D-NE20/NE20LS - Philips Parts and Accessories

Transcription

D-NE20/NE20LS - Philips Parts and Accessories
D-NE20/NE20LS
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
Ver. 1.1 2005.01
D-NE20
E Model
D-NE20/NE20LS
Australian Model
D-NE20
Chinese Model
D-NE20LS
Tourist Model
Photo : RED
D-NE20
Model Name Using Similar Mechanism
NEW
CD Mechanism Type
CDM-3325ERV
Optical Pick-up Name
DAX-25EV
SPECIFICATIONS
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 770 - 800 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the objective lens surface on the
optical pick-up block with 7 mm aperture.)
Headphones (stereo minijack)
Approx. 5 mW + Approx. 5 mW at 16 kΩ
(Approx. 1.5 mW + Approx. 1.5 mW at 16 kΩ)*
*For the customers in Europe
Optical digital output (optical output connector)
Output level: –21- –15 dBm
Wavelength: 630 - 690 nm at peak level
D-A conversion
1-bit quartz time-axis control
Power requirements
• Sony NH-14WM rechargeable battery:
1.2 V DC × 1
• LR6 (size AA) battery: 1.5 V DC × 1
• AC power adaptor (DC IN 3 V jack)
• Rated current: 1 A
Frequency response
20 - 20 000 Hz +1
-2 dB (measured by JEITA)
Operating temperature
5°C - 35°C (41°F - 95°F)
Output (at 3 V input level)
Line output (stereo minijack)
Output level 0.7 V rms at 47 kΩ
Recommended load impedance over 10 kΩ
Dimensions (w/h/d) (excluding projecting parts
and controls)
Approx. 127 × 13.1 × 132.5 mm (5 × 1732 × 5 1 4 in.)
Mass (excluding accessories)
Approx. 116 g (4.1 oz.)
Supplied accessories
• AC power adaptor
• Charging stand
• External battery
• Rechargeable battery
case with cover
• Battery carrying case
• Carrying pouch
• Earphones
• Remote control
• CD-ROM (SonicStage)
• Operating instructions
• Installation/Operating Guide
• AC plug adaptor (Supplied with tourist model)
US and foreign patents licensed from Dolby
Laboratories.
Design and specifications are subject to change
without notice.
PORTABLE CD PLAYER
9-879-267-02
2005A16-1
© 2005.01
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
D-NE20/NE20LS
CAUTION
• INVISIBLE LASER RADIATION
WHEN OPEN
• DO NOT STARE INTO BEAM OR
VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS
• CLASS 1M INVISIBLE LASER
RADIATION WHEN OPEN
• DO NOT VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
On AC power adaptor
• Use only the AC power adaptor supplied.
If your CD player is not supplied with the
one, use the AC-E30HG AC power
adaptor. Do not use any other AC power
adaptor. It may cause a malfunction.
Polarity of the plug
• Do not touch the AC power adaptor with
wet hands.
• Connect the AC power adaptor to an easily
accessible AC outlet. Should you notice an
abnormality in the AC power adaptor,
disconnect it from the AC outlet
immediately.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
• To clean the terminals
If the terminals on the charging stand become
dirty, the battery may not be charged properly.
Clean the terminals with a cotton swab or a
dry cloth periodically as illustrated below.
Terminals
D-NE20/NE20LS
You can play discs on this CD player.
Audio CDs:
CD-DA format CDs
CD-DA (Compact Disc Digital Audio) is a recording standard used for Audio CDs.
ATRAC CDs:
CD-R/CD-RW on which audio data compressed in the ATRAC3plus format
has been recorded by using SonicStage*
ATRAC3plus (Adaptive Transform Acoustic Coding3plus) is audio compression
technology that satisfies the demand for high sound quality and high compression
rates. ATRAC3plus can compress audio files to about 1/20 of their original size at 64
kbps.
Bit rates and sampling frequencies this CD player can play are:
ATRAC3
ATRAC3plus
Bit rates
66/105/132 kbps
48/64/256 kbps
Sampling frequencies
44.1 kHz
44.1 kHz
Up to 62 characters can be displayed on this CD player.
MP3 CDs:
CD-R/CD-RW on which audio data compressed in the MP3 format has
been recorded by using a software other than SonicStage*
Bit rates and sampling frequencies this CD player can play are shown below. Variable
Bit Rate (VBR) files can also be played.
MPEG-1 Layer3
MPEG-2 Layer3
MPEG-2.5 Layer3
Bit rates
32 - 320 kbps
8 - 160 kbps
8 - 160 kbps
Sampling frequencies
32/44.1/48 kHz
16/22.05/23 kHz
8/11.025/12 kHz
This CD player conforms to Version 1.0/1.1/2.2/2.3/2.4 of the ID3 tag format. ID3 tag
is a format for adding certain information (track name, album name, artist name, etc.)
to MP3 files. Up to 64 characters of ID3 tag information can be displayed on this CD
player.
CD-Extra and Mix-Mode CDs:
CD-R/CD-RW on which CD-DA format data and CD-ROM format data are
recorded together.*
If you cannot play your CD, change the "CD-EXTRA" setting in the OPTION menu.
Then you may play your CD.
An ATRAC CD on which audio data compressed in the MP3 format has been recorded
using software other than SonicStage can also be played.
With SonicStage, you cannot create a CD on which mixed format audio data is recorded.
* Only ISO 9660 Level 1/2 and Joliet extension format discs can be played.
Music discs encoded with copyright protection technologies
This product is designed to play back discs that conform to the Compact Disc (CD)
standard. Recently, various music discs encoded with copyright protectiontechnologies
are marketed by some record companies. Please be aware that among those discs,
there are some that do not conform to the CD standard and may not be playable by
this product.
TABLE OF CONTENTS
1.
SERVICING NOTES ................................................ 4
2.
GENERAL ................................................................... 5
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
Disassembly Flow ...........................................................
Lid Upper Assy ................................................................
Cabi Mid Sub Assy ..........................................................
EGH Board, JACK Board, JACK SUB Board,
CD Mechanism Deck (CDM-3325ERV) .........................
3-5. Window (LED), Button (Control) ...................................
3-6. Turn Table Motor Assy (M901),
Sled Motor Assy (M902),
Optical Pick-up (DAX-25EV) .........................................
6
7
8
9
10
10
4.
ELECTRICAL CHECKING .................................... 11
5.
DIAGRAMS
5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7.
Block Diagram ................................................................
Printed Wiring Board – EGH Board (Side A) – .............
Printed Wiring Board – EGH Board (Side B) – .............
Schematic Diagram – EGH Board (1/3) – ......................
Schematic Diagram – EGH Board (2/3) – ......................
Schematic Diagram – EGH Board (3/3) – ......................
Printed Wiring Board – JACK Board (Side A),
JACK SUB Board, SUB Board – ....................................
5-8. Printed Wiring Board – JACK Board (Side B) – ............
5-9. Schematic Diagram – JACK Board,
JACK SUB Board, SUB Board – ...................................
6.
13
14
15
16
17
18
19
20
21
EXPLODED VIEWS
6-1. Overall Assy .................................................................... 27
