And Rear Seats Courtesy of AMERICAN HONDA

Transcription

2008 Honda Ridgeline RT
2006-08 ACCESSORIES & EQUIPMENT Seats - Ridgeline
2006-08 ACCESSORIES & EQUIPMENT
Seats - Ridgeline
COMPONENT LOCATION INDEX
Fig. 1: Identifying Front Seats (Driver's/Passenger's Side) And Rear Seats
Courtesy of AMERICAN HONDA MOTOR CO., INC.
FRONT SEAT REMOVAL/INSTALLATION
Special Tools Required
KTC trim tool set SOJATP2014 *
* Available through the American Honda Tool and Equipment Program; call 888me
Monday, April 13, 2009 6:02:24
6:02:18 AM
Page 1
© 2005 Mitchell Repair Information Company, LLC.
424-6857
SRS components are located in this area. Review the SRS component locations (see
COMPONENT LOCATION INDEX ) and the precautions and procedures (see
PRECAUTIONS AND PROCEDURES ) before performing repairs or service.
NOTE:
Use the appropriate tool from the KTC trim tool set to
avoid damage when prying components.
Take care not to scratch the body or tear the seat
covers.
Put on gloves to protect your hands.
DTC codes will set if the ignition is turned ON (II) with
the seats removed.
1. Make sure you have the anti-theft codes for the radio and the navigation
system, then write down the audio presets.
2. Tilt the steering wheel all the way up.
3. Detach the side clips and middle hooks (A), then remove the rear riser cover
(B).
me
Monday, April 13, 2009 6:02:18 AM
Page 2
Fig. 2: Removing Rear Riser Cover
4. Slide the seat fully to the rear to access the front riser cover.
5. Detach the clip and release the hook (A), and remove the front riser cover (B)
from both sides.
me
Monday, April 13, 2009 6:02:18 AM
Page 3
Fig. 3: Removing Front Riser Cover
6. Disconnect the negative cable from the battery, and wait at least 3 minutes
before beginning work.
7. Remove the bolts securing the front seat (A), and remove the headrest (B).
me
Monday, April 13, 2009 6:02:18 AM
Page 4
Fig. 4: Removing Headrest
8. Tilt the front seat forward and disconnect the side airbag connector (A) and
seat wire harness connector (B).
Manual height adjustable seat (driver's):
Disconnect the seat belt switch connector (C).
me
Monday, April 13, 2009 6:02:18 AM
Page 5
With navigation system: Disconnect the navigation unit connectors (D) and
GPS antenna harness connector (E).
NOTE:
The 10-way power seat (driver's) is shown; the manual
seat (passenger's) and manual height adjustable seat
(driver's) are similar.
me
Monday, April 13, 2009 6:02:18 AM
Page 6
me
Monday, April 13, 2009 6:02:18 AM
Page 7
Fig. 5: Disconnecting Side Airbag Connector And Seat Wire Harness
Connector
9. Install the seat in the reverse order of removal, and note these items:
Apply medium strength type liquid thread lock to the front seat mounting
bolts before reinstallation.
Make sure each connector is plugged in properly.
Reconnect the negative cable to the battery.
Tighten the seat mounting bolts to the specified torque in the sequence
shown. Slide the seat all the way back and tighten (1) and (2), then slide it
forward and tighten (3) and (4).
Enter the anti-theft codes for the radio and navigation system (if
equipped).
Reset the clock (on vehicles without navigation).
Perform the power window control unit reset procedure (see
RESETTING THE POWER WINDOW CONTROL UNIT ).
Seat mounting bolts tightening sequence
me
Monday, April 13, 2009 6:02:18 AM
Page 8
Fig. 6: Identifying Tightening Sequence Of Seat Mounting Bolts With
Torque Specifications
FRONT SEAT DISASSEMBLY/REASSEMBLY
me
Monday, April 13, 2009 6:02:18 AM
Page 9
* Available through the American Honda Tool and Equipment Program; call 888424-6857
SEAT-BACK/SEAT CUSHION
NOTE:
Take care not to tear the seams or damage the seat
covers.
DTC codes will set it the ignition is turned ON (II) with
the seats removed.
1. Remove the front seat (see FRONT SEAT REMOVAL/INSTALLATION ).
2. 10-way power seat: Remove the clip and release the hooks (A), then remove
the inner cover (B).
me
Monday, April 13, 2009 6:02:18 AM
