Lindapter Catalogue 09 UK:-

Transcription

Technical Innovation in
Steelwork Connections
Established 1934
Lindapter - Technical Innovation in Steelwork Connections
2
Tel: +44 (0) 1274 521444 www.lindapter.com
Established in 1934 as a small
family business Lindapter has now
become the market leader in
steelwork fixings with a worldwide
reputation; export accounting for
an increasing portion of our
business. Lindapter abides by
Founder
Henry Lindsay
a policy which includes strict
adherence to quality control and EHS procedures;
also offering first class customer service using state
of the art equipment. Continual improvement of
both products and policies ensures that Lindapter
continues to be at the forefront in the marketplace.
All enquiries are dealt with on an individual basis
ensuring that customers receive the correct
technical support together with project specific
drawings in either 2D or 3D formats together with
itemised parts list; all part of a free comprehensive
service.
For situations where standard products are just not
enough the R & D facility can design and develop
new special products to suit individual applications.
Whatever the application all products will meet
Lindapters own exacting standards ensuring that
they are safe, quick and easy to install saving the
customer both time and money by reducing
installed costs. As the vast majority of Lindapter
products require no site drilling or welding steel
sections can, if and when necessary, be reused
ensuring both current and future environmental and
sustainability issues can be met.
In the plant on the opposite page many different
Lindapter applications are outlined.
3
Index
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Service and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Quality and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2 Cavity Fixings
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Type HB - Hollo-Bolt® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Type LB 2 - Lindibolt 2® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
1 Steelwork Fixings
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Girder Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Bolt Length / Tail Length / Installation . . . . . . . . . . . . . . . . . . . . . . . .11
Type A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Type B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Accessories for Type A and B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Plate and Packing Details for Type A and B . . . . . . . . . . . . . . . . . . . .15
Type AF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Type CF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Accessories for Type AF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Plate and Packing Details for Type AF and CF . . . . . . . . . . . . . . . . . .19
Type LR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Type D2 and Type D3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Accessories for Type LR, D2 and D3 . . . . . . . . . . . . . . . . . . . . . . . . .22
Plate and Packing Details for Type LR, D2 and D3 . . . . . . . . . . . . . . .23
Type LS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Accessories / Plate and Packing Details for Type LS . . . . . . . . . . . . .25
Type BR and Type RC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Accessories / Plate and Packing Details for Type BR . . . . . . . . . . . . .27
4
Type Lindapter-HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
3 Composite Decking Fixings
Type BSNT and Type BSLN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Type F9 and Type HW/HC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Type AW - Alphawedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Type SC and Type LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Type MW2 - Multiwedge 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Type FC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Type TR60 and Type VN - V-Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Loads and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Type SD2 - Slimdek 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Technical Enquiry Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Type TC - Toggle Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Decking Fixings Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
4 Support Fixings
6 Appendix
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Section Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Type FLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
General Enquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Type FL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Projects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Type LC and Type SW - Swivel Unit . . . . . . . . . . . . . . . . . . . . . . . . . .57
Type F3 and Type F3-BICC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Type SH and Type HW / HC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Type Z10 and Type HCW30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Type HCW31 and Type WF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Purlin Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Factors of safety shown in this catalogue are typical values and
vary with different products from 2:1 to 5:1.
Stated tightening torques must not be exceeded.
Type HCW34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Disclaimer
Lindapter International supplies components in good faith, on the
assumption that customers fully understand the loadings, safety factors
and physical parameters of the products involved. Customers or users
who are unaware or unsure of any details should refer to Lindapter
International before use. Responsibility for loss, damage, or other
consequences of mis-use cannot be accepted. Lindapter makes every
effort to ensure that technical specifications and other product
descriptions are correct. ‘Specification’ shall mean the specification
(relating to the use of the materials) set out in the quotation given by the
Seller to the Buyer. Responsibility for errors or omissions cannot be
accepted. All dimensions stated are subject to production tolerances if in doubt please check with Lindapter.
Applications
All the applications featured in the catalogue are based on real
projects. More information about these can be found on our website
www.lindapter.com.
© Lindapter 2009 © Lindapter International
© Lindapter is a registered trade mark
5 Floor Fixings
In the interests of improving the quality and performance of Lindapter
products, we reserve the right to make specification changes without
prior notice.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Type FF - Floorfast® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Type GF - Grate-Fast® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Type GF3030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
5
Service and Support
Research and Development
To meet the needs of a fast changing world Lindapter’s Research and
Development Department works to develop new generic products.
The team is supported by the latest computer aided design (CAD)
techniques such as 3D modelling, rapid prototyping and finite element
analysis; new products are tested in house on Lindapter’s own 1,000kN
hydraulic test machine.
This unique technical expertise is supported by Lindapter’s collaboration
with respected companies and organisations such as Corus, Mannesmann,
The Steel Construction Institute, CIDECT as well as many leading
universities and approval bodies.
Engineered Solutions
Developing products that meet the needs of a particular project is
another Lindapter strength.
The service offered to clients includes:
• Design and development of custom products for unique projects
• Individual test runs and reports
Bespoke solution
for sign fixings
• Detailed drawings and/or solid models
• Full strength and performance analysis
• Trial runs and on site consultation
Customer Technical Support
For our existing product range Lindapter’s Technical Sales and Support
Department offers customers full support for any project, large or small;
this free of charge service includes:
• Assembly solutions optimised for cost and performance
• Coating and corrosion recommendations
• Load analysis on Lindapter connections
• On site technical advice and support
• 2D AutoCAD and 3D SolidWorks drawings
• Contractor training
• Bills of Materials
• CPD Presentations
Sample Project
Seedhill Bridge, Lancashire, England
Bridge refurbishment:
Due to the age and condition of the structure the use of welded shear
studs was not possible. Instead modified Hollo-Bolts® were used which
enabled the bridge deck refurbishment to be completed on time and to
specification.
For further information regarding this project see website
www.lindapter.com.
6
Special Hollo-Bolt®
Standard Hollo-Bolt®
Quality and Approvals
Quality
Approvals for sprinkler products
Product quality is one of the main life lines
of the Lindapter philosophy, the entire
company is particularly dedicated to this
aspect. Lindapter has been accredited to
BS EN ISO 9001 since 1986.
The American Insurance Association, Factory Mutual,
offers an approval which is recognised by the fire
protection industry world-wide.
Q 05143
Approvals
Lindapter has been trading internationally for many years respecting
the market differences around the world. The relevant international
authorities have granted many product approvals over time.
The catalogue refers to them product by product.
Approvals for construction
The Deutsches Institut für Bautechnik, Berlin is a body
which approves products and materials for use in
structural engineering applications in the construction
and civil engineering industries in Germany.
Lloyds Register Type Approved products have been
subjected to tensile, frictional, shear, vibration and
shock tests, witnessed and verified by Lloyds
Register.
The TÜV is the certifying authority for safety,
quality and environmental protection in Germany.
Det Norske Veritas has approved the use of Lindapter
products in lifting applications. This includes their use
on both mobile and fixed offshore installations.
Verband der Schadenversicherer e.V. is a German
insurance association who also offers a rigorous
approval for products used in the fire protection
industry.
These approvals serve to reinforce Lindapter’s extensive in-house
testing procedures. Lindapter products are tested so that the user can
be confident whether specifying or using that Lindapter products will
perform as per the information detailed in this catalogue. Loads
published are the product safe working loads, taking into account a
factor of safety.
Corrosion Protection
Lindapter products are delivered as standard either bright zinc plated
or hot dip galvanised. Various other coatings and alternative materials
are available upon request for most products including:
• Sheradising
• Delta seal
• Mechanical galvanising
• Delta tone
• Plastic coating
• Sheraplex
• Special paint coating
• Stainless steel
Lindapter is a member of the following organisations:
British Constructional
Steelwork Association
The Steel Construction
Institute
The Building Services Research
and Information Association
7
8
Steelwork Fixings
1
Steelwork Fixings
Lindapter Steelwork Fixings can be used in a wide
variety of applications for connecting together steel
sections of whatever shape and size; uppermost in
this section is the Girder Clamp which, as with
most Lindapter products, needs no on site drilling
or welding saving both time and money by reducing
installed costs. Numerous world wide project
successes have demonstrated that this is ideally
suited for both new construction and refurbishment
of existing structures.
Advantages
• Reduces design time
• Guaranteed loads and approvals
• No on-site drilling or welding
• ‘Hot Working’ not required
• Less work at height
• Only hand tools required to install
• Site adjustable
• Power not required
• Ability to deconstruct and multi-cycle
rather than demolish
Markets include:
• Plant Engineering
• Chemical and Petro-chemical Industry
• Materials Handling
• Structural Engineering
• Civil Engineering
• Facades
• Theatre Equipment
• Transportation
• Offshore
Applications include:
• Steel Constructions
• Cranes
• Lifting Beams
• Pipe Supports
• Towers and Masts
9
Steelwork Fixings
Girder Clamps
Components of a Girder Clamp
1. Standard Grade 8 Hex Nut
2. Standard Hardened Washer
3. Lindapter Clamp
Dependent on the application different clamps could be used i.e.
Types A, B, BR, AF, LR, LS, D2 or D3.
1
4. Packing Piece
In combination with the clamps mentioned above these parts
increase the tail length to enable the product to sit correctly on the
beam.
2
3
5. Location Plate (can be supplied if required)
This is an essential part of the girder clamp assembly that enables
all the components to be located in the correct position. The hole
centres and plate thickness are calculated to suit the individual
application.
4
6. Lindapter Clamp
This can be of a similar type as 3 (above), although certain products
are designed to specifically work together i.e. A + B.
5
7. Standard Grade 8.8 Hex Bolt or Setscrew
6
Loads
7
The table beneath shows tensile and frictional load capabilities for a
standard four bolt Girder Clamp using 4 bolts and 8 clamps at a 90°
crossover angle. Lindapter is only too pleased to carry out all design work
for individual connections free of charge based on the following details:
•
•
•
•
•
Load per connection
Size and type of both beams
Angle of crossover
Distance between beams
Inclination of beams
Clamps
Bolt size
Bolt grade
Tensile / for 4 bolts
Friction / for 4 bolts
Torque
kN
kN
Nm
M12
8.8
23.2
1.4
69
Types A, B, BR, LR
M16
M20
8.8
8.8
29.2
59.0
3.0
6.0
147
285
Type AF
M24
8.8
78.8
9.0
491
M24
8.8
160.0
60.02)
800
M24
10.9
250.01)
70.02)
1000
1) Factor of safety 3.2:1
2) Factor of safety 2:1
All loads are based on actual test data having a factor of safety for friction against slip and for tensile against ultimate failure
(typically 5:1). Use of lower safety factor is not recommended.
Approvals
All approvals apply to Girder Clamps using types A and B only, in sizes from M12 to M24 Further information is available upon request.
10
1
Steelwork Fixings
Bolt Length / Tail Length / Installation
Bolt length calculation for a
standard Lindapter Girder Clamp,
example shows Type A and B M20
1
Tail length
The different tail length can be identified by a code of dimples
underneath the clamps.
To calculate the bolt length all parts the bolt will go through have to
be added up. The next longer standard bolt length should be used.
One dimple:
tail length short (s)
0.5 · bolt Ø
as bolt protrusion
10
Height of nut
16
+ Washer
3
+ T of top clamp
20
Two dimples:
tail length medium (m)
12.5
+ Top section
+ Plate thickness
12
+ Lower section
10
+ T of lower clamp
10
Three dimples:
tail length long (l )
Next standard
bolt length
=
93.5
=
100.0
Correct installation of types A and B
showing type A as an example
Parallel flanges
90º
>90º
<90º
Maximum tail length tolerance of -1mm (up to M16) and -1.5mm (M20, M24) before applying the torque is acceptable.
Tapered flanges
<_5º
90º
<90º
5-8º
On 6º and 8º slopes types A and B require a special tail length/packing combination which will allow the clamp to tilt back slightly (incorporated into the
combination table on page 15).
For applications above 8° please see types AF, LR and LS.
11
1
Steelwork Fixings
Type A
Type A
Malleable iron, bright zinc plated / hot dip galvanised
Nose
Recess
Clamping Area K
Skirt
Tail
T
V
Y
X
Z
Typical Applications
(see also page 36-39)
Product
Code
Steelwork clamp with recessed top to hold the bolt head captive whilst
the nut is tightened. The skirt prevents the clamp rotating during
installation. Suitable for flanges up to 8°.
The clamp is installed correctly when the area ‘K’ grips the flange.
The tail must be chosen to suit the thickness of the flange being
gripped. For correct tail length/packing combinations please see
page 15.
