Three Phase Synchronous Generators

Transcription

Three Phase
Synchronous Generators
MJL SERIES
160 - 200 FRAME SIZES
SIN.CT.029.0 GB
STANDARDS
The new MJL generator series is designed in compliance with: BS EN 60034; BS 4999-5000; VDE 0530; NEMA MG 1.22 and bears the CE marking.
EXCITATION SYSTEM
The generators are self-excited by means of a brushless type excitation system.
The generators are equipped with an AVR type Mark V. The voltage stability is maintained within ±0,5% of the nominal value in steady condition with balanced and non
distorting load. The Mark V operates at 50 and 60 Hz frequency and it is equipped with a radio interference filter.
This regulator offers a low speed protection and over-excitation protection.
Manual Voltage Regulation
Available within ±5% of the rated value by means of a potentiometer placed inside the voltage regulator.
Remote voltage sensing is possible by means of an external potentiometer, which can be supplied on request.
VOLTAGE AND FREQUENCY
Generators can operate at 50 and 60 Hz.
Frame Size [mm]
Connection
160 ÷ 200
Voltage [V]
50 Hz
60 Hz
Series star
380 - 440
416 - 480
Parallel star
190 - 220
208 - 240
Series delta
220 - 254
240 - 277
WINDINGS
The generators are supplied with 2/3 pitch winding to reduce the voltage harmonic content in application with non-linear loads. The no-load voltage waveform is
sinusoidal with a residual harmonic less than 2%. The Total Harmonic Distortion (THD) is less than 2%. The Telephonic Harmonic Factor (THF) is less than 2% as defined
by BS 4999 part 40. The Radio Interference suppression complies to grade N of VDE 0875.
OVERLOADS
The overloads (only for continuous duty) are: 10% for 1 hour; 15% for 10 minutes; 30% for 4 minutes; 50% for 2 minutes. These overloads must be followed by at least
6 hours of running at nominal load or less.
INSULATION, IMPREGNATION AND PROTECTIVE TREATMENT OF WINDINGS
The insulation is H class. Generators are impregnated with high grade resin and a further protective treatment is applied on the whole range, making the generators
suitable for harsh environment conditions.
PROTECTION DEGREE
The standard protection degree is IP 23.
ROTOR BALANCING, BEARINGS & OVERSPEED
The rotors are dynamically balanced and are fitted with sealed-for-life ball bearings on single and double bearing configurations. The max overspeed allowed is 1,5 times
the rated speed (referred to 50 Hz).
Marelli Asia Pacific Sdn. Bhd. - Sales, Service and Distribution Centre
MarelliGenerators
®
INDUSTRIAL APPLICATION / LOW VOLTAGE
Type
Power rating [kVA]
Temp. rise / Ambient temp. [°C]
Continuous duty
Stand by
125/40
105/40
163/27
150/40
ΔT cl. H
ΔT cl. F
Leads
4 poles
Efficiency
4/4
pf = 0.8
125/40
[%]
Inertia
B3
Approx.
J
[kg m2]
Weight
B3
Approx.
[kg]
400 V @ 50 Hz - 1.500 rpm
IP23
MJL 160 XA4
MJL 160 SA4
MJL 160 SC4
MJL 160 MA4
MJL 160 MB4
12
12
12
12
12
13,5
16,0
23,0
28,0
32,0
12,5
15,0
20,4
25,5
29,1
15,0
17,5
25,0
30,5
34,8
14,0
16,5
24,0
29,5
33,7
84,0
84,1
84,9
87,5
87,0
0,106
0,128
0,165
0,205
0,230
106
117
136
152
168
MJL 200 SA4
MJL 200 SB4
MJL 200 MA4
MJL 200 MB4
12
12
12
12
42,0
50,0
60,0
75,0
37,1
45,0
53,0
68,7
46,0
55,0
66,0
82,0
44,5
53,0
61,0
79,0
87,2
88,2
88,7
90,0
0,369
0,424
0,488
0,615
247
254
278
325
4 poles
480 V @ 60 Hz - 1.800 rpm
IP23
MJL 160 XA4
MJL 160 SA4
MJL 160 SC4
MJL 160 MA4
MJL 160 MB4
12
12
12
12
12
16,2
19,2
27,6
33,6
38,4
14,8
17,6
25,2
30,8
35,1
17,8
21,1
30,4
37,0
42,2
17,3
20,5
29,4
35,8
41,0
84,2
84,3
85,6
88,2
87,6
0,106
0,128
0,165
0,205
0,230
106
117
136
152
168
MJL 200 SA4
MJL 200 SB4
MJL 200 MA4
MJL 200 MB4
12
12
12
12
50,4
60,0
72,0
90,0
46,2
55,0
66,0
82,4
55,4
66,0
79,2
115,0
53,8
64,0
76,8
95,0
88,1
89,0
89,6
90,5
0,369
0,424
0,488
0,615
247
254
278
325
Ratings refer to following conditions: balanced non-deforming load, altitude 1.000 m a.s.f., minimum power factor 0,8
OPERATING CONDITIONS
Single phase operation
Three phase (12-wire) wound generators can be reconnected and derated to 66% for single phase operation (with a zig-zag connection).
Transient ratings
The voltage drop due to the application of full load at 0,8 power factor inductive on the generators varies between 16 and 20% of the rated voltage: the output voltage
recovers to within 3% of the rated value in less than 0,3 seconds.
Altitude
The rated outputs refer to installation up to 1.000 m a.s.l.
Above this level the following derating factors must be applied.
Altitude [m a.s.l.]
< 1.000
< 1.500
< 2.000
< 2.500
< 3.000
K factor
1,00
0,96
0,93
0,90
0,86
Ambient temperature
The rated outputs given in this catalogue are based on a maximum ambient temperature of 40°C.
When operating at different ambient temperatures the output rating can be obtained by applying the factors as in the following table.
Ambient Temperature [°C]
30
35
40
45
50
55
K factor
1,04
1,00
1,00
0,96
0,93
0,90
Power factor
The nominal power factor is 0.8 lagging.
For different power factor values the following derating factors must be applied.
Power Factor
1
0,8
0,7
0,6
0,5
0,3
0
K factor
1,00
1,00
0,93
0,88
0,84
0,82
0,80
MarelliGenerators
®
DIMENSIONS
SINGLE BEARING 160 FRAME SIZE
11.5
5
AVR
L
340
100
240
CG
SAE 3
SAE 4
SAE 5
α
164
N
P
WA
WB
Ø316
257
Z
MA
0
-1,0
M
Ø60
PA
P
N
G
160
β
Y
13
N°6
12
90
105
40
90
254
180
300
206
MJL 160
L
CG SAE 5-4
CG SAE 3
CONNECTING
COUPLING
FLANGE
SAE J620
6½
7½
8
10
11½
4
•
•
•
•
•
•
•
MA
571
225
225
MB
571
250
245
COUPLING [mm]
FLANGE [mm]
Y
3
SAE
J620
PA
MA
•
•
•
6½
7½
8
10
11½
215,90
241,30
263,52
314,32
352,42
220,02
222,25
244,48
295,28
333,38
SAE J617
5
16
DIMENSIONS [mm]
SA
SC
453
491
190
205
185
200
XA
453
180
175
40
14
5
NR
Ø
6
8
6
8
8
9
9
11
11
11
β
WA
WB
60°
45°
60°
45°
45°
30,2
30,2
62,0
53,8
39,6
9.8
9.8
-
SAE
N
J617
5
4
3
0
-0,13
314,32
361,95
409,58
P
M
355
404
451
333,38
381,00
428,62
Z
NR
Ø
8 11
12 11
12 11
α
45°
30°
30°
DOUBLE BEARING 160 FRAME SIZE
AVR
L
340
100
240
Ø308
Ø316
N°8 M10
.75
Ø285
G
Ø266.70
Ø354
0
-0,13
48 k6
0
-1,0
51.5
45°
N°6
5
13
75
90
110
90
254
180
300
16
206
MJL 160
L
CG
XA
533
185
40
14
M12 DIN 332
DIMENSIONS [mm]
SA
SC
533
571
195
210
160
14 h9
257
164
CG
MA
651
230
MB
651
255
MarelliGenerators
®
SINGLE BEARING 200 FRAME SIZE
AVR
12
5
L
420
362
WA
α
CG
247
N
P
WB
67
0
-1.0
Ø375
PA
MA
M
G
Ø60
N
P
392
Z
200
β
6
Y
N°6
25
12
50
140
318
140
280
175
390
330
MJL 200
L
CG SAE 5-4
CG SAE 3-2-1
COUPLING
SAE J620
DIMENSIONS [mm]
SB
645
290
295
SA
645
280
285
7½
8
10
11½
14
SAE J617
4
•
•
•
•
•
28
MA
735
310
305
MB
735
330
325
COUPLING [mm]
CONNECTING
FLANGE
5
70
18.5
5
3
2
•
•
•
•
•
•
1
•
SAE
J620
PA
MA
7½
8
10
11½
14
241,30
263,52
314,32
352,42
466,72
222,25
244,48
295,28
333,38
438,15
Y
NR
Ø
8
6
8
8
8
9
11
11
11
14
FLANGE [mm]
β
WA
WB
45°
60°
45°
45°
45°
30.2
62.0
53.8
39.6
25.4
19.8
10.4
24.6
SAE
N
J617
5
4
3
2
1
0
-0,13
314,32
361,95
409,58
447,68
511,18
P
M
440
440
451
489
552
333,38
381,00
428,62
466,72
530,22
Z
NR
Ø
8
12
12
12
12
11
11
11
11
11
α
45°
30°
30°
30°
30°
DOUBLE BEARING 200 FRAME SIZE
AVR
L
67
420
CG
30°
0
-0.13
Ø381
0
-1.0
Ø375
Ø402
G
Ø361,95
Ø432
18
h9
60
m6
392
N°12 M10
247
362
N°6
5
25
85
140
140
318
140
280
390
330
MJL 200
L
CG
SA
695
245
70
18,5
M20 DIN 332
6
200
64
DIMENSIONS [mm]
SB
695
260
MA
785
270
28
MB
785
300
MarelliGenerators
®
HEADQUARTERS
ITALIAN BRANCHES
Marelli Motori S.p.A.