Page 10
Fig. 7: Removing Inner Cover
3. Remove the center cover (A).
1 Remove the clip (B), and detach the clip (C).
2 Pull up the cover, then release the hooks (D, E).
me
Monday, April 13, 2009 6:02:18 AM
Page 11
Fig. 8: Removing Center Cover
me
Monday, April 13, 2009 6:02:18 AM
Page 12
4. Driver's 10-way power seat: Remove the center cover (A).
1 Remove the screw.
2 Pull up the cover, then release the hooks (B, C, D).
Fig. 9: Releasing Hooks
5. Driver's 10-way power seat: Remove the screw and release the hooks (A), then
remove the front cover (B).
me
Monday, April 13, 2009 6:02:18 AM
Page 13
Fig. 10: Removing Front Cover
6. Remove the recline cover (A).
1 Gently pull out along the bottom to release the hooks (B), then remove
the cap (C).
2 Remove the bolts (D), then remove the height handle (E) and screw (F).
3 Remove the recline knob (G) and clips (H), and detach the clip (I).
4 Pull up the cover, then release the hooks (J, K).
me
Monday, April 13, 2009 6:02:18 AM
Page 14
Fig. 11: Removing Recline Cover With Torque Specifications
me
Monday, April 13, 2009 6:02:18 AM
Page 15
7. 10-way power seat: Remove the recline cover (A).
1 Remove the screws.
2 Pull up the cover, then release the hooks (B, C).
3 Disconnect the recline switch and up-down switch connector (D),
lumbar support switch connector (E).
4 Detach the harness clips (F) from the recline cover.
me
Monday, April 13, 2009 6:02:19 AM
Page 16
Fig. 12: Disconnecting Recline Switch, Up-Down Switch Connector
And Lumbar Support Switch Connector
me
Monday, April 13, 2009 6:02:19 AM
Page 17
8. From under the seat cushion, disconnect the seat-back heater connector (A)
lumbar support switch connector (B) and recline motor subharness connector
(C), then detach the connector clip. Detach the side airbag connector clip (D),
OPDS unit connector clip (E) on the passenger's seat. Release the hook springs
(F) and seat cushion cover (G), pull the cover back, and remove the wire ties
(H).
me
Monday, April 13, 2009 6:02:19 AM
Page 18
Fig. 13: Removing Hook Springs, Seat Cushion Cover And Wire Ties
me
Monday, April 13, 2009 6:02:19 AM
Page 19
Fig. 14: Removing Hook Springs, Seat Cushion Cover And Wire Ties (10Way Power Seat)
9. Remove the seat-back (A).
1 Remove the bolts.
me
Monday, April 13, 2009 6:02:19 AM
Page 20
2 Lift the seat-back, then pull the harnesses (B), out through the hole in the
seat cushion trim cover.
Fig. 15: Removing Seat-Back And Harnesses Through Hole In Seat
Cushion Trim Cover With Torque Specifications
10. Assemble the seat-back and seat cushion in the reverse order of disassembly,
and note these items:
Replace any damaged clips.
Push the clips into place securely.
Apply multipurpose grease to the moving parts of the seat track.
me
Monday, April 13, 2009 6:02:19 AM
Page 21
To prevent wrinkles in the seat cushion cover, stretch the material evenly
over the pad.
The passenger's seat is shown; the driver's seat is similar.
SEAT-BACK
NOTE:
Replace the push nuts with new ones. Make sure the
push nuts are installed correctly.
Apply low strength type liquid thread lock to the motor
mounting bolt before reinstallation.
me
Monday, April 13, 2009 6:02:19 AM
Page 22
Fig. 16: Identifying Back Seat Components With Torque
Specifications
FRONT SEAT LINKAGE DISASSEMBLY/REASSEMBLY
FRONT SEAT LINKAGE DISASSEMBLY/REASSEMBLY - PASSENGER'S MANUAL
'06 model
NOTE:
Apply oil to the pivot portions of the slide lock.
Apply multipurpose grease to the sliding parts and
pivot portions of the seat tracks.
me
Monday, April 13, 2009 6:02:19 AM
Page 23
Fig. 17: Disassembling Front Seat Linkage (Manual
Seat) With Torque Specifications ('06 Models)
'07-08 models
The front ODS unit must be calibrated after any of these actions (see ODS
UNIT CALIBRATION ):
Front passenger's seat replacement (including any seat components)
Replacement of the seat weight sensors
Replacement of the ODS unit
NOTE:
me
Monday, April 13, 2009 6:02:19 AM
Page 24
