TAC Woodsman 730 Brush Chipper Specifications

ENVIRONMENTAL
EQUIPMENT
TECHNICAL SPECIFICATIONS
TAC Woodsman 730
Brush Chipper Specifications
13” Capacity Towable Chipper, Reverse Auto Feed Governor, Top Discharge
SPECIFICATIONS
FEATURES
DIMENSIONS
Operating Weight
5,200 lbs
18” wide by 24” diameter full pocket cutting drum
Width
74”
Chipping Capacity
13”
13” high by 18” wide chipper opening
Height
105”
Gross Engine Power
84-99 hp
Programmable reverse auto feed governor
Length (operating)
212.13”
Engine Options
Kubota
Hydraulic lift and crush on feed wheel
Length: (transport)
185”
Caterpillar
300 degree hand crank swivel discharge
John Deere
Cummings
ENGINE / DRIVE
❱❱ Make/Model:
❱❱ Max hp:
❱❱ Max Torque:
❱❱ Fuel:
❱❱ Cylinders:
❱❱ Fuel Tank Capacity (gl): ❱❱ Oil Capacity (qt):
❱❱ Cooling Medium:
❱❱ Coolant Capacity (gl):
❱❱ Drive:
CUTTING SYSTEM
❱❱ Drum Size:
❱❱ Drum Speed (rpm):
❱❱ Knives:
❱❱ Anvil:
❱❱ Drum Safety Lock Positions:
FEED SYSTEM
❱❱ Infeed Opening:
❱❱ Feed Table Height:
❱❱ Feed Table Length:
❱❱ Feed Wheel Diameter:
❱❱ Feed Wheel Length:
❱❱ Feed Wheel Spring Clamp Force Avg. (lbf):
❱❱ Feed Wheel Hyd. Lift & Crush (lbf):
❱❱ Feed Rate (fpm):
❱❱ Motor Displacement (cu. In.):
❱❱ Feed Control:
❱❱ Bar Actuation Force (lbs.):
❱❱ Bar Positions:
❱❱ Yoke Safety Lock Position:
FEED SAFETY SYSTEM
❱❱ Bottom Feed Stop Bar:
❱❱ Bar Actuation Force (lbs.):
❱❱ Reset Method:
❱❱ E-Stops (Infeed Sides):
DISCHARGE SYSTEM
❱❱ Discharge Height:
❱❱ Chute Rotation:
❱❱ Rotation Type:
❱❱ Height Adjustable:
CHASSIS
❱❱ Frame:
❱❱ Hitch Type: ❱❱ Tool Box:
❱❱ Wheels:
❱❱ Tires: ❱❱ Axle:
❱❱ Brakes:
HYDRAULIC
❱❱ System:
❱❱ Hydraulic Tank Capacity (gl):
❱❱ Filtration:
❱❱ Pump (gpm):
❱❱ System Relief (psi):
ELECTRICAL
❱❱ System Voltage:
❱❱ Battery:
❱❱ Lights:
❱❱ Standard Gauges:
❱❱ Shutdown System:
WEIGHTS
❱❱ Tongue Weight (lbs):
❱❱ Operating Weight (lbs.):
DIMENSIONS
❱❱ Width:
❱❱ Height:
❱❱ Length:
❱❱ Transport Length:
Kohler V3 Series
84.5 hp @ 2,600 rpm
60.7 ft-lb @ 2,400 rpm
Diesel
4
19
13.9
Liquid
3.5
PTO Clutch / Belt
TAC Woodsman 730
24” dia. x 18” width
1,673.75 rpm
(2) Double Edged Full Pocket
4 edges, 1” Steel
2
13” x 18”
25”
70”
105”
14.125
18”
501.83
2,817.61
129.06
29.8 cu. in.
4 Postion Bar w/ Autofeed Governor
E-Stop, Forward., Stop & Reverse
1
10 Ga. Steel
34
Momentary Push Botton
Push / Pull Knob
74”
105.5”
300º
Manual (Standard Latch)
3 Position
1/4” Steel
3” PINTLE
No
LT 245/75R16
6,000 lb torsion axle
Electric w/Breakaway Switch
Open Center
12
10 Micron
4.5
2,500
212.13”
12V
12V 800 CCA
Turning, license, brake, tail & side marker, fuel, hour, voltage, water temp. oil pressure
Tachometer, Multifunction Display
High Temperature, Low Pressure
5,200
74”
105.5”
212.13”
185”
www.terex.com/environmental-equipment
Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes
only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual when
using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written
warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Products and services listed may be trademarks,
service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other countries. All rights are reserved. Terex is a registered trademark of
Terex Corporation in the USA and many other countries.
© 2011 Terex Corporation.
Terex Woodsman - 1250 Commerce Drive - Farwell, MI 48622 USA
Tel +1 (989) 588-4295 - [email protected]