Milan
Via Sabbionara, 1
36071 Arzignano (VI) - Italy
(T) +39 0444 479.711
(F) +39 0444 479.888
www.marellimotori.com
[email protected]
Via Cesare Cantù, 29
20092 Cinisello Balsamo (MI) - Italy
(T) +39 02 660.131.66
(F) +39 02 660.134.83
[email protected]
Florence
Via Panciatichi, 37/2
50127 Firenze - Italy
(T) +39 055 431.838
(F) +39 055 433.351
[email protected]
MARELLI MOTORI OVERSEAS COMPANIES
GREAT BRITAIN
CENTRAL EUROPE
USA
Marelli UK, Ltd
Marelli Central Europe Gmbh
Marelli USA, Inc
Meadow Lane
Loughborough
Leicester LE111NB
UK
(T) +44 1509 615 518
(F) +44 1509 615 514
[email protected]
Heilswannenweg 50
31008 Elze
Germany
1620 Danville Road
PO Box 410
Harrodsburg, KY 40330
USA
(T) +1 859 734 2588
(F) +1 859 7340629
[email protected]
ASIA PACIFIC
SOUTH AFRICA
Marelli Asia Pacific Sdn Bhd
Marelli Electrical Machines South Africa (Pty) Ltd
Lot PT 5038-5041 Jalan Teluk Datuk 28/40
Off Persiaran Sepang, Seksyen 28,
40400 Shah Alam, Selangor D.E.
Malaysia
(T) +60 3 5192 7213
(F) +60 3 5192 6293
[email protected]
Unit 4, 55 Activia Rd - Activia Park
Elandsfontein,
1406 Gauteng
Republic of South Africa
(T) +27 11 822 5566
(F) +27 11 828 8089
[email protected]
SIN.CT.029.0 GB
(T) +49 5068 462 400
(F) +49 5068 462 409
[email protected]
MARELLI MOTORI reserves the right to change the design, technical specification and dimensions in order to update or improve its products, without prior notice
Three Phase
Synchronous Generators
160 - 900 FRAME SIZES
INDUSTRIAL / MARINE APPLICATIONS
SIN.CT.024.13 GB
CONTENT
Page
THE COMPANY
4
POWER RANGE
4
STANDARDS
5
5
AVAILABLE VOLTAGES (SPECIAL VOLTAGES)
5
WINDINGS
5
INSULATION, IMPREGNATION AND PROTECTIVE TREATMENT OF WINDING
5
RADIO INTERFERENCE
5
PROTECTION DEGREE
5
VENTILATION AND DIRECTION OF ROTATION
5
ROTOR BALANCING
5
VIBRATION
5
BEARINGS AND OVER SPEED
5
TESTING CAPABILITY
5
6
EXCITATION SYSTEM
7
THREE PHASE SHORT CIRCUIT CURRENT
7
AUTOMATIC VOLTAGE REGULATOR SPECIFICATIONS
7
SELECTION GUIDE - INDUSTRIAL APPLICATION / LOW VOLTAGE
8
SELECTION GUIDE - INDUSTRIAL APPLICATION / MEDIUM VOLTAGE
10
SELECTION GUIDE - INDUSTRIAL APPLICATION / HIGH VOLTAGE
12
SELECTION GUIDE - MARINE APPLICATION / LOW VOLTAGE
14
SELECTION GUIDE - MARINE APPLICATION / LOW VOLTAGE / WITH EXCHANGER
16
DRAWINGS
18
DIMENSIONS
19
THE COMPANY
Marelli Motori S.p.A. is an Italian manufacturer of electrical machines with a tradition dating back to 1891. Today Marelli Motori is recognized internationally as
a leading supplier of generators and electric motors. MarelliGenerators is the company brand specifically designed to offer a complete selection of synchronous
machines for low, medium and high voltage systems up to 15 kV. Fields of applications include conventional power, renewable energy and marine industry.
A wide range of standard and customised solutions is provided for industrial gen-sets, cogeneration, telecommunication, UPS systems, offshore, Oil & Gas,
shipboard power and hydropower plants.
RELIABILITY
Long life endurance of electrical components and housing.
Windings are impregnated with high quality processes and additional protection is used against tough environmental conditions.
The design ensures reliability under difficult operating conditions.
PERFORMANCE
The latest technologies and the highest quality materials are used to guarantee the best performances for any kind of application
KNOW HOW & CAPABILITIES
For special projects generators can be designed for specific application including:
Nominal voltage from 380 to 15000 Volts.
•
•
Polarities/speeds not mentioned in the following pages are available on request.
•
Single and double bearing solutions.
•
Ball, roller or sleeve bearings are available.
•
Anti condensation heaters are available.
•
Wide range of sensors to monitor stator winding and bearing temperatures.
•
Degree of protection up to IP55.
•
Auxiliary and neutral point terminal boxes.
•
Vibration sensors.
•
Neutral point current transformers (CT) are available (single core, double core or triple core).
•
Multicore voltage transformers.
POWER RANGE
INDUSTRIAL APPLICATION / LOW VOLTAGE
INDUSTRIAL APPLICATION / MEDIUM VOLTAGE
10
8
8
poles
poles
10
6
6
4
4
0
1000
2000
3000
4000
5000
0
2000
Nominal Output [kVA]
INDUSTRIAL APPLICATION / HIGH VOLTAGE
6000
8000
10000
MARINE APPLICATION / LOW VOLTAGE
8
8
poles
10
poles
10
6
6
4
4
0
2000
4000
6000
8000
10000
0
1000
2000
3000
50 Hz
4000
60 Hz
4000
5000
STANDARDS
All generators are designed in compliance with: EN 60034-1; BS 4999-5000; VDE 0530, NF 51-100; NF 51-111; OVE M-10; NEMA MG 1.22, and conform to
EU rules and are CE marked. The marine ranges are type approved by DNV.
On request MarelliMotori is able to supply UL/CSA certified generators (for the US market and the Canadian market).
The generators in standard configuration can operate at 50 Hz and 60 Hz. Different voltages are available on request.
Frame Size
160 ÷ 355 MA (12 leads generators)
Connection
Voltage at 50 Hz [V]
Series star
380 ÷ 440
380 ÷ 480
Parallel star
190 ÷ 220
190 ÷ 240
Series delta
220 ÷ 254
220 ÷ 277
Star
380 ÷ 415
416 - 480
Delta
230 ÷ 240
240 - 277
Star
380 ÷ 415
416 - 480
Star (50Hz)
690
Contact Marelli Motori
Contact Marelli Motori
690
355 MB (6 leads generator)
400 ÷ 630 (6 leads generators)
710* ÷ 900* (6 leads generators)
Star (60Hz)
*: For available voltage when operating at different frequency contact Marelli Motori.
Voltage at 60 Hz [V]
AVAILABLE VOLTAGES
Special voltages are available on request in accordance with the table below. Please contact Marelli Motori for further informations.
Frame Size
120V ÷ 380V
480V ÷ 690V
690V ÷ 1000V
1000V ÷ 7200V
7200V ÷ 11000V
11000V ÷ 15000V
160
200 ÷ 315
355
400
450
500 ÷ 630
710 ÷ 900
: Available voltage
: Not applicable (for further detail please contact Marelli Motori)
INSULATION, IMPREGNATION AND PROTECTIVE TREATMENT OF WINDING
For low voltage class H. For medium and high voltage class F . Windings are impregnated with high quality materials and using the latest technologies including
Vacuum Pressure Impregnation (VPI).
A further protective treatment is applied , making the generators suitable for tough environmental conditions. Special degrees of protection and tropicalization
are available on request.
WINDINGS
Generators up to frame 560 included for industrial application are constructed with 2/3 pitch winding to reduce the voltage harmonic content in applications
with non-linear loads. The no-load voltage waveform is sinusoidal with Total Harmonic Distortion (THD) content less than 2%.
RADIO INTERFERENCE
Marelli Generators are equipped with devices in order to Class B Group 1 radio interference as defined by EN55O11.
PROTECTION DEGREE
The standard protection degree is IP 23. Higher protection degrees are available on request for frame sizes 250 to 800 through the application of filter, air-to-air
or air-to-water heat exchanger up to IP 55.
VENTILATION AND DIRECTION OF ROTATION
Generators are axially self-cooled and can run in both directions of rotation.
Air inlet direction is:
• Frame size 160 : Radial
• Frame sizes 200 and higher: Axial + radial
ROTOR BALANCING
Rotors are dynamically balanced with a half key applied to the shaft extension in accordance with IEC 60034-14 to vibration grade normal A in standard
configuration. Generators can be supplied with special vibration levels on request.
VIBRATION
Vibration level is in accordance with ISO 10816. Measurement, evaluation and limits of vibration severity are in accordance with IEC 60034-14.
