service catalog

SERVICE CATALOG
Service & Parts Department Phone: 614-548-0098
MADE IN THE USA
The information included in the Staber Service Catalog may change without notice.
Please see our website for updates, corrections, or additions.
Part # 818905
Staber Industries has used all possible care to assure that the information contained in our
service catalog is as complete and accurate as possible. However, Staber Industries
assumes no liability for omissions, errors or defects in the materials, instructions or
diagrams contained in this publication. Therefore, Staber Industries is not liable for any
damages including (but not limited to) personal injury, property damage or legal disputes
that may result from the use of our publication.
Personal injury or property damage may occur before, during, or after any attempt to
repair an appliance. Our service catalog was intended for use by individuals possessing
an adequate background of technical experience. Staber Industries is not responsible for
an individual’s judgment of his or her own technical abilities and experience, and
therefore are not liable for any damages including (but not limited to) personal injury,
property damage or legal disputes that may result from such judgments. Staber Industries
is not responsible for interpretation or implementation of the items contained in this
publication.
Use of our service catalog acknowledges the understanding and acceptance of above said
terms and conditions.
All rights reserved. No portion of our service catalog may be copied or reprinted without
express written permission of Staber Industries, except for brief passages which may be
quoted with the proper credit line. Write to the address below for permission of
duplication of material.
Published by:
Staber Industries, Inc.
4800 Homer Ohio Lane
Groveport OH 43125
614-548-0098
www.staber.com
REMOVAL OF FRONT PANEL
1. Disconnect the appliance from the power source.
2. Remove the four 5/16 headed screws located at the bottom of the
front panel
3. After the screws have been removed, grasp the panel on both sides
and pull forward. Allow the panel to drop free of the top assembly
and set aside.
INSTALLATION OF FRONT PANEL
1. Locate left and right side of front panel over pin guides on cabinet.
2. While applying upward pressure, use a 5/16 nut driver and screw the
four 5/16 headed screws back in the bottom of the panel.
PROBLEM:
WASHER LEAKING
DURING WASH CYCLE
WHEN DOES
IT LEAK?
CHECK HOSE
CONNECTIONS, CLAMPS,
SOAP DISPENSER, OR BEZEL
YES
IS IT ONLY
LEAKING
DURING THE
FILL?
NO
DOES THE TUB
START AND
STOP EVERY 13
SECONDS ON
‘NORMAL’?
NO
CHECK/REPLACE CIRCUIT
BOARD
YES
DURING SPIN CYCLE
CHECK SOAP SUDS
LEVEL LOOKING
INTO INNER TUB
AFTER 5 MINUTES
OF WASHING. TOO
MUCH SOAP SUDS?
YES
REDUCE SOAP AMOUNT
NO
CHECK AGAIN FOR
LEAKAGE FROM SOAP
DISPENSER AREA
IS THE SUMP
HOSE SAGGING?
DOES IT NEED A
SUMP HOSE
HANGER? CHECK
DATE OF
MACHINE.
DOES MACHINE
RAMP UP &
SPIN
CORRECTLY?
NO
YES
TOO MUCH
SOAP SUDS?
YES
REDUCE SOAP
AMOUNT/USE
FABRIC
SOFTENER
NO
NO
IS THE
SKIRT
AREA
LEAKING?
YES
CHECK/REPLACE
CIRCUIT BOARD
SEND SUMP
HOSE
HANGER
YES
REPLACE
SKIRT KIT
NO
MAKE SURE
THERE IS A WIRE
TIE
MAKE SURE THE
SUMP HOSE
SEALANT IS NOT
LEAKING
MAKE SURE
THERE IS NOT A
HOLE IN THE
DRAIN HOSE
NO
IS THE TUB
BEZEL
LEAKING?
YES
REPLACE THE
TUB BEZEL
PROBLEM:
WASHER WON’T AGITATE
DOES
MACHINE
AGITATE?
NO
CHECK BRUSHES ON MOTOR
YES
NO
CHECK WIRE 1 &
WIRE 2 ON
PROGRAM
SELECTOR
SWITCH: IS IT
DISCONNECTED?
YES
NO
IS OUT OF
BALANCE
SWITCH
CLOSED?
RECONNECT & RETEST
MACHINE
REPLACE CIRCUIT BOARD
NO
REPLACE CIRCUIT BOARD
NO
REPLACE OUT OF BALANCE
SWITCH
YES
NO
YES
CHECK LED
Y120: IS IT
LIT?
YES
REPLACE CIRCUIT BOARD
YES
CHECK
LED
Y110: IS
IT LIT?
RECONNECT & RETEST
MACHINE
NO
CHECK LED
Y121: IS IT
LIT?
YES
NO
CHECK LED
Y101 ON
CIRCUIT
BOARD: IS IT
LIT?
CHECK FOR WIRE
1A: IS IT
DISCONNECTED
FROM PROGRAM
SELECTOR SWITCH?
CHECK
PRESSURE
SWITCH FOR
CONTINUITY ON
11 & 12. DO YOU
HAVE
CONTINUITY?
YE
S
NO
CHECK LID LOCK AGAIN
REPLACE PRESSURE SWITCH
PROBLEM:
WASHER WON’T SPIN/AGITATE
PUSH IN
GENTLY
YES
IS CIRCUIT
BREAKER
POPPED OUT
ON BACK OF
MACHINE?
NO
IS THE
POWER
LIGHT ON?
NO
CHECK MAIN
HOUSE
BREAKER
IS THERE
VOLTAGE
TO THE
OUTLET?
YES
YES
PUSH DOWN
ON LID. IS THE
LID LOCK
LIGHT ON
NOW?
NO
IF PROBLEM PERSISTS,
REPLACE LID LOCK &
AFTER REPLACEMENT
RETEST MACHINE
MACHINE SHOULD
NOW SPIN
YES
IS THE LID
LOCK LIGHT
ON?
THAT IS THE
PROBLEM. CALL
ELECTRICIAN.
NO
CHECK LID LOCK
PIN TO SEE IF
BROKEN.
NO
CHECK FOR BUSTED
WIRE ON LID LOCK
CONNECTOR
THIS IS
PROBLEM: FIX
POWER SOURCE
YES
IS THERE
WATER
STANDING IN
THE TUB?
NO
YES
CLOGGED
PUMP?
YES
IS THERE
VOLTAGE
TO THE
PUMP?
IS THE
BELT
OFF?
CHECK/REPLACE
PULLEY
CLEAR OBSTRUCTION
NO
IS THE
BELT
BROKEN?
YES
REPLACE BELT/MAKE
SURE TUB SPINS FREELY
NO
DOES
MACHINE
AGITATE?
YES
NO
CHECK FOR STUCK BRUSHES
ON MOTOR (SEE
INSTRUCTION SHEET)
NO
YES
NO
REPLACE PUMP
NO
YES
YES
CHECK
FREQUENCY
TO PUMP: DO
YOU HAVE 60
HZ.?
REPLACE TIMER
CHECK LED’S ON
CIRCUIT BOARD; MAKE
SURE WE HAVE 4
LIGHTS. IF NOT, WHICH
LIGHT IS NOT ON?
CHECK LED Y101 ON
CIRCUIT BOARD: IS IT
LIT?
NO
CHECK FOR WIRE
1A: IS IT
DISCONNECTED
FROM PROGRAM
SELECTOR SWITCH?
YES
RECONNECT & RETEST
MACHINE
NO
YES
NO
CHECK LED
Y121: IS IT
LIT?
