operator`s manual - Valmar Granular Application Equipment

5500 PT Pneumatic
Granular Applicator
OPERATOR'S
MANUAL
Valmar Airflo Inc.
Issue Date: December 2004
Box 100
Elie, MB R0H 0H0
Phone (204) 353-2782
FAX (204) 353-2864
Email: [email protected]
Box 100
Elie, MB
R0H 0H0
Phone (204) 353-2782
FAX (204) 353-2864
Email: [email protected]
Printed in Canada
Issue Date: December 2004
Part No. 20.11835
VALMAR 5500 PT Applicator
Table of Contents
Item
Page
Serial Number Location
3
1 - Introduction
4
2 - Safety
5
3 - Safety Decals
8
4 - Operation
11
5 - Calibration
19
6 - Adjustments and Service
33
7 - Troubleshooting
42
8 - Options
44
9 - Specifications
46
10- Parts
48
Printing Date: December 2008
Page 1
Page 3
Warranty
VALMAR
VALMAR WARRANTY
All Valmar products are warranted for one year against defects in materials and workmanship and
to perform according to specifications when such products are properly assembled, installed, used
and maintained.
Valmar warrants that its manufactured parts will be as specified and will be free from defects in
material and workmanship.
Valmar's liability under this warranty shall be limited to one of the following:
1. Repair or replacement of the defective part at our discretion.
2. Granting of a reasonable allowance providing action of dealer has been approved by Valmar.
Warranty will be allotted only upon return and inspection of part by Valmar and if part is determined
to be defective in terms of materials or workmanship.
This obligation shall not include any transportation charges or any extra costs or liability for any
direct, indirect or consequential damages or delay.
WARRANTY LIMITED OR VOID
Any use for purposes other than those for which the product was designed, operation beyond rated
capacity, substitution of parts not approved by Valmar, or alteration or repair by others in such
manner as in our judgment affects the product materially and adversely shall void this warranty.
Warranty does not apply to any machine or part which has been repaired or altered in any way so
as in Valmar's judgement to affect its reliabilty, or which has been subject to misuse, negligence, or
accident.
Component parts, equipment, accessories and items not fabricated by Valmar are warranted only
to the extent of the original manufacturer's warranty.
Valmar reserves the right to make improvement changes on any of our products without notice.
WARRANTY CLAIMS PROCEDURE
1. A warranty claim form must be completed by your Valmar dealer.
2. Defective parts for which a warranty claim is made must be returned to Valmar within 15 days
from the claim date.
Page 2
Page 3
VALMAR
Serial Number Location
Serial Number Location
Your Valmar applicator has a model and serial
number to clearly identify it. Always give your
dealer the Model Number and Serial Number of
your machine when ordering parts or requesting
service information. Mark the model and serial
numbers in the spaces provided for easy
reference.
Applicator Serial Number
The Serial Number Plate is located on the front
right-hand inside panel of the hopper as shown
in the photo below.
Model No. ___________________________
Serial No. ___________________________
Page 3
Valmar
Safety
2 – Safety
Read the Operator’s Manual
ALL OPERATORS must read and
understand the Operator’s manual before
working with the applicator. Review the
Operator’s manual and safety decals of this
machine before each season of use.
The Safety Alert Symbol is on all safety
decals. When you see the symbol, follow
the instructions to avoid injury or death.
WARNING
A SPECIFIC HAZARD OR UNSAFE
PRACTICE WHICH COULD RESULT IN
SEVERE PERSONAL INJURY OR DEATH IF
PROPER PRECAUTIONS ARE NOT TAKEN
CAUTION
Signal Words
Note the use of the words DANGER,
WARNING and CAUTION on the safety
decals. Each signal word denotes a
different type of hazard as shown:
UNSAFE PRACTICES WHICH COULD
RESULT IN PERSONAL INJURY IF PROPER
PRECAUTIONS ARE NOT TAKEN, OR AS A
REMINDER OF GOOD SAFETY PRACTICES
Operator Safety
DANGER
AN IMMEDIATE AND SPECIFIC HAZARD
WHICH WILL RESULT IN SEVERE
PERSONAL INJURY OR DEATH IF THE
PROPER PRECAUTIONS ARE NOT TAKEN
Because the 5500PT is a towed applicator,
the operator must observe the safety
requirements of both the towing vehicle and
the applicator. Applicator owners must give
operation instructions to employees or
operators before allowing them to operate
the applicator, and at least annually
thereafter
according
to
OSHA
(Occupational
Safety
and
Health
Administration) Regulation 1928.57.
Page 5
Safety
Follow these safety guidelines:
1. Provide a first aid kit. Store it in a visible,
2.
3.
4.
5.
6.
accessible location and know how to
use it.
Keep safety decals clean and legible at
all times. Replace missing or damaged
decals.
Before servicing, adjusting, repairing or
unplugging the applicator, stop the
tractor, set the park brake and wait for
all moving parts to come to a complete
stop.
Ensure that all guards and shields are in
place. Replace any that are damaged.
Have a qualified tire repairman perform
any tire repairs. Improper tire mounting
procedures can produce a serious
explosion resulting in injury or death.
Do not allow riders on the applicator.
PTO Shaft Safety
Valmar
7. Wash down the applicator prior to any
maintenance. Dispose of wash water in
accordance with local standards and
laws.
8. Know the poison control emergency
telephone numbers in your area.
Hydraulic Safety
1. Keep hydraulic components clean so
that leaks can be easily identified.
2. Replace damaged hoses and fittings.
3. Use a piece of cardboard when trying to
pinpoint leaks. Wear heavy gloves and a
face shield.
4. Have hydraulic components repaired by
a qualified repair facility. Makeshift
repairs may fail suddenly creating a
hazardous condition.
5. If injured by a high pressure stream of
hydraulic fluid, seek medical attention
immediately. Serious infection can
result.
1. Do not operate the PTO unless all
shields and guards are in place.
2. Stop the tractor and wait for all moving
parts to come completely to a stop
before making any adjustments to the
PTO.
3. Be sure that both ends of the PTO shaft
are coupled securely.
Granular Chemical Safety
1. Read
2.
3.
4.
5.
6.
and
strictly
follow
the
manufacturer’s instructions found on the
product container.
Wear chemically resistant clothing,
gloves and safety goggles.
Avoid contact with skin and eyes.
Wear a respirator as directed by the
chemical manufacturer.
Wash thoroughly after working with
chemicals, especially before eating.
Wash all clothing contaminated by
chemicals.
Page 6
Fan Safety
1. Do not operate the fan unless all shields
and guards are in place.
2. Stay well away from the fan during
operation. Keep others away.
3. Stop the tractor and wait for all moving
parts to come completely to a stop
before making any repairs to the fan or
servicing its drive components.
4. Should the fan impellor on the 5500PT
need to be replaced, follow the
instructions set out in the Adjustments
and Service section of this manual.
Failure to install an impellor properly
may crack the impellor potentially
resulting in fan explosion.
Transport Safety
Valmar
Safety
1. Be sure that the SMV (Slow Moving
2.
3.
4.
5.
6.
Vehicle) sign and all reflectors and lights
required by local highway authorities are
in place, clean and functional.
Use a hitch pin that is strong enough to
tow the applicator without breaking.
Use the safety chain to secure the hitch
on the applicator to the tractor.
Do not exceed the maximum speed
rating on implement tires (generally 25
mph or 40 kph).
Ensure that the booms are folded and
latched in place.
Disengage the metering drive tire.
Failure to do so may result in the
metering of chemicals and fertilizer onto
roadways. This may also cause the
metering drive to operate at very high
speeds and damage some of its
components.
Storage Safety
1. Store the applicator on a firm, level
surface.