6-2. Cabinet (Lower) Section .................................................. 28
6-3. CD Mechanism Section (CDM-3325ERV) ..................... 29
7.
ELECTRICAL PARTS LIST .................................. 30
3
D-NE20/NE20LS
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S501. (push switch type)
The following checking method for the laser diode is operable.
• Method:
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. With a disc not set, turn on the S501 with a screwdriver having
a thin tip as shown in Fig.1.
3. Press the u button.
4. Observing the objective lens, check that the laser diode emits
light.
When the laser diode does not emit light, automatic power
control circuit or optical pickup is faulty.
In this operation, the objective lens will move up and down 4
times along with inward motion for the focus search.
lever (lid detection)
S501
JACK BOARD
lever (lid detection)
Fig. 1 Method to push the S501
4
D-NE20/NE20LS
SECTION 2
GENERAL
This section is extracted
from instruction manual.
Ȣ4ERMINALSFORTHECHARGINGSTANDEXTERNAL
'UIDETO0ARTSAND
#ONTROLS
BETTERYCASEAPAGE
ȣ ¼ÊBUTTONSAPAGE
Ȥ#$0LAYER
ýSTOP#('BUTTONAPAGE
#$PLAYER
2EMOTE
ýSTOPBUTTONAPAGE
ȥ úPLAYPAUSE
BUTTONAPAGE
Ȧ(/,$SWITCHONTHEBACKOFTHE#$
PLAYERAPAGE
ȧ/0%.SWITCHAPAGE
Ȩ
GROUPnBUTTONSAPAGE
ȩ#$0LAYER
6/,6OLUMEnBUTTONSAPAGE
2EMOTE
6/,6OLUMEnCONTROL
APAGE
Ȫ ¦HEADPHONES,).%/54/04)#!,
2EMOTE
JACKAPAGE
ȫ/02/PERATIONLAMPAPAGE
Ȭ/PERATIONDIALAPAGE
ȭ3%!2#(BUTTONAPAGE
Ȯ&UNCTIONBUTTONAPAGE
ȯ&UNCTIONDIALAPAGE
Ȱ#LIPAPAGE
4HISBUTTONHASATACTILEDOT
Remote display
Tourist model
except Tourist models
ȱ$ISCINDICATORAPAGE
ȳ$ISCINDICATORAPAGE
Ȳ#HARACTERINFORMATIONDISPLAYAPAGE
ȴ4RACKNUMBERINDICATOR!UTORANKINGPLAYINDICATORAPAGE
ȳ0LAYMODEINDICATORAPAGE
ȵ#HARACTERINFORMATIONDISPLAYAPAGE
ȴ3OUNDINDICATORAPAGE
ȶ0LAYMODEINDICATORAPAGE
ȵ"ATTERYINDICATORAPAGE
ȷ3OUNDINDICATORAPAGE
ȶ'ROUPINDICATORAPAGE
ȸ"ATTERYINDICATORAPAGE
ȷ0LAYLISTINDICATORAPAGE
ȹ'ROUPINDICATORAPAGE
ȸ"OOKMARKINDICATORAPAGE
Ⱥ0LAYLISTINDICATORAPAGE
Ȼ"OOKMARKINDICATORAPAGE
5
D-NE20/NE20LS
SECTION 3
DISASSEMBLY
Note: Disassemble the unit in the order as shown below.
3-1. DISASSEMBLY FLOW
SET
3-2. LID UPPER ASSY
(Page 7)
3-3. CABI MID SUB ASSY
(Page 8)
3-4. EGH BOARD, JACK BOARD,
JACK SUB BOARD,
CD MECHANISM DECK
(CDM-3325ERV)
(Page 9)
3-5. WINDOW(LED),
BUTTON(CONTROL)
(Page 10)
3-6. TURN TABLE MOTOR ASSY(M901),
SLED MOTOR ASSY(M902),
OPTICAL PICK-UP(DAX-25EV)
(Page 10)
6
D-NE20/NE20LS
Note: Follow the disassembly procedure in the numerical order given.
3-2. LID UPPER ASSY
2 two screws (upper lid)
3 bracket (hinge R)
4 bracket (hinge L)
1 Push two knobs and
open the lid upper.
5 Close the cover until the tip of the cover of the
top cover assembly is left open by 5 mm,
then slide the top cover assembly in the
direction of the arrow.
8 lid upper assy
6
7
7
D-NE20/NE20LS
3-3. CABI MID SUB ASSY
spring (lock claw)
2 eight screws
1 screw
open knob (R)
open knob (L)
7 cabi mid sub assy
4 open knob (L)
3 spring (lock claw)
6 spring (upper lid)
5 open knob (R)
battery terminal board (+)
Note: It is recommended to visually check that the battery terminal board (+) is
installed in the specified position after assembling the cabi mid sub assy
because, in some cases, the battery terminal board (+) cannot be housed
when assembling the cabi mid sub assy.
8
D-NE20/NE20LS
3-4. EGH BOARD, JACK BOARD, JACK SUB BOARD, CD MECHANISM DECK (CDM-3325ERV)
7 two insulators
8 CD mechanism deck
(CDM-3325ERV)
2 connector (2pin)
1 connector (4pin)
7 insulator
5 flexible board (CN601)
6 EGH board
4
qs Remove solder of the JACK board.
0 JACK board
qa battery terminal
board (–)
3 connector (3pin)
qd SUB board
(battery terminal board (+))
9 Remove solder of the JACK board.
assembly: the cable pass on three claws.
qg JACK SUB board
qf three claws
9
D-NE20/NE20LS
3-5. WINDOW (LED), BUTTON (CONTROL)
1 screw
2 window (led)
3 button (control)
3-6. TURN TABLE MOTOR ASSY (M901), SLED MOTOR ASSY (M902), OPTICAL PICK-UP (DAX-25EV)
1 three screws
(B 1.7 × 4)
2 gear cover
4 optical pick-up (DAX-25EV)
3 sled motor assy (M902)
5 three screws
(B 1.7 × 4)
6 turn table motor assy (M901)
10
D-NE20/NE20LS
SECTION 4
ELECTRICAL CHECKING
The CD section adjustments are done automatically in this set.
In case of operation check, confirm that RF level.
Precautions for Check
1. Perform check in the order given.
2. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise
indicated.
3. Power supply voltage requirement : DC1.5V in battery terminals.
VOLUME button
HOLD switch
: Minimum
: OFF
Checking Location:
[EGH BOARD] (SIDE B)
TP608
(RF)
IC604
TP602
(GND A)
RF Level Check
Condition:
• Hold the set in horizontal state.
Connection:
Oscilloscope
(AC range)
EGH board
TP608 (RF)
TP602 (GND A)
2 kΩ
+
–
Procedure:
1. Connect the oscilloscope to the test points TP608 (RF) and
TP602 (GND A) on the EGH board.
2. Set a disc. (YEDS-18)
3. Press the u button.
4. Check the oscilloscope waveform is as shown below.
A good eye pattern means that the diamond shape (◊) in the
center of the waveform can be clearly distinguished.
RF Signal reference Waveform (Eye Pattern)
VOLT/DIV : 100 mV (With the 10:1 probe in use)
TIME/DIV : 500 ns
RF level
0.55 to 0.6 Vp-p
To watch the eye pattern, set the oscilloscope to AC range and
increase the vertical sensitivity of the oscilloscope for easy
watching.
5. Stop revolving of the disc motor by pressing the x button.
11
D-NE20/NE20LS
SECTION 5
DIAGRAMS
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
Note on Printed Wiring Boards.
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• These boards are multi-layer printed board. However, the paterns
of intermediate-layer have not been included in the diagram.
• Waveforms
– EGH Board –
1
TP608 (RF)
540 mVp-p
200 mV/DIV, 400 ns/DIV
2
IC603 <z/b> EXTAL
3.0 Vp-p
44.1 ns
1 V/DIV, 20 ns/DIV
12
Note on Schematic Diagrams.
• All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or
less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
•
f
: internal tolerance.
• C : panel designation.
Note: The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Total current is measured with CD installed.
• Power voltage is dc 1.5 V and fed with regulated dc power supply
from battery terminals.
• Voltages and waveforms are dc with respect to ground in playback
mode.
no mark : CD PLAY
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J
: CD
c
: DIGITAL OUT
• Abbreviation
CH
: Chinese model
EE
: East European model
JE
: Tourist model
KR
: Korean model
D-NE20/NE20LS
5-1. BLOCK DIAGRAM
IC603
SYSTEM CONTROLLER
VCC1
DOUT 84
J301
PF6/DBG6/X PLUG DTC 128
IC606
+2V REG
AOUTL 102
AOUTR 97
2V
IC3007
HP AMP
SENB 10
106 XTAN
SDATA 12
X601
105 EXTAL
22.579MHz
SCLK 11
RFOUT 15
75 P17/AIFBCK
DETECTOR
FE(A)
SE(B)
168 FRDR
F12 43
165 TFDR
R12 44
166 TRDR
A1-A19
237
255
F11 47
163 SFDR
R11 48
164 SRDR
F-
28 RO3
T+
21 FO2
PWM 35
T-
24 RO2
SYNC 33
S+
13 FO1
COLDST 37
S-
17 RO1
12 CPV1
8 CPU1
107 CPW1
11 COM
9 UO
6 VO
4 WO
COM
U
V
W
26-29,
32-35,
38,39, D0-D15
41,42,
44-47
240