REPLACE CIRCUIT BOARD
CHECK WIRE 1 &
WIRE 2 ON
PROGRAM
SELECTOR
SWITCH: IS IT
DISCONNECTED?
YES
RECONNECT & RETEST
MACHINE
NO
YES
CHECK
LED
Y110: IS
IT LIT?
NO
REPLACE CIRCUIT BOARD
YES
CHECK LED
Y120: IS IT
LIT?
IS OUT OF
BALANCE
SWITCH
CLOSED?
REPLACE OUT OF BALANCE
SWITCH
NO
YES
NO
REPLACE CIRCUIT BOARD
CHECK
PRESSURE
SWITCH FOR
CONTINUITY ON
11 & 12. DO YOU
HAVE
CONTINUITY?
YES
CHECK LID LOCK AGAIN
NO
REPLACE PRESSURE SWITCH
STABER
INDUSTRIES, INC.
www.staber.com
4800 Homer Ohio Lane • Groveport, OH 43125 • Service Dept. Phone 614-548-0098 • FAX 614-836-9524
Bearing Replacement Procedure
Parts Needed
Qty.
1
2
1
1
3
8
2
2
8
1
Part #
819903
817105
817107
817109
811203
818201
817351
811217
818377
818407
Tools Needed
Description
Instruction Sheet
Assembly, bearing
Assembly, drive shaft
Assembly, support shaft
Hub gasket
Bolt ¼ x 20 x 5/8 SS HH
Flange cover
O-Rings
Flange cover washer
Grease
7/16 Ratchet and socket
5/32 Allen wrench
Screwdriver
File
Instructions:
Remove front panel
2. Raise top and prop up
3. Remove bezel; read next line for instructions
4. Unhook spring from back side of bezel
5. Take a flat head screwdriver and gently pry in
between the bezel and the outer tub (we are making
sure not to shear off the plastic tabs on the bezel).
Gently pry the four corners first and then continue
going around the bezel so that the tabs release. Pull
bezel out paying close attention on how it was seated
(see illus. 1).
Illustration 1
6. Remove drive pulley by loosening set screws
7. File off burrs (if any) on drive shaft (see illus. 2)
8. Remove four bolts holding shaft to inner tub (drive and support shaft); (see illus. 3)
1.
Illustration 3
Illustration 2
Part # 819903 R6
Publish Date: Aug. 2, 2005
9. Pull shafts to the center of inner tub (see illus. 4)
Illustration 4
Illustration 5
10. Lift inner tub out of outer tub
11. Remove six bolts holding bearing assembly to outer tub (see illus. 5)
Illustration 6
Illustration 7
12. Remove the two gaskets on front bearing housing, and the one gasket on the rear bearing housing (see illus. 6)
13. Remove Magnetic switch from old bearing assembly.
14. Install Magnetic switch on new front bearing assembly.
15. Add new grease to seal area of new bearing assembly and to the shaft
16. Install O-Rings on new shafts; slide up to step on shaft
17. Reinstall the bearing assemblies by reversing the above process (see illus. 5, 6 & 7)
18. Insert inner tub into outer tub. Note: the door with the ‘Press Here’ tab should be on the left.
19. Install rear tub support shaft.
20. Install rear bolt, lock washer, fender washer and tighten.
21. Install the rear flange cover putting the stainless steel flat washers between the head of the bolt & flange cover.
22. Install front tub drive shaft with the flat portion facing straight down toward the motor.
23. Align the drive pulley’s magnet with the bearing assembly’s magnetic switch.
24. Install the spacer and then the pulley on the drive shaft.
25. Install safety bolt, lock washer and fender washer on drive shaft.
26. Tighten the pulley’s set screws on shaft.
27. Install the safety wire into the pulley’s predrilled hole and the safety bolt twisting the ends together.
28. Install front flange cover putting the stainless flat washers between the head of the bolt and the flange cover.
29. Before you reinstall the bezel, straighten the four corner edges of the outer tub with a pair of pliers or Channel
Locks where you had removed the bezel.
30. Reinstall the bezel into the outer tub; you can use a rubber mallet to help get the tabs into place.
31. To keep the bezel tight, you can crimp the sides with a pair of Channel Locks.
32. Grease the bearing assembly every three years with no more than one ounce of Lubriplate #1200-2
Part # 819903 R6
Publish Date: Aug. 2, 2005
STABER
INDUSTRIES, INC.
www.staber.com
4800 Homer Ohio Lane • Groveport, OH 43125 • Service Dept. Phone 614-548-0098 • FAX 614-836-9524
Procedure for Replacing Control Board (Part # 813224 or 813226)
This is a brief procedure for servicing the motor control board. Depending on your serial number, the
new control board may appear different than the board you are replacing.
A. First unplug the machine from its power source.
B. Remove the four screws located at the bottom of the front panel. This will require a 5/16-nut driver
or a socket. Note: Notice the position of the front panel in regards to the top panel. This position
will be important when replacing the front panel.
C. With all four screws removed, pull out and down on the front panel. There are two locating pins on
each side of the front of the cabinet; you will need to clear these pins. The panel should now be
clear of the machine. Set this panel to the side.
D. Remove the two 5/16-headed screws located at the upper left and right corner of the edge of the
cabinet. These two screws will allow access to the interior of the machine. Set these two screws
aside separate from the other four screws because they may be different on your machine.
E. Lift up on the front of the top until the two front clips have cleared the edge of the cabinet. Note:
Secure the lid to the top panel with a piece of tape or some other means. Once the top is raised
vertically, the lid might open and fall backwards. This could damage the lid or cause it to become
detached from the top.
F. Pull the plastic top assembly towards you an inch to free up the hinges on the back. Then lift the
top until you can gain access to the rear wall of the cabinet. Note: Again, secure the top so it will
remain open while you are working in this area. If the top is not secured, it could fall closed while
you are working in this area.
G. The motor control board is now accessible. The location of the board is on the rear upper right
corner of the cabinet.
H. Removal of the control board (for models HXW2300, HXW2301, HXW2302, HXW2303, and
HXW2304 to Aug. ‘01 control board replacement)
1. Remove both of the wire connections on top of the control board. Note: It is advisable to
secure the board with your free hand while removing the wire connections.
2. The right-hand connector will pull off. It may require a little force to pull the connector
free. Again, secure the board with your free hand while removing this connector.
3. The left-hand connector has two retaining clips on either side of the connector. While
squeezing these two connectors, rock the connector back and forth until the connector is
free.
4. Disconnect the two wires on the circuit board that connect to the circuit breaker. These will
no longer be needed with the new control board.
5. To release the board from the four standoffs, there is a latching pin in the center of the
standoff that sticks through the board. Depress this latch while gently pulling out on the
corner of the board. Repeat this procedure until all four corners are free. Now the board can
be removed from the machine.
6. Remove all four plastic standoffs.
I. Removal of the control board (For model HXW2304 after Aug. ’01)
1. Remove right-hand wire connector as indicated in H-2 above
J.
K.
L.
M.
2. Remove left-hand wire harness connector as indicated in H-3 above
3. Remove three plastic thumb screws from the three corners of the aluminum plate
4. Remove three plastic standoffs from stud
5. Remove control board from mounting studs
To replace the board, perform this procedure in reverse.
1. (For model HXW2300, HXW2301, HXW2302, HXW2303, and HXW2304 prior to Aug.
’01) Slide the control board’s studs into the standoff holes in the back of the machine.
2. (For HXW2304 after Aug. ’01) Put control board on mounting studs; install standoffs and
thumbnuts.