Apply oil to the pivot portions of the slide locks.
Apply multipurpose grease to the sliding portions of the
seat tracks.
When tightening the weight sensor mounting bolts,
tighten the bolts in the sequence shown. Improper
tightening could cause the front passenger's airbag
system to malfunction.
Make sure the weight sensor wires are routed properly
so they are not pinched and do not interfere with other
parts.
Fig. 18: Disassembling Front Seat Linkage (Manual Seat) With Torque
Specifications ('07-08 Models)
me
Monday, April 13, 2009 6:02:19 AM
Page 25
FRONT SEAT LINKAGE DISASSEMBLY/REASSEMBLY - DRIVER'S MANUAL HEIGHT
ADJUSTABLE
'06 model
NOTE:
Fig. 19: Disassembling Front Seat Linkage (Manual
me
Monday, April 13, 2009 6:02:19 AM
Page 26
Height Adjustable Seat) With Torque Specifications ('06
Model)
'07-08 models
The operation of the driver's seat position sensor must be checked after any of
these actions (see ODS UNIT OPERATION CHECK ):
Driver's seat position sensor replacement
Cover plate (front side of driver's seat slide rail) replacement
NOTE:
me
Monday, April 13, 2009 6:02:19 AM
Page 27
Fig. 20: Disassembling Front Seat Linkage (Manual Height Adjustable Seat)
With Torque Specifications ('07-08 Model)
FRONT SEAT LINKAGE DISASSEMBLY/REASSEMBLY - DRIVER'S 10-WAY POWER
'06 model
NOTE:
To remove the slide motor and slide gearbox, slide the
front seat forward fully.
Before installing the slide motor and slide gearbox,
align portion (A) as shown to align both slide gearbox
positions.
me
Monday, April 13, 2009 6:02:19 AM
Page 28
Apply multipurpose grease to the sliding and pivot
portions.
Check operation of the recline adjuster and slide/updown adjuster.
Fig. 21: Disassembling Front Seat Linkage (10-Way
Power Seat) With Torque Specifications ('06 Model)
'07-08 models
me
Monday, April 13, 2009 6:02:19 AM
Page 29
The operation of the driver's seat position sensor must be checked after any of
these actions (see ODS UNIT OPERATION CHECK ):
Driver's seat position sensor replacement
Cover plate (front side of driver's seat slide rail) replacement
NOTE:
To remove the slide motor and slide gearbox, slide the
front seat forward fully.
Before installing the slide motor and slide gearbox,
align portion (A) as shown to align both slide gearbox
positions.
Apply multipurpose grease to the sliding and pivot
portions.
Check operation of the recline adjuster and slide/updown adjuster.
me
Monday, April 13, 2009 6:02:19 AM
Page 30
Fig. 22: Disassembling Front Seat Linkage (10-Way Power Seat) With Torque
Specifications ('07-08 Models)
FOR SOME MODELS (DRIVER'S SEAT)
NOTE:
When prying with a flat-tip screwdriver, wrap it with
protective tape to prevent damage.
Take care not to bend the cable.
me
Monday, April 13, 2009 6:02:19 AM
Page 31
covers.
1. Remove these items:
Lumbar support knob (see step 4 )
Back panel (see step 5 )
2. Release the hook strips on the inside of the seat-back (see step 6 ).
3. Remove the screws securing the lumbar support actuator (A).
me
Monday, April 13, 2009 6:02:19 AM
Page 32
Fig. 23: Removing Lumbar Support Actuator
me
Monday, April 13, 2009 6:02:19 AM
Page 33
4. Remove the metal clamps (A) and release the wire (B) of the lumber support
(C) from the retainers (D), then remove the lumbar support and lumbar support
actuator (E) as an assembly.
Fig. 24: Removing Metal Clamps And Wire Of Lumber Support From
me
Monday, April 13, 2009 6:02:19 AM
Page 34
Retainers
5. Install the lumbar support in the reverse order of removal, and note these items:
To prevent wrinkles when installing a seat-back cover, make sure the
material is stretched evenly over the pad before securing the hook strips.
Replace the back panel clips with new ones.
Replace the metal clips with new ones.
FRONT SEAT-BACK COVER REPLACEMENT
NOTE:
Seats with a side airbag have a "SIDE AIRBAG" label on
the seat-back. Because the component parts (seat-back
cover, cushion, etc.) of seats with and without airbags