D0-D-15
APWM 34
169 MDP
171 C176
IC604
S-RAM
12,13,
15,16,
SDDQ16 18,19,
21,22,
SDDQ1 25-28,
30,31,
34,36,
SDA11
SDA0
181 PG7
DATA 36
177 PC1/SO0
CLOCK 30
178 PC0/SCK0
FG 23
214 PD2/INT2/ECIN
IC602
EEPROM
SCK 6
2,3,5,
6,8,9,
11,12, DQ16
39,40, DQ1
42,43,
45,46,
48,49,
IC402
POWER
CONTROLLER
19
51,52,
57,58,
60,61,
63,64,
66,67,
69,70,
XSDWE
SOUDQW
XSDCAS
XSXCS
XSDRAS
SDCLK
SDCKE
SDUDQW
22 A19
31 CE
37 OE
24
. A11
27 A0
32
15
14
16
18
17
35
34
36
33
40
41
42
44
47
45
48
XWE
LDQW
XCAS
XCS
XRAS
CLK
CKE
UDQW
IC401(2/2)
POWER CONTROL
27 VM3
25 VM23
22 VM2
VCC1
DI 5
DO 2
XCS 1
176 PC2/SI0
VCC2
4 PE3
S503,504,506,508,510
FUNCTION
KEY
129 218 238
78
77 185 197
8
212
PD4/INT4
M901
SPINDLE
MOTOR
26 FO3
1,2
5-8,
11-15, A0-A15
17-20,
23-25,
30
PE2/DTCK
M902
SLED M
MOTOR
R13 41
199 AN2
XRST 204
• R-CH is omitted due to same as L-CH.
• Signal Path
PG5
PG6
AN7
WAKE
PF2/DBG2
AN0
PC3/XCS0
S505,507,509
FUNCTION
KEY
VCC2
IC605
P2ROM
89 PAPC
F+
TRACKING
COIL
167 FFDR
Q302,303
MUTING CONTROL
JE, HK, KR, CH
219
F13 42
Q304,305
MUTING
CONTROL
7 VDD0
8 VDD0
Q402,403
VDD CONTROLLER
AN4
63 VAPC
IC403
BUFFER
P15
LD
Q406
SWITCH
VG
IC401(1/2)
COIL/MOTOR DRIVER
PD
FOCUS
C0IL
RFAC
RFDC
FE(A)
SE(B)
CE(E)
TE(F)
PG3
VCC1
Q307
MUTE
OUT1 6
1 MCK
11 EN2
4 EN1
P14/AIFPCMD
VCC
LASER
DIODE
151
144
139
140
142
141
3 IN1
R-CH
NRD
RF
A
B
E
F
PWML 111
PWMR 112
DAMPCLK 109
PJ7/MON7(MON CK) 85
PJ6/MON6(MONDO) 86
NCS1
17 RFIN
R-CH
PF7/DBG7/X METAL DTC 127
IC601
RF AMP
OPTICAL PICK-UP
BLOCK
(DAX-25EV)
Q306
MUTE
R-CH
ADDSEL0
VCC3
LINEOUT
(OPTICAL)
183
182
194
202
132
201
175
200 AN1
Q601
LED DRIVER
LED2
LED1
3 VD B
2 VD T
Q404
SWITCH
BATM1 67
PWRSW1 78
5 RSTB
PWRSW2 81
55 CHGWON
Q402
REG
CRF 54
XADEVENT 203
IC401
4
KEY CONTROLLER
38 WAKE
Q403
CHARGE
SWITCH
32 LATCHB
S502
> HOLD
: DIGITAL OUT
D501
OPR
D-NE20/NE20LS
13
13
CHGSW 49
Q602
SWITCH
W401 RECHARGEABLE
BATTERY
NH-14WM
W402
1PCS. 1.2V
DCIN 64
Q401
SWITCH
OFF
Q401
SWITCH
J401
(FOR STAND CHARGER)
VIN
ON
1
S501
(OPEN/CLOSE)
: CD
AN6 195
Q405
SWITCH
CINW 53
VIN34 61
VO2 66
VIN12 70
74 VCC1
SW 101
98 VCC1
VM-U 10
VM-VW 7
VIN 105
66 VCC2
97 VCC2
39 RMCRB
RS 50
J402
(FOR STAND CHARGER)
D-NE20/NE20LS
5-2. PRINTED WIRING BOARD – EGH BOARD (SIDE A) –
:Uses unleaded solder.
OPTICAL PICK-UP
BLOCK
(DAX-25EV)
EGH BOARD (SIDE A)
IC606
JE, HK, KR, CH
A
IC601
* IC603
*CSP
JACK
BOARD
CN9002
(Page 19)
(Chip Size Package)
* IC605
*CSP
R622
IC3007
(Chip Size Package)
IC602
IC403
AEP, UK, EE
EXCEPT
AEP, UK, EE
11
1-863-862- (11)
• Semiconductor
Location
Ref. No.
Location
IC403
IC601
IC602
IC603
IC605
IC606
IC3007
D-4
C-9
D-8
C-7
C-10
A-7
D-3
Q601
C-5
D-NE20/NE20LS
14
14
D-NE20/NE20LS
5-3. PRINTED WIRING BOARD – EGH BOARD (SIDE B) –
:Uses unleaded solder.
(RF)
EGH BOARD (SIDE B)
IC604
* IC401
*CSP
(Chip Size Package)
5
IC402
1
(GND A)
R621
3
4
11
R624
R625
1-863-862- (11)
C631
R616
C617
• Semiconductor
Location
D-NE20/NE20LS
15
15
Ref. No.
D401
D405
Location
C-8
A-8
IC401
IC402
IC604
C-9
C-8
B-3
Q401
Q402
Q403
Q404
Q405
Q406
Q602
D-8
C-6
D-7
B-8
B-8
B-7
C-6
D-NE20/NE20LS
5-4. SCHEMATIC DIAGRAM – EGH BOARD (1/3) –
17
Q405
QS6K1
C431
47
6.3V
C450
1
R414
4.7k
L409
Q404
QS6K1
R423
4.7k
L402
L405
CN9001
50P
C423
47
6.3V
C439
0.22
C410 0.01
C409 0.01
TP618
C416
0.22
C435
4.7
R405
100k
C417
0.22
R401
100k
Q401
DTC115TE-TL
C415 0.01
R435 47k
C402
0.01
C424
0.22
C401 0.1
R402 100k
R408
100k
D405
MA785-(TX),SO
L408
C434
2.2
C432
10
IC401
SC901590VAR2
C418 0.1
R430 1M
C419 0.01
R432 1k
21
C420
0.1
18
C421 1
C449
100p
R421
100k
R431 1M
C405
0.047
R417 100
R436
1k
R404
1M
L406
C447
1
L410
R424 1M
C444
47
6.3V
R437 1k
L403
L401
C412 0.1
C408
0.22
R409
47k
C411 0.1
R428
47k
C422
1
R427
2.2M
R426
47k
C413
0.01
C445
0.1
R429
22k
C414
4700p
C446
1
R446
10k
TP403
VCC1
R406
0
L407
R407
0
TP405
VIN
C437
47
6.3V
C441
0.1
C427
22
6.3V
C442
0.1
C426
47
6.3V
TP404
P_GND
FB402
0
D-NE20/NE20LS
16
16
C443
0.1
C429
22
6.3V
C430
47
6.3V
C448
0.1
C428
10
6.3V
C440
47
6.3V
FB401 0H
L404
D-NE20/NE20LS
• See page 12 for Waveforms.
TP601
OPGSW
• See page 22 for IC Block Diagram.
R628
2.2k
R602 10k
TP604 OPSTB
R624 10k
R629
2.2k
R623
10k
R608 47k
R634
10k
C649
0.47
C650
4700p
RB601
22k
C653
0.47
C654
0.1
R637
220k
C602
470p
R655
100k
R649
22k
R642 47k
R639 47k
R610
22k
C603
1
C610
1
C626 1
C617
4700p
C618
4700p
C631
0.1
R616
470k
C609
2200p
C646
0.1
R620 47k
TP627
ADDSEL_1
R609 22k
IC606
XC6213B212NR
C605
0.22
CN601
15P
R618
1k
R636
100k
C627 22 6.3V
R625
10k
C607
0.01
C629 0.1
R617
10k
R621 1k
R603
10
C695
4700p
R650 100k
R651 100k
R601
Q602
220k 2SA1832FV
R615 (TH3SONY)
220k
C619
4700p
TP602
GND_A
C608 22p
C694 0.1
C648
0.1
C614 0.047
TP608
RF
C601
22
6.3V
• See page 22 for IC Pin Function Description.
R635 1M
5-5. SCHEMATIC DIAGRAM – EGH BOARD (2/3) –
C659
0.1
Q601
XP4214-TXE
TP621
PD7
TP609 TEST
TP630
ADDSEL_0
TP611
PD5
R614 0
C612 0.1
TP610
PD1
C611
0.01
R653 10k
R611
0
C604
0.1
C606
0.01
IC601
CXD9839K-G
C613
0.1
X601
22.579MHz
R613 0
C680
6p
C667
0.1
C681 6p
R644
R606 0
47
IC603
CASINO1
C664
47
6.3V
18
C678
22
6.3V
C677
0.1
R604 220k
EXCEPT
AEP, UK, EE
TP622 MON1
TP623 MON2
TP624 MON3
TP625 MON4
TP626 MON5
TP607
EXT_FLASH&SRAM_V
R622 220k
AEP, UK, EE
TP629
PI1
R612
100k
C676 0.1
TP617
VCC2
TP612
SK
TP614
DO
TP615
CS
TP616
GND
TP613
DI
C639
0.1
C645
0.22
TP619
AK6510CL-L
TP620
IC602
16
D-NE20/NE20LS
17
17
D-NE20/NE20LS
5-6. SCHEMATIC DIAGRAM – EGH BOARD (3/3) –
• See page 22 for IC Block Diagrams.
JE, HK, KR, CH
C404
100
6.3V
R403
100k
C403
10
IC604
MSM56X16160F-20T
L412
IC605
MR27T1602F
FB101
0H
D401
RB521S-30FTE61
C103
220
4V
IC402
NCP1400ASN22T1G
C687 0.1
R302 100
R418
22k
R101 100
C438
1
C689 0.1
IC3007
NJU8713V-TE2
R102
100k
R607 0
Q403
EMT1T2R
R419
1k
R415
100
R202
100k
R412
2.2k
R411
10k
R410
47k
R413
10k
Q402
EMX1T2R
R420
10k
C433
0.047
C3089
0.1
C201
1
C436
IC403
0.47
LMV301MGX/NOPB
C425 1
C102
100
4V
Q406
DTA115TE
17
C686
47
6.3V
16
C202
220
4V
R619 0H
FB201
0H
R201
100
D-NE20/NE20LS
18
18
D-NE20/NE20LS
:Uses unleaded solder.
5-7. PRINTED WIRING BOARD – JACK BOARD (SIDE A), JACK SUB BOARD, SUB BOARD –
TP9007
D501
JACK BOARD (SIDE A)
• Semiconductor
Location
OPR
S501
(OPEN/CLOSE)
SUB BOARD
J301
2 / LINE OUT
(OPTICAL)
A
EGH BOARD
CN9001
(Page 14)
11
1-864-413- (11)
IC401
1
6
3
4
JACK SUB BOARD
D401
RECHARGEABLE
BATTERY
NH-14WM
1.2V 1350mAh
11
1-864-412- (11)
J401
(FOR STAND CHARGER)
J402
(FOR STAND CHARGER)
M901
SPINDLE
MOTOR
M902
SLED
MOTOR
11
1-864-411- (11)
D-NE20/NE20LS
19
19
Ref. No.
Location
D401
D402
D501
D901
D903
D905
D906
F-8
E-8
A-3
B-3
C-3
F-7
F-8
IC401
E-7
Q301
Q302
Q306
Q307
Q401
Q402
Q403
B-4
C-4
B-3
B-3
E-7
F-8
E-6
D-NE20/NE20LS
Ver. 1.1
5-8. PRINTED WIRING BOARD – JACK BOARD (SIDE B) –
:Uses unleaded solder.
JACK BOARD (SIDE B)
• Semiconductor
Location
S502
HOLD
ON
OFF
EXCEPT
AEP,EE,UK
=
+
p
^
VOL
11
1-864-411- (11)
D-NE20/NE20LS
20
20
Ref. No.
Location
D902
D904
C-3
D-6
Q303
Q304
Q305
C-7
C-7
D-7
D-NE20/NE20LS
Ver. 1.1
5-9. SCHEMATIC DIAGRAM – JACK BOARD, JACK SUB BOARD, SUB BOARD –
R505 2.2k
R501 10k
R502 4.7k
R503 2.2k
R506 4.7k
S504
S506
R509 1k
CN9002 50P
TP9034
S501
(OPEN/CLOSE)
S503
SL501