Note: The left-hand connection can go on only one way. There is a flat side on one
of the connections that only allows the connector to be inserted one way. Also, the
right-hand connector (called J2) will go on with the silver terminals facing up (*see
photo below).
Lower the top back into position and re-set the two hinges into place on the back.
1. While lowering the top, ensure that the rubber skirt is located in the gray bezel. The bezel is
the plastic insert that covers the spinner basket. There is a channel around the bezel that
locates the skirt. This is the section that has the hump on the bezel. Ensure that all four sides
of the skirt are located in this area or there is great risk of water escaping during wash and
spin.
2. Ensure that the two top clips are located behind the edge of the cabinet in the front. Replace
and tighten two of the 5/16 headed screws.
Replace the front panel and tighten the four 5/16 headed screws.
1. Ensure that the top of the front panel is properly located or the panel will rattle during spin.
This panel also gives the machine its stability and if it is not located properly damage may
be incurred.
2. Guide the front panel over the two location pins.
3. Align the holes at the bottom of the front panel and tighten the four 5/16 headed screws.
Remove the restraint that is securing the lid and open. Rotate the basket until the doors are facing
down. With some force, press down on the basket with both hands. Visually inspect to see that the
rubber skirt is positioned in the bezel.
Note: Please return defective board within two weeks. (Return via regular mail, no insurance or
Priority Mail required, using box it was shipped in and label provided.)
J1-1 wire
(this wire
is on the
left side)
*Silver
terminals are
facing up
J2-12 wire
(this wire
must be on
the right
side)
STABER
INDUSTRIES, INC.
www.staber.com
4800 Homer Ohio Lane • Groveport, OH 43125 • Service Dept. Phone 614-548-0098 • FAX 614-836-9524
REPLACING A MECHANICAL TIMER
1. Unplug machine.
2. Using a Philips screwdriver, remove the six screws on the control panel.
3. Push timer knob in, gently pull control panel forward, and pull black pin on back
of timer out about a half an inch (see Figure 1).
Figure 1
4. After pulling the black pin out, this will allow you to remove the large knob, disk,
and small spacer off the front of control panel.
5. Remove the plastic wire tie around the wire harness connected to the timer (see
Figure 2).
Figure 2
6. Lift up gently on plastic tab to remove wire harness plug (see Figure 3).
Figure 3
7. Remove screw (see Figure 4), lift tab, then slide timer to the left to remove.
Figure 4
8. Reverse procedure to install new timer. When it is time to put the knob on, put the
knob on while making sure the black pin on the back of the timer is pushed in all
the way until you hear it ‘click’ into place. This will keep you from being able to
pull the knob off.
STABER
INDUSTRIES, INC.
www.staber.com
4800 Homer Ohio Lane • Groveport, OH 43125 • Service Dept. Phone 614-548-0098 • FAX 614-836-9524
CHECKING FOR STUCK BRUSHES & CONTINUITY ON A
MOTOR
1. Disconnect the washer from the power source.
2. Remove the four 5/16 headed screws located at the bottom of the front panel.
3. After the screws have been removed, grasp the panel on both sides and pull forward. Allow
the panel to drop free of the top assembly and set aside.
4. You will need a pencil, pen, or small screw driver.
5. The motor is under the tub.
6. On the right side of the motor about 7/8th’s of the way back there is a square hole that is a
little larger than a pencil. On the back side of this hole there is a piece of rubbery siliconetype material. Do not push on this piece of silicone; we are using it as a guide only. Put the
screwdriver in front of the piece of silicone and insert it into the motor approximately ½
inch. You should hit something hard. If you go in more than ½ inch you are not in the
correct spot. When you hit something hard give it a nudge, you will not feel it move. Now,
while applying pressure on this same spot manually turn the drum with the pulley 2-3
revolutions and you should hear a ‘friction buzzing’ sound and feel some bumps.
7. Go to the left side of the motor. This is the same hole, same spot, same situation, but the
hole is behind the flange that is part of the motor housing that comes out over the wire
harness. Do the same thing: Put the screwdriver in front of the piece of silicone and insert
it into the motor approximately ½ inch. You should hit something hard. If you go in more
than ½ inch you are not in the correct spot. When you hit something hard give it a nudge,
you will not feel it move. Now, while applying pressure on this same spot manually turn
the drum with the pulley 2-3 revolutions and you should hear a ‘friction buzzing’ sound and
feel some bumps.
8. Plug machine back in and turn the timer knob straight down to the floor just beyond the
spin and the motor should start to turn.
This is a view of the left side of the
motor towards the back looking at
the hole where you need to push in
on the brush.
This is a view of the right side of
the motor towards the back looking
at the hole where you need to push
in on the brush.
(CONTINUED ON BACK)
9. If the machine does not start, then you would need to check for continuity on the motor.
You will need a multi-meter (or volt-meter), and put it on ‘OHMS’.
10. Disconnect the washer from the power source.
11. Unplug the wiring harness from the motor.
12. There are eight pins on the motor. Counting from the top down you would need to check for
continuity (the needle should move as opposed to staying still) between pins 1-2, 1-3, 2-3,
4-5, and 6-7. Pins 4-5 are the brushes. If you do not have continuity between any of these
pins, then the motor would need to be replaced. If you have continuity between all pins,
then the motor is good.
This is a front view of the motor. The motor is located
at the front bottom of the outer tub.
The hole for the brush is
behind this flange that
the wire harness is
connected to on the left
side of the motor.
The hole for the brush is
located at the right side
of the motor towards the
back.
STABER
INDUSTRIES, INC.
www.staber.com
4800 Homer Ohio Lane • Groveport, OH 43125 • Service Dept. Phone 614-548-0098 • FAX 614-836-9524
REPLACING A MOTOR
1. Disconnect the washer from the power source.
2. Remove the four 5/16 headed screws located at the bottom of the front panel.
3. After the screws have been removed, grasp the panel on both sides and pull forward. Allow
the panel to drop free of the top assembly and set aside.
4. Note position of wiring plug on the motor and remove plug from motor.
5. Remove the belt adjustment bolt and drive belt from motor.
6. Remove clip and washer from pivot shaft. Slide shaft to rear far enough to allow motor to
come off shaft.
7. Remove all rubber leg grommets from old motor and install on replacement motor.
8. Position replacement motor on shaft, slide shaft into position and secure with washer and
clip. Install drive belt adjustment bolt on motor. Install drive belt, adjust belt tension so that
there is approximately 1/4-1/2 ” deflection on either side of the belt midway between the
two pulleys (or 65-70 foot/lbs.) and tighten adjustment bolt.
9. Install wiring plug on new motor as noted above.
10. Plug power cord into electrical receptacle. Test installation by momentarily pulling out on
the timer knob and verifying that the inner tub rotates.
11. Install front panel on clothes washer by locating left and right side of front panel over the
guide pins on the cabinet.
12. While applying upward pressure, screw the four 5/16 headed screws back into the bottom
of the front panel.
STABER
INDUSTRIES, INC.
www.staber.com
4800 Homer Ohio Lane • Groveport, OH 43125 • Service Dept. Phone 614-548-0098 • FAX 614-836-9524
Pulley Replacement Procedure
Parts Needed
Qty.