are different, make sure you install only the correct
replacement parts.
Do not repair any tears or frayed spots of the seat-back
cover. If necessary, replace the seat-back cover.
covers.
On the passenger's seat, do not touch the OPDS sensor
in the seat-back pad, and keep it away from oil. Oil can
corrode the sensor causing it to fail.
me
Monday, April 13, 2009 6:02:19 AM
Page 35
2. Remove the seat-back (see FRONT SEAT
DISASSEMBLY/REASSEMBLY ).
3. Remove the head restraint.
4. If equipped, remove the clip (A), then remove the lumbar support handle (B).
me
Monday, April 13, 2009 6:02:19 AM
Page 36
Fig. 25: Removing Lumbar Support Handle
me
Monday, April 13, 2009 6:02:19 AM
Page 37
5. Detach the clips and hooks (A) by pulling the bottom of the back panel (B)
back, then gently pull down the panel to release the hooks (C) from the seatback frame, and remove the panel.
Fig. 26: Removing Panel
me
Monday, April 13, 2009 6:02:19 AM
Page 38
6. Release the hook strips (A), then loosen the seat-back cover (B).
Fig. 27: Loosening Seat-Back Cover
7. Pull the recline motor subharness (A) (some driver's seats), seat-back heater
harness (B) (some driver's seats), side airbag harness (C), lumbar support
motor harness (D) (some driver's seats), and the OPDS harness (E) (passenger's
me
Monday, April 13, 2009 6:02:19 AM
Page 39
seat) out through the harness guides (F).
Fig. 28: Removing Recline Motor Subharness, Seat-Back Heater Harness,
me
Monday, April 13, 2009 6:02:19 AM
Page 40
Side Airbag Harness, Lumbar Support Motor Harness And OPDS
Harness
8. Release the front hook (A) and rear hook (B) of the reinforcing cloth (C) from
seat-back frame (D).
Fig. 29: Releasing Front Hook And Rear Hook Of Reinforcing Cloth From
Seat-Back Frame
9. Pinch the tabs on the ends of the headrest guides. (A), and remove them from
the seat-back.
me
Monday, April 13, 2009 6:02:19 AM
Page 41
Fig. 30: Removing Tabs From Seat-Back
me
Monday, April 13, 2009 6:02:19 AM
Page 42
10. From the back of the seat-back, pass both lower retainers (A) through the slots
in the seat-back pad, and release the clips (B) and inside springs (C).
me
Monday, April 13, 2009 6:02:19 AM
Page 43
me
Monday, April 13, 2009 6:02:19 AM
Page 44
Fig. 31: Releasing Clips And Inside Springs
11. Pull back the edge of the seat-back cover all the way around, and release the
clips (A), then remove the seat-back cover.
me
Monday, April 13, 2009 6:02:19 AM
Page 45
Fig. 32: Removing Clips And Seat-Back Cover
12. Install the cover in the reverse order of removal, and note these items:
Reinitializes the OPDS control unit (see OPDS/ODS UNIT
INITIALIZATION ).
material is stretched evenly over the pad before securing the clips, hooks,
and hook strips.
Using commercially available upholstery ring pliers (A), replace all of the
clips you removed with new ones (B).
Reinstall the front hook (C) and rear hook (D) of the reinforcing cloth (E)
securely.
Use only original Honda replacement seat-back covers.
If equipped, make sure the recline motor harness, side airbag harness, seatback heater harness, and OPDS unit harness (passenger's seat) are routed
properly.
me
Monday, April 13, 2009 6:02:19 AM
Page 46
Fig. 33: Installing Front Hook And Rear Hook Of Reinforcing Cloth
me
Monday, April 13, 2009 6:02:19 AM
Page 47
FRONT SEAT CUSHION COVER REPLACEMENT
NOTE:
Take care not to tear the seams of damage the seat
covers.
2. Remove the seat-back (see FRONT SEAT
3. From under the seat cushion, disconnect the seat cushion heater connector, and
detach the seat cushion heater connector clip on the manual seat.
4. Release the hook strips (A) from both sides of the seat cushion.
me
Monday, April 13, 2009 6:02:19 AM
Page 48
Fig. 34: Releasing Hook Strips From Both Sides Of Seat Cushion (Manual
Seat/Manual Height Adjustable Seat)
me
Monday, April 13, 2009 6:02:19 AM
Page 49
Fig. 35: Releasing Hook Strips From Both Sides Of Seat Cushion (10-Way
Power Seat)
