Akron Hardware Product Catalog Version 3.0
Transcription
Akron Hardware Product Catalog Version 3.0
ADAMS RITE ADAMS RITE ADAMS RITE Visit us on the web at www.akronhardware.com ADAMS RITE 1-800-321-9602 Fax 1-800-328-6070 2 7100 Flat Faceplate for Aluminum Jambs 7101 Radiused Faceplate for Aluminum Stiles ADAMS RITE For Adams Rite or Cylindrical Latches. Remote electrical control of any door equipped with an Adams Rite Series 4500 or 4700 (or similar) deadlatch or “key-in-knob” sets. Electrical actuation unlocks strike jaw, releasing latchbolt so door can be opened without operating latch itself. Extremely compact mechanism fits into aluminum jamb (or opposing door) sections as shallow as 1-5/8”. Fits prep for 7500/7800/7000 Series. Features Include: • Case: Approx. 1” x 3-3/8” x 1-5/8” deep. Zinc-aluminum alloy. • Strike Lip: Basic 7100 strike has lip of proper length for 1-3/4” thick door that closes flush with jamb edge. • Fail Safe/Fail Secure: Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. • Strike Opening: 5/8” x 1-7/16” x 1/2” deep. • Faceplate: Measures 1-1/4” x 4-7/8”. 7100 has flat faceplate; 7101 is radiused. Technical Specifications: UL ® UL Listed for Burglary Resistance VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • Case: Approx. 1” x 3-3/8” x 1-5/8” deep. Zinc-aluminum alloy. • Strike Lip: Basic Basic 7130 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge. • Fail Safe/Fail Secure: Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. • Strike Opening: 5/8" x 1-7/16" x 1/2" deep. • Faceplate: Measures 1-1/4" x 6-7/8". 7130 has flat faceplate, 7131 is radiused. Technical Specifications: UL ® UL Listed for Burglary Resistance VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Visit us on the web at www.akronhardware.com ADAMS RITE For Adams Rite or Cylindrical Latches. Remote electrical control of any narrow stile or hollow metal door equipped with an Adams Rite Series 4500 or 4700 (or similar) deadlatch. Large faceplate is designed to cover strike opening when converting from an MS pivotedbolt deadlock to a deadlatch. Electrical actuation unlocks strike jaw, releasing latchbolt so door can be opened without operating latch itself. Extremely compact mechanism fits into aluminum jamb (or opposing door) sections as shallow as 1-5/8". Fits prep for 7530/7830 Series. 3 7130 Flat Faceplate for Aluminum Jambs 7131 Radiused Faceplate for Aluminum Stiles 4 Electric Strikes - 7110 / 7111 Mounts In Wood or Hollow Steel Jambs ADAMS RITE For Adams Rite or Cylindrical Latches. Replaces earlier 002, 7510 or 7810 electric releases in either metal or wooden jambs for remote electrical control of any door equipped with cylindrical latchset or Adams Rite Series 4500 or 4700 (or similar) deadlatch. Electrical actuation unlocks strike jaw, releasing latchbolt so door can be opened without operating latch itself. Extremely compact mechanism fits into jamb sections as shallow as 1-5/8". Features Include: • Case: Approx. 1" x 3-3/8" x 1-5/8" deep. Zinc-aluminum alloy. • Strike Lip: Basic 7110 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge. • Fail Safe/Fail Secure: Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. • Strike Opening: 5/8” x 1-7/16” x 1/2” deep. • Faceplate: 7110 measures 1-7/16" x 7-15/16". Technical Specifications: UL ® UL Listed for Burglary Resistance VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • Case: Approx. 1" x 3-3/8" x 1-5/8" deep. Made of Zinc-aluminum alloy. • Strike Lip: Basic 7140 strikes have lip of proper length for 1-3/4" thick door that closes flush with jamb edge. • Fail Safe/Fail Secure: Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. • Strike Opening: 5/8" x 1-7/16" x 1/2" deep. • Faceplate: Measures 1-1/4" x 4-7/8". Faceplate is flat, with square corners. Technical Specifications: UL ® UL Listed for Burglary Resistance VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Visit us on the web at www.akronhardware.com ADAMS RITE For Key-in-Knob or Adams Rite Latches. Remote electrical control of any door equipped with cylindrical (key-in-knob/lever) type latchsets listed above. Electrical actuation unlocks strike jaw, releasing latchbolt , so door can be opened without operating latch itself. Extremely compact mechanism fits into jamb sections as shallow as 1-5/8". Fits existing preps for 7840AN and 7850/7040. 5 Electric Strikes - 7140 Mounts In Wood or Hollow Steel Jambs and Doors 6 7160 - Electric Strikes Mounts in Aluminum Jambs ADAMS RITE For Mortise Latches without Deadbolt By Others. Remote electrical control of any door equipped with a mortise type latchsets. Electrical actuation unlocks strike jaw, releasing latchbolt so door can be opened without operating latch itself. Extremely compact mechanism fits into hollow jamb sections as shallow as 1-7/8". Fits prep for 7560/7860. Features Include: • Case: Approx. 1" x 3-3/8" x 1-7/8" deep. Zinc-aluminum alloy. • Strike Lip: Basic 7160 strikes have lip of proper length for 1-3/4" thick door that closes flush with jamb edge. • Fail Safe/Fail Secure: Field convertible from one mode to the other. However AC intermittent solenoid must not be used continuously in either. • Strike Opening: 3/4" x 1-7/16" x 5/8” deep. • Faceplate: Measures 1-1/4" x 4-7/8". Faceplate is flat, with radiused corners. Technical Specifications: UL Listed for Burglary Resistance UL ® VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • Case: Approx: Approx. 