Bolt 8.8
Z
Safe Working Loads
(5:1 Factor of Safety)
Tensile / 1 Bolt
Frictional / 2 Bolts
kN
kN
1.0
-
Torque
Nm
6
Y
mm
16
X
mm
8
Dimensions
Tail Length V
short medium long
mm
mm
mm
4
-
T
mm
4
Width
mm
20
A08
M8
A10
M10
1.5
-
20
20
11
4
5
7
5
26
A12
M12
5.8
0.7
69
26
13
4.5
6
9.5
6
29
A16
M16
7.3
1.5
147
30
16
5.5
8
11
8
36
A20
M20
14.7
3
285
36
19
7
10
12.5
10
46
A24
M24
19.7
4.5
491
48
25
9
12
16
12
55
For higher loads the type AF should be used (see page 16).
Order example: A16 medium HDG
12
Steelwork Fixings
Type B
1
Type B
Flat Top
Nose
Clamping
Area K
Skirt
Tail
Z
T
V
Y
X
Steelwork clamp with flat top which allows the bolt head or
nut to be rotated. Suitable for use with all bolts, studs, tie
rods and J-bolts, and flanges up to 8°.
The clamp is installed correctly when the area ‘K’ grips the
flange. The tail must be chosen to suit the thickness of the
flange being gripped. For correct tail length/packing
combinations please see page 15.
Product
Code
Bolt 8.8
Z
Safe Working Loads
Tensile / 1 Bolt
kN
kN
1.0
-
Torque
Nm
6
Y
mm
16
X
mm
8
Dimensions
Tail Length V
short medium long
mm
mm
mm
4
-
T
mm
8
Width
mm
20
B08
M8
B10
M10
1.5
-
20
20
11
4
5
7
10
26
B12
M12
5.8
0.7
69
26
13
4.5
6
9.5
12
29
B16
M16
7.3
1.5
147
30
16
5.5
8
11
16
36
B20
M20
14.7
3
285
36
19
7
10
12.5
20
46
B24
M24
19.7
4.5
491
48
25
9
12
16
24
55
For higher loads the type AF should be used (see page 16).
Order example: B16 medium HDG
13
Steelwork Fixings
Accessories for Type A and B
Type CW - Clipped Washer
Mild Steel, bright zinc plated /
hot dip galvanised
T
Y
X
Z
Packing used to adjust the tail length of the clamp to meet
differing beam flange thicknesses.
Product
Code
Bolt
Z
Dimensions
X
T
mm
mm
9,5
2
CW08
M8
Y
mm
4
Width
mm
19
CW10
M10
5
14
2
CW12
M12
6
19.5
2.5
31
CW16
M16
8
17.5
3
38
CW20
M20
10
22
4
44
CW24
M24
12
29
4
57
25
Order example: CW08 BZP
Type P1 short / P2 short
Mild Steel, malleable iron,
bright zinc plated / hot dip galvanised
TP1
Y
TP2
X
Z
Product
Code
P1
P2
P1S08 P2S08
Bolt
Z
P1S10
P1S12
Dimensions
TP1 TP2
mm mm
4
8
Width
mm
21
M8
Y
mm
4
X
mm
10
P2S10
M10
5
13
5
10
24
P2S12
M12
6
16
6
12
30
P1S16
P2S16
M16
8
21
8
16
35
P1S20
P2S20
M20
10
23
10
20
43
P1S24
P2S24
M24
12
32
12
24
54
Order example: P1S16 HDG
Type T
Malleable iron, bright zinc plated /
hot dip galvanised
T
Z
To fill the nose of type A and B making it horizontal. For parallel flanges
only. The thickness ‘T’ should be added for tail length and bolt length
calculations. The product is for aesthetic purposes only and technically
not necessary.
Product
Code
Bolt
Z
T12
M12
Dimensions
T
mm
3
T16
M16
4
T20
M20
5
T24
M24
6.5
Bolt
Z
Order example: T12 BZP
Type W
Mild Steel, malleable iron, bright zinc plated /
hot dip galvanised
T
Z
Washer to fill the recess of type A to enable the nut to be tightened.
When calculating the bolt length please add ‘T’.
14
Product
Code
W08
M8
Dimensions
T
mm
4
W10
M10
5.5
W12
M12
6.5
W16
M16
8
W20
M20
9.5
Order example: W08 BZP
1
Steelwork Fixings
Plate and Packing Details for Type A and B
L1
L1
l1M
Location and End Plates
l1M
b1
L1 =
Plate length
L2 =
Plate width
l1M, l2M =
Hole centres
b1, b2 =
d=
s=
Flange width
Hole Ø
Plate thickness
1
b1
l2M
b2
L2
l2M L2
d
d
Location Plate
End Plate
Plate Dimensions
Material: Mild Steel Grade S275 JR (for other grades please contact Lindapter)
End Plate1)
Location Plate
M8
Hole Ø
d
mm
9
Plate
Thickness
s
mm
6
M10
11
8
b + 11
M12
13
8
b + 13
M16
18
10
M20
22
M24
26
Bolt
Z
Plate
Thickness
s
mm
10
Hole Centre
l1M
mm
b1 + 9
Length
min L1
mm
b1 + 36
Hole Centre
min l2M
mm
40
Width
min L2
mm
l2M + 40
b + 44
12
b1 + 11
b1 + 44
50
l2M + 40
b + 54
12
b1 + 13
b1 + 54
60
l2M + 50
b + 18
b + 70
15
b1 + 18
b1 + 70
70
l2M + 60
12
b + 22
b + 88
20
b1 + 22
b1 + 88
90
l2M + 70
15
b + 26
b + 104
25
b1 + 26
b1 + 104
110
l2M + 90
Hole Centres
l1M, l2M
mm
b+9
Length/Width
min L1, min L2
mm
b + 36
1) Dependant on the use of the end plate the thickness might need to be increased.
Calculation of bolt length see page 11
Tail Length / Packing Combinations
for Types A & B
for Types A & B
For beams up to and including 5° slope
For IPN-Beams of an 8° slope
Flange
Thickness
M12
mm A,B CW P1S P2S
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
28
30
s
m
s
s
m
l
m
l
s
s
l
l
m
m
s
s
m
l
s
m
s
s
l
m
1
1
1
2
1
1
1
2
2
1
1
1
1
1
-
1
1
1
1
1
1
1
1
1
-
1
1
1
1
1
1
1
1
1
1
2
Types A & B
M16
A,B CW P1S P2S
s
s
m
m
s
l
l
s
s
l
s
m
l
l
l
l
l
l
l
m
l
l
s
l
1
2
1
3
2
2
3
3
1
1
2
2
2
1
1
1
1
1
1
1
1
-
1
1
1
M20
A,B CW P1S P2S
■
■
s
s
m
m
s
s
l
m
s
s
s
m
s
m
s
m
l
m
s
s
m
m
1
1
1
2
2
2
3
1
3
1
2
2
2
-
1
1
1
1
1
1
1
1
-
1
IPN
M12
Profile A,B CW P1S P2S
M24
A,B CW P1S P2S
■
■
■
▲
s
s
m
m
s
s
l
l
s
s
l
l
s
s
m
m
s
s
l
s
1
1
2
2
1
1
1
1
2
1
1
1
1
1
1
1
1
80
100
120
140
160
180
200
220
240
260
280
300
320
340
360
380
400
425
450
475
500
550
600
-
■
■
s
s
m
m
s
s
m
m
l
s
m
l
s
m
l
▲
▲
▲
▲
▲
▲
1
1
1
1
2
1
1
3
2
-
1
1
-
-
Types A & B
M16
M20
A,B CW P1S P2S A,B CW P1S P2S
■
■
■
■
s
s
▲
▲
m
m
▲
▲
l
l
▲
s
l
m
m
▲
▲
▲
▲
1
-
1
1
1
-
-
■
■
■
■
■
■
■
s s ▲
m m s 1
l l ▲
▲
▲
▲
▲
▲
▲
■
-
-
M24
A,B CW P1S P2S
■
■
■
■
■
■
■
■
■
s s s ▲
m m s 1
▲
▲
l l ▲
▲
■
-
-
For thicker flanges please contact Lindapter.
s = short
m = medium
l = long
P1S = P1 short
P2S = P2 short
■
= Type not applicable
▲
= Please contact Lindapter
15
1
Steelwork Fixings
Type AF
Type AF
SG iron, hot dip galvanised
Without washer: For bolt grade 8.8
Recess
Nose
Skirt
Tail
With washer Type AFW
Flat Top
T
V
Y
X
With washer inverted Type AFW
for bolt grade 10.9 with larger hexagons
(M12 - M20)
Z
High friction clamp with recessed top to hold bolt head captive whilst
the nut is tightened. Can be combined with type CF. The skirt prevents
the clamp rotating during installation. The tail of the AF spans across
slotted holes. For flanges up to 10°. Washer type AFW available
(see illustration).
For correct tail length/packing combinations please see page 18.
Product
Code
Z
Grade
AF12
M12
8.8
AF16
M16
8.8
16.0
8.0
AF20
M20
8.8
26.3
13.0
AF24
M24
8.8
40.0
24.0
AF12
M12
10.94)
10.0
4.0
5.2
130
29
AF16
M16
10.94)
19.5
11.0
12.0
300
35
AF20
M20
10.94)
30.0
20.0
25.0
647
40
M24
4)
28.0
35.0
1000
48
AF24
1)
2)
3)
4)
Bolt
Safe Working Loads
(5:1)
Factor of Safety (2:1)
Tensile / 1 Bolt
Frictional1) / 2 Bolts
Painted Steelwork2)
Galv. Steelwork
kN
kN
kN
8.5
3.4
3.9
10.9
3)
62.5
Dimensions
Tail Length V
T
short medium Type AF Type AF with AFW Width
mm mm
mm
mm
mm
5
12.5
17
22
39
Torque
Nm
90
Y
mm
29
X
mm
27
10.0
240
35
37
8
15
22
27
49
16.0
470
40
39
10
18
25
31
56
30.0
800
48
60
15
30
32
42
82
27
5
12.5
17
22
39
37
8
15
22
27
49
39
10
18
25
31
56
60
15
30
32
42
82
Frictional Load figures are based on Type AF and Location plates in hot dip galvanised finish
Shot blast and painted steelwork
3.2:1 factor of safety
For HR or HV bolts (hot dip galvanised and lubricated) please refer to manufacturers’ recommendation for torque figures.
Order example: AF12 short
16
Steelwork Fixings
Type CF
1
Type CF
SG iron, hot dip galvanised
Anti-rotation markings
Nose
Legs
Y
Y
X
X
min T
max T
V
Z
Z
min t
max t
High friction clamp which hooks over flanges of I-beams, angles and
channels. Lindapter markings act as a unique anti-rotation device.
Can be combined with all Lindapter Girder Clamp products including
type AF.
Product
Code
Bolt 8.8
Z
(5:1)
Tensile / 1 Bolt
Safe Working Loads
factor of safety (2:1)
Frictional1) / 2 Bolts
Galv. Steelwork
Painted Steelwork2)
kN
kN
3.4
3.9
Torque
Nm
90
Y
mm
32
X
mm
14
Dimensions
t
T
mm
mm
6 - 13 21 - 29
V
mm
25
Width
mm
46
CF12
M12
kN
8.5
CF16
M16
16.0
8.0
10.0
240
44
18
8 - 16 25 - 33
32
56
CF20
M20
26.3
13.0
16.0
470
53
22
10 - 19 30 - 41
45
65
kN
0.7
1.7
Nm
69
147
285
CF / A3)
CF / A3)
M12
M16
CF Combinations with other Lindapter Clamps
kN
kN
5.8
0.7
7.3
1.5
Order example: CF12
CF / A3)
M20
14.7
3
3.0
CF / AF
M12
8.5
3.4
3.9
90
CF / AF
M16
16.0
8.0
10.0
240
CF / AF
M20
26.3
13.0
16.0
470
1) Frictional load figures are based on type CF and location plate in HDG finish
2) Shot blast and painted steelwork
3) Also applies to type B, BR, LR, D2 or D3
17
Steelwork Fixings
Accessories for Type AF
Type AFCW
Mild Steel, hot dip galvanised
T
Y
X
Product
Code
Bolt
Z
AF12CW
M12
Dimensions
X
T
mm
mm
33
2
Y
mm
7
Width
mm
40
AF16CW
M16
8
40
2
50
AF20CW
M20
9.5
40.5
2
55
Order example: AF12CW
Packing used to adjust the tail length of
the clamp to meet differing beam flange
thicknesses; has a slight bend along its
centre line which flattens out during
installation.