5. Release the hooks (A) from under the seat cushion (B).
me
Monday, April 13, 2009 6:02:19 AM
Page 50
Fig. 36: Removing Hooks From Under Seat Cushion
me
Monday, April 13, 2009 6:02:19 AM
Page 51
6. Remove the silencer (A) and seat cushion pad (B) from the seat cushion frame
(C).
Fig. 37: Removing Silencer And Seat Cushion Pad From Seat Cushion
Frame
7. Release the clips (A) from under the seat cushion (B).
me
Monday, April 13, 2009 6:02:19 AM
Page 52
Fig. 38: Removing Clips From Under Seat Cushion
8. Pull back the edge of the seat cushion cover all the way around, and release the
clips (A), then remove the seat cushion cover.
me
Monday, April 13, 2009 6:02:19 AM
Page 53
Fig. 39: Removing Clips And Seat Cushion Cover (Leather Seat/Fabric
Seat)
me
Monday, April 13, 2009 6:02:19 AM
Page 54
To prevent wrinkles when installing a seat cushion cover, make sure the
material is stretched evenly over the pad before securing the clips and
hook strips.
Using commercially available upholstery ring pliers (A), replace all of the
clips you removed with new ones (B).
Fig. 40: Installing Clips
REAR SEAT REMOVAL/INSTALLATION
me
Monday, April 13, 2009 6:02:19 AM
Page 55
NOTE:
Have an assistant help you when removing and
installing the rear seat.
Take care not to scratch the trim and panels or tear the
seat covers.
REAR SEAT ASSEMBLY REMOVAL/INSTALLATION
1. Remove the left rear under-seat trim panel (A).
1 Detach the clips (B, C) and hooks (D).
2 Release the rear center seat belt (E) and left seat belt buckle (F) through
the slits (G) in the trim panel.
me
Monday, April 13, 2009 6:02:19 AM
Page 56
Fig. 41: Removing Left Rear Under-Seat Trim Panel
2. Detach the clips (A, B), then remove the right rear under-seat trim panel (C).
me
Monday, April 13, 2009 6:02:19 AM
Page 57
Fig. 42: Removing Right Rear Under-Seat Trim Panel
3. Remove the lower middle rear seat mount cover (A).
1 Detach the hooks (B).
2 Release the right rear seat belt buckle (C) and center seat belt buckle (D)
me
Monday, April 13, 2009 6:02:19 AM
Page 58
through the slits (E) in the cover.
Fig. 43: Removing Lower Middle Rear Seat Mount Cover
4. From both sides, pull out the rear seat mount covers (A) to detach the clips,
then remove the covers.
me
Monday, April 13, 2009 6:02:19 AM
Page 59
Fig. 44: Removing Rear Seat Mount Covers
5. Remove the headrests (A). From both sides of the rear trim panel (B), detach
the hooks (C) and tabs (D), then remove the caps (E).
me
Monday, April 13, 2009 6:02:19 AM
Page 60
Fig. 45: Removing Headrests
me
Monday, April 13, 2009 6:02:19 AM
Page 61
6. Remove the right rear seat belt buckle and center seat belt buckle (see LEFT
REAR SEAT BELT BUCKLE ).
7. Remove the center seat belt lower anchor bolt (see step 2 on REAR CENTER
SEAT BELT ) and left rear seat belt buckle (see LEFT REAR SEAT BELT
BUCKLE ).
8. Pull out the center seat belt through the gap between the rear seat-back and rear
seat cushion (see step 3 on REAR CENTER SEAT BELT ).
9. Remove the rear seat assembly (A).
1 Remove the bolts.
2 Lift the seat assembly up to release the hooks (B) from the holes (C) on
the body, then remove the seat assembly.
me
Monday, April 13, 2009 6:02:19 AM
Page 62
Fig. 46: Removing Rear Seat Assembly
10. Install the seat in the reverse order of removal, and note these items:
me
Monday, April 13, 2009 6:02:19 AM
Page 63
Before installing the anchor bolt, make sure there are no twists or kinks in
the center seat belt.
Tighten the seat mounting bolts to the specified torque in the sequence
shown.
Replace any damaged cover clips.
me
Monday, April 13, 2009 6:02:19 AM
Page 64
Fig. 47: Identifying Tightening Sequence Of Seat Mounting Bolts
With Torque Specifications
REAR SEAT-BACK REMOVAL/INSTALLATION
me
Monday, April 13, 2009 6:02:19 AM
Page 65
Left rear under-seat trim panel
Right rear under-seat trim panel
Lower middle rear seat mount cover
Rear seat mount covers, both sides
2. Remove the upper middle rear seat mount cover (A).