1" x 3-3/8" x 1-7/8” deep. Made of Zinc-aluminum alloy. • Strike Lip: Basic 7170 strikes have lip of proper length for 1-3/4" thick door that closes flush with jamb edge. • Fail Safe/Fail Secure: Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. • Strike Opening: 5/8" x 1-7/16" x 5/8” deep. • Faceplate: Measures 1-1/4" x 4-7/8". Faceplate is flat, with square corners. Technical Specifications: UL ® UL Listed for Burglary Resistance VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Visit us on the web at www.akronhardware.com ADAMS RITE For Mortise Latches without Deadbolt By Others. Remote electrical control of any door equipped with a Mortise Type latchsets. Electrical actuation unlocks strike jaw, releasing latchbolt so door can be opened without operating latch itself. Extremely compact mechanism fits hollow jamb sections as shallow as 1-7/8". Fits prep for 7560AN/7860AN and 7570/7870. 7 7170 - Electric Strikes Mounts in Wood or Hollow Steel Jambs For Pullman Bolt Rim Exit Devices. A semi-mortised strike for Rim exit devices having Pullman type bolts. Provides electrical remote control allowing door to open without actuation of the exit device. ADAMS RITE 8 71R1 - Electric Strikes Mounts in Aluminum, Wood or Hollow Steel Jambs Features Include: • Case: Approx. 1" x 3-3/8" x 7/8" deep. Made of zinc-aluminum alloy. • Fail Safe/Fail Secure: Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. • Strike Opening: 5/8" x 1-7/16" x 9/16" deep. • Mounting Plate/Housing: Measures 1-3/4" x 9" x 3/4" deep. Technical Specifications: UL ® UL Listed for Burglary Resistance VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • Case: Approx. 1" x 3-3/8" x 1-1/8" deep. Made of zinc-aluminum alloy. • Fail Safe/Fail Secure: Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. • Strike Opening: 5/8" x 1-7/16" x 1/2" deep. • Mounting Plate: Measures 1-1/2" x 9" x 1/2" deep. Technical Specifications: UL ® UL Listed for Burglary Resistance VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Call our Sales department - toll free - for current pricing on all Adams Rite products Visit us on the web at www.akronhardware.com ADAMS RITE For Narrow Stile Rim Exit Devices with 1/2” bolt. A semi-mortised strike for Rim exit devices having 1/2" Pullman type bolts without auxiliary bolts. Provides electrical remote control allowing door to open without actuation of the exit device. 9 71R2 - Electric Strikes Mounts in Aluminum Jambs 10 7240 / Fire Rated in Fail-Secure Mode For Hollow Steel Jambs ADAMS RITE For Key-in-Knob Latches. Remote electrical control of any door equipped with cylindrical (key-in-knob/lever) type latchsets. Electrical actuation unlocks strike jaw, releasing latchbolt, so door can be opened without operating latch itself. Extremely compact mechanism fits into jamb sections as shallow as 1-21/32". Features Include: • Case: Approx. 1" x 3-3/8" x 1-5/8" deep. Made of Zinc-aluminum alloy. • Strike Lip: Basic 7240 strikes have lip of proper length for 1-3/4" thick door that closes flush with jamb edge. • Strike Opening: 5/8" x 1-7/16" x 9/16" deep. • Faceplate: Measures 1-1/4" x 4-7/8". Faceplate is flat, with square corners. Technical Specifications: UL ® UL Listed for Burglary Resistance UL 10B for up to 3-hour Fire Door Assemblies, VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • Case: Approx. 1" x 3-3/8" x 1-7/8” deep. Made of Zinc-aluminum alloy. • Strike Lip: Basic 7270 strikes have lip of proper length for 1-3/4" thick door that closes flush with jamb edge. • Strike Opening: 3/4" x 1-7/16" x 5/8” deep. • Faceplate: Measures 1-1/4" x 4-7/8". Faceplate is flat, with square corners. Technical Specifications: UL ® UL Listed for Burglary Resistance UL 10B for up to 3-hour Fire Door Assemblies, VOLTAGE Available in 12, 16 or 24 volt AC and DC. DC and AC Continuous units are silent, AC intermittent units "buzz" on operation. CURRENT DRAW/AMPS Volts AC Int. DC or AC Cont. 12 1.42 .33 16 1.03 .22 24 .74 .17 Visit us on the web at www.akronhardware.com ADAMS RITE For Mortise Latches without deadbolt by others. Remote electrical control of any door equipped with a Mortise Type latchset. Electrical actuation unlocks strike jaw, releasing latchbolt so door can be opened without operating latch itself. Extremely compact mechanism fits hollow jamb sections as shallow as 1-7/8". 11 7270 / Fire Rated in Fail-Secure Mode For Hollow Steel Jambs ADAMS RITE 12 How To Order Adams Rite Electric Strikes Specify Model Voltage 3 12 Volt 4 16 Volt 5 24 Volt Current & Duty 1 DC Continuous or Intermittent 2 AC Continuous 4 AC Intermittent 0 5 7 9 Features Std/Fail-Secure Fail-Safe Monitor/Fail-Safe Monitor/Fail-Secure 7100 - 315 - 605 Finish** 628 Clear Anodized 613 Oil Rubbed Bronze Standard Package: Individually boxed with mounting screws, mounting brackets and adhesive shims to accommodate jamb or stile extrusion thickness greater or less than nominal 1/8 inch. Options: 4603 Rectifier Converts AC to DC, installs in low voltage line between transformer and strike. Rated 2 amps. (200 PIV). 4605 Transformer Converts 120VAC to 24VAC. Rated 40Volt-amp output assures plenty of power for strike release. Patented mounting bracket fits in knockout hole of standard junction boxes. 4606 Transformer Plug-in version for standard wall outlet. See separate specification sheet for more information on Strike options. Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 13 How To Order Adams Rite Electric Strikes ADAMS RITE Notes: Visit us on the web at www.akronhardware.com 14 MS1850S Series MS Deadbolt (1" x 6-7/8" Faceplate) ® ADAMS RITE A huge bolt of laminated stainless steel, nearly three inches long, activated by an uncomplicated pivot mechanism, has made this basic MS® Deadbolt the standard of the narrow stile door industry. The length of this bolt provides maximum security for a single leaf door, even a very tall and flexible one or an installation where the gap between door and jamb is greater than it should be. Features Include: • • • • Cylinder Backset: 31/32", 1-1/8" or 1-1/2" only. Case: Steel with corrosion-resistant plating. 