ZMI 001 2000102867-KEPACSL-SBF-Installation EN(2.43

DRINKING FOUNTAIN INSTALLATION
For All Universal Split Level KEP( )ACSL-SBF Fountains With
Sports Bottle Filler
A. INSPECTION
Inspect the water cooler, water fountain and cartons for evidence of rough handling and concealed damage. Damage claims should be
filed with the carrier.
B. TO PUT WATER COOLER AND FOUNTAIN INTO SERVICE
1. NOTE: Provincial and local plumbing code may prohibit the use of saddle tapping valves for water line connection in some applications. All connections must conform to applicable plumbing codes.
2. The KEP8ACSL is composed of a water cooler and a water fountain. The water cooler contains the refrigeration system and is
always mounted on the right side. This unit can be configured with the water cooler high or low. Refer to the proper roughing in
drawing for location of plumbing and electrical service.
3. FLUSH BUILDING WATER SUPPLY BEFORE INSTALLING UNIT.
4. Install wall hangers as shown on the desired roughing in drawing. Wall hangers are shipped fastened to the backs of the unit. Units
with factory installed filters have additional instructions on a label inside of the access panel. Read these before installing the unit.
5. This unit has been factory assembled for right side high installation. To convert for right side low installation:
a) Remove the patch plate from the left side panel of the water cooler and install on the right side panel of the water fountain reusing the two mounting screws. The two bottom screws from each side panel may be temporarily removed to improve access.
b) Remove the screws holding the waste drain tubes from the cooler tops. The shorter drain will be used on the water cooler and
the longer drain will be used on the water fountain. Make sure that the waste drain gaskets are properly installed.
6. Mount the water cooler on the right hanger.
7. Straighten the inlet “Water In” tube in the water fountain. Mount the water fountain on left side hanger while routing the “Water
In” tube through the access hole to the water cooler. Remove the plug from the “Drain/Remote Cold Water” connection and insert
the “Water In” tube.
8. All provided waste drain parts for field installation are packed in the water fountain. Assemble the drain per the appropriate roughing in drawing. The short leg of the crossover piece will be on the water cooler side. When the unit has an internal waste trap,
the trap should be wrapped with insulating tape to prevent sweating. The use of the 1 3/4" knockout for a waste line is not recommended because of a potential conflict with ADA* toe space requirements. Check with your local building code inspector for approval.
9. Install a shut off valve in water supply line. Remove the strainer from the cooler “Water Supply” tube. Solder 3/8" inlet tube extension (furnished) with lead free solder to “Water Supply” tube and insert the strainer in open end of extension. Connect extension
to shut off valve to allow access to strainer for service, this connection should not be a solder or flare joint. To ease removal of the
strainer, a sheet metal screw may be lightly threaded into the open end.
10. Rotate the fan blade by hand to see that it is free of obstructions.
11. Check the available power supply against the water cooler data plate to assure correct electrical service. Plug power supply cord
into wall outlet. The rear most 1 3/8" diameter knockout in the frame bottom is for an externally located electrical supply. Make
sure the knockout hole edge is smooth and free of any burrs. Use of a Heyco busing #2184 in the knocked out hole is recommended in order to prevent damage to the service cord and to close up excess opening around the cord. Route the cord so it
does not interfere with ADA* space requirements.
12. To fill the cold water tank on the water cooler, open the water supply line shut-off and push any one of the front pushbuttons to
allow water to flow to the bubbler. On The EE model, actuate the solenoid by holding one hand approximately 3 inches from the
infrared sensor. Run water until stream is free of bubbles.
13.To adjust bubbler stream:
a) All pushbutton models are equipped with a cartridge regulator. The KEP8ACSL and KEPACSL have a slot in the shelf below the
pushbuttons. Insert a screwdriver in this slot to adjust regulator. Turn adjustment clockwise to increase stream height. To access KEPV8ACSL adjustment, remove the bezel and button from the front of the cooler.
