Brooks Automation Inc. Polycold Systems

Brooks Automation, Inc.
15 Elizabeth Drive
Chelmsford, MA 01824 U.S.A
Tel 978-262-2400
Fax 978-262-2500
www.brooks.com
Brooks Automation Inc.
Polycold Systems
Customer Instruction Manual
®
POLYCOLD GAS CHILLERS
Models:
PGC-152 AC
PGC-152 WC
PGC-152 AC w/ Flow Control Unit
PGC-152 WC w/ Flow Control Unit
PGC-152 AC CE Back Line Layout
PGC-152 AC CE/S2 M/OP
PGC-152 WC CE/S2 M/OP
825101-00 (Rev C)
700179-01
700179-02
700179-03
700179-04
700179-05
700179-06
700179-07
This page intentionally left blank
825101-00 (Rev C)
Safety Information
PGC Manual
Brooks Automation, Inc.
Polycold Systems
15 Elizabeth Drive
Chelmsford, MA 01824
U.S.A.
Tel: 978-262-2400
Fax: 978-262-2500
Service:
Contact Brooks Automation at http://www.brooks.com or the 24 hour emergency number: for the nearest
service representative.
North America
1 800-FOR-GUTS (800-367-4887)
Germany
France
UK
+49 1804-CALL-GUTS (1804-2255-4887)
Japan
+81-3-5767-3412
China
+86-21-5131-7066
Taiwan
+886-3-5525225
Korea
+82-31-288-2500
Singapore
+65-6464-1481
Before starting:
®
®
Congratulations for purchasing a Brooks Automation Inc. Polycold Systems Cool Solutions Gas Chiller. If
any assistance is needed, please contact a local sales representative or Brooks Automation Inc.
To contact Brooks Automation Inc. by:
Telephone:
978-262-2400
Toll Free:
(1) (800) FOR GUTS (800-367-4887) “within USA only”
Fax
978-262-2500
Mail:
Brooks Automation, Inc. 15 Elizabeth Drive, Chelmsford, MA 01824 U.S.A
Website:
www.brooks.com
Please have the following information available to help us expedite the service
process:
®
Polycold Model: __________________________
®
Polycold Serial No: ________________________
®
Polycold Item Code: _______________________
Date Manufactured: ________________________
The above information is on the nameplate of the Gas Chiller. It is best to enter this information now
(before the equipment is installed).
825101-00 (Rev C)
Page i
Safety Information
PGC Manual
© 2010 by Brooks Automation Inc.
Polycold Systems
All rights reserved.
Printed in the United States of America.
Trademark Recognition:
Armaflex® is a registered trademark of Armstrong World Industries, Inc.
CPI UltraSeal™ is a trademark of Parker Hannifin Corporation.
Phillips® is a registered trademark of Phillips Screw Company.
Polycold® is a registered trademark of Brooks Automation Inc.
VCR® is a registered trademark of Cajon Company.
is a registered trademark of Brooks Automation Inc.
825101-00 (Rev C)
Page ii
Safety Information
PGC Manual
Polycold® Systems Cooling Products, CryoTiger®, AquaTrap®, Polycold Compact Cooler, Repair Services and Certified
Refurbished Products
Polycold® Systems cryogenic cooling products, including water vapor cryopumps (PFC, PCT, FLC, FI), chillers (PGC, PGCL),
cryocoolers (P), CryoTiger, AquaTrap, Polycold Compact Cooler (PCC) and accessories, Certified Refurbished products (the
“Products”) and Repair Service (i.e.- repairs other than warranty repairs) are warranted to be free from defects in materials
and/or workmanship under normal service for the time period as set forth in Table A below from date of shipment from Brooks
Automation, Inc. (“Brooks”). The warranty for Repair Service and Products is limited to the component parts replaced or repair
performed by Brooks at Brooks’ facility. Customer is responsible for all charges and expenses for Brooks Services provided at
Customer’s location by Brooks technicians as set forth in a quotation. Certified Refurbished Products and warranty exchange
Products are remanufactured to like-new condition and contain used parts and materials.
Table A
Product
New Product
Warranty
Repair Service
Warranty
Certified Refurbished
Cryogenic Cooling Products Warranty
Cryotiger® Products and Systems
AquaTrap® Products and Systems
Polycold® Compact Cooler (PCC)
15 Months
12 Months
N/A
Cryogenic cooling products, including:
Water vapor cryopumps (PFC, PCT, FLC,
FI), chillers (PGC, PGCL), cryocoolers (P),
and accessories
24 Months
12 Months
12 months
BROOKS MAKES NO OTHER REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO PRODUCTS OR
SERVICES. UNLESS EXPRESSLY IDENTIFIED AS A WARRANTY, SPECIFICATIONS IN ANY PRODUCT DATASHEET CONSTITUTE
PERFORMANCE GOALS ONLY, AND NOT WARRANTIES. BROOKS MAKES NO WARRANTY RESPECTING THE MERCHANTABILITY OF
PRODUCTS OR THEIR SUITABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR RESPECTING INFRINGEMENT OF
INTELLECTUAL PROPERTY RIGHTS. BROOKS DISCLAIMS ANY WARRANTY WITH RESPECT TO PRODUCTS MODIFIED WITHOUT
BROOKS’ WRITTEN CONSENT, REPAIRS MADE OUTSIDE OF OUR FACTORY, PRODUCTS RENDERED DEFECTIVE BY CUSTOMER
MISUSE, NEGLIGENCE, CORROSIVE ATMOSPHERES, ATTACK BY FREE CHEMICALS WITHIN THE SYSTEM, ACCIDENT, DAMAGE
BY CUSTOMER OR CUSTOMER’S AGENT, OPERATION CONTRARY TO OUR RECOMMENDATION, IF THE SERIAL NUMBER HAS
BEEN ALTERED, DEFACED OR REMOVED, THE USE OF SERVICE REPLACEMENT REFRIGERANTS FROM ANY THIRD PARTY NOT
LICENSED BY BROOKS, OR THE PRODUCT IS OTHERWISE COMPROMISED BY USE OF UNAUTHORIZED PARTS OR SERVICE, ALL
AS DETERMINED BY BROOKS IN ITS SOLE DISCRETION.
IN NO EVENT WILL CUSTOMER BE ENTITLED TO, NOR WILL BROOKS BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION NEGLIGENCE, STRICT LIABILITY, OR
OTHERWISE, ARISING AT ANY TIME, FROM ANY CAUSE WHATSOEVER, INCLUDING, WITHOUT LIMITATION, DOWN-TIME COSTS,
DATA LOSS, DAMAGE TO ASSOCIATED EQUIPMENT, REMOVAL AND/OR REINSTALLATION COSTS, REPROCUREMENT COSTS, OR
LOST PROFITS, EVEN IF BROOKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND EVEN IF THE LIMITED
REMEDIES OF REPAIR OR REPLACEMENT FAIL OF THEIR ESSENTIAL PURPOSE. THIS WAIVER OF LIABILITY DOES NOT APPLY TO
EITHER BROOKS’ LIABILITY UNDER A STATUTE, ACT OR LAW PERTAINING TO BODILY INJURY, OR TO ANY LIABILITY INCURING
OUT OF DAMAGE TO THE BODY, HEALTH OR LIFE OF A PERSON.
The exclusive remedies for breach of warranty will be either repair or replacement of the nonconforming parts or Products during
the warranty period at the sole discretion of Brooks, shipped ExWorks (Incoterms 2000) Brooks factory. Customer’s recovery
from Brooks for any claim shall not exceed the amount paid by customer to Brooks for the Product or Service giving rise to such
claim, irrespective of the nature of the claim, whether in contract, tort, warranty, or otherwise. Customer must inspect the
Products within a reasonable time upon receipt, and must notify Brooks within 30 days of discovering a defect. Every claim on
account of defective material or workmanship shall be deemed waived unless made in writing within the warranty period
specified above. Brooks does not assume, or authorize any other person to assume, any other obligations or liabilities in
connection with the sale of the Products.
All Polycold Products are also subject to the Brooks Automation, Inc. General Terms and Conditions, Polycold®
Products, an excerpt of which is set forth above.
825101-00 (Rev C)
Page iii
Safety Information
PGC Manual
This page intentionally left blank
825101-00 (Rev C)
Page iv
Table of Contents
PGC Manual
Table of Contents
1 SAFETY INFORMATION ........................................................................................................................................... 1
2
3
1.1
1.2
1.3
1.4
1.5
Safety Hazards and Safeguards ................................................................................................................... 1
Danger, Warning, and Caution Alerts ........................................................................................................... 2
Safety Training Guidelines ............................................................................................................................ 4
Definition of Electrical Work Types ............................................................................................................... 4
Potential Hazards During Maintenance & Servicing ..................................................................................... 5
1.5.1
1.5.2
Air Cooled PGC 152 w/o Flow Control Unit ............................................................................................... 6
Water Cooled PGC 152 with Flow Control Unit .......................................................................................... 9
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
Material Safety Data Sheets ....................................................................................................................... 13
Refrigeration Compliance ........................................................................................................................... 13
Conversion Factors & Formulas ................................................................................................................. 13
Safety Devices ............................................................................................................................................ 14
Lock-Out and Tag-Out Instructions (LOTO) ............................................................................................... 15
Safety Interlocks.......................................................................................................................................... 16
Circuit Breaker Protection ........................................................................................................................... 16
Emergency Shut-Down Procedures............................................................................................................ 17
OVERVIEW ......................................................................................................................................................... 19
2.1
2.2
2.3
System Diagrams ........................................................................................................................................ 19
About the PGC ............................................................................................................................................ 21
PGC 152 Model Features ........................................................................................................................... 22
2.3.1
2.3.2
2.3.3
2.3.4
Exterior Features, Air Cooled PGC 152 w/o Flow Control Unit ................................................................ 23
Interior Features, Air Cooled PGC 152 w/o Flow Control Unit ................................................................. 24
Exterior Features, Water Cooled PGC 152 with Flow Control Unit .......................................................... 25
Interior Features, Water Cooled PGC 152 with Flow Control Unit ........................................................... 26
INSTALLATION................................................................................................................................................... 27
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