1
1
1
1
1
Tools Needed
Part #
817135
818349
818285
818293
818361
Description
Pulley Assembly
½ x ¼ x 20 Safety Bolt
¼ Lock washer
¼ Flat washer
9”x.029d safety wire
-5/16” wrench, closed end or 5/32” allen wrench
-7/16” wrench, closed end or ratchet and socket
-Metal file, small and fine preferred
-One sheet of wet/dry type (black) sandpaper (600 grit)
or fine emery cloth
-Socket and ¼” or 3/8” drive ratchet, & 5/16”, 7/16”
sockets (only a 5/16” socket with eight or more internal
sides will work on set bolts, otherwise use the 5/16”
wrench)
-Several clean rags
-White lithium grease (if desired)
-Bolt thread locking liquid or ‘glue’ (available at auto
parts stores & hardware stores)
-Vise grips
-Side cutters
Instructions:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Disconnect the washer from the power source.
Remove the four 5/16 headed screws located at the bottom of the front panel.
After the screws have been removed, grasp the panel on both sides and pull forward. Allow
the panel to drop free of the top assembly and set aside.
Remove safety wire (Part No. 818361) from old pulley.
Remove front bolt and washer (Part No.’s 42, 41)
Back-out set-screws or set-bolts on old pulley by unscrewing with a 5/32”allen wrench or
5/16” closed-end wrench.
Grasp opposite sides and pull the old pulley toward you until off. Wiggle pulley while
pulling may be necessary.
Clean shaft with a rag.
File down ridges with a small fine file where set-screw was until shaft is smooth
Clean and polish with a strip from a sheet of fine emery cloth or wet-dry sand paper (600
grit)
Inspect the new pulley making sure the set-bolts are backed-out and recessed in the pulley
body so they cannot touch the shaft. Wipe the inside of the pulley with a rag to make sure
there are no small bits of dirt, grit, or machine shaving.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Push the new pulley onto shaft by wiggling at different spokes. Or you can wiggle, turn
pulley, then again wiggle the pulley at two different spokes, turn, etc. Continue until the
back of the pulley is “snug” against the rear spacer washer. Note: If this does not work put a
small piece of wood (block from a 2x4) against the center of the pulley. Then gently tap the
block with a small hammer. Rotate the pulley after a few taps to insure it goes on straight.
Continue until the back side of the pulley center is against the back spacer (Part No. 40) See
Figure, Parts, Page 17 in Operator’s Manual.
Turn pulley and make sure it turns smoothly and is not making any scraping sounds or feels
loose. You can inspect the back of the pulley with a small compact mirror and a flashlight
to insure the pulley is pushed far enough onto the shaft.
Clean all dirt and any oil on front bolt and washer from above Step 5 (Part No.’s 42, 41).
Put a few drops of thread sealant on threads. Then, replace lock washer, flat washer, and
front bolt. Tighten front bolt with a 7/16” wrench or socket.
Run the supplied safety wire through the drilled hole in the spoke of the pulley and hole of
the bolt head.
Bend the ends so they are of equal length side-by-side.
With a pair of vise grips, grip both wires then twist until they are braided to the bolt head.
CAUTION: DO NOT TWIST THE WIRE IN HALF.
With a pair of side cutters, cut off the excess leaving from ½ to 1 inch in length of twist.
Now, tighten both set-bolts with a 5/16” wrench or socket and ratchet.
Replace belt by attaching to small motor shaft at bottom then working belt onto new large
pulley.
Adjust belt tension so that there is approximately 1/4” deflection on either side of the belt
midway between the two pulleys (or 65-70 foot/lbs.) and tighten adjustment bolt. Check
belt tightness by pushing inward at mid-point between the pulleys. It should not stretch or
move inward more than a ¼” from its original position. If belt is too loose, refer to
replacing drive motor and belt tightening instructions on page 10 of the Operator’s Manual.
Note: This might be a good time to grease both bearings (Parts No.25). Squeeze a small amount (less
than 1 oz.) of white lithium grease in both front and back bearings. Locate the small yellow plastic cap
or plug on-top of the front bearings. Next remove the two screws to lift the top and lid assembly, pull
the top and lid assembly forward an inch or two, lift top and lid assembly up and locate the rear
bearings. Remove each cap then lubricate by pushing the nose of the small tube firmly into the hole.
Squeeze a small amount of white lithium grease into each opening. Replace the cap and wipe away any
excess. (White lithium grease can be bought in most auto part supply stores in a small 1.5 oz tube.)
STABER
INDUSTRIES, INC.
www.staber.com
4800 Homer Ohio Lane • Groveport, OH 43125 • Service Dept. Phone 614-548-0098 • FAX 614-836-9524
Replacing the Struts
1. Be sure you have disconnected the power to the washer.
2. Move the washer out in the open. Lay a piece of cardboard or a blanket
on the floor to protect the side of the washer.
3. Carefully lay the washer on its right side (facing the machine), and
remove the front panel by taking out the four (4) 5/16” screws that hold
the panel in place (located at the bottom of the front panel).
4. Locate the four struts.
5. Remove the four (4) nuts that hold the struts to the machines’ base.
6. Grab hold of the lower (narrower portion) part of the strut and push
towards the upper (wider portion) part of the strut. This will collapse the
strut enough to allow you to remove the lower part of the strut. Do this
for each strut you will be replacing.
7. Remove the nuts that hold the upper part of the strut in place. Remove the
upper part of the strut.
8. You now should have all struts out of the machine. In order to install the
new struts, all you have to do is reverse the order of what you just did.
You will need to hold back on the thin portion of the upper part of the
strut in order to tighten the nut.
9. After you have installed all of the struts, replace the front panel and
carefully stand the washer back to its original position.
10. Make certain that the tub assembly is positioned in the opening through
the top. Also, check to see if the skirt is down in the gray bezel properly.
11. If you have any questions, please call us at 614-548-0098 between 7-3
ET Mon.-Fri. and ask for technical support.
PARTS PRICING
• Pricing subject to change without
prior notice
• Shipping & handling are extra
• Parts normally shipped UPS Ground
within Continental U.S.
Date: 9-06-05 Pricing subject to change. Shipping & handling are extra.