2. Thoroughly clean the applicator before
storing to avoid contaminating the
surrounding area with pesticide and
fertilizer residue. Dispose of the wash
water in accordance with local standards
and laws.
Page 7
Valmar
Safety Decals
Page 7
Safety Decals
Valmar
3 – Safety Decals
Safety Decals
Keep safety decals clean and legible at all times. Replace decals that are missing or have become
illegible. Safety decals are available from the Valmar Parts Department.
Safety Decal Installation
•
•
•
•
•
•
Be sure the installation area is clean and dry.
Decide on the exact position before removing the backing paper.
Remove the smallest portion of the backing paper.
Align the decal over the desired area and press the small portion of the decal into place.
Remove the remainder of the backing paper and press the entire decal in place.
Pierce any air pockets and smooth them out.
Familiarize yourself with the location and message of all safety decals on these pages.
Page 8
VALMAR
Safety
Decal 1
Decal 4
Decal 2
Decal 5
Decal 3
Decal 6
Page 9
Safety Decals
Page 10
Valmar
Valmar
Operation
4 – Operation
Your 5500PT applicator is designed to efficiently broadcast fertilizer, granular pesticides and seed.
As noted in the diagram below, the 5500PT uses a PTO driven fan to blow product through an air
delivery system. Grooved metering rollers accurately meter product from the hopper into the
venturis. Air passing through the manifold and venturis draws the product into an airstream and
delivers it to the boom where it is spread onto the field by the deflectors. Product application rate is
governed by either a sixty speed metering gearbox which is driven by a hydraulically engaged ground
drive wheel or by a hydraulically driven rate controller.
Figure 4-1
Page 11
Operation
Pre-Operation Checklist
Before operating the applicator, inspect the
following areas. If adjustments are necessary,
see the Adjustments and Service chapter of
this manual for specifications.
Valmar
The minimum hydraulic flow requirement is 23
U.S. gallons per minute. The hydraulic fan drive
motor is equipped with a case drain which must
be plumbed to the tractor hydraulic system for
proper operation. See Figure 4-2 for correct
hookup of the pressure and return lines.
1. Ensure that the applicator is securely
hitched to a tractor with a minimum of 80
PTO horsepower with a 1000 RPM PTO
shaft. Use a drawpin with a retainer that is
rated for towing the load.
2. Attach the safety chains to the tractor.
3. Ensure that the PTO shaft is securely
connected to the tractor and to the
applicator fan drive.
4. Inspect the hopper and metering system for
debris. Clean if necessary.
5. Make sure that all guards and shields are in
place.
6. Ensure that all tires are at the correct
pressure as noted in the Adjustments and
Service chapter.
7. Ensure that all hydraulic lines are connected
securely to the tractor remotes.
A check valve is installed on the hydraulic fan
drive to allow the fan impellor to freewheel to a
stop when oil flow is cut off. The fan must not
be operated without a check valve in place.
Operation
Air Restrictor
PTO Fan Engagement
An air restrictor must be used whenever
metering product with the 28 groove red roller
with the 5500PT. Bolt the restrictor over the fan
inlet as shown in Figure 4-3. Continue to run
the fan at 1000 RPM.
With the tractor engine at low idle, engage the
PTO clutch gradually to prevent fan belt
slippage. Slowly increase engine speed until
proper PTO speed of 1000 RPM is achieved.
The fan must be run at this speed at all times
for proper material delivery. Do not exceed this
speed or fan damage may occur.
Hydraulic Fan Engagement
The speed of the hydraulically driven fan is set
by adjusting the tractor hydraulic flow controller
until the pressure gauge at the front of the hitch
registers 30 inches of water column pressure.
The fan must be run at this speed at all times
for proper material delivery. Do not exceed this
speed or fan damage may occur.
Page 12
Figure 4-2
Valmar
Operation
5. Fold the boom tips into position until they
lock in place.
6. Reverse the above procedure to fold the
booms.
Lock
Pin
Figure 4- 3: Air Restrictor
Boom Unfolding
Unfold the booms as follows:
1. Unlatch each boom by lifting up on the
boom transport lock handle on each side of
the hopper as shown in Figure 4-4.
2. Remove the lockpin shown in Figure 4-5
from the boom lock lever.
Figure 4-4
3. Swing the booms into the field position by
hand or hydraulically if the hydraulic boom
fold is installed.
4. Lock the boom into the field position by
forcing the boom lock lever into the
overcentre position as shown in Figure 4-5.
Secure it in this position with the lock pin.
Figure 4-5
Wheel Tread Adjustment (Walking Beam)
If equipped with walking beam axles, the wheel
tread spacing on the 5500PT is infinitely
adjustable in a range between 81” and 99” with
the 16.5 X 16.1 tires, and between 72” and 90”
with the 9.00 X 20 tires. Adjust the wheel tread
as follows:
1. Jack up the one side of the rear of the
applicator frame until the walking beam tires
are off the ground.
2. Loosen the clamping bolts indicated in
Figure 4-6 until the axle beam is able to
move freely.
3. Place the point of a pry bar in a suitable
hole in the adjustment plate and pry the axle
one way or the other until the tires are at the
correct spacing.
4. Tighten the clamping bolts securely.
5. Repeat for the other walking beam of the
applicator.
Page 13
Operation
Valmar
Slide the gear set out of engagement with the
metering roller gears. Reinstall the cotter pin to
lock the gear set in the disengaged position.
Figure 4-6
If your 5500 PT is equipped with a single axle
option, the wheel spacing is factory set and
should not be adjusted or the wheel drive
engagement system will not line up with the tire
properly.
Wheel Drive Engagement
In order to engage the wheel drive, activate the
correct hydraulic remote and keep it engaged
until the remote kicks out. Now the metering
rollers will turn when the applicator is in motion.
Reverse this procedure to disengage the wheel
drive.
Ensure the wheel drive is disengaged
before transporting the applicator.
Failure to do so may result in severe
damage to the ground drive tire or other
metering components.
Half-Width Application
If the operator wishes to make a ½ width
application, each metering roller can be
disengaged by removing a cotter pin from the
gear set on the bottom shaft (See Figure 4-7).
Page 14
Figure 4-7
Setting the Mechanical Metering Gearbox
Up to 60 product application rates are available
with the mechanical metering gearbox. Three
mechanisms need to be set to select the
desired application rate: the input ratio, the
range and the speed.
Input Ratio
Four input ratios can be selected by pairing the
12 tooth gear with the 34 tooth gear or the 19
tooth gear with the 27 tooth gear on the side of
the gearbox. The available ratios are Ultra Low,
Low, Medium and High as shown in the
following diagrams. Select the desired input
ratio as follows:
1. Raise the gearbox shield.
2. Select the pair of gears corresponding to
the desired input ratio and install them, in
the correct orientation, on the shafts
indicated in the diagrams using linch pins.
3. If the appropriate gears are not on the
shafts, they can be found on the storage
shaft on the opposite side of the gearbox.
4. Store the two unused gears on the storage
shaft.
Valmar
Figure 4-8: Ultra Low
Operation
Figure 4-10: Medium
Figure 4-11: High
Figure 4-9: Low
Range Selection
1. Release the clip on the gearbox shifter and
lift up.
2. Move the range lever to the “A” or “B”
position.
3. Check for proper alignment of the top and
bottom gear clusters. Lock the speed shifter
into place by pushing down on the clip.
Page 15
Operation
Valmar
Each revolution of the pesticide metering rollers
applies 22.46 cubic inches of material (.013
cubic feet).
For every revolution of the hydraulic motor, the
fertilizer metering rollers will turn .107 turns.
For every revolution of the hydraulic motor, the
pesticide metering rollers will turn .043 turns.
For every revolution of the hydraulic motor, the
fertilizer metering rollers will expel 15.78 cubic
inches of material (.009 cubic feet).
