OCTG Product Selection Guide

OCTG product selection guide
VAM ® connections
OCTG grades
2010 Edition
product line
Products
VAM® 21
VAM® TOP
VAM® TOP HC
VAM® TOP HT
VAM® HP
VAM® HW-ST
VAM® SLIJ-II
VAM® FJL
VAM® HTF
VAM® HTT
DINO VAM®
DWC
BIG OMEGA™
VAM® SW
VAM® MUST
The leading set of premium Integral and Threaded and Coupled connections for a comprehensive coverage of the Oil & Gas industry needs in
OCTG worldwide.
Check out the product summary table below and connection selection guideline inside to find out what connection will best fit your need.
Each year VAM® design many new connections, extend product lines and qualify new sizes to the most stringent specifications to meet our
customer needs.
Besides standard developments, VAM® Research & Development teams can customize connection designs to new sizes or specific requirements.
Type
T&C
T&C
T&C
T&C
T&C
T&C
Semi-Flush
Flush
Flush
Integral on
upset
T&C
T&C
T&C
T&C
Flush
Main
Applications
Size Range (in)
5
14(a)
Class
Premium
ISO CAL equivalence
IV
Production
High
compression
High
torque
HPHT
HPHT
Clearance
Max
clearance
-
-
-
-
-
-
-
Tubing
Liner
Tie-Back
Casing
Tubing
Liner
Tie-back
Casing
Liner
Tie-back
Casing
Liner
Tie-Back
Casing
Liner
Casing
Liner
Tie-Back
Casing
High
High
Torque
Torque
Max
Tubing
clearance
Drilling Drilling w
Tubing
Liner
Workstrings
DST
Fast
running
Drilling
with
Casing
Large OD
Steam
Well
High
collapse
Salt dome
-
-
-
-
-
Tubing
Casing
Casing
Surface
casing
Casing
2 3/8
4½
5
16
5
7¾
4½
7
7 5/8
10 ¾
5
14
4½
16
2 3/8
11 7/8
4½
9 5/8
2 7/8
5½
9 5/8
16
3½
13 3/8
14
26
5½
13 3/8
7 5/8
10 3/4
Premium
IV
Premium
II to IV
Premium
IV
Premium
IV
Premium
IV
Premium
II
Premium
II to III
Premium
N/A
Premium
IV
Premium
IV
semi
Premium
semi
Premium
semi
Premium
Premium
N/A
Premium
N/A
100%
100%
100%
100%(d)
100%
100%
Internal Pressure
(%Pipe Body)
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
External Pressure
(%Pipe Body)
100%
100%
100%
100%
100%
100%
70%
100%
100%
100%
100%
100%
Same
as
BTC
Tension Efficiency
(%Pipe Body)
100%
100%
100%
100%
100%
100%
100%
68-82%
45-69%
59-64%
100%
100%
95%
100%
100%
56-58%
Compression
(%Pipe Body)
100%
100%
60%(b)
100%
80%(b)
60%
40%(b)
35-39%
60%(b)
up to
50%(c)
50%
up to
70%(c)
100%
56-58%(b)
T&C: Threaded and coupled
a - Contact VAM® for size availability of VAM® 21
b - Compression ratings are calculated to retain gas sealability in all domains of the
performance envelope. Structural compression ratings are higher.
48-58%(b) 18-28%(b)
c - Depends on the internal or external pressure level
d - depends on size and combined loads
Dope free solution
CLEANWELL® DRY is the VAM® Family “Dope Free”solution:
• It is a fully DRY and non sticky multi function coating directly applied in Vallourec mills on the surface
of threads such as VAM® TOP.
• Coating replaces both storage and running compounds, which allow optimizing rig preparation by reducing the occurrence
of protector removal, thread cleaning and pipe handling.
CLEANWELL® DRY brings a wide range of benefits
• No discharge to the environment
• Anti-corrosion properties equivalent to storage dope
• Not sticky and easy thread inspection
• Prevent Rig thread cleaning, minimize yard and rig handling
• Prevent plugging formation pores
Box and Pin threads with CLEANWELL® DRY
VAM® and CLEANWELL® are registered Trademarks of Vallourec Oil and Gas France.
connection for your application
How does it work?