1 Fold the right rear seat belt buckle (B) and center seat belt buckle (C)
down, and hold them.
2 Detach the clips, and release the hooks (D).
me
Monday, April 13, 2009 6:02:19 AM
Page 66
me
Monday, April 13, 2009 6:02:19 AM
Page 67
Fig. 48: Removing Upper Middle Rear Seat Mount Cover
3. Remove the caps from both sides of the rear trim panel.
4. Remove the center seat belt lower anchor bolt (see step 2 on REAR CENTER
SEAT BELT ).
5. Pull out the center seat belt through the gap between the rear seat-back and rear
seat cushion (see step 3 on REAR CENTER SEAT BELT ).
6. Remove the bolts securing the rear seat-back (A).
me
Monday, April 13, 2009 6:02:19 AM
Page 68
Fig. 49: Removing Bolts Securing Rear Seat-Back With Torque
Specifications
7. Lift the seat-back (A) up to release the hooks (B) from the holes (C) on the
body, then remove the seat-back.
me
Monday, April 13, 2009 6:02:19 AM
Page 69
Fig. 50: Removing Hooks From Holes On Body And Seat-Back
8. Install the seat-back in the reverse order of removal, and note these items:
Before installing the anchor bolt, make sure there are no twists or kinks in
the center seat belt.
Replace any damaged cover clips.
me
Monday, April 13, 2009 6:02:19 AM
Page 70
REAR SEAT LEG GUIDE REPLACEMENT
1. Pull the seat leg guide cover (A) up to detach the clips (B, C), then remove it.
me
Monday, April 13, 2009 6:02:19 AM
Page 71
Fig. 51: Removing Seat Leg Guide Cover
2. Remove the bolts, then remove the seat leg guide (A).
Fig. 52: Removing Seat Leg Guide With Torque Specifications
me
Monday, April 13, 2009 6:02:19 AM
Page 72
3. Install the leg guide in the reverse order of removal, and note these items:
Replace any damaged clips.
Before reinstalling the leg guide cover, adjust the seat leg guide (A)
position.
Push the clips into place securely.
Fig. 53: Installing Seat Leg Guide With Torque Specifications
REAR SEAT ARMREST REPLACEMENT
NOTE:
me
Monday, April 13, 2009 6:02:19 AM
Page 73
covers.
1. Remove the rear seat-back (see REAR SEAT-BACK
REMOVAL/INSTALLATION ).
2. Remove the center headrest (A). Pinch the tabs on the ends of the headrest
guides (B), and remove them from the seat-back.
me
Monday, April 13, 2009 6:02:19 AM
Page 74
Fig. 54: Removing Center Headrest
me
Monday, April 13, 2009 6:02:19 AM
Page 75
3. Pull out the top of the armrest board (A), and then pull it up to release the
hooks (B) from the frame wire (C) and to release the board from the armrest
pivot brackets (D).
Fig. 55: Removing Board From Armrest Pivot Brackets
me
Monday, April 13, 2009 6:02:19 AM
Page 76
4. Remove the nuts, then remove the armrest (A).
Fig. 56: Removing Armrest With Torque Specifications
me
Monday, April 13, 2009 6:02:19 AM
Page 77
5. Install the armrest in the reverse order of removal, and make sure the armrest
board hooks are installed securely.
REAR SEAT ARMREST BEVERAGE HOLDER REPLACEMENT
NOTE:
covers.
1. Using a trim tool, detach the hooks (A), then remove the armrest beverage
holder (B).
me
Monday, April 13, 2009 6:02:19 AM
Page 78
Fig. 57: Removing Armrest Beverage Holder
2. Install the beverage holder by pushing on the hook portions until the hooks
snap into place securely.
REAR SEAT CUSHION DISASSEMBLY/REASSEMBLY
me
Monday, April 13, 2009 6:02:19 AM
Page 79
NOTE:
covers.
1. Remove the bolts, then separate the rear seat-back (A) and rear seat cushion
(B).
me
Monday, April 13, 2009 6:02:19 AM
Page 80
Fig. 58: Removing Rear Seat-Back And Rear Seat Cushion With Torque
me
Monday, April 13, 2009 6:02:19 AM
Page 81
Specifications
2. Remove the bolts (A, B), then separate the left seat-back (C) and right seatback (D).
Fig. 59: Removing Left Seat-Back And Right Seat-Back With Torque
me
Monday, April 13, 2009 6:02:19 AM
Page 82
Specifications
3. Remove the screw. Release the tabs (A) and hooks (B), then remove the recline
outer cover (C).
NOTE:
The left seat cushion is shown; the right seat cushion is
similar.
me
Monday, April 13, 2009 6:02:19 AM
