Nuevo L.I. E95H.cdr

Ref.- 02 L.I. E95H .... \Nuevo L.I. E95H.cdr
RiveDrill
Instruction
Manual
RiveDrill
E95H
1
D.I.Y
D.I.Y
Rivet Drill Attachment
Rivet Drill Attachment. Compatible with most 10mm chuck drill drivers.
Suits 3.2/4.0/4.8mm Rivets (1/8” 5/32” 3/16”). interchangeable 3 nose
pieces (included) to suit common rivets.
Quick & Easy Riveting. Takes the effort out of riveting
RiveDrill
Movies
Watching videos
demonstration on
You Tube
Seeking "RiveDrill”
Specification
Career maximum
traction: 10mm
Maximum Tensile
Strength: 6,000 Newton
Jaws: 2 units
Measure: 150mm x
¨60mm
Weight: 280 grams
Pieces
3Nose
Included
Inner hole
position indicator
Attaching RiveDrill To
Your Drill (Any Brand)
Operating RiveDrill
D
2
4
C
1
3
IOption manual use
Caution: The external sleeve should be held during operation of RiveDrill. It is designed for protection
against the rotating chuck when operating RiveDrill and should cover the chuck at all times.
E
Right
Le
ft
D) Set your drill to reverse
rotation. Depress the
trigger switch until your
hear a “clicking” sound
from the RiveDrill.
B
A
A) Pull the external sleeve (1) to the front
of the RiveDrill, exposing the drive shaft (2).
B) Insert drive shaft into drill chuck in the
same manner as a drill bit. Tighten chuck.
C) Pull the external sleeve (4) for back to
cover the drive shaft and chuck.
Nose
piece
E) Insert a rivet into the nose
piece, ensuring that the size
of the rivet matches the size
of the nose piece. Do not
force rivet into RiveDrill as this
could cause damage.
Click,
click...
Click,
click...
Instruction Manual
Drive Shaft: 9 mm
hexagon
Outer sleeve for hand
safety: Yes
Inner hole position
indicator: Yes
Nose Piece included: 3
units
Outer sleeve for
hand safety
Drive
Shaft
Opening.
Closing.
F
Opening
G
Lef
Closing
ghdopsertil
R
F) Set your drill to forward
rotation (low speed).
Insert the rivet fully into
your workpiece. Apply
firm pressure to the drill
and depress the trigger
switch until the rivet pops.
Right
t
G) To remove the rivet`s
mandrel from the RiveDrill,
set you drill to reverse rotation
and depress the trigger switch
until the mandrel is released
from the nose piece.
“Clicking”
More information: www.rivedrill.es - [email protected] - Fax (Madrid Spain) +39 913526577
Ref.- 02 L.I. E95H .... \Nuevo L.I. E95H.cdr
RiveDrill
Instruction
Manual
RiveDrill
E95H
2
D.I.Y
D.I.Y
The hole should be 0.2mm to 0.4mm larger than the
Rivet diameter.
3.2mm
3.4mm
Rivets
Recommended rivet sizes and rivet materials
suitable for use with the RiveDrill Table 1 and Table 2.
WARNING: Using rivet sizes and materials not shown
in these tables may damage the RiveDrill and will
not be covered by the warranty.
Mandrel
¨M
mandrel
diameter
L
mandrel
length
Do not use rivets "Z"
greater than 10mm
R
rivet
length
¨D
rivet diameter
“Z”
Maximun 10mm
To "Z" greater than
10mm using
model "RiveDrill HP”
(career maximun
traction 30mm)
Substituting
Nose Pieces
Table 2
qM
Rivet
5.2mm
4.3mm
Table 1
qD
3,2mm
1/8”
4,0mm
5/32”
4,8mm
3/16”
4.8mm
4.0mm
qD
ØD
L
qM
>1.8mm
<2.4mm
>2.0mm
<2.2mm
>2.7mm
<2.8mm
Rivet
ØD
3,2mm
1/8”
4,0mm
5/32”
4,8mm
3/16”
L
>26mm
<31mm
>26mm
<33mm
>29mm
<34mm
Material
Alum.
Steel
St. St.
Important Suggestions
Hole
RiveDrill break.
Warranty not included.
Rivet more expensive.
> 10 mm
Optimal Quality
> 4 mm
< 10 mm
OK
Opening
Ø4,0mm
Ø5/32”
Ø4,8mm
Ø3/16”
4
5
Closing
Righ
Left
t
3
ghdopsertil
R
First, eliminating pressure between jaws
and nose piece.
Seconds, remove the nose piece. Each
nose piece for each rivet.
Third, jaws move forward.
Ø3,2mm
Ø1/8”
Operating RiveDrill in Corners
1.2
1.1
1.5
Parts RiveDrill E95H (D.I.Y)
1.3
1.1 - Complete body
1.2 - Complete rotor
1.3 - Complete jaw holder
1.4 - Nozzle (one piece)
1.5 - Jaw (two pieces)
Spare Parts
R
dgohpsertli
R
dgohpsertli
User Maintenance.
R
dgohpsertli
When applying rivets it is important to ensure that
the mandrel is completely inside the nose piece of
RiveDrill. This is especially important when applying
rivets in corners or tight areas where it is not possible
to keep RiveDrill perpendicular to the worpiece.
Following this procedure will ensure the longevity of
the jaws. Failure to do so may cause dam,age to
the jaws.
1.4
Warranty. Declaration of the manufacture according to 93/37/EC.
More information: www.rivedrill.es - [email protected] - Fax (Madrid Spain) +39 913526577