BEARINGS AND OVER SPEED
Oversized bearings. The permissible over speed is 1,5 times the rated speed (referred to 50 Hz).
Sleeve bearings from 400 to 900 frame sizes are available on request.
TESTING CAPABILITY
Marelli Motori has a high capability test room with the possibility of testing generators in their original mounting (vertical and horizontal) and for all designed
voltages (up to 15000 V) and power (up to 10 MVA).
Testing can be conducted at different frequency (50 Hz or 60 Hz) through a regenerative Active Front End System.
Testing is carried out in compliance with all major international standards (IEC, IEEE), customer specifications, marine/navy rules.
Overloads
During continuous duty (S1), the following overloads are allowed :
10% for 1 hour
15% for 10 minutes
30% for 4 minutes
50% for 2 minutes
These overloads must be occasional and followed by one hour of running at normal load or less.
Stand-by ratings are based on continuous supply of loads for any utility power failure.
No overloads are allowed in stand-by duty.
Single phase operation
Three phase (12-wire) wound generators can be reconnected and derated to 66% for single phase operation (with a zig-zag connection).
Otherwise generators with dedicated (4-wire) single phase windings can be supplied on request.
The following derating factors must be applied to the corresponding configurations
Connection
K factor (L - L)
K factor (L - N)
Star series
0,60
0,33
Delta series
0,50
-
Star parallel
0,60
0,33
Zig - zag
0,66
0,33
Parallel operation
All generators are provided with a amply sized damper cage and are suitable for parallel operation with other generators, when equipped with the paralleling unit.
A power factor regulator is available on request.
No-Load operation at reduced speed
All regulators work to reduce the excitation current in order to protect the excitation system when the generator is being used at reduced speed.
Transient ratings
The voltage drop due to the application of full load at 0,8 power factor inductive on industrial 160 ÷ 400 frame size generators varies between 16% and 20% of
the rated voltage: the output voltage recovers to within 3% of the rated value in less than 0,3 seconds.
Altitude
The rated outputs refer to installation up to 1.000 m a.s.l. Above this level the following derating factors must be applied.
Altitude (m asl)
< 1.000
< 1.500
< 2.000
< 2.500
< 3.000
K Factor
1,00
0,96
0,93
0,90
0,86
Ambient temperature
The rated outputs given in this catalogue are based on a maximum ambient temperature of 40 °C.
When operating at different ambient temperatures the output rating can be obtained by applying the factors as in the following table.
Ambient Temperature
[°C]
30
35
40
45
50
55
K Factor
1.04
1,00
1,00
0,96
0,93
0,9
Power factor
The nominal power factor is 0,8 lagging.
For different power factor values the following derating factors must be applied.
Power Factor
1
0,8
0,7
0,6
0,5
0,3
0
K Factor
1,00
1,00
0,93
0,88
0,84
0,82
0,80
Special configurations
The following derating factors must be applied to the corresponding configurations
Special configuration
Air to air heat exchanger
Air to water heat exchanger1
Inlet filters
IP43 inlet and outlet filters
IP44 inlet and outlet filters
K Factor
0,70
0,90
0,92
0,85
0,80
: for marine application refer to MJRM series
1
EXCITATION SYSTEM
The generators are self-exciting, by means of a brushless type excitation system.
The voltage is maintained within ±0,5% of the nominal value in steady state condition with a balanced and non distorting load.
Auxiliary winding
The excitation system of generators from frame size 200 to 450 is fed by an auxiliary winding which gives a better response to the variation in loads and
sustains the power supply in the case of a short-circuit. Auxiliary winding on the 160 frame is available on request.
Permanent Magnet Generators (PMG)
The generators from frame size 225 mm and larger can be supplied with a Permanent Magnet Generator (PMG) if required, which gives an independent supply
to the excitation system. PMG is advisable for use with generators in particular applications such as unbalanced loads and distorting loads.
Manual voltage regulation
Available within ±5% of the rated value by means of a potentiometer placed inside the voltage regulator. A remote voltage setting is possible by means of an
external potentiometer, which can be supplied on request.
Over-excitation protection
Generators from frame sizes 160 to 450 are equipped with adjustable over-excitation protection which will protect the alternator in the event of over excitation
when combined with an external protection system.
THREE PHASE SHORT CIRCUIT CURRENT
Generators with auxiliary windings or PMG ensure a three phase short-circuit current (Icc) higher than 3 times the rated current (In): Icc > 3 In.
Generators from 500 frame size are supplied with an over excitation device which ensures a three phase short circuit current higher than 3 times the rated
current.
AUTOMATIC VOLTAGE REGULATOR (AVR) SPECIFICATIONS
The generators are equipped with the following AVR set.
Generator
frame size
MARK V
MARK I
ANALOGUE
MGC I
MGC II
MARK X
DIGITAL
MEC 100 series
M16FA655A
M40FA640A
M40FA610A
M63FA310A
M40FA644A
Standard
160 ÷ 250
315 ÷ 450
500 ÷ 560
630 ÷ 800
-
-
On request
-
160 ÷ 250 and
500 ÷ 630
-
-
225 ÷ 560
400 ÷ 900
Single phase
Three phase
AVR supply
Voltage sensing
Auxiliary winding*, mains
PMG
Single phase
Voltage remote control
M71FA310A
M710FA320A
Auxiliary winding, mains, PMG
Three phase
Arrangement
Radio interference suppressor
Internal
Arrangement for external filter
Over-excitation device
-
Parallel operation with the mains
-
Arrangement for external device
Internal
Parallel operation with similar
generators
-
Arrangement
Internal
-
Field over-current,
Field over-voltage,
Generator over/under voltage,
Generator over-current,
Loss of sensing
Standard
protections
Arrangement for VARICOMP
Over-excitation
Limiters
Functions
Over-excitation
Under-frequency,
Over/under-excitation
Under-frequency
-
Auxiliary inputs
PC interface,
Soft start,
Auxiliary inputs,
Contact inputs,
PC interface,
Soft start,
Auxiliary inputs,
Contact inputs,
DMS
*: Auxiliary winding on the 160 frame is available on request.
Analogue AVR (MARK and MGC series)
The voltage regulators are the standard features for synchronous generators of MarelliMotori. These regulators are suitable for low and medium voltage
machines. The regulators are fully insulated in order to maintain high reliability also with severe ambient conditions (high level of humidity, dust, salt
atmosphere), and in case of high vibrations level. The regulators can work both for single and 3-phase operations.
Digital AVR (MEC100 series)
MEC100 series regulators are microprocessor-based devices for the excitation control of MarelliMotori synchronous generators.
The full-function and full-protection control system ensures high performances with suitable accuracy in a wide range of applications.
A proprietary user-friendly software is provided with the equipment for commissioning and monitoring purposes.
The MEC100 series includes models with embedded optional features like the Diode Monitoring functions.
The MEC100 complies also with the DNV rules.
Other AVRs may be installed on request.
Type
Leads
400V / 50Hz
Power rating [kVA]
Continuous duty
Stand by
125/40 105/40 80/40 163/27 150/40
ΔT cl. H
4 poles
ΔT cl. F
ΔT cl. B
Efficiency
4/4
pf = 0,8
125/40
[%]
400 V @ 50 Hz - 1500 rpm
480V / 60Hz
Power rating [kVA]
Continuous duty
Stand by
125/40 105/40 80/40 163/27 150/40
ΔT cl. H
ΔT cl. F
ΔT cl. B
Efficiency
4/4
pf = 0,8
125/40
Inertia
B3
Weight
B3
Approx.
J
Approx.