0615
2000102867
1
DRINKING FOUNTAIN INSTALLATION
For All Universal Split Level KEP( )ACSL-SBF Fountains With
Sports Bottle Filler
b) Electric eye (EE models have a regulator built into the bubbler. If adjustment is needed, insert a 5/64" wrench approximately 1
1/8" into the bubbler nozzle opening until it bottoms out and is seated in an adjust screw. Turn the adjust screw clockwise to
reduce the stream heigh or counterclockwise to increase the height. Note, less than one turn is required to go from a closed
to a wide open flow. Do not overtighten the adjuster in the closed position as stripping the hex impression in the adjust screw
may result.
14.To adjust the beam range of the sensor (EE model only):
a) Shut off the water and power supplies.
b) Remove the two screws from the top front.
c) Remove the eight screws from the bottom of the nose that holds the nose to the shelf.
d) Remove the nose to gain access to sensor adjusting screw located between the two lenses.
e) The screw can be turned a maximum of 3/4 turns. Turn screw counterclockwise to decrease range. The sensor has an adjustable range of 24" to 48". It is factory set at 27". There is a non-adjustable on-time delay of .75 seconds to prevent nuisance
actuation of the solenoid valve should someone walk by. After drinking, the water will shut off immediately after walking away.
Maximum run time is 30 seconds should someone tamper with the sensor. NOTE: Walls with a reflective finish, i.e., ceramic
tile,across from the sensor may cause false actuation no matter what the sensor adjustment is for distance. Therefore, do not
install the unit in such an area or dull the surface of the wall so it will not reflect light.
C. MAINTENANCE
The only maintenance operation required is the removal of dirt and lint from the condenser of the water cooler. Inspection should be
made at 3-month intervals. Disconnect the power supply cord, then clean the condenser with a small stiff non-wire brush when required. Observance of this procedure will ensure adequate air circulation through the condenser so operation is efficient and economical.
D. OVERLOAD PROTECTION (water cooler)
The compressor motor, where used, is equipped with an automatic reset protector which will disconnect the motor from the line in
case of an overload.
E. LUBRICATION (water cooler)
This unit is equipped with a hermetically sealed compressor and requires no additional lubrication. The fan motor on this unit seldom
needs oiling, but if required, a few drops of SAE 10 oil should be used.
F. TO DISCONTINUE USE OF WATER COOLER AND WATER FOUNTAIN
1. Close water shut off valve.
2. Provide container to catch water to be drained.
3. Disconnect the water supply line at the water cooler “WATER SUPPLY” tube. Disconnect water cooler “DRAIN/REMOTE COLD
WATER” tube from water fountain “WATER IN” tube. Place container under water cooler “DRAIN/REMOTE COLD WATER” tube,
then push and hold push button on the water cooler until water cooler is completely drained. Place container under water fountain
“WATER IN” tube, then push and hold push button on the water fountain until water fountain is completely drained.
4. Disconnect the power supply cords.
5. Plug both water cooler “DRAIN/REMOTE COLD WATER” tube, and water fountain “WATER IN” tube.
6. ALWAYS DRAIN ALL WATER WHEN FREEZING TEMPERATURES ARE ANTICIPATED AND BEFORE SHIPPING THE WATER COOLER.
*American With Disabilities Act
WARNING: The warranty and the Underwriters’ Laboratory Listing for this machine are automatically voided if this machine is
altered, modified, or combined with any other machine or device. Alteration or modification of this machine may cause serious flooding and/or hazardous electrical shock or fire. EXCEPT AS SET FORTH HEREIN, THE MANUFACTURER MAKES NO OTHER WARRANTY,
GUARANTEE OR AGREEMENT EXPRESSED, IMPLIED OR STATUTORY, INCLUDING ANY IMPLIED WARRANTY OR MERCHANT ABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.