Examples:
®
Premium connections - Gas tight performance
STANDARD CLEARANCE
Production
VAM® FJL
VAM® HTF
VAM® HTT
5
5
5
7 5/8
5
4 1/2
2 3/8
4 1/2
2 7/8
4 1/2
16
7 3/4
7
10 3/4
14
16
11 7/8
9 5/8
5 1/2
High Compression (>60% CYS)
Main application
High bending
Regular
LINER
Production
High Compression (>60% CYS)
ISO CAL IV
High Deviation & Rotating Liner
High Torque
Regular
Production casing
High Compression (>60% CYS)
Production Tie-back
ISO CAL IV
CASING
Rotating casing
High torque
Premium Gas tight
Intermediate Casing
Semi-Premium - Fast Running
Surface casing / Conductor
Fast Running
Production Tubing
CAL IV
Production Liner
High Compression + ISO CAL IV
HPHT
Contingency Drilling Liner
Clearance + ISO CAL III
&
Rotating Liner and Casing
High Torque + ISO CAL IV
DEEP WELLS
Production casing
Heavy Wall
Production Tie-back
Heavy Wall + HEP(1)+ISO CAL IV
Intermediate Casing
High Compression + HEP(1) + ISO CAL IV
Workstring, Test string
HIGH TORQUE
Drilling with Tubing
High Torque
Drilling with Casing / Liner
High Torque
APPLICATIONS
Water Injection
Injection Wells
SPECIAL
APPLICATIONS
Steam Injection / Heavy oil
Salt Dome & Squeezing clay
HEP(1)
Expandable
Inner
Production
Outer / Single barrier
RISER
Drilling (Surface BOP) riser
Workover / Landing string
1: High External Pressure
2: Contact VAM® for size availability of VAM® 21
VAM® HP
2 3/8
14
VAM® TOP
5(2)
range (in)
ISO CAL IV
High Deviation
In te g ral J oi n t (IJ )
Size
Regular
TUBING
MAX CLEARANCE
Threaded and coupled (T&C)
VAM® SLIJ-II
Technical requirements
In case of multiple choice and for more details, contact your
VAM® representative or go to www.vamservices.com
VAM® HWST
Sub application
• 2: I need a 7” Liner with good clearance and high compression
capacity  VAM® SLIJ-II.
I might need to rotate it so I really need high torque capacity
 VAM® HTF offers high torque and has some capacity
in compression.
VAM® TOP HT
Applications
• 1: I need a 9 5/8” production casing qualified to ISO CAL IV
 VAM® 21 for highest strength, VAM® HTF for max
clearance.
VAM® TOP HC
The connection selection table below helps you choosing the VAM
connection that best fits your needs. It is read horizontally and works as
follow:
• 1: Select you application and technical requirements
• 2: Look at the corresponding colored boxes to determine the
connection that best fits the application and requirements, with the
following color code:
Dedicated - The connection has been designed and qualified
for this application and technical requirements
Capable or compatible - The connection will offer some
capacity but finer evaluation is needed (ex: capacity may be limited
or overdesigned for the application; availability may be limited to
few sizes). Check with your VAM® representative.
Not applicable.
• 3: For the recommended connections (green cells):
- Check your need for clearance: T&C for standard clearance, T&C
with Special Clearance option for intermediate clearance,
flush/semi-flush for maximum clearance.