[%]
[kg m2]
[kg]
480V @ 60Hz - 1800 rpm
IP23
MJB 160 SA4
MJB 160 SB4
MJB 160 SC4
MJB 160 MA4
MJB 160 MB4
12
12
12
12
12
17,0
20,0
23,0
28,0
32,0
15,6
18,4
21,1
25,7
29,4
13,6
16,0
18,4
22,4
25,6
18,7
22,0
25,3
30,8
35,2
18,0
21,2
24,4
29,7
33,9
85,6
87,4
87,5
88,2
88,3
21,4
24,7
29,9
34,2
40,0
19,6
22,6
27,4
31,4
36,7
17,1
19,8
23,9
27,4
32,0
23,5
27,2
32,9
37,6
44,0
22,7
26,2
31,7
36,3
42,4
86,4
88,2
88,3
89,2
89,1
0,11
0,12
0,14
0,16
0,17
120
130
140
165
175
MJB 200 SA4
MJB 200 SB4
MJB 200 MA4
MJB 200 MB4
12
12
12
12
42,0
48,0
62,0
72,0
38,5
44,0
57,0
66,0
33,6
38,4
49,6
57,6
46,2
52,8
68,2
80,0
44,5
50,9
65,7
76,5
88,5
88,7
90,1
90,5
51,0
59,5
76,0
87,0
46,8
54,6
69,7
79,8
40,8
47,6
60,8
69,6
56,1
65,4
83,6
96,5
54,1
63,1
80,6
92,0
89,5
89,3
90,7
90,9
0,28
0,30
0,36
0,43
215
220
260
300
MJB 225 SA4
MJB 225 SB4
MJB 225 MA4
MJB 225 LA4
12
12
12
12
85,0
92,0
105
132
78,0
84,4
96,2
121
68,0
73,6
84,0
106
93,5
101
116
145
90,1
97,5
111
140
91,0
91,5
91,8
92,2
108
114
131
158
98,7
104
120
145
86,1
90,9
105
127
118
125
144
174
114
120
139
168
91,5
92,0
92,6
93,0
0,63
0,70
0,79
0,92
345
350
390
420
MJB 250 MA4
MJB 250 MB4
MJB 250 LA4
MJB 250 LB4
12
12
12
12
165
185
220
250
150
170
200
230
132
150
175
200
180
205
240
275
175
195
235
265
92,9
93,0
93,2
93,4
205
230
270
300
190
215
250
275
164
184
216
240
225
255
295
330
215
245
285
320
93,6
93,6
93,9
93,9
1,4
1,7
1,9
2,1
530
590
660
710
MJB 315 SA4
MJB 315 SB4
MJB 315 MA4
MJB 315 MB4
12
12
12
12
300
350
410
450
275
320
375
415
240
280
330
360
330
385
450
500
320
370
435
475
93,1
93,4
93,7
94,0
370
425
500
550
340
390
460
505
296
340
400
440
405
470
550
610
390
450
530
585
93,8
94,0
94,2
94,8
3,7
4,2
4,8
5,7
830
920
1060
1200
MJB 355 SA4
MJB 355 SB4
MJB 355 MA4
MJB 355 MB4
12
12
12
6
510
570
680
800
470
520
625
730
410
455
545
640
560
625
750
880
540
605
720
850
94,0
94,6
94,7
95,0
625
695
825
960
575
640
760
880
500
556
660
768
690
765
910
1055
665
735
875
1020
94,5
95,1
95,1
95,3
8,0
9,3
11,7
13,1
1250
1550
1800
2050
MJB 400 MA4
MJB 400 MB4
MJB 400 LA4
MJB 400 LB4
6
6
6
6
930
1050
1150
1300
850
960
1055
1190
745
840
920
1040
1025
1155
1265
1430
985
1115
1220
1380
95,2
95,3
95,6
95,8
1175
1320
1420
1625
1080
1210
1305
1490
940
1056
1136
1300
1295
1450
1560
1790
1245
1400
1505
1725
95,7
95,7
96,0
96,3
16,3
17,0
19,3
22,5
2250
2300
2550
2800
MJB 450 MB4
MJB 450 LA4
MJB 450 LB4
6
6
6
1500
1650
1875
1375
1510
1720
1200
1320
1500
1650
1815
2065
1590
1750
1990
95,9
96,0
96,2
1800
1980
2250
1650
1815
2065
1440
1584
1800
1980
2180
2475
1910
2100
2385
96,3
96,3
96,4
29,0
34,0
38,0
3200
3600
4000
MJB 500 SC4
MJB 500 MB4
MJB 500 LA4
6
6
6
2000
2200
2500
1835
2020
2290
1600
1760
2000
2200
2420
2750
2120
2330
2650
96,1
96,2
96,4
2400
2640
3000
2200
2420
2750
1920
2112
2400
2640
2905
3300
2545
2800
3180
96,5
96,5
96,7
46,7
52,5
61,5
4000
4400
5100
MJB 560 MA4
MJB 560 LA4
6
6
2650
3200
2430
2935
2120
2560
2915
3520
2810
3390
96,4
96,5
3050
3680
2800
3375
2440
2945
3355
4050
3235
3900
96,5
96,6
83,0
95,0
5200
6300
MJB 630 MB41
MJB 630 LA41
6
6
3300
3600
3025
3300
2640
2880
3565
3890
3465
3780
96,4
96,5
3795
4140
3480
3795
3040
3315
4100
4470
3985
4345
96,7
96,8
140
158
7500
8000
MJB 710 SC42
MJB 710 MB42
6
6
4000
4300
3670
3940
3200
3440
4320
4645
4200
4515
96,2
96,4
4400
4730
4035
4340
3520
3785
4750
5110
4620
4965
96,5
96,7
on request on request
: 690 V recommended
: 690 V only. For different voltage please contact MarelliMotori. These generators are dedicated for 50 Hz or 60 Hz. For available voltage and performance when operating at different frequency contact MarelliMotori.
Ratings refer to following conditions: balanced non-deforming load, altitude 1000 m a.s.l., minimum power factor 0,8.
1
2
Type
Leads
6 poles
400V / 50Hz
Power rating [kVA]
Continuous duty
125/40
105/40
80/40
ΔT cl. H
ΔT cl. F
ΔT cl. B
Efficiency
4/4
pf = 0,8
125/40
[%]
400 V @ 50 Hz - 1000 rpm
480V / 60Hz
Power rating [kVA]
Continuous duty
125/40
105/40
80/40
ΔT cl. H
ΔT cl. F
ΔT cl. B
Efficiency
4/4
pf = 0,8
125/40
[%]
Inertia
B3
Weight
B3
Approx.
J
[kg m2]
Approx.
480 V @ 60 Hz - 1200 rpm
[kg]
IP23
MJB 400 SA6
MJB 400 SB6
MJB 400 SC6
MJB 400 MA6
MJB 400 MB6
MJB 400 LA6
MJB 400 LB6
6
6
6
6
6
6
6
400
450
500
620
700
800
970
365
410
460
570
640
735
890
320
360
400
500
560
640
780
92,7
93,0
93,7
94,1
94,3
94,6
94,8
500
565
625
775
875
1000
1215
460
520
575
715
805
920
1120
400
455
500
620
700
800
975
93,0
93,4
94,0
94,4
94,6
94,9
95,1
11,8
14,1
16,8
17,9
19,4
20,9
24,2
1450
1600
1800
2000
2260
2530
2750
MJB 450 MB6
MJB 450 LA6
MJB 450 LB6
6
6
6
1040
1200
1360
950
1100
1250
835
960
1090
94,6
95,2
95,4
1300
1500
1700
1200
1380
1560
1040
1200
1360
95,5
95,7
95,6
49,9
55,0
61,4
3200
3600
3900
MJB 500 MA6
MJB 500 MB6
MJB 500 MC6
MJB 500 LA6
6
6
6
6
1400
1540
1600
1680
1275
1400
1465
1530
1120
1235
1280
1345
95,1
95,2
95,2
95,4
1750
1925
2000
2100
1600
1770
1840
1930
1400
1540
1600
1680
95,7
95,8
95,8
96,0
64,7
73,6
80,2
88,9
4150
4600
4900
5300
MJB 560 SC6
MJB 560 MA6
MJB 560 LA6
6
6
6
1870
2080
2360
1700
1900
2150
1500
1665
1890
95,9
96,0
96,2
2150
2400
2700
1980
2200
2480
1720
1920
2160
96,4
96,5
96,7
115
115
135
4900
5400
6500
MJB 630 SD6
MJB 630 MA6
MJB 630 MC6
6
6
6
2450
2750
3000
2250
2500
2750
1960
2200
2400
95,7
95,7
96,0
2740
3100
3350
2520
2850
3100
2195
2480
2680
96,2
96,2
96,4
170
190
210
6900
7900
8100
MJB 710 SC61
MJB 710 MA61
6
6
3500
3800
3200
3500
2800
3040
96,0
96,7
3850
4180
3550
3850
3080
3345
96,5
96,7
on request
on request
on request
on request
8 poles
400 V @ 50 Hz - 750 rpm
480 V @ 60 Hz - 900 rpm
IP23
MJB 400 SA8
MJB 400 SB8
MJB 400 SC8
MJB 400 MA8
MJB 400 MB8
MJB 400 LA8
MJB 400 LB8
6
6
6
6
6
6
6
240
310
360
430
510
600
740
220
285
330
395
465
550
680
195
250
290
345
410
480
595
91,5
92,0
92,3
92,5
93,0
93,2
93,5
300
400
450
540
640
750
925
275
365
410
495
585
685
850
240
320
360
435
515
600
740
92,0
92,5
92,8
93,0
93,5
93,7
94,0
13,5
16,2
19,1
20,6
22,4
24,1
25,4
1450
1600
1800
2000
2260
2530
2750
MJB 500 SA8
MJB 500 SC8
MJB 500 MB8
MJB 500 LA8
6
6
6
6
820
1020
1270
1400
750
935
1165
1275
660
820
1020
1120
94,5
95,0
95,1
95,2
1025
1275
1590
1680
940
1170
1455
1530
820
1020
1275
1345
95,1
95,5
95,6
95,9
55,1
74,2
82,2
95,0
3200
3800
4700
5400
MJB 560 SC8
MJB 560 MB8
MJB 560 LA8
6
6
6
1480
1750
2025
1350
1600
1850
1185
1400
1620
95,4
95,6
95,9
1775
2075
2400
1620
1900
2200
1420
1660
1920
95,8
95,9
96,1
115
130
155
5100
5700
6700
MJB 630 MC8
MJB 630 LA8
6
6
2200
2450
2000
2250
1760
1960
95,5
96,1
2350
2820
2150
2580
1880
2260
96,2
96,5
195
240
8300
9200
MJB 710 SA81
MJB 710 SC81
MJB 710 MA81
MJB 710 MB81
6
6
6
6
2750
3100
3600
3700
2500
2850
3300
3400
2200
2480
2880
3000
96,2
96,5
96,6
96,7
2850
3250
3750
4000
2600
3000
3450
3750
2280
2600
3000
3200
96,5
96,8
96,9
96,9
on request
on request
on request
on request
on request
on request
on request
on request
10 poles
400 V @ 50 Hz - 600 rpm
480 V @ 60 Hz - 720 rpm
IP23
MJB 500 SA10
MJB 500 SC10
MJB 500 MB10
MJB 500 LA10
6
6
6
6
595
745
870
965
550
685
800
885
480
600
700
775
93,9
94,2
94,7
95,0
740
935
1050
1210
680
860
965
1110
595
750
840
970
94,4
94,7
95,2
95,5
63,8
81,6
89,7
106
3300
3900
4800
5600
MJB 630 SC10
MJB 630 MA10
MJB 630 MB10
MJB 630 LA10
6
6
6
6
1200
1430
1690
1750
1100
1320
1550
1600
960
1145
1355
1400
95,0
95,4
95,5
95,7
1380
1650
1945
2010
1260
1510
1780
1840
1105
1320
1560
1610
95,5
95,9
96,0
96,2
180
200
230
260
7300
8500
8700
9400
MJB 710 SC101
MJB 710 MA101
MJB 710 MB101
MJB 710 LB101
6
6
6
6
2470
2960
3160
3420
2270
2715
2900
3130
1980
2370
2530
2740
96,2
96,4
96,4
96,6
2770
3320
3550
3825
2530
3050
3250
3510
2220
2660
2840
3060
96,4
96,6
96,6
96,8
on request
on request
on request
on request
on request
on request
on request
on request
: 690 V recommended. These generators are dedicated for 50 Hz or 60 Hz. For available voltage and performance when operating at different frequency contact MarelliMotori.