1" x 6" x depth. Bolt: 5/8" x 1-3/8" x 2-7/8" with 1-3/8" throw. Operation: 360º turn of key or thumbturn throws or retracts the counterbalanced bolt. Key can be removed only when bolt is in a positively locked or unlocked position. • Cylinder Cam: MS1850S Series locks are operable by any standard 1-5/32" diameter mortise cylinder with special MS® cam. Technical Specifications: STANDARD PACKAGE Individually boxed with machine screws for mounting. Cylinders and/or thumbturn available at extra cost. Shipping weight: 1-1/2 lbs. HOW TO ORDER Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • • • • Cylinder Backset: 1-1/2" only. Case: Steel with corrosion-resistant plating. 1" x 6" x 2-1/4". Bolt: 5/8" x 1-3/8" x 2-7/8" with 1-3/8" throw. Operation: 360º turn of key or thumbturn throws or retracts the counterbalanced bolt. Key can be removed only when bolt is in a positively locked or unlocked position. • Cylinder Cam: MS1850SN Series locks are operable by any standard 1-5/32" diameter mortise cylinder with special MS® cam. Technical Specifications: STANDARD PACKAGE Individually boxed with machine screws for mounting. Cylinders and/or thumbturn available at extra cost. Shipping weight: 1-1/2 lbs. HOW TO ORDER ALSO AVAILABLE - 2331 DEADBOLT CLICK HERE FOR MORE INFORMATION Visit us on the web at www.akronhardware.com ADAMS RITE For hollow metal or wood doors prepared for hardware according to the specifications of the American National Standards Institute, this MS® deadbolt provides maximum security and ease of installation. Its standard 1-1/2" backset dimension provides adequate clearance for the deep stop on the door jamb of hollow metal entrances. 15 MS1850SN Series ANSI Size MS® Deadbolt ADAMS RITE 16 Threshold Bolt 4015 4005 Strike Bolt Guide Adding the 4015 bolt to a pivoted bolt MS® deadbolt allows Maximum Security for pairs of doors by the turn of a single key. Simultaneously dropping a hardened steel hexbolt into the threshold and pivoting the massive MS® bolt into the mating door’s stile, the two-point lock secures the entire double door entrance.The 4015 threshold bolt is harnessed to the rear of the pivoted bolt. It may be added to any basic MS1850S or MS1850SN deadbolt. Features Include: • Threshold Bolt: Hexagonal 3/8" flat to flat. Made of hardened steel and plated for corrosion resistance. Technical Specifications: STANDARD PACKAGE Packed separately with bolt guide, screws and attachment pin. Shipping weight: 1 lb. Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Rod Guide Header Strike Features Include: • Adjustment: Minor adjustment of rod length is accomplished by turning nylon rod end. • Header Bolt: 1/2" x 1-1/2" expanding bolt with 5/8" throw. Housed in 1-1/2" x 2-3/4" x 5/8" case. Technical Specifications: STANDARD PACKAGE Packed separately with rod guide, screws and header strike.Shipping weight:1 lb. Visit us on the web at www.akronhardware.com ADAMS RITE Designed to add a top-of-door third locking point for pairs of doors with an MS® pivoted bolt deadbolt and 4015 Threshold bolt in the active leaf. The 4085 is mounted in the inactive leaf. This additional bolt, triggered by the pivoted MS® bolt, expands in a “scissors” action to center itself in its strike as it rises. This action saves the key holder from the difficulty of lining up the doors with three separate strikes, even if doors are misaligned due to faulty installation or settling. The threepoint features may be added to any basic MS1850S or MS1850SN deadbolt. 17 Header Bolt (Pairs of Doors Only) 4085 18 MS® Deadbolt / Latch MS+1890 Series ADAMS RITE Deadbolt Maximum Security after hours plus traffic control convenience for management during the business day. Typical installation is a bank or store requiring three modes of door control: 1. Both lock and latch bolts retracted for unrestricted entry and exit during business hours, 2. Handle-operated latch for exit-only traffic just after closing, and 3. Maximum Security hookbolt for overnight lockup. NOTE: Handle or paddle operates latchbolt only. 4505 Armored Strike Features Include: • • • • • • Cylinder Backset: Available in 31/32", 1-1/8" or 1-1/2". Case: Steel with corrosion-resistant plating. 1" x 7-3/8" x depth. Latch Bolt: 5/8" x 5/8" with 7/16" throw. Handing easily reversible. Lock Bolt: 5/8" x 1-3/8" with 13/16" throw. Armored Strike: Satin stainless steel trim plate with steel mounting plate and dust box. Operation: 360º turn of key or thumbturn throws or retracts the hookshaped deadbolt. 120º further turn retracts latch bolt as well. • Cylinder Cam: MS+1890 Series locks are operable by any standard 1-5/32" diameter mortise cylinder with special MS® cam. Technical Specifications: HOW TO ORDER Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 19 Wood Decor Deadbolt 5017 4810 Box Strike Features Include: • • • • Backset: 1-3/16“ (1.25 including faceplate). Case: 1/2“ x 4 x 1-19/32” deep. Stainless steel. Bolt is laminated stainless steel. Faceplate: 5/8“ x 4-1/2” with radiused ends. Stainless steel. Operation: 45º rotation of turn or key throws or retracts bolt. Bolt is self-protecting: if door is shut while bolt is extended, it will retract, preventing damage or accidental lockout. Technical Specifications: HOW TO ORDER Visit us on the web at www.akronhardware.com ADAMS RITE For wood framed sliding doors the 5017 Deadbolt provides the same thousand pound strength that the MS1847 Deadbolt provides for metal stiles. A deeper backset clears the recessed jamb used with wood doors. Bolt throw is easily adjusted by means of a screw in the faceplate. Mounting is by through-bolts, which also secure the inside turn and outside cylinder when installed. ADAMS RITE 20 Bottom Rail Deadbolt MS1861 Using the same overcenter/pivot locking mechanism as the basic MS® deadbolt, the MS1861 lies horizontally in the bottom rail of ultra-narrow stile doors, which have insufficient vertical space for a lock and tempered glass doors, which have no stile at all. The hardened steel cylindrical bolts allow simple drilled strike holes of a relatively small size to minimize the nuisance and danger presented by some threshold strikes in collecting debris and catching women’s heels. MS1861-02 locks either single-leaf or paired doors. MS1861-01 MS1861-02 Features Include: • Case: Steel with corrosion-resistant plating. 