R507 10k
R504 22k
CN601 4P
R508 22k
S502
S505
S507
S508
R510
2.2k
S509
S510
TP9005
R511 2.2k
R513
220
IC401
RT8H055C-T1
R514
1k
R512 22k
TP9004
TP9009
R411
1M
TP9007
TP9033
D501
BRPG1211F-TR
C407
470p
TP9032
R314 2.2k
R316
2.2k
CN602 2P
C201 2.2
R202 220
C101 2.2
R102 220
TP9003
TP9001
TP9008
L201
Q304
UMD12N-TR
FB803
R308 1k
R303 2.2k
C301
1
J301
R307 2.2k
Q305
EMG6
C304
1
R304
4.7
TP9036
L101
R311
22k
R312
1M
R313
22k
Q307
EMX18
EXCEPT AEP,EE,UK
C103
0.22
C203
0.22
TP9035
TP9030
TP9038
R315 2.2k
FB804
TP9037
C801
220p
C802
220p
C305
0.1
R203
220k
R103
220k
FB806 0
FB802
FB805
R309 1M
D902
RSB6.8STE61
D901
MAZZ068H01S0
D903
RSB6.8STE61
TP901
C302
0.1
TP9024
C903
1000p
FB801
BLM21B102
16
R305
220k
D904
MA8051-TX
Q301
2SD2652T106
R306
220k
C306
0.01
TP9028
TP9029
Q306
NTHD5904T1
RB301
1.0k
Q302
2SD2652T106
R310
1k
Q303
UMD2N-TR
Q401
2SA1602TP-1EF
TP9026
TP9011
TP9012
D402
MA2YD2300LS0
R401
1M
J401
TP401
TP9014
TP9015
Q402
2SA1363-T111-1E
R402
470k
TP402
TP9013
TP9016
TP403
TP9017
R406 100
CN401
3P
TP9039
R408 47k
TP9019
TP9020
TP407
C402
1
TH401
LF401
TP408
C901
1
C404
4.7
C409 10
R403 470k
D906
RSB6.8STE61
TP410
C403
220 6.3V
Q403
2SD2652T106
D905
MA8051-TX
TP409
W402
J402
F401
1.4A /32V
D401
MA22D2800LS0
W401
R404
220k
R405
47k
TP411
VDR901
FB401
1000P
TP902
FB402
0
R901 0
D-NE20/NE20LS
21
21
R409
220
C406
0.22
R407
0.22
R410
47k
TP9025
D-NE20/NE20LS
• IC Block Diagrams
• IC Pin Function Description
EGH BOARD IC603 CASINO1 (SYSTEM CONTROLLER)
– EGH Board –
Pin No.
IC402 NCP1400ASN22TIG
PE6/SI1
I
Status read signal input from LCD driver (not used)
PE5/SO1
O
Command send signal output to LCD driver (not used)
3
PE4/XSCK1
O
Clock signal output to LCD driver (not used)
4
PE3
O
Chip select signal output to EEPROM
5
VDIO0
–
Power supply terminal (+2.1V)
6
VSS0
–
Ground terminal
POWER
7
DVDD7
–
Power supply terminal (+1.5V)
SWITCH
5
LX
ERROR
AMP
DRIVER
-
8
PE2/DTCK
I
LCD indication of remote control signal output
PHASE
PWM
9
PE1/RxD0
I
not used
COMPENSATION
CONTROLLER
10
PE0/TxD0
O
not used
11
EVA
–
Ground terminal
180 kHz
12
SDDQ16
I/O
Data bus to SDRAM
OSCILLATOR
13
SDDQ15
I/O
Data bus to SDRAM
14
TAPTDO
–
15
SDDQ14
I/O
Data bus to SDRAM
16
SDDQ13
I/O
Data bus to SDRAM
17
SCANEN
–
18
SDDQ12
I/O
Data bus to SDRAM
19
SDDQ11
I/O
Data bus to SDRAM
VOLTAGE
SOFT-START
REFERENCE
NC 3
4
GND
RFOUT
DETIN
CAGCT
CAGCT
CAGCT
IC601 CXD9839K-G
15
14
13
12
11
NC 16
RFIN 17
LOW
BOOST
AGC
RF
EQUALIZER
SERIAL
I/F
RF
EQUALIZER
VDD 18
RF
EQUALIZER
WOBBLE
BPF AMP
2
3
4
5
WBIN
WBOUT
WCIN
WOOUT
WPCOU
20
TEST2
–
21
SDDQ10
I/O
Data bus to SDRAM
22
SDDQ8
I/O
Data bus to SDRAM
23
VDIOSD0
–
–
10 SENB
I/O
Data bus to SDRAM
9
VSS
26
SDDQ6
I/O
Data bus to SDRAM
8
VREF
27
SDDQ7
I/O
Data bus to SDRAM
28
SDDQ2
I/O
Data bus to SDRAM
7
TEST3
–
30
SDDQ4
I/O
Data bus to SDRAM
XPCLK
31
SDDQ3
I/O
Data bus to SDRAM
WPOL
32
TEST0
–
Ground terminal
33
XSDWE
O
WE signal output to SDRAM
34
SDDQ1
I/O
Data bus to SDRAM
35
TEST1
–
36
SDDQ5
I/O
Data bus to SDRAM
37
SDLDQM
O
UDQM signal output to SDRAM
38
VDIOSD1
–
Power supply terminal (+2.1V)
BEEP
Chip select signal output to SDRAM
VDD
XCAS signal output to SDRAM
O
IN2
O
XSDCS
EN2
XSDCAS
42
VSSO
Ground terminal
LDQW signal output to SDRAM
OUT2
–
O
VDDO
VSS2
10
11
12
13
14
41
BPZ
OUTPUT
1
MCK
2
VSS
3
IN1
4
EN1
VSSO
OUT1
VDDO
5
D-NE20/NE20LS
22
22
Ground terminal
SDUDQM
9
OUTPUT
CONTROL
Ground terminal
39
8
6
Ground terminal
29
40
7
Power supply terminal (+2.1V)
VSS1
IC3007 NJU8713V-TE2
BPZ
OUTPUT
Ground terminal
SDDQ9
6
1
Ground terminal
25
WOBBLE
LPF AMP
WLOUT 20
not used
24
to each block
WOIN 19
Description
2
VLX LIMITER
+
I/O
1
CE 1
OUT 2
Pin Name
43
TEST5
–
not used
44
XSDRAS
O
XRAS signal output to SDRAM
45
SDCKE
O
CKE signal output to SDRAM
46
TEST6
–
not used
47
SDCLK
–
Clock signal output to SDRAM
48
SDA13
–
not used
49
XTRST
–
not used
50
SDA12
–
not used
D-NE20/NE20LS
Pin No.
Pin Name
I/O
Description
51
SDA11
O
Address bus to SDRAM
52
SDA10
O
Address bus to SDRAM
53
VDIOSD2
–
Power supply terminal (+2.1V)
54
VSS3
–
Ground terminal
55
DVDD0
–
Power supply terminal (+1.5V)
56
TMS
–
not used
57
SDA8
O
Address bus to SDRAM
58
SDA9
O
Address bus to SDRAM
59
TDO
–
not used
60
SDA7
O
Address bus to SDRAM
61
SDA6
O
Address bus to SDRAM
62
TDI
–
not used
63
SDA4
O
Address bus to SDRAM
64
SDA5
O
Address bus to SDRAM
65
TEST4
–
Ground terminal
66
SDA1
O
Address bus to SDRAM
67
SDA2
O
Address bus to SDRAM
68
RTCK
–
not used
69
SDA0
O
Address bus to SDRAM
70
SDA3
O
Address bus to SDRAM
71
TCK
–
not used
72
VDIOSD3
–
Power supply terminal (+2.1V)
73
VSS4
–
Ground terminal
74
VDIO1
–
Power supply terminal (+2.1V)
75
PI7/AIFBCK
O
Latch signal output to RF amplifier (not used)
76
PI6/AIFLRCK
O
LCD back light on/off signal output (not used)
77
PI5
O
Line out/headphone mute control signal output
78
PI4/AIFPCMD
O
Headphone amplifier chip enable signal output
79
PI3/XBCKO
O
signal output to outside D/A converter (not used)
80
PI2/LRCKO
O
signal output to outside D/A converter (not used)
81
PI1
I/O
not used
82
PI0/PCMDO
O
signal output to outside D/A converter (not used)
83
ADCLK
I
signal output to outside D/A converter (not used)
84
DOUT
O
Output terminal of digital audio signal
85
PJ7/MON7(MONCK)
O
Headphone amplifier setting control signal output
86
PJ6/MON6(MONDO)
O
Headphone amplifier setting control signal output
87
PJ5/MON5
O
Headphone amplifier, power control signal output (not used)
88
PJ4/MON4
O
SCOR monitor signal output (not used)
89
PJ3/MON3
O
GPS monitor signal output (not used)
90
PJ2/MON2
I
Sound pressure regulation volume setting signal output (not used)
91
PJ1/MON1
O
DFCT monitor signal output (not used)
92
XRST_PWR_O
O
not used
93
VSS6
–
Ground terminal
94
VDIO2
–
Power supply terminal (+2.1V)
95
DVDD1
–
Power supply terminal (+1.5V)
96
AVDDA1
–
Power supply terminal (+2.7V)
97
AOUTR
O
Built in D/A converter (R-ch) signal output
98
VREFR
I
Standard voltage terminal (for built in D/A converter R-ch)
99
AVSDA1
–
Ground terminal
23
D-NE20/NE20LS
Pin No.
Pin Name
I/O
100
AVSDA0
–
24
Description
Ground terminal
101
VREFL
I
Standard voltage terminal (for built in D/A converter L-ch)
102
AOUTL
O
Built in D/A converter (L-ch) signal output
103
AVDDA0
–
Power supply terminal (+2.7V)
104
AVSMO
–
Ground terminal
105
EXTAL
O
System clock signal output
106
XTAL
I
System clock signal input
107
AVDMO
–
Power supply terminal (+2.7V)
108
VDIOFS256
–
Power supply terminal (+2.1V)
109
DAMPCLK
O
Master clock signal output to headphone amplifier
110
VDIOAMP
–
Power supply terminal (+2.1V)
111
PWML
O
Audio (L-ch) signal output to headphone amplifier
112
PWMR
O
Audio (R-ch) signal output to headphone amplifier
113
VSSAMP
–
Ground terminal
114
VSS7
–
Ground terminal
115
AVDPLL0
–
Power supply terminal (+2.7V)
116
AVSPLL0
–
Ground terminal
117
VDIOPLL0
–
Power supply terminal (+2.7V)
118
VSS8
–
Ground terminal
119
AVSPLL1
–
Ground terminal
120
AVDPLL1
–
Power supply terminal (+2.7V)
121
VDIOPLL1
–
Power supply terminal (+2.7V)
122
VSS9
–
Ground terminal
123
XIN
–
Ground terminal
124
VDIO3
–