1
3000V / 50Hz
Type
Leads
105/40
ΔT cl. F
4 poles
6000V / 50Hz
Power rating [kVA]
Continuous duty
80/40
105/40
80/40
ΔT cl. B
ΔT cl. F
ΔT cl. B
3000 V - 6000 V @ 50 Hz - 1500 rpm
4160V / 60Hz
105/40
ΔT cl. F
4160 V - 6600 V @ 60 Hz - 1800 rpm
IP23
MJH 400 MA4
MJH 400 LA4
MJH 400 LB4
6
6
6
600
840
1020
520
730
890
550
740
920
480
650
810
700
960
1180
610
840
1030
660
900
1120
575
785
975
MJH 450 MB4
MJH 450 LA4
MJH 450 LB4
6
6
6
1050
1200
1300
910
1040
1130
1000
1120
1250
870
970
1090
1130
1250
1400
980
1090
1220
1100
1200
1330
960
1045
1160
MJH 500 MA4
MJH 500 MB4
MJH 500 LA4
MJH 500 LB4
6
6
6
6
1450
1700
1850
1950
1260
1480
1610
1700
1350
1500
1750
1900
1170
1300
1520
1650
1660
2000
2150
2250
1440
1740
1870
1960
1500
1650
1900
2200
1305
1440
1655
1915
MJH 560 MA4
MJH 560 LA4
MJH 560 LB4
6
6
6
2300
2550
2800
2000
2220
2440
2250
2450
2750
1960
2130
2400
2450
2800
3050
2130
2440
2650
2500
2750
3000
2175
2395
2610
MJH 630 MB4
MJH 630 LA4
MJH 630 LB4
6
6
6
2900
3200
3600
2520
2780
3130
2900
3200
3550
2520
2750
3090
3150
3500
3700
2750
2050
3220
3150
3500
3700
2745
3045
3220
MJH 710 SC4
MJH 710 MB4
MJH 710 LA4
MJH 710 LB4
6
6
6
6
4200
4800
5500
6000
3650
4180
4780
5220
4200
4800
5500
6000
3650
4180
4780
5220
4500
5000
5800
6600
3920
4350
5050
5750
4500
5000
5800
6600
3920
4350
5050
5750
MJH 800
6
9000
7830
9000
7830
on request
on request
on request
on request
6 poles
3000 V - 6000 V @ 50 Hz - 1000 rpm
4160 V - 6600 V @ 60 Hz - 1200 rpm
IP23
MJH 400 LA6
MJH 400 LB6
MJH 450 MB6
MJH 450 LA6
MJH 450 LB6
6
6
6
6
6
620
660
680
750
840
540
575
590
655
735
540
570
515
650
730
470
500
780
570
640
710
760
680
860
970
620
665
715
750
845
650
700
625
800
890
570
610
MJH 500 MA6
MJH 500 MB6
MJH 500 LA6
6
6
6
930
1100
1240
810
960
1080
800
960
1100
700
840
960
1070
1270
1430
935
1105
1245
970
1160
1330
845
1010
1160
MJH 560 SC6
MJH 560 MB6
MJH 560 LA6
6
6
6
1620
1950
2150
1410
1700
1875
1500
1800
2000
1305
1570
1740
1800
2100
2200
1570
1830
1915
1680
2000
2050
1465
1740
1785
MJH 630 MA6
MJH 630 LA6
MJH 630 LB6
6
6
6
2250
2500
2700
1960
2175
2350
2100
2300
2500
1830
2005
2175
2300
2600
2700
2005
2265
2350
2150
2350
2500
1875
2045
2175
MJH 710 SC6
MJH 710 MA6
MJH 710 MB6
MJH 710 LA6
MJH 710 LB6
6
6
6
6
6
3450
4250
4650
4850
5150
3005
3700
4050
4220
4485
3300
4100
4500
4700
5000
2875
3570
3915
4090
4350
3500
4300
4700
4900
5200
3045
3745
4090
4265
4525
3350
4100
4500
4700
5000
2915
3570
3915
4090
4350
MJH 800 MA6
MJH 800 MB6
MJH 800 LA6
MJH 800 LB6
6
6
6
6
6100
6800
7400
8000
5310
5920
6440
6960
6000
6700
7400
8000
5220
5830
6440
6960
6200
6800
7500
8000
5395
5920
6525
6960
6100
6700
7500
8000
5310
5830
6525
6960
All generators are dedicated for 50 Hz or 60 Hz.
MJH 900
10
6600V / 60Hz
Power rating [kVA]
Continuous duty
80/40
105/40
80/40
ΔT cl. B
ΔT cl. F
ΔT cl. B
For available power and speed contact Marelli Motori
700
775
3000V / 50Hz
Type
Leads
105/40
ΔT cl. F
8 poles
6000V / 50Hz
Power rating [kVA]
Continuous duty
80/40
105/40
80/40
ΔT cl. B
ΔT cl. F
ΔT cl. B
3000 V - 6000 V @ 50 Hz - 750 rpm
4160V / 60Hz
105/40
ΔT cl. F
6600V / 60Hz
Power rating [kVA]
Continuous duty
80/40
105/40
80/40
ΔT cl. B
ΔT cl. F
ΔT cl. B
4160 V - 6600 V @ 60 Hz - 900 rpm
IP23
MJH 400 LA8
MJH 400 LB8
6
6
440
510
385
445
380
440
335
385
510
585
445
510
470
540
410
470
MJH 500 MA8
MJH 500 MB8
MJH 500 LA8
MJH 500 LB8
6
6
6
6
780
920
1050
1150
680
805
915
1005
680
790
920
1050
595
690
805
915
900
1060
1220
1300
785
925
1065
1135
820
970
1100
1200
715
845
960
1045
MJH 560 MB8
MJH 560 LA8
6
6
1350
1550
1175
1350
1250
1440
1090
1255
1550
1720
1350
1500
1500
1650
1305
1440
MJH 630 MB8
MJH 630 LA8
MJH 630 LB8
6
6
6
1750
1850
2000
1525
1610
1740
1600
1700
1800
1395
1480
1570
1840
1950
2120
1600
1700
1850
1750
1850
2000
1525
1610
1740
MJH 710 SA8
MJH 710 SC8
MJH 710 MA8
MJH 710 MB8
MJH 710 LB8
6
6
6
6
6
2600
3200
3900
4350
4600
2265
2785
3395
3785
4005
2400
3000
3750
4200
4500
2090
2610
3265
3655
3915
2730
3330
4150
4600
4750
2380
2900
3620
4000
4140
2600
3200
4000
4500
4650
2260
2780
3480
3910
4050
MJH 800 MB8
MJH 800 LA8
6
6
4900
5800
4265
5050
4800
5700
4180
4960
5100
6100
4440
5300
5000
6000
4350
5200
10 poles
3000 V - 6000 V @ 50 Hz - 600 rpm
4160 V - 6600 V @ 60 Hz - 720 rpm
IP23
MJH 500 SA10
MJH 500 MA10
MJH 500 MB10
MJH 500 LA10
6
6
6
6
460
560
660
730
400
490
575
640
400
480
570
650
350
420
500
570
530
650
760
850
460
570
660
740
470
580
690
760
410
500
600
660
MJH 630 SA10
MJH 630 MA10
MJH 630 MB10
MJH 630 LA10
MJH 630 LB10
6
6
6
6
6
950
1100
1300
1500
1700
830
960
1130
1300
1480
900
1000
1200
1350
1450
780
870
1050
1170
1260
1030
1200
1400
1600
1800
900
1050
1220
1400
1570
970
1130
1350
1500
1700
850
980
1170
1300
1480
MJH 710 SA10
MJH 710 MA10
MJH 710 LA10
MJH 710 LB10
6
6
6
6
2000
2400
2700
3400
1740
2090
2350
2960
1800
2200
2400
3200
1570
1920
2100
2780
2100
2500
2800
3740
1830
2170
2440
3250
1950
2350
2640
3520
1700
2050
2300
3060
MJH 800 SA10
MJH 800 MA10
MJH 800 LA10
6
6
6
3700
4100
4800
3220
3570
4180
3500
3900
4500
3050
3400
3920
4000
4500
5250
3480
3900
4570
3800
4280
4900
3300
3730
4260
MJH 900
11
Type
Leads
4 poles
11000V / 50Hz
Power rating [kVA]
Continuous duty
105/40
80/40
ΔT cl. F
ΔT cl. B
11000 V @ 50 Hz - 1500 rpm
13800V / 60Hz
Power rating [kVA]
Continuous duty
105/40
80/40
ΔT cl. F
ΔT cl. B
13800 V @ 60 Hz - 1800 rpm
MJH 450 LA4
6
900
780
-