Figure 4-12: Range & Speed Selection
Speed Selection
1. Release the clip on the gearbox shifter and
lift up.
2. Move the speed shifter sideways to the
correct numbered detent position. Drop the
speed shifter into the detent slot.
3. Check for proper alignment of the top and
bottom gear clusters. Lock the speed shifter
into place by pushing down on the clip.
Hydraulic Metering Drives
The 5500PT can be equipped with a hydraulic
metering drive system, whereby application
rates are set by regulating the oil flow to a
hydraulic motor which drives the metering
system. Valmar offers either a Char-Lynn or a
Rawson hydraulic metering drive system.
Certain parameters of the 5500PT metering
system need to be entered into the metering
rate controller for accurate application:
Each revolution of the fertilizer metering rollers
applies 157.8 cubic inches of material (.091
cubic feet).
Page 16
For every revolution of the hydraulic motor, the
pesticide metering rollers will expel .97 cubic
inches of material (.0005 cubic feet).
Char-Lynn Metering Drive
The Char-Lynn motor has a displacement of 2.8
cubic inches per revolution. The end user
must purchase all other components of the
metering rate control system separately.
Rawson Metering Drive
The Rawson hydraulic motor has a
displacement of 3 cubic inches per
revolution. Detailed instructions for setting your
Rawson rate controller are included in the
5500PT Rawson kit and in the Rawson Rate
Controller Instructions.
Maximum Speeds
The 5500PT should never be towed faster than
20 mph when loaded.
Disc Marker
The disc marker can be placed in transport or
field position as shown in Figure 4-13.
Valmar
Operation
Figure 4-13: Disc Marker Operation
Page 17
Operation
Page 18
Valmar
Valmar
Calibration
5 – Calibration
Calibration determines the actual product flow
rate of your applicator. Generally the metering
rate of fertilizer, granular product and seed is
predictable as long as its properties are
consistent. However, metering rate variations
are possible and may be caused by:
•
•
•
•
Manufacturer’s quality control
Damaged or worn metering components
A change in product density due to
settling during transport
Variations in seed size and density due
to changes in growing conditions
For these reasons, product flow rate charts are
intended as a guide only. Calibration is
essential for accurate application. The
applicator should be calibrated the first time a
new fertilizer or granular product is used and
periodically thereafter. For seed, the applicator
should be calibrated each time a particular
batch of seed is applied. When applying seed
mixtures, consult the New Product Calibration
instructions on page 30 to determine
appropriate gearbox settings.
Use the following procedures to ensure your
applicator is metering product as precisely as
possible. Refer to the Operation Chapter of this
manual for specific instructions on setting the
metering components.
Calibration Set-up
1. Pour sufficient product into both metering
bottoms for the calibration.
2. Remove the venturi bottom plates by
unhooking the rubber latch from each plate
as indicated in Figure 5-1.
Figure 5-1
3. Insert a venturi inlet cover into each venturi
as shown in Figure 5-2. This cover prevents
product from falling into the manifold during
calibration.
Page 19
Calibration
Figure 5-2
4. Place a container underneath each venturi
to catch the product to be calibrated.
5. Remove the calibration crank from its
storage position shown in Figure 5-3.
Valmar
Figure 5-4
7. Set the metering gearbox for the desired
application rate.
8. Ensure that the ground drive tire is
disengaged from the trailer tire. Rotate the
ground drive tire in a counter-clockwise
rotation as shown in Figure 5-4 until product
begins to flow into the calibration container.
9. Empty the calibration containers back into
the hopper. Place the empty containers
underneath the venturis.
Calibration
Figure 5-3
6. Install the calibration crank on the ground
drive tire as shown in Figure 5-4.
1. Turn the calibration crank 54 times for a 40
foot boom and 60 times for a 36 foot boom.
2. Weigh the calibration container. Subtract
the weight of the empty container. Multiply
the product weight by 5 to arrive at the
application rate in pounds per acre.
The crank turns are based on the number of tire
revolutions in 1/5 of an acre (271 ÷ 5 = 54.2 for
a 40’ Boom). The product weight is then
multiplied by 5 to yield the result for application
on one acre.
If your 5500PT is equipped with a hydraulic
metering
drive,
follow
the
calibration
instructions provided by the manufacturer of
your rate controller.
Page 20
Valmar
Calibration
Calibration Results
•
For the mechanical metering drive, compare
your calibration results with the Product Flow
Rate Charts on the following pages. For
hydraulic metering drive, compare your
calibration results with the target rate set on the
controller. A difference in flow rates could
indicate the following:
•
•
•
•
•
The metering drive gearbox is not
properly set.
The flow rate characteristics or density
of the product has changed.
Metering rollers are worn or damaged.
A mathematical error was made during
calibration.
Data was incorrectly entered into the
rate controller.
A sprocket in the metering drive system
has been changed in the past. See
Figure 5-5 for the correct sprocket
layout.
If a difference still exists after eliminating the
above possible causes, contact your Valmar
dealer.
Charts for the 5500PT can also be found on
Valmar’s website:
www.valmar.com
Figure 5-5
Page 21
Calibration
Page 22
Valmar
Valmar
Calibration
Page 23
Calibration
Page 24
Valmar
Valmar
Calibration
Page 25
Calibration
Page 26
Valmar
Valmar
Calibration
Page 27
Calibration
Page 28
Valmar
Valmar
Calibration
Page 29
Calibration
Valmar
New Product Calibration
When applying product that is either not listed on the Product Flow Rate Charts (such as grass
mixtures) or that is inconsistent with the charted values, it is necessary to create a flow rate chart. Use
the following procedure to prepare flow rates for all possible gearbox settings.
Calibration Set-up
Follow the same procedure as given at the beginning of this chapter.
Calibration
1. Set the gearbox to Low Ratio, Range B, Speed No. 8. At this setting the gearbox input to output
ratio is 1 to 1.
2. Turn the crank 54 times for a 40’ boom, and 60 times for a 36’ boom.
3. Weigh the calibration containers. Subtract the weight of the empty containers. Multiply the result by
5 to arrive at the calibration weight.
4. Record this weight on the blank Product Flow Rate Chart in the Calibration Weight column.
5. Multiply this calibration weight by the Gearbox Adjustment Factors listed on the chart in order to
calculate the actual application rate in pounds per acre for all the other gearbox settings.
Example Calculation (Table 5-1)
A grass mixture is to be applied at 1.8 pounds per acre. A calibration was performed in which 1.2
pounds of product was collected. This was multiplied by 5 as instructed in Step 3 to arrive at a
calibration weight of 6 pounds.
Therefore, the application rate was 6 lbs/acre in Low Ratio, Range B, Speed No. 8. This weight was
recorded in the Calibration Weight column of the blank charts. This weight was then multiplied by each
Gearbox Adjustment Factor in the chart to calculate what the flow rate would be at all the other gearbox
settings. It was found that Ultra Low Ratio, Range B, Speed No. 3 was the correct setting for 1.8
pounds per acre of the grass mix.
The gearbox was set to Ultra Low Ratio, Range B, Speed No. 3 and an applicator calibration performed
as a final check.
Product
Gearbox
Adjustment
Factor
Cal.