Power supply terminal (+2.1V)
125
MSDIO
I
Pull up fixed at “H”
126
DVDD2
–
Power supply terminal (+1.5V)
127
PF6/DBG6/X_PLUG_DTC
I
Line out plug insert detection signal input
128
PF7/DBG7/X_METAL_DTC
I
Line out plug insert detection signal input
129
ADDR_SEK0
O
not used
130
ADDR_SEK1
O
not used
131
PF3/DBG3
I
not used
132
PF2/DBG2
I
Hold switch input terminal
133
PF1/SSCK/DBG1
O
not used
134
PF0/SSIO/DBG0
O
not used
135
VDIO4
–
Power supply terminal (+2.7V)
136
AVSSAD
–
Ground terminal
137
AVDSAD
–
Power supply terminal (+2.1V)
138
IGEN
I
Pull up fixed at “H”
139
FE(A)
O
RF focus error signal output from pick-up
140
SE(B)
O
RF sled error signal output from pick-up
141
TE(F)
O
RF tracking error signal output from pick-up
142
CE(E)
O
RF select error signal output from pick-up
143
VC
–
Ground terminal
144
RFDC(RFDCO)
I
RF signal input from pick-up
145
VSS11
–
Ground terminal
146
ASYI
I
ASY signal input
147
BIAS
I
Pull up fixed at “H”
148
ASYO
O
ASY signal output
D-NE20/NE20LS
Pin No.
Pin Name
I/O
Description
149
AVDASM
–
Power supply terminal (+2.1V)
150
AVSASM
–
Ground terminal
151
RFACI
I
RF signal output from pick-up
152
AVDVCO
–
Power supply terminal (+2.1V)
153
VCTL
I
VCT signal input
154
CLTV
I
Pull up fixed at “H”
155
AVSVCO
–
Ground terminal
156
VPCO
O
VPC signal output
157
FILO
O
FIL signal output
158
FILI
I
FIL signal input
159
PCO
O
PC signal output
160
VSS12
–
Ground terminal
161
DVDD3
–
Power supply terminal (+1.5V)
162
VDIODSP
–
Power supply terminal (+2.1V)
163
SFDR
O
Sled servo drive PWM signal output to motor driver
164
SRDR
O
Sled servo drive control signal output to motor driver
165
TFDR
O
Tracking servo drive PWM signal output to coil driver (+)
166
TRDR
O
Tracking servo drive PWM signal output to coil driver (-)
167
FFDR
O
Focus servo drive PWM signal output to coil driver (+)
168
FRDR
O
Focus servo drive PWM signal output to coil driver (-)
169
MDP
O
PWM signal output to motor driver
170
MDS
–
not used
171
C176
O
Data signal output to motor driver
172
VDIOEM0
–
Power supply terminal (+2.7V)
173
DVDD4
–
Power supply terminal (+1.5V)
174
VSS14
–
Ground terminal
175
PC3/XSCS0
O
Command latch signal output to power controller
176
PC2/SI0
I
Serial data signal input from EEPROM
177
PC1/SO0
O
Serial data signal output to power controller/EEPROM
178
PC0/XSCK0
O
Clock signal output to power controller/EEPROM
179
VSS15
–
Ground terminal
180
VDIO5
–
Power supply terminal (+2.1V)
181
PG7
I
Reset signal output to power controller
182
PG6
O
LED 1 drive control signal output
183
PG5
O
LED 2 drive control signal output
184
PG4
O
Reset signal output to LCD driver (not used)
185
PG3
O
Switching line/headphone signal output (L = headphone)
186
PG2
O
LED 3 drive control signal output (not used)
187
PG1
O
RF gain control signal output to pick-up
188
PG0
O
Standby control signal output to pick-up
189
DVDD5
–
Power supply terminal (+1.5V)
190
DVDD6
–
Power supply terminal (+1.5V)
191
VSS18
–
Ground terminal
192
AVDAD
–
Power supply terminal (+2.1V)
193
AVSAD
–
Ground terminal
194
AN7
I
Lid upper open/close detection switch input terminal
195
AN6
I
Rest of rechargeable battery detection
196
AN5
I
Battery voltage detection
197
AN4
I
Remote control key signal input
25
D-NE20/NE20LS
Pin No.
Pin Name
I/O
Description
198
AN3
I
Pull up fixed at “H”
199
AN2
I
Key input terminal
200
AN1
I
Key input terminal
201
AN0
I
DC in voltage detection
202
WAKE
I
Wake up control signal input
203
XADEVENT
O
Wake signal output to power controller
204
XRST
I
System reset input terminal
205
DVDBK0
I
Pull up fixed at “H”
206
DVDBK1
I
Pull up fixed at “H”
207
VSS19
–
Ground terminal
208
VDIO6
–
Power supply terminal (+2.1V)
209
PD7/INT7
–
not used
210
PD6/INT6
–
not used
211
PD5/INT5
O
not used
212
PD4/INT4
I
External battery detection signal input (“L”: external battery)
213
PD3/INT3
I
Pull up fixed at “L”
214
PD2/INT2/ECIN
I
FG pulse signal input
215
PD1/INT1/T1
O
not used
216
PD0/INT0/EC0
I
Charging stand detection signal input
217
PE7/ZSCS1
O
LCD driver chip select signal output
218
NCS1
O
Chip enable signal output to P2ROM
219 to 237
A1 to A19
O
Address data signal output to P2ROM
238
NRD
O
Out enable signal output to P2ROM
239
NWE1
–
not used
240 to 255
DQ0 to DQ15
I
P2ROM data signal input
256
VDD_FL1
–
not used
257
VSS_LF1
–
Ground terminal
258
XTAO
–
not used
259
XTAI
–
not used
260
MSBS
–
not used
261
MSSCLK
–
not used
262
NMSINS
–
Power supply terminal (+2.1V)
263 to 272
NC
–
not used
26
D-NE20/NE20LS
Ver. 1.1
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked *“ ” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Color Indication of Appearance Parts Example:
KNOB, BALANCE (WHITE) . . . (RED)
R
R
Parts of Color Cabinet’s Color
6-1.
•
Abbreviation
AUS : Australian model
CH
: Chinese model
CND : Canadian model
E18
: 100-230 V AC area in E model
EA
: Saudi Arabia model
EE
: East European model
HK
: Hong Kong model
JE
: Tourist model
KR
: Korean model
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
OVERALL ASSY
not
supplied
1
not
supplied
not
supplied
not
supplied
not
supplied
3
not
supplied
2
2
4
cabinet (lower ) section
Ref. No.
1
1
1
1
1
Part No.
Description
X-2024-317-1
X-2048-765-1
X-2024-318-1
X-2048-766-1
X-2024-041-1
LID UPPER ASSY (BLUE) (NE20)
LID UPPER ASSY (BLUE) (NE20LS)
LID UPPER ASSY (RED) (NE20)
LID UPPER ASSY (RED) (NE20LS)
LID UPPER ASSY (SILVER) (NE20)
Remark
Ref. No.
1
2
3
4
Part No.
Description
X-2048-764-1
3-234-002-01
2-188-920-01
2-188-921-01
LID UPPER ASSY (SILVER) (NE20LS)
SCREW (UPPER LID)
BLACKET (HINGE L)
BLACKET (HINGE R)
Remark
27
D-NE20/NE20LS
Ver. 1.1
6-2.
CABINET (LOWER) SECTION
51
52
53
66
56
CD mechanism section
(CDM-3325ERV)
57
54
57
57
55
58
not supplied
52
64
63
61
59
65
not
supplied
60
62
Ref. No.
Part No.
Description
51
51
52
53
54
2-541-612-11
2-541-612-21
3-245-709-01
X-2024-309-1
2-187-578-01
LID, BATTERY (EXCEPT CH)
LID, BATTERY (CH)
SCREW
CABI MID SUB ASSY
KNOB, OPEN (L)
55
56
57
58
58
2-187-579-01
3-258-894-01
3-245-331-02
A-1076-645-A
A-1083-356-A
KNOB, OPEN (R)
SPRING (LOCK CLAW)
INSULATOR
EGH BOARD, COMPLETE (JE, HK, KR, CH)
EGH BOARD, COMPLETE (AEP, UK, EE)
58
A-1097-743-A EGH BOARD, COMPLETE
(US, CND, EA, AUS, E18)
2-187-571-01 WINDOW (LED)
2-187-569-01 BUTTON (CONTROL)
2-187-581-01 SPRING (UPPER LID)
X-2024-040-1 CABINET, LOWER SUB ASSY (SILVER)
(US, CND, EA, AUS, JE)
59
60
61
62
62
28
Remark
X-2024-325-1 CABINET, LOWER SUB ASSY (BLUE)
(US, CND, EA, AUS, JE)
Ref. No.
62
62
62
62
62
Part No.
Description
Remark
X-2024-326-1 CABINET, LOWER SUB ASSY (RED)
(US, EA, AUS, JE)
X-2024-514-1 CABINET (LOWER) SUB ASSY (SILVER) (E18)
X-2024-515-1 CABINET (LOWER) SUB ASSY (BLUE) (E18)
X-2024-516-1 CABINET (LOWER) SUB ASSY (RED) (E18)
X-2024-539-1 CABINET (LOWER) SUB ASSY (BLUE)
(AEP, UK, EE)
62
62
62
63
63
X-2048-767-1
X-2048-768-1
X-2048-769-1
A-1076-646-A
A-1098-010-A
CABINET, LOWER SUB ASSY (SILVER) (KR, CH)
CABINET, LOWER SUB ASSY (BLUE) (KR, CH)
CABINET, LOWER SUB ASSY (RED) (KR, CH)
JACK BOARD, COMPLETE (JE, KR)
JACK BOARD, COMPLETE (US, CND)
63