-
MJH 500 MA4
MJH 500 LA4
MJH 560 MA4
MJH 560 LA4
6
6
6
6
1300
1500
1850
2100
1130
1300
1610
1830
1400
1600
2000
2250
1220
1395
1740
1960
MJH 630 SC4
MJH 630 MA4
MJH 630 LB4
6
6
6
2500
2850
3250
2175
2480
2830
2700
3000
3400
2350
2610
2960
MJH 710 SC4
MJH 710 MA4
MJH 710 LB4
6
6
6
3600
4600
5500
3130
4000
4780
4000
5250
5500
3480
4570
4785
MJH 800 MA4
6
9000
7830
on request
on request
6 poles
11000 V @ 50 Hz - 1000 rpm
13800 V @ 60 Hz - 1200 rpm
IP23
MJH 450 LA6
MJH 450 LB6
6
6
560
620
490
540
-
-
MJH 500 MA6
MJH 500 MB6
MJH 500 LA6
6
6
6
680
820
950
600
715
830
820
980
1150
720
860
1000
MJH 560 MB6
MJH 560 LA6
6
6
1450
1650
1270
1440
1700
1900
1480
1650
MJH 630 MB6
MJH 630 MC6
6
6
1700
2000
1480
1740
1950
2150
1700
1875
MJH 710 SC6
MJH 710 MA6
MJH 710 MB6
MJH 710 LA6
MJH 710 LC6
6
6
6
6
6
2600
3000
3600
4000
4500
2270
2610
3130
3480
3920
2750
3150
3750
4250
4600
2400
2750
3260
3700
4000
MJH 800 MA6
MJH 800 MB6
MJH 800 LA6
MJH 800 LB6
6
6
6
6
5500
6000
6600
7000
3490
5220
5740
6100
5750
6300
6800
7200
5000
5480
5920
6260
MJH 900
12
IP23
Type
Leads
8 poles
11000V / 50Hz
Power rating [kVA]
Continuous duty
105/40
80/40
ΔT cl. F
ΔT cl. B
11000 V @ 50 Hz - 750 rpm
13800V / 60Hz
Power rating [kVA]
Continuous duty
105/40
80/40
ΔT cl. F
ΔT cl. B
13800 V @ 60 Hz - 900 rpm
IP23
MJH 500 SA8
MJH 500 MA8
MJH 500 MB8
MJH 500 LA8
6
6
6
6
480
580
680
780
420
500
600
680
570
690
820
930
500
605
715
810
MJH 560 MB8
MJH 560 LA8
6
6
1100
1250
960
1090
1200
1300
1050
1130
MJH 630 MC8
MJH 630 LA8
MJH 630 LB8
6
6
6
1350
1500
1650
1170
1300
1440
1450
1600
1750
1260
1400
1520
MJH 710 SA8
MJH 710 SC8
MJH 710 MA8
MJH 710 MB8
MJH 710 LB8
6
6
6
6
6
1900
2400
3000
3500
3700
1660
2090
2610
3050
3220
2000
2500
3150
3900
4100
1740
2170
2750
3400
3570
MJH 800 MB8
MJH 800 LA8
MJH 800 LB8
6
6
6
4000
4400
5500
3480
3830
4780
4300
4700
5700
3740
4090
4960
10 poles
11000 V @ 50 Hz - 600 rpm
13800 V @ 60 Hz - 720 rpm
IP23
MJH 500 SA10
MJH 500 MA10
MJH 500 MB10
MJH 500 LA10
6
6
6
6
340
410
490
550
300
360
430
480
400
490
580
650
350
430
500
570
MJH 630 SA10
MJH 630 MA10
MJH 630 MB10
MJH 630 LA10
MJH 630 LB10
6
6
6
6
6
760
850
1050
1130
1230
660
740
910
980
1070
830
960
1140
1280
1450
725
840
990
1110
1260
MJH 710 SA10
MJH 710 MA10
MJH 710 LA10
MJH 710 LB10
6
6
6
6
1530
1870
2050
2700
1330
1630
1780
2350
1660
2000
2240
2950
1440
1740
1950
2570
MJH 800 SA10
MJH 800 MA10
MJH 800 LA10
6
6
6
3300
3700
4200
2870
3220
3650
3250
3650
4100
2830
3180
3570
MJH 900
13
Type
Leads
4 poles
380V to 690V/ 50Hz
Power rating [kVA]
Continuous duty
95/50
70/50
ΔT cl. F
ΔT cl. B
Efficiency
4/4
pf = 0,8
95/50
[%]
380 V to 690 V @ 50 Hz - 1500 rpm
380V to 690V / 60Hz
Power rating [kVA]
Continuous duty
95/50
70/50
ΔT cl. F
ΔT cl. B
Efficiency
4/4
pf = 0,8
95/50
[%]
Inertia
B3
Weight
B3
Approx.
J
[kg m2]
Approx.
380 V to 690 V @ 60 Hz - 1800 rpm
[kg]
IP23
MJBM 160 SA4
MJBM 160 SB4
MJBM 160 SC4
MJBM 160 MA4
MJBM 160 MB4
12
12
12
12
12
14,8
17,4
20,1
24,4
27,9
12,7
14,9
17,3
20,9
23,9
80,9
82,3
83,9
85,5
86,1
17,6
20,5
24,1
28,9
33,5
15,1
17,6
20,7
24,8
28,7
81,4
82,5
83,9
86,0
86,7
0,11
0,12
0,14
0,16
0,17
120
130
140
165
175
MJBM 200 SA4
MJBM 200 SB4
MJBM 200 MA4
MJBM 200 MB4
12
12
12
12
36,5
42,0
54,0
63,0
31,3
36,1
46,4
54,1
86,0
87,2
88,3
89,5
44,5
52,0
64,0
76,0
38,2
44,6
54,9
65,2
86,7
87,3
88,4
89,6
0,28
0,30
0,36
0,43
215
220
260
300
MJBM 225 SA4
MJBM 225 SB4
MJBM 225 MA4
MJBM 225 LA4
12
12
12
12
74,0
80,0
92,0
115
65,0
70,0
85,0
105
89,0
89,4
90,2
91,2
91,0
99,0
112
136
78,0
85,0
96,0
117
89,2
89,5
90,4
91,3
0,63
0,70
0,79
0,92
345
350
390
420
MJBM 250 MA4
MJBM 250 MB4
MJBM 250 LA4
MJBM 250 LB4
12
12
12
12
145
160
190
220
130
140
170
195
91,8
92,1
92,3
92,6
165
190
220
245
145
165
190
215
92,3
92,5
92,7
92,8
1,4
1,7
1,9
2,1
530
590
660
710
MJBM 315 SA4
MJBM 315 SB4
MJBM 315 MA4
MJBM 315 MB4
12
12
12
12
260
305
355
390
230
270
310
340
92,0
92,5
93,1
93,5
310
355
420
460
270
305
365
395
92,6
93,2
93,7
94,2
3,7
4,2
4,8
5,7
830
920
1060
1200
MJBM 355 SA4
MJBM 355 SB4
MJBM 355 MA4
MJBM 355 MB4
12
12
12
6
445
495
595
695
390
435
520
605
93,6
93,9
94,5
94,8
515
590
690
815
445
510
600
700
94,0
94,5
94,9
95,1
8,0
9,3
11,7
13,1
1250
1550
1800
2050
MJBM 400 MA4
MJBM 400 MB4
MJBM 400 LA4
MJBM 400 LB4
MJBM 400 LC4
6
6
6
6
6
810
915
1005
1135
1160
705
800
875
990
1010
94,8
95,2
95,3
95,6
95,8
975
1090
1205
1345
1400
840
940
1035
1155
1220
95,0
95,4
95,6
95,8
96,0
16,3
17,0
19,3
22,5
23,7
2250
2300
2550
2800
3000
MJBM 450 MB4
MJBM 450 LA4
MJBM 450 LB4
6
6
6
1310
1440
1635
1140
1255
1425
95,6
96,6
96,8
1505
1655
1875
1310
1440
1630
96,4
96,8
97,0
29,0
34,0
38,0
3200
3600
4000
MJBM 500 SC4
MJBM 500 MA4
MJBM 500 MB4
MJBM 500 MC4
MJBM 500 LA4
MJBM 500 LB4
6
6
6
6
6
6
1740
1800
1930
2000
2200
2200
1515
1570
1680
1740
1915
1915
95,7
95,7
95,9
96,0
96,1
96,2
2100
2200
2250
2360
2730
2730
1830
1910
1960
2060
2380
2380
95,9
96,0
96,1
96,2
96,3
96,4
46,7
50,5
52,5
54,3
61,5
63,5
4000
4200
4400
4600
5100
5200
MJBM 560 MA4
MJBM 560 LA4
6
6
2450
2950
2135
2570
96,3
96,5
2750
3300
2390
2875
96,5
96,6
83,0
95,0
5200
6300
MJBM 630 SC41
MJBM 630 MB41
MJBM 630 LA41
6
6
6
2700
3050
3500
2350
2655
3045
96,4
96,5
96,6
3000
3300
3700
2610
2875
3220
96,5
96,6
96,7
117
140
158
6700
7500
8000
MJBM 710 SC42
MJBM 710 MB42
6
6
3680
3950
3205
3440
96,3
96,5
4050
4350
3520
3780
96,4
96,6
MJBM 800
: 690 V recommended.