Product
Weight
No. 1
No. 2
A
B A
B
.25 .26 .28
Product Flow Rate Chart in lbs / Acre
Metering Gearbox Setting
No. 3
No. 4
No. 5
No. 6
A
B
A
B
A
B
A
B
.29 .30 .32 .34 .35 .37 .39 .41
XYZ
6
1.5 1.6 1.7 1.7 1.8*
Table 5:1: Flow Rate Example Calculation
1.9
2.0
2.1
2.2 2.3
2.5
No. 7
No. 8
A
B
A
B
.43 .45 .47 .50
2.6
2.7 2.8
Input
Ratio
Ultra
Low
Ratio
3.0
*Calculated from .30 X 6 = 1.8 lbs/acre
Page 30
Valmar
Calibration
Page 31
Calibration
Page 32
Valmar
Troubleshooting
Valmar
7 – Troubleshooting
Should you encounter problems with your applicator, this chapter lists possible causes and solutions. If
the problem persists even after taking the steps recommended here, call your Valmar dealer. Before
you call, have this operator’s manual and the applicator serial number ready.
Problem
Cause
The rate of product being Product density has changed
applied is lower that expected.
resulting in a discrepancy with
the charts.
Solution
Recheck
product
density.
Calibrate your applicator. Create
a new chart. If using a hydraulic
metering drive, check rate
controller
for
correct
programming.
Mathematical error made during Recheck calculations.
calibration.
Mistake made while weighing Weigh sample again.
calibration sample.
Actual acreage covered less Recheck field size.
than expected.
Tractor wheel slippage may be
causing an incorrect odometer
reading.
Ground drive wheel is slipping.
Replace damaged bearings.
Damaged bearings are causing
the metering system to drag.
Metering rollers caking up with Clean rollers.
product.
Metering rollers are worn out.
Replace rollers.
The rate of product being Ground drive tire pressure is too Inflate ground drive tire to 30 psi.
applied is higher than expected. low.
Product density has increased Recheck product density and
while machine is moving.
calibrate the applicator. Create a
new chart. If using a hydraulic
metering drive, check the rate
controller
for
proper
programming.
Page 42
Valmar
Trouble Shooting
Problem
Cause
Solution
Product shooting out of the Obstruction in the venturis, Remove the obstruction.
venturis; venturis filling up and delivery hose or booms.
spilling over.
Fan speed too low.
Increase tractor engine speed to
proper PTO speed. Increase
tractor hydraulic flow to achieve
30 inches of water column
pressure. Check fan belt for
slippage.
Hose from fan to manifold torn.
Replace hose.
Water in hopper and/or fan Clean out and wash the hopper
causing product to stick to and manifold. Run the fan to
venturis, delivery hose or blow-dry the delivery system.
booms.
Fan inlet restrictor not in place. Install the fan inlet restrictor
Product flow rate insufficient to when applying herbicides and
properly induct into air stream in seeds, or when applying very
venturis.
low rates of fertilizer.
Application rate is exceeding the Choose slower ground speed.
capacity of the venturis at that
particular ground speed.
Metering system will not operate. Wheel drive is not engaged.
Engage wheel drive. Check
hydraulic coupler for proper
connection.
Metering gearbox shearpin is Check
metering
drive
broken.
components for obstructions or
damage. Replace shear pin after
repairing damage.
Hydraulic metering drive motor Check hydraulic couplers for
will not turn.
proper connection. Check rate
controller
for
proper
programming.
Hydraulically activated booms Boom latch is engaged.
Disengage boom latch.
will not unfold.
Hydraulic coupler not connected. Connect hydraulic coupler.
Page 43
Options
Valmar
8 – Options
Various options are available for the 5500 PT to
widen the range of uses for the applicator and
to enhance its performance. This section offers
a brief description of each of the options as well
as potential reasons for using them. Detailed
instructions for the assembly and operation of
the optional equipment are contained in the kits
themselves. See your Valmar dealer for pricing
and availability.
end of each boom to avoid overlaps and
misses.
Boom Extension Kit (02.4469)
This kit will extend a 36 foot boom to 38 feet.
Hopper Screens (18.12029)
Herbicide Metering Kit (18.3699)
A set of screens is available to minimize the
possibility of unwanted material falling into the
hopper.
The herbicide metering kit includes a set of 28
groove metering rollers for applying herbicides
and small seeds as well as a fan inlet restrictor.
Acre Counter
Foam Marker Kit
A hub-mounted acre counter is available for
operators who wish to have an accurate
measure of the area they apply product to.
A foam marker kit is available for the 5500 PT
that drops an easy to see foam strip from the
end of each boom to avoid overlaps and
misses.
40’ Boom – 18.12127
Two sizes of foam markers are available: the 22
gallon model (18.10852) and the 33 gallon
model (18.10853). Both kits require a mounting
kit (18.5985) in order to install the equipment
properly.
Disc Marker (18.12094)
A mechanical disc marker is available that
leaves an easy to see gouge in the soil at the
Page 44
36’ Boom – 18.12128
Electronic Acre Counter (18.9692)
An electronic cab-mounted acre counter is also
available which will monitor application rate as
well.
Valmar
Options
Shaft & Bin Monitor (18.9688)
Rawson (18.13137)
An electronic shaft and bin level monitor is
available which will warn operators of a
metering system stoppage and low bin level.
The bin level sensor is also available in a kit by
itself (18.9691)
This kit comes with mounting brackets, hoses,
filter, sprockets and chain for a Rawson
hydraulic metering drive system.
Optional PTO shaft (11.7680)
A 1 ¾” – 20 spline PTO shaft coupler is
available for operators whose tractors require it.
The 3.0 CID Rawson hydraulic motor kit
(18.13135) must be purchased separately. This
kit comes with a Rawson rate controller, driver
box and wiring harness.
A Rawson Speed Sensor Kit (18.13136) is also
available for monitoring tractor speed.
Tires
Three types of tires are available for the
5500PT:
Walking Beam:
Flotation Tire: 16.5L – 16.1
Row Crop Tire: 9.00 X 20
Single Axle:
Alliance Flotation 328
Hydraulic Fan Drive
A Hydraulic fan drive kit (18.13095) is available
for the 5500PT. It is driven by a 28cc Rexroth
motor. This option requires a hydraulic flow rate
of 23 U.S. gpm.
Hydraulic Metering Drive
Two kits are available for hydraulically driven
metering:
Char-Lynn (18.13211)
This kit comes with a Char-Lynn 2.8 CID
hydraulic motor, mount bracket and drive
sprockets and chain. End user must purchase a
rate controller kit and hydraulic hoses
separately.
Page 45
Specifications
Valmar
9 – Specifications
Hopper
Stainless steel welded
Capacity
167 Cubic Feet (132 bushels) (7515 lbs @ 45 lbs/cubic foot)
Weight (empty)
4480 pounds
Fan
20 inch aluminum impellor
Maximum speed: 4800 rpm
Impellor Hub bolt torque: 20 ft. lbs.
Fan Drive
1000 RPM PTO Option
1 3/8 – 21 Spline standard
1 ¾ - 20 Spline optional
Constant velocity joint maximum temporary operating angle: 80°
Minimum recommended horsepower: 80
Hydraulic Fan Drive Option
32cc Rexroth motor standard; 28cc optional
32cc motor requires 23 U.S. GPM oil flow;
28cc motor requires 21.5 U.S. GPM oil flow
Case drain required
Fan Belt:
PTO drive: 3VX850 – 4 Band
Hydraulic Fan Drive: 3VX500 – 4 Band
Tires
Standard: 16.5L – 16.1 Flotation
Optional: 9.00 X 20 Row Crop
Single Axle: Alliance Flotation 328
Ground Drive Tire: 4.00 X 8 (1314 revolutions per mile)
Trailer Tire wheel bolt torque: 120 ft. lbs.
