OILTAP® M Technical Data (TD 050/03)

Transcription

www.reinhausen.com
On-load tap-changer OILTAP® M
Technical Data TD 050/03
NOTE!
The product may have been modified after this document went to press.
We expressly reserve the right to make changes to the technical data, the design or the scope of
delivery.
In general, the information provided and the arrangements agreed during processing of the relevant offers and orders are binding.
Table of Contents
Table of Contents
1
General .........................................................................................................................................................
1.1
1.2
1.3
1.4
1.5
2
3
4
1
Description of type designation ................................................................................................................
Summary of technical data ........................................................................................................................
Overview of on-load tap-changer models ...............................................................................................
Examples of wiring diagrams used in practice (contact designation according to MR standard) ..
Example wiring diagram for OILTAP®M, multiple coarse tap selector design ...................................
1
2
4
8
12
Technical data .............................................................................................................................................
13
2.1
2.2
2.3
2.4
Rated through-current (Iu), rated step voltage (Ui), and step capacity (PStN) ..................................
Contact life ..................................................................................................................................................
Rated withstand voltages of the internal insulation .............................................................................
On-load tap-changer OILTAP®M III 600 Y ... M I 1503 with coarse tap selector
(up to 5 coarse taps) ..................................................................................................................................
13
14
15
Special types ................................................................................................................................................
18
3.1
3.2
3.3
3.4
3.5
Parallel bridges for parallel connection of tap selector planes ............................................................
On-load tap-changer OILTAP®M I 603 and M I 803 with 3-sector diverter switch ........................
On-load tap-changer OILTAP®M I 502 and M II 502 for 16 2/3 Hz ..................................................
Two-pole on-load tap-changer OILTAP®M II 352/502/602 .................................................................
On-load tap-changer OILTAP®M III 350 Y...M I 1503 for linear voltage regulation,
up to 34 operating positions .....................................................................................................................
18
18
19
19
Annex ...........................................................................................................................................................
20
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
17
19
OILTAP®M III 350/500/600 Y-0/W/G (8997102E) .................................................................................
20
OILTAP®M II 352/502/602-0/W/G (8997112E) .....................................................................................
21
OILTAP®M I 351/501/601-0/W/G (8980025E) ......................................................................................
22
OILTAP®M I 802-0/W/G (8997122E) .......................................................................................................
23
OILTAP®M I 1203/1503-0/W/G (8997132E) ..........................................................................................
24
OILTAP®M III K - 0/W/G (7275470E) ......................................................................................................
25
OILTAP®M III 600 Y with multiple coarse tap selector (8995943E) ...................................................