Z
Type AFP1 / AFP2
Mild Steel, hot dip galvanised
T
Y
X
Z
Product
Code
P1
P2
AF12P1 AF12P2
AF16P1 AF16P2
Bolt
Z
Dimensions
TP1 TP2
mm mm
5
10
Width
mm
40
M12
Y
mm
7
X
mm
33
M16
8
42
AF20P1 AF20P2
M20
9.5
45.5
5
10
56
AF24P1 AF24P2
M24
12
73
5
10
85
5
10
52
Order example: AF12P1
Packing used to adjust the tail
length of the clamp to meet
Type AFW
SG iron, malleable iron, hot dip galvanised
T
Z
Washer filling the recess of the type AF.
Product
Code
Bolt
Z
AFW12
M12
Dimensions
T
mm
5
AFW16
M16
5
AFW20
M20
6
AFW24
M24
10
Order example: AFW12
Additionally it features two projections
which, when the AFW is inverted, will
captivate the larger hexagons of 10.9
bolts. (M12 – M20 only).
T
M24 version has no projections.
Z
18
1
L1
L1 =
Plate length
L2 =
Plate width
l1M, l2M =
Hole centres
b1, b2 =
d=
s=
Flange width
Hole Ø
Plate thickness
L1
l1M
1
Steelwork Fixings
Plate and Packing Details for Type AF and CF
l1M
b1
b1
b2
l2M
L2
l2M L2
d
d
Location Plate
End Plate
Plate Dimensions
Material: Mild Steel Grade S355 JR (for other grades please contact Lindapter)
End Plate1)
Location Plate
M12
Hole Ø
d
mm
13
Plate
Thickness
s
mm
10
M16
18
15
b + 18
M20
22
20
b + 22
M24
26
25
b + 26
Bolt
Z
Hole Centres
l1M, l2M
mm
b + 13
Plate
Thickness
s
mm
15
Hole Centre
l1M
mm
b1 + 13
Length
min L1
mm
b1 + 90
Hole Centre
min l2M
mm
80
Width
min L2
mm
l2M + 80
b + 110
25
b1 + 18
b1 + 110
100
l2M + 100
b + 130
30
b1 + 22
b1 + 130
180
l2M + 180
b + 180
40
b1 + 26
b1 + 180
200
l2M + 200
Length/Width
min L1, min L2
mm
b + 90
2) For combinations of Type CF with A, B and BR see page 15 and for types D2, D3 and LR see page 23.
Tail Length / Packing Combinations for Types AF
Parallel flanges and beams of up to 10º slope
Flange
Thickness
M12
mm AF AFCW AFP1 AFP2
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
s = short
s
s
s
s
s
s
s
s
m
m
s
m
m
m
m
s
m
m
m
m
s
m
m
1
1
2
3
1
1
2
1
2
2
1
2
2
1
1
1
1
1
1
1
1
-
m = medium
1
1
1
1
2
1
1
■
Type AF
M16
M20
AF AFCW AFP1 AFP2 AF AFCW AFP1 AFP2
M24
AF AFP1 AFP2
■
■
■
s
s
s
s
s
s
s
s
m
m
m
s
m
m
m
m
m
m
m
m
m
1
1
2
3
1
1
1
1
1
1
1
1
1
1
-
1
1
1
1
1
■
■
■
■
s
s
s
s
s
s
s
s
m
m
m
m
m
m
m
m
m
s
s
1
1
2
3
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
■
■
■
■
■
■
s
s
s
s
s
s
s
s
s
s
s
s
s
s
s
m
1
1
1
1
1
-
1
1
1
1
-
Flange
Thickness
M12
mm AF AFCW AFP1 AFP2
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
m
m
s
s
m
m
m
s
s
m
m
m
s
s
m
m
m
s
s
m
m
s
s
1
1
1
1
-
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
3
3
2
2
2
3
3
3
3
3
4
4
3
3
4
4
Type AF
M16
M20
AF AFCW AFP1 AFP2 AF AFCW AFP1 AFP2
M24
AF AFP1 AFP2
s
m
m
m
m
m
m
m
m
m
s
m
m
m
m
s
m
m
m
m
s
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
1
1
1
1
1
-
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
2
3
2
2
2
2
3
3
3
3
3
4
3
3
m
m
m
m
m
m
m
s
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
1
1
1
1
1
1
1
2
1
2
2
2
2
2
2
2
2
2
2
3
3
3
3
1
1
1
1
1
1
1
1
1
1
1
-
1
1
1
1
1
1
1
1
1
1
2
2
2
19
Steelwork Fixings
Type LR
1
Type LR
Saddle
Slot
Nose
Leg
Clip
Tail
max Y
min X
max T
min V
Z
min Y
max X
min T
max V
Z
Self adjusting clamp for various flange thicknesses and slopes up
to 15°. The leg of the saddle prevents the clamp rotating during
installation. The LR tail spans slotted holes. For thicker flanges
packings P1 long and P2 long are available. For correct tail
length/packing combinations please see page 23.
Product
Code
Bolt 8.8
Z
Safe Working Loads
Tensile / 1 Bolt
kN
kN
1.5
-
Torque
Nm
20
Clamping Range
V
mm
3 - 10
Y
mm
21 - 24
Dimensions
X
T
Width with Saddle
mm
mm
mm
24 - 26
21 - 24
33
LR10
M10
LR12
M12
5.8
0.7
69
3 - 12
26 - 29
25 - 31
25 - 29
LR16
M16
7.3
1.5
147
3 - 16
30 - 35
34 - 37
30 - 36
46
LR20
M20
14.7
3
285
3 - 20
42 - 49
46 - 51
41 - 48
57
LR24
M24
19.7
4.5
491
3 - 24
47 - 57
52 - 58
44 - 54
76
39
Order example: LR10 BZP
20
Steelwork Fixings
Type D2 / Type D3
1
Type D2
Malleable iron, bright zinc plated,
hot dip galvanised
S
Recess
T
Nose
V
Setscrew
Tail
Y
Clamping
Area K
X
Skirt
Z
Type D3
Malleable iron, bright zinc plated,
hot dip galvanised
Z
S
Flat Top
T
V
Y
X
Adjustable clamps incorporate a setscrew to accommodate a wide
range of flange thicknesses. Type D2 has a recessed head to hold the
bolt head captive. The skirt prevents the clamp rotating during
installation. For flanges up to 5°. For thicker flanges packings P1 long
and P2 long are available. For correct tail length/packing combinations
please see page 23.
Correct Installation: Setscrew S needs to be adjusted so that V is
1mm shorter than the flange thickness prior to installation. Adjust the
setscrew after installation so that the bolt Z is 90° to the clamp and the
clamp contacts the flange with area ‘K’ only.
Product
Code
Bolt 8.8
Z
D210
M10
D212
M12
D216
D220
Safe Working Loads
Tensile / 1 Bolt
kN
kN
1.5
-
Torque
Nm
20
Clamping Range
V2)
V1)
mm
mm
5 - 10
10 - 20
Y
mm
20
X
mm
20
5.8
0.7
69
5 - 10
10 - 22
26
25
M16
7.3
1.5
147
6.5 - 13
13 - 20
30
30
M20
14.7
3
285
8.5 - 17
17 - 24
36
35
D224
M24
19.7
4.5
491
10 - 19
19 - 30
48
49
D312
M12
5.8
0.7
69
5 - 10
10 - 22
26
D316
M16
7.3
1.5
147
6.5 - 13
13 - 20
30
Dimensions
S
T
mm
mm
M6
5
M6
Width
mm
26
6
29
M8
8
35
M10
10
42
M12
12
54
25
M6
12
29
30
M8
16
35
1) Setscrew S inserted from above.
2) Setscrew S inserted from below.
Order example: D210 BZP
21
Steelwork Fixings
Accessories for Type LR, D2 and D3
Type P1 long / P2 long
Mild Steel, malleable iron, bright zinc plated / hot dip galvanised
TP1
Y
TP2
X
Z
Product
Code
P1
P2
P1L10 P2L10
P1L12
P2L12
P1L16
P2L16
P1L20
P1L24
Bolt
Z
Dimensions
TP2
TP1
mm
mm
5
10
Width
mm
24
M10
Y
mm
5
X
mm
24
M12
6
32
6
12
M16
8
40
8
16
35
P2L20
M20
10
47
10
20
43
P2L24
M24
12
64
12
24
54
30
Order example: P1L10 BZP
Packing used to adjust the tail length of
the clamp to meet differing beam flange
thicknesses.
Type T
hot dip galvanised
T
Z
To fill the nose of type D2 and D3 making it
horizontal. For parallel flanges only.
The thickness ‘T’ should be added for tail
length and bolt length calculations. The product
is for aesthetic purposes only and technically
not necessary.
Product
Code
Bolt
Z
T12
M12
Dimensions
T
mm
3
T16
M16
4
T20
M20
5
T24
M24
6.5
Bolt
Z
Order example: T12 BZP
Type W
hot dip galvanised
Product
Code
T
Washer to fill the recess of type D2 to
enable the nut to be tightened. When
calculating the bolt length please add ‘T’.
22
Z
W08
M8
Dimensions
T
mm
4
W10
M10
5.5
W12
M12
6.5
W16
M16
8
W20
M20
9.5
Order example: W08 BZP
1
L1
L1
l1M
l1M
b1
L1 =
Plate length
L2 =
Plate width
l1M, l2M =
Hole centres
b1, b2 =
d=
s=
Flange width
Hole Ø
Plate thickness
1
Steelwork Fixings
Plate and Packing Details for Type LR, D2 and D3
b1
l2M
b2
L2
l2M L2
d
d
Location Plate
End Plate
Plate Dimensions
Material: Mild Steel Grade S275 JR
End Plate1)
Location Plate
M10
Hole Ø
d
mm
11
Plate
Thickness
s
mm
12
M12
13
12
b + 13
M16
18
15
b + 18
M20
22
20
M24
26
25
Bolt
Z
Plate
Thickness
s
mm
15
Hole Centre
l1M
mm
b1 + 11
Length
min L1
mm
b1 + 66
b + 81
15
b1 + 13
b + 105
20
b1 + 18
b + 22
b + 132
25
b + 26
b + 156
30
Hole Centres
l1M, l2M
mm
b + 11
Length/Width
min L1, min L2
mm
b + 66
Hole Centre
min l2M
mm
70
Width
min L2
mm
l2M + 50
b1 + 81
80
l2M + 60
b1 + 105
100
l2M + 70
b1 + 22
b1 + 132
120
l2M + 90
b1 + 26
b1 + 156
150
l2M + 110
for Type LR
for Type LR
Parallel flanges
For IPN-Beams of an 8° slope
Type
Combinations
LR P1L P2L
M 10
M 12
M 24
IPN
M10
Profile LR P1L P2L
M12
LR P1L P2L
M16
LR P1L P2L
M20
LR P1L P2L
M24
LR P1L P2L
mm
80
100
120
140
160
180
200
220
240
260
280
300
320
340
360
380
400
425
450
475
500
550
600
■
■
■
■
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
mm
M 16
M 20
Clamping Range
mm
mm
mm
1
-
-
3 - 10
3 - 12
3 - 16
3 - 20
3 - 24
1
1
-
8 - 15
9 - 18
11 - 24
13 - 30
15 - 36
1
-
1
13 - 20
15 - 24
19 - 32
23 - 40
27 - 48
1
1
1
18 - 25
21 - 30
27 - 40
33 - 50
39 - 60
1
-
2
23 - 30
27 - 36
35 - 48
43 - 60
51 - 72
1
1
2
28 - 35
33 - 42
43 - 56
53 - 70
63 - 84
1
-
3
33 - 40
39 - 48
51 - 64
63 - 80
75 - 96
for Type D2 & D3
Parallel flanges and beams of up to 5° slope
Type
M 10
D2
mm
M 16
M 20
D2 / D3
D2
Clamping Range
mm
mm
mm
-
-
5 - 10
5 - 10
6.5 - 13
8.5 - 17
10 - 19
1
-
-
10 - 20
10 - 22
13 - 20
17 - 24
19 - 30
1
1
-
15 - 25
16 - 28
21 - 28
27 - 34
31 - 42
1
-
1
20 - 30
22 - 34
29 - 36
37 - 44
43 - 54
1
1
1
25 - 35
28 - 40
37 - 44
47 - 54
55 - 66
1
-
2
30 - 40
34 - 46
45 - 52
57 - 64
67 - 78
1
1
2
35 - 45
40 - 52
53 - 60
67 - 74
79 - 90
1
-
3
40 - 50
46 - 58
61 - 68
77 - 84
91 - 102
Combinations
D P1L P2L
11)
M 12
D2 / D3
M 24
D2
mm
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
■
P1L = P1 long
1
1
1
1
1
1
1
1
1
-
1
1
1
1
1
1
1
1
-
P2L = P2 long
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
■
■
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
1
1
■
■
■
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
■
■
■
■
■
■
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
For thicker flanges please contact Lindapter.