Part Number Part Description
UOM List Price
810901 2 YEAR EXTENDED PART WARRANTY
EA
$ 199.00
811201 SEAL, SHAFT, 22X40X7TC
EA
$
4.53
811203 HUB GASKET
EA
$
1.20
811205 GASKET, SOAP/SOFTENER DISP.
EA
$
0.62
811207 GASKET, SOFTENER DISP.
EA
$
811209 P8612 1/8"X1/2" FOAM TAPE (36)
FT
$
0.24
811211 BOOT FOR WAX MOTOR
EA
$
2.17
811213 SWITCH INSULATOR (.015 FISHPA)
EA
$
0.25
811215 SHIELD, SOAP DISPENSER
EA
$
1.45
811217 AS568-114 O-RING
EA
$
0.35
811219 WASHER, FELT F10 .59X1.125X.25
EA
$
0.61
811221 GASKET, LIQUID/POWDER DISP.
EA
$
0.59
812201 BEARING, 6203-2RS
EA
$
7.38
812203 62012RS RADIAL BALL BEARING
EA
$
2.37
812205 62022RS RADIAL BALL BEARING
EA
$
2.51
813201 HARNESS ASSEMBLY, 2300 & 2301
EA
$ 65.54
813202 HARNESS ASSEMBLY, 2900
EA
$ 105.24
813203 ASSEMBLY, LID LOCK
EA
$ 23.15
813205 WAX MOTOR (100332.08) (500)
EA
$
7.25
813206 TIMER (HXW2900)
EA
$ 65.88
813207 TIMER (HXW2300)
EA
$ 62.58
813208 TIMER (HXW2100 & HXW2200)
EA
$ 65.88
813209 SELECTOR SWITCH, WASH TEMP
EA
$ 10.39
813211 SELECTOR SWITCH, PROGRAM
EA
$ 13.34
813212 MOTOR (AEG)
EA
$ 169.20
813213 1050-1-00-26610 IND. LAMP RED
EA
$
8.84
813214 1050-1-00-26640 IND. LAMP GRN
EA
$ 10.41
813215 PRESSURE SWITCH
EA
$ 18.66
813217 MOTOR-SIEMENS 1BA67 120V
EA
$ 169.20
813219 MOTOR CONTROLLER 2300-2302
EA
$ 178.50
813220 M0TOR CONTROLLER => (2303)
EA
$ 178.50
813221 POWER CORD, 120 VOLT
EA
$
5.56
813222 MOTOR CONTROLLER->2303 240V
EA
$ 178.50
813223 SELECTOR SWITCH, WATER LEVEL
EA
$ 13.34
813224 MOTOR CONT. SIEMENS W/STUDS
EA
$ 178.50
813225 PROX SWITCH-HAMLIN 59105-010
EA
$
9.56
813226 MOTOR CONT. SIEMENS W/HOLES
EA
$ 178.50
813227 HARNESS ASSEMBLY, 2100
EA
$ 67.62
813228 MOTOR-SIEMENS 1BA67 220V
EA
$ 169.20
813229 HARNESS ASSEMBLY, 2200
EA
$ 67.62
813231 1-282005-1 5 CIRCUIT CNCTR
EA
$
3.17
813233 FL1-2900 COIN DROP METER
EA
$ 375.00
813235 SWITCH, EMG STOP B412C11210000
EA
$
6.93
813237 EM. STOP SW. RETAINER ST-2619
EA
$
0.68
813239 1-282010-1 10 CIRCUIT CNCTR
EA
$
4.78
813240 EH688-008 8 CIRCUIT CNCTR
EA
$
813241 FAN MOTOR 29005-877
EA
$ 11.90
813243 OUT OF BALANCE SWITCH 402-9071
EA
$
9.10
813245 10 AMP CIRCUIT BREAKER
EA
$
3.50
$
813247 6" WIRE LEAD W/(2) 1/4' TERM
EA
0.63
813249
813251
813253
813255
813257
813259
813261
813263
813265
813267
813268
813269
813271
813272
813273
813275
813277
813279
813281
813283
813284
813285
813287
813289
813291
813293
813295
813297
813298
813299
813301
813303
813307
814201
814202
814203
814204
814205
814206
814207
814208
814209
814210
814211
814213
814215
814217
814221
814223
814225
814227
814229
2 POS RAST 5 KEYED FOR MOTOR
4 POS RAST 5 KEYED FOR LID LCK
8 POS RAST 5 KEYED FOR MOTOR
2 POS RAST 5 KEYED FOR PUMP
4 POS RAST 5 KEYED FOR PRES SW
8 POS RAST 5 KEYED FOR PRES SW
WIRE HARNESS, 2302
RELAY, SINGLE POLE DBL. THROW
801-9001 OUT OF BALANCE SWITCH
X55778 M620 QCS/BI TIMER 2303
X55778 M620 QCS/BI TIMER 240V
SOAP DISP. RETROFIT HARNESS
WIRE HARNESS, 2303-2304
3AG 250 MA S/B FUSE-PIGTAIL
SOAP DISPENSER RETROFIT FUSE
SOAP DISPENSER FUSE HARNESS
1 AMP AGC 250 VOLT FUSE
S8202-1 (354901GY) FUSE HLDR
F72-W2006-I4 CANADIAN COIN
INDICATOR LIGHT RED 240V
INDICATOR LIGHT GREEN 240V
POWER CORD, 240V, AUSTRALIA
REV 6 MOTOR CONTROLLER ASMBLY
F72-W2007-I4 AUSTRALIAN COIN
WIRE HARNESS, 2901
F72-W2004-I4 AMERICAN COIN
EST 200 120V60HZ ELE. STEPPER
POWER CORD, UK EE00-1310
4B629 MOMENTARY PUSHBTN 22MM
4B656 PUSHBUTTON CONTACT NO
WIRE HARNESS, PUSH TO START
MOTOR CONTROLLER 2304-34-44
432 ACCEPTOR, R9 1044/950
PUMP, 120V
92515400 PUMP BRACKET
VALVE, WATER INLET N51 K-68847
HOSE, WATER INLET SUPPLY-BLUE
HOSE, WATER INLET SUPPLY-COLD
HOSE, WATER INLET SUPPLY-HOT
HOSE, VALVE TO SOAP BOX
HOSE, WATER INLET SUPPLY-RED
HOSE, INTERNAL WATER SUPPLY
HOSE, WASHER FILL BL12-48WA
HOSE, PRESSURE SWITCH
HOSE, SUMP 5303203035
HOSE, DRAIN 27023F-072
102-0396 CLAMP, SUMP TO PUMP
CP-24 CLAMP, PUMP TO DRAIN HSE
CP10202 CLAMP, MIX VLV TO FABR
WASHER, GSW-300 HOSE
CP-5 PRESSURE TUBE HOSE CLAMP
TUBING, 3X16"X5/16" G.P.
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
FT
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
0.34
0.58
0.87
0.34
0.58
0.87
84.49
12.56
9.10
62.58
39.87
4.20
98.19
3.09
1.76
1.92
0.41
1.98
483.57
2.51
3.23
8.82
160.36
354.57
117.87
96.86
161.58
11.07
15.27
25.59
95.01
182.40
49.45
21.84
8.47
8.47
1.52
15.61
18.42
3.59
15.70
12.65
0.29
0.33
0.16
0.04
0.14
0.20
814231
814233
814234
814235
814237
814239
814241
814243
814245
814247
814249
814251
814253
814255
814257
814259
814261
817101
817102
817103
817105
817107
817109
817111
817113
817114
817115
817116
817117
817118
817119
817120
817121
817122
817123
817124
817125
817126
817127
817128
817129
817130
817131
817132
817133
817135
817137
817138
817139
817141
817143
817144
20690410 DUMP VALVE
HOSE, WATER INLET-COLD EXPORT
HOSE, WATER INLET-HOT EXPORT
PUMP, 240V
VALVE, WATER N-51 K56968-SB1H
VALVE, WATER N-51 K56968-6
VALVE, DISPENSER N-71 K74833
VALVE, DISPENSER N-71 K74868
3T-38 PP 3/8" BARB TEE STD
HOSE, 3/8" X 2-5/8"
HOSE, 3/8" X 3-1/2"
HOSE, 3/8" X 4-3/4"
HOSE, 1/2" X 3-1/4"
CLAMP, HOSE HC-10-STPA
CLAMP, HOSE HC-11-STR
CLAMP, HOSE HC-14-STR
TUBING, 3/8"X5/8" G.P.
ASSEMBLY, OUTER TUB
ASSEMBLY, OUTER TUB L/P DISP.
ASSEMBLY, INNER TUB
ASSEMBLY, BEARING HUB
ASSEMBLY, DRIVE SHAFT
ASSEMBLY, SUPPORT SHAFT
ASSEMBLY, BASE
ASSEMBLY, CABINET
ASSY., TOP LIQ/PWDR TOP (240)
ASSEMBLY, FRONT
ASSEMBLY, FRONT COIN
ASSEMBLY, TOP LIQUID DISPENSER
ASSY., TOP LIQ/PWDR DISP (120)
ASSEMBLY, LIQUID DISPENSER
ASSEMBLY, SOFTENER DISPENSER
ASSEMBLY, CONTROL PANEL-2100
ASSEMBLY, LIQUID/POWDER DISP.