- Check the size you need versus the available size range per connection
VAM® 21
The right
THREADED & COUPLED
Example of casing design (HPHT well) with VAM® solutions
from top to bottom
Connection OD > Pipe OD
Standard:
Compression
• VAM ® 21
Tension
Connection
• VAM ® TOP series
Internal
Pressure
Pipe
• VAM ® HWST
• DINO VAM ®
Surface
Casing
20" 133# k55
BIG OMEGA
• DWC
• BIG OMEGA ™
• VAM ® SW
External
Pressure
Slim line:
10 3/4" 110.2# VM110SS
VAM® HP SC80
Production
Casing
Contingency
Tie-back
7 5/8" 42.7# VM110SS
VAM® HP
• Special Clearance
option
T&C connection typical envelope
CYS(3) = 100% PBYS(4)
• VAM ® HP
T&C connections generally offer maximum strength but require
connection OD larger than pipe OD (standard clearance).
Special Clearance (SC) option improves clearance while reducing
tensile strength.
SEMI-FLUSH
Connection OD ≈ 102% Pipe OD
13 5/8" 88.2# VM125CY
VAM® 21
Intermediate Casing
• VAM ® SLIJ-II
Compression
Tension
Connection
Internal
Pressure
Pipe
9 7/8" 66.9# VM125SS
VAM® 21
Production casing
Semi-Premium
SEMI-FLUSH connection typical envelope
70% ≤ CYS(3) ≤ 82% PBYS(4)
SEMI-FLUSH connections combine great clearance and high
strength.
4 1/2"
18.7# Q125
VAM® TOP
Production Liner
FLUSH
Expandable
4 1/2
T&C
IJ
IJ
• VAM ® FJL
7
6 5/8
9 5/8
7 5/8
16
14
13 3/8
VAM© DPR HP
VAM© DPR SR
7 5/8
Riser
T&C
VAM© PDW1
4 1/2
13 3/8 10 3/4 11 3/4
T&C
VAM© TOP FE
IJ
VAM© TTR
IJ
Connection OD ≈ 100% Pipe OD
VAM® ET MOD
Special
T&C
VAM® ET WISE
26
VAM® MUST
14
13 3/8
External
Pressure
7 5/8"
39# Q125
VAM® SLIJ-II
Contingency
drilling Liner
VAM® SW
3 1/2
16
DINO VAM®
9 5/8
7" 42.7# VM125CY
VAM® TOP HC
Contingency
Tie-back
(T&C)
BIG OMEGA
(T&C)
DWC
(T&C)
Compression
• VAM ® HTF
• VAM MUST
®
Tension
Connection
Pipe
Internal
Pressure
6 5/8
External
Pressure
FLUSH connection typical envelope
45% < CYS(3) < 70% PBYS(4)
FLUSH connections offer maximum clearance while reducing
strength.
3: CYS = Connection Yield Strength
4: PBYS = Pipe Body Yield Strength
A full range of OCTG grades for all your applications
How does it work?
Highly Corrosive Application ( CO2 + H2S + Chlorides)
pCO2
235°C
455°F
This material selection chart helps you choosing the appropriate
material for your application depending on H2S and CO2 partial
pressures, and temperature range in your well.
API vs proprietary grades
Super 13% Cr
1500 psi
10 MPa
Vallourec proprietary grades offer solutions for grades not covered by
API 5CT (ex: 125 ksi sour service).
They also offer greater performances (ex: High Collapse grades) and
higher reliability (ex: Sour Service grades) thanks to stringent
internal requirements in quality and process control, mechanical
properties and material testing.
FerriticAustenitic
grades
180°C
356°F
150°C
300°F
2 psi
0.05 psi
0.013 MPa
0.0003 MPa
Carbon Steel
o psi
200°C
390°F
High Alloy
materials
Austenitic grades
Ni-based Alloys
Duplex
or
Super Duplex
13% Cr
Need more details ?
Contact your Vallourec representative for finer material recommendations.
Free S
Sweet Corrosive
application
any CI-
1.5 psi
15 psi
0.01 MPa
0.1 MPa
pH2S
Carbon Steel with Sour Service Performances
Standard, HPHT,
Deep Well, HC, LT
applications
Sour Service, High Collapse and Sour Service application
STANDARD : API 5CT Grades
From K55 to Q125, Vallourec can supply the full range of API 5CT grades including Chromium martensitic steels. All Product Specification Levels
(PSL) and Special Requirements (SR) from API 5CT can be delivered, with PSL 2 standardized on all quenched and tempered grades.