1) Setscrew S inverted.
23
Steelwork Fixings
Type LS
1
Type LS
Cast Stainless Steel equivalent to Grade 316
Nose
Tail
min Y
max X
max T
min V
Z
max Y
min X
min T
max V
Z
Self adjusting clamp for various flange thicknesses and slopes up to 10°.
The special serrations on the tail prevent the clamp rotating during
installation. The LS tail spans over slotted holes.
Safe Working Load
(5:1)
Factor of Safety (2:1)
Tensile / 1 Bolt
kN
kN
3.0
1.5
Clamping
Range
V
mm
3 - 15
Product
Code
Bolt A4-70
Z
LS10
M10
LS12
M12
7.0
2.0
80
3 - 20
16 - 22
18 - 29
17 - 23
40
LS16
M16
10.0
3.0
200
3 - 25
22 - 25
27 - 37
20 - 28
55
LS20
M20
18.0
5.0
400
3 - 30
24 - 31
25 - 42
23 - 32
60
Torque
Nm
40
Y
mm
17 - 19
Dimensions
X
T
mm
mm
18 - 24
16 - 21
Width
mm
38
Order example: LS10
24
Steelwork Fixings
Accessories / Plate and Packing Details for Type LS
1
Accessories
Packings are available upon request.
L1
L1
l1M
l1M
b1
L1 =
b1
Plate length
b2
L2 =
Plate width
l1M, l2M =
Hole centres
b1, b2 =
d=
s=
Flange width
Hole Ø
Plate thickness
l2M
L2
l2M L2
d
d
Location Plate
End Plate
Plate Dimensions
Material: Mild Steel Grade S275 JR or S355 JR
End Plate1)
Location Plate
Bolt
Z
Plate Thickness
S275
S355
s
s
mm
mm
8
8
Hole Centres Length/Width
l1M, l2M
min L1, min L2
mm
mm
b + 11
b + 70
Plate Thickness
S275
S355
s
s
mm
mm
12
12
M10
Hole Ø
d
mm
11
Hole Centre
l1M
mm
b + 11
Length
min L1
mm
b + 70
Hole Centre
min l2M
mm
80
Width
min L2
mm
l2M + 60
M12
13
12
10
b + 13
b + 80
20
15
b + 13
b + 80
80
l2M + 60
M16
18
15
12
b + 18
b + 100
25
20
b + 18
b + 100
110
l2M + 80
M20
22
20
15
b + 22
b + 130
30
25
b + 22
b + 130
120
l2M + 90
25
Steelwork Fixings
Type BR / Type RC
Flat Top
Type BR
Nose
Clamping
Area K
Tail
Skirt
Z
T
V
X
Y
Versatile clamp for steel beams or rails. The skirt prevents the clamp
rotating during installation. The BR tail spans slotted holes.
Suitable for flanges up to 8°.
Product
Code
Bolt 8.8
Z
BR12
12
Safe Working Loads
Tensile / 1 Bolt
kN
kN
5.8
0.7
Torque
Nm
69
Y
mm
26
Dimensions
Tail Length V
short medium
mm
mm
4
6
X
mm
13
T
mm
13
Width
mm
29
BR16
16
7.3
1.5
147
30
16
6
8
16
35
BR20
20
14.7
3
285
36
19
7
10
19
42
BR24
24
19.7
4.5
491
48
25
9
12
25
54
Order example: BR12 short HDG
Type RC
Hole to suit
M12-M24
Nose
Forged steel, corrosion protection as required
Skirt
Tail
Special clamp to secure rails
or steel beams of 10mm or
greater. Packings are available
for thicker flanges. The RC tail
spans slotted holes.
Suitable for flanges up to 5°.
The product will be drilled to
suit hole size and position
requirements of the
applications.
W
L
H
V
X
Product
Code
Bolt 8.8
Z
RCS12
M12
Min. Safe Working Load1)
Tensile / 1 Bolt
kN
2.6
RCS16
M16
4.0
147
RCS20
M20
9.6
285
RCS24
M24
12.3
491
X
mm
6.5 - 26.5
Dimensions
L
mm
76
H
mm
29
Width W
mm
50
10
9 - 24
76
29
50
10
11 - 22
76
29
50
10
13 - 20
76
29
50
Torque
Nm
69
Tail Length V
mm
10
1) The safe working load depends on the position of the bolt hole. The greater dimension X the lower the load.
Order example: RCS12 HDG with dimension X = ______ mm
26
1
Steelwork Fixings
Accessories / Plate and Packing Details for Type BR
1
Type CW - Clipped Washer
hot dip galvanised
T
Y
X
Z
Product
Code
Bolt
Z
CW12
M12
Y
mm
6
Dimensions
X
T
mm
mm
19.5
2.5
CW16
M16
8
17.5
3
38
CW20
M20
10
22
4
44
CW24
M24
12
29
4
57
Width
mm
31
Order example: CW12 BZP
Type P1 short / P2 short
Mild Steel, malleable iron,
TP1
Y
TP2
X
Z
Product
Code
P1
P2
P1S12 P2S12
Bolt
Z
M12
Y
mm
6
X
mm
16
Dimensions
TP1 TP2
mm mm
6
12
Width
mm
30
P1S16
P2S16
M16
8
21
8
16
35
P1S20
P2S20
M20
10
23
10
20
43
P1S24
P2S24
M24
12
32
12
24
54
Order example: P1S12 BZP
For Type BR please see the following:
• Location and End Plates, page 15
• Calculation of bolt length, page 11
• For beams with slopes of up to 8º please use the table for beams of up to 5º slope (see page 15).
NB: The flange thickness refers to t1.
Type BR is only available with tail length ‘short’ and ‘medium’.
b
h
t1
27
Steelwork Fixings
Type Lindapter-HD
1
Type Lindapter-HD
Lindapter-HD
Malleable iron, SG iron, corrosion protection as requested
Plug
Nose
Leg
Skirt
Lindapter-HD Spring Clip
Elastomer Spring
The rail clamps Type Lindapter HD and Lindapter HD Spring facilitate
precise alignment of the rails by allowing a high degree of stepless lateral
adjustability.
Technical Data
Suitable for all rails with tapered flanges and crane speeds of up to
60m/min. For wheel loads above 400kN or lateral loads higher than
wheel loads please contact Lindapter.
Product
Code
Clip
Type
HD20 H
Hard
M20
46
HD20 S
Soft
M20
46
HD20 SP
Spring
M20
46
HD20 S-P
Soft & Pad
M20
HD20 SP-P Spring & Pad
HD24 H
Hard
Bolt 8.8
Z
Lateral Safe Working Load
(4:1 Factor of Safety) Torque
kN
Nm
Dimensions
Lateral Adjustm. Plate Width
max L
min A
mm
mm
Leg
V
mm
Stud
Length H
mm
Distances
X2)
Y2)
mm
mm
Width
W
mm
450
F-8
F + 38
± 11.5
B + 137
30
27
450
F-5
F + 40
± 11.5
B + 137
30
27
74
450
F-7
F + 40
± 11.5
B + 137
30
27
74
46
450
F1)
F + 45
± 11.5
B + 137
30
27
74
M20
46
450
F - 21)
F + 45
± 11.5
B + 137
30
27
74
M24
60
760
F-8
F + 41
±8
B + 130
30
27
74
74
HD24 S
Soft
M24
60
760
F-4
F + 43
±8
B + 130
30
27
74
HD24 SP
Spring
M24
60
760
F-7
F + 43
±8
B + 130
30
27
74
HD24 S-P
Soft & Pad
M24
60
760
F + 11)
F + 48
±8
B + 130
30
27
74
M24
60
760
F - 21)
F + 48
±8
B + 130
30
27
74
HD24 SP-P Spring & Pad
1) Based on 5mm thick resilient pad.
2) Based on plug set at 3 o’clock position.
NB: Leg length V for use with rail sections only with tapered base. For parallel sections please refer to Lindapter.
Order example: HD20 H HDG for rail: ________
28
1
Steelwork Fixings
Type Lindapter-HD
Lindapter-HD
Lindapter-HD: Variation Hard Clip
Leg length V should be selected to clamp rail down tightly and allow no
vertical rail movement. Not to be used when the rail is supported by a
resilient pad.
H
F
Y
Lindapter-HD: Variation Soft Clip
Leg length V should be selected to allow vertical rail movement caused
by rail wave, whilst holding the rail in precise alignment laterally. Rail
ends need to be fixed.
X
V
B
A
H
F
Y
X
V
B
A
Lindapter-HD Spring Clip
The spring clip version incorporates an elastomer spring into the nose
of the product, designed to provide some vertical restraint to the rail
whilst still allowing the rail to lift with rail wave.
The elastomer spring is manufactured from high density synthetic
polymer which has a Shore A hardness of 94.97. The spring is
unaffected by salt water and most chemicals and has a high resistance
to abrasion.
H
F
Y
X
V
B
A
Resilient Pad
Both the spring and soft clips can be used with a resilient pad to
decrease track running noise /structural vibration, level out irregular
contact between surface and rail and to spread wheel load evenly over
a wider area.
V
Resilient Pad
Installation
1. Position clip on bolt or stud. Place
the plug in 3 o’clock position and
tighten the nut.
2. Rotate the built in nut profile in a
clockwise direction from the 3
o’clock position to locate the clip
against the rail and laterally adjust
the rail if required.
+L
-L
W
3. Apply the recommended torque to
the hexagon nut.
29
Steelwork Fixings
Type BSNT / Type BSLN
Flat Top
Nose
Type BSNT
Z
T
Y
X
Special clamp for installation of beams flange to flange. The location
plate is substituted by a connecting frame made of steel flats equalling
the flange thicknesses in height. The clamps are welded to this frame.
Safe Working Loads
Tensile / 1 Bolt
kN
5.8
Torque
Nm
69
Y
mm
26
X
mm
13
T
mm
16
Width
mm
29
M16
7.3
147
30
16
20
35
M20
14.7
285
36
19
24
42
M24
19.7
491
48
25
32
54
Product
Code
Bolt 8.8
Z
BSNT12
M12
BSNT16
BSNT20
BSNT24
Dimensions
Order example: BSNT12 HDG
Type BSLN
Extended Nose
Flat Top
Tail
Skirt
Z
T
V
K
Y
X
Special clamp designed with longer nose to extend the contact area
with the steel section. For parallel flanges only. Can be used with types
CW, P1 short, P2 short.
M12
Safe Working Load
Tensile / 1 Bolt
kN
5.8
Torque
Nm
69
Y
mm
45.5
X
mm
15.5
M16
7.3
147
44
17
Product
Code
Bolt 8.8
Z
BSLN12
BSLN16
Dimensions
Tail Length
V
mm
6
11
T
mm
17
Width
mm
28
16
32
Order example: BSLN12 HDG
30
1
Steelwork Fixings
Type F9 / Type HW/HC
1
Type F9
Nut
Bolt
Z
Single Leg
V
Jaws
W
T
X
V
Double Leg
Flange Clamp for connecting all types of parallel running steelwork with
flanges of the same width. Can be used with bolts or alternatively with
threaded rod.
Not suitable for tapered flanges.
Product Code
with
without
Bolt
Bolt
F910NC
F910NB
M10
Safe Working Loads
Tensile / 1 Bolt
kN
2
F912NC
F912NB
M12
2.8
39
26 - 60
35
17
24
30
F916NC
F916NB
M16
5.6
93
29 - 69
43
21
28
35
Bolt 4.6
Z
Torque
Nm
20
Clamping Range
W
mm
19 - 42
X
mm
25
Dimensions
V
T
mm
mm
13
19
Width
mm
24
F920NC
F920NB
M20
8.4
177
32 - 82
51
25
35
44
F924NC
F924NB
M24
14.0
235
45 - 95
76
38
55
63
Order example: F910NC HDG
Type HW/HC
hot dip galvanised
X
Z
Hemispherical Washer
R
W1 L
W2
Y
10°
Hemispherical Cup
For vertical suspension on angled surface of up to 10° swing either side of
the vertical. The hemispherical washer (HW) can be used without the cup.
Loads are subject to applications, please contact Lindapter.