4
OPERATION ....................................................................................................................................................... 37
4.1
5
Tools and Materials Required ..................................................................................................................... 27
Inspect the PGC .......................................................................................................................................... 27
Position the PGC......................................................................................................................................... 27
Cooling Water Connection (WC Units) ....................................................................................................... 28
Connect the Gas-Outlet Thermocouple Wire to a Temperature Meter (Optional) ...................................... 29
Connect the Electrical Power ...................................................................................................................... 30
Connection of Flow Control Unit (Optional) ................................................................................................ 31
Power Interruption/Restoration ................................................................................................................... 31
PGC Remote Control System (Optional) .................................................................................................... 31
Enable Remote On/Off Operation ............................................................................................................... 32
Install the External Gas Circuit .................................................................................................................... 33
Starting the Polycold Gas Chiller ................................................................................................................ 37
INSPECTION & MAINTENANCE ....................................................................................................................... 39
5.1
5.2
5.3
Periodic Inspection ...................................................................................................................................... 39
Inspect for water condensation in the gas circuit. ....................................................................................... 39
If the unit is Air-Cooled, verify there is adequate air circulation through the condenser. ........................... 39
825101-00 (Rev C)
Page i
Table of Contents
5.4
5.5
5.6
5.7
6
PGC Manual
If the unit is Water-Cooled, verify the following: .......................................................................................... 39
Verify the insulation on the gas-out line is adequate. ................................................................................. 39
Verify the refrigerant circuit does not have a leak. ...................................................................................... 39
Remove moisture from the gas circuit. ....................................................................................................... 40
TROUBLESHOOTING ........................................................................................................................................ 41
6.1
The PGC's Compressor Does Not Start Or Run Properly .......................................................................... 41
6.1.1
6.1.2
Fan and compressor do not start (and make no noise). ............................................................................... 41
Compressor hums or starts, and then stops. ................................................................................................ 41
6.2
6.3
6.4
Gas Flow or Temperature Is Inadequate .................................................................................................... 41
PGC Makes Unusual Noises ...................................................................................................................... 41
Indicator Lamp Based Troubleshooting and Diagnostics ........................................................................... 42
7
DISCONNECTION, STORAGE, AND RESHIPMENT ........................................................................................ 47
7.1
7.2
8
Disconnection.............................................................................................................................................. 47
Packing for Reshipment or Storage ............................................................................................................ 47
APPENDIX .......................................................................................................................................................... 49
8.1
8.2
8.3
BRAZING SPECIFICATION ....................................................................................................................... 49
THERMOCOUPLE ATTACHMENT SPECIFICATION ............................................................................... 49
Specifications .............................................................................................................................................. 51
9
GLOSSARY ........................................................................................................................................................ 53
10
PROCESS & INSTRUMENTATION AND ELECTRICAL SCHEMATICS........................................................... 54
825101-00 (Rev C)
Page ii
Table of Contents
PGC Manual
List of Tables
Table 1-1: Warning Label Legend ............................................................................................................................... 2
Table 1-2: PGC Safety Devices ................................................................................................................................. 14
Table 3-1: Cooling Water Flow/Temperature Requirements ..................................................................................... 29
Table 3-2: Electrical Requirements ............................................................................................................................ 31
Table 8-1: General Specifications .............................................................................................................................. 51
List of Illustrations
Figure 1-1: Typical Warning Labels ............................................................................................................................. 3
Figure 1-2: Hazard Labels, Exterior Side Panels, Air-Cooled PGC 152 ..................................................................... 6
Figure 1-3: Hazard Labels, Front, Left, & Top Sides, Air-Cooled PGC 152 ................................................................ 7
Figure 1-4: Hazard Labels, Rear & Left Sides, Air-Cooled PGC 152 .......................................................................... 8
Figure 1-5: Hazard Labels, Exterior Side Panels, Water-Cooled PGC 152 ................................................................ 9
Figure 1-6: Hazard Labels, Lower Front & Right Sides, Water-Cooled PGC 152 ..................................................... 10
Figure 1-7: Hazard Labels, Lower Rear & Left Sides, Water-Cooled PGC 152 ........................................................ 11
Figure 1-8: Caution Label, PGC 152 Optional Flow Control Unit .............................................................................. 12
Figure 1-9: Run & Start Capacitors ............................................................................................................................ 16
Figure 2-1: System Block Diagram ............................................................................................................................ 19
Figure 2-2: Electrical Distribution Diagram ................................................................................................................ 20
Figure 2-3: System Dimensions ................................................................................................................................. 21
Figure 2-4: Air Cooled PGC 152 w/o Flow Control (Ext. Panels Installed) ................................................................ 23
Figure 2-5: Air Cooled PGC 152 w/o Flow Control (Ext. Panels Removed) .............................................................. 24
Figure 2-6: Water Cooled PGC 152 w/ Flow Control (Ext. Panels Installed) ............................................................ 25
Figure 2-7: Water Cooled PGC 152 w/ Flow Control (Ext. Panels Removed) .......................................................... 26
Figure 3-2: Remote Bypass Jumper .......................................................................................................................... 32
Figure 3-3: Optional Flow Control Gas Inlet & Outlet ................................................................................................ 34
Figure 3-4: PGC Gas Inlet & Outlet ........................................................................................................................... 35
Figure 3-5: PGC-152 Typical Capacity (Flow Rate vs. Gas-Outlet Temperature) .................................................... 36
Figure 10-1: Process & Instrumentation Diagram, PGC-152 W/CE/S2 .................................................................... 55
Figure 10-2: Process & Instrumentation Diagram, PGC-152 CE/S2 W/ Flow Control .............................................. 56
Figure 10-3: Circuit Diagram, PGC-152 CE W/RMT IEC ........................................................................................... 57
Figure 10-4: Circuit Diagram, PGC-152 CE/S2 Flow Control Option ........................................................................ 58
825101-00 (Rev C)
Page iii
Safety Information
PGC Manual
1 SAFETY INFORMATION
1.1
Safety Hazards and Safeguards
This chapter summarizes safety concerns (hazards, precautions, and ergonomics) associated with the
®
operation and service of Polycold’s Cool Solutions Gas Chillers.
The Gas Chillers have been designed to conform to all known safety requirements applicable to Brooks
Automation Inc. wafer fab equipment. Under normal operation the direct refrigeration and heating
equipment presents no hazard to its operator or other personnel. Tool secured access panels shield
operators and other personnel working in the area of the equipment from the operation or possible
failure of the components that compose the equipment.
Only qualified service personnel are authorized to open or remove the panels and must be in
accordance with the safety instructions presented in this chapter and throughout the manual. In service
and repair operations, the direct refrigeration and heating equipment may potentially expose personnel
to the following hazards:

Electrical Shock

Hazardous Materials

Lifting Hazards

Cold Surfaces

Hot Surfaces
The information and instructions provided in this chapter and throughout this manual are intended to
help service personnel work with the equipment in a safe, effective, and efficient manner. The
emergency and safety procedures are provided to help service personnel develop safe practices and
®
establish safe conditions for working with Polycold’s Cool Solutions Gas Chillers.
825101-00 (Rev C)
Page 1
Safety Information
1.2
PGC Manual
Danger, Warning, and Caution Alerts
Danger, Warning, and Caution alerts are integral parts of these instructions:

DANGER is used to indicate an imminently hazardous situation that, if not avoided, will result in
death or serious injury.

WARNING is used to indicate a potentially hazardous situation that, if not avoided, could result in
death or serious injury.

CAUTION is used to indicate a potentially hazardous situation that, if not avoided, may result in
minor or moderate injury.

CAUTION is also used when failure to follow instructions or precautions can result in damage to the
equipment.
Danger, Warning, and Caution alerts must be read carefully, understood thoroughly, and observed at all
times. If this equipment is used in a manner not specified by the manufacturer, the protection provided
by the equipment may be impaired. Pictorial hazard alerts affixed to the direct refrigeration and heating
equipment and its components are in accordance with ANSI, FDA, SEMI, and (where applicable) IEC
standards. Pictorial hazard alerts follow the format described below:
Hazard Keyword Level
Pictogram (icon)
depicting nature
of hazard
Text describing
hazard and what might
/ could happen
Text describing how to
avoid the hazard
‡
`
SAFETY ALERT SYMBOL
DANGER - White Lettering / Red Background
(Safety Red: per ANSI Z535.4 - 15 parts Warm Red,
1 part Rubine Red, 1/4 part Black)
White Triangle / Red Exclamation Point
WARNING - Black Lettering / Orange Background
(Safety Orange: per ANSI Z535.4 - 13 parts Yellow, 3
parts Warm Red, 1/4 part Black)
Black Triangle / Orange Exclamation Point
CAUTION - Black Lettering / Yellow Background
(Safety Yellow: per ANSI Z535.4 - Pantone 108C)
Black Triangle / Yellow Exclamation Point
Table 1-1: Warning Label Legend
825101-00 (Rev C)
Page 2
Safety Information
PGC Manual
This page includes pictogram representations used on semiconductor manufacturing equipment. Some
®
of these pictograms will be found on Polycold’s Cool Solutions Gas Chiller equipment. Actual label
configurations and placement will be found in this chapter. Please note, for purposes of clarity, most
illustrations depicting hazardous exposures show components in their most hazardous state (i.e., covers
removed, safety interlocks, and other safeguards defeated) as they might appear during a major service
activity. Most tasks do not require that the hazards be exposed to this degree.
Figure 1-1: Typical Warning Labels
825101-00 (Rev C)
Page 3
Safety Information
1.3
PGC Manual
Safety Training Guidelines
The safety information in this chapter is a summary of the safety information that is to be successfully
®
conveyed to service personnel as part of their training on Polycold’s Cool Solutions Gas Chillers. The
training program is intended to ensure that any person who undertakes the service of the Gas Chiller
can demonstrate competence to perform the required tasks safely. Accordingly, training required for
each task includes, but is not limited to, the following:

A review of applicable safety standards and procedures, such as those presented in this chapter.

A review of maintenance and safety recommendations applicable to vendor supplied equipment.

An explanation of the purpose of a subsystem and its operation.

An explanation of the specific tasks and responsibilities of each person (operator, service personnel,
etc.) assigned to the Gas Chillers equipment.

The person(s) (identified by name, location, and telephone number) to be contacted when required
actions are beyond the training and responsibility of the person being trained.

Identification of the recognized hazards associated with each task.

Identification of, and appropriate responses to, unusual operating conditions.

Explanation of the functions and limitations of all safeguards and their design characteristics.

Instructions for the functional testing (or other means of assurance) for proper operation of
safeguarding devices.
Safe use and service of the Gas Chiller equipment also requires the following:
1.4

Service personnel should understand the operation of process-related hardware interlocks, and the
sequences of hardware operation that are executed automatically, as explained in this chapter.

The equipment should not be used without assuring correct operation of all connected facilities,
especially fugitive emissions exhaust.

Service personnel should always assume that high voltage is present unless they have personally
turned it off and locked it out.

The equipment should not be operated without all guards and safety devices in place.

The equipment should be shutdown, locked-out, and not be operated while it is being maintained.

Users should not attempt to defeat, modify, or disable any of the equipment's safety interlock
switches.

Only Brooks Automation Inc. trained service personnel should perform installation, assembly,
operation, disassembly, service, or maintenance of the PGC.

All safety related incidents or near misses should be reported to a supervisor or to Brooks
Automation Inc.

The user should carefully review and understand manufacturer provided material
safety data sheets (MSDS) for materials used by this equipment.
Definition of Electrical Work Types
The following are the four types of electrical work in SEMI S2-0200:
Type 1- Equipment is fully deenergized.
Type 2- Equipment is energized. Energized circuits are covered or protected.
Note: Type 2 work includes tasks where the energized circuits are or can be measured by placing
probes through suitable openings in the covers or insulators.
825101-00 (Rev C)
Page 4
Safety Information
PGC Manual
Type 3- Equipment is energized. Energized circuits are exposed and inadvertent contact with
uninsulated energized parts is possible. Potential exposures are no greater than 30 volts rms, 42.4 volts
peak, 60 volts dc or 240 volt-amps in dry locations.
Type 4- Equipment is energized. Energized circuits are exposed and inadvertent contact with
uninsulated energized parts is possible. Potential exposures are greater than 30 volts rms, 42.4 volts
peak, 60 volts dc or 240 volt-amps in dry locations. Potential exposures to radio-frequency currents
exist; refer to SEMI S2-0200, Table A5-1 of Appendix 5 for a listing of these values.
1.5
Potential Hazards During Maintenance & Servicing
This section illustrates the placement of labels on both air & water-cooled versions of the PGC (and flow
control option) that identify the location and type of potential hazards that may be encountered within the
unit. Some labels identifying other notable features are also depicted.
For brevity, only (2) of (4) model configurations are illustrated. An air-cooled gas chiller without a flow
control unit, and a water-cooled gas chiller with a flow control unit are shown, however both air and
water-cooled models can be configured with or without the optional flow control unit. Selection of the
optional flow control unit only affects one hazard label. Models configured with a flow control unit are
rated for a maximum gas supply pressure of 100 psi. Models without the flow control unit are rated for a
maximum gas supply pressure of 400 psi.
825101-00 (Rev C)
Page 5
Safety Information
PGC Manual
1.5.1 Air Cooled PGC 152 w/o Flow Control Unit
The figure below shows an Air-Cooled PGC 152 with all exterior panels installed. The (3) hazard labels
shown below are affixed to all (4) exterior side panels.
Front & Right Sides
Rear & Left Sides
Figure 1-2: Hazard Labels, Exterior Side Panels, Air-Cooled PGC 152
825101-00 (Rev C)
Page 6
Safety Information
PGC Manual
The figure below shows the front and right sides of an Air-Cooled PGC 152 with the exterior side panels
removed. The caution label on top of the unit specifies the gas types and the maximum gas supply
pressure that can be connected to the gas inlet tube. The hazardous voltage warning label is affixed to
the units’ electrical enclosure.
The maximum 400 psi (2760 kPa)
rating shown, only applies when
connecting directly to the PGC. When
connecting to the optional Flow Control
Unit, the maximum rating is 100 psi
(690 kPa).
Figure 1-3: Hazard Labels, Front, Left, & Top Sides, Air-Cooled PGC 152
825101-00 (Rev C)
Page 7
Safety Information
PGC Manual
The figure below shows the rear and left sides of an Air-Cooled PGC 152 with the exterior side panels
removed. These warning labels are affixed to the Primary Expansion Tank and the Compressor.
PRIMARY REFRIGERANT
EXPANSION TANK
407020 REV 01
XQS23689
Figure 1-4: Hazard Labels, Rear & Left Sides, Air-Cooled PGC 152
825101-00 (Rev C)
Page 8
Safety Information
PGC Manual
1.5.2 Water Cooled PGC 152 with Flow Control Unit
The figure below shows a Water-Cooled PGC 152 with all exterior panels installed. (Shown with
Optional Flow Control Unit installed.) The (3) hazard labels shown below are affixed to all (4) exterior
side panels.
Front & Right Sides
Rear & Right Sides
Figure 1-5: Hazard Labels, Exterior Side Panels, Water-Cooled PGC 152
825101-00 (Rev C)
Page 9
Safety Information
PGC Manual
The figure below shows the lower front and right sides of a Water-Cooled PGC 152 with the exterior side
panels removed. The hazardous voltage warning label is affixed to the units’ electrical enclosure.
Figure 1-6: Hazard Labels, Lower Front & Right Sides, Water-Cooled PGC 152
825101-00 (Rev C)
Page 10
Safety Information
PGC Manual
The figure below shows the lower rear and left sides of a Water-Cooled PGC 152 with the exterior side
panels removed. These warning labels are affixed to the Primary Expansion Tank and the Compressor.
PRIMARY REFRIGERANT
EXPANSION TANK
407020 REV 01
XQS23689
Figure 1-7: Hazard Labels, Lower Rear & Left Sides, Water-Cooled PGC 152
825101-00 (Rev C)
Page 11
Safety Information
PGC Manual
The caution label on top of the Optional Flow Control Unit specifies the gas types and the maximum gas
supply pressure that can be connected to the inlet tube of the Flow Control Unit.
The maximum 100 psi (690 kPa)
rating shown, only applies when
connecting to the optional Flow
Control Unit. When connecting
directly to the PGC , (See figure
1.3) the maximum rating is 400 psi
(2760 kPa).
Figure 1-8: Caution Label, PGC 152 Optional Flow Control Unit
825101-00 (Rev C)
Page 12
Safety Information
1.6
PGC Manual
Material Safety Data Sheets
The user is advised to retain current copies of material safety data sheets (MSDS) for refrigerants and
cleaning agents used in the operation and maintenance of this equipment. One copy of the MSDS for
the system refrigerant has been attached to this users manual.
1.7
Refrigeration Compliance
The PGC 152 is free of HCFC refrigerants in accordance with the Montreal Protocol and the European
law banning HCFC refrigerants EC 2037/2000.
1.8
Conversion Factors & Formulas
1 psig = 0.07 bar = 0.07 kg/cm5
°F = (9/5 x °C) + 32
1 inch = 2.54 centimeters, exactly
C = 5/9 x (°F -32)
1 pound = 0.45 kilograms
1 standard cubic foot per hour (SCFH) = 0.47 standard liters/minute
825101-00 (Rev C)
Page 13
Safety Information
1.9
PGC Manual
Safety Devices
Safety Devices incorporated in the PGC and their functions are described below:
Descriptor
Name
Function
MCB1
Main Circuit Breaker
The Main Circuit Breaker provides overcurrent and short
circuit protection for the PGC. In the event of an
overcurrent/short circuit the contacts of the Main Circuit
Breaker separate, removing power from conductors and
components downstream of the breaker. Host equipment
should provide a circuit breaker with 10,000 ampere interrupt
capacity (AIC).
OL1
Thermal Overload
Protector
The Thermal Overload Protector is coupled to the hermetic
compressor in the area of the motor windings. In the event of
excess temperature at the motor, the thermal switch opens
removing power from the compressor. This switch is
configured for auto reset.
FP1
Fusible Plug
A fusible plug is installed in the discharge plumbing of the
compressor and serves as the controlled release point for
refrigerant should a fire occur in the area of the PGC. The
fusible plug provides a means to reduce high pressures
caused by excessive ambient temperatures in a manner
which does not result in an explosion.
HPS
High Pressure
Switch
A high pressure switch is incorporated in the discharge side
of the compressor. The switch opens contacts if the
refrigerant pressure exceeds normal operating pressure,
interrupting power to the compressor and turning it off. This
switch requires manual reset. It should not be adjusted by
the user.
HTS
High Temperature
Switch
A high temperature switch is coupled to the condenser liquid
side. In the event that the condenser is obstructed or air or
water flow is otherwise interrupted (including fan failure), the
liquid temperature will rise, opening the contacts on the high
temperature switch. This removes power from the
compressor and fan (where applicable). This switch requires
manual reset. It should not be adjusted by the user.
Table 1-2: PGC Safety Devices
Safety devices are identified in the P& ID and Circuit diagrams in Section 10.
825101-00 (Rev C)
Page 14
Safety Information
PGC Manual
Caution!
Safety devices are installed on the PGC to help protect it from permanent damage. If a protective
device is triggered, the cause of the problem must be corrected before continuing to use the PGC.
Please see "Trouble-Shooting" section or call the Brooks Automation Inc. Service Department for
assistance. Bypassing or repeated resetting of a protective device may expose personnel and or
the facility to hazards, permanently damage the equipment, and may void your warranty.
1.10 Lock-Out and Tag-Out Instructions (LOTO)
WARNING
ELECTRICAL HAZARD
Contact could cause electric shock and result in death or serious injury.
After performing LOTO of the Power Disconnect Switch, Line Voltage is still
present at input terminals of the Power Disconnect Switch. To remove electrical
power to the input terminals of the Power Disconnect Switch, refer to end-user’s
Facility Power LOTO instructions.
Electrical Lock Out and Tag Out

