- Wireless Security Cameras

WAC020
2
GSM MMS Camera Alarm System
http://www.securitywireless.co.za
User Manual
Ver 1.0
Date Issued: 2015-07-01
All rights reserved.
GSM MMS Camera Alarm System
Table of contents
1. Product details --------------------------------------------------------------------------------3
2. Safety Directions --------------------------------------------------------------------------4
3. Wiring Connection --------------------------------------------------------------------------5
4. How WAC02 works for you?----------------------------------------------------------------6
5. SMS Command-------------------------------------------------------------------------------7
5.1 Common operate commands-----------------------------------------------------------------------------------7
5.26LUHQDQGFDPHUD¶VPRWLRQdetector---------------------------------------------------------------------------7
5.3 $ODUPUHFHLYHU¶V3KRQHQXPEHU--------------------------------------------------------------------------------7
5.4 Edit DIN1~DIN8 zone name----------------------------------------------------------------------------------7
5.5 ',1a',1VHQVRU¶VW\SH----------------------------------------------------------------------------------------8
5.6 GPRS MMS parameters-----------------------------------------------------------------------------------------8
5.7 Email address-------------------------------------------------------------------------------------------------------8
5.8 Camera parameters-----------------------------------------------------------------------------------------------8
5.9 Other Settings-----------------------------------------------------------------------------------------------------9
6. Warranty --------------------------------------------------------------------------------9
This handbook has been designed as a guide to the installation and operation of WAC02 Alarm Panel.
Statements contained in the handbook are general guidelines only and in no way are designed to supersede the
instructions contained with other products.
We recommend that the advice of a registered electrician be sought before any Installation work commences.
The manufacturer, its employees and distributors, accept no liability for any loss or damage including
consequential damage due to reliance on any material contained in this handbook.
The manufacturer, its employees and distributors, accept no liability for GSM Network upgrading or SIM Card
upgrading due to the technology specifications contained in this handbook.
Page 2 of 9 Ver 1.0
GSM MMS Camera Alarm System
1. Product details
The WAC02 GSM MMS Camera Alarm Controller is designed for taking on site photos and remote switching on/off machines
and equipment by SMS command. 8 channel digital inputs for different kinds of detectors like water leakage detector, door
contact sensors and so on. The camera include IR lights and motion detector. When alarm or motion is detected, WAC02 will send a
photo by MMS and alert with SMS to user. User can also add 2 e-mails for receiving pictures from WAC02.
ARM/DISARM button, arm and alarm delay, on site voice monitoring functions, you can install the WAC02 MMS Camera
Alarm controller for a lot of applications.
Smart phone APP available for easy configuration and operation.
Features:
z
z
z
z
z
z
z
GSM Quad-Band 850/900/1800/1900 MHz
External weather-proof camera with IR lights and motion detector
3 sizes for MMS Photo resolution optional
8 Digital input, alarm SMS text editable
1 Relay output can be switched on/off by SMS Commands
1 Siren output for warning while alarm occur
z
5 telephone numbers can be setup as dial or receive alarm SMS,MMS message
2 e-mails for receiving photos
z
z
Arm or disarmed by SMS commands or wired button
AC power lost and recovery alarm SMS.
z
Internal backup rechargeable battery with low power alarm buzzer
Applications:
z
z
z
Home intrusion security and surveillance alarm system
Warehouse, Factory, Office, Business, Summer house, ATM station security and surveillance alarm system.
Unmanned Station, Reservoir, Tower, Pump, Motor, Water Supply, BTS, Remote Area monitoring and surveillance alarm
system.