Page 46
Valmar
Specifications
Tread Spacing
16.5L – 16.1 Tires: 81” to 99”
9.00 X 20 Tires: 72” to 90”
Single Axle: not adjustable
Operating Width
40 Feet
36 Feet extendable to 38 Feet
Hydraulics
One remote required for ground drive engagement
One remote and case drain required for hydraulic fan drive
One remote required if hydraulic boom fold is installed
Metering System
Fertilizer: 12 Groove Stainless Steel Rollers
Pesticide: 28 Groove Red Roller
60 Speed Gearbox
Rawson or Char-Lynn hydraulic metering drive optional
Metering Gearbox Ratios (Input to Output)
No. 1
A B
No. 2
A
B
No. 3
A
B
No. 4
A
B
No. 5
A
B
No. 6
A
B
No. 7
A
B
No. 8
A
B
.250
.265
.276
.292
.305
.321
.336
.353
.371
.388
.409
.427
.451
.471
.498
Input
Gear
U. Low
.498
.528
.551
.581
.608
.640
.670
.704
.739
.774
.815
.852
.899
.938
.993
Low
1.007
1.066
1.112
1.174
1.227
1.292
1.353
1.421
1.492
1.563
1.645
1.720
1.816
1.895
2.006
Med.
2.007
2.125
2.217
2.341
2.447
2.576
2.698
2.833
2.975
3.117
3.281
3.430
3.620
3.778
4.000
High
Figure 9-1: Dimensions
Page 47
Parts
10 – Parts
Page 48
Valmar
Valmar
Parts
PTO SHAFT - #6 Driveline (2005 Models & Older)
ITEM
PART NO.
DESCRIPTION
QTY
4
5
6
7
8
9
10
11
12
13
14
11.7550
11.7640
11.7641
11.7680
11.7642
11.11774
11.11776
11.6262
11.11775
11.7669
11.6265
11.7646
11.7647
11.7648
11.7649
11.7650
11.7651
11.7652
PTO Driveline Complete 1 3/8 - 21 Spline
PTO Driveline Complete 1 3/4 - 20 Spline
Yoke with Bridge 1 3/8 - 21 Spline
Yoke with Bridge 1 3/4 - 20 Spline
Cross Journal Assembly
Quick Disconnect - 1 3/8 - 21 Spline
Quick Disconnect - 1 3/4 - 20 Spline
Grease Nipple
Ratchet with Springs
Shield Assembly
Grease Nipple
Flexible Pin
Outer Tube
Inner Tube
Flexible Pin
Inner Yoke
Cross Journal Assembly
Torque Limiter Assembly
1
1
1
1
2
1
1
3
3
1
1
1
1
1
1
1
1
1
15
16
17
18
19
20
21
11.7654
11.7551
11.7656
11.7657
11.7659
11.7660
11.7661
Outer Bearing
Shear Bolt - 5 Pack
Outer Safety Tube
Inner Safety Tube
Inner Bearing
Ring Nut Dowels
Complete Shell
1
1
2
3
1
1
1
1
1
Page 49
Parts
Page 50
Valmar
Valmar
Parts
PTO SHAFT - SFT Driveline (2006 Models & newer)
ITEM
PART NO.
DESCRIPTION
QTY
4
5
6
7
8
9
10
11
12
13
14
11.12243
11.12244
11.12315
11.12329
11.12316
11.11774
11.12330
11.12327
11.11775
11.12318
11.6265
11.12319
11.12320
11.12321
11.7649
11.12322
11.12323
11.12324
PTO Driveline Complete 1 3/8 - 21 Spline
PTO Driveline Complete 1 3/4 - 20 Spline
Yoke with Bridge 1 3/8 - 21 Spline
Yoke with Bridge 1 3/4 - 20 Spline
Cross Journal Assembly
Quick Disconnect - 1 3/8 - 21 Spline
Quick Disconnect - 1 3/4 - 20 Spline
Outer Safety Shield Assembly
Ratchet with Springs
Shield Assembly
Grease Nipple
Flexible Pin
Outer Tube
Inner Tube
Flexible Pin
Inner Yoke
Cross Journal Assembly
Torque Limiter Assembly
1
1
1
1
2
1
1
1
3
1
1
1
1
1
1
1
1
1
15
16
17
18
19
20
11.12328
11.12326
11.7551
11.12325
11.12402
11.12575
Inner Safety Shield Assembly
Inner Safety Tube
Shear Bolt - 5 Pack
Outer Safety Tube
Central Body
Outer Yoke
1
1
1
2
3
1
1
1
Page 51
Parts
Page 52
Valmar
Valmar
Parts
FAN DRIVE – PTO
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
03.7351
14.7336
03.7347
03.11876
03.13236
09.1086
12.7370
11.7553
17.7348
11.7334
11.7554
03.11881
04.11880
03.11882
08.7363
11.7555
Front Mount - Driveline
Bearing - Square Flange
Fan Drive Shaft
Fan Post (Pre- 2008 models)
Fan Post (2008 models and newer)
Idler Spring
Idler Spring Sleeve
Sheave 3V-4-19.0 SF
Key 5/16 x 5/16 x 2
Split Tapered Bushing SF 1 3/8
Belt 3VX850 - 4 Band
Belt Shield - RH
Belt Shield - Rear
Belt Shield - LH
Idler Pivot
Idler Pulley - 5" dia. X 2" wide
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
16
17
18
19
20
21
22
17.6181
07.4899
03.7362
04.7352
03.12025
05.13238
03.13247
Grease Zerk - 1/4 90 degree
Idler Pulley Spacer
Idler Arm
Shaft Shield
Arm – Hydraulic Hose Support
Plate – Pulley Mount (2008 & newer)
Bracket – Shield (2008 & newer)
1
1
1
1
1
1
1
Page 53
Parts
Page 54
Valmar
Valmar
Parts
FAN DRIVE – HYDRAULIC
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
03.13236
03.13237
17.297
03.13106
11.13109
11.13110
11.13108
03.13066
17.299
17.13111
03.13072
12.12652
04.13071
12.12964
13.10588
Fan Post
Mount – Hydraulic Fan Motor
Bracket – Rubber Latch
Mount Plate Assembly
Sheave – 3V-4-650 SK
Bushing – Split Taper SK 30mm
Belt – 3VX 500-4 Strand
Shield
Rubber Latch - long
Bolt – ½ X 4 NC Full Thread
Arm – Hose & Gauge Mount
Gauge – Pressure
Mount – Gauge
Filter – Pressure Gauge
Connector – ¼ Tube X 1/8 NPT
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
16
17
18
19
20
21
22
23
24
25
26
27
28
12.12835
12.4017
13.13115
13.10396
13.13114
13.13073
13.13113
13.13074
13.13124
13.8218
13.13116
13.9299
13.4464
Hose – Poly ¼ X 114”
Connector
Pioneer Male Coupler – ¾ NPT
Check Valve – 65psi ¾ NPT
Hydraulic Hose – ¾ x 88”
Tee – ¾ NPT X 12 JIC
Hydraulic Hose – ¾ X 40”
Fitting – 16 ORB X 12 JIC
Hydraulic Motor – Rexroth 28 cc
Elbow – 08 ORB X 06 JIC
Hydraulic Hose – 3/8 X 136” (Case Drain)
Reducer Bushing – ½ X 3/8 NPT
Pioneer Male Coupler – ½ NPT
1
1
2
1
2
2
2
2
1
1
1
1
1
Page 55
Parts
Page 56
Valmar
Valmar
Parts
FAN
ITEM
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
02.7368
02.3451
04.8834
11.3718
11.7552
03.8677
17. 262
11.3716
19.3448
17.1513
14.4089
08.3452
19.3453
02.8645
DESCRIPTION
Fan, Complete
Hub Assembly
Air Restrictor Plate
Split Tapered Bushing SH 1 1/4
Sheave 3V - 4 - 4.12 SH
Cover - Fan Inlet
Key, 1/4 x 1/4 x 1.75
Split Tapered Bushing, SK 1 1/4
Impellor
Retaining Ring N5000 - 281
Bearing, 6207 - 2RS - C3 HT51
Fan Shaft
Hub
Fan Housing
QTY
1
1
1
1
1
1
2
1
1
2
2
1
1
1
Note
If it is necessary to disassemble the fan for any reason, consult page 38 of this
manual for detailed assembly instructions.