2
Ratings refer to following conditions: balanced non-deforming load, minimum power factor 0,8. For pitch winding details contact Marelli Motori.
1
MJBM 900
14
Type
Leads
6 poles
380V to 690V/ 50Hz
Power rating [kVA]
Continous duty
95/50
70/50
ΔT cl. F
ΔT cl. B
Efficiency
4/4
pf = 0,8
95/50
[%]
380 V to 690 V @ 50 Hz - 1000 rpm
380V to 690V / 60Hz
Power rating [kVA]
Continous duty
95/50
70/50
ΔT cl. F
ΔT cl. B
Efficiency
4/4
pf = 0,8
95/50
[%]
Inertia
B3
Weight
B3
Approx.
J
[kg m˛]
Approx.
380 V to 690 V @ 60 Hz - 1200 rpm
[kg]
IP23
MJBM 400 SA6
MJBM 400 SB6
MJBM 400 SC6
MJBM 400 MA6
MJBM 400 MB6
MJBM 400 LA6
MJBM 400 LB6
6
6
6
6
6
6
6
350
390
435
540
610
700
845
305
340
380
470
535
610
740
92,7
93,0
93,7
94,1
94,3
94,6
94,8
415
465
515
640
725
825
1000
360
400
445
550
625
710
860
92,9
93,9
93,9
94,3
94,5
94,8
95,0
11,8
14,1
16,8
17,9
19,4
20,9
24,2
1450
1600
1800
2000
2260
2530
2750
MJBM 450 MB6
MJBM 450 LA6
MJBM 450 LB6
6
6
6
890
1040
1180
775
905
1030
94,6
95,2
95,4
1050
1230
1400
915
1075
1220
95,1
95,7
95,9
49,9
55,0
61,4
3200
3600
3900
MJBM 500 SC6
MJBM 500 MA6
MJBM 500 MB6
MJBM 500 MC6
MJBM 500 LA6
6
6
6
6
6
1200
1300
1400
1450
1680
1045
1135
1220
1265
1465
95,0
95,2
95,2
95,3
95,4
1450
1600
1700
1800
2000
1265
1395
1480
1570
1740
95,5
95,1
95,2
95,2
95,4
64,7
64,7
73,6
80,2
88,9
3800
4150
4600
4900
5100
MJBM 560 MA6
MJBM 560 LA6
6
6
1800
2000
1570
1740
96,0
96,2
2050
2400
1785
2090
96,0
96,2
115
135
5400
6500
MJBM 630 SB6
MJBM 630 SC6
MJBM 630 MA6
MJBM 630 MB6
MJBM 630 LA6
MJBM 630 LB6
6
6
6
6
6
6
2100
2200
2400
2500
2700
2900
1830
1915
2090
2175
2350
2525
95,6
95,7
95,7
95,8
96,5
96,6
2500
2600
2900
3000
3200
3400
2175
2265
2525
2610
2785
2960
96,2
96,3
96,3
96,4
96,8
96,8
170
180
190
200
230
245
7000
7200
7900
8000
8100
8300
MJBM 710 SC61
MJBM 710 MA62
MJBM 710 LA62
MJBM 710 LB62
6
6
6
6
3200
3750
3900
4200
2785
3265
3395
3655
96,0
96,7
96,8
96,8
3600
4000
4200
4500
3135
3480
3655
3915
96,3
96,7
96,8
96,9
on request
on request
on request
on request
on request
on request
on request
on request
MJBM 800 __62
6
5800
5000
97,1
6200
5400
97,1
on request
on request
13,5
16,2
19,1
20,6
22,4
24,1
25,4
55,1
74,2
82,2
95,0
130
155
170
195
240
270
on request
on request
on request
on request
on request
1450
1600
1800
2000
2260
2530
2750
3200
3800
4700
5400
5700
6700
7100
8000
9200
9400
on request
on request
on request
on request
on request
63,8
81,6
89,7
106
230
310
on request
on request
on request
on request
on request
on request
3300
3900
4800
5600
8700
9700
on request
on request
on request
on request
on request
on request
8 poles
MJBM 400 SA8
MJBM 400 SB8
MJBM 400 SC8
MJBM 400 MA8
MJBM 400 MB8
MJBM 400 LA8
MJBM 400 LB8
MJBM 500 SA8
MJBM 500 SC8
MJBM 500 MB8
MJBM 500 LA8
MJBM 560 MA8
MJBM 560 LA8
MJBM 630 SC8
MJBM 630 MB8
MJBM 630 LA8
MJBM 630 LB8
MJBM 710 SC81
MJBM 710 MA81
MJBM 710 MD81
MJBM 710 LB82
MJBM 800 __82
380 V to 690 V @ 50 Hz - 750 rpm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10 poles
MJBM 500 SA10
MJBM 500 SC10
MJBM 500 MB10
MJBM 500 LA10
MJBM 630 MB10
MJBM 630 LB10
MJBM 710 SC101
MJBM 710 MA101
MJBM 710 MB101
MJBM 710 LB101
MJBM 710 LC102
MJBM 800 __102
210
270
315
375
450
520
650
830
1000
1100
1300
1500
1800
1750
2200
2450
2600
2400
2850
3200
3600
5400
185
235
275
330
395
455
570
725
870
960
1135
1305
1570
1525
1915
2135
2265
2090
2480
2785
3135
4700
91,6
92,1
92,4
92,6
93,1
93,3
93,6
94,6
95,1
95,2
95,3
95,6
95,9
95,4
95,9
96,1
96,2
96,4
96,5
96,6
96,7
96,9
380 V to 690 V @ 50 Hz - 600 rpm
6
6
6
6
6
6
6
6
6
6
6
6
520
650
760
840
1400
1800
2150
2400
2850
3400
3850
4800
455
570
665
735
1220
1570
1875
2090
2480
2960
3350
4100
94,0
94,3
94,8
95,1
95,6
95,8
95,9
95,9
96,4
96,4
96,5
96,6
380 V to 690 V @ 60 Hz - 900 rpm
250
330
370
450
520
620
760
950
1150
1300
1500
1900
2150
2000
2500
2800
3125
2750
3300
3800
4200
5700
220
290
325
395
455
540
665
830
1005
1135
1305
1655
1875
1740
2175
2440
2720
2395
2875
3310
3655
5000
91,9
92,4
92,7
92,9
93,4
93,6
93,9
95,0
95,4
95,5
95,8
95,6
95,9
96,2
96,5
96,6
96,7
96,7
96,8
96,9
97,1
97,1
IP23
380 V to 690 V @ 60 Hz -720 rpm
645
810
910
1050
1600
2200
2500
2800
3300
3900
4200
5200
565
705
795
915
1395
1915
2175
2440
2875
3395
3655
4500
94,5
94,7
95,2
95,5
95,9
96,2
96,3
96,3
96,7
96,7
96,8
96,9
IP23
1
2
15
Type
Leads
4 poles
380V to 690V / 50Hz
Power rating [kVA]
Water inlet temperature 36°C
Continuous duty - Air to water exchanger
95/50
70/50
ΔT cl. F
ΔT cl. B
380 V to 690 V @ 50 Hz - 1500 rpm
380V to 690V / 60Hz
Power rating [kVA]
95/50
70/50
ΔT cl. F
ΔT cl. B
380 V to 690 V @ 60Hz - 1800 rpm
MJRM 250 MA4
MJRM 250 MB4
MJRM 250 LA4
MJRM 250 LB4
12
12
12
12
130
145
170
200
115
130
150
175
150
170
200
220
135
150
175
200
MJRM 315 SA4
MJRM 315 SB4
MJRM 315 MA4
MJRM 315 MB4
12
12
12
12
230
270
320
350
210
230
280
300
280
320
380
410
245
280
330
360
MJRM 355 SA4
MJRM 355 SB4
MJRM 355 MA4
MJRM 355 MB4
12
12
12
6
400
450
540
630
350
400
470
550
460
530
620
730
400
460
540
640
MJRM 400 MB4
MJRM 400 LA4
MJRM 400 LB4
6
6
6
820
970
1020
715
850
890
1040
1120
1260
900
975
1100
MJRM 450 MB4
MJRM 450 LA4
MJRM 450 LB4
6
6
6
1210
1325
1510
1050
1150
1310
1700
1900
2025
1480
1660
1760
MJRM 500 SC4
MJRM 500 MA4
MJRM 500 MB4
MJRM 500 MC4
MJRM 500 LA4
MJRM 500 LB4
6
6
6
6
6
6
1700
1740
1900
2100
2200
2200
1480
1520
1660
1830
1920
1920
2110
2260
2450
2550
2800
2800
1840
1970
2135
2220
2440
2440
MJRM 560 MA4
MJRM 560 LA4
6
6
2350
2650
2050
2310
2850
3060
2480
2660
MJRM 630 SA41
MJRM 630 MA41
MJRM 630 LA41
6
6
6
2700
3000
3500
2350
2610
3050
3000
3300
3700
2610
2870
3220
MJRM 710 SC42
MJRM 710 MB42
6
6
3600
3800
3140
3310
4000
4300
3480
3750
6 poles
MJRM 400 SA6
MJRM 400 SB6
MJRM 400 SC6
MJRM 400 MA6
MJRM 400 MB6
MJRM 400 LA6
MJRM 400 LB6
MJRM 450 MB6
MJRM 450 LA6
MJRM 450 LB6
MJRM 500 SC6
MJRM 500 MA6
MJRM 500 MB6
MJRM 500 MC6
MJRM 500 LA6
MJRM 560 MA6
MJRM 560 LA6
MJRM 630 SB6
MJRM 630 SC6
MJRM 630 MA6
MJRM 630 MB6
MJRM 630 LA6
MJRM 630 LB6
MJRM 710 SC61
MJRM 710 MA62
MJRM 710 LA62
MJRM 710 LB62
MJRM 800 __62
380 V to 690 V @ 50 Hz - 1000 rpm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
320
350
390
490
550
630
760
800
940
1060
1200
1300
1400
1450
1680
1800
2000
2100
2200
2400
2500
2700
2900
3200
3750
3900
4200
5800
280
300
340
430
480
550
660
700
820
930
1050
1130
1220
1270
1470
1570
1740
1830
1920
2100
2180
2350
2530
2780
3260
3400
3650
5000
380 V to 690 V @ 60 Hz - 1200 rpm
370
420
460
580
650
740
900
950
1110
1260
1450
1600
1700
1800
2000
2050
2400
2500
2600
2900
3000
3200
3400
3600
4000
4200
4500
6200
325
370
405
505
570
640
780
830
970
1100
1260
1400
1480
1570
1740
1790
2090
2175
2260
2520
2610
2780
2960
3130
3480
3650
3920
5400
: 690 V recommended.
