Installation Instructions

Elite Instructions.indd 1
16/01/2012 15:43
Installation Instructions
Bathroom, Toilets, Utility Rooms and Kitchens
EL100, EL150U, EL150
& EL150SCPC Axial Fans
GW logo col_MASTER
Environmental
Slotvent
Slotvent
Greenwood Air Management Ltd
Environmental
Greenwood House, Brookside Avenue,
Rustington, West Sussex, BN16 3LF.
Tel: (01903) 771021 Fax: (01903) 782398
Email: [email protected]
Web: www.greenwood.co.uk
2
Read all instructions before
commencing installations
NOTES:
� Where an open-flued oil or gas- fuelled
appliance is installed in the kitchen, extract
ventilation can cause the spillage of flue
gases. Care must be taken to ensure
ventilation is reduced as appropriate, as set
out in the building regulations. The guide to
the regulations suggests that the reduced
provision should be an extract rate 20 l/s
(72 m3/h) maximum. Kitchens with solid-fuel
appliances should not have extract fans fitted.
Elite Instructions.indd 2
� The fans should not be sited where it would
be subject to a direct source of heat in excess
of 40ºC.
� For window mounting do not install fans in
opening windows. Use the correct thickness
of glass for the size of window (at least 4
mm thick) if in doubt, contact a glazier.
� A clearance of 75 mm to be allowed on both
sides of fan for the removal of the internal
grille.
16/01/2012 15:43
speed
hen or
an will
activate
ch.
verrun
switch
hing off
tch.
es of
If fan
egral
me
utility room
room ventilation.
ventilation.
utility
Types of
of controls
controls and
and operation
operation as
as follows:
follows:
Types
TYPE
TYPE EL100,
EL100, EL150U,
EL150U, EL150
EL150
Operation by
by light
light switch,
switch, remote
remote switch
switch or
or
Operation
remote
remote sensor.
sensor.
TYPE ‘PC’
‘PC’ AND
AND ‘UPC’
‘UPC’
TYPE
Operation
Operation by
by pull
pull cord.
cord.
Operation
TYPE ‘TR’
‘TR’
TYPE
Operation
Operation by
by light
light switch
switch or
or remote
remote switch.
switch.
When
wired
into
room
light
or
remote
switch
the
will
When
wiredElite
into range
room of
light
or are
remote
switch
the fan
fan
will
The
Airvac
fans
single
and dual
speed
operate whilst
whilst the
the switch
switch is
is on.
on. Switching
Switching off
off will
will activate
activate
operate
axial flow extract fans designed to exceed Building
the
timer.
the overrun
overrunrequirements
timer.
Regulation
for bathroom, toilet, kitchen or
utility
room
TYPE ‘T’
‘T’ ventilation.
TYPE
Operation
by
cord,
light
or
Types
of controls
as follows:
Operation
by pull
pull and
cord,operation
light switch
switch
or remote
remote switch.
switch.
Integral
pull
will
the
IntegralEL100,
pull cord
cord
will activate
activate
the fan
fan for
for pre-set
pre-set overrun
overrun
TYPE
EL150U,
EL150
timer
operation.
If
wired
into
room
light
or
remote switch
timer
operation.
If
wired
into
room
light
or
Operation by light switch, remote switch orremote switch
the
will
the fan
fan sensor.
will operate
operate whilst
whilst the
the switch
switch is
is on.
on. Switching
Switching off
off
remote
will
will activate
activate the
the overrun
overrun timer.
timer.
TYPE ‘PC’ AND ‘UPC’
TYPE ‘DT’
‘DT’
TYPE
Operation
by pull cord.
Automatic
Automatic operation
operation by
by light
light switch
switch or
or remote
remote switch.
switch.
TYPE
‘TR’
Pre-set
delay
timer
facility
allows
up
to
Pre-set delay timer facility allows up to two
two minutes
minutes of
of
Operation
by light
switch
or remote
switch.
fan operation
operation
before
the overrun
overrun
timer
is actuated.
actuated. If
If fan
fan
fan
before
the
timer
is
When
wiredoff
into
room
or timer
remotesetting
switchthe
theintegral
fan3will
is
after
the
delay
is switched
switched
off
after
thelight
delay
timer
setting
the
integral
operate
the operate
switch isthe
on.fan
Switching
off will time
activate
overrun
timer
for
overrun whilst
timer will
will
operate
the
fan
for the
the pre-set
pre-set
time
the
overrun timer.
period.
period.