1" x 6" x 1-13/16". • 4014 Conversion Kit: To convert MS1861-01 to MS1861-02, Kit 4014 provides horizontal bolt assembly with guide and attachment fittings (also sold separately). • Bolts: 3/8" diameter. Stainless steel vertical threshold bolt has 13/16" throw. Hardened steel horizontal bolt has 1-1/8" throw. • Operation: 360 turn of key or thumbturn throws or retracts bolt(s). Key can be removed only when bolts are in a positively locked or unlocked position. Technical Specifications: Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Available Finishes from Stock 603 RC121 Dark Bronze 652 Satin Chrome 639 Zinc on Steel Satin Bronze Features Include: • Security Ring: Made of hardened steel. Free-swiveling when properly installed. • Retainer Ring: Hardened steel, plated for corrosion resistance. Permits security ring to swivel. • Trim Finish: Zinc plated (603). Contact factory for other available finishes. Exit Indicator 4089 Provides unmistakable notification of an exit door’s “locked” or “open” condition. Under many local building safety codes, this allows the use, in certain occupancies, of a security deadlock instead of less secure panic devices. Features Include: • Message Panel: “OPEN” appears in black letters on white background when lock is retracted and “LOCKED” in red letters when actuated. • Material/Finish: Indicator escutcheon is available as zinc alloy with 130 (Satin Aluminum) or RC121 (Dark Bronze). • Compatible Locks: MS1850S; MS1850SN; MS+1890 Visit us on the web at www.akronhardware.com ADAMS RITE The MS4043 cylinder guard offers a three-way defense: First, the outer shield ring is fully beveled to offer poor purchase for either prying or twisting. Second, this ring is hardened steel so that the combination of shape and hardness make it virtually impossible to grip, even with sharpened tools. Third, in the event that a prying tool, such as a cold chisel, can be driven into the stile behind the shield ring, the would be burglar is obliged to pull a heavy steel plate through a round hole in the 1/8" metal door stile. 21 Cylinder Guard MS4043 22 ADAMS RITE Electrified Deadlatch 4200 Series The 4200 eLatch combines mechanical locking hardware with electrified access control while working within standard aluminum entrance door preparations. Always operable from the inside via handle or paddle device. Entry via keyed mortise cylinder or access control element. Fail-secure lock with form “C” latch status monitor standard. Rated for continuous operation in either 12 VDC or 24 VDC versions. 1-3/4” minimum door thickness required. Both Flat and Radius Faceplates are supplied. THIS SIDE UP MODEL B C STA 12 VD 0.4A 24 VD 0.2A 4204 Strike Shown ADAM S RIT E B C STA D ACTURE MANUF Features Include: • • • • • Cylinder Backset: 31/32" and 1-1/8” Case: Steel with corrosion-resistant plating. 15/16" x 5-13/16" x depth. (Depth varies) Latch Bolt: 5/8" x 1" x 5/8" throw. Auxiliary Bolt: All metal. Deadlocks latch bolt to prevent “loiding” or case-knife entry. Strikes: 4203 no-cut surface mounted strike for easy installation. Specify 4204 mortised strike for flush mounted installations or when replacing existing 4501/4502/4901/4902 strikes • Operation: Turn key, apply voltage, or operate handle or paddle to release the springloaded latch bolt. Electrically rated for continuous duty for timed applications. Technical Specifications: Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 23 Deadlatch (For Metal Stile Glass Doors) 4510 Series ADAMS RITE Flexibility of traffic control during and after business hours is offered by 4510 Series Deadlatches. A reverse turn of the key while bolt is held retracted retains the bolt, to allow two-way traffic for hospitals, banks, stores and other buildings which require free entrance at certain times and exit-only at other times. Interchangeable, without stile modification, with any MS1850A or MS1850S deadbolt of same backset and faceplate shape. Features Include: • • • • • Cylinder Backset: 7/8", 31/32",( 1-1/8" or 1-1/2" special order only). Case: Steel with corrosion-resistant plating. 1" x 5-13/16" x depth. Latch Bolt: 1/2" x 1" x 1/2" throw. Auxiliary Bolt: All metal. Deadlocks latch bolt to prevent “loiding” or case-knife entry. Strikes: Standard strike furnished is 4502-01 for flat jamb where door closes flush or nearly flush. • Operation: Turn key or operate handle to retract spring-loaded latch bolt. To hold bolt retracted, push it in and secure by reverse turn of key. • Cylinder Cam: 4710 Series Deadlatches are operable by any standard 1-5/32" diameter mortise cylinder with special MS® cam. Technical Specifications: HOW TO ORDER "A" 1.00 25.4 .88 22.3 BACKSET MEASURED AT CENTERLINE OF STILE NOSE .22 5.6 .50 12.7 6.81 173.0 .53 12.7 1.437 36.5 5. 80 147.3 FLAT 4910 RADIUS 4911 6.38 6.88 162.0 174.7 .50 13.5 RADIUS w/WEATHERSTRIP 4911W LH BEVEL MAX. 2.475 62.86 4912(LH) .25 6.3 SHOWN RIGHT HAND. REVERSIBLE BY REMOVING BOLT AND REINSTALLING FOR OPPOSITE HAND. Visit us on the web at www.akronhardware.com RH BEVEL 4912(RH) ADAMS RITE 24 Replacement Deadlatch 4530 Series 4530 Series Deadlatches are designed to fit, without alteration, the stile cutout for MS1850* Series Deadbolts of same backset. (They do not, however, provide the maximum security level of the MS Deadbolt and should not be considered an equivalent replacement.) Also replaces, without alteration, older 4250 Series Deadlatches. Features Include: • • • • Cylinder Backset: 7/8", 31/32" or 1-1/8" only. Case: Steel with corrosion-resistant plating. 