140
spa
m
00m
pan
s
16
m
0m
n
spa
180
m
0m
m
0m
n
spa
2400mm span
2000
200
220
2200
Site wind load (Pa)
1800
2600mm span
1600
1400
2800mm span
1200
3000mm span
1000
800
600
4000mm span
400
200
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
0
Cantilevered projection
Cantilevered projection for curtain walling applications = Outrigger length + 26.5mm
Not to Scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 4
22 / 6 / 30
07/07/11
Cantilevered Horizontal Brise Soleil
Structural Chart
System 22
200mm blade using curtain walling bracket BS71
ALUMINIUM BRISE
SOLEIL SYSTEM
BS107
7-blade
outrigger
BS106
6-blade
outrigger
BS105
5-blade
outrigger
BS104
4-blade
outrigger
BS103
3-blade
outrigger
BS102
2-blade
outrigger
This chart is for quidance only. All structural calculations must be checked and
confirmed by a structural engineer.
2400
n
spa
m
n
00m
10
spa
mm
n
00
12
spa
mm
n
00
14
spa
mm
n
00
16
spa
mm
n
00
spa
18
m
0m
an
p
200
ms n
0m
a
220 m sp
0m
an
240
sp
m
m
00
26
2200
2000
2800mm span
Site wind load (Pa)
1800
1600
3000mm span
1400
1200
1000
4000mm span
800
600
400
200
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
0
Cantilevered projection
Cantilevered projection for curtain walling applications = Outrigger length + 26.5mm
Not to Scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 5
22 / 6 / 40
07/07/11
Cantilevered Horizontal Brise Soleil
Structural Chart
150mm blade using wall mounted "T" bracket BS87
System 22
ALUMINIUM BRISE
SOLEIL SYSTEM
BS98
8-blade
outrigger
BS97
7-blade
outrigger
BS96
6-blade
outrigger
BS95
5-blade
outrigger
BS94
4-blade
outrigger
BS93
3-blade
outrigger
BS92
2-blade
outrigger
This chart is for quidance only. All structural calculations must be checked and
confirmed by a structural engineer.
2400
an
sp
m
m
00
10
an
sp
mm
00
an
12
sp
mm
n
00
spa
14
mm an
00
sp
16
mm an
00
sp
18
mm span
00
20 m m
00
22
2200
2400mm span
2000
Site wind load (Pa)
1800
2600mm span
1600
1400
2800mm span
1200
3000mm span
1000
800
3500mm span
600
4000mm span
400
200
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
0
Cantilevered projection
Cantilevered projection for wall mounted applications = Outrigger length + 48.5mm
Not to Scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 0
22 / 6 / 50
07/07/11
Cantilevered Horizontal Brise Soleil
Structural Chart
System 22
200mm blade using wall mounted "T" bracket BS88
ALUMINIUM BRISE
SOLEIL SYSTEM
BS107
7-blade
outrigger
BS106
6-blade
outrigger
BS105
5-blade
outrigger
BS104
4-blade
outrigger
BS103
3-blade
outrigger
BS102
2-blade
outrigger
This chart is for quidance only. All structural calculations must be checked and
confirmed by a structural engineer.