0615
2000102867
2
DRINKING FOUNTAIN ROUGH-IN
For All Universal Split Level KEP( )ACSL-SBF Fountains With
Sports Bottle Filler
Drain Configuration Right Side High
Drain Configuration Right Side Low
WATER FOUNTAIN
RIGHT SIDE PANEL
WATER COOLER
LEFT SIDE PANEL
COOLER SIDE
6" LG. DRAIN
MOVE TO FOUNTAIN SIDE
1 1/2" LG. DRAIN
MOVE TO COOLER SIDE
DRAINS IN FACTORY
INSTALLED POSITIONS
PATCH PLATE LOCATION FOR COOLER
CONVERTED TO RIGHT SIDE LOW
PATCH PLATE LOCATION AS DELIVERED
FOR RIGHT SIDE HIGH
Right Side High As Delivered
DRAIN TUBE
35 1/4 [895]
NOTES:
OPTIONAL GLASSFILLER
LOCATION
SHORT LEG
WATER
FOUNTAIN
1. TRAP, STOP VALVE AND ELECTRICAL
OUTLET NOT FURNISHED.
WATER
COOLER
2. ALLOW 4 INCHES [102 MM] MIN.
PER SIDE FOR VENTILATION.
* 3. RECOMMENDED ADULT BARRIER FREE
HEIGHT INSTALLATION SHOWN. REDUCE
HEIGHT BY 3 INCHES FOR INSTALLATIONS
USED PRIMARILY BY CHILDREN AGES 12
AND YOUNGER. UNIT SHALL ALSO HAVE A
MINIMUM CLEAR FLOOR SPACE 30[760] BY
48[1220]. ADJUST VERTICAL DIMENSIONS
AS REQ’D TO COMPLY WITH FEDERAL,
STATE, AND LOCAL CODES.
18 5/8
[473]
KEPV8ACSL
KEPVF8ACSL
PUSH PAD
WATER COOLER AND FOUNTAIN
3/8 O.D. WATER INLET WITH STRAINER
CONNECT COOLER REMOTE OUTLET TO
FOUNTAIN WATER INLET WITH FITTING SUPPLIED
12 3/4 [324]
2 PLCS.
3 5/16
[84]
AIR
FLOW
14 1/8 [359]
2 PLCS.
1 1/2 [13]2 PLCS.
*33
[838]
ORIFICE
1 1/2 [38]
2 PLCS.
*37 1/32
[941]
1 [25]
*18 1/16
[459]
*17
[432]
15 7/16 [392]
2 PLCS.
4
[102]
25/32 [20]
2 PLCS.
7 [178]
2 PLCS.
1/4 [6] MOUNTING HOLES
8 PLCS.
2000102867
*24 1/16
[611]
*38 3/16
[970]
1 1/4 O.D.
TAILPIECE
*27
[686]
*6 7/32
[158]
*21 1/4
[540]
*13 9/32
[337]
*7 1/16
[179]
ELECTRICAL OUTLET OPTIMUM LOCATION
3/8 WATER SUPPLY OPTIMUM LOCATION STUB OUT 1[25]
RIGHT SIDE HIGH
AS DELIVERED
0615
*35 5/16
[897]
7 23/32 [196]
2 PLCS.
*16 1/2
[419]
18 29/32
[480]
8 1/4
[209]
1/2 [13]
*21 1/4
[540]
6
[152]
2 1/4 [57]
1 1/4 IPS WASTE OPTIMUM
LOCATION STUB OUT 1[25]
*29 5/16
[744]
T15 DRIVE SIZE
TORX HEAD SCREWS
ELECTRONIC EYE MODELS ONLY
5/16 [8] HANGER
MOUNTING HOLES,
4 PLCS.
5 1/4 [133]
KEPF8ACSL(EE) & KEPVF8ACSL
FILTER WITH FLEXIBLE TUBING
4. ALL DIMENSIONS ARE IN INCHES.
DIMENSIONS IN BRACKETS [ ] ARE IN
MILLIMETERS.
17 5/8 [448]
6 3/8 [162]
2 PLCS.
1/4 [6] HANGER
MOUNTING HOLE, 2 PLCS.
PUSH BUTTON
THIRD ANGLE PROJECTION
ROUGHING-IN
AND
DIMENSIONAL DRAWING
3
DRINKING FOUNTAIN INSTALLATION
For All Universal Split Level KEP( )ACSL-SBF Fountains With
Sports Bottle Filler
Right Side Low After Conversion
DRAIN TUBE
35 1/4 [895]
OPTIONAL GLASSFILLER
LOCATION
SHORT LEG
WATER
FOUNTAIN
NOTES:
1. TRAP, STOP VALVE AND ELECTRICAL
OUTLET NOT FURNISHED.
