CITROËN Alert Zones - Notice eMyWay - UK

CITROËN ALERT ZONES
I N S T A L L A T I O N H A N D B O O K e M y W ay
CITROËN ALERT ZONES
INSTALLATION HANDBOOK eMyWay
1. INSTALLING
INSTALLING THE FILE ON THE NAVIGATION SYSTEM
Once you have downloaded the Alert Zones file from
the CITROËN website you must install it on your
eMyWay navigation system (which contains the Europe
digital mapping system required to guide you).
To install your Alert Zones file on your eMyWay use a
blank USB stick (to avoid any potential recognition
issues with the medium).
After inserting the blank USB stick into the computer,
select file (.exe):
1. Click on “Exécuter” (Run) or “Ouvrir” (Open), and
this will call up a “Self-extracting Archive” window on
your computer’s screen (see example on RH side).
2. Click on the button
right of “Extract to” in order
to select the USB stick or folder you wish the data to be
copied onto.
3. Click on “Start”.
To check that the copy has been successful, you may
check the USB stick for the presence of the:
- MAPPE folder (and subfolders)
- UPG folder
- POI_VER.POI file
Once the data has been successfully copied you may
remove the data medium from your computer and
return to your vehicle to install the Alert Zones file on
your eMyWay navigation system.
August 2012 - 2
CITROËN ALERT ZONES
INSTALLATION HANDBOOK eMyWay
To install the Alert Zones file in your navigation
system, you should connect the USB stick to the
corresponding port which is located:
- Manual gearbox:
gearbox in front of the gearshift
lever,
- Robotised gearbox:
in the stowage
gearbox
compartment closed by a sliding panel.
Your eMyWay will automatically detect the USB
stick inserted and display the message opposite.
Confirm start-up of the updating process by
clicking “ OUI ”(Yes).
When the update is complete, a message tells you
that the Alert Zones file has been successfully
installed on your eMyWay.
You may then eject the USB stick used for
updating.
August 2012 - 3
CITROËN ALERT ZONES
INSTALLATION HANDBOOK eMyWay
2. CONFIGURING RADAR WARNINGS ON THE NAVIGATION SYSTEM
To configure warnings on your eMyWay, press the
“NAV” key:
- Then “Map management”
- Then “Map details”
- And “Transports et automobile”
Tick the “Risk areas” checkbox, and confirm with “OK”.
August 2012 - 4
CITROËN ALERT ZONES
INSTALLATION HANDBOOK eMyWay
You should then configure the audio and visual
warnings when approaching radars. To do this,
press the “NAV” key:
- Select “Options”
- And then “Set parameters for risk areas”
Upon approaching a high-risk area, you may
choose the type of warning:
- Visual warning
- Audio warning with a 15 to 45 seconds notice
for the announcement
- Warning in guidance mode which tells you the
authorised speed limit and gives you a visual
warning should you run in excess (in countries
where this is permitted).
Alert with guidance
In countries where radar information is permitted,
permitted,
when guiding you, the system is able to select
only those fixed speed cameras that are on your
route
---> You are notified of the permitted speed limit
Should you exceed the allowed speed limit, the
circle around the speed limit sign flashes red.
For other types of highhigh-risk area, display is the
same in guided and non guided mode.
August 2012 - 5
CITROËN ALERT ZONES
INSTALLATION HANDBOOK eMyWay
These are the Citroën Alert Zone pictograms :
Fixed speed camera*:
Alert without guidance
Without guidance (no destination), the navigation
system warns you of the presence of Citroën Alert
Zones* in the area near the vehicle
*Depending on the country’s legislation,
information about fixed speed cameras and traffic
light cameras may be prohibited; if this is the case,
then only information about high-risk areas will be
displayed.
Traffic light camera*:
Entering a high-risk area*:
Example of a radar warning in non-guidance
mode: your eMyWay warns that you are
approaching a fixed radar by displaying the icon
opposite in map mode, in addition to the audio
warning (if you have selected the latter).
August 2012 - 6