Page 83
Fig. 60: Removing Recline Outer Cover
4. Remove the screw, then remove the recline inner cover (A).
me
Monday, April 13, 2009 6:02:19 AM
Page 84
Fig. 61: Removing Recline Inner Cover
5. Pull back the rear seat cushion under-cover trim (A) to release the hooks (B),
and release the hooks (C), then remove it.
Left seat cushion B
me
Monday, April 13, 2009 6:02:19 AM
Page 85
Fig. 62: Removing Rear Seat Cushion Under-Cover Trim (Left Seat
Cushion)
Right seat cushion B
me
Monday, April 13, 2009 6:02:19 AM
Page 86
Fig. 63: Removing Rear Seat Cushion Under-Cover Trim (Right Seat
Cushion)
6. Remove the rear seat cushion under-cover (A).
1 Using a trim tool, remove the caps (B).
2 Remove the screws (C, D).
3 Release the hook strips (E) of the seat cushion cover from the undercover.
me
Monday, April 13, 2009 6:02:19 AM
Page 87
Left seat cushion
me
Monday, April 13, 2009 6:02:19 AM
Page 88
me
Monday, April 13, 2009 6:02:19 AM
Page 89
Fig. 64: Removing Rear Seat Cushion Under-Cover (Left Seat Cushion)
Right seat cushion
me
Monday, April 13, 2009 6:02:19 AM
Page 90
Fig. 65: Removing Rear Seat Cushion Under-Cover (Right Seat Cushion)
me
Monday, April 13, 2009 6:02:19 AM
Page 91
7. Remove the rear seat cushion handle (see REAR SEAT CUSHION
HANDLE REPLACEMENT ).
8. Release the hooks (A) securing the seat cushion cover.
Fig. 66: Removing Hooks Securing Seat Cushion Cover
me
Monday, April 13, 2009 6:02:19 AM
Page 92
9. Separate the seat cushion frame (A) and seat cushion cover/pad (B).
Fig. 67: Removing Seat Cushion Frame And Seat Cushion Cover/Pad
10. Assemble the seat cushion in the reverse order of disassembly, and note these
items:
To prevent wrinkles in the seat cushion cover, stretch the material evenly
over the pad.
Push each cover hooks and tabs into place securely.
me
Monday, April 13, 2009 6:02:19 AM
Page 93
REAR SEAT CUSHION HANDLE REPLACEMENT
NOTE:
covers.
similar.
1. Remove the rear seat assembly (see REAR SEAT
2. Remove the seat cushion (see REAR SEAT CUSHION
Recline outer cover (see step 3 )
Rear seat cushion under-cover trim (see step 5 )
Rear seat cushion under-cover (see step 6 )
4. Using a trim tool, release the hooks (A), and pull out the handle cover (B) to
release the hooks (C), then remove the cover from the rear seat cushion handle
(D).
me
Monday, April 13, 2009 6:02:19 AM
Page 94
Fig. 68: Removing Cover From Rear Seat Cushion Handle
5. Release the fastener (A), then pull back the seat cushion cover (B). Disconnect
the handle cable (C).
me
Monday, April 13, 2009 6:02:19 AM
Page 95
Fig. 69: Removing Seat Cushion Cover
6. Remove the screws, and release the hooks (A), then remove the handle (B)
from the cushion frame (C) by pulling out the cable (D) through the hole in the
cushion frame.
me
Monday, April 13, 2009 6:02:19 AM
Page 96
Fig. 70: Removing Handle From Cushion Frame
7. Disconnect the handle cable (A) from the handle (B).
me
Monday, April 13, 2009 6:02:19 AM
Page 97
Fig. 71: Disconnecting Handle Cable From Handle
8. Install the handle in the reverse order of removal, and note these items:
Make sure the handle cable is connected securely.
me
Monday, April 13, 2009 6:02:19 AM
Page 98
Check the seat cushion tip-up operation.
REAR SEAT CUSHION PIVOT CABLE REPLACEMENT
NOTE:
covers.
similar.
2. Remove the seat cushion (see REAR SEAT CUSHION
Recline outer cover (see step 3 )
Rear seat cushion under-cover trim (see step 5 )
Rear seat cushion under-cover (see step 6 )
4. Release the hooks (A), and pull back the seat cushion cover (B).
me
Monday, April 13, 2009 6:02:19 AM
Page 99
5. Release the tabs (A) and clip, then remove the pivot outer cover (B) and pivot
inner cover (C).
me
Monday, April 13, 2009 6:02:19 AM
Page 100
Fig. 73: Removing Pivot Outer Cover And Pivot Inner Cover
6. Remove the rear seat cushion pivot cable (A).
me
Monday, April 13, 2009 6:02:19 AM
Page 101
1 Remove the lock washer (B), then disconnect the cable, and detach the
cable clip (C).