ASSEMBLY, LID
ASSEMBLY, L/P COMMERCIAL DISP.
ASSEMBLY, CONTROL PANEL-2200
ASSEMBLY, TOP L/P COIN
ASSEMBLY, CONTROL PANEL-2300
ASSY, CONTROL PNL PUSH TO STRT
ASSEMBLY, CONTROL PANEL-2900
ASSEMBLY, CON PNL-2901 IMONEX
ASSEMBLY, COIN VAULT & TUBE
ASSEMBLY, CON PNL-2901 HEINKE
OWNERS MANUAL KIT
ASSEMBLY, PULLEY
ASSEMBLY, LOCK ROD
ASSEMBLY, COMMERICAL BEZEL
ASSEMBLY, PRESSURE SWITCH HOSE
ASSEMBLY, BALANCE SWTCH (2301)
ASSEMBLY, SEE-THROUGH FRONT PL
ASSY., DISPENSER VALVE 240V
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
FT
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
5.73
5.73
34.45
21.84
21.84
27.75
35.10
0.75
0.45
0.48
0.57
0.69
0.10
0.07
0.12
0.50
396.95
379.42
225.74
27.14
15.82
12.54
149.00
84.11
330.80
72.05
49.05
312.14
312.14
57.02
17.40
164.91
7.64
71.78
13.57
171.56
318.07
187.43
185.58
394.69
394.69
64.75
470.69
7.50
39.74
49.19
7.55
15.48
16.59
75.00
45.04
817145
817146
817147
817148
817149
817150
817151
817152
817153
817155
817156
817157
817159
817161
817163
817165
817167
817168
817169
817171
817173
817174
817175
817176
817201
817202
817203
817205
817213
817214
817215
817216
817217
817218
817219
817220
817221
817222
817223
817225
817226
817228
817229
817230
817231
817232
817233
817239
817241
817243
817245
817247
ASSEMBLY, SEE-THROUGH LID
ASSY., DISPENSER VALVE 120V
ASSEMBLY, WATER VALVE 120V
ASSEMBLY, WATER VALVE 240V
ASSEMBLY, CONTROL PANEL 2302
ASSY., MASTER WATER VALVE 120
ASSEMBLY, SOAP DISP RELAY KIT
ASSY., MASTER WATER VALVE 240
ASSEMBLY, DOOR HOOK
ASSY., CONTROL PNL 2303-04 120
ASSY., CONTROL PNL 2304 (240)
P.O.P. DISPLAY
ASSEMBLY, CABINET STAINLESS
ASSEMBLY, FRONT STAINLESS
ASSEMBLY, SUSPENSION COVER
ASSEMBLY, FRONT COIN SS
ASSEMBLY, CONTROL PNL COM 120V
ASSEMBLY, CONTROL PNL COM 240V
ASSEMBLY, BASE STAINLESS
ASSY., WATER SHEILD C/B
ASSY., HEAT SPREADER W/STUDS
ASSY., HEAT SPREADER W/HOLES
ASSY., HEAT SPREADER COIN PCB
ASSEMBLY, IMONEX FACE PLATE
OUTER TUB SIDE
OUTER TUB SIDE, L/P DISP.
OUTER TUB SIDE WITH HOLES
OUTER TUB BAND
OUTER TUB STRUT SUPPORT (88)
MOTOR ADJUSTMENT STUD
BRACKET, FRONT MOTOR MOUNT 288
MOTOR PIVOT SHAFT
WEIGHT, OUTER TUB REAR COUNTER
BRACKET, REAR MOTOR MOUNT 2100
WEIGHT, OUTER TUB STRUT
BUSHING, MOTOR PIVOT SHAFT
INNER TUB SIDE
WASHER, SPACER
BAND, INNER TUB
HINGE PIN
GUARD, RIGHT CLOTHES
GUARD, LEFT CLOTHES
SPRING, HOOK HINGE
SAFETY LATCH
DOOR, HOOK
HOOK FOR DOOR (450)
DOOR, LOUVER
HUB, CASTING
SHAFT, DRIVE
SHAFT, SUPPORT
FLANGE, DRIVE SHAFT (325)
FLANGE, SUPPORT SHAFT (450)
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
45.00
37.69
24.93
37.83
217.05
26.21
14.84
37.52
36.51
193.81
192.29
50.00
148.43
112.05
6.75
91.16
203.59
174.57
198.05
10.19
9.76
8.86
8.85
18.43
18.95
18.35
33.07
6.72
2.66
2.33
6.24
6.04
0.69
3.14
3.63
16.05
1.07
80.42
1.60
1.46
1.46
1.29
2.05
9.62
4.22
28.37
11.30
9.39
6.52
3.25
2.84
817249
817251
817252
817253
817255
817259
817261
817263
817265
817267
817269
817271
817272
817273
817274
817275
817277
817279
817281
817282
817283
817284
817285
817286
817287
817288
817289
817291
817293
817295
817297
817298
817299
817300
817305
817307
817310
817311
817312
817313
817314
817315
817316
817317
817318
817319
817321
817323
817325
817327
817329
817331
SPACER, 5.00 MM
PULLEY, 14" DRIVE
MAGNET, DR. PULLEY CR551209098
ASSEMBLY, STRUT
CHANNEL, BASE (42)
ANGLE, BASE (57)
ANGLE, FRONT
NUT, 3/8"X16 WELD 08-3324
LEG, 3/8 X 16 LEVELING (400)
FOOT PAD (LC0875)
BRACKET, PUMP (1110)
CABINET
GUSSET, CABINET (420)
FRONT PANEL
FRONT PANEL, COIN (2900)
KICK PANEL (21)
BRACE, FRONT PANEL TOP (36)
TOP
BOX, SOAP / SOFTNER
BOX, SOFTNER
CONTROL PANEL - 2200
HAT CHANNEL HXW2100-HXW2300 60
CONTROL PANEL OVERLAY HXW2100
CONTROL PANEL OVERLAY HXW2200
CONTROL PANEL OVERLAY HXW2300
CONTROL PANEL OVERLAY HXW2900
LID
LID LOCK PIN
BELT, DRIVE 560J6
BRACKET, WATER VALVE (96)
BEZEL, OUTER TUB (2300-2303)
BEZEL, OUTER TUB (2304)
SKIRT
SPRING, BEZEL
BRACKET, TUB STRUT WEIGHT 210
BRACKET, TUB BACK WEIGHT (315)
CONTROL PANEL - 2900 HEINKE
LIFTING VANE
CONTROL PANEL - 2100
CONTROL PANEL - 2900 KELTNER
CONTROL PANEL - 2300 (33)
HAT CHANNEL HXW2900 KELTNER
HAT CHANNEL HXW2900 HEINKE
PRESS NUT UP51-1420 GM6046
CLS-0420-1 1/4X20 PEMM NUT SS
HINGE, TOP (1400)
BRACKET, TOP HOLD DOWN (2516)
BRACKET, LID LOCK (336)
CLIP, WATER PRESSURE SWITCH
BRACKET, FAN FOR MOTOR
FAN BLADE
BRACKET, TOP REINFORCEMENT
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
2.63
30.33
0.44
18.12
6.20
5.64
6.62
0.16
0.47
0.23
0.80
44.19
2.85
12.44
12.30
3.48
3.76
181.99
10.50
9.66
10.19
6.69
14.80
14.80
14.72
14.80
89.36
2.69
22.88
3.80
37.79
37.79
7.01
1.84
2.93
2.87
11.39
3.82
10.19
11.39
10.90
7.50
7.50
0.07
0.85
1.19
1.15
2.92
0.41
0.52
2.17
0.48
817333
817335
817337
817339
817341
817343
817345
817347
817349
817351
817353
817355
817357
817359
817361
817363
817364
817365
817366
817367
817368
817369
817370
817371
817373
817375
817377
817379
817381
817383
817385
817387
817389
817391
817393
817395
817397
817399
817401
817403
817405
817407
817409
817411
817413
817415
817417
817419
817421
817423
817425
817427
INNER TUB COUNTER BALANCE WGHT
OUTER TUB BRACE
BRACKET, OUT OF BALANCE SWITCH
CABINET PAD
SEE-THROUGH FRONT PANEL
PLASTIC INSERT FOR SEE-THROUGH
SEE-THROUGH LID
BEZEL, LIQUID DISP. 2300-2303
RETAINER, SKIRT
FLANGE COVER
PRESSURE SWITCH BRACKET
LID HINGE TOP REINFORCEMENT
BRACKET, OUT OF BALANCE SWITCH
BRACKET, OUTER TUB STOP
WASHER, SUSPENSION COVER
SOAP DISP. WAX MOTOR SHEILD
SOAP DISPENSER FLOW RESTRICTOR
SOAP DISPENSER BODY 2304
SOAP DISPENSER DEFLECTOR
SOAP DISPENSER TRIM BEZEL 2304
COMM. SOAP DISP TRIM BEZEL
PREWASH FLOW RESTRICTOR
SOAP DISPENSER SIPHON
CABINET, STAINLESS
GUSSET, CABINET STAINLESS
FRONT PANEL, STAINLESS
KICK PANEL, STAINLESS
BRACE, FRONT PANEL TOP SS
CONTROL PANEL OVERLAY HXW2303
SUSPENSION COVER TUBE
HXW2503 COMMERICAL OVERLAY
FRONT PANEL, COIN S.S.