TYPE
‘HTR’
TYPE ‘T’
‘HTR’
Operation
pull cord,
Automatic by
operation
by light
light switch
switch or
or remote
remote switch.
switch.
Automatic
operation
by
light
switch
or
remote
switch.
within the
the room
room to
to prevent
prevent ‘hunting’.
‘hunting’.
within
When wired
wired into
into room
room light
light or
or remote
remote switch
switch the
the fan
fan will
will
When
operate whilst
whilst the
the switch
switch is
is on.
on. Switching
Switching off
off will
will activate
activate
operate
the overrun
overrun timer.
timer.
the
3
TYPE ‘PIR’
‘PIR’
TYPE
Automatic operation
operation by
by an
an integral
integral passive
passive infra-red
infra-red sensor
sensor
Automatic
which controls
controls the
the fan
fan by
by detecting
detecting body
body movement
movement within
within
which
7 metres.
metres. The
The sensor
sensor picks
picks up
up the
the movement
movement and
and the
the fan
fan
7
is activated.
activated. Once
Once movement
movement ceases
ceases the
the overrun
overrun timer
timer will
will
is
run for
for the
the pre-set
pre-set time
time period.
period.
run
TYPE
‘MA’
the
RH‘MA’
is reduced back to the activation point the linked
TYPE
Dual
slow
overrun
timerautomatic
continuesoperation
to operateto
fanspeed
for theand
pre-set
Dual speed,
speed,
automatic
operation
tothe
slow
speed
and
manual
operation
to
time
period
to ensure
the RHspeed.
level is further reduced
manual
operation
to normal
normal
speed.
Integral
humidistat
operates
fan
within
room to prevent
Integralthe
humidistat
operates‘hunting’.
fan to
to slow
slow speed
speed whilst
whilst the
the
RH
(relative
humidity)
exceeds
pre-set
activation
point.
RH
(relative
humidity)
exceeds
pre-set
activation
point.
When wired into room light or remote switch the fan
will
When
is
to
pre-set
level
linked timer
When RH
RH
is reduced
reduced
to the
the
pre-set
level the
the
timer
operate
whilst
the switch
is on.
Switching
off linked
will activate
continues
fan at
continues
at slow
slow speed
speed for
for the
the nominated
nominated overrun
overrun
the
overrunfan
timer.
period, further
further lowering
lowering the
the humidity
humidity level.
level.
period,
TYPE
‘PIR’
Manual
operation by
by remote
remote switch/light
switch/light switch
switch
Manual
operation
Automatic
operation
by an integral
passive infra-red sensor
operates
the
fan
at
normal
speed.
operates
the
fan
at
normal
speed.
which controls the fan by detecting body movement within
Humidistat
adjustable
50
–– 90%
RH.
Humidistat
adjustable
50 up
90%
RH.
7
metres. The
sensor picks
the movement
and the fan
Adjustable
overrun timer
to
Adjustable
timer (up
(upceases
to 30mins).
30mins).
is
activated.overrun
Once movement
the overrun timer will
TYPE
run
for‘SCPC’
the pre-set time period.
TYPE
‘SCPC’
Operation
by pullcord or remote switch.
Operation
TYPE
‘MA’by pullcord or remote switch.
Single speed
speed operation
operation at
at pre-set
pre-set rate
rate for
for use
use where
where
Single
Dual speed, automatic operation
to slow
speed
and
open
gas
are present.
open flued
flued
gas appliances
appliances
present. At
At installation
installation
manual
operation
to normalare
speed.
the
variable
speed
control
is
set
and
sealed
to
prevent
the variable
speed control
set to
and
sealed
to whilst
preventthe
Integral
operatesis fan
slow
speed
spillage humidistat
from gas
gas appliance.
appliance.
spillage
from
RH
(relative
humidity)
exceeds pre-set activation point.
When RH is reduced to the pre-set level the linked timer
continues fan at slow speed for the nominated overrun
period, further lowering the humidity level.
Integral
cord humidity
will activate
the will
fan for
pre-set
The fans
fanspull
integral
humidity
sensor
will
operate
theoverrun
fan
The
integral
sensor
operate
the
fan
timer
If wiredthe
into
room activation
light or remote
whilstoperation.
the RH
RH exceeds
exceeds
the
pre-set
activation
point,switch
When
whilst
the
pre-set
point,
When
the fan
operateback
whilst
is on.