WATER
COOLER
2. ALLOW 4 INCHES [102 MM] MIN.
PER SIDE FOR VENTILATION.
* 3. RECOMMENDED ADULT BARRIER FREE
HEIGHT INSTALLATION SHOWN. REDUCE
HEIGHT BY 3 INCHES FOR INSTALLATIONS
USED PRIMARILY BY CHILDREN AGES 12
AND YOUNGER. UNIT SHALL ALSO HAVE A
MINIMUM CLEAR FLOOR SPACE 30[760] BY
48[1220]. ADJUST VERTICAL DIMENSIONS
AS REQ’D TO COMPLY WITH PROVINCIAL
AND LOCAL CODES.
*18 5/8
[473]
KEPV8ACSL
KEPVF8ACSL
5/16 [8] HANGER MOUNTING
HOLE, 4 PLCS.
17 5/8 [448]
1/4 [6] HANGER MOUNTING
HOLE, 2 PLCS.
12 3/4 [324]
2 PLCS.
1 1/4 IPS WASTE OPTIMUM
LOCATION STUB OUT 1[25]
KEPF8ACSL(EE), KEPVF8ACSL
FILTER WITH FLEXIBLE TUBING
ELECTRONIC EYE MODELS ONLY
1/2 [13]
2 PLCS.
6
[152]
*37 1/32
[941]
14 1/8 [359]
2 PLCS.
18 29/32
[480]
AIR
FLOW
*24 1/16
[611]
*23
[584]
ELECTRICAL OUTLET
OPTIMUM LOCATION
7 23/32 [196]
2 PLCS.
*33 [838]
ORIFICE
1/4 [8] MOUNTING
HOLES, 8 PLCS.
*35 5/16
[897]
25/32 [20]
2 PLCS.
4. ALL DIMENSIONS ARE IN INCHES.
DIMENSIONS IN BRACKETS [ ] ARE IN
MILLIMETERS.
T15 DRIVE SIZE
TORX HEAD SCREWS
6 3/8
[162]
2 PLCS.
3 5/16 [84]
2 1/4 [57]
2 PLCS.
PUSH BUTTON
PUSH PAD
WATER COOLER
AND FOUNTAIN
8 1/4
[209]
2
[51]
1 1/2 [38]
2 PLCS.
1 [25]
2 PLCS.
15 7/16 [392]
2 PLCS.
*21 1/4
[540]
*18 1/16
[459]
*27
[686]
*16 1/2
[419]
1 3/4
[44]
*21 1/4
[540]
6 7/32
[158]
*13 9/32
[337]
5 1/4 [133]
7 1/16
[179]
7 [178]
2 PLCS.
RIGHT SIDE LOW
AFTER CONVERSION
2000102867
1 1/4 O.D.
TAILPIECE
3/8 O.D.
WATER INLET
WITH STRAINER
1/2 [13]
3/8 WATER SUPPLY OPTIMUM
LOCATION STUB OUT 1[25]
0615
*38 3/16
[970]
*29 5/16
[744]
THIRD ANGLE PROJECTION
ROUGHING-IN
AND
DIMENSIONAL DRAWING
4
DRINKING FOUNTAIN INSTALLATION
For All Universal Split Level KEP( )ACSL-SBF Fountains With
Sports Bottle Filler
This bottle filler is an extension of the drinking fountains
product line.
It is mounted directly to an existing unit and no additional
electrical connections are required. If installed into a refrigerated drinking fountain, chilled water can be dispensed through
the bottle filler. Otherwise, room temperature water will be
dispensed.
The bottle filler kit is shipped partially assembled.
WHEN COMPLETED, THE FINISHED ASSEMBLY WILL LOOK LIKE THIS:
Model shown has the Sandstone cabinet finish.
0615
2000102867
5
SECTION 1: GETTING STARTED
NOT PRE-DRILLED/BOTTLE FILLER KIT:
If the unit is not pre-drilled or you purchased a BOTTLE FILLER retrofit KIT,
go to PAGE 7 following.