63
64
65
66
A-1098-011-A
A-1113-456-A
2-187-574-01
2-187-575-01
3-254-022-01
JACK BOARD, COMPLETE (E18, EA, AUS, CH)
JACK BOARD, COMPLETE (AEP, EE, UK)
TERMINAL (+), BATTERY
TERMINAL (–), BATTERY
SCREW
D-NE20/NE20LS
6-3.
CD MECHANISM SECTION (CDM-3325ERV)
104
M901
105
106
101
107
102
M902
108
103
109
101
110
111
Ref. No.
Part No.
Description
101
0 102
103
104
105
3-318-203-61
X-3383-995-1
3-221-473-01
3-221-472-02
3-221-474-01
SCREW (B1.7X4), TAPPING
OPTICAL PICK-UP ASSY (DAX-25EV)
COVER, GEAR
CHASSIS
SPRING, SLED
106
107
A-3331-663-A SCREW (FEED) ASSY
3-221-268-01 GEAR (B)
Remark
Ref. No.
Part No.
Description
108
109
110
111
M901
3-221-475-01
3-222-298-01
3-222-299-01
3-348-998-31
A-3174-848-A
SHAFT, STANDARD
RACK
SPRING, RACK RETAINER
SCREW (M1.4X2.5), TAPPING, PAN
MOTOR ASSY, TURN TABLE (SPINDLE)
Remark
M902
A-3174-850-A MOTOR ASSY, SLED (SLED)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
29
D-NE20/NE20LSW-E53
Ver. 1.1
EGH
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
Part No.
•
•
•
•
Abbreviation
AUS : Australian model
CH
: Chinese model
CND : Canadian model
E18
: 100-230 V AC area in E model
EA
: Saudi Arabia model
EE
: East European model
HK
: Hong Kong model
JE
: Tourist model
KR
: Korean model
Accessories are given in the last of this parts
list.
CAPACITORS
uF: µF
COILS
uH: µH
Description
Remark
A-1076-645-A EGH BOARD, COMPLETE (JE,KR,CH)
A-1083-356-A EGH BOARD, COMPLETE (AEP,UK,EE)
A-1097-743-A EGH BOARD, COMPLETE (US,CND,EA,AUS,E18)
**************************************
< CAPACITOR >
C102
C103
C201
C202
C401
1-100-661-11
1-137-859-11
1-125-837-91
1-137-859-11
1-100-506-91
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
100uF
220uF
1uF
220uF
1uF
20%
20%
10%
20%
20%
4V
4V
6.3V
4V
6.3V
C402
C403
C404
C405
C408
1-164-943-11
1-137-710-11
1-100-875-91
1-119-923-11
1-165-887-91
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
100uF
0.047uF
0.22uF
10%
20%
20%
10%
10%
16V
6.3V
6.3V
10V
6.3V
C409
C410
C411
C412
C413
1-164-943-11
1-164-943-11
1-125-777-11
1-125-777-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
0.1uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
10V
10V
16V
C414
C415
C416
C417
C418
1-164-941-11
1-164-943-11
1-127-715-91
1-127-715-91
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.01uF
0.22uF
0.22uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
10V
C419
C420
C421
C422
C423
1-164-943-11
1-125-777-11
1-125-837-91
1-125-837-91
1-100-539-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
0.01uF
0.1uF
1uF
1uF
47uF
10%
10%
10%
10%
20%
16V
10V
6.3V
6.3V
6.3V
C424
C425
C426
C427
C428
1-127-715-91
1-100-506-91
1-100-539-91
1-119-750-11
1-135-259-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
TANTAL. CHIP
0.22uF
1uF
47uF
22uF
10uF
10%
20%
20%
20%
20%
16V
6.3V
6.3V
6.3V
6.3V
C429
C430
C431
C432
C433
1-119-750-11
1-100-539-91
1-100-662-11
1-137-710-11
1-119-923-11
TANTAL. CHIP
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
47uF
47uF
10uF
0.047uF
20%
20%
20%
20%
10%
6.3V
6.3V
6.3V
6.3V
10V
C434
C435
1-125-838-11 CERAMIC CHIP
1-100-507-91 CERAMIC CHIP
2.2uF
4.7uF
10%
20%
6.3V
6.3V
30
Ref. No.
Part No.
•
SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Description
Remark
C436
C437
C438
1-100-415-11 CERAMIC CHIP
1-100-539-91 TANTAL. CHIP
1-100-506-91 CERAMIC CHIP
0.47uF
47uF
1uF
10%
20%
20%
6.3V
6.3V
6.3V
C439
C440
C441
C442
C443
1-165-887-91
1-100-539-91
1-125-777-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
47uF
0.1uF
0.1uF
0.1uF
10%
20%
10%
10%
10%
6.3V
6.3V
10V
10V
10V
C444
C445
C446
C447
C448
1-100-539-91
1-125-777-11
1-125-837-91
1-100-506-91
1-125-777-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.1uF
1uF
1uF
0.1uF
20%
10%
10%
20%
10%
6.3V
10V
6.3V
6.3V
10V
C449
C450
C601
C602
C603
1-164-931-11
1-125-837-91
1-119-750-11
1-112-063-11
1-100-506-91
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
1uF
22uF
470PF
1uF
10%
10%
20%
10%
20%
50V
6.3V
6.3V
50V
6.3V
C604
C605
C606
C607
C608
1-125-777-11
1-127-715-91
1-164-943-11
1-164-943-11
1-164-858-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.22uF
0.01uF
0.01uF
22PF
10%
10%
10%
10%
5%
10V
16V
16V
16V
50V
C609
C610
C611
C612
C613
1-164-939-11
1-100-506-91
1-164-943-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
1uF
0.01uF
0.1uF
0.1uF
10%
20%
10%
10%
10%
50V
6.3V
16V
10V
10V
C614
C617
C618
C619
C626
1-119-923-11
1-164-941-11
1-164-941-11
1-164-941-11
1-100-506-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.0047uF
0.0047uF
0.0047uF
1uF
10%
10%
10%
10%
20%
10V
16V
16V
16V
6.3V
C627
C629
C631
C639
C645
1-119-750-11
1-107-820-11
1-107-820-11
1-107-820-11
1-165-887-91
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.1uF
0.1uF
0.1uF
0.22uF
20%
10%
6.3V
16V
16V
16V
6.3V
C646
C648
C649
C650
C653
1-107-820-11
1-125-777-11
1-100-415-11
1-164-941-11
1-100-415-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.47uF
0.0047uF
0.47uF
10%
10%
10%
10%
16V
10V
6.3V
16V
6.3V
D-NE20/NE20LS
EGH
Ref. No.
Part No.
Description
C654
C659
C664
C667
C676
1-125-777-11
1-107-820-11
1-100-539-91
1-107-820-11
1-107-820-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
47uF
0.1uF
0.1uF
Remark
C677
C678
C680
C681
C686
1-107-820-11
1-119-750-11
1-164-846-11
1-164-846-11
1-100-539-91
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
0.1uF
22uF
6PF
6PF
47uF
C687
C689
1-107-820-11 CERAMIC CHIP
1-107-820-11 CERAMIC CHIP
0.1uF
0.1uF
C694
C695
C3089
1-125-777-11 CERAMIC CHIP 0.1uF
1-100-945-11 CAP, CHIP CERAMIC
1-125-777-11 CERAMIC CHIP 0.1uF
10%
20%
20%
0.5PF
0.5PF
20%
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q406
Q601
Q602
6-551-279-01 TRANSISTOR
8-729-427-49 TRANSISTOR
6-550-232-01 TRANSISTOR
Remark
EMX1T2R
EMT1T2R
QS6K1
QS6K1
DTA115TE
XP4214-TXE
2SA1832FV (TH3SONY)
< RESISTOR >
100
100K
100
100K
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R401
R402
R403
R404
R405
1-218-977-11
1-218-977-11
1-218-977-11
1-218-989-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
100K
100K
1M
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R406
R407
R408
R409
R410
1-216-864-11
1-218-990-11
1-218-977-11
1-218-973-11
1-218-973-11
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
0
100K
47K
47K
5%
5%
5%
1/16W
1/16W
1/16W
R411
R412
R413
R414
R415
1-218-965-11
1-218-957-11
1-218-965-11
1-218-961-11
1-218-941-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
2.2K
10K
4.7K
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R417
R418
R419
R420
R421
1-218-941-81
1-218-969-11
1-218-953-11
1-218-965-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
22K
1K
10K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R423
R424
R426
R427
R428
1-218-961-11
1-218-989-11
1-218-973-11
1-220-804-11
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7K
1M
47K
2.2M
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R429
R430
R431
R432
R435
1-218-969-11
1-218-989-11
1-218-989-11
1-218-953-11
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
22K
1M
1M
1K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R436
R437
R446
R601
R602