26
OILTAP®M I 601 with multiple coarse tap selector (8995913E) .........................................................
27
OILTAP®M I 802 with multiple coarse tap selector (8995923E) .........................................................
28
OILTAP®M I 1203/1503 with multiple coarse tap selector (8995933E) ............................................
29
OILTAP®M I 351...1503, RM I 601...1502 - tie-in resistors with/without potential switch
(8986902E) ..................................................................................................................................................
30
OILTAP®M II - tie-in resistors with/without potential switch (8986912E) ........................................
31
OILTAP®M III Y, RM III Y - tie-in resistors with/without potential switch (8986922E) ...................
32
OILTAP®M I 351...1503, RM I 601...1502 - ins. cylinder with potential switch without tie-in resistor
(8988043E) ..................................................................................................................................................
33
Supplementary drawings for on-load tap-changers (8980125E) ........................................................
34
OILTAP®M - installation drawing for centric drive unit (893978BE, sheet 1) ..................................
35
OILTAP®M - installation drawing for centric drive unit (893978BE, sheet 2) ..................................
36
On-load tap-changer head, centric drive unit (893899CE) .................................................................
37
OILTAP®M, MS, R, RM - on-load tap-changer head versions (7200261E) ........................................
38
OILTAP®M, MS, R, RM - swivelling range of the gear unit (7200272E) ............................................
39
OILTAP®M - oil compartment contact screening (7303360E) .............................................................
40
Tap selector contact arrangement - no. of contacts per plane 10...22 (8980133E) .......................
41
Mounting position of the tap selector terminals (8904778E) .............................................................
42
Technical Data 050/03 OILTAP® M
The copying, distribution and utilization of this document as well as the communication of its contents to others without expressed authorization is prohibited.
Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or ornamental design registration.
©Maschinenfabrik Reinhausen GmbH 2007
050/03/01/0
Table of Contents
4.24
4.25
4.26
4.27
4.28
4.29
4.30
4.31
4.32
4.33
4.34
4.35
4.36
OILTAP®M, RM, VACUTAP®VRC/VRE - connection cables 3W, 1G, 3G (7235901E) .........................
OILTAP®M and VACUTAP®VRC/VRE - fine tap selector and change-over selector screening
(7303350E) ..................................................................................................................................................
OILTAP®M I 802/8031203/1503 - bridges for parallel connection of tap selector terminals
(8995981E) ..................................................................................................................................................
OILTAP®M, MS, RM - horizontal drive shaft, centric drive unit (8938968E) ....................................
OILTAP®M III 350/500/600 Y - tap selector winding (8911073E) ......................................................
OILTAP®M I 351/501/601 - tap selector winding (8911086E) ...........................................................
OILTAP®M I 1203/1503 - tap selector winding (8911094E) ...............................................................
OILTAP®M I 802 (8911103E) - tap selector winding ............................................................................
Special version for bell-type tank installation (8967629E) .................................................................
OILTAP®M, MS, R, RM with flange for pressure relief valve (8951686E) ..........................................
Tap selector bottom with additional screening - reversing change-over selector version