Notify personnel you are performing a Lock-Out Tag Out (LOTO).

Shut down system following normal procedure: Turn the PGC-152 power switch to the OFF position.
Verify that the compressor is off and the indicator lights Power and Run are OFF.

Isolate the system from the electrical supply by opening the customer supplied disconnect switch or
unplugging the unit from the power receptacle. Verify that the Line indicator light is not lit.

Prevent re-connection of the electrical supply to the unit by applying a suitable lock-out device (not
supplied) to the customer switch or the disconnected plug. Attach a tag stating: “This equipment is
locked out. Do not operate.” to the switch or plug. Write your name and phone number on the tag.

Verify the system is locked-out. Observe that all indicator lights are OFF, turn the PGC-152 power
switch to ON and verify that the compressor does not start and all indicator lights remain off. Then
turn the PGC-152 power switch to OFF.
825101-00 (Rev C)
Page 15
Safety Information

PGC Manual
It may be necessary to discharge the capacitors directly by connecting a 10KΩ resister from each
capacitor terminal to ground. A qualified and trained technician must perform this procedure. The
capacitors are located inside the electrical enclosure. See figure below.
Run & Start
Capacitors
Figure 1-9: Run & Start Capacitors

Use a voltmeter to verify “0” volts in the area you will be working. Service can now be performed.

To reenergize, reverse first 4 steps.
Gas Supply Lock Out and Tag Out

Notify personnel you are performing a Lock-Out Tag Out (LOTO)

Isolate the system from the gas supply by closing the customer supplied gas shutoff valve.

Lock the customer shutoff valve in the off position using a lockout device (not supplied) and place a
tag, which states “This equipment is locked out”, and include your name, and “Do not operate.”

Verify the system is locked-out by cracking the gas inlet fitting on the PGC unit and allow the
pressure to bleed down for 2 minutes—the flow should gradually slow to a stop.

To re-establish gas supply, reverse first 3 steps.
1.11 Safety Interlocks
The PGC safety interlock circuitry design is a positive logic, hardware based, fault tolerant device
(approved by an authorized testing agency and NRTL approved for use as a safety device), providing
operator notification, requiring manual reset, and which places the equipment in a safe standby
condition upon activation.
1.12 Circuit Breaker Protection
Over Current Protection is provided by the Main Circuit Breaker (MCB1) located on the PGC 152’s Front
Panel. (MCB1 is labeled “Power”.) The rating voltage and amperage for MCB1 are 230V and 20A.
Note: Units built prior to April 11, 2005 are equipped with a 16A circuit breaker.
825101-00 (Rev C)
Page 16
Safety Information
PGC Manual
1.13 Emergency Shut-Down Procedures
Refrigerant Leak
WARNING
CHEMICAL HAZARD
Do not release refrigerant to the atmosphere. Opening the refrigerant circuit or
changing valve settings along with the failure to following instructions in this manual
could result in death or serious injury.
Review this manual before performing any procedure including routine operation of
®
Polycold’s Cool Solutions Gas Chillers. Do not release refrigerant to the
atmosphere.

For all leaks: Follow the instructions in the Material Safety Data Sheets.
Electrical Problem
WARNING
ELECTRICAL
Failure to have a qualified electrician do all electrical work could result in death or
serious injury.
Do not reach inside the refrigeration unit. A qualified electrician must do all electrical
work.

Turn off the unit.

Turn the power disconnect switch to the OFF position.

Disconnect the refrigeration unit from your electrical supply, if necessary.