1-218-953-11
1-218-953-11
1-218-965-11
1-218-981-11
1-208-911-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
1K
1K
10K
220K
10K
5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R603
R604
1-218-929-11 RES-CHIP
1-218-981-11 RES-CHIP
10
220K
47uH
R606
R607
R608
1-218-990-11 SHORT CHIP
1-218-990-11 SHORT CHIP
1-218-973-11 RES-CHIP
0
0
47K
DTC115TE-TL
R609
R610
R611
1-218-969-11 RES-CHIP
1-218-969-11 RES-CHIP
1-218-990-11 SHORT CHIP
22K
22K
0
6-500-540-01 DIODE RB521S-30FTE61
8-719-071-87 DIODE MA785-(TX), SO
INDUCTOR (EMI FERRITE) (1608)
INDUCTOR (EMI FERRITE) (1608)
FERRITE, EMI (SMD) (1005)
SHORT CHIP
0
< IC >
IC401
IC402
IC403
IC601
IC602
6-706-457-01
6-707-209-01
6-703-652-01
6-707-088-01
6-702-355-01
IC
IC
IC
IC
IC
SC901590VAR2
NCP1400ASN22T1G
LMV301MGX/NOPB
CXD9839K-G
AK6510CL-L
IC603
IC604
IC605
IC606
IC3007
not supplied
6-706-995-01
6-804-719-01
6-707-398-01
6-703-631-01
MOUNTED PC BOARD (CASINO1)
IC MSM56X16160F-20T
IC MR27T1602F (JE, HK, KR, CH)
IC XC6213B212NR
IC NJU8713V-TE2
< COIL >
L401
L402
L403
L404
L405
1-456-894-21
1-400-850-21
1-419-646-21
1-469-967-21
1-400-850-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
47uH
47uH
47uH
10uH
47uH
L406
L407
L408
L409
L410
1-456-218-21
1-400-145-21
1-400-145-21
1-428-912-21
1-400-317-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
22uH
47uH
47uH
10uH
100uH
L412
1-456-894-21 INDUCTOR
< TRANSISTOR >
6-551-139-01 TRANSISTOR
Description
8-729-053-52
8-729-053-54
6-551-140-01
6-551-140-01
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
< FERRITE BEAD >
Q401
Part No.
Q402
Q403
Q404
Q405
1-218-941-81
1-218-977-11
1-218-941-81
1-218-977-11
1-218-941-81
< DIODE >
1-400-808-21
1-400-808-21
1-400-461-21
1-216-864-11
Ref. No.
R101
R102
R201
R202
R302
CN601 1-818-130-11 CONNECTOR, FFC/FPC (ZIF) 15P
CN9001 1-818-842-11 CONNECTOR, BOARD TO BOARD 50P
FB101
FB201
FB401
FB402
16V
6.3V
50V
50V
6.3V
16V
16V
(JE, HK, KR, CH)
10%
10V
4700PF B
10%
10V
< CONNECTOR >
D401
D405
10V
16V
6.3V
16V
16V
5%
1/16W
5%
1/16W
(EXCEPT AEP, UK, EE)
5%
1/16W
5%
5%
1/16W
1/16W
31
D-NE20/NE20LS
Ver. 1.1
EGH JACK
Ref. No.
Part No.
Description
Remark
R612
R613
1-218-977-11 RES-CHIP
1-218-990-11 SHORT CHIP
100K
0
5%
1/16W
R614
R615
R616
R617
R618
1-218-990-11
1-218-981-11
1-218-985-11
1-218-965-11
1-218-953-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
220K
470K
10K
1K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R619
R620
R621
R622
1-400-461-21
1-218-973-11
1-218-953-11
1-218-981-11
FERRITE, EMI (SMD) (1005)
RES-CHIP
47K
5%
RES-CHIP
1K
5%
RES-CHIP
220K
5%
R623
1-208-911-11 METAL CHIP
10K
1/16W
1/16W
1/16W
(AEP, UK, EE)
0.5%
1/16W
R624
R625
R628
R629
R634
1-208-911-11
1-208-911-11
1-218-957-11
1-218-957-11
1-218-965-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
2.2K
2.2K
10K
0.5%
0.5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R635
R636
R637
R639
R642
1-218-989-11
1-218-977-11
1-218-981-11
1-218-973-11
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1M
100K
220K
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R644
R649
R650
R651
R653
1-218-937-11
1-218-969-11
1-218-977-11
1-218-977-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
47
22K
100K
100K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R655
1-218-977-11 RES-CHIP
100K
5%
1/16W
Ref. No.
Part No.
Description
Remark
C407
C409
1-164-935-11 CERAMIC CHIP
1-137-710-11 CERAMIC CHIP
470PF
10uF
10%
20%
50V
6.3V
C801
C802
C901
C903
1-164-933-11
1-164-933-11
1-115-156-11
1-162-964-11
220PF
220PF
1uF
0.001uF
10%
10%
50V
50V
10V
50V
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10%
< CONNECTOR >
CN401
CN601
CN602
CN9002
1-770-620-21
1-785-877-21
1-784-342-21
1-818-843-11
PIN, CONNECTOR 3P
HOUSING, CONNECTOR 4P
HOUSING, CONNECTOR 2P
CONNECTOR, BOARD TO BOARD 50P
< DIODE >
< COMPOSITION CIRCUIT BLOCK >
RB601
1-233-969-11 RES, NETWORK (CHIP TYPE) 22K
< VIBRATOR >
X601
1-813-314-11 VIBRATOR, CRYSTAL 22.579MHz
*************************************************************
A-1076-646-A
A-1098-010-A
A-1098-011-A
A-1113-456-A
JACK BOARD, COMPLETE (JE, KR)
JACK BOARD, COMPLETE (US, CND)
JACK BOARD, COMPLETE (E18, EA, AUS, CH)
JACK BOARD, COMPLETE (AEP, EE, UK)
*************************************
2-187-575-01 TERMINAL (–), BATTERY
D401
D402
D501
D901
D902
6-500-483-01
8-719-085-43
6-500-191-01
8-719-077-43
8-719-083-04
DIODE
DIODE
DIODE
DIODE
DIODE
MA22D2800LS0
MA2YD2300LS0
BRPG1211F-TR (OPR)
MAZZ068H01S0
RSB6.8STE61
D903
D904
D905
D906
8-719-083-04
8-719-422-37
8-719-422-37
8-719-083-04
DIODE
DIODE
DIODE
DIODE
RSB6.8STE61
MA8051-TX
MA8051-TX
RSB6.8STE61
< FUSE >
0 F401
1-576-406-21 FUSE 1.4A/32V
< FERRITE BEAD >
FB401
FB402
FB801
FB802
FB802
1-162-964-11
1-216-864-11
1-414-813-11
1-216-295-91
1-414-813-11
CERAMIC CHIP 0.001uF 10%
50V
SHORT CHIP
0
FERRITE, EMI (SMD) (2012)
SHORT CHIP
0 (US, CND)
FERRITE, EMI (SMD) (2012) (EXCEPT US, CND)
FB803
FB804
FB805
FB806
1-414-813-11
1-414-813-11
1-414-813-11
1-216-295-91
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
SHORT CHIP
0
< IC >
IC401
6-707-315-01 IC RT8H055C-T1
< JACK >
J301
J402
1-818-840-21 JACK (i / LINE OUT(OPTICAL))
1-818-841-11 JACK, DC
< CAPACITOR >
< COIL >
C101
C103
C201
C203
C301
1-165-884-91
1-127-715-91
1-165-884-91
1-127-715-91
1-125-837-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
0.22uF
2.2uF
0.22uF
1uF
10%
10%
10%
10%
10%
6.3V
16V
6.3V
16V
6.3V
C302
C304
C305
C306
C402
1-125-777-11
1-125-837-91
1-125-777-11
1-162-970-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
0.1uF
0.01uF
1uF
10%
10%
10%
10%
10V
6.3V
10V
25V
10V
C403
C404
C406
1-128-829-91 TANTAL. CHIP
1-127-760-11 CERAMIC CHIP
1-127-715-91 CERAMIC CHIP
220uF
4.7uF
0.22uF
20%
10%
10%
32
6.3V
6.3V
16V
L101
L201
1-400-849-21 INDUCTOR, CHIP 100uH (2518)
1-400-849-21 INDUCTOR, CHIP 100uH (2518)
< LINE FILTER >
LF401
1-416-405-21 FILTER, CHIP EMI (COMMON MODE)
< TRANSISTOR >
Q301
Q302
Q303
6-550-364-01 TRANSISTOR
6-550-364-01 TRANSISTOR
6-550-375-01 TRANSISTOR
2SD2652T106
2SD2652T106
UMD2N-TR
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
D-NE20/NE20LS
JACK
Ref. No.
Part No.
Description
Remark
Q304
Q305
8-729-047-48 TRANSISTOR
6-551-132-01 TRANSISTOR
UMD12N-TR
EMG6 (EXCEPT AEP, EE, UK)
Q306
Q307
Q401
Q402
Q403
6-550-527-01
6-551-186-01
8-729-602-36
6-550-760-01
6-550-364-01
NTHD5904T1
EMX18
2SA1602TP-1EF
2SA1363-T111-1E
2SD2652T106
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Ref. No.
Part No.
JACK SUB
Description
Ver. 1.1
SUB
Remark
< SWITCH >
< RESISTOR >
S501
S502
S503
S504
S505
1-762-805-41
1-572-922-11
1-771-105-11
1-771-105-11
1-771-105-11
SWITCH, PUSH (1 KEY)
SWITCH, SLIDE (HOLD .)
SWITCH, TACTILE (–(
))
SWITCH, TACTILE (+(
))
SWITCH, TACTILE (–(VOL))
S506
S507
S508
S509
S510
1-771-105-11
1-771-105-11
1-771-105-11
1-771-105-11
1-771-105-11
SWITCH, TACTILE (.)
SWITCH, TACTILE (+(VOL))
SWITCH, TACTILE (>)
SWITCH, TACTILE (x)
SWITCH, TACTILE (u)
R102
R103
R202
R203
R303
1-218-945-11
1-218-981-11
1-218-945-11
1-218-981-11
1-218-957-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
220
220K