In addition and upon request, Vallourec can customize production to meet customers’special requirements such as PSL 3, restricted tolerances,
non standard pipe sizes and walls, CTOD requirement…
HIGH PRESSURE HIGH TEMPERATURE
HPHT grades to be used where high strength is required with limited resistance to sour service conditions within the guidelines of NACE MR0175.
Name
YS range
(ksi-Mpa)
UTS min
(ksi-Mpa)
HRC value
Operating temperature for use
in sour service conditions acc. to NACE
Q 125*
125 (862) - 150 (1034)
135 (931)
No limit
≥ 225°F (107°c)
VM 125 CY
125 (862) - 140 (965)
135 (931)
≤ 35
≥ 175°F (80°c)
VM 130 CY
130 (896) - 140 (965)
135 (931)
≤ 35
≥ 175°F (80°c)
VM 125 HY
140 (965) - 150 (1034)
145 (1000)
≤ 36
≥ 225°F (107°c)
* API grades
DEEP WELL
Deep well grades to be used where high yield strength is required while maintaining ductility and fracture toughness
Name
YS range
(ksi-Mpa)
UTS min
(ksi-Mpa)
CVN average value min. Full size specimen at 70°F (20°C)
VM 140
140 (965) - 165 (1138)
150 (1034)
38 ft lb (50 J)
VM 150
150 (1034) - 175 (1206)
160 (1104)
30 ft lb (41 J)
HIGH COLLAPSE
High collapse grades for casing to be used in high pressure wells. They offer an average of 30% and up to 40% extra performance over API collapse
rating. As mechanical properties and pipe dimensions are major factors in collapse resistance, the following parameters have been optimised to
guarantee high collapse pressures: D/t ratio, yield strength, ovality, wall thickness, residual stresses.
Name
YS range
(ksi-Mpa)
UTS min
(ksi-Mpa)
VM 80 HC
80 (552) - 110 (758)
100 (690)
VM 95 HC
95 (655) - 125 (862)
110 (758)
VM 110 HC
110 (758) - 140 (965)
125 (862)
VM 125 HC
125 (862) - 150 (1034)
135 (931)
VM 140 HC
140 (965) - 165 (1138)
150 (1034)
Collapse
resistance
minimum guaranteed
collapse pressures are
available on request
Pipe after collapse testing
LOW TEMPERATURE
Low Temperature grades to be used to be used in arctic regions where high impact toughness at subzero temperatures are requested.
Name
Y.S. range
(ksi-MPa)
U.T.S. min.
(ksi-MPa)
VM 55 LT
55 (379) - 80 (552)
75 (517)
30 ft lb (41 J)
CVN average value min. Full size specimen at -50°F (-46°C)
VM 80 LT
80 (552) - 95 (655)
95 (655)
30 ft lb (41 J)
VM 95 LT
95 (655) - 110 (758)
105 (724)
30 ft lb (41 J)
VM 110 LT
110 (758) - 140 (965)
125 (862)
30 ft lb (41 J)
VM 125 LT
125 (862) - 150 (1034)
135 (931)
30 ft lb (41 J)
These average values for Charpy V-Notch absorbed energy have been determined
at -50°F (-46°C) on three full size impact specimens taken transversally when it is
possible, or longitudinally, on pipes and coupling stocks
SOUR SERVICE
Sour service grades for tubing and casing to be used in wells where H2S is present. The threshold stresses guaranteed have been determined
according to method A of NACE TMO177 standard. VM xx SS-D grades are also tested according to method D (DCB test).
Name
YS range
(ksi-Mpa)
UTS min
(ksi-Mpa)
HRC value
Threshold stress
min.