Refer to the Lock-out Tag-out procedure on preceding pages if the unit requires service.
825101-00 (Rev C)
Page 17
Safety Information
PGC Manual
This page intentionally left blank
825101-00 (Rev C)
Page 18
Overview
PGC Manual
2 OVERVIEW
2.1
System Diagrams
Customer
Gas
Supply
Vent
Gas Out
Host
Equipment
Gas
Flow
Sw.
In
Flow
Control
Option
Valve
Gas In
Expansion
Tank
Gas Out
Refrigeration
Cooling Stack
Supply
Pressure
Gauge
Air or Water
Cooled
Condenser
Cooling Water*
Return
Refrigeration
Compressor
Unit
* Water Cooled units only.
Figure 2-1: System Block Diagram
825101-00 (Rev C)
Page 19
Overview
PGC Manual
Facility Power Drop
208 1 Phase 50/60 Hz
EMO
Power Switch
MCB1
Safety
Interlocks
Remote/Local
Bypass
System
Remote
Interface
Motor
Contactor
Refrigeration
Compressor
Unit
Flow
Control
Option
Remote
Controller
Thermocouple
Gauge
Valve
Host
Equipment
Flow
Switch
EMO*
Gas
Outlet
Customer Supplied
Optional Equipment
* Flow Control Option EMO does not operate locally. It is provided for customer to
wire as a remote EMO for the host equipment.
Figure 2-2: Electrical Distribution Diagram
825101-00 (Rev C)
Page 20
Overview
PGC Manual
Figure 2-3: System Dimensions
2.2
About the PGC
The PGC is a refrigeration unit that cools a stream of gas to cryogenic temperatures. It consists of two
separate circuits: a refrigerant circuit and a gas circuit.
The refrigerant circuit is located entirely within the PGC. The compressor pumps the refrigerant in a
®
continuous loop through the Polycold stack. The condenser removes heat from the refrigerant, and the
®
Polycold stack cools the refrigerant to cryogenic temperatures. (The refrigerant is actually a proprietary
mixture of refrigerants provided by Brooks Automation Inc.)
The gas circuit consists of a continuous copper tube that runs next to the refrigerant circuit. The gas is
cooled as it runs parallel to the cold refrigerant. (Performance specifications assume that ambient air
temperature is no higher than 79°F (26°C).
825101-00 (Rev C)
Page 21
Overview
2.3
PGC Manual
PGC 152 Model Features
Suction Gage: This gage displays the compressor's suction pressure while the PGC is operating; it
also displays the balance pressure after the PGC is off for 24 hours.
Gas Inlet: This is the beginning of the internal gas circuit, and the tube to which you connect your gas
source. Note: The materials used in the gas portion of the system are intended for use with dry gases
(Air and inert gasses N2, Argon, Helium) only.
Gas Outlet: This is the end of the internal gas circuit where the cold gas exits.
Gas-Outlet Thermocouple Wire: (See Figure 2-5.) If attached to a type-T temperature meter, this wire
®
indicates the temperature of the Gas Outlet just inside the Polycold stack. You may use it to monitor
the PGC's performance when gas is flowing.
Power Switch with Thermal Circuit Breaker: If the current exceeds 16 amps, the circuit breaker is
triggered and turns off the power switch.
Fan & Cooling Coil: The condenser on air-cooled models removes heat from the refrigerant by
drawing ambient air across a coil.
Cooling Water Inlet & Outlet: The condenser on water-cooled models requires customer supplied
cooling water to remove heat from the refrigerant.
Note: The PGC does not have a thermostat on the gas outlet. It is designed to cool the gas stream to
the coldest temperature possible, depending on the load. (See Figure 3-4.)
The above features are illustrated on an air-cooled gas chiller without a flow control unit and a watercooled gas chiller with a flow control unit. For brevity, only (2) of (4) model configurations shown,
however both air and water-cooled models can be configured with or without the optional flow control
unit.
825101-00 (Rev C)
Page 22
Overview
PGC Manual
2.3.1 Exterior Features, Air Cooled PGC 152 w/o Flow Control Unit
Top Rear
Edge
Gas
Outlet
Gas
Inlet
Suction
Gauge
Power Switch
Circuit Breaker
Figure 2-4: Air Cooled PGC 152 w/o Flow Control (Ext. Panels Installed)
825101-00 (Rev C)
Page 23
Overview
PGC Manual
2.3.2 Interior Features, Air Cooled PGC 152 w/o Flow Control Unit
Rear View Fan & Coils
Fan &
Cooling
Coils
Gas Outlet
ThermoCouple Wire
1of 4 Seismic
Anchor Points
Figure 2-5: Air Cooled PGC 152 w/o Flow Control (Ext. Panels Removed)
825101-00 (Rev C)
Page 24
Overview
PGC Manual
2.3.3 Exterior Features, Water Cooled PGC 152 with Flow Control Unit
Gas
Inlet
Suction
Gauge
Gas
Outlet
Power Switch
Circuit Breaker
Figure 2-6: Water Cooled PGC 152 w/ Flow Control (Ext. Panels Installed)
825101-00 (Rev C)
Page 25
Overview
PGC Manual
2.3.4 Interior Features, Water Cooled PGC 152 with Flow Control Unit
Gas Outlet
Thermo-Couple Wire
Cooling Water
Inlet & Outlet
Figure 2-7: Water Cooled PGC 152 w/ Flow Control (Ext. Panels Removed)
825101-00 (Rev C)
Page 26
Installation
PGC Manual
3 INSTALLATION
3.1
3.2
Tools and Materials Required

Pallet Truck, Hand Truck, or Dolly

230V plug to fit power supply (may be supplied with power cord assembly)

Wire Stripper

Small Screwdriver
Inspect the PGC
Notify the carrier immediately if you suspect the PGC was damaged during shipping. Read the outer
black dial of the SUCTION GAGE and record the balance pressure: ________ psig. The balance
pressure should be 140-160 psig for a PGC-152. If not, contact your local sales representative or
Brooks Automation Inc. for assistance.
3.3
Position the PGC
WARNING! Due to its weight, two persons are
required to move the PGC from the transport unit.

Place the PGC as close as possible to the desired location of your cold gas stream.

The PGC should be transported from the receiving area to its installed location on a hand truck,
dolly, or pallet truck

The PGC must remain vertical during transport and installation.

The PGC installation location must be indoors, in a well-ventilated area greater than 100 ft (2.83
3
m ), ambient temperature 40-90°F(4-32°C), relative humidity (RH) 20-80%, no condensation.

Placing the PGC in a confined area will increase the time required to service and maintain the unit.
We recommend providing as much clear service access as the facility will allow. If possible, allow
36 inches (90cm) of clear space at the front and rear of the unit.

Water-Cooled PGC’s may be placed side by side without clear space between them.

The Air-Cooled PGC requires 12 inches (30 cm) of clear space on the left and right sides, and 18
inches (45cm) of clear space on the top and rear sides to ensure sufficient air flow to cool the
condenser.
3
WARNING! Allowing hot air exhaust from one unit to enter an adjacent unit will
result in a high temperature fault. When installing multiple air cooled units, hot
air exhausting from one unit must be directed away from the air intake of
adjacent units. See Fig. 3-1.

The Air-Cooled PGC requires air in the acceptable ambient temperature range to cool its condenser.
Do not place the Air-Cooled PGC adjacent to equipment that emits heated air. The heated air will
not cool the units condenser adequately.

Performance specifications assume the ambient air temperature is no higher than 79°F (26°C).
Performance will decrease as the ambient temperature rises.

The base frame of the PGC can be secured to the floor at the four locations labeled Seismic Anchor
Point.
825101-00 (Rev C)
Page 27
Installation
PGC Manual

Air Out
Front
PGC-152
Front
PGC-152
Air Out
PGC-152
PGC-152
}
0.3m
12" MIN
PGC-152
Air In
PGC-152
}
Air In
0.3m
12" MIN
Fig 3.1
3.4
Cooling Water Connection (WC Units)
Tools and materials needed:

1/2-inch (15 mm) standard pipe size wrench.

Adjustable or open ended wrench for fittings supplied by customer
Verify your cooling water is adequate:

The inlet water temperature must be 55-85°F (13-29°C).

Refer to the table below to determine the minimum acceptable cooling water flow rate based on the
cooling water temperature.

Cooling water temperature varies between seasons. Cooling water lines within the PGC are not
insulated. To prevent condensation inside the system enclosure, ensure that the cooling water
temperature is higher than the dew point at the installed location.

Maximum working pressure of the cooling water circuit is 200 psig (1380 kPa).

Cooling water must be clean and suitable for use in copper based heat exchangers. Filter cooling
water that is dirty or contains abrasives.

Chemical impurities in the cooling water must be compatible with copper.
825101-00 (Rev C)
Page 28
Installation
PGC Manual
Connect a supply and a drain line to the refrigeration unit.

Use the pipe size specified at the beginning of this section.

The Cooling Water connections are 1/2-inch female NPT fittings.

Connect the supply line to the port marked IN. Connect your drain line to the port marked OUT. The
cooling water must flow in this direction to properly cool the unit.

Verify that the cooling water plumbing does not leak.
Refrigeration
Unit
Water Inlet
Temperature
° F (° C)
Minimum
Flow Rate
Gpm (L/min)
Pressure Drop
Inside Unit
Psi (kPa)
PGC 152
59 (15)
75 (24)
87 (30)
.68 (2.6)
1.1 (4.3)
2.0 (7.6)
<1 (<7)
<1 (<7)
3 (21)
Heat Rejection
Btu/hour (kW)
23,900 (7.0)
Table 3-1: Cooling Water Flow/Temperature Requirements
‡
CAUTION!
EQUIPMENT DAMAGE
Do not turn on the unit until the cooling water
has been connected and turned on.
3.5
Connect the Gas-Outlet Thermocouple Wire to a Temperature Meter
(Optional)
Tools Required:

Philips Screwdriver

Thermal Wire Stripper
®
 Temperature Meter (Suitable for reading type-T copper-constantan thermocouple wire)
First, lock-out & tag-out the unit as described in the Safety section. Then remove the PGC's front panel.
Locate the Gas-Outlet Thermocouple Wire, which is the brown insulated wire directly to the left of the
Suction Gage. Uncoil the wire, thread it through the ventilation grating and re-install the front panel.
Strip the thermocouple wires' brown jacket to fit your temperature meter. Separate and strip insulation
from the ends of the red & blue thermocouple wires. Connect the thermocouple wires to your
temperature meter. (Red is negative; blue is positive.)
Note: You may also want to attach a type-T (copper-constantan) thermocouple to the end of your
insulated gas-out line. This thermocouple would allow you to measure the actual temperature of your
exiting gas stream, and determine the amount of heat loss on the gas-out line (by comparing the
temperatures of the two thermocouples). See section 8.2 "Thermocouple Attachment Specification" for
instructions.
825101-00 (Rev C)
Page 29
Installation
3.6
PGC Manual
Connect the Electrical Power
‡
WARNING †
HAZARDOUS VOLTAGES
Electrical power to the PGC-152 must be connected by qualified
personnel according to local codes.
‡
WARNING †
HAZARDOUS VOLTAGES EXIST AT ALL TIMES AFTER THE
POWER IS CONNECTED
Adhere to the Lock-out Tag-out procedures described in the
Safety section when performing any subsequent installation or
maintenance operations.
The circuit breaker on the host equipment used as the main disconnect switch for the PGC should be
operator accessible, located in sight and within 25' of the PGC. Before connecting the PGC to your
power source, verify the following:

Your actual voltage falls within the acceptable range listed in the Table below

Your electrical supply must have enough capacity to handle the Rated Load Amps and should be
provided through a circuit breaker rated with at least 10,000 AIC. Recommended circuit breaker
rating is 20 amps.