An improperly mounted fan impellor can explode and hurl fragments at very high
speeds.
Page 57
Parts
Page 58
Valmar
Valmar
Parts
MANIFOLD
ITEM
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
23.10691
12.7365
03.4115
03.4114
02.11844
02.5954
02.5953
23.10682
23.10910
03.3410
17.1802
12.4843
12.4844
12.4845
12.4846
12.4847
12.4848
03.4125
03.4124
23.4415
03.3604
13
14
15
16
DESCRIPTION
Hose Clamp HAS 80
Hose, 5" x 58"
Manifold, RH
Manifold, LH
Lanyard
Venturi, RH
Venturi, LH
Latch
Spacer Tube
Bottom Cover
Rubber Latch
Hose, 2 1/2" x 73"
Hose, 2 1/2" x 74"
Hose, 2 1/2" x 80"
Hose, 2 1/2" x 85"
Hose, 2 1/2" x 91"
Hose, 2 1/2" x 96"
Venturi Housing, RH
Venturi Housing, LH
Hose Clamp, HAS 44
Inlet Cover
QTY
4
2
1
1
2
1
1
4
4
2
2
2
2
2
2
2
2
1
1
12
2
Page 59
Parts
Page 60
Valmar
Valmar
Parts
BOTTOM ASSEMBLY
ITEM
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
07. 703
17. 388
03. 11857
03.11847
14. 110
14.4625
23.11854
03.3418
03.3421
09. 964
23.12024
23.4612
03.12012
17.12008
14.4540
03.12005
03.11858
03.3477
08.12009
05.12010
DESCRIPTION
Connecting Sleeve
Clip, Hitch Pin
Gear Ass’y – 16 / 30T
Bottom
Shaft Seal
Bearing, 1"
Bottom Shaft
Roller Latch Mount
Roller Latch
Spring, SS
Roller Chain # 40NI - 68 Rollers
Connecting Link # 40NI
Jackshaft Mount
Snap Ring N5000-156
Bearing – 6203 2RS C3 17 mm bore
Sprocket Ass’y – 32 / 13T
Sprocket – 40X54 1” bore
Slide – Shutoff
Spacer
Spacer
QTY
1
2
1
2
4
4
2
2
2
2
1
1
1
1
2
1
1
2
1
1
Page 61
Parts
Page 62
Valmar
Valmar
Parts
ROLLER ASSEMBLIES
ITEM
PART NO.
DESCRIPTION
QTY
Items 1 thru 12 are components of the Herbicide Roller Kit (18.11817)
1
2
3
4
5
6
7
8
9
10
11
12
03.4090
02.3601
14. 239
03.3688
03.3689
08.6535
17.5731
03.3690
15.7388
15.7389
03.6118
03.3394
Top Plate
Clear Shield
Bearing 1"
Roller End Plate RH
Roller End Plate LH
Shaft - Roller
Snap Ring 5108-106
Calibration Bar
Roller Segment - 1.5"
Disc - Roller End
Gear – 56T
Handle
2
2
4
2
2
2
4
2
24
4
2
2
Items 12 thru 22 are components of the Fertilizer Roller Assembly (02.11861)
13
14
15
16
17
18
19
20
21
22
03.11860
11.3422
11.1566
14. 239
03.3389
03.3390
03.4066
11.1408
03.7560
03.3392
Gear 42T
Gear 32T
Gear 16T
Bearing 1"
Roller End Plate RH
Roller End Plate LH
12 Groove Roller S.S.
Bearing, 3/4 Hex
Roller Wiper
Calibration Bar
2
2
2
4
2
2
2
4
2
2
Page 63
Parts
Page 64
Valmar
Valmar
Parts
METERING GEARBOX
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
PART NO.
DESCRIPTION
QTY
02.12020
1
03.12129
03.12863
11.9636
11.9635
11.9629
11.9626
23.12016
23.12859
23.12017
23.12018
17.9640
17.3127
11.1408
23.11279
03.9641
03.5587
23.12019
Gearbox Assembly (inc. items 1 thru 24,
30 & 31 & gear clusters)
Gearbox Case (for hex bore bearings only)
Gearbox Case (for use with items 30 & 31)
Gear - 34T
Gear - 27T
Gear - 19T
Gear - 12T
Shaft – Input (for hex bore bearings only)
Shaft – Input (for use with items 30 & 31)
Shaft - Centre
Shaft - Output
Linch Pin, 3/16 x 1 ¼
Washer – Gear Spacer
Hex Bore Bearing, 1 ¾
Spring Pin, 3/16 x 1 SS
Shifter
Carriage Channel
Shaft - Top Shifter
1
1
1
1
1
1
1
1
2
1
3
4
4
6
1
1
1
17.6164
04.9642
11.1397
23.6008
02.9646
11.1401
09.6124
11.9632
23.6329
23.12023
03.12106
03.12107
23.12108
14.4612
18.12109
14.12858
14.12864
Locking Nut, 3/8 NC
Track, Idler
Tube, Spacer
Flange HHCS ¼ x3/4 NC SS
Idler Gear Assembly - 20T
Spring
Spring Clip
Gear – 22T
Plate – Adjustment
Chain - Roller #40 NI - 172 Rollers
Sprocket - 40B20 ¾” bore (40’ boom)
Sprocket – 40B18 ¾” bore (36’ boom)
Spring Pin – 1/8 X 1 SS
Connecting Link - #40 NI
Shear Pin Kit
Bearing – 1”
Flangette Bearing
2
2
1
3
1
1
1
2
1
1
1
1
1
1
1
2
2
Page 65
Parts
Page 66
Valmar
Valmar
Parts
GEARBOX CLUSTERS
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
11.1400
11.9634
11.9633
11.9632
11.9631
11.9630
11.9629
11.9628
17.3127
11.9627
17.6416
07.5579
Bushing - Plastic
Gear - 24T
Gear - 23T
Gear - 22T
Gear - 21T
Gear - 20T
Gear - 19T
Gear - 18T
Spacer
Gear - 17T
Shim - .075 thick
Shaft Collar - Long
2
2
2
2
2
2
2
2
3
2
2
1
Page 67
Parts
Page 68
Valmar
Valmar
Parts
MECHANICAL WHEEL DRIVE – WALKING BEAM
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
03.11884
03.12866
03.12288
03.12287
03.11977
03.11980
03.11981
03.11985
03.12286
09.12289
10.1204
13.11447
14.239
23.11951
03.12292
02.11997
02.11998
Axle – Wheel Drive
Axle –Wheel Drive (for triangular tube driveline)
Arm – Wheel Drive
Link – Upper
Lower Link
Pin - Long
Pin - Short
Receiver - Crank
Base – Wheel Drive
Spring - Compression
Tire & Rim 400 / 8 - 4 Ply
Hydraulic Cylinder – 1.5 X 6
Ball Bearing – 1” ID
Pin – Cylinder
Swivel
Driveline – Telescopic Male Half (square shaft)
Driveline – Telescopic Female Half (square shaft)
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
17
18
19
20
21
22
23
24
25
13.12027
13.1351
13.4464
13.8552
08.12291
15.9175
23.12290
17.12549
11.12868
Fitting – 06 ORB X 04 JIC Elbow
Fitting – ½ NPT X ¼ Reducer
Fitting – Pioneer Male Coupler 8010-4
Hydraulic Hose – ¼” X 264”
Disc – Spacer
Spacer – Rubber
Lockout Pin
Hex Nut – 5/8 NF
Driveline - Telescopic (triangular tube shaft)
2
2
2
2
1
1
1
2
1
Page 69
Parts
Page 70
Valmar
Valmar
Parts
MECHANICAL WHEEL DRIVE – SINGLE AXLE