2400
an
sp
m
m
00
10
an
sp
mm
00
an
12
sp
mm
00
an
14
sp
mm
an
00
sp
16
m m an
00
sp
18
m m pan
s
00
2 0 mm pan
s
00
22 mm pan
s
00
24 0mm
0
26
2200
2000
2800mm span
Site wind load (Pa)
1800
1600
3000mm span
1400
1200
3500mm span
1000
4000mm span
800
600
400
200
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
0
Cantilevered projection
Cantilevered projection for wall mounted applications = Outrigger length + 48.5mm
Not to Scale
METAL TECHNOLOGY LIMITED . This data sheet is issued subject to the condition that
it shall not be reproduced without the consent of Metal Technology in writing. 06/07
SHEET
rev 0
22 / 6 / 60
07/07/11
System 22 Brise Soleil
APPENDIX
Section 0: Specification, Profile Index and Component ID
22/0/10 rev 3
Specification
22/0/20 rev 1
Profile Index
22/0/30 rev 4
Component Identification
22/0/40 rev 5
Component Identification
22/0/50 rev 4
Component Identification
22/0/60 rev 2
Component Identification
22/0/70 rev 1
Component Identification
22/0/80 rev 1
Component Identification
22/0/90 rev 0
Component Identification
Section 1: Section Drawings
22/1/10 rev 1
Section Drawings
Section 2: General Arrangement Drawings
22/2/10 rev 2
General Arrangement - Cantilevered Panels
22/2/20 rev 3
General Arrangement - Vertical Panels
22/2/30 rev 3
General Arrangement - Curtain Walling Assembly Detail
22/2/40 rev 5
General Arrangement - Brise Soleil Cantilevered off Curtain Walling
22/2/50 rev 4
General Arrangement - Brise Soleil Cantilevered off Structure
22/2/60 rev 4
General Arrangement - Brise Soleil Propped off Curtain Walling
22/2/70 rev 4
General Arrangement - Brise Soleil Propped off Structure
22/2/80 rev 3
General Arrangement - Horizontal Bracket Details
22/2/90 rev 2
General Arrangement - Horizontal Bracket Details
22/2/100 rev 2
General Arrangement - Vertical Brise Soleil off Curtain Walling
22/2/110 rev 2
General Arrangement - Vertical Brise Soleil off Structure
22/2/120 rev 2
General Arrangement - Vertical Bracket Details
22/2/130 rev 2
General Arrangement - Vertical Bracket Details
Section 3: Ironmongery Requirements
22/3/10 rev 2
General Notes
22/3/20 rev 1
General Notes
Issue Date: 04/08/11
22/3/30 rev 1
General Notes
22/3/40 rev 1
General Notes
Section 4: Fabrication Details
22/4/10 rev 4
Fabrication Sizes - Horizontal Brise Soleil
22/4/20 rev 3
Mullion Prep for Horizontal Brise Soleil Brackets
22/4/30 rev 3
Upper Prop Bracket Setting-out Detail off Curtain Walling
22/4/40 rev 2
Mullion Prep for BS57 Bracket
22/4/50 rev 3
Upper Prop Bracket Setting-out Detail off Structure
22/4/60 rev 3
Outrigger Prep for Lower Prop Bracket
22/4/70 rev 3
Fabrication Sizes - Vertical Brise Soleil
22/4/80 rev 3
Mullion Prep for Vertical Brise Soleil Brackets
22/4/90 rev 0
Bracket Setting-out Dimensions - 150mm Vertical Brise Soleil
22/4/100 rev 0
Bracket Setting-out Dimensions - 200mm Vertical Brise Soleil
22/4/110 rev 0
Pressure Plate and Cover Cap Preps
22/4/120 rev 0
Brise Soleil Stitch Plate Application - PVC Pressure Plate
22/4/130 rev 0
Brise Soleil Stitch Plate Application - Aluminium Pressure Plate
Section 5: Installation and Assembly
22/5/10 rev 1
Horizontal Panel Assembly Detail
22/5/20 rev 1
Vertical Panel Assembly Detail
22/5/30 rev 2
Installation / Assembly Procedure
22/5/40 rev 1
Installation / Assembly Procedure
22/5/50 rev 0
Installation / Assembly Procedure
22/5/60 rev 1
Installation / Assembly Procedure
Section 6: Structural Properties
22/6/10 rev 2
Structural Chart for Brise Soleil Blades
22/6/20 rev 4
Brise Soleil Structural Assessment
22/6/30 rev 4
Cantilevered Horizontal Brise Soleil Structural Chart - 150mm blade using curtain walling bracket BS70
22/6/40 rev 5
Cantilevered Horizontal Brise Soleil Structural Chart - 200mm blade using curtain walling bracket BS71
22/6/50 rev 0
Cantilevered Horizontal Brise Soleil Structural Chart - 150mm blade using wall mounted "T" bracket BS87
22/6/60 rev 0
Cantilevered Horizontal Brise Soleil Structural Chart - 200mm blade using wall mounted "T" bracket BS88
Issue Date: 04/08/11