(8939341E) ..................................................................................................................................................
Tap selector bottom with additional screening - coarse change-over selector version
(8939351E) ..................................................................................................................................................
Tap selector bottom with hole D20 and D13 (7256491E) ....................................................................
43
44
45
46
47
48
49
50
51
52
53
54
55
Technical Data TD 050/03 OILTAP® M
050/03/01/0
1
General
1
General
1.1
Description of type designation
Example
M
III
600
Y - 72,5 / C - 10
-
/
19
1W
R
basic wiring diagram
Type
Number of phases
IUm [A]
Number of
phases used
Applications
Um [kV]
OILTAP® M
1 phase
2 phases
3 phases
MI, MII, MIIIY
MI, MII, MIIIY
MI, MII, MIIIY
MI
MI
MI
1 sector
2 sectors
3 sectors
3 sectors (Y)
only for application with star point
not for Y
Tap selector size
not for multiple coarse tap selector
10
12
14
16
18
22
10
Number of maximum
12
operating positions
without change-over selector
14
16
18
22
10
Number of maximum
12
operating positions
14
with change-over selector
16
(reversing change-over
selector or coarse change18
10
Number of maximum
12
operating positions
with multiple coarse tap
14
selector
16
18
No center position (without change-over
Center positions
selector)
1 center position
3 center positions
reversing change-over selector
Change-over selector
coarse change-over selector
tie-in resistor
Tie-in measures
(tie-in resistor and/or
potential switch
potential switch attached)
potential switch with tie-in resistor
Division
Figure 1
M
I
II
III
350
500
600
800
1200
1500
1
2
3
0
Y
72,5
123
170
245
300
B
C
D
DE
10
12
14
16
18
22
10
12
14
16
18
22
19
23
27
31
35
59
71
83
95
107
0
1
3
W
G
R
S
P
Description of type designation
Operating Instructions BA 050/03 OILTAP®M
050/03/01/0
1
1
1.2
General
Summary of technical data
On-load tap-changer
M III 350 Y
M III 500 Y1)
M III 600 Y
M I 351 M I 5011) M I 601 M I 802 M I 1203 M I 1503
Number of phases and
3 (star point) 3 (star point) 3 (star point)
1
1
1
1
1
1
application
Max. rated through350
500
600
350
500
600
800
1200
1500
current IUm (A)
Rated short-time current
6
8
8
6
8
8
16
24
24
(kA)
Rated short-circuit
3
3
3
3
3
3
3
3
3
duration (s)
Rated short-circuit current
15
20
20
15
20
20
40
60
60
(kA)
Max. rated step voltage
3300
3300
3300
3300
3300
3300
3300
3300
3300
Uim (V)2)
1000
1400
1500
1000
14003) 15003) 20003)
3100
3500
Step capacity (P StN) (kVA)
1) Only for mains operation!
2) The max. rated step voltage may be exceeded by up to 10% following overexcitation of the transformer, provided the step capacity is
not exceeded.
3) Special types with higher step capacities are available
Table 1
For all on-load tap-changer versions
50...60
Rated frequency (in Hz)
without change-over selector: max. 18 with change-over selector: max.
Operating positions
Rated insulation level
Maximum equipment voltage Um
72,5
123
170
245
3005)
(kV)4)
Maximum operating voltage Ub (phase- 55
79
145
170
245
phase) at the diverter switch (kV)
Rated lightning impulse withstand
voltage (kV, 1,2⏐ 50)
Rated switching impulse voltage (kV)
Rated power-frequency withstand
voltage (kV, 50 Hz, 1 min)
Rated withstand voltages of the
internal insulation
Oil compartment
Oil suction pipe
Temperature range
350
550
750
1050
1050
140
230
325
460
850
460
see Table 3
pressure-tight up to 0.3 bar continuous differential pressure (test pressure
0.6 bar)
standard equipment (for details see BA 18)
The OILTAP® M on-load tap-changer can be operated in the rated load
range for oil temperatures between – 25 °C and + 105 °C.
Instructions for operation under arctic conditions can be found in the
general technical data document TD 61.
4) According to VDE 0111 part 1: rms value of the conductor-conductor voltage for which the insulation of a
component is dimensioned.
5) The three-phase on-load tap-changer versions M III 350 Y, M III 500 Y, M III 600 Y are not with available an
equipment voltage of Um=300 kV.
Table 2
050/03/01/0
2
1
General
On-load tapchanger
Weight (kg) approx.
M III 350 Y