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
03.11985
10.1204
17.12549
23.10416
15.9175
08.12291
09.12289
03.12287
23.11951
03.11981
03.11977
13.12027
13.13242
15.117
13.4464
Receiver - crank
Tire & Rim 400 / 8 - 4 Ply
Hex Nut 5/8 NF
Washer – 5/8 SS
Spacer - Rubber
Disc - Spacer
Spring - Compression
Link - Upper
Pin - Cylinder
Pin - Short
Link – Lower
Elbow – 04 JIC X 06 ORB
Hydraulic Hose – ¼ X 215”
Hydraulic Hose Clamp
Pioneer Coupler – ½”
1
1
1
1
1
1
1
1
1
1
1
2
1
4
2
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
13.1351
13.13244
13.12049
13.11447
03.13150
14.271
08.13158
14.194
11.13242
15.10620
03.13157
14.239
03.3139
23.13241
23.4612
Reducer Bushing – ¼ X ½
Hydraulic Hose – ¼ X 208”
Orifice .040 04 JIC
Hydraulic Cylinder – 1.5 X 6
Base – Wheel Drive
Bearing – 1” Cast
Shaft – Wheel Drive
Sprocket – 40B20 1” Bore
Driveline – 5500 Single Axle
Tensioner – Chain
Arm – Wheel
Bearing – 1” Ball
Axle – Wheel Drive
Roller Chain #40 NI 124 Rollers (not shown)
Connecting Link #40 NI (not shown)
2
1
1
1
1
2
1
2
1
1
1
4
1
1
1
Page 71
Parts
Page 72
Valmar
Valmar
Parts
CHARLYNN HYDRAULIC METERING DRIVE
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
03.13203
03.13252
04.13206
04.13250
05.13249
05.13174
04.13210
13.5974
13.6146
03.13198
14.13257
05.13213
15.117
23.13241
23.4612
Shield
Spacer - Shield
Plate - Shield
Mount - Shield
Mount – Shield
Base – Hydraulic Motor Mount
Guard – Hydraulic Motor
Hydraulic Motor – Charlynn 101-2146
Fitting – 5/8 ORB
Bracket – Motor Mount
Sprocket – 40B20 – 1”
Bracket – Hose Mount
Clamp – Hydraulic Hose
Chain – Roller #40NI 124 Rollers (not shown)
Connecting Link #40 (not shown)
1
1
1
1
1
1
1
1
2
1
1
1
6
1
1
Page 73
Parts
Page 74
Valmar
Valmar
Parts
RAWSON HYDRAULIC METERING DRIVE
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
03.13203
03.13206
04.13252
04.13250
04.13193
05.13174
04.13210
13.13328
13.8202
13.13254
13.13253
15.117
05.13213
05.13180
13.13317
Shield
Plate - Shield
Spacer - Shield
Mount - Shield
Bracket – Driver Box
Base – Hydraulic Motor Mount
Guard – Hydraulic Drive
Hydraulic Motor – Rawson 3.0 CID
Fitting – 06 ORB X 08 JIC
Hydraulic Hose – ½” X 216” 90°
Hydraulic Hose – ½” X 214” 45°
Clamp – Hydraulic Hose
Bracket – Hose Mount
Bracket – Filter
Filter – Rawson # 305014
1
1
1
1
1
1
1
1
2
1
1
6
1
1
1
16
17
18
19
20
21
22
23
24
25
26
13.13255
13.12401
13.13177
13.13178
13.13179
13.10361
13.4464
13.1351
13.13256
03.13198
05.13249
Hydraulic Hose – ½” X 88”
Fitting – 08 JIC X 12 ORB
Filter Assembly c/w filter Rawson # 703010
Fitting – 10 ORB X ¼ NPT
Diffuser – Rawson # 630601
Gauge – 3000 psi
Coupler – Pioneer male ½”
Reducer Bushing – ½” X ¼” NPT
Hydraulic Hose – ¼” X 216” (Case Drain)
Bracket – Hydraulic Motor Mount
Bracket – Shield Mount
1
1
1
1
1
1
3
1
1
1
1
Page 75
Parts
Page 76
Valmar
Valmar
Parts
FRAME & AXLES (WALKING BEAM)
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
10.4325
10.4592
14.3744
14.3743
14.3742
14.3650
14.3741
17.6058
14.3745
14.3747
17.4596
17.4597
10.5188
10.3749
10.3752
10.4332
Spindle
Hub Assembly – 6 bolt
Seal
Bearing Cone Inner 25580
Bearing Cup Inner 25520
Bearing Cone Outer LM48548
Bearing Cup Outer LM48510
Flat Washer 1” X 2”OD
Dust Cap
Castellated Nut – 1” NF
Wheel Bolt – 9/16 NF
Wheel Nut – 9/16 NF
Rim W7B X 20 – 6 bolt
Rim 16.1 X 14 – 6 bolt
Tire – 16.5L X 16.1
Tire – 9.00 X 20
4
4
4
4
4
4
4
4
4
4
24
24
4
4
4
4
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
03.11886
03.11914
03.11920
03.11961
03.11962
03.11964
23.12144
08.3341
14.3346
10.4260
19.7902
19.7903
14.11106
14.7382
17.11963
Main Frame
Clamp - Axle
Axle - Adjustable
Walking Beam - RH
Walking Beam – LH
PTO Storage Pin
Plate – Clamp
Shaft – Walking Beam
Bronze Bearing
Jack
Tongue
Clevis – Tongue
Hook – 3/8
Safety Chain – 3/8”
U-Bolt ½ X 3 ½
1
4
2
1
1
1
4
2
4
1
1
1
2
2
2
Page 77
Parts
Page 78
Valmar
Valmar
Parts
SINGLE AXLE COMPONENTS
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
03.13145
10.13143
14.13232
14.13229
14.13227
14.13231
14.3747
14.13230
14.13228
10.13226
10.13336
10.13335
Axle Housing
Axle
Seal
Bearing Cone Inner JLM 506849
Bearing Cup Inner JLM 506810
Dust Cap D-8000
Castle Nut – 1” NF
Bearing Cone Outer LM501349
Bearing Cup Outer LM501310
Hub Assembly – 8 Bolt c/w items 3 thru 9
Rim – 22.5 X 16.00 TH2 OFS -1.5
Tire – Alliance Flotation 328 12 Ply
2
2
2
2
2
2
2
2
2
2
2
2
Page 79
Parts
Page 80
Valmar
Valmar
Parts
HOPPER & ROLL TARP
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
03.11827
03.3572
03.3575
09.3966
17.5925
15.7309
03.10379
03.12030
03.12031
15.6989
15.7855
03.12000
23.11999
03.6311
03.6314
17.9640
Hopper – 5500PT
Transport Bracket
Transport Lock
Spring
Bolt – Spring Holder
Rubber Stop
Hatch - Screen
Screen – 5500PT
Screen with Hatchway
Cap – Storage Tube
Storage Tube
Gearbox Cover
Prop – Gearbox Cover
Calibration Crank
Crank Storage
Linch Pin
1
2
2
2
2
2
1
3
1
1
1
1
1
1
1
1
02.4812
02.13052
03.4821
17.13056
03.4823
23.13054
05.3660
05.4881
14.8530
15.4819
15.13053
17.4826
17.4827
15.13058
17.4830
17.13091
17.8531
17.13090
23.10249
02.11101
17.4825
17.13055
15.1482
Roll Tarp Assembly – Shur Lock
Roll Tarp Assembly – Agri-Cover
Roll Return *
Bungi Cord **
Tube c/w Spline 99” *