PRE-DRILLED:
If your unit was purchased pre-drilled at the factory as a COMBINATION, go to PAGE 9.
WHAT’S INCLUDED?
TOOLS REQUIRED:
1. Top cap
2. 38" of 1/4 OD plastic tubing with 19" of sponge tubing insulation
3.Gasket
4. Quick connect tee fitting (only required on split level models)
5. Installation instructions
6. Drip tray
7. Anti splash grate
8. Anti Splash grate screws (2)
9. Snap bushing
10. Wrap-around cabinet facing
11. Hands-free sports bottle filler
- 3/8" drill bit that will drill through stainless steel top
- Electric drill
- Small tubing cutter for copper tube
- T15 Torx driver with pin in head vandal tip
- T20 Torx driver with pin in head vandal tip
- 1/4" nut driver
- #2 Phillips screw driver
6.
2.
1.
7.
3.
4.
8.
10.
5.
9.
11.
0615
2000102867
6
SECTION
3: CONNECTING
INSTALLATION
SECTION 3:
THE WATER LINE
WATER
COOLER
INSTALLATION INSTRUCTIONS, MODELS: KEPWSBF
DRINKING
FOUNTAIN
UNITS NOT PRE-DRILLED ONLY
A. DRILLING HOLE IN THE TOP FOR WATER LINE CONNECTION
1. Disconnect power by UNPLUGGING unit. It might be necessary to remove the front panel to get access to the power.
2. Turn OFF water supply to the unit. It might be necessary to remove the front panel to access the water stop valve.
3. Place hole template onto cooler top so it is aligned with the left side of unit and wall. (TEMPLATE FOUND ON PAGE 17)
STEP 1:
4. Mark hole location.
a) Disconnect power by UNPLUGGING unit. It might be necessary to remove the front panel to get access to the power.
5. Remove
unit.
(Figure
1) unit. It might be necessary to remove the front panel to access the water stop valve.
b) Turn top
OFFfrom
water
supply
to the
6. Using
a 3/8
drill
bit, drillonto
a hole
through
top.it is aligned with the left side of unit and wall. SEE NEXT PAGE FOR TEMPLATE.
c) Place
hole
template
cooler
top so
d) Mark
hole
location.
7. Install
snap
bushing
into hole to protect tubing from being cut. (Figure 2)
Template
Figure 2
Figure 1
Mark hole location
Drill
Install Bushing
Remove top from cooler by
removing six #15 torx head
screws on sides of top.
e) Remove top from unit. (Figure 1)
B. CONNECTING
THE
f) Using a 3/8 drill
bit, WATER
drill a holeLINE
through top.
If the cooling tank is non-pressurized, then go to the "Pressurizing the cooling tank" addendum section. Otherwise, proceed to
g) Install snap bushing into hole to protect tubing from being cut. (Figure 2)
STEP 1 next page. Non-pressurized units are single units made since December of 2009. Refer to the schematic below to identify
the system that you have.
Water
valve/regulator
NON-PRESSURIZED
COOLING TANK
0615
2000102867
Supply
Water
Cooling
tank
Supply
Water
Cooling
tank
Water
valve/regulator
PRESSURIZED
COOLING TANK
7
ALIGN DASHED EDGE WITH LEFT EDGE OF COOLER TOP
2 1/8"
[5.4 cm]
FROM BACK
Mark this center point on the.
top. Remove the top from the
cooler. Then drill a 3/8" [9.5mm] hole
through the top at the marked
center point.
PLACE THIS DASHED EDGE AGAINST WALL
3 1/4"
[8.25 cm]
FROM SIDE
UNITS NOT PRE-DRILLED ONLY
USE THIS TEMPLATE TO MARK THE HOLE
LOCATION ON COOLER TOP
0615
2000102867
8
SECTION 3: CONNECTING THE WATER LINE
DRINKING FOUNTAIN
STEP 2:
With the cooler top removed, find the tube going from the cooling tank outlet to the valve. The TEE fitting (supplied) will need to connect between the cooling tank and valve. (Figure 3)
STEP 3:
Outlet Tube (insulated plastic)
Figure 3
VALVE
KEP8AC FAMILY
Disconnect tubing from the elbow on the valve. (Figure 4)
STEP 4:
Using the 30" piece of tubing provided, cut 6" and install it on the end of the TEE. Install the remaining tubing onto the branch of the TEE.