Specification and dimensions
GSM Frequency
Camera
Digital Input
Digital Output
Siren Output
Quad-band 850/900/1800/1900MHz
External outdoor water-proof
8 NC/NO dry contact
1 Relay, 3A/240VAC
12VDC/1A
DC Power supply
9~24VDC/2A
Back up battery
7.4V/1000mAH
Power consumption
12V input Max. 50mA/Average 25mA
SIM Card
Supporting 3V SIM Card
Antenna
ϱϬɏ^DŶƚĞŶŶĂŝŶƚĞƌĨĂĐĞ
Temperature range
Humidity range
-20~+60 °C
Relative humidity 90%
Page 3 of 9 Ver 1.0
GSM MMS Camera Alarm System
Standard Packing List
9
9
9
9
9
WAC02 GSM Main Unit *1
External Camera *1
Antenna * 1
AC/DC Power adaptor *1,
User Manual CD x1
Optional Accessories:
9
9
9
9
9
9
PIR Motion Sensor,
Door Magnetic contact Sensor,
Smoke detector
Gas leakage detector
Water flood sensor
Water Level sensor
2.Safety Directions
Safe Startup
Do not use WAC02 where using GSM equipment is prohibited or might cause disturbance or danger.
Interference
Other wireless equipment might interfere with network signals of WAC02 and influence its performance.
Avoid Gas Station
Do not use WAC02 at a gas station. Switch off WAC02 when it is near fuels or chemicals.
Power off near Blasting Places
Please follow relevant restrictive regulations. Avoid using the device in blasting areas.
Reasonable Use
Please install the product at suitable places as described in the product documentation. Avoid signal
shieldeding by covering the mainframe.
Use Qualified Maintenance Service
Maintenance can be carried out only by qualified maintainer. Do not
break warrantee seals.
Page 4 of 9 Ver 1.0
GSM MMS Camera Alarm System
3. Wiring Connection
LED INDICATORS
Arm
Relay
Camera
I
III
Flash : Armed
Always Light ON: Disarm.
ON: Relay closed(ON)
OFF: Relay open (OFF)
ON: Camera disconnected or wrong connection.
OFF: Camera on correct status.
Flash quickly: registering to cellular network.
Flash slowly: alarm or GPRS data communication.
OFF: registered to cellular network success.
Main Connection Terminals
Camera
TxD
Data Transmitting (Blue)
RxD
Data Receiving (Yellow)
5V
Vdd (Black)
6V
Power supply (Red)
GND
Arm
Siren
Relay
Power In
Shielded wire
A+
Connect one NC/NO button or switch on A+ and GND port, press the button to
enter to Arm status, repress the button to Disarm.
S+
ϭϮsнŽƵƚƉƵƚ͕ĐŽŶŶĞĐƚƚŽƐŝƌĞŶ͛ƐWŽƐŝƚŝǀĞǁŝƌĞ͘
S--
GND, connect ƚŽƐŝƌĞŶ͛ƐEĞŐĂƚŝǀĞǁŝƌĞ͘
NO
Normally Open port
COM
Common port
+
Power supply input, Positive wire(Red).
_
Power supply input, Negative wire(Black).
Digital Input Zones
12V+
Digital Input
GND
DIN1~DIN8
ANT
DC12V+ power supply for sensors.
Caution: Do not short circuit wire the DC12V+ to DIN1~8 inputs.
DC12V-- power supply for sensors.
DIN1~DIN4 GND
Digital Input, NC/NO dry contact(Voltage free) connection only!
Connect GSM antenna.
Page 5 of 9 Ver 1.0
GSM MMS Camera Alarm System
4. How can WAC02 work for you?
z Start
¾
Insert mobile SIM card(GSM850/900/1800/1900MHz) in the SIM Card slot.
¾
Connect the wiring of the camera and other digital sensors (if have) to the main unit.
¾
Connect the power supply, Switch ON.
¾
If you had programmed your phone number on WAC02, it will send a status SMS to your phone once switched ON.
z Arm & Disarm
¾
(Recommend) Connect one button on the ARM (A+ and GND) port, you can press the button, after a 20 seconds
delay the system will enter Arm status and make 3 confirming beeps. You can also repress it for Disarm.