BRACKET, OUTER TUB STOP S.S.
RNZ-3316 STAINLESS WELD NUT
CHANNEL, BASE STAINLESS (42)
ANGLE, BASE STAINLESS (57)
BRACKET, PUMP STAINLESS (1110)
BRACKET, WATER VALVE STAINLESS
COIN TUBE
COIN TUBE MOUNT
VAULT DOOR
COIN RAKE
LOCK ROD
98381A508 PIN, LOCKING
PIN, ANTI-ROTATION LOCK
98407A134 "E" RETAINING RING
LOCK, N1058A W/2 KEYS 2400S
VAULT BODY
VAULT COLLAR
VAULT BACK
98381A505 STOP PIN FOR RAKE
COIN INLET
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
2.27
1.98
1.64
0.55
28.81
34.43
25.61
5.97
1.43
2.97
0.47
0.53
16.60
3.29
1.36
2.79
0.44
11.70
0.48
2.18
2.27
0.44
0.67
120.77
1.78
43.86
9.46
5.30
13.04
3.11
7.20
43.86
3.47
1.39
14.44
11.71
1.11
3.74
56.56
3.08
6.09
4.33
4.88
0.48
0.48
0.25
38.79
11.18
3.81
0.92
0.44
-
817429
817431
817433
817435
817437
817439
817501
817502
817503
817505
817507
818201
818203
818204
818205
818207
818209
818211
818213
818217
818219
818221
818223
818225
818227
818229
818231
818234
818235
818237
818239
818241
818243
818245
818247
818249
818251
818253
818255
818257
818259
818260
818261
818263
818265
818267
818269
818271
818273
818275
818277
818279
VAULT UPRIGHT
LOCK, SIPHON TUBE
92395A113 INSERT, PRESS KNURL
91772A146 18-8 SS PAN PH SCREW
DOOR STOP
SUMP HOSE HANGER
WATER SHEILD BASE
WATER SHEILD FRONT
CONTROL PANEL, PUSH TO START
HEAT SPREADER 2304-34-44
HEAT SPREADER, COIN BOARD
BOLT, 1/4X20X5/8 SS HH 70002
1/4X20X1/2 SS FLT SKT CS 73880
1/4X20-1/2 BUTTON HEAD CAP SCR
KNOB, SMALL BLACK
KNOB, LARGE BLACK
INDICATOR DIAL, BLACK
8X1/2 HWSL SMS ZINC 31067
LOCATOR, DR. RIVET 61PSS40000
10X1/2 HWH DRILL KWICK TEK2
1000-50 MOTOR SHAFT RET. RING
POWER CORD STR/RELIEF 1484
90295A187 MOTOR SHFT NYLON WSH
5/16 FLAT METAL WASHER 33006
3/8X16 NUT FOR LEVEL LEG 36106
5/16X18X3/4 BOLT ADJ STD 13053
MOTOR LEG GROMMET
OWNER'S GUIDE (2100,2200,2300)
MANUAL, OWNERS HXW2302-2303
PANEL NUT FOR SWITCH ST-2590
1/8DX3/16G CS ALU RIVIT 41008
#6X1/2 TRUSS HD PHL SMS 71780
10-32X1/2 HH MS 27553
3/16X1-1/2" TUBE CPLR VC316ABK
SCREW, GREEN GROUND
MOTOR PIVOT SHFT GROMMET NM457
561-LT500 CNTRLR STAND-OFF
1/8" DX1/8" G SS RIVET SS/SS42
10X1/2 TSMC 1.10A12PS
0711-A60 LID BUMPER
HCMP06B12-M20 WIRE HARN CLIP
03410087-B03LL HARNESS CLP
5/16X18X4 HH CAP BOLT GRADE 2
5/16X18 NUT 36104
5/16 LOCK WASHER 33620
5/16X18X2 1/2 CU PL WELD STUD
2" O.D. HOSE GROMMET (1000)
081-0005-03 8-32X1/2 CP W STUD
CLIP, CONDUIT 22CC37C0375B
CONDUIT, PLASTIC CLT38F-C20
OUTER TUB STOP
#10X5/8 PLASTITE SCREW SQ343->
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
FT
EA
EA
$
1.73
$
1.04
$
0.47
$
0.08
$
1.13
$
2.02
$
3.57
$
2.20
$ 11.00
$
4.27
$
4.27
$
0.13
$
0.32
$
0.27
$
3.00
$
3.50
$
3.00
$
0.10
$
0.75
$
0.05
$
0.07
$
0.17
$
0.22
$
0.05
$
0.07
$
0.12
$
0.58
$
2.45
$
7.00
$
0.09
$
0.07
$
0.10
$
0.14
$
0.53
$
0.08
$
0.88
$
0.31
$
0.14
$
0.61
$
0.17
$
0.55
$
0.46
$
0.35
$
0.04
$
0.04
$
1.31
$
0.45
$
0.22
$
0.05
$
1.26
$
1.59
$
0.36
818281
818283
818285
818287
818289
818291
818293
818295
818297
818299
818301
818303
818305
818307
818309
818311
818313
818315
818317
818318
818319
818321
818323
818325
818327
818329
818331
818333
818335
818337
818339
818341
818343
818345
818347
818349
818351
818353
818355
818356
818357
818359
818361
818363
818365
818366
818367
818369
818371
818373
818375
818377
8-32X5/16 HEX MACH K-NUR 37406
3/16" POP RIVET 1/8G SS/SS62
1/4" LOCK WASHER 33618
SS/SS 46 1/8"X3/8" SS RIVET
10X24X3/4 HH MACH SCREW
SOAP/SOFTENER LABEL
1.250X.260X.125 WASHER (2592)
4X5/8 PHIL-OVAL SMS S.S. 72244
4X1/2 P PH 25-BT TCS 32259
22CC50D1250B CABLE/HOSE CLAMP
#8X3/8" STAND OFF
29.6D3.0 NAT. 1 OUNCE DISP CUP
081-0005-07 8-32X1 CP W STUD
6-32X7/8 P H S M S 27322
6-32 NYLOC NUT 37010
CONDUIT, PLASTIC 7202500021BOX
PD219385SOG PAL NUT
4-40X5/8 PH PHIL MACH SC 28661
4-40 HEX NUT NYLOC 37006
#4 EXTERNAL LOCK WASHER 33731
5"X5" 120 PARTICLE CHIP BOARD
5ZW13 10X14X.002 PLASTIC BAG
WATER SHIELD FOR STRUT
8-32X1/4 MS PAN HEAD 27357
C-9031-6Z-67 U-CLIP
ENERGY TAG
8-32X3/8 RH MS (27369)
1/8D X 1/4G ALXAL RIVET 41009
VC 437-8 VINYL RED CAP
KNOB, SMALL WHITE (2300-02)
KNOB, TIMER WHITE (2300-02)
INDICATOR DIAL, WHITE 2300-02
WW-00 HOLE PLUG YELLOW
SAFETY DECAL (NEON ORANGE)
SOAP/SOFTENER DECAL
1/4X20X5/8 GR5 W/HOLE IN HEAD
2035T2 CLIP FOR SOAP DISP
KNOB, SMALL WHITE (2303)
KNOB, TIMER WHITE (2303)
INSERT, CENTER TIMER KNOB WHT.