The PGC is grounded according to your local codes.

The PGC has been installed so that it is protected by the Emergency Off circuitry of the host
equipment. (The PGC is intended to function as a subsystem of the host equipment, it does not
have its own EMO circuitry.)
For additional information, you may wish to refer to the electrical schematics in section 10.
825101-00 (Rev C)
Page 30
Installation
PGC Manual
Nominal
Compressor
Rating (volts)
Acceptable Voltage Range
200/208-1-50
180-229
3
At 50 Hertz
Rated Load Amps
1, 2, 3
10A, 16A
At 60 Hertz
208/230-1-60
10A, 16A
187-253
1
Rated Load Amps (RLA) is the current drawn by the compressor at rated load. It may also
be referred to as the maximum full load amps.
2
RLA listed is based on 80% of unit circuit breaker rating and adherence to the specified
voltage range. Operation outside this voltage range (particularly higher voltage at 50 Hz) will
result in excessive current draw and may cause the circuit breaker to trip.
3
Units built prior to April 11, 2005 had a 16A circuit breaker. This limits the 50Hz voltage
range to 180-220V and has a corresponding RLA of 12.8A.
Note: The compressor is provided with motor over temperature protection that complies
with UL and NEC definitions of inherent thermal protection.
Table 3-2: Electrical Requirements
3.7
Connection of Flow Control Unit (Optional)
Refer to the Flow Control Unit’s circuit diagram in the Process & Instrumentation and Electrical
Schematics section for wiring details.
Connect the Flow Control Unit to the Host Equipment to enable the remote Flow Control and Monitoring.
Specifications:

Flow Switch

Solenoid Valve 24V DC @ 37mA (minimum requirement)
Rated 20VA (0-30V .3A, 240V .06A)
The EMO switch on the Flow Control Unit does not operate locally. If desired, the EMO switch may be
incorporated into the host equipment EMO circuitry
3.8
Power Interruption/Restoration
The PGC system is configured with a single on/off switch. In the event of power interruption, the PGC
ceases operation. On restoration of electrical power, the PGC system will restart without operator
intervention. To place the equipment in a safe shut-down condition, turn the PGC Main Power Switch
OFF.
3.9
PGC Remote Control System (Optional)
The remote control system provides two distinct functions: Remote monitoring of the run status of the
unit, and remote on/off control of the unit. The remote monitoring feature is always available.
Availability of the remote on/off feature is controlled by jumper configuration. (See following section.)
Isolation between the remote control and the high voltage circuits of the system is provided by the
Relays. The isolation between coil circuit and contact circuit is rated at a minimum of 2000 VAC.
Specifications:

ON/OFF Control Voltage = 24V DC @ 37mA (minimum requirement)
825101-00 (Rev C)
Page 31
Installation

PGC Manual
Run Monitor Output Rated: 300V @ 1 AMP (maximum)
Remote Connector Pin outs

Pin #1 = + 24 VDC On/Off Control Input

Pin #2 = - 24 VDC On/Off Control Input

Pin #3 = Run Status Contact (Source)

Pin #4 = Run Status Contact (Return)
5
4
3
2
1
FRONT VIEW DE9 MALE
3.10 Enable Remote On/Off Operation
First, lock-out & tag-out the unit as described in the Safety section. Then, remove the PGC front panel.
Locate the E-Box cover retaining screws. Use a standard flat blade screwdriver to loosen the screws
then, swing open the cover. Disconnect the Remote Bypass Jumper located in the bottom of the E-Box.
(See figure on following page.) Close the E-Box cover, tighten the screws, and re-install the front panel.
Re-establish power to the unit and set the power switch to the ON (l) position. The unit will now respond
to remote ON/OFF control.
Remote
Bypass
Jumper
Figure 3-2: Remote Bypass Jumper
825101-00 (Rev C)
Page 32
Installation
PGC Manual
To turn the unit ON, apply 24 VDC of the proper polarity to Pin #1 & Pin #2 (see pin outs above).
CAUTION! Reversing the polarity of this connection may cause permanent damage to the parallel
protection diode across the relay coil.
The Run Status Contact should close once the unit is running. This will close the connection from Pin #3
to Pin #4. This contact may be used to turn on a remote indication device, or be monitored by a PLC.
For more specific information, refer to the circuit diagrams in the Process & Instrumentation and
Electrical Schematic section.
3.11 Install the External Gas Circuit
Tools and materials needed:

Tubing or hoses with 3/8-inch inner diameter

Armaflex or equivalent closed-cell insulation rated for cryogenic temperatures

Armaflex tape or equivalent

Armstrong 520 adhesive or equivalent
®
®
825101-00 (Rev C)
®
Page 33
Installation
PGC Manual
Verify the Gas Source is Adequate.
If your gas contains moisture, the water will condense and freeze in the gas circuit. The PGC
performance will degrade as the gas circuit becomes blocked. The PGC system is designed for use with
inert gases (Nitrogen, Argon, Helium) only. Contact Brooks Automation Inc. prior to introduction of gases
other than those specified.
To avoid any blockage, your gas should have a dew point colder than -80°C. However, if your gas has a
dew point of -60°C, the PGC will perform long enough for most applications. If the gas circuit becomes
blocked, see the Inspection & Maintenance section.
‡
WARNING †
EXPLOSION HAZARD
Do not exceed 100 psi supply pressure to PGC flow control unit.
The figure below identifies the gas inlet and outlet on the optional Flow Control Unit of the PGC. Do not
exceed 100 psi supply pressure when connecting gas to the inlet of the Flow Control Unit.
Gas
Inlet
Gas
Outlet
Figure 3-3: Optional Flow Control Gas Inlet & Outlet
‡
WARNING †
EXPLOSION HAZARD
Do not exceed 400 psi supply pressure to PGC.
The following figure identifies the gas inlet and outlet on a PGC without the optional Flow Control Unit. Do not
exceed 400 psi supply pressure when connecting gas directly to the inlet of the PGC.
825101-00 (Rev C)
Page 34
Installation
PGC Manual
Top
Rear Edge
Gas
Outlet
Gas
Inlet
Figure 3-4: PGC Gas Inlet & Outlet
Connect:

The gas source to the unit’s GAS INLET

The unit’s GAS OUTLET to the location you wish to direct the cold gas stream.
Hoses with clamps or metal tubing are both acceptable.
Use hoses with clamps or metal tubing with flare unions if you want to be able to disconnect the external
gas circuit easily. (This allows for easier removal of moisture from the internal gas circuit, especially if
your equipment is sensitive to water.)
Use copper tubing (not stainless steel) if you want to attach a thermocouple to the gas-out line. (See
section 3.4 for thermocouple installation details.)
If you will be brazing, see the section on “Brazing Specifications”.
Insulate the full length of the gas-out line with at least 1-1/4 inches of insulation for maximum
performance. Completely seal all seams with glue or tape. This keeps moisture from collecting on the
gas-out line when it is cold.
CAUTION! If using Armstrong adhesive, the work area must be adequately
ventilated and free of ignition sources. Read the container label and follow the
manufacturer’s instructions.
Set the Flow Rate at the gas supply tanks.
825101-00 (Rev C)
Page 35
Installation
PGC Manual
Rotameter-type flow meters assume standard temperature and pressure to determine flow rate. They
should be installed upstream on the gas-in line. You can use this meter on the gas out line temporarily
to calibrate gas flow when the PGC is off.
Use the following chart to determine the desired flow rate. The chart is based on data from units
powered by a 60 Hz electrical supply and operated at an ambient air temperature no higher than 79°F
(26°C).

Outlet temperatures are typically 5°C higher when the units are powered by a 50 Hz electrical
supply.

Performance will decrease as the ambient temperature rises.
Figure 3-5: PGC-152 Typical Capacity (Flow Rate vs. Gas-Outlet Temperature)
825101-00 (Rev C)
Page 36
Operation
PGC Manual
4 OPERATION
4.1
Starting the Polycold Gas Chiller
Caution! The PGC will condense water in the gas circuit if the
®
Polycold stack is cold, and dry gas is not being pumped
though the gas circuit.
Condensation of water in the gas circuit could occur while your are waiting for the stack to cool after
turning on the PGC, and up to four hours after turning off the PGC.
If your equipment is sensitive to water, avoid condensation while not in use by plugging the open end(s)
of the gas circuit, or by allowing a small amount (about 5 SCFH) of dry gas to purge the gas circuit.
Turn on the PGC*. Allow it to cool for 20 minutes. Supply the gas flow for your application. The Gas
Outlet should reach temperature in 25 minutes. (See Figure 3-4.)
*If equipped with Optional Flow Control Unit:

Supply the control voltage to start the unit. (See section 3.7)

The EMO switch on the Flow Control Unit does not operate locally. If desired, the EMO switch may
be incorporated into the host equipment EMO circuitry
825101-00 (Rev C)
Page 37
Operation
PGC Manual
This page intentionally left blank
825101-00 (Rev C)
Page 38
Inspection & Maintenance
PGC Manual
5 INSPECTION & MAINTENANCE
5.1
Periodic Inspection
Inspect the PGC:
5.2
5.3
5.4
5.5
5.6

Every six months.