L80 *
80 (552) - 95 (655)
95 (655)
≤ 23
80% SMYS
VM 80 SS
80 (552) - 95 (655)
95 (655)
≤ 22
90% SMYS
C90 *
90 (621) - 105 (724)
100 (690)
≤ 25.4
80% SMYS
VM 90 S
90 (621) - 105 (724)
100 (690)
≤ 24
85% SMYS
VM 90 SS
90 (621) - 105 (724)
100 (690)
≤ 24
90% SMYS
T95 *
95 (655) - 110 (758)
105 (724)
≤ 25.4
80% SMYS
VM 95 S
95 (655) - 110 (758)
105 (724)
≤ 25
85% SMYS
VM 95 SS
95 (655) - 110 (758)
105 (724)
≤ 25
90% SMYS
VM 95 SS-D
95 (655) – 110 (758)
105 (724)
≤ 25
90% SMYS + DCB test
VM 100 SS
100 (690) - 115 (792)
110 (758)
≤ 28
85% SMYS
VM 110 SS
110 (758) - 125 (862)
120 (828)
≤ 30
85% SMYS
VM 110 SS-D
110 (758) – 120 (828)
120 (828)
≤ 30
85% SMYS + DCB test
VM 125 SS
125 (862) – 135 (931)
130 (896)
≤ 34
85% SMYS
(0.03 H2S, pH 3.5)
Sour Gas corrosion
test equipment
* API grades
HIGH COLLAPSE AND SOUR SERVICE GRADES
High collapse and sour service grades for casing to be used in high pressure wells where H2S is present.
YS range
(ksi-Mpa)
Name
UTS min
(ksi-Mpa)
HRC
value
Threshold stress
min.
85% SMYS
VM 80 HCS
80 (552) - 95 (655)
95 (655)
≤ 22
VM 80 HCSS
80 (552) - 95 (655)
95 (655)
≤ 22
90% SMYS
VM 90 HCS
90 (621) - 105 (724)
100 (690)
≤ 24
85% SMYS
VM 90 HCSS
90 (621) - 105 (724)
100 (690)
≤ 24
90% SMYS
VM 95 HCS
95 (655) - 110 (758)
105 (724)
≤ 25
85% SMYS
VM 95 HCSS
95 (655) - 110 (758)
105 (724)
≤ 25
90% SMYS
VM 110 HCSS
110 (758) - 125 (862)
120 (828)
≤ 30
85% SMYS
Collapse
resistance
minimum
guaranteed
collapse
pressures
are available
on request
FEA simulation of Collapse
SWEET CORROSION
Martensitic grades (13Cr and Super 13Cr) to be used in wells with CO2, chlorides and/or some H2S up to 356°F (180°C).
Martensitic and High Collapse grades are also available upon request.
Type
13% Cr
Name
YS range
(ksi-Mpa)
UTS min
(ksi-Mpa)
HRC
value
L80 13Cr*
80 (552) - 95 (655)
95 (655)
≤ 23
VM 80 13CR
80 (552) - 95 (655)
95 (655)
≤ 23
VM 85 13CR
85 (586) - 100 (690)
100 (690)
≤ 24
VM 90 13CR
90 (621) - 105 (725)
100 (690)
≤ 26
VM 95 13CR
95 (655) - 110 (758)
105 (724)
≤ 28
VM 95 13CRSS
95 (655) - 110 (758)
105 (724)
≤ 30
VM 110 13CRSS
110 (758) - 125 (862)
120 (828)
≤ 34
Super 13% Cr
COST
Carbon +
Inhibitors
Chromium
YEARS
Martensitic grades (13Cr/S13Cr) are often the most economical
solution on the long term for sweet corrosion wells
* API grades
HIGHLY CORROSIVE
Ferritic-austenitic grades to be used in wells with CO2, chlorides
and/or some H2S up to 250°C.
Type
Name
YS range
(ksi-Mpa)
UTS min
(ksi-Mpa)
HRC
value
VM 22 65*
65 (450) - 90 (620)
90 (620)
≤ 26
VM 22 110
110 (760) - 140 (965)
115 (795)
≤ 36
VM 22 125
125 (860) - 150 (1035)
130 (900)
≤ 37
VM 22 140
140 (965) - 160 (1105)
145 (1000)
VM 25 75*
75 (520) - 100 (690)
VM 25 125
Austenitic grades to be used in wells where high concentrations of
H2S, CO2 and chlorides are present.