Product Code
Hemispherical Cup
mm
X
W1
mm
mm
Hemispherical Cup
Y
W2
mm
mm
Dimensions
Hemispherical Washer & Cup
R
L
mm
HW06
-
19
9
-
-
-
HW08
-
22
10
-
-
-
-
HW10
HC10
25
12
32
12
13
14
HW12
HC12
29
12
35
12
14
16
HW16
HC16
34
16
41
16
17
19
HW20
HC20
44
19
54
19
22
24
HW24
HC24
57
25
67
25
29
32
Order example: HC10 BZP
31
Type SC / Type LP
Steelwork Fixings
Type SC / Type LP
Corrosion Protection as required
Bespoke units for multiple applications with vertical load, loads at an angle and rotation of up to 360°. Shown are typical applications, other loads and
designs available. All loads subject to suitability of supporting section.
Type SC
Type SC
Shackle Clamp with 4 Bolts
Loading:
up to 60.0kN
Directions: vertical lift
Angle:
± 10º
Type LP4
Type LP4
Lifting Point with 4 Bolts
Loading:
up to 7t (68kN)
Directions: 360º rotation
Angle:
0 - 90º
Type LP6
Type LP6
Lifting Point with 6 Bolts
Loading:
up to 10t (98kN)
Directions: 360º rotation
Angle:
0 - 90º
Order details: Loading, rotation, angle and beam dimensions
32
1
Steelwork Fixings
Type FC
1
Type FC
Forged steel, bright zinc plated plus JS500
The Flush Clamp is a Girder Clamp System without the need of a
location plate. Suitable for connecting beams of varying widths and
thicknesses. Suitable for flanges up to 10° slope.
Product
Code
Special
Bolt
8.8
FC16
M16
Safe Working Loads
Tensile / 4 Bolts
kN
kN
30.0
7.5
Torque
Nm
147
Clamping Range V
Flange Thickness Flange Width1)
mm
mm
5 - 19
75 - 180
Dimensions
T
B
mm
mm
22 - 27
304
1) Depending on beam connection angles (see table below).
Order example: FC16
Half nut
Nut
Flat washer
Special washer
Body
min V
max T
max V
min T
B
Special Bolt
Minimum Possible Beam Connection Angles
Bottom Beam
Top Beam
Flange
Width
76.2
mm
101.6
mm
127.0
mm
152.4
mm
177.8
mm
76.2 mm
101.6 mm
45°
50°
50°
50°
55°
55°
65°
65°
75°
75°
127.0 mm
152.4 mm
55°
65°
55°
65°
55°
65°
65°
65°
75°
75°
177.8 mm
75°
75°
75°
75°
80°
Angle
33
Steelwork Fixings
Loads and Specifications
Loads and Specifications
Reference is made throughout this catalogue to loads related to our product applications. Given loads are for boltgrade 8.8 unless otherwise stated.
These are defined below. Should you have any difficulty in selecting the correct product for your needs, please contact us.
Tensile Loading
Combined Loads
In tensile applications the load
transmits a force parallel to the
centre line of the bolt shank,
hence applying a load to the
contact point of the Lindapter.
See product data tables for
allowable tensile loads at varying
bolt sizes.
Frictional Loading
When the fixings are subject to
more than one load condition,
the resulting forces must be
calculated to determine the
product and bolt sizes required.
Please contact Lindapter with
your application.
Compression Loading
The force is applied at 90° to
the bolt shank. The point at
which slip occurs depends
upon the condition and finish
of the steelwork, the coating
of the Lindapter and the
grade of bolt used. Slip is
defined as the constant load
at which relative movement
between clamped
components exceeds
0.1mm.
Shear Loading
Torque
The Safe Working Load of the
assembly is determined by the
bolt grade and diameter as the
force is resisted by the cross
sectional area of the bolt
shanks. It is recommended that
reference be made to the bolt
manufacturers’ technical
literature or the relevant
structural steel design code to
ascertain a Safe Working Load
per bolt.
34
Force here is applied direct to
the supporting section rather
than the Lindapter products.
If, however, there is a gap
between the surfaces being
connected, the buckling
strength of the supporting
fabrication must be considered.
The recommended torque
values stated in the product
sections must be applied in
order to achieve the stated Safe
Working Loads. Any reduction in
torques applied will lower the
product Safe Working Load and
is not recommended.
1
1
Steelwork Fixings
Technical Enquiry Fax
Technical Enquiry Fax
Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Department . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Town . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Post Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E-mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Web
www . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Your details will only be used internally and not disclosed to third parties.
Project Name / Reference:
...............................................................................................................
...............................................................................................................
1. Is your case comparable with an application in this catalogue?
If yes, please state page and number . . . . . . . . . . . . . . . . . . . . . . .
❍
If no, please enclose drawing detail
2. Load per connection:
Tensile . . . . . . . . . . . . . . . kN
Frictional . . . . . . . . . . . . . kN
Please state any special load conditions (vibration, etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Static Load
❍
Dynamic Load
❍
3.
Load Cycles . . . . . . . . . . . . . . .
Beam Type
Flange Width
Flange Thickness
Top Beam
Bottom Beam
4. Corrosion protection of beams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. Number of connections required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fax:
Email:
+44 (0) 1274 521130
[email protected]
35
Steelwork Fixings
36
1
2
3
4
5
6
7
8
9
1
Steelwork Fixings
10
11
12
13
14
15
5
16
17
18
1
37
Steelwork Fixings
38
19
20
21
22
23
24
25
26
27
1
Steelwork Fixings
28
29
30
31
32
33
34
35
36
1
39
Cavity Fixings
Cavity Fixings
In the late 1940’s Lindapter revolutionised the
concept of ‘blind’ fixing, or where limited access is
available, with the development of the Lindibolt.
Some time later, following the introduction and
wide acceptance of hollow section steelwork, the
range was expanded to include the Hollo-Bolt®.
Due to the continued development and expansion
of SHS into the wide variety which is available
today from square, rectangular, circular to oval this
product group has also seen a rapid expansion in
diameters, lengths, finishes, and head types finally
culminating in the Design Councils Millennium
Products Award for Innovation which the
Hollo-Bolt® attained in 2000.
Following comprehensive testing the Hollo-Bolt® is
now included in the BCSA/SCI publication ‘Joints
in Steel Construction – Simple Connections’, more
commonly known simply as the Green Book, as
well as being approved by the Deutsches Institut
für Bautechnik.
The Hollo-Bolt® is ideal for use on any steel
structure eliminating the need for unsightly welding
or strapping, installation is simple and quick
requiring only the type of hand tools commonly
available on site.
Typical Hollo-Bolt® applications include:
• Primary Steelwork
• Secondary Steelwork
• Bridges
• Cladding
• Balconies
• Towers and masts
• Staircases and handrails
40
2
Cavity Fixings
Type HB - Hollo-Bolt®
2
Steel, bright zinc plated plus JS 500
Steel, hot dip galvanised
Stainless Steel Grade 316
Collar
Rubber Washer
Sleeve
Cone
Suitable for hollow sections, tubes and where access is available from
one side only. For high corrosion protection the Hollo-Bolt® comes with
additional JS500 protection as standard or hot dip galvanised.
Sizes M16 and M20 have a patented collapse mechanism for
optimised clamping force. Speedy installation with standard tools and
for the Type Hollo-Bolt® Flush Fit with installation nut. (One free per box)
Awarded the Design Council’s Millennium Product status for
innovation in the year 2000.
Hollo-Bolt®: M8, M10, M12
Hollo-Bolt®: M16, M20
H
H
L
L
D
d
D
d
Rubber Washer
W
W
Rubber Washer compressed /
increased clamping force
*8
Head Variations
Flush Fit
Countersunk
(Head)
Hexagonal Head
Socket Head
Cap Screw
Button Head Security
M8-M12
M8-M16
M8-M20
Supplied to order
Supplied to order
41
Cavity Fixings
Load Tables for Types HB and HBFF
Product
Code
Bolt
Clamping
Thickness
Outer
Ply1)
Sleeve
Collar
Length
Outer Ø
d
mm
Height Ø
Torque
min t
mm
-
L
mm
30
49
68
HB08-1
HB08-2
HB08-3
M8x50
M8x70
M8x90
HB10-1
HB10-2
HB10-3
M10x55
M10x75
M10x90
3 - 22
22 - 41
41 - 60
-
HB12-1
HB12-2
HB12-3
M12x60
M12x90
M12x110
3 - 25
25 - 47
47 - 69
HB16-1
HB16-2
HB16-3
M16x75
M16x100
M16x120
HB20-1
HB20-2
HB20-3
M20x90
M20x120
M20x150
Dimensions
mm
140x140x5.0
150x150x6.3
200x200x10.0
100x100x6.3
140x140x5.0
140x140x8.0
150x150x6.3
180x180x8.0
200x200x10.0
140x140x5.0
140x140x8.0
150x150x6.3
180x180x8.0
200x200x10.0
100x100x6.3
100x100x10.0
140x140x5.0
140x140x6.3
140x140x8.0
140x140x12.5
150x150x6.3
180x180x8.0
200x200x10.0
140x140x6.3
140x140x8.0
140x140x10.0
140x140x12.5
150x150x6.3
180x180x8.0
200x200x10.0
kN
4.0
4.0
4.0
7.0
6.0
8.5
8.0
7.0
8.0
6.5
10.5
10.0
10.0
10.5
13.5
18.5
8.0
15.0
20.0
21.0
11.5
17.0
15.0
16.0
23.0
25.0
35.0
12.5
18.0
19.0
A/F
Material
W
mm
3 - 22
22 - 41
41 - 60
Safe Working Loads2)
Tensile
Single
Shear
SHS Section
H D
mm mm
mm
Nm
13.75
5
22
19
23
S275
30
48
67
17.75
6
29
24
45
S275
-
35
57
79
19.75
7
32
30
80
S275
12 - 29
29 - 50
50 - 71
8
8
8
41.5
63
84
25.75
8
38
36
190
S275
12 - 34
34 - 60
60 - 86
8
8
8
50
76
102
32.75
10 51
46
300
S275
kN
5.0
10.0
15.0
30.0
40.0
Type HBFF - Hollo-Bolt® Flush Fit
Product
Code
Counter
Sunk
Bolt
mm
Clamping
Thickness
Outer
Ply
Sleeve
Length
Outer Ø
d
mm
W
mm
min t
mm
L
mm
Collar
Installation Torque
Tool
Height Ø
A/F
H D
mm mm
mm
Nm
SHS Section
Material
HBFF08-1
M8x50
5
10 - 27
8
30
13.75
5
24
19
23
S275
HBFF10-1
M10x60
6
12 - 27
10
30
17.75
6
30
24
45
S275
HBFF12-1
M12x60
8
12 - 30
10
35
19.75
7
33
30
80
S275
Dimensions
mm
140x140x5.0
150x150x6.3
180x180x8.0
200x200x10.0
100x100x6.3
140x140x5.0
140x140x8.0
150x150x6.3
180x180x8.0
200x200x10.0
140x140x5.0
140x140x8.0
150x150x6.3
180x180x8.0
200x200x10.0
Safe Working Loads
Tensile
Single
Shear
kN
4.0
4.0
4.0
4.0
7.0
6.0
8.5
8.0
7.0
8.0
6.5
10.5
10.0
10.0
10.5
kN
5.0
10.0
15.0
Order example: HB08-1 BZP plus JS 500
HBFF08-1 BZP plus JS 500 without / with ____ installation nut(s)
1) The thickness of the outer ply needs to be at least 8mm. If necessary spacer washers should be used beneath the collar to
increase the thickness to 8mm.
2) The Hollo-Bolt® can be used on a wide variety of SHS sections; those shown above are only representative to give an
indication of variations in Hollo-Bolt® capacity.
The safe working loads, in both tension and shear, are applicable to the Hollo-Bolt® only, failure of the section, particularly
on those with thin walls and a wide chord face, could occur at a lower figure and its strength should be checked using the
‘Green Book’ design guide.
42
2
2
Cavity Fixings
Technical Data for Types HB and HBFF
Joints in Steel Construction - Simple Connections
The tables on the opposite page state the SWL with a 5:1 factor of safety and
should be used for secondary applications, for primary design please consult
the guide Joints in Steel Construction - Simple Connections.
The guide provides design guidance for the use of Hollo-Bolt® and gives essential
information for structural steelwork connections for use in buildings designed by the
‘Simple Method’ i.e. braced frames where connections carry mainly shear and axial loads
only.
To obtain further details on the Simple Connections guide please contact:
The Steel Construction Institute
Tel: +44 (0) 1344 636 525
Fax: +44 (0) 1344 636 570
www.steel-sci.org
Published by
SCI/BCSA Connections Group.