Connect the other end of the TEE to the tank outlet tubing (tube that was disconnected from the elbow). (Figure 5)
STEP 5:
Route the TEE and tubing under the waste drain and connect the 6" length to the water valve elbow. (Figure 6)
24" TUBING
TEE
Figure 4
0615
2000102867
6" TUBING
Figure 5
WATER
VALVE
ELBOW
Figure 6
9
SECTION 3: CONNECTING THE WATER LINE (cont'd)
DRINKING FOUNTAIN
STEP
ÉTAPE6:6
Faire passer
dansthe
le dessus
et attach
fixer ce the
dernier
(Figure 7)
10)
Feed
tubingleuptuyau
through
top and
top au
to refroidisseur.
the cooler. (Figure
Figure 7
0615
2000102867
10
SECTION 4: MOUNTING THE FRAME TO THE WALL
STEP 1:
Place rubber gasket on top of the cooler so it is centered left/right and against the wall. (Figure 11)
STEP 2:
Set the wall frame onto the gasket. Center it left/right and push it against the wall and mark hole locations for wall fasteners. The gasket will
set the frame at the proper height. (Figure 12)
STEP 3:
Secure frame to the wall with fasteners (not provided). Pull plastic tubing up through the hole in the frame. Use mounting slots that will provide
the proper securing location. Make sure to pull the plastic tubing up through the hole in the frame.
Figure 11
Make sure to pull
the plastic tubing
up through the
hole in the frame.
STEP 4:
Figure 12
Use mounting
slots that will
provide the proper
securing location.
Figure 13
Slide sponge tubing insulation over water line.
Connect the tubing to the INLET elbow on the
back of the bottle filler assembly. (Figure 13)
Connect tube to elbow
on the valve
Plastic tubing
Sponge tubing insulation
REAR VIEW OF BOTTLE FILLER
STEP 5:
Set the bottle filler
cabinet into place.
MAKE SURE the cabinet
fits into the groove in
the rubber gasket on
both sides and front of
the cabinet wrapper.
(Figure 14)
0615
2000102867
Figure 14
Bottle filler cabinet
Groove in the gasket
11
SECTION 4: MOUNTING THE FRAME TO THE WALL (continuation)
STEP 6:
Attach Bottle Filler assembly and top cap to the frame using the six (6) vandal resistant torx screws. (Figure 15)
Figure 15
Torx screws
STEP 7:
Install the drip tray and anti-splash grate into the alcove area and secure with the two (2) stainless steel Phillips head screws. (Figure 16)
STEP 8:
Turn ON water supply and check for leaks. Press the activation button and release any trapped air from the system. Plug in the power cord and
replace the front panel IF it was removed earlier. (Figure 17)
Figure 16
Figure 17
Anti-splash
grate screws
(provided)
Press
Anti-splash
grate
Drip tray
INSTALLATION COMPLETE
0615
2000102867
12
EXPLODED PARTS BREAKDOWN
SPORTS BOTTLE FILLER
25
33
26
12
13
29
19
24
16
14
3
17
15
28
2
27
18
1
32
20
9
22
30
21
8
23
4
6
22
22
11
25
10
5
31
7
22
0615
2000102867
13
EXPLODED VIEW LIST OF PARTS
SPORTS BOTTLE FILLER
1. 036190-002 2. 036691-001 3. 036686-001 4. 036049-002
5. 036688-001 6. 036695-001 7. 036697-001 8. 036194-002 9. 034649-001 10.036689-001 11.036191-002 12.035990-001 13.029967-002 14.A020957
15.036690-001 16.030176-002 17.028706-036 18. 026670-007 19. 028481-101 20. 036209-001 21.026642-003 22. 026642-003 23.031206-005 24.030152-046 25.031875-003
26.036687-001 27.027189-007 28.029199-103 29.030152-031 30.017681-008 31.036701-001 32.036702-001 33.036231-001-SP
Alcove
Wrapper
Cap
Screw, flat head tapping
Tray, drip
Tray, grille drip
Bottom cap for drip tray
Button
Spring
Gasket
Drain, short
Holder, cartridge stem connector
Cartridge
Nut, retaining plastic
Bracket, valve
Plug, hole
Washer/spacer/gasket-non metallic
Screw, hex heavy duty machine
Fitting, PP union elbow white
Fill tube assembly
Bracket, fill tube support
Screw, hex heavy duty tapping
Insert, nameplate “Aquapointe”
Tube, PE cut length white
Screw, button heavy duty tapping
Frame
Bushing, snap
Fitting, PP untion tee white
Tube, PE cut length white
Insulation, sponge tubing
Drip tray assembly, service
Button assembly, service
Valve assembly, dispense-service
Accessory Kits
036704-001 SRH-KEPWSBF
EKG-KEPWSBF Vandal resistant screw kit - Includes torx bits and replacement screws for items 4, and 25
Gasket, Sunroc/Haws #036689-101 - Replaces item 10
Gasket, Elkay/Halsey Taylor #036689-201 - Replaces item 10
Haws is a registered trademark of HAWS Corporation.
Elkay and Halsey Taylor are registered trademarks owned or licensed by Elkay Sales Inc. and/or its parent Elkay Manufacturing Company.
0615
2000102867
14
SPECIFICATIONS
CHILLED DRINKING FOUNTAIN
Voltage
Size
Shipping Weight (Approx)
Cold Water Capacity