¾
The DIN8 zone is for entrance purposes, when the sensor on DIN8 zone is triggered, it will delay 15 seconds alarm,
so you have 15 seconds to Disarm the system before alarming.
¾ You can also use APP of send SMS command to Arm/Disarm the system.
z Alarm
¾
When alarm raised, WAC02 sends alert SMS and MMS picture to your phone and make a siren sound, you can
Answer the phone call to listen in on onsite voices or sounds.
¾
zŽƵĐĂŶĞĚŝƚƚŚĞ/EϭΕϴ͛ƐnjŽŶĞŶĂŵĞ͕ƐŽLJŽƵ willƌĞĐĞŝǀĞƚŚĞcontent ^D^
^ŵŽŬĞĂůĂƌŵ ͊͟Žƌ
͞tĂƚĞƌĂůĂƌŵ ͊͘͟ Backdoor open or camera zone entered.
z Remote Control
¾
You can use APP or send SMS commands to switch ON/OFF the relay. To open the gate
etc.
z Inquiry Photos
¾
You can use APP or send SMS commands to ask WAC02 to send back 1~20 photos to your mobile phone. Check if
your dog food is fine. Measure your dam and see water levels. Protect and monitor any property.
z Power Monitoring
¾
You will receive alert SMS when AC/DC power failed and when it recovers. When the back up battery power low,
WAC02 will start alarming beeps to remind the user of such low power.
Page 6 of 9 Ver 1.0
GSM MMS Camera Alarm System
5. SMS Command
¾
¾
WAC02 can be set by smart phone APP or SMS commands with password protection remotely.
The SMS commands should start with the Password. 1234 is the default password. Change to
a new password if you have not changed it already.
¾
¾
WAC02 will not return any message if the SMS command is not correct.
No spaces in the SMS commands, the spaces on the command list is for reading purpose only.
SMS Command
Function
Feedback SMS
Common Operate Commands
1234#00#
Inquire status
1234#01#
Disarm
1234#02#
Arm
1234#03#
Switch Relay OFF
Relay: Off/On
1234#04#
Switch Relay ON
Siren: Off/On
1234#05#
Switch Siren OFF
1234#06#
Switch Siren ON
Status: Armed/Disarmed
^ŝƌĞŶĂŶĚĐĂŵĞƌĂ͛ƐŵŽƚŝŽŶĚĞƚĞĐƚŽƌ
1234#10#
Inquire settings
1234#11#
Siren ON when alarm occur
1234#12#
Siren OFF when alarm occur
1234#16#
ŶĂďůĞĐĂŵĞƌĂ͛ƐŵŽƚŝŽŶĚĞƚĞĐƚŽƌĂůĂƌŵ;ĚĞĨĂƵůƚͿ
1234#15#
ŝƐĂďůĞĐĂŵĞƌĂ͛ƐŵŽƚŝŽŶĚĞƚĞĐƚŽƌĂůĂƌŵ;ĚĞĨĂƵůƚͿ
Siren: ON/OFF
Motion Alarm: On/Off
Alarm Receivers phone number
1234#20##
1234#21#*#
1234#22#*#
1234#23#*#
1234#24#*#
1234#25#*#
/ŶƋƵŝƌe ƌĞĐĞŝǀĞƌ͛ƐƉŚŽŶĞŶƵŵďĞƌ
TEL1:*******
st
Add the 1 ƌĞĐĞŝǀĞƌ͛ƐƉŚŽŶĞŶƵŵďĞƌ
Add the 2nd ƌĞĐĞŝǀĞƌ͛ƐƉŚŽŶĞŶƵŵďĞƌ
rd
TEL2:*******
TEL3:*******
Add the 3 ƌĞĐĞŝǀĞƌ͛ƐƉŚŽŶĞŶƵŵďĞƌ
TEL4:*******
Add the 4 ƌĞĐĞŝǀĞƌ͛ƐƉŚŽŶĞŶƵŵďĞƌ
TEL5:*******
th
th
Add the 5 ƌĞĐĞŝǀĞƌ͛ƐƉŚŽŶĞŶƵŵďĞƌ
Edit DIN1~DIN8 Zone name
1234#30#*#
1234#31#*#
Inquire DIN Zone name
DIN1:*****
*=1~8
DIN2:*****
Edit DIN1 Zone name
DIN3:*****
Page 7 of 9 Ver 1.0
GSM MMS Camera Alarm System
1234#32#*#
Edit DIN2 Zone name
DIN4:*****
1234#33#*#
Edit DIN3 Zone name
DIN5:*****
1234#34#*#
Edit DIN4 Zone name
DIN6:*****
1234#35#*#
Edit DIN5 Zone name
DIN7:*****
1234#36#*#
Edit DIN6 Zone name
DIN8:*****
1234#37#*#
Edit DIN7 Zone name
1234#38#*#
Edit DIN8 Zone name
*= Zone name, max.14 characters.