YS range
(ksi-Mpa)
UTS min
(ksi-Mpa)
HRC
value
VM 28 110
110 (760) - 140 (965)
115 (795)
≤ 35
VM 28 125
125 (860) - 150 (1035)
130 (900)
≤ 37
≤ 38
VM 28 135
135 (930)- 155 (1070)
140 (965)
≤ 38
95 (655)
≤ 26
VM 825 110
110 (760) - 135 (930)
115 (795)
≤ 35
125 (860) - 150 (1035)
130 (900)
≤ 37
VM 825 120
120 (830) - 145 (1000)
125 (860)
≤ 37
VM 25 140
140 (965) - 160 (1105)
145 (1000)
≤ 38
VM G3 110
110 (760) - 130 (900)
115 (795)
≤ 35
VM 25S 80*
80 (550) - 105 (725)
105 (725)
≤ 28
VM G3 125
125 (860) - 145 (1000)
130 (900)
≤ 37
VM 25S 125
125 (860) - 150 (1035)
130 (900)
≤ 37
VM G50 110
110 (760) - 130 (900
115 (795)
≤ 35
VM 25S 140
140 (965) - 160 (1105)
145 (1000)
≤ 38
VM G50 125
125 (860) - 145 (1000)
130 (900)
≤ 37
Duplex
Super duplex
Type
Super Austenitic
Nickel
Base Alloys
Name
* solution annealed grades, higher grades are obtained by cold working.
SPECIAL Applications (RISER – EXPANDABLE)
Riser grades from 95 to 125 ksi to be used on high fatigue riser applications (available with Sour Service resistance): VM 95 R to VM 125 R.
Expandable grades from 50 to 80 ksi to be used on expandable tubular applications: VM 50 ET, VM 80 ET, VM 80 13ET.
OCTG grades
Vallourec offers a full range of standard API and proprietary grades covering all the needs of the OCTG industry. From standard applications
to the most severe environments, Vallourec is your worldwide guarantee for quality and reliability.
Check out the grade summary table below and material selection chart inside to find out what grade will best fit your need.
Vallourec proprietary grades
S
API Grades
VM xx CY
VM xx HY
VM 140
VM150
VM xx LT
VM xx HC
VM xx S
VM xx SS
VM xx SS-D
VM xx HCS
VM xx HCSS
VM xx 13CR
VM xx 13CRSS
Corrosion
Resistant
Alloys
(CRA)
Type
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Martensitic
(13%Cr &
Super 13%Cr)
Ferritic-Austenitic
& Austenitic
Application
Standard
HPHT
Deep Well
Low Temperature
High Collapse
Sour Service
High Collapse &
Sour Service
Sweet Corrosion
Highly Corrosive
Yield Strength
ksi (MPa)
< 80
H40 – J55 – K55 –
M65
VM 55 LT
80
(552)
N80 – L80
VM 80 LT
85 (586)
90 (621)
C90
95
(655)
C95
T95
G
R
A
D
E
API Grades
110
(758)
VM 95 LT
VM 110 LT
P110
125
(862)
Q125
140 (965)
150 (1034)
VM 125 CY
VM 130 CY
VM 125 HY
VM 125 LT
VM 140
VM 150
VM 22 65
VM 25 75
L80 (API)
VM 80 SS
VM 80 HCS
VM 80 HCSS
L80 13CR (API)
VM 80 13CR
C90 (API)
VM 90 S
VM 90 SS
VM 90 HCS
VM 90 HCSS
VM 85 13CR
VM 90 13CR
VM 95 HC
T95 (API)
VM 95 S
VM 95 SS
VM 95 SS-D
VM 95 HCS
VM 95 HCSS
VM 95 13CR
VM 95 13CRSS
VM 110 HC
VM 110 SS
VM 110 SS-D
VM 80 HC
VM 125 HC
VM 125 SS
VM 110 HCSS
VM 110 CRSS
VM 125 HCSS
VM 22 110
VM 28 110
VM 825 110
VM 825 120
VM G3 110
VM G50 110
VM 22 125
VM 25 125
VM 25S 125
VM 28 125
VM 825 125
VM G3 125
VM G50 125
VM 22 140
VM 25 140
VM 25S 140
VM 28 135
VM 140 HC
Full range of products
VM 25S 80
Integrated pipe manufacturer
• Size range : 2 3/8’’to 26’’for OCTG
• Design, process and control of proprietary steel chemistries
• Grades for all OCTG needs: API and Vallourec proprietary grades in
carbon, 13%Cr, Super 13%Cr, Sour Service, High collapse, CRA…
• Steel mills in France, Germany, USA, Brazil and several
pipe mills throughout the world dedicated to the
production of OCTG products