1" x 5-13/16" x depth. Strikes: Standard strike furnished is 4501-01 for flat jamb. Latch Bolt: 1/2" x 1" x 1/2" throw. All metal with hardened steel internal pins. Handing is easily reversible without special tools. • Auxiliary Bolt: All metal. Deadlocks latch bolt to prevent “loiding” or caseknife entry. • Operation: Turn key or operate handle to retract spring-loaded latch bolt. To hold bolt retracted, push it in and secure by reverse turn of key. Technical Specifications: STANDARD PACKAGE Individually boxed with strike and machine screws for mounting. Cylinders, paddle or handle available at extra cost. Shipping weight: 1-1/4 lbs. HOW TO ORDER Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 NOTE: Not compatible with 7/8" backset locks. Features Include: • • • • Housing: Aluminum casting is 1-3/8" wide x 7-1/2" long x 1" deep. Stop Clearance: Lever housing projects 11/16" forward of cylinder backset centerline. Lever: 3" long aluminum with end-return design offers comfortable grip to lock or unlock. Indicator: Words “LOCKED” in red letters or “OPEN” in black letters appear on white background when lock is thrown or retracted. • Compatible Deadbolts: MS1850S • Operation: Turn lever downward 90º to unlock. When released, lever returns to horizontal. Turn lever upward 90º to relock. Key operation from outside is not affected. Clutching action prevents damage to internal components. • Cylinder Cam: MS+1890 Series locks are operable by any standard 1-5/32" diameter mortise cylinder with special MS® cam. Technical Specifications: Available Finishes from Stock 628 Clear Anodized 130 121 313 Dark Bronze Anodized 119 315 Black Anodized Visit us on the web at www.akronhardware.com ADAMS RITE Easy unlocking of any MS® deadbolt by approximately 3 lbs. downward force on a 3" lever. Lever is spring loaded to horizontal, relocks with upward motion. Indicator signals lock status. Can be installed in place of existing key cylinder or cylinder type thumbturn on inside of door. 25 MS® Deadbolt Lever 4550 26 4900 Series Deadlatch ADAMS RITE Flexibility of traffic control and installation is offered by the 4900 Series Deadlatches. A reverse turn of the key while bolt is held retracted retains the bolt, to allow two way traffic for applications which require free entrance at certain times and exit-only at other times. Interchangeable, without stile modification, with any MS1850A or MS1850S deadbolt of same backset and faceplate shape. Also retrofits to existing 4500/4700 Deadlatch preparations. Features Include: • • • • • • Cylinder Backset: 1-1/8” or 1-1/2” only. Case: Steel with corrosion-resistant plating. 7/8” x 5-13/16" x depth. Latch Bolt: 5/8" x 1" x 5/8" throw. Auxiliary Bolt: Stainless Steel. Strikes: Standard 4902 for flat jamb. 4901 for Retrofit installations. Operation: Turn key or operate handle or paddle to retract spring-loaded latch bolt. To hold bolt retracted, push it in and secure by reverse turn of key. • Cylinder Cam: 4900 Series Deadlatches are operable by any standard 1-5/32" diameter mortise cylinder with special MS® cam. Technical Specifications: HOW TO ORDER 16.00 22.86 25.10 BACKSET MEASURED AT CENTERLINE OF STILE NOSE 6.30 12.55 174.75 36.50 147.32 162.05 172.72 15.24 FLAT FACEPLATE CAN BE ADJUSTED FOR RIGHT OR LEFT BEVELED EDGE DOORS 9.39 62.86 SHOWN RH / LHR. BOLT IS REVERSIBLE FOR OPPOSITE HAND. Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 27 4920AN Series ANSI Size Deadlatch Features Include: • • • • • • Cylinder Backset: 1-1/2" or 2-3/4” only. Case: Steel with corrosion-resistant plating. 1" x 5-13/16" x depth. Latch Bolt: 5/8" x 1" x 5/8" throw. Auxiliary Bolt: All metal with hardened steel pin. Strikes: Stainless steel, US32D Satin finish (630). Operation: Turn key or operate handle to retract spring-loaded latch bolt. To hold bolt retracted, push it in and secure by reverse turn of key. • Cylinder Cam: 4720AN Series Deadlatches are operable by any standard 1-5/32" diameter mortise cylinder with special MS® cam. Technical Specifications: HOW TO ORDER HOW BACKSET IS MEASURED: 16.0 CYLINDER 22.8 31.7 CL FLAT BACKSET MEASURED AT CENTERLINE OF DOOR EDGE CL 8.6 BEVEL 26.7 36.5 147.3 203.2 201.7 184.2 15.2 9.4 FACEPLATE CAN BE ADJUSTED FOR RIGHT OR LEFT BEVELED EDGE DOORS 6.3 SHOWN RH / LHR. BOLT IS REVERSIBLE FOR OPPOSITE HAND. Visit us on the web at www.akronhardware.com ADAMS RITE For hollow metal or wood doors prepared for hardware according to the specifications of the American National Standards Institute. Interchangeable, without stile or jamb modification, with any MS1850SN Deadbolt of same faceplate shape. Replaces 4520ANSI and 4720ANSI Deadlatches. ADAMS RITE 28 Deadlatch Paddle 4590 An alternative to knob or lever handles. Makes opening a latched door as natural as opening an unlatched one – just push or pull in the direction the door swings. Available for any Adams Rite Series 4500 or 4900 deadlatch (except 4950) or MS+1890 lock/latch. 4580 Cam Plug Features Include: • Paddle: Extruded aluminum, 628 Clear Anodized finish (US28). 313 Dark Bronze Anodized also available. • Cam Plug: Furnished for use with Series 4500 or 4700 latches. • Escutcheon: Zinc alloy with Black Ritecoat finish. • Operation: Available in four modes: Push to left, Push to right, Pull to left and Pull to right (field reversible). Technical Specifications: STANDARD PACKAGE Individually boxed with mounting hardware. Units for 4000 Series latches include cam plug. Shipping weight: 1- 1/2 lb. HOW TO ORDER Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Hex Key for Dogging 4580 Cam Plug Features Include: • Paddle: Extruded aluminum, 628 Clear Anodized finish (US28). 