M III 500 Y
M III 600 Y
265
M I 351
M I 501
M I 601
240
M I 802
M I 1203
M I 1503
without change250
260
over selector
with change-over
280
260
270
285
selector
Displacement volume (dm³)
72.5 kV
200
190
195
200
approx.
123 kV
225
215
220
225
170 kV
245
235
240
245
245 kV
265
255
260
265
300 kV
285
265
280
285
72.5 kV
130
Oil capacity VS and minimum
123 kV
150
volume DV6) of the diverter
170 kV
170
switch oil compartment (dm³)
245 kV
190
300 kV
210
6) Minimum volume of the oil conservator for oil temperature υ = -30°C...+100°C: DV = 0.1 VS + 4 (dm³)
Table 3
050/03/01/0
3
1
1.3
Figure 2
General
Overview of on-load tap-changer models
Overview of on-load tap-changer models (8997401D)
050/03/01/0
4
1
Figure 3
General
Overview of basic wiring diagrams with identification of tap selector terminals according to MR standard
(8906164D_1)
The contact designations correspond to the data in the dimensional drawings for the on-load tap-changers.
050/03/01/0
5
1
Figure 4
General
(8906164D_2)
050/03/01/0
6
1
Figure 5
General
(8906164D_3)
050/03/01/0
7
1
1.4
Figure 6
General
Examples of wiring diagrams used in practice (contact designation according to MR standard)
Example: On-load tap-changer M III 350/500/600 Y, basic wiring diagram 10 19 1 W
050/03/01/0
8
1
Figure 7
General
Example: On-load tap-changer M III 350/500/600 Y, basic wiring diagram 10 19 3 W
050/03/01/0
9
1
Figure 8
General
Example: On-load tap-changer M I 802, basic wiring diagram 14 27 1 G
050/03/01/0
10
1
Figure 9
General
Example: On-load tap-changer M I 1203/1503, basic wiring diagram 18 35 1 W
050/03/01/0
11
1
1.5
General
Example wiring diagram for OILTAP®M, multiple coarse tap selector design
Figure 10
Example: On-load tap-changer M I 802, basic wiring diagram 16 79 1 G
050/03/01/0
12
2
Technical data
2
Technical data
2.1
Rated through-current (Iu), rated step voltage (Ui), and step capacity (PStN)
On-load tapchanger
I u (A)
Ui (V)
PStN (kVA)
Table 4
Figure 11
M III 350 Y
M III 500 Y
M III 600 Y
M I 802
M I 351
M I 501
M I 601
300
350
395
500
500
600
610
3300
2860
3300
2800
2800
2500
3300
1000
1000
1300
1400
1400
1500
2000
M I 1203
800
2500
2000
940
3300
3100
M I 1503
1200
2580
3100
1200
2580
3100
1500
2340
3500
Rated through-currents (Iu), associated rated step voltages (Ui), and step capacities (PStN), upper and lower
corner point of the step voltage curve (see Figure 11)
Step capacities (rated step voltages Ui, rated through-currents Iu) (8997520D)
050/03/01/0
13
2
2.2
Technical data
Contact life
The expected mean contact life of the arc-carrying diverter switch contacts can be estimated according to Fig. 8, depending on
the relative load (Iu/Ium). Only approximate data can be provided, since the actual contact life is influenced by a wide range of
operational factors (this does not apply to constant-current operation).
The inspection instructions must be followed.
Figure 12
Expected mean contact life with average load
n: number of operations
Iu: Rated through-current
Ium: Max. rated through-current
050/03/01/0
14
2
2.3
Technical data
Rated withstand voltages of the internal insulation
Figure 13 shows the voltage stresses at the tap winding for the three main basic connection types for three-pole on-load tapchangers and single-pole on-load tap-changers. When selecting an on-load tap-changer the maximum load at the tap selector
must be verified in order to avoid the associated rated withstand voltages being exceed.
Without change-over selector
With coarse tap selector in (+) - position
With reversing switch
With coarse tap selector in (-) - position
• a0 = between selected and preset diverter switch tapping.
CAUTION
The maximum rated lightning
withstand impulse voltage
loads at a0 in the center position must be taken into account!
• a1 = between fine tap selector contacts of the winding for one step (closed or open)
• a = between start and end of a fine tap changer winding; for versions with coarse tap changer winding also between
start and end of a coarse tap changer winding.
Note for coarse tapping in (-) position of the change-over selector:
For loads involving impulse voltage the permitted withstand voltage "a" between the end of a coarse tap changer winding connected to fine tap selector contact K and the fine tap selector contact at the end of the fine tap changer winding of the same phase must be taken into account.
• b = between the fine tap selector contacts for different phases and between change-over selector contacts for different
phases connected to the start / end of a fine tap changer winding or a fine tap selector contact.
• f = between diverter switch lead and ground
Additionally for coarse tapping in ( + ) position of the change-over selector:
• c1 = from a ( - ) change-over selector contact to the lead for the same phase.
• c2 = between ( - ) change-over selector contacts for different phases.
Figure 13
On-load tap-changer M III 350 Y ... M I 1503, specific voltage stresses at the tap winding (rated withstand
voltages) (8997560D)
050/03/01/0
15
2
Technical data
Insulation distances Tap selector size B
Tap selector size C
Tap selector size D
kV
1,2I50
kV
kV
kV
kV
kV
50 Hz
1,2I50
50 Hz
1,2I50
50 Hz
1 min.
1 min.
1 min.
a0
90
20
90
20
90
20
a1
150
30
150
30
150
30
a
265
50
350
82
490
105
b1)
265
50
350
82
490
146
c1
485
143
545
178
590
208
c21)
495
150
550
182
590
225
1) Insulation distance not applicable for single-pole on-load tap-changers
Table 5
Tap selector size DE
kV
1,2I50
90
150
550
550
660
660
kV
50 Hz
1 min.
20
30
120
160
230
250
On-load tap-changer M III 350 Y ... M I 1503, rated withstand voltages of the internal on-load tap-changer
insulation
The permissible maximum operating voltage at the individual tap selector sections corresponds to half the value of the rated AC
withstand voltages listed in Table 5.
without change-over selector
with reversing change-over selector
with coarse tap selector
p-change configurat tap selector size -change configurat tap selector size -change configurat tap selector size
10050
B/C/D/DE
10071W
B/C/D/DE
10071G
B/C/D/DE
10060
B/C/D/DE
10081W
B/C/D/DE
10081G
B/C/D/DE
10070
B/C/D/DE
10091W
B/C/D/DE
10091G
B/C/D/DE
10080
B/C/D/DE
12101W
B/C/D/DE
12101G
B/C/D/DE
10090
B/C/D/DE
12111W
B/C
12111G
B/C
10100
B/C/D/DE
14111W
D/DE
14111G
D/DE
12110
B/C/D/DE
14121W
B/C
14121G
B/C
12120
B/C/D/DE
14131W
B/C
14131G
B/C
14130
B/C/D/DE
16121W
D/DE
16121G
D/DE
14140
B/C/D/DE
16131W
D/DE
16131G
D/DE
16150
B/C/D/DE
16141W
B/C/D/DE
16141G
B/C/D/DE
16160
B/C/D/DE
16151W
B/C
16151G
B/C
18170
B/C/D/DE
18151W
D/DE
18151G
D/DE
18180
B/C/D/DE
18161W
B/C
18161G
B/C
22190
B/C/D/DE
18171W
B/C
18171G
B/C
22200
B/C/D/DE
10191W
B/C/D/DE
10191G
B/C/D/DE
22210
B/C
12231W
B/C/D/DE
12231G
B/C/D/DE
22220
B/C
14271W
B/C/D/DE
14271G
B/C/D/DE
16311W
B/C/D/DE
16311G
B/C/D/DE
18351W
B/C/D/DE
18351G
B/C/D/DE
Table 6
Possible configurations (also possible as 3 W, 3 G)
050/03/01/0
16
2
2.4
Technical data
On-load tap-changer OILTAP®M III 600 Y ... M I 1503 with coarse tap selector (up to 5 coarse taps)
Fine voltage regulation requires a large number of operating positions that may necessitate
a multiple coarse tapping arrangement.
For example, with a 5-stage coarse winding and a fine tap changer winding with 18 tappings,
107 operating positions can be achieved.
The coarse tap selector is attached to both sides of the fine tap selector.
The on-load tap-changers are available for Um = 72.5 ... 300 kV and for 2 ... 5 coarse taps (tap selector size B, C and D).
Multiple coarse tap selector
• a0 = between selected and preset diverter switch tapping
• a1 = between fine tap selector contacts of the winding for
one step (closed or open)
• a = between start and end of a fine tap changer winding and
between the closed K-contact and any points of the fine tap
changer winding for the same phase
• b = between the fine tap selector contacts for different phases and between the closed K-contact of a phase and any
points of the fine tap changer winding for another phase
• c1 = between any coarse tappings for a phase and the diverter switch lead for the same phase
• c2 = between corresponding open coarse tappings for different phases
• d1 = between closed and adjacent coarse change-over selector contact in a phase
• d2 = between open adjacent coarse change-over selector