Publication Number: P212
ISBN 1 85942 072 9
Bolt Diameter, Hole and Edge Distances Type HB
Clearance
Type
Hole Ø
Hole Distances
Edge Distances
d1
min A
min B
mm
mm
mm
mm
HB08
14 (+1.0 / -0.2)
35
13
B + C > 17.5
HB10
18 (+1.0 / -0.2)
40
15
B + C > 22.5
HB12
20 (+1.0 / -0.2)
50
18
B + C > 25.0
HB16
26 (+2.0 / -0.2)
55
20
B + C > 32.5
HB20
33 (+2.0 / -0.2)
70
25
B + C > 33.0
min t
B+C
d1
d1
A
Installation Hollo-Bolt®
B
C
1. Align pre-drilled fixture and
steelwork. Insert Hollo-Bolt®
through fixture and steelwork.
2. Grip the Hollo-Bolt® collar with
an open ended spanner.
3. Using a torque wrench,
tighten the central bolt to the
recommended torque.
Bolt Diameter, Hole and Edge Distances Type HBFF
Clearance
Type
HBFF08
Hole Ø
Countersunk
Ø
Depth
Hole Distances
Edge Distances
d1
d2
t1
min A
min B
mm
mm
mm
mm
mm
mm
14 (+1.0 / -0.2)
27
6.5
35
13
B + C > 17.5
90º
d2
min t t1
B+C
HBFF10
18 (+1.0 / -0.2)
31
6.5
40
15
B + C > 22.5
HBFF12
20 (+1.0 / -0.2)
35
7.5
50
18
B + C > 25.0
d1
d1
A
B
C
Installation Hollo-Bolt® Flush Fit
Installation nut
1. Align pre-drilled fixture and
steelwork. Insert Hollo-Bolt®
through fixture and steelwork.
2. Apply installation nut and grip nut
with an open ended spanner.
3. Using a torque wrench, tighten the
central counter-sunk bolt to the
recommended torque.
43
Cavity Fixings
Type LB2 - Lindibolt 2®
Washer
Type LB2 - Lindibolt 2®
Steel, Stainless Steel Grade 316, bright zinc plated
Main Body
Setscrew
Cone
Locknut
Nut
D
W
C
B
F
A
d
Z
P
Y
W
Self heading bolt suitable for fixing to hollow-sections, tubes and where
access is available from one side only. The Lindibolt® uses a standard
clearance hole.
Product
Code
®
Hole
Ø
d
mm
11
Safe Working Load1)
(Factor of Safety 5:1) Clamping Length Projection
Tensile
Single
Shear
W
P
kN
kN
mm
mm
3.0
3.4
7 - 30
7.5 - 10
Torque
Main Body B and Nut C&D
Thread
Z
Torque
A/F
Nm
mm
M10
20
17
Setscrew F
LB10
Lindibolt
Size Length
Z
Y
mm
M10
69
M5
Torque
Nm
6
LB12
M12
80
13
5.0
5.0
10 - 36
9 - 12
M12
31
19
M6
11
10
LB16
M16
105
17
8.0
9.8
12 - 48
12 - 16
M16
81
24
M8
23
13
LB20
M20
128
21
14.0
15.2
14 - 60
15 - 20
M20
129
30
M10
45
17
LB24
M24
158
25
20.0
22.5
18 - 72
18 - 24
M24
203
36
M12
80
19
Bolt
F
A/F
mm
8
1) The safe working loads, in both tension and shear, shown above are applicable to the Lindibolt 2® only.
Failure of the section, particularly on those with thin walls and a wide chord face, could occur at a lower figure and its strength should be checked.
Order example: LB10 BZP
Installation
1. Set nut (C) at (W) plus projection (P).
Tighten Locknut (D).
2. Align pre-drilled fixtures. Insert Lindibolt® through both fixtures,
cone end first.
3. Hold nut (C) with spanner and tighten bolt (F).
Loosen off locknut (D) and tighten nut (C).
Secure by re-tightening locknut (D).
44
2
Cavity Fixings
1
2
3
4
5
6
2
45
Composite Decking Fixings
Lindapter composite decking fixings have all been
designed in conjunction with the various decking
manufacturers to ensure they fulfil the necessary
requirements from ease of installation to carrying
capacity. All the fixings are designed to fit inside
the dovetail shaped re-entrant channel which is
common throughout all the profiles and give a
secure point from which building services can be
suspended with guaranteed capacities.
To guarantee the published capacities it is
important that all the Lindapter Composite Decking
Fixings are installed only when the slab has been
poured and the concrete reaches full strength.
Advantages include:
• Speed of installation
• No special tools required
• No weakening of the decking profiles
• No damage of the surfaces of the decking
• No possibility of delamination
• Adjustable and easily removable
46
3
Type AW
3
Type AW - Alphawedge
Locking Plate: Pre-galvanised strip
Wedge: Malleable iron, bright zinc plated
Wedge
Locking Plate
The Alphawedge is designed for Ribdeck AL, E60 and 80 profiles
manufactured by Richard Lees Steel Decking (see page 52).
Product
Code
Rod
4.6
AW06
M6
Safe Working Load
Tensile / 1 Rod
kN
1.0
Torque
Nm
10
AW08
M8
1.0
10
AW10
M10
1.0
10
Order example: AW06
Installation
1.
2.
3.
4.
1. Pre-assemble the Alphawedge and Locking Plate onto the threaded rod (flat surface uppermost).
2. Insert wedge into the re-entrant channel of the decking, rotate 90°.
3. Slide plate up the threaded rod, over the wedge, to lock it in position into the channel.
4. Tighten the locknut beneath the plate to hold the assembly in position.
47
Type MW2
Type MW2 - Multiwedge 2
Bracket: Pre-galvanised strip
Multinut: Malleable iron, bright zinc plated
Multinut
Bracket
The Multiwedge 2 is designed for MD60 and MD80 profiles
manufactured by Kingspan Structural Products (see page 52).
M6
Safe Working Load
Tensile / 1 Rod
kN
1.47
Torque
Nm
10
M8
1.47
10
M10
1.47
10
Product
Code
Rod
4.6
MW06
MW08
MW10
Order example: MW06
Installation
1.
2.
3.
4.
1. Position Multi-nut and bracket on threaded rod (flat surface uppermost) and insert one leg of bracket into re-entrant channel of decking.
Snap other leg of bracket into channel.
2. Slide assembly to desired position along length of re-entrant channel.
3. Push and turn the multi-nut clockwise until it locks into the channel walls.
4. Tighten the hexagon nut beneath the assembly.
48
3
Type TR60 / Type VN
3
Type TR60
Locking Plate: Pre-galvanised strip
Wedge: Malleable iron, bright zinc plated
Wedge
Locking Plate
The TR60 is designed for TR60 and 80 profiles manufactured by
Structural Metal Decks (see page 52).
M6
Safe Working Load
Tensile / 1 Rod
kN
1.0
Torque
Nm
10
M8
1.0
10
M10
1.0
10
Product
Code
Rod
4.6
TR6006
TR6008
TR6010
Order example: TR6006
Installation
1.
2.
3.
4.
1. Pre-assemble the wedge and locking plate onto the threaded
rod (flat surface uppermost).
2. Insert wedge into the re-entrant channel of the decking and
rotate until the chamfered cams engage on the sides of the
channel.
3. Slide the plate up the threaded rod and over the wedge to lock
it into position in the channel.
4. Tighten the locknut beneath the plate to hold the assembly in
position.
Type VN - V-Nut
Installation
Malleable iron, mild steel, bright zinc plated
12.5mm
1.
2.
3.
25mm
13mm
The V-Nut fits the re-entrant channel of several composite floor
deckings (see page 52).
1. Screw VN onto threaded rod.
M6
Safe Working Load
Tensile / 1 Rod
kN
1.8
VN08
M8
2.0
10
VN10
M10
2.1
10
Product
Code
Rod
4.6
VN06
2. Insert VN and rod into re-entrant channel of decking.
Torque
Nm
10
3. Rotate both rod and VN through 90° so that tapered sides
engage the sides of the channel.
Order example: VN06
49
Type SD2
3
Type SD2 - Slimdek 2
Inner Body
V-Nut
Pre-galvanised strip
Main Body
Cam
The Slimdek 2 is designed for the CF225 profile manufactured by
Corus Panels and Profiles. It gives a fully flexible suspension position
(see page 52).
M6
Safe Working Load
Tensile / 1 Rod
kN
1.0
SD208
M8
1.0
12
SD210
M10
1.0
12
Product
Code
Rod
4.6
SD206
Torque
Nm
12
Order example: SD206
Installation
1.
2.
3.
4.
5.
6.
1. With Slimdek 2 in it’s retracted position (as supplied) locate the fixing in the re-entrant channel.
2. Hold Slimdek 2 in position with one hand, then rotate cam into the direction shown above with a spanner.
3. Rotate the nut until the inner body of the fixing locates against the re-entrant channel, and the nut feels tight.
4. Offer the V-Nut on a threaded rod up to the main body.
5. Rotate V-Nut through 90° to allow it to sit at the bottom of the Slimdek 2 body.
6. Secure the assembly with a nut.
50
Type TC
3
Type TC - Toggle Clamp
Steel Strip, bright zinc plated
Nut
Toggle
V
The Toggle Clamp is designed for service suspension from pre-cast
hollow core slabs (minimum depth of core 75mm) as well as SHS,
steel sheeting or purlins.
T
W
Product
Code
Rod
min. 8.8
TC08
M8
Hole
Ø
mm
22
TC10
M10
25
Safe Working Load
Tensile / 1 Rod
kN
2.45
Torque
Nm
10
T
mm
68
Dimensions
W
mm
16.5
Width V
mm
13
2.45
10
68
17.5
15
Order example: TC08
Installation
LIN
DA
PT
ER
2.
3.
LINDAPTER
LINDAPTER
1.
ER
LINDAPTER
LINDAPT
4.
5.
6.
1. Drill hole. If toggle is to be used to support from pre-cast hollow core slab, ensure hole is central to hollow core.
2. Insert threaded rod through toggle, ensuring nut is flush with end of rod.
3. Align toggle parallel with rod, so that nut engages into the retaining cavity.
4. Offer up the assembly, inserting the toggle body completely through the hole.
5. Shake rod so that toggle body locates horizontally across hole.
Allow rod to drop down so that the nut locates in the seat in the toggle body.
6. Wind up rod to top of section as shown as high as possible. Secure the assembly with a nut and washer.
51
Decking Fixings Guide
Deckings
Richard Lees Steel Decking
Lindapter Decking Fixings
Type AW
• Ribdeck AL
• Ribdeck E60
• Ribdeck 80
Kingspan Structural Products
Type MW2
• MD60
• MD80
Structural Metal Decks
Type TR60
• TR60
• TR80
Corus Panels & Profiles
Type SD2
• CF225
Structural Metal Decks
Type VN
• R51
Corus Panel & Profiles
• CF51
Richard Lees Steel Decking
• Holorib
Kingspan Structural Products
• MD50
52
3
Installation
3
Installation
Type AW - Alphawedge
1. Pre-assemble the Alphawedge and locking plate onto the threaded
rod (flat surface uppermost).
2. Insert wedge into the re-entrant channel of the decking, rotate 90°.
3. Slide plate up the threaded rod, over the wedge, to lock it in position
into the channel.
1.
2.
3.
4. Tighten the locknut beneath the plate to hold the assembly
in position.
4.
Type MW2 - Multiwedge 2
1. Position Multi-nut and bracket on threaded rod (flat surface
uppermost) and insert one leg of bracket into re-entrant
channel of decking.
Snap other leg of bracket into channel.
1.
2.
3.
4.
2. Slide assembly to desired position along length of
re-entrant channel.
3. Push and turn the multi-nut clockwise until it locks
into the channel walls.
4. Tighten the hexagon nut beneath the assembly.
Type TR60
1. Pre-assemble the wedge and locking plate onto the threaded rod
(flat surface uppermost).
2. Insert wedge into the re-entrant channel of the decking and rotate
until the chamfered cams engage on the sides of the channel.
3. Slide the plate up the threaded rod and over the wedge to lock it
into position in the channel.
1.
2.
3.
4.
4. Tighten the locknut beneath the plate to hold the assembly in
position.
Type SD2 - Slimdek 2
1.
2.
3.
1. With Slimdek 2 in it’s retracted position (as supplied) locate the fixing
in the re-entrant channel.
2. Hold Slimdek 2 in position with one hand, then rotate cam into the
direction shown above with a spanner.