INDICATOR DIAL WHITE (2303)
SPRING INSERT FOR KNOB - 6200
.029X9" SAFETY WIRE 9495K24
KNOB, SMALL BLACK (2303)
KNOB, TIMER BLACK ASSY. (2303)
INSERT, CENTER TIMER KNOB BLK.
INDICATOR DIAL BLACK (2303)
INSTRUCTION LABEL
8507K144 BLACK EDGE TRIM
#8X1 PHIL P/H S.S. BT 72918
.003 DEAD SOFT ALUMINUM X 1"
WASHER, FLANGE COVER
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
FT
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
FT
EA
EA
EA
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
0.07
0.35
0.02
0.36
0.13
1.06
0.76
0.11
0.04
0.29
0.08
0.14
0.25
0.10
0.06
0.19
0.13
0.03
0.05
0.02
0.24
0.45
0.21
0.08
0.18
0.54
0.09
0.07
0.23
3.00
3.50
3.00
0.06
1.22
0.53
1.64
0.24
3.00
3.50
0.10
3.00
0.08
0.30
3.00
3.50
0.10
3.00
2.05
1.77
0.08
0.42
0.83
818379
818381
818382
818383
818384
818385
818386
818387
818389
818391
818393
818395
818397
818399
818401
818403
818405
818407
818409
818411
818501
818502
818503
818505
818507
818509
818511
818513
818515
818517
818519
818521
818523
818900
818901
818902
818903
818905
818907
819001
819002
819003
819005
819007
819009
819011
819013
819015
819017
819019
819021
819023
RETAINING RING 3100-75
081-0004-05 6-32X.750 CP W STD
13SP053 SP53 NYLON SPACER
0500632SCN THUMB NUT
081-004-01 6-32X.25 CP W STUD
FH-632-12 6-32X3/4 PEM STUD
081-0003-03 4-40X1/2 WELD STUD
FH632-4 6-32X1/4 PEM STUD
FH-832-10 8-32X5/8 PEM STUD
FH-024-8 10-24X1/2" PEM STUD
SO632-12 6-32X3/8" STAND OFF
13SP041 1/4" PLASTIC SPACER
10-24 KEPT NUT 37407
FH-440-12 4-40X3/4" PEM STUD
9600K37 GROMMET, SOAP HOSE
BOTTLE, 4 OZ. EP-18504
CAP, PUSH/PULL DD-20431
CUP, GREASE 150750
GREASE, SYRINGE 7510A653
ABSORBER SIDE PANEL
SHIPPING TUBE
30X26.5X57X.002 BLACK BAG
TOP & BOTTOM CAP
FRONT POST
BACK POST
INNER TUB INSERT
BOTTOM BASE
MPC126OB POLYESTER STRAPPING
BLOCK, BOTTOM BASE
BOX, FRONT PANEL KIT
BOX, SEE-THROUGH LID
33X30 PALLET
BOX, DETERGENT
STABER LAUNDRY DETERGENT
4 COLOR SALES SHEET
DISPENSER, PUMP
SALES BINDER
SERVICE BINDER
SALES VIDEO
18GA 439 2D S.S. COIL 48.25"
18GA 304 2B S.S. SH 26X65
20GA CRS 48X96 SHEET
11 GA 304 S.S. #4 48X120 SHEET
11 GA HR P&O 48X96 SHEET
1.0" 303 M/Q S.S. RND 12' RND
.063 3003 H14 MF ALUM. 48X96
1/2" 12L14 HEX 12' RANDOM
1/2" 12L14 ROUND 12' RANDOM
14GA CRS 48X96 SHEET (.075)
20GA CQ 37X93.75 SHEET (CAB)
20GA CQ 36X32 SH (FRONT)
.236X48X96 ACRYLIC CLEAR SHEET
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
EA
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
0.15
0.10
0.05
0.08
0.13
0.07
0.13
0.06
0.08
0.08
0.26
0.06
0.05
0.07
0.40
1.35
9.95
34.45
0.87
4.44
3.67
3.02
1.28
2.15
219.33
4.06
26.16
5.17
9.30
14.99
0.10
3.00
10.00
10.00
1.35
2.48
3.84
0.83
2.94
0.79
5.02
3.87
1.89
1.38
1.65
0.92
0.91
171.84
819025
819027
819029
819031
819033
819034
819035
819037
819039
819041
819043
819045
819047
819049
819901
819902
819903
813261M
813271M
813291M
813301M
817223B
817239M
.080X48X96 LEXAN SHEET PLSH25
1.375X.065 WALL X20' DOM TUBE
2.5X2.5X.120 SQUARE TUBE
1.50X.125 STRAP IRON
1/4" HR P&O 4'X8'SHEET
3/16" HR P&O 4'X8' SHEET
.375 1018 ROUND RANDOM BAR
20GA 304 #3-4 SS 36X120 SHEET
3.0X3.0X.187 SQUARE TUBE
1.0"X.156" WALL DOM TUBING
.020X.750 301 SS #5 EDGE COIL
1/8" X 12' RANDOM 304SS BAR
1" ROUND 12L14 BAR
1.375X.066 WALL X12' 6061-T6
819901 SAFETY BOLT INST. SHEET
819902 SOAP DISP RELAY INST SH
819903 BEARING REPL. INST SH.
HARNESS ASSEMBLY, 2302
HARNESS ASSEMBLY, 2303-2304
HARNESS ASSEMBLY, 2901
HARNESS ASSEMBLY, PUSH TO STRT
SHEET, INNER TUB BLANK
HUB, MACHINED
EA
FT
FT
FT
LB
LB
LB
LB
FT
FT
LB
LB
LB
FT
EA
EA
EA
EA
EA
EA
EA
EA
EA
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
$
242.40
6.52
4.65
0.71
1.15
0.78
1.50
3.54
8.19
6.00
15.63
8.70
1.05
4.80
0.48
0.48
0.48
54.77
64.29
249.87
97.02
41.40
12.01