contacts in a phase
• d3 = between start and end of all coarse taps in a phase
• f = between diverter switch lead and ground
Figure 14
Designation and definition of the insulation distances (8997940D)
Tap selector size B
Tap selector size C
Tap selector size D
Insulation distances
kV
1,2I50
kV
kV
kV
50 Hz
1,2I50
50 Hz
1 min.
1 min.
a0
90
20
90
20
a1
150
30
150
30
a
265
50
350
82
b1)
265
50
350
82
c1
455
127
525
165
c21)
455
127
525
165
d1
265
50
350
82
d2
350
82
450
105
d3
350
82
450
105
1) Insulation distance not applicable for single-pole on-load tap-changers
Figure 15
kV
1,2I50
90
150
450
450
590
590
450
450
490
kV
50 Hz
1 min.
20
30
105
146
210
215
105
105
120
On-load tap-changer OILTAP®M with multiple coarse tap selector, rated withstand voltages of the internal
on-load tap-changer insulation
050/03/01/0
17
3
Special types
3
Special types
3.1
Parallel bridges for parallel connection of tap selector planes
Only for on-load tap-changer OILTAP®M I 802 (803), M I 1203/1503 (see section 3, drawing no. 899598)
For current division at the terminal contacts of the tap selector associated tap selector planes are connected in parallel, i.e.
• 2 tap selector planes for on-load tap-changer M I 802 (803),
• 3 tap selector planes for on-load tap-changer M I 1203 / 1503.
Parallel bridges at the tap selector terminals are required if the tap winding is wound in two or more strands and each of these
strands taps into terminal contacts of the tap selector.
This measure reliably prevents
a) carry-over of compensating currents into the tap selector and diverter switch circuits
b) arc occurring during commutation at moved tap selector contact bridges
c) overvoltages between adjacent tap selector terminals connected in parallel
3.2
On-load tap-changer OILTAP®M I 603 and M I 803 with 3-sector diverter switch
On-load tap-changer models M I 603 and M I 803 @@ are supplied with a 3-sector diverter switch, if required.
This results in a higher step capacity (see Fig. 10) and/or a higher contact life of the arc-carrying diverter switch contacts.
Figure 16
Step capacity (rated step voltages Ui and rated through-currents Iu) for on-load tap-changer M I 603 and
M I 803 (8904804D)
050/03/01/0
18
3
3.3
Special types
On-load tap-changer OILTAP®M I 502 and M II 502 for 16 2/3 Hz
On-load tap-changer models M I 502 (single-pole on-load tap-changer for single-phase transformers in any configuration) and
M II 502 (two-pole on-load tap-changer for single-phase transformers with center-tap connection) are available for application
in traction supply transformers with an operating frequency of 16 2/3 Hz. The on-load tap-changers are equipped with a special
diverter switch. The tap change operation sequence and the dimensioning of the transition resistors are adapted to an operating
frequency of 16 2/3 Hz (technical data are available on request).
3.4
Two-pole on-load tap-changer OILTAP®M II 352/502/602
On-load tap-changer M II 352/502/602 is available as a two-pole on-load tap-changer for single-phase center-tap connection
with technical specifications corresponding to on-load tap-changer M III 350 Y, M III 500 Y or M III 600 Y (see dimensional drawings, section 4).
On-load tap-changer combination for delta connection (example)
On-load tap-changer M II 352 can also be used in conjunction with single-pole on-load tap-changer M I 351 as a two-column
on-load tap-changer combination (M I 351/M II 352) for voltage regulation of transformer windings with delta connection (correspondingly with M I 501/M II 502 and M I 601/M II 602). This combination is referred to as M III K, see Figure 17.
The tap windings must be based on Figure 17.
Figure 17
3.5
On-load tap-changer combination M III K for delta connection: M I 351/M II 352 (a - M I 351, b - M II 352)
On-load tap-changer OILTAP®M III 350 Y...M I 1503 for linear voltage regulation, up to 34 operating positions
The high number of operating positions is achieved without change-over selectors through doubling of the tap selector contact
planes compared with the standard version (leading to extended installation length).