Roll Tube **
Edge Plate
Stop Plate
U-Joint c/w Lock Pin
Tarp *
Tarp ** 1
U-Clamp *
End Plug *
End Plug **
Crank Handle*
Crank Handle**
Crank Extension*
Crank Extension**
Lock Pin c/w Lanyard
Crank Assembly c/w Handle
Splined Stub Shaft *
Splined Shaft **
Density Scale (not shown)
17
18
19
20
21
22
23
24
25
26
27
28
29
1
1
1
1
1
2
1
1
3
1
1
1
1
1
1
2
1
1
1
1
*For use on Shur-Lock Tarp assemblies only
**For use on Agri-Cover Tarp assemblies only
Page 81
Parts
Page 82
Valmar
Valmar
Parts
CENTER SECTION
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
07.3532
03.4518
17.6465
17.1076
03.4634
17.3579
03.4563
03.3533
14.3837
03.4631
14.3838
23.10923
03.4627
03.3535
03.4521
Hinge Tube
Center Section Support
Grease Zerk - 1/4 Straight
Top Link, RH
Stabilizer Linkage
Top Link, LH
Stabilizer, RH
Stop - Stabilizer
Ball Joint, RH Thread
Center Link Tube
Ball Joint, LH Thread
Spacer Tube
Center Section
Overcenter Tightener Tube
Overcenter Linkage
2
2
4
2
1
2
1
2
2
2
2
8
1
2
2
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
03.4560
03.4561
03.3938
03.3939
04.3552
23.3637
17.4529
03.4550
03.4629
05.4644
05.4645
22.3473
03.4585
17.6181
17.4639
Lever, LH
Lever, RH
Linkage Guide, RH
Linkage Guide, LH
Inlet Tube Holder
Inlet Tube
Hitch Pin Assembly
Baffle
Baffle Guide
SMV Holder
Mounting Plate
SMV Sign
Stabilizer, LH
Grease Zerk, 90 degree
Greasable Bolt 1 x 5 1/2
1
1
1
1
4
10
2
2
4
1
1
1
1
2
2
31
32
33
34
35
36
37
17.4640
17.6046
17.6045
17.6012
03.3874
06.7296
02.4837
Greasable Bolt 3/4 x 5
Jam Nut 3/4 NC
Jam Nut 3/4 NF LH
Jam Nut 3/4 NF
Access Ladder
Mounting Angle
Ladder Assembly
4
2
2
2
1
2
1
Page 83
Parts
Page 84
Valmar
Valmar
Parts
BOOM & BOOM TIP
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
03.6977
09.1087
02.6979
09.3966
07.11773
03.3581
17.4372
17.4371
17.4370
03.3479
03.3480
03.4010
03.4011
03.3512
03.3513
Inner Shock
Spring
Outer Shock
Spring
Bushing
Breakaway Latch
3/8 Cable Clamp
3/8 Cable Thimble
3/8 Cable - 12.25'
Main Boom LH - 40 ft.
Main Boom RH - 40 ft.
Main Boom LH - 36 ft.
Main Boom RH - 36 ft.
Boom Tip LH - 40 ft.
Boom Tip RH - 40 ft.
2
2
2
2
2
2
8
4
2
1
1
1
1
1
1
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
03.4014
03.4015
15.3580
03.3638
23.3511
03.8713
03.8712
03.4636
03.4635
23.4415
17.5925
17.5932
03.4587
17.1788
23.10910
15.1684
Boom Tip LH - 36 ft.
Boom Tip RH - 36 ft.
Breakaway Roller
Hinge Pin
Adjustable Support
Deflector LH
Deflector RH
Center Deflector LH
Center Deflector RH
Hose Clamp, HAS 44
Bolt, 3/8 x 5 NC
Cotterpin, 1/8 x 1
Eye Bolt
Rollpin, 5/32 x 1 1/2
Bushing
Tarp Strap, 9"
1
1
2
2
2
5
5
1
1
22
2
2
2
2
2
2
Page 85
Parts
Valmar
HYDRAULIC BOOM FOLD
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
18.11818
03.12040
03.12048
09.11996
13.11447
13.12027
13.12028
13.12049
13.12050
13.12051
13.1351
13.4464
13.8552
15.117
23.12054
Hydraulic Boom Fold Kit (inc. items 1 thru 13)
Bracket – Boom Fold
Swivel – Boom Fold
spring - Compression
Hydraulic Cylinder 1.5 X 6
Fitting – 06 ORB X 04 JIC Elbow
Fitting – Tee 04 JIC
Orifice - .040 04 JIC
Hydraulic Hose ¼ X 48”
Hydraulic Hose ¼ X 62”
Fitting – NPT ½ X ¼ Reducer
Fitting – Pioneer Male Coupler 8010-4
Hydraulic Hose ¼ X 276”
Clamp – Hydraulic Steel Tube
Pin – ¾”
1
2
2
2
4
2
6
1
1
2
2
2
1
2
Page 86
Valmar
Parts
TAIL LIGHTS
ITEM
PART NO.
1
2
3
4
5
6
7
8
9
16.9534
16.7873
16.9533
16.9532
16.7870
16.7871
16.7872
16.8505
15.7861
DESCRIPTION
Harness - Tail Lights - 4 Wire
Connector - 7 Terminal, SAE J560
Lamp - Dual RH, Wesbar # 2616
Lamp - Dual LH, Wesbar # 2615
Bulb - 12V, # 1157
Lens - Amber, Wesbar # 2650
Lens - Red, Wesbar # 2651
Lens - Black, Wesbar # 2652
Storage Receptacle
QTY
1
1
1
1
4
4
2
2
2
Page 87
Parts
Page 88
Valmar
Valmar
Parts
DISC MARKER
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
05.11291
07.11307
17.7778
17.5854
15.1684
03.12074
03.12075
03.12076
03.12079
03.12084
03.12085
03.12086
03.5863
03.5866
10.5864
03.5852
Plate - Mounting
Bushing
Hitch Pin ½ X 7
Cable
Tarp Strap
Frame – Front Centre
Frame Extension - RH
Frame Extension - LH
Frame - Rear
Strut - Upper
Strut - Outer
Strut - Inner
Depth Control Wheel
Coupler
Disc
Boom
2
4
2
2
2
1
1
1
1
2
2
2
2
2
2
2
17
18
19
20
21
22
23
24
25
26
27
02.5860
03.7377
14.6454
10.6457
14.6458
17.1442
04.6961
14.6455
14.6456
17.1444
03.13352
Axle Assembly
Axle
Grease Seal
Hub Assembly
Dust Cap DC 10
Nut – Axle
Spacer Disc
Bearing Cone L44643
Bearing Cup L44610
Wheel Bolt
Extension – Boom (Single Axle only)
2
2
2
2
2
2
2
4
4
8
2
Page 89
Parts
Page 90
Valmar
Valmar
Parts
DECALS
ITEM
PART NO.
DESCRIPTION
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
02.12141
02.12142
22.11873
22.11874
22.1577
22.3915
22.3917
22.4668
22.4695
22.5840
22.6143
22.7379
22.8614
22.12056
22.12057
22.7876
22.7877
22.13131
Pesticide Chart – Ultra Low / Low
Pesticide Chart – Med / High
5500 PT Decal – Front / Rear
5500 PT Decal - Side
Gearbox Lubrication
General Caution
Rotating Part Hazard
Transport Latch
PTO Hookup
Toxic Chemical
Moving Part Hazard
1000 RPM PTO
Exploding Part Hazard
Fertilizer Chart - Low
Fertilizer Chart - High
Amber Reflector
Red Reflector
Decal – Hydraulic Fan Drive
1
1
2
2
1
1
1
2
1
1
1
1
1
1
1
1
2
1
Page 91