Default Alarm SMS content: DIN(1~8) Alarm!
DIN1~8 ^ĞŶƐŽƌ͛Ɛ Type
1234#7*#0#
Setting the DIN* type as NO
NO
1234#7*#1#
Setting the DIN* type as NC
NC
*=1~8.
NC=Normally Close, NO=Normally Open.
Default type: NC.
GPRS MMS Parameters
1234#40##
Inquiry MMS settings
Format:
1234#41#*#
Setting GPRS APN(Access Point Name)
APN:******
1234#42#*#
Setting GPRS User Name
User:*******
1234#43#*#
Setting GPRS Password
Pass:******
1234#44#*#
Setting MMSC IP address
IP:******
1234#45#*#
Setting MMSC Port
Port:****
1234#46#*#
Setting MMSC URL
MMSC Url:******
Notice: please call your mobile operator to ask the GPRS Access Point Name, User name, Password, MMSC IP, MMSC
Port and MMSC URL. If there is no User name or Password, etc needed for the GPRS connection, then leave it blank)
For example:
1234#41#everywhere#
1234#42#eesecure#
1234#43#secure#
the example APN name(everywhere), User name(eescure) Password(secure) supported by Orange UK.
E-mail address
1234#50##
1234#51#email address#
1234#51##
1234#52#email address#
1234#52##
Inquiry e-mail address
Email:********
st
Setting the 1 e-mail address
Email 1:****
st
Delete the 1 e-mail address
Setting the 2nd e-mail address
nd
Delete the 2 e-mail address
Page 8 of 9 Ver 1.0
Email 2:****
GSM MMS Camera Alarm System
Camera Parameters
1234#60##
Inquire settings
^ĞƚƚŝŶŐƉŚŽƚŽ͛ƐƌĞƐŽůƵƚŝŽŶ˖
*=0~2
1234#61#*#
0 =160X128;
1 = 320X240
1234#62#*#
2 = 640X480 (default)
Image Size:640*480
Setting how many photos send out when alarm.
Image Qty:1
*=0~20
CamSensitivity:15
Default=1
ĚũƵƐƚĐĂŵĞƌĂ͛ƐŵŽƚŝŽŶĚĞƚĞĐƚŽƌsensitivity
1234#63#*#
*=1~99
1 = the highest sensitive.
Default= 15
Other Settings
1234#90#*#
1234#99#*#
1234#EN#
Inquiry the last photos
*=1~20
Require Image Ok
Change password
*= 4 digits
PASS: 1234
Change language to English, password reset to 1234.
Language: English
When AC/DC power goes off
External AC Power Failure!
Control Panel AC Power
When AC/DC power goes on
Recovery!
6. Warranty
1) This system is warranted to be free of defects in material and workmanship for one year.
2) This warranty does not extend to any defect, malfunction or failure caused by abuse or misuse by the Operating
Instructions. In no event shall the manufacturer be liable for any alarm system altered by purchasers.
www.securitywireless.co.za
Page 9 of 9 Ver 1.0