313 Dark Bronze Anodized also available. • Paddle Dogging (”Push” versions only): Turning hex key in escutcheon holds the paddle down, leaving door free-swinging. Dogging key provided. • Cam Plug: Furnished for use with Series 4500 or 4700 latches. (Not used with MS+1890 lock/latch.) • Escutcheon: Zinc alloy with Black Ritecoat finish. • Operation: Available in four modes: Push to left, Push to right, Pull to left and Pull to right. Can be reconfigured to any mode in the field. Dogging not to be installed in pull configuration. Technical Specifications: HOW TO ORDER Visit us on the web at www.akronhardware.com ADAMS RITE An alternative to knob or lever handles. Makes opening a latched door as natural as opening an unlatched one – just push or pull in the direction the door swings. Available for any Adams Rite Series 4500 or 4900 deadlatch (except 4950) or MS+1890 lock/latch. 29 Deadlatch Paddle 4591 ADAMS RITE 30 Deadlatch Handles 4560 / 4561 / 4565 4560 Designed to operate 4500 or 4900 Series latches (except 4950) by a natural downward hand movement, these handles incorporate an activator cam disc that mounts on the handle escutcheon and fits solidly into the cylinder hole of the latch. Not intended for use as a door pull. 4565 Features Include: • 4560 Handle: Lever of satin chrome plated zinc alloy is shaped to fit the hand, with a concave thumb-rest portion that tends to keep knuckles and thumb safely away from the jamb, even on a short backset narrow stile. Finish: 682 (US26D). • 4565 Handle: Thumbturn of minimum practical length is designed to offer a firm grip to the fingertips. Ideal for doors where latch is operated infrequently or in emergencies only. Finish: 682 (US26D). Technical Specifications: Available Finishes from Stock RC130 Satin Aluminum RC121 Dark Bronze For Adams Rite Parts, Available For Immediate Shipment, See Our Manufacturers Parts Section. Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • Pull Handle: Cast zinc alloy, finished to match housing. • Measures approx. 10" x 3" x 2-1/4" deep. • Operation: Pull handle 27º to unlock/unlatch. Available in two modes: lock after each activation or latch only. Key operation from outside unlocks the handle to activate the deadlatch. • 4593E: Mounted solenoid allows latch pull to be wired for integration with card readers, access pads or other access control devices. After a single use, the latch will revert to locked mode. Specify 24VDC (.3 amps) or 12VDC (.6 amps). Technical Specifications: Available Finishes from Stock 130 628 Clear Anodized 121 313 Dark Bronze Anodized Visit us on the web at www.akronhardware.com ADAMS RITE The Latch Pull offers ease of use and greater flexibility for narrow, medium and wide stile aluminum doors with Adams Rite 4500/4900 Deadlatches and 8400 Exit Device latches. 31 Latch Pull 4593 / 4593E ADAMS RITE 32 Eurostyle Deadlatch Handles 4568 / 4569 Designed to operate 4500 or 4900 Series latches (except 4950) by a natural downward hand movement. These handles incorporate an activator cam disc that mounts on the handle escutcheon and fits solidly into the cylinder hole of the latch. Not intended for use as a door pull. 4568 4569 Features Include: • 1-3/8" x 4", designed to match the narrow stile door’s clean lines. • Cam Plugs: Secured in latch body by cylinder setscrew, plug is also rigidly tied to handle escutcheon by hardened steel pins. Handing can be reversed by removing a spring clip, “flopping” the cam and replacing the clip. • Levers: Lever of cast aluminum. Technical Specifications: Available Finishes from Stock 130 Satin Aluminum 121 Dark Bronze 119 Satin Black STANDARD PACKAGE Packed individually with cam plug handed LH or RH as specified. Two 10-32 mounting screws furnished. Shipping weight: 1/2 lb. Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 33 Deadlatch Strikes 4901 / 4902 ADAMS RITE 4901-01 Standard FLAT strike includes molded black plastic dust boxand closure of the unused lower strike opening with steel mounting plate. Long face is designed to fill strike area of MS® deadbolts with which the deadlatch is interchangeable. 4901-02 Same as 4901-01, except with RADIUSED strike plate, for nose of opposite door when latching pairs. Features Include: • 4902-01: Standard FLAT strike furnished with the 4500 and 4900 Series deadlatches. Includes molded black plastic dust box and steel mounting plate. Short face design. • 4902-02: Same as 4902-01, except with RADIUSED strike plate, for nose of opposite door when latching pairs. Technical Specifications: DEADLATCH IN DOOR 10-32 TAP CL MOUNTING PLATE C’SK FOR #10 FLAT HEAD STRIKE PLATE 2.8 CL 9.6 1.5 9.6 14.2 6.3 DUST BOX 19 CYLINDER 4500 OR 4700 LATCH 9.4 31.7 117.6 155.7 28.7 with Dust Box & Mounting Plate 98.5 17 3.8 28.7 136.5 62.7 29.9 19 14.2 DRILL AND C’SK FOR # 10 FLAT HEAD SCREWS 136.52 with Dust Box & Mounting Plate FURNISHED WITH FOUR # 10-32 x 1/2 FLAT HEAD MACHINE SCREWS 14.4 3.17 28.7 10-32 TAP C’SK FOR #10 FLA T HEAD DEADLATCH IN DOOR MOUNTING PLATE CL 2.8 9.6 CL STRIKE PLATE 9.6 14.2 6.3 DUST BOX 19 R 117.72 + 0.38 -0.0 R CYLINDER 4500, 4700 OR 4900 LATCH 1.5 31.7 104.9 66.8 with Dust Box & Mounting Plate 28.7 47.7 9.4 85.7 3.8 R 17 62.7 R 29.9 28.7 66.92 + 0.38 -0.0 14.2 3.17 4501/4502 Deadlatch Strikes discontinued. Limited quantities available. with Dust Box & Mounting Plate DRILL AND C’SK FOR # 10 FLAT HEAD SCREWS 85.72 14.4 Visit us on the web at www.akronhardware.com FURNISHED WITH FOUR # 10-32 x 1/2 FLAT HEAD MACHINE SCREWS 34 Surface Vertical Rod Exit Device 3100 Series Fire-Rated / 8100 Series Life-Safety ADAMS RITE • For Wood & Hollow Steel Doors • Patented top latching mechanism interlocks door to frame • Adjustable steel rods protected in contoured covers • Pushbar clad or anodized, not plated, in a variety of