Compressor
Compressor (Full Load)
Refrigerant
Refrigerant Charge
Room Temperature
Supply Water Temperature Drinking Water Temperature
MODELS: SPLIT LEVEL UNIVERSAL
MODELS: SINGLE UNIVERSAL
115 VAC±10%/1 PH/60 Hertz
35 1/4" W, 18 5/8" D, 24 29/32" H
84 lbs.
8 GPH
1/4 hp
4.4 amps
134a
3.95 OZ
90◦F
80◦F
50◦F
115 VAC±10%/1 PH/60 Hertz
17 5/8" W, 18 5/8" D, 18 29/32" H
59 lbs.
8 GPH
1/4 hp
4.4 amps
134a
3.95 OZ
90◦F
80◦F
50◦F
Specifications subject to change
without notice.
0615
2000102867
15
EXPLODED PARTS BREAKDOWN
DRINKING FOUNTAIN
To adjust stream height, insert a 1/8" flat blade screwdriver into
the slotted hole as shown. The screwdriver will engage the stream
height adjuster in the cartridge plunger. Turn clockwise to increase
stream height or counter clockwise to reduce stream height.
0615
2000102867
16
PARTS BREAKDOWN LIST
DRINKING FOUNTAIN
Item
Single
Split Level
Single
#Description...............................................................Chilled.......................Chilled....................... Non-chilled
1.Top............................................................................ 031714-101...............031714-101............... 031714-101
2.Bubbler..................................................................... 035607-108...............103607-108............... 035607-108
3. Washer, under top..................................................... 028706-030...............028706-030............... 028706-030
4.Locknut..................................................................... 026824-019...............026824-019............... 026824--109
5. Bubbler nut W/ JG (John Guest)................................ 036026-001...............036026-001............... 036026-001
6.Condenser................................................................ 031766-201...............031766-201............... Not applicable
7. Side panel, Left – Sandstone .................................... 035080-009...............035080-309............... 035080-009
Side panel, Left – Greystone .................................... 035080-001...............035080-301............... 035080-001
Side panel, Left – Stainless Steel.............................. 035080-010...............035080-310............... 035080-010
8. Blade, fan.................................................................. 024033......................024033...................... Not applicable
9. Motor, fan................................................................. 027354-036...............027354-036............... Not applicable
10. Bracket, fan motor.................................................... 036478-001...............036478-001............... Not applicable
11. Drain screw............................................................... 036049-002...............036049-002............... 036049-002
12. Waste gasket............................................................. 031756-002...............031756-002............... 031756-002
13. Hanger bracket......................................................... 031363-002...............031363-002............... 031363-002
14. Side panel, Right - Sandstone.................................... 035081-009...............035081-009............... 035081-309
Side panel, Right - Greystone.................................... 035081-001...............035081-001............... 035081-301
Side panel, Right - Stainless Steel............................. 035081-010...............035081-010............... 035081-310
15. Patch plate - Sandstone............................................ Not applicable............036142-009............... 036142-009
Patch plate - Greystone............................................. Not applicable............031642-001............... 031642-001
Patch plate - Stainless Steel...................................... Not applicable............031642-010............... 031642-010
16. Service cord.............................................................. 026540-045...............026540-045............... Not applicable
17.Frame....................................................................... 035089-001...............035089-001............... 035089-001
18. Waste assembly........................................................ 036011-001...............036011-002............... 036009-002
19. Insulation, right cooling tank..................................... 035088-001...............035088-001............... Not applicable