Whenever it is necessary to remove water from the gas circuit.

Whenever there is a leak.
Inspect for water condensation in the gas circuit.

Condensation of water in the gas circuit could occur while waiting for the stack to cool after turning
on the PGC, and up to four hours after turning off the PGC.

If your equipment is sensitive to water, avoid condensation while not in use by plugging the open
end(s) of the gas circuit, or by allowing a small amount (about 5 SCFH) of dry gas to purge the gas
circuit.
If the unit is Air-Cooled, verify there is adequate air circulation
through the condenser.

The Air-Cooled PGC requires 12 inches (30 cm) of clear space on the left and right sides, and 18
inches (45cm) of clear space on the top and rear sides to ensure sufficient air flow to cool the
condenser.

The PGC requires that approximately 1200 CFM of air be drawn across the condenser coil to
achieve optimum performance of the system.

Performance specifications assume the ambient air temperature is no higher than 79°F (26°C).
Performance will decrease as the ambient temperature rises.

The condenser fins must be clean and straight. If not, turn the unit off. Lockout the power as
discussed in the Safety section. Then, clean and inspect the unit. . Use a vacuum to remove dust
and lint. Use a condenser fin comb to straighten the fins.
If the unit is Water-Cooled, verify the following:

There are no leaks in the cooling water circuit.

The cooling water hoses are in good condition.

The cooling water flow and temperature are adequate. (See Table 3-1.)
Verify the insulation on the gas-out line is adequate.

The insulation should be air tight.

It should not be cracked or holding moisture.

If necessary, turn off the PGC and replace the insulation. (See section titled "Install the External
Gas Circuit".)
Verify the refrigerant circuit does not have a leak.

Turn off the PGC and wait 24 hours.
825101-00 (Rev C)
Page 39
Inspection & Maintenance
5.7
PGC Manual

The balance pressure should be within 7 psig of the pressure you recorded in the section 3.2.
(Inspect the PGC)

If the balance pressure has dropped more than 7 psig, the refrigerant circuit may have a leak.
Remove moisture from the gas circuit.
WARNING! Moisture in the gas circuit while the PGC is operating
will freeze, and may block gas flow.

If your equipment is sensitive to water, disconnect your external gas-out line from the Gas-Outlet.

Verify the refrigerant circuit does not leak. (See previous paragraph.)

Allow your gas supply to flow (at about 50 SCFH) through the gas circuit until the exiting gas is dry.

The exiting gas should be dry in about 10 minutes.
825101-00 (Rev C)
Page 40
Troubleshooting
PGC Manual
6 TROUBLESHOOTING
6.1
The PGC's Compressor Does Not Start Or Run Properly
Note: See Section 6.4 for troubleshooting and diagnostics based on the indicator lights .
WARNING! Contact your local sales representative or the Brooks
Automation Inc. Service Department if you need assistance troubleshooting or repairing your PGC. Be sure to do this if the compressor has
an internal problem, if the refrigerant circuit has a leak, or if the fan needs
to be replaced.
6.1.1 Fan and compressor do not start (and make no noise).
If the On/Off switch stays in the ON position, verify the following.

PGC has power.

Power supply is adequate.
If the On/Off switch has returned to the OFF position (by its circuit breaker), verify the following.

Power supply is adequate.
6.1.2 Compressor hums or starts, and then stops.
The circuit breaker for the On/Off switch may have tripped. Or, the thermal overload protector for the
compressor may be cycling the compressor on and off. Verify the following.
6.2

Fan is working. (Air-Cooled Models)

Cooling Water supply is adequate. (Water-Cooled Models)

Power supply is adequate.
Gas Flow or Temperature Is Inadequate
See Inspection & Maintenance, and verify the following:
6.3

Inlet gas flow is within specification. (See Figure 3-4.)

Gas circuit is not plugged.

Gas circuit does not have a leak.

Insulation on the gas-out line is adequate.

Air circulation through the condenser is adequate.

Cooling water supply to condenser is adequate

Refrigerant circuit does not have a leak.
PGC Makes Unusual Noises
Verify the following.

There are no loose parts (such as the fan shroud or fan blade).
825101-00 (Rev C)
Page 41
Troubleshooting
6.4
PGC Manual

A tube is not rubbing or rattling against another surface.

The fan blade is not bent. (Air-Cooled Models)

Fan motor bearings are not worn. (Air-Cooled Models)
Indicator Lamp Based Troubleshooting and Diagnostics
This symbol represents an indicator light being ON in the diagrams below.
STATIC MODE 1 (UNIT NOT RUNNING – NO LINE POWER PRESENT)
INDICATOR
COLOR
STATUS
LINE
YELLOW
OFF
RUN
GREEN
OFF
FAULT
RED
OFF
POWER
ORANGE
OFF
POWER SW=
N.A.
STATIC MODE 2
INDICATOR
(UNIT NOT RUNNING – LINE POWER PRESENT)
COLOR
STATUS
LINE
YELLOW
ON
RUN
GREEN
OFF
FAULT
RED
OFF
POWER
ORANGE
OFF
POWER SW=
OFF
825101-00 (Rev C)
Page 42
Troubleshooting
PGC Manual
RUN MODE
(UNIT RUNNING - SYSTEM OK)
INDICATOR
LED COLOR
STATUS
LINE
YELLOW
ON
RUN
GREEN
ON
FAULT
RED
OFF
POWER
ORANGE
ON
POWER SW =
ON
FAULT MODE 1
(NOT RUNNING - PRESS/TEMP TRIP OCCURRED)
INDICATOR
LED COLOR
STATUS
LINE
YELLOW
ON
RUN
GREEN
OFF
FAULT
RED
ON
POWER
ORANGE
ON
POWER SW =
ON
FAULT MODE 2 (NOT RUNNING - CIRCUIT BREAKER SWITCH TRIPPED)
INDICATOR
LED COLOR
STATUS
LINE
YELLOW
ON
RUN
GREEN
OFF
FAULT
RED
OFF
POWER
ORANGE
OFF
POWER SW =
ON
825101-00 (Rev C)
Page 43
Troubleshooting
PGC Manual
FAULT MODE 3 (NOT RUNNING - COMPRESSOR OVERLOAD TRIPPED)
INDICATOR
LED COLOR
STATUS
LINE
YELLOW
ON
RUN
GREEN
ON
FAULT
RED
OFF
POWER
ORANGE
ON
POWER SW =
ON
Indicator Lamp Fault Conditions Explained
The FAULT INDICATOR was designed to show over-pressure (compressor discharge) or overtemperature (condenser liquid line) fault conditions (FAULT MODE 1). However, there are two other
fault conditions which have the same overall effect on the system, but won’t show as a normal FAULT
indication. These are as follows:
FAULT MODE 2 would be the result of the Circuit Breaker Switch tripping under excessive load
conditions, something that would occur if a short circuit were present or if the compressor seized. The
symptoms would resemble a STATIC MODE 2 condition. With the exception that the switch would have
automatically turned it self OFF, following a previous RUN MODE condition.
FAULT MODE 3 would usually only occur if the internal overload of the compressor were to open. This
would appear to be RUN MODE and there would be no indication of this on any of the status indicators.
The Fault would show itself as a cyclic action of the compressor (automatically turning on and off). This
type of fault would be indicative of a bad compressor.
Fault Mode 1 Corrective Actions
If a FAULT MODE 1 condition has occurred, the RED light will be lit and the compressor will be
inoperative. On Air-Cooled Models, the cooling fan will also be inoperative. First, perform a lock-out /
tag-out procedure. Remove the left and rear panels to provide access to the manual resets for the
pressure switch and the thermostat. To reset the pressure switch (located at the rear of the unit) move
the green lever upwards. To reset the thermostat (located on left side of unit) depress the green button.
A click will be heard when either component resets. The compressor will attempt a restart when
electrical power is restored, safety devices are reset, and the unit is switched ON again.
Following a reset, it is important to determine what caused the fault in initially:
In the case of a thermostat trip on a unit with an air-cooled condenser, observe whether the fan resumes
operation and produces a steady breeze when the unit is re-started. Also, watch the fan for a few
minutes to see if it is instable, or slows over time. Check the inlet side of the condenser cooling coil for
any accumulated build-up of dirt. If so, clean it out with either an air hose, or a vacuum cleaner.
825101-00 (Rev C)
Page 44
Troubleshooting
PGC Manual
In the case of a thermostat trip on a unit with a water-cooled condenser, check the cooling water for
adequate flow and temperature.
If the fault condition tripped the pressure switch, it may indicate that the process load may be too
excessive for the units’ compressor, causing high discharge pressures to exist. Reducing the process
gas flow or lowering the gas inlet temperature would in effect lower the system load, and the discharge
pressure. The condenser may also be dirty. There is also the possibility, although remote, that a
refrigerant leak has caused higher discharge pressures. To ascertain if this is the reason; allow the unit
to fully warm up then, check the units’ balance pressure on the front panel gauge. See if the pressure
has dropped noticeably, perhaps repeating the check on subsequent days, to verify a dropping
pressure.
Fault Modes 2 and 3 Corrective Actions
Call your certified service agent or Brooks Automation Inc.
825101-00 (Rev C)
Page 45
Troubleshooting
PGC Manual
This page intentionally left blank
825101-00 (Rev C)
Page 46
Disconnection, Storage and Reshipment
PGC Manual
7 DISCONNECTION, STORAGE, AND
RESHIPMENT
7.1
Disconnection
Shut down power to the PGC and allow the system to reach ambient temperature (allow 24 hours to
reach thermal equilibrium)
Disconnect facility electrical power from the PGC.
Disconnect remote operation or EMO cabling from the unit.
Disconnect the gas supply line.
Cap the gas inlet & outlet to prevent diffusion of moisture into the system.
If water-cooled, turn off the cooling water lines and disconnect. Use compressed air to blow out
remaining water from the lines.
7.2
Packing for Reshipment or Storage
‡
WARNING †
LIFTING HAZARD (235 pounds (107 kg))
Use appropriate lifting technique & proper
equipment to prevent injury.
The PGC should be appropriately packaged for shipment. (Securely strapped to shipping pallet and
covered for protection.) Contact Brooks Automation Inc. for additional information on packaging and
shipping.
825101-00 (Rev C)
Page 47
Disconnection, Storage and Reshipment
PGC Manual
This page intentionally left blank
825101-00 (Rev C)
Page 48
Appendix
PGC Manual
8 APPENDIX
8.1
BRAZING SPECIFICATION
Tools and materials needed:

Tubing cutter

Reamer

Sandpaper or wire brush or steel wool

Pressure or flow regulated dry nitrogen gas

Oxy-acetylene torch or air-acetylene torch (propane is not hot enough)

For copper-to-copper joints use: Harris Dynaflow or Handy & Harman Sil-Fos 6M or equivalent alloy

For copper-to-stainless steel or copper-to-brass joints use: Harris Safety-Silv 56 or Handy &
Harman Braze 560 or equivalent silver alloy

Harris Stay-Silv black flux or Handy Flux Type B-1 or equivalent
Note: Brazing operations should be performed by qualified technicians.
8.2

Thoroughly clean all mating surfaces to bare metal.

Purge the tubes with dry nitrogen gas while brazing and until the tubes and joints have cooled to
below 190EC. (This prevents internal scale formation or oxidation.)

Remove all excess flux from the brazed joints. Use a wet rag while the brazed joint is still hot.
Dispose of the contaminated waste in a manner approved by the location.

Carefully inspect each joint for the proper flow of the brazing alloy. Both surfaces should be
"wetted" by the alloy.

Carefully check all joints for leaks.
THERMOCOUPLE ATTACHMENT SPECIFICATION
Tools and materials needed:

Type T (copper-constantan) thermocouple wire

Thermal wire stripper
Tools and materials needed for soldering:

Sand paper

Propane torch

Rosin flux

Harris Bridgit or equivalent lead-free solder

Neutralizing agent (to remove the flux)
Note: Brazing operations should be performed by qualified technicians.
825101-00 (Rev C)
Page 49
Appendix
PGC Manual

Thoroughly clean all mating surfaces to bare metal.

Purge the tubes with dry nitrogen while brazing and until the tubes and joints have cooled to below
190’C.

Remove 2 inch (13 mm) of insulation from one end of the thermocouple wire. Twist the two wires
together, and apply flux and pre-tin the twisted wires.

Use sandpaper to remove oxidation from the copper tube, and apply flux and pre-tin the tube.

Apply flux to the pre-tinned wires and to the pre-tinned copper tube.

Position the thermocouple wire so that the first twist of wire (nearest the insulation) is against the
tube.

Solder the wire twist to the copper tube. Do not overheat the flux. Do not melt or cut the plastic
insulation on the thermocouple wire or it may create false readings.

Important! Make certain the wire twist closest to the insulation is in contact with the copper tube.
(It is the first twist of wire closest to the insulation that senses and determines the temperature
reading.)

Remove the flux residue using a wet cloth. Dispose of the contaminated waste in an approved
manner.

Wrap the thermocouple wire tightly around the tube 3-4 times.

Secure the wire with tie wrap(s) or tape suitable for cryogenic temperatures. Allow enough
thermocouple wire to reach your temperature meter.

Apply insulation as described in the Section titled “Install the External Gas Circuit”.
825101-00 (Rev C)
Page 50
Appendix
8.3
PGC Manual
Specifications
Model Type
Air Cooled
Air Cool w/
Flow Control
Water Cooled
Shipping Weight:
235 pounds.
(107 kg)
247 pounds
(112 kg)
235 pounds.
(107 kg)
Frequency
50-60Hz
NominalVoltage
200, 208V
208, 230V
Gas-Inlet &
Outlet Lines:
3/8-inch OD
tube
3/8-inch male
comp. ftg
Cooling Air
Required:
Note: Internal fan
provides air
circulation
1200 CFM
1200 CFM
Voltage
Cooling Water
Requirements
N/A
N/A
Water Cool w/
Flow Control
247 pounds
(112 kg)
Acceptable VoltageRange
180-229V
187-253V
3/8-inch OD
tube
N/A
See Table 3-1
3/8-inch male
comp. ftg
N/A
See Table 3-1
Balance Pressure:
140-160 psig
Maximum Gas
Flow Rate:
500 SCFH, 100psig max.
Ambient Air
Temperature:
4 - 32°C (40 - 90°F)
Approximate Heat
Rejection Rate:
4650w (15,870 BTUH)
Noise Emissions:
Less than 70 dB(A)
Dimensions:
See Figure 2-3
Cooling Water
Requirements
See Table 3-1
Electrical
Requirements:
See Table 3-2
Cooling Capacity
See Figure 3-4
Refrigerant Charges:
Refrigerant charges are specified on unit nameplates. Contact your
local sales representative or Brooks Automation Inc. for a current price
list.
Table 8-1: General Specifications
825101-00 (Rev C)
Page 51
Appendix
PGC Manual
This page intentionally left blank
825101-00 (Rev C)
Page 52
Glossary
PGC Manual
9 GLOSSARY
ANSI: American National Standards Institute
ASHRAE: American Society of Heating, Refrigerating, and Air-Conditioning Engineers
AWG: American wire gauge
balance pressure: The pressure in the refrigeration unit when the suction and discharge sides of the
compressor are equal, and after the refrigerants have fully warmed up (24 hours).
CE: European conformity
Compressor: A component in the refrigeration unit that raises the refrigerant pressure and causes the
refrigerant to move through the circuit.
Condenser: A component in the refrigeration unit that removes heat from the refrigerant vapor after it
exits the compressor.
EC: European community.
EEC: European economic community
EN: European norm (or standard).
IEC: International Electrotechnical Commission.
Liquid line: A portion of the refrigerant circuit containing high pressure refrigerant just after it has been
cooled by the water-cooled condenser,
NEC: national electrical code.
NPT: national pipe thread.
®
Polycold stack: The upper portion of the refrigeration unit that is insulated with foam.
Refrigerant: A proprietary mixture of refrigerants made by Brooks Automation Inc. Polycold Systems.
Refrigerant circuit: The path of the refrigerant which goes from the refrigeration unit, through the feed
line, through the cryosurface, through the return line and back to the refrigeration unit.
Refrigerant expansion tank: A tank inside the refrigeration unit that maintains the gaseous refrigerant
at a safe pressure when the unit is not at operating temperature.
®
Refrigeration unit: The machine containing the compressor, condenser and Polycold stack that cools
the refrigerant mixture to cryogenic temperatures.
TC: thermocouple
TÜV: Technical Supervision Society—verifies compliance with EN and IEC standards.
UL: Underwriters Laboratories—verifies compliance with NEC standards
.
825101-00 (Rev C)
Page 53
Process & Instrumentation and Electrical Schematics
10
PGC Manual
PROCESS & INSTRUMENTATION
AND ELECTRICAL SCHEMATICS
825101-00 (Rev C)
Page 54
Process & Instrumentation and Electrical Schematics
PGC Manual
Figure 10-1: Process & Instrumentation Diagram, PGC-152 W/CE/S2
825101-00 (Rev C)
Page 55
Process & Instrumentation and Electrical Schematics
PGC Manual
Figure 10-2: Process & Instrumentation Diagram, PGC-152 CE/S2 W/ Flow Control
825101-00 (Rev C)
Page 56
Process & Instrumentation and Electrical Schematics
PGC Manual
Figure 10-3: Circuit Diagram, PGC-152 CE W/RMT IEC
825101-00 (Rev C)
Page 57
Process & Instrumentation and Electrical Schematics
PGC Manual
Figure 10-4: Circuit Diagram, PGC-152 CE/S2 Flow Control Option
825101-00 (Rev C)
Page 58