For MJRM generator series please consider additional derating factor:38 °C water inlet temperature: 0,99;
40 °C water inlet temperature: 0,98.
1
2
16
Type
Leads
8 poles
MJRM 400 SA8
MJRM 400 SB8
MJRM 400 SC8
MJRM 400 MA8
MJRM 400 MB8
MJRM 400 LA8
MJRM 400 LB8
MJRM 500 SA8
MJRM 500 SC8
MJRM 500 MB8
MJRM 500 LA8
MJRM 560 MA8
MJRM 560 LA8
MJRM 630 SC8
MJRM 630 MB8
MJRM 630 LA8
MJRM 630 LB8
MJRM 710 SC81
MJRM 710 MA81
MJRM 710 MD81
MJRM 710 LB82
MJRM 800 __82
380 V to 690 V @ 50 Hz - 750 rpm
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10 poles
MJRM 500 SA10
MJRM 500 SC10
MJRM 500 MB10
MJRM 500 LA10
MJRM 630 MB10
MJRM 630 LB10
MJRM 710 SC101
MJRM 710 MA101
MJRM 710 MB101
MJRM 710 LB101
MJRM 710 LC102
MJRM 800 __102
380V to 690V / 50Hz
Power rating [kVA]
95/50
70/50
ΔT cl. F
ΔT cl. B
190
245
285
340
400
470
590
830
1000
1100
1300
1500
1800
1750
2200
2450
2600
2400
2850
3200
3600
5400
380 V to 690 V @ 60 Hz - 900 rpm
170
215
250
300
350
410
515
725
870
960
1130
1300
1570
1530
1920
2140
2260
2100
2480
2780
3130
4700
380 V to 690 V @ 50 Hz - 600 rpm
6
6
6
6
6
6
6
6
6
6
6
6
470
590
680
760
1400
1800
2150
2400
2850
3400
3850
4800
380V to 690V / 50Hz
Power rating [kVA]
95/50
70/50
ΔT cl. F
ΔT cl. B
230
300
330
400
470
560
690
950
1150
1300
1500
1900
2150
2000
2500
2800
3125
2750
3300
3800
4200
5700
200
260
290
350
410
490
600
830
1000
1135
1300
1660
1875
1740
2175
2440
2720
2400
2870
3300
3650
5000
380 V to 690 V @ 60 Hz - 720 rpm
410
515
600
660
1220
1570
1875
2100
2480
2960
3350
4100
580
730
820
950
1600
2200
2500
2800
3300
3900
4200
5200
500
640
710
830
1400
1920
2180
2440
2880
3400
3660
4500
For MJRM generator series please consider additional derating factor:38 °C water inlet temperature: 0,99;
40 °C water inlet temperature: 0,98.
1
MJRM 900
17
DRAWINGS
B3 - DOUBLE BEARING
1
B2 - SINGLE BEARING
B20 - DOUBLE BEARING
1
1
1
(1) Dimensions for optional PMG
18
DIMENSIONS [mm]
Dimension
MJB 160 COMPACT
SB
SC
MA
MB
160
257
300
328
547
592
451
-
SA
H
HS
AB
AF
L
D max
L1
D1
Dimension
SA
H
HS
AB
AF
L
D max
L1
D1
Dimension
MJB 225
SB
MA
225
412
446
460
790
745
492
805
850
492
905
MB
SA
1366
1528
H
H1
HS
AB
AB1
AF
L
D max
L1
D1
MJB 500
MA
500
SC
1920
970
2170
970
Dimension
SA
MJB 710
MA
710
SC
672
685
780
432
LB
MJB 315
SB
MA
315
555
600
632
SA
998
945
MB
1105
711
1050
1052
1212
624
MJB 400
MA
MB
400
Dimensions available on request
675
800
800
1200
1400
883
1370
1570
780
SB
LA
LB
MB
MJB 450
LA
450
MB
LA
800
MJB 800
MB
LA
800
MA
LB
740
900
1600
1517
1777
1770
1807
1987
LA
900
1970
710
354
MJB 250
MB
LA
250
468
505
502
MB
552
MJB 560
MJB 630
MA
LA
SA
SB
MA
MB
560
630
870
948
1100
1280
900
2020
2035
2135
1070
2270
2305
2405
2160
2360
1070
1200
MB
867
1000
1720
MJB 200
SB
MA
200
323
405
410
SA
615
532
690
SA
MB
632
627
918
711
Dimension
MA
552
700
1298
MJB 160
SC
160
257
300
328
451
858
620
670
1136
SB
587
MA
845
MJB 355
SB
MA
355
SA
H
H1
HS
AB
AB1
AF
L
D max
L1
D1
LA
SA
H
H1
HS
1170
1500
AB
1500
2100
AB1
AF
L
Dimension available on request
D max
L1
2450
2650
2900
3100
3300
D1
1413
D (max) dimension shown refers to biggest adaptor/coupling
LA
2460
LB
COUPLING
Adaptor
5
160
4
200
3
4
3
2
1
4
225
3
2
3
250
2
1
3
Sizes [mm]
315
2
1 1/2
0
1
355
1/2
0
1
400
1/2 0
00
0
450
00
0
500
00
560
00
6 1/2
7 1/2
8
10
11 1/2
14
16
18
21
Available
Most common
19
HEADQUARTERS
ITALIAN BRANCHES
Marelli Motori S.p.A.
Milan
Via Sabbionara, 1
36071 Arzignano (VI) - Italy
(T) +39 0444 479.711
(F) +39 0444 479.888
www.marellimotori.com
[email protected]
Via Cesare Cantù, 29
20092 Cinisello Balsamo (MI) - Italy
(T) +39 02 660.131.66
(F) +39 02 660.134.83
[email protected]
Florence
Via Panciatichi, 37/2
50127 Firenze - Italy
(T) +39 055 431.838
(F) +39 055 433.351
[email protected]
MARELLI MOTORI OVERSEAS COMPANIES
GREAT BRITAIN
CENTRAL EUROPE
USA
Marelli UK, Ltd
Marelli Central Europe Gmbh
Marelli USA, Inc
Meadow Lane
Loughborough
Leicester LE111NB
UK
(T) +44 1509 615 518
(F) +44 1509 615 514
[email protected]
Heilswannenweg 50
31008 Elze
Germany
(T) +49 5068 462 400
(F) +49 5068 462 409
[email protected]
1620 Danville Road
PO Box 410
Harrodsburg, KY 40330
USA
(T) +1 859 734 2588
(F) +1 859 7340629
[email protected]
ASIA PACIFIC
SOUTH AFRICA
SPAIN
Marelli Asia Pacific Sdn Bhd
Marelli Electrical Machines South Africa (Pty) Ltd
Representative Office
Lot PT 5038-5041 Jalan Teluk Datuk 28/40
Off Persiaran Sepang, Seksyen 28,
40400 Shah Alam, Selangor D.E.
Malaysia
(T) +60 3 5192 7213
(F) +60 3 5192 6293
[email protected]
Unit 4, 55 Activia Rd - Activia Park
Elandsfontein,
1406 Gauteng
Republic of South Africa
(T) +27 11 822 5566
(F) +27 11 828 8089
[email protected]
Barcelona
Spain
(T) +34 6644641219
[email protected]
SIN.CT.024.13 GB
MARELLI MOTORI reserves the right to change the design, technical specification and dimensions in order to update or improve its products, without prior notice

Three Phase Synchronous Generators

Transcription

Similar documents

My Home Is My Office

HYUNDAI WIA CNC Turning Center

Logistik WebServices zur Unterstützung des Distributed Order

Three Phase Squirrel Cage Non-sparking Motors Dust

Untitled - Lumicenter

MarelliMotori - Tecnica Industriale S.r.l.

Hyundai International_Company introduction_eng