3. Rotate the nut until the inner body of the fixing locates against the
re-entrant channel, and the nut feels tight.
4.
5.
6.
4. Offer the V-Nut on a threaded rod up to the main body.
5. Rotate V-Nut through 90° to allow it to sit at the bottom of the SD 2 body.
6. Secure the assembly with a nut.
Type VN - V-Nut
1.
2.
3.
1. Screw VN onto threaded rod.
2. Insert VN and rod into re-entrant channel of decking.
3. Rotate both rod and VN through 90° so that tapered sides
engage the sides of the channel.
53
Support Fixings
Support Fixings
Lindapter’s support fixing range offers a series of ideal solutions for all
building services. This includes the suspension of HVAC equipment,
pipe work, fire protection/sprinkler systems, suspended ceilings and all
manner of electrical equipment such as cable tray and ladder. These
products have all been designed to give speed and ease of installation
to reduce time and keep costs under control.
Where necessary support products have been tested, and approved,
by the relevant bodies such as those which oversee and insure fire
protection installations.
For the installation of heavy duty service equipment such as pipe
supports used in the petro chemical industry the steelwork fixings in
section 1 of this catalogue are more suitable.
54
4
4
Support Fixings
Type FLS
Type FLS
High Grade Alloy Steel, bright zinc plated
Setscrew Z
Locknut
Swivel Unit
Nut Basket
T
W
U
X
R
360º
Beam flange clamp with swivel unit. For parallel and sloping flanges.
Supplied with grade 8.8 setscrew for secure grip.
Y
Product
Code
Thread
Y
FLS08
M8
FLS10
M10
Safe Working Load (4:1 Factor of Safety)
Tensile/) 25º Tensile/> 25º to ) 45° Clamping Thickness Setscrew
W
Z
kN
kN
mm
2.5
1.5
3 - 17
M10
2.5
1.5
3 - 17
M10
Torque
Setscrew
Nut
Z
N
Nm
Nm
18
18
18
18
R
mm
55
T
mm
53
55
53
Dimensions
U
X
mm
mm
58
27
58
27
) 25°
) 25°
Width
mm
28
28
Order example: FLS08
Approved Applications
Installation
Z
N
M
S
1.
2.
3.
4.
) 25°
1. Locate FLS onto flange.
General Applications
Parallel Flanges only
2. Ensuring lug on locknut locates into main body, tighten down
setscrew (Z), and then tighten upper locknut (N).
3. Install threaded rod by screwing into nut located in nut basket (S).
Ensure full thread capture.
90°
4. Secure assembly in nut basket (S) from beneath using a locknut
(not supplied).
Ensure that the cup point setscrew always grips on the
tapered side of the flange.
) 45°
) 45°
55
Support Fixings
Type FL
4
Type FL
Malleable iron,
bright zinc plated
Hexagon Setscrew
Square Head Setscrew
Locknut
Rear Hole
(Tapped / Clear)
Main Body
Z
N
T
V
U
W
X
Y
Beam Clamp suitable for use with parallel or tapered flange beams, supplied
with the back hole drilled or tapped. The type FL uses a grade 8.8 cup point
setscrew for secure grip. Supplied with square or alternatively hexagon head
setscrews.
Can be used with type SW – Swivel Unit (see page 57) when connecting to
inclined sections.
Product Code
Clear
Tapped
Safe Working Load
(4:1 Factor
Clamping
Thread
of Safety)
Thickness
Y
Tensile
W
kN
mm
M6
1.1
3 - 17
Setscrew
Z
Torque
SetLockscrew
nut
Z
N
Nm
Nm
8
11
FL106D
FL106T
Hole Ø
Y
mm
7
FL108D
FL108T
9
M8
1.1
3 - 17
M8
8
11
36
35
20
19
FL210D
FL210T
11
M10
2.4
3 - 19
M10
8
22
45
40
22
22
FL312D
FL312T
13
M12
3.1
3 - 23
M10
8
22
50
46
28
25
FL412D
FL410T
13
M10
3.1
3 - 28
M10
8
22
53
51
27
26
M8
T
mm
36
Dimensions
U
X
mm
mm
35
20
Width V
mm
19
Order example: FL210D with Hex Setscrew
FL210D with Square Head Setscrew and SW10
Installation
1. Slide FL onto beam flange and tighten setscrew to
recommended torque. Guideline: tighten the setscrew finger
tight and then apply a further quarter turn (90°) with spanner.
2. Tighten the locknut (N) to the recommended torque.
On tapered flanges the cup point setscrew has to grip on the
inside of the flange.
56
Support Fixings
Type LC / Type SW - Swivel Unit
4
Type LC
Malleable iron, bright zinc plated
Setscrew
Locknut
Main Body
Z
N
T
V
X U
W
Beam clamp with tapped holes in position X and Y to accept threaded rod or cable clips.
For parallel or tapered flanges. Supplied with grade 8.8 cup point setscrew.
Y
Installation see page 56 – type FL
Product
Code
Thread
X
Y
Safe Working Load
Clamping Thickness
Tensile / in Pos. X Tensile / in Pos. Y
W
Setscrew
Z
Torque
Setscrew
Locknut
Z
N
T
Dimensions
U
Width V
kN
kN
mm
Nm
Nm
mm
mm
mm
LC06
M6
M6
0.18
0.59
3 - 20
M6
4
4
25
36
21
LC08
M8
M8
0.18
0.59
3 - 20
M6
4
4
25
36
21
Order example: LC06
Type SW - Swivel Unit
Type FL
High Grade Alloy Steel, bright zinc plated
Type Z10
U
R
V
Swivel unit for applications on inclined beams. Can be used with type FL or type Z10.
Supplied complete with grade 8.8 M10 x 90 setscrew and nut.
Product
Code
Rod
SW10
M10
Safe Working Load
(4:1 Factor of Safety) Max.
Tensile
Inclination
kN
2.4
18°
Rotation
360°
Torque
Nm
11
Dimensions
With Bolt
U
R
Width V
mm
mm
mm
45
25
35
Order example: SW10
57
Type F3 / Type F3-BICC
Support Fixings
Type F3
Nut
4
Bolt
Malleable iron,
hot dip galvanised
Single Leg
Double Leg
Z
V
W
S
R
T
X
V
A two part flange clamp with large clamping range.The bolt can be
substituted with either drop rod or J bolts.
For parallel flanges only.
Product Code
with
without
Bolt
Bolt
F308NC
F310NC
F308NB
F310NB
M8
M10
Safe Working Load
Tensile
kN
0.9
1.2
F312NC
F312NB
M12
2.0
0 - 40
39
29
9
12
35
49
F316NC
F316NB
M16
4.0
0 - 55
93
36
12
16
46
60
F320NC
F320NB
M20
6.0
0 - 70
177
44
15
19
55
76
Bolt 4.6
Z
Clamping
Thickness
W
mm
0 - 25
0 - 30
Torque
Nm
6
20
S
mm
19
22
T
mm
6
7
Dimensions
V
X
mm
mm
8
20
10
25
Width R
mm
33
38
Order example: F308NC
Type F3-BICC
Malleable iron, hot dip galvanised
Z
T
V1
Y
S
W
X
V2
Y
A two part flange clamp which fixes claw type cable cleats directly
beneath the flange.
Supplied with grade 4.6 bolt.
Product
Code
Bolt 4.6
Z
F310BICCA
M10
Safe Working Load
Tensile
kN
1.2
Clamping
Thickness
W
mm
0 - 30
Thread
Y
M10
Torque
Nm
20
T
mm
6.5
V1
mm
10
Dimensions
V2
X
mm
mm
16
30
Width S
mm
40
Order example: F310BICCA
58
Support Fixings
Type SH / Type HW/HC
4
Type SH
Hanger Nut
Y
With special nut
A
C
B
With standard nut
The strap hanger carries FM approval for use in fire sprinkler
installations. Supplied with or without a hanger nut.
Product Code
with
without
Nut
Nut
Pipe
Bore
Nuts
Tapped
Dimensions
A
B
C
mm mm mm
22
75
58
Product Code
with
without
Nut
Nut
SH025N
SH025
25
M8 or M10
Hole Ø
Y
mm
11
Pipe
Bore
Nuts
Tapped
SH080N
SH080
80
M8 or M10
Hole Ø
Y
mm
11
Dimensions
A
B
C
mm mm mm
22 159 114
SH032N
SH032
32
M8 or M10
11
22
86
64
SH100N
SH100
100
M8 or M10
11
22
219
161
SH040N
SH040
40
M8 or M10
11
22
99
74
SH125N
SH125
125
M12
13
27
247
177
SH050N
SH050
50
M8 or M10
11
22
116
85
SH150N
SH150
150
M12
13
27
284
200
SH065N
SH065
65
M8 or M10
11
22
135
97
SH200N
SH200
200
M16
18
24
373
261
Order example: SH025N with M10 hanger nut
Type HW/HC
hot dip galvanised
X
Z
R
W1 L
W2
Y
10°
Hemispherical Cup
For vertical suspension on angled surface of up to 10° swing either side of
the vertical. The hemispherical washer (HW) can be used without the cup.
Loads are subject to applications, please contact Lindapter.
Product Code
Hemispherical Cup
mm
X
W1
mm
mm
Hemispherical Cup
Y
W2
mm
mm
Dimensions
Hemispherical Washer & Cup
R
L
mm
HW06
-
19
9
-
-
-
HW08
-
22
10
-
-
-
-
HW10
HC10
25
12
32
12
13
14
HW12
HC12
29
12
35
12
14
16
HW16
HC16
34
16
41
16
17
19
HW20
HC20
44
19
54
19
22
24
HW24
HC24
57
25
67
25
29
32
Order example: HC10 BZP
59
Support Fixings
Type Z10 / Type HCW30
Type Z10
Mild steel - bright zinc plated
A purlin clip to suit a large range of purlin sections. Can be used with
type SW – Swivel Unit (see page 57) for use on inclined purlins.
Purlins
Rod
Z10
Kingspan
Multibeam 2 & 3
M10
Safe Working Load
Tensile
kN
0.2
Z10
Metsec
M10
0.1 - 0.2
8
Z10
Zeta
M10
0.15
8
Product
Code
Installation
Torque
Nm
8
2.
1.
3.
Order example: Z10
Z10 with SW10
Type HCW30
The purlin clip HCW30 is suitable for horizontal purlins. Can be used
with type SW-Swivel Unit (see page 57) for use on inclined purlins.
Installation
Product
Code
HCW30
Purlins
Rod
Kingspan
Multibeam 3
M10
Safe Working Load
Tensile
kN
0.2
Torque
Nm
8
1.
2.
Order example: HCW30
60
4
Support Fixings
Type HCW31 / Type WF
4
Type HCW31
A universal purlin clip suitable for multiple different applications.
Product
Code
Purlin
HCW31
Kingspan Multibeam 3
Safe Working Load
Tensile
kN
0.2
Order example: HCW31
Type WF
Mild Steel, bright zinc plated
The Webfix – WF for a quick installation directly from the web of Zed purlins.
Product
Code
Rod
WF10
M10
Safe Working Load
Max.
Tensile
Purlin Thickness
kN
mm
1.0
4
Hole
Ø
mm
18
Max. Distance X
at Angle of
10º
20º
30º
mm
mm
mm
103
94
74
Order example: WF10
Installation
Squeeze legs of WF
together and push
through hole until it
snaps into place.
1.
Assemble with nut and ensure
full thread capture.
2.
Hole position for angled purlins
X
1.
X
Canted Purlins: As the angle
of backwards cant increases,
the maximum allowable
distance X (hole centre to
bottom edge of purlin) must
decrease.
Inclined Purlin: The WF
adjusts to whatever angle is
required. Hole position is not
a limiting factor on product
installation.
2.
61
Support Fixings
Type HCW34
Type HCW34
A one-piece wrap around purlin
hanger. The HCW34 can be used to
suspend from canted purlins at up
to 15° from the vertical.
H
Purlin
Kingspan Multibeam 3
Purlin Height
Total Height H
mm
mm
145
210
M10
Safe Working Load (3:1 Factor of Safety)
Tensile
kN
0.75
HCW34/175
175
240
M10
0.75
HCW34/205
205
270
M10
0.75
HCW34/235
235
300
M10
0.75
HCW34/265
265
330
M10
0.75
Product Code
HCW34/145
Rod
Order example: HCW34/145
Purlin Profiles
62
Multichannel
Lipped C Section
Swagebeam
Multibeam
Zed Section
SFS C Section
UltraBEAM
Zeta Section
Ultrazed Section
4
Support Fixings
Type F3
1
Type WF
2
Type HCW31
4
Type FLS
3
Type HCW30
Type Z10
Type SH
Type SH
4
63
Floor Fixings
Floor Fixings
When designing the floor fixing range of products for chequer plate
and both square and rectangular open bar grating Lindapter combined
speed with ease of installation. None of the products require any site
drilling and/or welding to be done and can easily be installed from
above the flooring; this means no requirement for scaffold towers,
access platforms or MEWP hire giving easier compliance with the
onerous work at height regulations.