• Tailor made products: non standard sizes and walls, restricted
tolerances, heavy wall…
• Supply of casing and completion accessories: pup joints, couplings,
crossovers, lifting plugs, blast joints, mule shoes, nipples, oriented
couplings… and many more
Quality
• Vallourec has adopted a company-wide Total Quality Management
(TQM) system to provide the best possible service to customers.
Led by general management and coordinated by management teams,
TQM focuses on continuous improvement programs giving priority to
control over process fluctuations and efficiency gains.
Health, safety and environment has been considered as the very first
priority for Vallourec and our policy is to get ISO 14001 accreditation
in all our plants.
• In house metallurgical testing and Non-Destructive
Examination
• OCTG threading integrated to the pipe mills or
strategically located to serve a market
Expertise and know-how
• Vallourec can help you selecting the most appropriate
grade for your application, based on many existing test
data and field experience gained thru years of services
for the Oil & Gas industry.
• For specific and critical well conditions, fit-for-purpose
tests can be carried out at Vallourec Research Centres to
minimize your risk and optimize your well development
World Leader in Premium Tubular Solution
E
Europe
urope
America
a
North Americ
Sou
South
th America
America
Asia
Asia and
and M
Middle
iddle E
East
ast
Africa
Afri
ca
Sales Offices
Steel Plants
Manufacturing Plants
Accessories
Accessories aand
nd Repair
Repair VAM
VAM® L
Licensee
icensee Facilities
Facilities
OFFICES
SALES & SERVICES OFFICE
S
FRANCEE
VALLOUREC OIL AND GAS FRANC
B
oulogne B
illancourt - FFrance
rance
Boulogne
Billancourt
Ph
one +
33 1 4909373
Phone
+33
490937311
[email protected]
[email protected]
VALLOUR
VALLOUREC
EC DE
DEUTSCHLAND
UTSCHLAND Gmb
GmbH
H
Düss
eldorf - Ge
rmany
Düsseldorf
Germany
Ph
one +
49 211 960 203
Phone
+49
20300
[email protected]
[email protected]
VALLOUREC
VALLOUREC OIL & GAS U
UK
K
Aberdeenshire
United
Kingdom
Aberdeenshire - U
nited Ki
ngdom
Phone
+44
2793400
Phone +
44 1224 27934
V
VALLOUREC
ALLOUREC N
NORGE
ORG E
Stavanger
Norway
Stavanger - No
rway
Phone
+47
Ph
one +
47 51 54 50 1100
VALLOUR
VALLOUREC
EC OIL & GA
GAS
S
Atyrau
Atyrau - Kazakhstan
Kazakhstan
Phone
3219588
Phone +7
+7 7122 32195
[email protected]
[email protected]
VALLOUR
VALLOUREC
EC RUS
RUS
Moscow
Russia
Moscow - Russ
ia
Phone
+77 495 787 49 3300
Phone +
VA
VAM
M® F
Field
ield S
Service
ervice International
International
OFFICES
S
SERVICES OFFICE
VALLOUREC
VALLOUREC OIL & GAS
GAS
Cai
ro - Egypt
Egypt
Cairo
Ph
one +2
+2 022 521 26 89
89
Phone
VALLOUREC
VALLOUREC M
MIDDLE
IDDLE EAST
EAST FFZE
ZE
Du
bai - U
nited Ar
ab Em
irates
Dubai
United
Arab
Emirates
Ph
one +971
+971 4 815 0000
0000
Phone
VALLOUREC
VALLOUREC OIL & GAS N
NIGERIA
IGERIA
LLagos
agos - Nigeria
Nigeria
Ph
one +234
+234 1 463 7456
7456 / 7458
7458
Phone
VALLOUREC
VALLOUREC OIL & GAS C
CHINA
HINA
B
Beijing
eijing - R
Republic
epublic of C
China
hina
Phone
+86
3000
Ph
one +
86 10 5923 30
00
VALLOUR
VALLOUREC
EC ASIA PA
PACIFIC
CIFIC
(Citra Tubindo
Tubindo Pte
Pte Ltd)
Ltd)
(Citra
Singapore
Singapore
Phone +65
+65 6533 895
Phone
89588
[email protected]
[email protected]
VALLOUREC
VALLOUREC USA CCorp.