220
220K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R304
R305
R306
R307
R308
1-220-803-81
1-218-981-11
1-218-981-11
1-218-957-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7
220K
220K
2.2K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R309
R310
R311
R312
R313
1-218-989-11
1-218-953-11
1-218-969-11
1-218-989-11
1-218-969-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1M
1K
22K
1M
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R314
R315
R316
1-218-957-11 RES-CHIP
1-218-957-11 RES-CHIP
1-216-825-11 METAL CHIP
R401
R402
1-218-989-11 RES-CHIP
1-218-985-11 RES-CHIP
5%
1/16W
5%
1/16W
5%
1/10W
(EXCEPT AEP, EE, UK)
1M
5%
1/16W
470K
5%
1/16W
R403
R404
R405
R406
R407
1-218-985-11
1-208-943-11
1-208-927-11
1-218-941-81
1-245-927-21
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
470K
220K
47K
100
0.22
5%
0.5%
0.5%
5%
1%
1/16W
1/16W
1/16W
1/16W
1/5W
R408
R409
R410
R411
R501
1-218-973-11
1-218-945-11
1-218-973-11
1-218-989-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
47K
220
47K
1M
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R502
R503
R504
R505
R506
1-218-961-11
1-218-957-11
1-218-969-11
1-218-957-11
1-218-961-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7K
2.2K
22K
2.2K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
0
0
0
0
0
1-478-845-21
1-478-846-21
1-478-847-21
1-478-848-21
1-478-849-21
ADAPTOR, AC (AC-ES3010K2) (CH)
ADAPTOR, AC (AC-ES3010K2) (US, CND)
ADAPTOR, AC (AC-ES3010K2) (KR)
ADAPTOR, AC (AC-ES3010K2) (AEP, EE, E18)
ADAPTOR, AC (AC-ES3010K2) (UK, EA, HK)
R507
R508
R509
R510
R511
1-218-965-11
1-218-969-11
1-218-953-11
1-218-957-11
1-218-957-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
22K
1K
2.2K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
0
0
0
1-478-850-21
1-478-853-22
1-569-007-22
1-756-120-51
1-756-120-61
1-816-149-32
ADAPTOR, AC (AC-ES3010K2) (AUS)
ADAPTOR, AC (AC-ES3010K2) (JE)
ADAPTOR, CONVERSION 2P (JE)
BATTERY, NICKEL HYDROGEN (EXCEPT US)
BATTERY, NICKEL HYDROGEN (US, CND)
PLUG, DC
R512
R513
R514
R901
1-218-969-11
1-218-945-11
1-218-953-11
1-216-864-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
22K
220
1K
0
5%
5%
5%
1/16W
1/16W
1/16W
< THERMISTOR >
TH401
2.2K
2.2K
2.2K
< COMPOSITION CIRCUIT BLOCK >
RB301
1-233-787-11 RES, NETWORK
1.0K (1608)
1-805-719-11 THERMISTOR, POSITIVE
< VARISTOR >
VDR901 1-801-862-11 VARISTOR, CHIP
(1608)
*************************************************************
JACK SUB BOARD
***************
< JACK >
J401
1-818-841-11 JACK, DC
*************************************************************
SUB BOARD
**********
2-187-574-01 TERMINAL (+), BATTERY
*************************************************************
MISCELLANEOUS
**************
0 102
M901
M902
X-3383-995-1 OPTICAL PICK-UP ASSY (DAX-25EV)
A-3174-848-A MOTOR ASSY, TURN TABLE (SPINDLE)
A-3174-850-A MOTOR ASSY, SLED (SLED)
ACCESSORIES
************
2-187-958-01 COVER, BATTERY CASE
2-318-320-11 MANUAL, INSTRUCTION (ENGLISH)
(EXCEPT EA, KR)
2-318-320-21 MANUAL, INSTRUCTION
(SPANISH, PORTUGUESE, FRENCH) (CND, AEP)
2-318-320-31 MANUAL, INSTRUCTION
(DUTCH, GERMAN, ITALISH) (AEP)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
33
D-NE20/NE20LS
Ver. 1.1
Ref. No.
Part No.
Description
Remark
2-318-320-41 MANUAL, INSTRUCTION
(SWEDISH, FINNISH) (AEP)
2-318-320-51 MANUAL, INSTRUCTION
(HUNGARIAN, RUSSIAN, POLISH) (EE)
2-318-320-61 MANUAL, INSTRUCTION
(CZECH, SLOVAK) (EE)
2-318-320-71 MANUAL, INSTRUCTION (KOREAN) (JE, KR)
2-318-320-81 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (JE, HK)
2-318-320-91 MANUAL, INSTRUCTION
(SIMPLIFIED CHINESE) (E18, JE, CH)
2-318-321-11
2-318-321-21
2-318-452-11
2-345-232-11
MANUAL, INSTRUCTION (ENGLISH) (EA)
MANUAL, INSTRUCTION (ARABIC) (EA)
MANUAL, INSTRUCTION (EE)
MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(ENGLISH) (JE, E18, EA, AUS, CH)
2-345-232-21 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE) (SPANISH) (AEP)
2-345-232-31 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(PORTUGUESE) (AEP)
2-345-232-41 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE) (FRENCH) (AEP)
2-345-232-51 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(DUTCH, GERMAN, ITALISH) (AEP)
2-345-232-61 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(SWEDISH, FINNISH) (AEP)
2-345-232-71 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(HUNGARIAN, RUSSIAN, POLISH) (EE)
2-345-232-81 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(CZECH, SLOVAK) (EE)
2-345-232-91 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE) (ARABIC) (EA)
2-348-135-11 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(KOREAN) (JE, KR)
2-348-135-21 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(TRADITIONAL CHINESE) (JE, HK)
2-348-135-31 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(SIMPLIFIED CHINESE) (E18, JE, CH)
2-590-336-11 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(ENGLISH) (US, CND, AEP, UK, EE)
2-590-336-21 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE) (SPANISH) (AEP)
2-590-336-31 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(PORTUGUESE) (AEP)
2-590-336-41 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(FRENCH) (CND, AEP)
2-590-336-51 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(DUTCH, GERMAN, ITALISH) (AEP)
34
Ref. No.
Part No.
Description
Remark
2-590-336-61 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(SWEDISH, FINNISH) (AEP)
2-590-336-71 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(HUNGARIAN, RUSSIAN, POLISH) (EE)
2-590-336-81 MANUAL, INSTRUCTION
(INSTALL OPERATION GUIDE)
(CZECH, SLOVAK) (EE)
3-008-521-01
3-021-018-01
3-235-292-02
8-912-735-90
CASE, CHARGE
LABEL, FRANCE (AEP)
POUCH, CARRYING
HEADPHONE MDR-E0931SP/B SET
(EA, AUS, E18, JE, HK, KR, CH)
8-912-742-91 EARPHONES MDR-E0931SPB9 SET
(US, CND, AEP, UK, EE)
A-1071-445-A RM-MC55ELK/SM (JE, HK, KR, CH)
A-1071-446-A RM-MC53EL/SM
(US, CND, AEP, UK, EE, EA, AUS, E18)
A-1074-427-A EBP-J101//M (EXTERNAL BATTERY CASE)
A-1077-817-A BCA-DNE20/SM
(CHARGING STAND) (FOR SILVER)
A-1078-511-A BCA-DNE20/BM
(CHARGING STAND) (FOR BLUE, RED)
X-2024-504-2 CD-ROM (APPLICATION) ASSY
(SS2.1)(SonicStage)(CH)
X-2024-753-1 (APPLICATION) ASSY
(SS2.1)(SonicStage)(JE, E18, EA, KR, AUS)
X-2050-857-1 CD-ROM (APPLICATION) ASSY
(SS2.3)(SonicStage)(US, CND, AEP, UK, EE)
D-NE20/NE20LS
MEMO
35
D-NE20/NE20LS
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.0
2004.11
New
1.1
2005.01
Addition of Canadian model for D-NE20
Change a color variation into blue for UK and EE model

Similar documents

D-NE920/NE920LS

D-NE920/NE920LS • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be no...

More information

R91 - Minidisc.org

R91 - Minidisc.org 6-6. IC Pin Function Description ...........................................

More information

NF520 - Minidisc.org

NF520 - Minidisc.org other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tant...

More information

SRF-MQ11

SRF-MQ11 Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be a...

More information