20. Insulation, left cooling tank....................................... 035088-002...............035088-002............... Not applicable
21. Cooling tank, insulated.............................................. 035469-055-SP..........035469-055-SP.......... Not applicable
22. Cold control.............................................................. 027040-039...............027040-039............... Not applicable
23.Relay......................................................................... 036056-003...............036056-003............... Not applicable
24.Overload................................................................... 036055-003...............036055-003............... Not applicable
25. Start capacitor — 60 MFD......................................... 027956-008...............027956-008............... Not applicable
26. Run capacitor —25 MFD............................................ 027956-009...............027956-009............... Not applicable
27. Compressor assembly............................................... 036115-001...............036115-001............... Not applicable
28. Front panel, Right - Sandstone.................................. 035079-009...............035079-009............... 035079-009
Front panel, Right - Greystone................................... 035079-001...............035079--001.............. 035079--001
Front panel, Right - Stainless Steel............................ 035079-010...............035079-010............... 035079-010
29. Front nose piece - Sandstone.................................... 035077-009...............035077-009............... 035077-009
Front nose piece - Greystone.................................... 035077-001...............035077-001............... 035077-001
Front nose piece - Stainless Steel............................. 035077-010...............035077-010............... 035077-010
30. Activation assembly.................................................. 035412-004...............035412-004............... 035412-004
31. Water line, tank to valve............................................ 035504-011-SP..........035504-011-SP.......... 035503-001
Water line, inlet to valve or tank................................. 035504-010-SP..........035504-010-SP.......... Not applicable
32. Union elbow fitting JG (John Guest)............................ 02481-101.................028481-101............... 028481-101
33. Cartridge holder........................................................ 035990-00.................035990-001............... 035990-001
34.Cartridge................................................................... 029967-002...............029967-002............... 029967-002
35. Retaining nut, cartridge............................................. A020957....................A020957.................... A020957
36. Water line, tank or valve to bubbler............................ 035504-013-SP..........035504-013-SP.......... 035504-013-SP
37.Shelf......................................................................... 035078-002...............035078-002............... 035078-002
38.Dryer......................................................................... 034343-003...............034343-003............... Not applicable
39. Activation shelf......................................................... 035092M101.............035092M101............. 035092M101
40. Waste tee.................................................................. Not applicable............A020968.................... A020968
41. Waste arm assembly................................................. Not applicable............026980-004............... 0269980-004
42. Waste elbow.............................................................. Not applicable............A020967.................... A020967
43. Waste extension tube................................................ Not applicable............036010-016............... 036010-016
Parts Not Shown:
Strainer, in-line.......................................................... 033264-003...............033264-003............... 033264-003
0615
2000102867
17
WIRING DIAGRAM
DRINKING FOUNTAIN
WIRING DIAGRAM
Single KEP(_)
KEP(__)Series
series,
Single
Split Level KEP (__) series
Split Level KEP(_)ACSL Series
Franke Kindred Canada Limited
Franke Commercial Systems
1000 Franke Kindred Road
Midland, ON L4R 4K9
Tel 1.855.446.5663
Fax 1.866.227.3050
www.franke-commercial.com
0615
2000102867