finishes • Easy to install • Clean, unobtrusive design • Strong, durable construction for a high level of security Features Include: • • • • • • • • • • Handing: Device is non-handed. Lever Entry Trim is field reversible. Pushbar Length: Standard Sizes: Dimensioned for 36" openings. Bar Height: Standard model adjusts from 30" to 44". Door Height: Standard model fits up to 8ft. door, with bar height at 40" - 44". Door Thickness: Suits 1-3/4" standard. Materials: Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. Stile Width: 3100 – Minimum 3-3/4"*; 8100 – Minimum 3-3/4". Dogging: Standard dogging with hex key. Strike: Made of hardened steel. Supplied with device. Warranty: Two year limited. Technical Specifications: Available Finishes from Stock 313 Dark Bronze Anodized (Available in 8100 only.) 628 Clear Anodized US32D Satin Stainless Pushbar Dimensions Bolts and Strikes The patented top latching mechanism utilizes a rotating Top Bolt which deadlatches around the Header Strike, interlocking the door to the frame. Standard and Fire-rated Header Strikes are available. For wood frames, an additional plate is supplied for securing the Header Strike. The hexagonal, hardened steel Bottom Bolt is shielded in a cast housing for strength and stability. Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • • • • • • • • Handing: Device is non-handed. Lever Entry Trim is field reversible. Pushbar Length: Standard Sizes: Dimensioned for 36" openings. Bar Height: Standard model adjusts from 30" to 44". Door Height: Standard model fits up to 8ft. door, with bar height at 40" - 44". Door Thickness: Suits 1-3/4" standard. Stile Width: Minimum 2" Stile. Fits Narrow, Medium and Wide Stile aluminum doors. Dogging: Standard dogging with hex key. Materials: Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. • Strike: Made of hardened steel. Supplied with exit device. • Warranty: Two year limited. Technical Specifications: Available Finishes from Stock 313 Dark Bronze Anodized 628 Clear Anodized Pushbar Dimensions Bolts and Strikes The patented top latching mechanism utilizes a rotating Top Bolt which deadlatches around the Header Strike, interlocking the door to the frame. Standard Header Strikes are supplied with exit device. The hexagonal, hardened steel Bottom Bolt is shielded in a cast housing for strength and stability. Visit us on the web at www.akronhardware.com ADAMS RITE • Patented top latching mechanism interlocks door to frame • Adjustable steel rods protected in contoured covers • Pushbar clad or anodized, not plated, in a variety of finishes • Easy to install • Clean, unobtrusive design • Strong, durable construction for a high level of security 35 Narrow Stile Surface Vertical Rod Exit Device 8200 Series for Aluminum Doors 36 Mortise Exit Device 3300 Series Fire-Rated / 8300 Series Life-Safety ADAMS RITE • For Wood & Hollow Steel Doors • Heavy duty deadlatching mechanism • Pushbar clad or anodized, not plated, in a variety of finishes • Easy to install • Clean, unobtrusive design • Strong, durable construction for a high level of security Features Include: • • • • • • • • Handing: Specify handing and bevel if applicable. Lever Entry Trim is field reversible. Pushbar Length: Standard Sizes: Dimensioned for 36" openings. Door Thickness: Suits 1-3/4" standard. Stile Width: 3300 – Minimum 5"*; 8300 – Minimum 3-3/4". Materials: Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. Dogging: Standard dogging with hex key for 8300 Series only. Strikes: Made of stainless steel. Supplied with exit device. See strike options below. Warranty: Two year limited. Technical Specifications: Available Finishes from Stock 313 Dark Bronze Anodized (Available in 8300 only.) 628 Clear Anodized US32D Satin Stainless (Available in 3300 only.) Pushbar Dimensions Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • • • • • • Handing: Specify handing and bevel if applicable. Lever Entry Trim is field reversible. Pushbar Length: Standard Sizes: Dimensioned for 36" & 42" openings. Door Thickness: Suits 1-3/4" standard. Can be modified for thicker doors. Stile Width: Minimum 2" Stile. Fits Narrow, Medium and Wide Stile aluminum doors. Materials: Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. Dogging: Standard dogging with hex key or cylinder dogging option. Electric dogging also available. 36" width x 1-1/8" backset only. • Strikes: Made of stainless steel. Supplied with exit device. See Strike options below. • Warranty: Two year limited. Technical Specifications: Available Finishes from Stock 313 Dark Bronze Anodized 628 Clear Anodized Pushbar Dimensions Strikes A variety of strikes are available for different applications and conditions. Visit us on the web at www.akronhardware.com ADAMS RITE • Heavy duty deadlatching mechanism • Pushbar clad or anodized, not plated, in a variety of finishes • Easy to install • Clean, unobtrusive design • Strong, durable construction for a high level of security 37 Narrow Stile Mortise Exit Device 8400 Series for Aluminum Doors 38 Narrow Stile Concealed Vertical Rod Exit Device 8600 Series Life-Safety ADAMS RITE • For Aluminum Doors • Patented top latching mechanism interlocks door to frame • Top and bottom adjustable steel rods • Pushbar anodized or clad, not plated, in a variety of finishes • Easy to install • Clean, unobtrusive design • Strong, durable construction for a high level of security Features Include: • • • • • • • • • Handing: Device is non-handed. Lever Entry Trim is field reversible. Pushbar Length: Standard Sizes: Dimensioned for 36" & 42" openings. Door Thickness: Suits 1-3/4" standard. Stile Wall: Doors with stile walls other than 1/8" require modification. Stile Width: Minimum 2" Stile. Fits Narrow, Medium and Wide Stile aluminum doors. Bar Height: Adjustable from 30" to 44". Door Height: Standard unit adjustable for doors up to 66" above the selected bar height. Materials: Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. Dogging: Standard dogging with hex key or optional cylinder dogging. Electric dogging available. • Strike: Made of hardened steel. Supplied. • Warranty: Two year limited. Technical Specifications: Available Finishes from Stock Dark Bronze Anodized 313 628 Clear Anodized US3 Bright Brass (36" only.) Pushbar Dimensions Bolts and Strikes The patented top latching mechanism utilizes a rotating Top Bolt which deadlatches around the Header Strike, interlocking the door to the frame. Supplied with Standard or Firerated Header Strikes. The hexagonal, hardened steel Bottom Bolt works in harmony with the Top Bolt. Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • • • • • • • Handing: Device is non-handed. Lever Entry Trim is field reversible. Pushbar Length: Standard Sizes: Dimensioned for 36" openings. Door Thickness: Suits 1-3/4" standard. Stile Width: 3600 - Minimum 3-1/2". Materials: Pushbar made of extruded aluminum. Strike: Made of hardened steel. Supplied with exit device. Warranty: Two year limited. Technical Specifications: Available Finishes from Stock Clear Anodized 628 Pushbar Dimensions Bolts and Strikes The patented top latching mechanism utilizes a rotating Top Bolt which deadlatches around the Header Strike, interlocking the door to the frame. Supplied with Standard or Firerated Header Strikes. The hexagonal, hardened steel Bottom Bolt works in harmony with the Top Bolt. Visit us on the web at www.akronhardware.com ADAMS RITE • Patented top latching mechanism interlocks door to frame • Top and bottom adjustable steel rods • Pushbar clad or anodized, not plated, in a variety of finishes • Easy to install • Clean, unobtrusive design • Strong, durable construction for a high level of security 39 Metal Door Concealed Vertical Rod Exit Device 3600 Series Fire-Rated 40 Rim Exit Device 3700 Series Fire-Rated / 8700 Series Life-Safety ADAMS RITE • For Wood & Hollow Steel Doors • Patented "Starwheel" Bolt interlocks door to frame • Pushbar is anodized or clad, not plated, in a variety of finishes • Unobtrusive design for clean sight lines • Easy to install • Strong, durable construction for a high level of security Features Include: • • • • • • Handing: Device is non-handed. Lever Entry Trim is field reversible. Pushbar Length: Standard Sizes: Dimensioned for 36" openings. Door Thickness: Suits 1-3/4" standard, up to 2-1/4". Stile Width: 3700 - Minimum 3-3/4"*; 8700 - Minimum 3-3/4". Materials: Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. Dogging: Standard dogging with hex key for 8700 Series only. Electric dogging also available for 3700 and 8700 Series. • Strike: Made of hardened steel. Supplied with exit device. • Warranty: Two year limited. Technical Specifications: Available Finishes from Stock 8700 Series Dark Bronze Anodized 313 628 Clear Anodized 3700 Series Clear Anodized 628 Pushbar Dimensions Starwheel Bolt [1] When door closes, the interlocking noseguard and Starwheel bolt close around the strike. The deadlocking slide springs over, locking the Starwheel bolt to the strike. [2] When pushbar is depressed, the deadlocking slide moves back, allowing the door to unlock from the strike. This unique interlock provides solid security and prevents jamb spreading. Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 Features Include: • Handing: Device is non-handed. Lever Entry Trim is field reversible. • Pushbar Length: Standard Sizes: Dimensioned for 30", 36", 42" & 48" openings. Standard width bars can be field cut to the next smallest opening width. • Door Thickness: Suits 1-3/4" standard, up to 2-1/4". • Stile Width: Minimum 2" Stile. Fits Narrow, Medium and Wide Stile aluminum doors. • Materials: Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. • Dogging: Standard dogging with hex key or optional cylinder dogging. Electric dogging also available. • Strike: Made of hardened steel. Standard and narrow version supplied with exit device. • Warranty: Two year limited. Technical Specifications: Available Finishes from Stock 313 Dark Bronze Anodized 628 Clear Anodized Pushbar Dimensions Starwheel Bolt [1] When door closes, the interlocking noseguard and Starwheel bolt close around the strike. The deadlocking slide springs over, locking the Starwheel bolt to the strike. [2] When pushbar is depressed, the deadlocking slide moves back, allowing the door to unlock from the strike. This unique interlock provides solid security and prevents jamb spreading. Visit us on the web at www.akronhardware.com ADAMS RITE • Patented "Starwheel" Bolt interlocks door to frame • Pushbar is anodized or clad, not plated, in a variety of finishes • Unobtrusive design for clean sight lines • Easy to install • Strong, durable construction for a high level of security 41 Narrow Stile Rim Exit Device 8800 Series Life-Safety Clutch Lever Entry Trim Fixed Pulls ADAMS RITE 42 Exit Device Trims & Functions 1.9 48.26 1.42 36.06 .56 14.22 2.91 73.91 4.35 110.49 8.10 205.74 3083E Square Handle Contact us Toll Free at 1-800-321-9602 Fax 1-800-328-6070 HOW TO ORDER Call our Sales department - toll free - for current pricing on all Adams Rite products Visit us on the web at www.akronhardware.com ADAMS RITE A switch in the exit device pushbar mounted on the hinge end. Switch can be used to activate signal light, horn, monitor or other devices. Most common application is to release maglock when pushbar is depressed. Switch can be wired for normally open or normally closed depending upon application. Can be retrofit in field to existing exit device. Dual switch version offers redundancy as required by some building codes or the option of operating a second signaling device. 43 Monitor / Signal Switch