The on-load tap-changers are available for Um = 72.5 ... 300 kV and several tap selector sizes (rated withstand voltages and dimensional drawings are available on request).
050/03/01/0
19
4
Annex
4
Annex
4.1
OILTAP®M III 350/500/600 Y-0/W/G (8997102E)
050/03/01/0
20
4
4.2
Annex
OILTAP®M II 352/502/602-0/W/G (8997112E)
050/03/01/0
21
4
4.3
Annex
OILTAP®M I 351/501/601-0/W/G (8980025E)
050/03/01/0
22
4
4.4
Annex
OILTAP®M I 802-0/W/G (8997122E)
050/03/01/0
23
4
4.5
Annex
OILTAP®M I 1203/1503-0/W/G (8997132E)
050/03/01/0
24
4
4.6
Annex
OILTAP®M III K - 0/W/G (7275470E)
050/03/01/0
25
4
4.7
Annex
OILTAP®M III 600 Y with multiple coarse tap selector (8995943E)
050/03/01/0
26
4
4.8
Annex
OILTAP®M I 601 with multiple coarse tap selector (8995913E)
050/03/01/0
27
4
4.9
Annex
OILTAP®M I 802 with multiple coarse tap selector (8995923E)
050/03/01/0
28
4
4.10
Annex
OILTAP®M I 1203/1503 with multiple coarse tap selector (8995933E)
050/03/01/0
29
4
4.11
Annex
OILTAP®M I 351...1503, RM I 601...1502 - tie-in resistors with/without potential switch (8986902E)
050/03/01/0
30
4
4.12
Annex
OILTAP®M II - tie-in resistors with/without potential switch (8986912E)
050/03/01/0
31
4
4.13
Annex
OILTAP®M III Y, RM III Y - tie-in resistors with/without potential switch (8986922E)
050/03/01/0
32
4
4.14
Annex
OILTAP®M I 351...1503, RM I 601...1502 - ins. cylinder with potential switch without tie-in resistor (8988043E)
050/03/01/0
33
4
4.15
Annex
Supplementary drawings for on-load tap-changers (8980125E)
050/03/01/0
34
4
4.16
Annex
OILTAP®M - installation drawing for centric drive unit (893978BE, sheet 1)
050/03/01/0
35
4
4.17
Annex
OILTAP®M - installation drawing for centric drive unit (893978BE, sheet 2)
050/03/01/0
36
4
4.18
Annex
On-load tap-changer head, centric drive unit (893899CE)
050/03/01/0
37
4
4.19
Annex
OILTAP®M, MS, R, RM - on-load tap-changer head versions (7200261E)
050/03/01/0
38
4
4.20
Annex
OILTAP®M, MS, R, RM - swivelling range of the gear unit (7200272E)
050/03/01/0
39
4
4.21
Annex
OILTAP®M - oil compartment contact screening (7303360E)
050/03/01/0
40
4
4.22
Annex
Tap selector contact arrangement - no. of contacts per plane 10...22 (8980133E)
050/03/01/0
41
4
4.23
Annex
Mounting position of the tap selector terminals (8904778E)
050/03/01/0
42
4
4.24
Annex
OILTAP®M, RM, VACUTAP®VRC/VRE - connection cables 3W, 1G, 3G (7235901E)
050/03/01/0
43
4
4.25
Annex
OILTAP®M and VACUTAP®VRC/VRE - fine tap selector and change-over selector screening (7303350E)
050/03/01/0
44
4
4.26
Annex
OILTAP®M I 802/8031203/1503 - bridges for parallel connection of tap selector terminals (8995981E)
050/03/01/0
45
4
4.27
Annex
OILTAP®M, MS, RM - horizontal drive shaft, centric drive unit (8938968E)
050/03/01/0
46
4
4.28
Annex
OILTAP®M III 350/500/600 Y - tap selector winding (8911073E)
050/03/01/0
47
4
4.29
Annex
OILTAP®M I 351/501/601 - tap selector winding (8911086E)
050/03/01/0
48
4
4.30
Annex
OILTAP®M I 1203/1503 - tap selector winding (8911094E)
050/03/01/0
49
4
4.31
Annex
OILTAP®M I 802 (8911103E) - tap selector winding
050/03/01/0
50
4
4.32
Annex
Special version for bell-type tank installation (8967629E)
050/03/01/0
51
4
4.33
Annex
OILTAP®M, MS, R, RM with flange for pressure relief valve (8951686E)
050/03/01/0
52
4
4.34
Annex
Tap selector bottom with additional screening - reversing change-over selector version (8939341E)
050/03/01/0
53
4
4.35
Annex
Tap selector bottom with additional screening - coarse change-over selector version (8939351E)
050/03/01/0
54
4
4.36
Annex
Tap selector bottom with hole D20 and D13 (7256491E)
050/03/01/0
55
www.reinhausen.com
©Maschinenfabrik Reinhausen GmbH
Falkensteinstraße 8
93059 Regensburg
Telefon:
Telefax:
E-Mail:
+49 (0)941 4090 0
+49 (0)941 4090 111
[email protected]
TD 050/03 en • 0108/500 • 050/03/01/0 • F0018602 • Printed in Germany

OILTAP® M Technical Data (TD 050/03)

Transcription

Similar documents

Setup Exchange on iOS

tomfooleries.com

IDEAL STANDARD - MOMENTS VANITY BASIN

VALENCIA 2 Y100

Instructions for BarryUWireless for Students (iPhone/iPod)

DP3000SA - Durapower

Introducing the

Mobile claims instructions

certificate - Dietze + Schell