Switching
off
RH will
is reduced
to the
the switch
activation
point
the linked
Manual operation by remote switch/light switch
will
activate
overrun to
timer.
overrun
timerthe
continues
operate the fan for the pre-set
operates the fan at normal speed.
time period to ensure the RH level is further reduced
TYPE ‘DT’
Humidistat adjustable 50 – 90% RH.
within the room to prevent ‘hunting’.
Automatic operation by light switch or remote switch.
Adjustable overrun timer (up to 30mins).
When wired into room light or remote switch the fan will
Pre-set delay timer facility allows up to two minutes of
TYPE ‘SCPC’
operate whilst the switch is on. Switching off will activate
fanSee
operation
before the overrun
timer is actuated.
Iffor
fanfurther details.
�
Sensor
Adjustments
section
Operation by pullcord or remote switch.
theSee
overrun
timer.// Timer
�
Sensor
Timer
Adjustments
section
for
further
details.
is switched off after the delay timer setting the integral
Single speed operation at pre-set rate for use where
overrun
timer
will
operate
the
fan
for
the
pre-set
time
TYPE
‘PIR’
The Airvac
Airvac Elite
Elite range
range of
of fans
fans are
are fitted
fitted with
with
electrical
operated
anti-backdraught
� The
electrical
operated
anti-backdraught
�
open
flued gas appliances
are present.
At installation
period.
Automatic operation by an integral passive infra-red sensor
shutters which
which have
have a
a time
time delay
delay to
to open
open or
or
close.
theclose.
variable speed control is set and sealed to prevent
shutters
which controls the fan by detecting body movement within
TYPE ‘HTR’
spillage from gas appliance.
7 metres. The sensor picks up the movement and the fan
Automatic operation by light switch or remote switch.
is activated. Once movement ceases the overrun timer will
The
fans
sensor will operate the fan
run for
theintegral
pre-sethumidity
time period.
whilst the RH exceeds the pre-set activation point, When
TYPE ‘MA’
Dual speed, automatic operation to slow speed and
manual operation to normal speed.
Integral humidistat operates fan to slow speed whilst the
RH (relative humidity) exceeds pre-set activation point.
When RH is reduced to the pre-set level the linked timer
continues
fan at slow
speed
for the nominated
overrun
�
See Sensor
/ Timer
Adjustments
section
for further
period, further lowering the humidity level.
details.
Theoperation
AirvacbyElite
range
of fans
�
Manual
remote
switch/light
switchare fitted with electrical operated anti-backdraught
operates
the fanwhich
at normal
speed.a
shutters
have
time delay to open or close.
Humidistat adjustable 50 – 90% RH.
Adjustable overrun timer (up to 30mins).
TYPE ‘SCPC’
Operation by pullcord or remote switch.
Single speed operation at pre-set rate for use where
open flued gas appliances are present. At installation
the variable speed control is set and sealed to prevent
from gas 3appliance.
Elitespillage
Instructions.indd
16/01/2012 15:43
Elite Instructions.indd 4
16/01/2012 15:43
Elite Instructions.indd 5
16/01/2012 15:43
6
Wall Mounting
External Grille
Ducting
EL100/EL150
Elite Instructions.indd 6
16/01/2012 15:43
7
1
2
A
Ø
Ø
A
ED1
Ø = 125 mm
ED150 Ø = 180 mm
ED1
Ø = 125 mm
ED150 Ø = 180 mm
3
4
5
6
7
8
Make sure rubber cable
grommet is fitted onto
cable before threading
cable through fan
backplate.
Push fit the four screw
cover plugs provided,
with hollow end facing
outwards if fixing to wall
using outer mounting points.
SEE PAGE 10 FOR WIRING INSTRUCTIONS
Elite Instructions.indd 7
16/01/2012 15:43
EG1/RAB
Elite Instructions.indd 8
16/01/2012 15:43
Elite Instructions.indd 9
16/01/2012 15:43
10
Wiring Details for Fan Isolator Only
1
2
25 mm
1
Rear of block
2–Wire Connection
2
L1
6 mm
N
L
25 mm
3
1
2
3–Wire Connection
35 mm
3
Front
of block
L
4
N
L1
5
6
7
8
Elite Instructions.indd 10
16/01/2012 15:43
11
Wiring Diagrams
The electrical connections must be carried out
by a qualified electrical engineer in accordance
with Part P of the Building Regulations & IEE
Wiring Regulations.