orp.
Ho
uston, Texa
tates
Houston,
Texass - United S
States
Phone +1
+1 713 4793200
4793200
Phone
[email protected]
[email protected]
FIELD
ELD S
SERVICE
ERVICE IINTERNATIONAL
NTERNATIONAL
VAM
VAM® FI
m
Aberdeenshire, - United Kingdo
Aberdeenshire,
Kingdom
Phone +4
79380
Phone
+444 1224 2279380
[email protected]
[email protected]
VAM
VAM® US
USA
A
Houston,
Texass - United S
States
Ho
uston, Texa
tates
Ph
one +1
+1 281 8215510
8215510
Phone
VA
[email protected]
[email protected]
VAM
VAM® FAR EEAST
AST
Singapore
Singapore
Phone +6
Phone
+655 6736 2233 7722
[email protected]
[email protected]
VALLOUREC
VALLOUREC CANADA
CANADA
Alberta
Canada
Alberta - Ca
nada
Phone
+11 403 23
2330119
Phone +
30119
[email protected]
[email protected]
VAM
VAM® FI
FIELD
ELD S
SERVICE
ERVICE BEIJING
BEIJING
Beijing - R
epublic of C
hina
Beijing
Republic
China
Phone +8
923 300
Phone
+866 10 55923
30088
[email protected]
[email protected]
VALLOUR
VALLOUREC
EC OIL & GAS MEX
MEXICO
ICO
Veracruz
Veracruz - Mexico
Mexico
Phone
+52
87166
Phone +
52 229 9989
89 871
[email protected]
[email protected]
VAM
VAM® FI
FIELD
ELD S
SERVICE
ERVICE ANGOLA
ANGOLA
Luanda - R
epublic of A
Luanda
Republic
Angola
ngola
Ph
one +2
44 222 3399
99 50
Phone
+244
5033
[email protected]
[email protected]
V ALLOUR
ALLOUREC
EC TUBOS D
DO
O BRASI
BRASILL
Rio
Rio de JJaneiro
aneiro - Brazil
Brazil
Phone
Phone +55
+55 21 38738300
38738300
[email protected]
[email protected]
VAM
VAM® CCASPIAN
ASPIAN
B
aku - Az
erbaijan
Baku
Azerbaijan
Ph
one +9
94 124 9927
27 67
Phone
+994
6733
[email protected]
[email protected]
VAM
VAM® S
SERVICES
ERVICES
Au
lnoye Aymeries
Aymeries - Fra
Aulnoye
France
nce
Phone +3
Phone
+333 3 2277 69 6655 8899
For further information on our connections, please visit our website www.vamservices.com
VAM®,
and CLEANWELL® are registered trademarks of Vallourec Oil and Gas France
05/2014- CM5Ouest - 09 81 14 98 50
Get the Vallourec Oil & Gas mobile app.