2 Remove the screws (D), then remove the cable joint (E).
3 Remove the nut (F), then remove the cable guide (G) and inner
mounting bracket (H), and disconnect the cable from the cable guide.
me
Monday, April 13, 2009 6:02:19 AM
Page 102
Fig. 74: Removing Rear Seat Cushion Pivot Cable With Torque
Specifications
me
Monday, April 13, 2009 6:02:19 AM
Page 103
7. Install the pivot cable in the reverse order of removal, and note these items:
Make sure the pivot cable is connected securely.
Replace the lock washer with new one.
REAR SEAT-BACK COVER REPLACEMENT
NOTE:
covers.
1. Remove the seat-back (see REAR SEAT-BACK
2. Remove the armrest (see REAR SEAT ARMREST REPLACEMENT ).
3. Release the hook strips (A) and fasteners (B).
Fig. 75: Removing Hook Strips And Fasteners
me
Monday, April 13, 2009 6:02:19 AM
Page 104
4. Pull back the edge of the seat-back cover (A), then release the hook strips (B,
C).
Fig. 76: Pulling Back Edge Of Seat-Back Cover And Releasing Hook
Strips
5. Pull out the headrest guides (A) while pinching the tabs on the end of the
guides, and remove them.
me
Monday, April 13, 2009 6:02:19 AM
Page 105
Fig. 77: Removing Headrest Guides
me
Monday, April 13, 2009 6:02:19 AM
Page 106
6. Pull back the edge of the seat-back cover (A) all the way around, and release
the clips (B), then remove the seat-back cover.
Fig. 78: Removing Seat-Back Cover
material is stretched evenly over the pad before securing the hook strips
and clips.
Replace any clips you removed with new ones. Install them with
commercially available upholstery ring pliers.
REAR SEAT CUSHION COVER REPLACEMENT
me
Monday, April 13, 2009 6:02:19 AM
Page 107
NOTE:
covers.
2. Remove the seat cushion cover/pad from the seat cushion frame (see REAR
SEAT CUSHION DISASSEMBLY/REASSEMBLY ).
3. Pull back the edge of the seat cushion cover all the way around, and release the
clips (A), then remove the seat cushion cover.
me
Monday, April 13, 2009 6:02:19 AM
Page 108
me
Monday, April 13, 2009 6:02:20 AM
Page 109
To prevent wrinkles, make sure the material is stretched evenly over the
pad before securing the clips.
Replace any clips (A) you removed with new ones. Install them with
commercially available upholstery ring pliers (B).
Fig. 80: Installing Clips
REAR SEAT ARMREST COVER REPLACEMENT
me
Monday, April 13, 2009 6:02:20 AM
Page 110
NOTE:
Take care not to tear the seams or damage the seat covers.
1. Remove the armrest from the seat-back (see REAR SEAT ARMREST
REPLACEMENT ).
2. Remove the armrest beverage holder from the armrest (see REAR SEAT
ARMREST BEVERAGE HOLDER REPLACEMENT ).
3. Using a 17 mm socket wrench, remove the pivot bolts, then remove the wave
washers (A), washer (B), and pivot brackets (C) from both sides of the armrest
(D).
me
Monday, April 13, 2009 6:02:20 AM
Page 111
Fig. 81: Removing Wave Washers, Washer And Pivot Brackets From Both
Sides Of Armrest With Torque Specifications
me
Monday, April 13, 2009 6:02:20 AM
Page 112
4. If necessary, remove the collars (E) from the pivot brackets.
5. Release the hooks (A) and hook strip (B), and pull back the armrest cover (C)
all the way around.
me
Monday, April 13, 2009 6:02:20 AM
Page 113
Fig. 82: Removing Rear Seat Armrest Cover
me
Monday, April 13, 2009 6:02:20 AM
Page 114
6. Release the armrest cover from the armrest pivot portions (D), then remove it
from the pad (E).
7. Install the cover in the reverse order of removal, and to prevent wrinkles, make
sure the material is stretched evenly over the pad before securing the hooks and
hook strips.
me
Monday, April 13, 2009 6:02:20 AM
Page 115

And Rear Seats Courtesy of AMERICAN HONDA

Transcription

Similar documents

Honda CB450 Restoration

Team Coaches Mainz05

BOAT SEAT - VA

ultimax.2

Page 0458

Honda City Modulo Package

The People`s Choice - Honda CX500 - CX / GL MCC • The CX

Demontering av radio-forsterker(amplituner) i Renault

2013 Class Dates - Safe Kids Grand Forks

Boeing 777-200 Re-ﬁt Long-Haul