WARNING: Isolate electricity supply before
starting work.
The fans are double insulated and do not
require an earth connection.
For single units use 3 amp fuse.
When supplied from a 5 amp lighting circuit
no local fuse is required.
Specification:
230 V~50 Hz.
Refer to fan rating label for watts consumption.
Cable Sizes: 2 or 3 core.
0.75 mm2 and 1.00 mm2 flexible.
INSTALLATION IN AREAS REQUIRING IPX4
PROTECTION:
Mains cable section should be round, with an
outside diameter between 5.5 mm to 8.5 mm.
This will ensure sealing at the cable entry
grommet.
Fan
Terminals
Fan
Terminals
Fan
Terminals
L
L
L
L
N
N
L
L
Light
N
N
L1
Optional
Light
N
N
L1
Optional
Light
L1
Optional
X
External
wiring for remote switch / light switch:
X
Models:
EL100,
EL150U,
EL150
&
EL150SCPC
External
wiring
for
remote
switch
/
light
switch:
X
External
wiring for remote switch / light switch:
Models:
EL100,
EL150U,
EL150
EL150SCPC
External
wiringEL150
for
remote
switch&/ light
switch:
Models:
EL100,
& EL150SCPC
Models: EL100, EL150U, EL150 & EL150SCPC
Remote /
Light
Switch
Remote
/
Light
Switch
Remote
/
3 Amp Fuse
Light Switch
Fan
Terminals
Fan
Terminals
Fan
Terminals
L
L
N
N
L
N
N
Light
L
L1
optional
N
N
Light
Light
L
L1
Light
Switch
Light
L1
XL
External
wiring
forfor
operation
room light:
Light
Switch
Lightcordwith
External
wiring
pull
operation
in parallel
X
Models:
TR,
HTRfor
& Switch
MA cord
with
room
light:
Models:
T
External
wiring
pull
operation
in
parallel
X
with
roomwiring
light: for
Models:
T operation in parallel
External
pull cord
with room light: Models: T
Fan
Terminals
Fan
Terminals
Fan
Terminals
L
L
N
N
L
N
N
L
L1
N
N
Light
Operating
L
L1
SwitchPC &Light
External
wiring: Models:
SCPC
Operating
L1
XL
Switch
Operating
External
wiring for
operationLight
with room light:
X
Switch
Models:
DT,
TR,
HTR,
UHTR
&
MA
External
wiring for operation with room light:
X
Models:
TR,for
HTR,
UHTR &with
MA room light:
External DT,
wiring
operation
Models: DT, TR, HTR, UHTR & MA
3 Amp Fuse
Fan
Terminals
Fan
Terminals
Fan
Terminals
L
L
L
L
N
N
L
L
N
N
L1
N
N
L1
X
L1
External
wiring: Model: PIR, PC, UPC & SCPC
X
External
wiring: Model: PIR, PC, UPC & SCPC
X
External wiring: Model: PIR, PC, UPC & SCPC
Controller
Terminals
Controller
Terminals
Controller
Terminals
1
L
L
1
L
L
2
1
2
NL
NL
3
2
N
N
3
N
XN
3
External
wiring: Model: AX150 REV
X
External
wiring: Model: AX150 REV
X
Elite Instructions.indd 11
Fan
Terminals
Fan
Terminals
Fan
Terminals
1
1
2
1
2
3
2
3
3
16/01/2012 15:43
12
Sensor/Timer Adjustments
1
2
3
4
Model: MA only
–T
ime
Clockwise to
increase and anticlockwise to decrease time.
5
r+
–H
Clockwise to
um
increase and antiid +
clockwise to decrease time
or humidity sensor sensitivity.
6
Model: HTR only
90%
50%
Clockwise to increase and anti-clockwise to
decrease time or humidity sensor sensitivity.
Model SCPC adjustments, see additional information supplied with fan.
To clean or service fan
�
Remove grille: Lever off at side using coin or screwdriver.
�
Undo screws (exposed by removal of grille), and pull the fan away from its back plate.
The fan may now be cleaned using a brush or damp cloth. DO NOT IMMERSE IN WATER.
WARNING: On no account should the interior of the fan be cleaned until the unit has been
removed from its back plate or isolated from the mains.
BP8631
Elite Instructions.indd 12
P570-75 IssD
June
2006
05-10-155
P570-75
IssD
June 2008
05-10-155
MCR 706
IssE
January
2012
05-10-155
16/01/2012 15:43