Both the Floorfast® & Grate-Fast® are covered by Lloyds Register Type
Approval in respect of their clamping force and resistance to loosening
in areas subject to shock and vibration. Without a need for the issuing
of hot work permits, they are particularly suited to applications where
safety is of paramount importance such as in offshore and onshore
petrochemical and processing industries although they are equally
ideal for applications in all other industrial environments.
64
5
Floor Fixings
Type FF - Floorfast®
5
Type FF - Floorfast®
Malleable iron, Stainless Steel Grade 316,
Unique stepped
clamping face
Socket
setscrew
90º
D
20
2
t
t1
d
Z
60
A - Nominal Clearance
The product consists of a malleable iron body casting
with a countersunk socket screw; the eccentric stepped
web of the casting allows it to lock under the steelwork
providing full face contact when torque is applied.
For thicker flanges packing pieces will be supplied.
Lloyds’ Register Type Approval covers clamping force
and vibration.
½ Flange Width
13
Ferrule
Position of hole centres:
½ flange width - ½ A + 13mm
Countersunk
Product
Code
Bolt1)
Z
Floorplate
Thickness
t
mm
Flange
Thickness
Countersunk Ø for Bolt
BZP
HDG
D
mm
mm
Hole Ø
d
mm
Countersunk Depth for Bolt
BZP
HDG
t1
mm
Torque
Hexagon
Key
FF08
M8
4.5 - 12
3 - 15
9
17
-
4
-
Nm
mm
11
FF10
M10
5 - 12
3 - 15
11
21
19
5
5
4
22
FF12
M12
6 - 12
3 - 15
13.5
25
23
5.8
6
4.8
22
8
1) In hot dip galvanised (M10 and M12) a slotted countersunk screw is supplied.
Order example: FF12 HDG
Installation
1.
2.
1. Pre-assemble Floorfast® on underside of floorplate
with stepped surface facing inwards.
2. Align castings with straight edge parallel
to the edge of the plate and hand tighten.
3. Lay floorplate into position
4. Using a hexagon key release the countersunk screw
one full turn.
5. Tighten down the countersunk socket screw.
3.
4.
5.
Removal
Using a hexagon key, give the Type FF one full anticlockwise turn to release connection from the flange.
65
Floor Fixings
Type GF - Grate-Fast®
5
Type GF - Grate-Fast®
Body: Malleable iron, mechanical galvanised
Top Hat: Mild Steel, mechanical galvanised
Top Hat Bracket
Socket Head
Cap Screw
Cast Body
T
Z
Grating fixing for rectangular open bar grating with cast main body giving
superior clamping force.
GF10 with wider top-hat bracket for different grating sizes.
GF210 for use with 30mm width floor grating bars only.
GF08 with stainless steel top-hat bracket for GRP grating.
Lloyd’s Register Type Approval covers clamping force and vibration.
GF08 / GF10
GF210
W
D
D
min X
max X
Product
Code
GF08
GF10
GF210
Bolt
Z
Flange
T
mm
3 - 19
3 - 19
3 - 19
M8
M10
M10
Grating Bar
Depth
D
mm
22 - 38
20 - 30
19 - 32
Grating Bar
Width
W
mm
5 - 10
3-7
3 - 6.5
W
Bar
Distance
X
mm
19 - 48
25 - 45
30
X
Body
Width
Torque
Hexagon
Key
mm
16
20
20
Nm
5
11
11
mm
6
8
8
Order example: GF08
Installation
1. Position pre-assembled Grate-Fast® with body
between grating bars and nose pointing towards the
steelwork. The arrows on the top hat bracket should
also be pointing towards supporting steelwork and
bracket itself resting on the bearing bars.
2. Slide Grate-Fast® towards steelwork until nose fits
under the beam flange. Where necessary adjust
body/screw to approximate flange thickness/grating
depth.
1.
66
2.
3.
3. Tighten cap screw; the Grate-Fast® body will
automatically rotate until it locks under the bearing
bar, with the nose under the flange. Continue
tightening to the recommended torque.
Floor Fixings
Type GF3030
5
Type GF3030
Spring Steel, Sheraplex
Grating clamp for instant installation requiring no tools.
For parallel flanges only.
Product
Code
Grating Bar
Depth
mm
Grating
Size
mm
Clamping Force at selected Flanges
Clamping Flange Thickness Clamping Thickness Clamping Force / 1 Clamp
mm
mm
N
GF3030
30
30 x 30
8
38
340
GF3030
30
30 x 30
13
43
530
GF3030
30
30 x 30
18
48
680
Order example: GF3030
Installation
1.
2.
3.
1. Position the fixing with the grating bar located between the two tabs on the upper profile, facing towards the supporting steelwork.
2. Apply a downward force to the fixing, so that the lower leg passes through the grating.
3. Apply a downward force to the top of the fixing. The fixing then snaps in to place. If the lower profile contacts the steelwork web,
the GF3030 will automatically relocate itself.
Removal
Using a screwdriver or lever, raise the back of the GF3030 into position shown in diagram 2.
Place the lever between the steelwork and lower leg of the fixing and prise GF3030 away from steelwork.
Deformed or damaged clamps cannot be re-used.
67
Appendix
Section Details
Advance® UKB
Dimensions: BS4-1:2005
B
D
T
Designation
Serial Size
Mass
kg/m
D
mm
B
mm
T
mm
1016 x 305 x 487
437
393
349
314
272
249
222
914 x 419 x 388
343
914 x 305 x 289
253
224
201
838 x 292 x 226
194
176
762 x 267 x 197
173
147
134
686 x 254 x 170
152
140
125
610 x 305 x 238
179
149
610 x 229 x 140
125
113
101
610 x 178 x 100
92
82
533 x 312 x 273
219
182
151
533 x 210 x 138
122
109
101
92
82
533 x 165 x 85
75
66
486.7
437.0
392.7
349.4
314.3
272.3
248.7
222.0
388.0
343.3
289.1
253.4
224.2
200.9
226.5
193.8
175.9
196.8
173.0
146.9
133.9
170.2
152.4
140.1
125.2
238.1
179.0
149.2
139.9
125.1
113.0
101.2
100.3
92.2
81.8
273.3
218.8
181.5
150.6
138.3
122.0
109.0
101.0
92.1
82.2
84.8
74.7
65.7
1036.3
1026.1
1015.9
1008.1
999.9
990.1
980.1
970.3
921.0
911.8
926.6
918.4
910.4
903.0
850.9
840.7
834.9
769.8
762.2
754.0
750.0
692.9
687.5
683.5
677.9
635.8
620.2
612.4
617.2
612.2
607.6
602.6
607.4
603.0
598.6
577.1
560.3
550.7
542.5
549.1
544.5
539.5
536.7
533.1
528.3
534.9
529.1
524.7
308.5
305.4
303.0
302.0
300.0
300.0
300.0
300.0
420.5
418.5
307.7
305.5
304.1
303.3
293.8
292.4
291.7
268.0
266.7
265.2
264.4
255.8
254.5
253.7
253.0
311.4
307.1
304.8
230.2
229.0
228.2
227.6
179.2
178.8
177.9
320.2
317.4
314.5
312.0
213.9
211.9
210.8
210.0
209.3
208.8
166.5
165.9
165.1
54.1
49.0
43.9
40.0
35.9
31.0
26.0
21.1
36.6
32.0
32.0
27.9
23.9
20.2
26.8
21.7
18.8
25.4
21.6
17.5
15.5
23.7
21.0
19.0
16.2
31.4
23.6
19.7
22.1
19.6
17.3
14.8
17.2
15.0
12.8
37.6
29.2
24.4
20.3
23.6
21.3
18.8
17.4
15.6
13.2
16.5
13.6
11.4
Designation
Serial Size
457 x 191 x 161
133
106
98
89
82
74
67
457 x 152 x 82
74
67
60
52
406 x 178 x 85
74
67
60
54
406 x 140 x 53
46
39
356 x 171 x 67
57
51
45
356 x 127 x 39
33
305 x 165 x 54
46
40
305 x 127 x 48
42
37
305 x 102 x 33
28
25
254 x 146 x 43
37
31
254 x 102 x 28
25
22
203 x 133 x 30
25
203 x 102 x 23
178 x 102 x 19
152 x 89 x 16
127 x 76 x 13
Mass
kg/m
D
mm
B
mm
T
mm
161.4
133.3
105.8
98.3
89.3
82.0
74.3
67.1
82.1
74.2
67.2
59.8
52.3
85.3
74.2
67.1
60.1
54.1
53.3
46.0
39.0
67.1
57.0
51.0
45.0
39.1
33.1
54.0
46.1
40.3
48.1
41.9
37.0
32.8
28.2
24.8
43.0
37.0
31.1
28.3
25.2
22.0
30.0
25.1
23.1
19.0
16.0
13.0
492.0
480.6
469.2
467.2
463.4
460.0
457.0
453.4
465.8
462.0
458.0
454.6
449.8
417.2
412.8
409.4
406.4
402.6
406.6
403.2
398.0
363.4
358.0
355.0
351.4
353.4
349.0
310.4
306.6
303.4
311.0
307.2
304.4
312.7
308.7
305.1
259.6
256.0
251.4
260.4
257.2
254.0
206.8
203.2
203.2
177.8
152.4
127.0
199.4
196.7
194.0
192.8
191.9
191.3
190.4
189.9
155.3
154.4
153.8
152.9
152.4
181.9
179.5
178.8
177.9
177.7
143.3
142.2
141.8
173.2
172.2
171.5
171.1
126.0
125.4
166.9
165.7
165.0
125.3
124.3
123.4
102.4
101.8
101.6
147.3
146.4
146.1
102.2
101.9
101.6
133.9
133.2
101.8
101.2
88.7
76.0
32.0
26.3
20.6
19.6
17.7
16.0
14.5
12.7
18.9
17.0
15.0
13.3
10.9
18.2
16.0
14.3
12.8
10.9
12.9
11.2
8.6
15.7
13.0
11.5
9.7
10.7
8.5
13.7
11.8
10.2
14.0
12.1
10.7
10.8
8.8
7.0
12.7
10.9
8.6
10.0
8.4
6.8
9.6
7.8
9.3
7.9
7.7
7.6
Permission to reproduce extracts from BS4-1:2005 is granted by BSI.
British Standards can be obtained in PDF or hard copy formats from the BSI online shop: www.bsigroup.com/shop
or by contacting BSI Customer Services for hard copies only:
Tel: +44 (0) 20 8996 9001, email: [email protected]
68
6
Appendix
Section Details
6
Advance® UKPFC
Designation
Serial Size
430 x 100 x 64
380 x 100 x 54
300 x 100 x 46
300 x 90 x 41
260 x 90 x 35
260 x 75 x 28
230 x 90 x 32
230 x 75 x 26
200 x 90 x 30
200 x 75 x 23
180 x 90 x 26
180 x 75 x 20
150 x 90 x 24
150 x 75 x 18
125 x 65 x 15
100 x 50 x 10
Mass
kg/m
D
mm
B
mm
T
mm
64.4
54.0
45.5
41.4
34.8
27.6
32.2
25.7
29.7
23.4
26.1
20.3
23.9
17.9
14.8
10.2
430.0
380.0
300.0
300.0
260.0
260.0
230.0
230.0
200.0
200.0
180.0
180.0
150.0
150.0
125.0
100.0
100.0
100.0
100.0
90.0
90.0
75.0
90.0
75.0
90.0
75.0
90.0
75.0
90.0
75.0
65.0
50.0
19.0
17.5
16.5
15.5
14.0
12.0
14.0
12.5
14.0
12.5
12.5
10.5
12.0
10.0
9.5
8.5
Mass
kg/m
D
mm
B
mm
T
mm
633.9
551.0
467.0
393.0
339.9
287.1
235.1
201.9
177.0
152.9
129.0
282.9
240.0
198.1
158.1
136.9
117.9
96.9
167.1
132.0
107.1
88.9
73.1
127.5
133.5
99.6
86.1
71.0
60.0
52.0
46.1
51.2
44.0
37.0
30.0
23.0
474.6
455.6
436.6
419.0
406.4
393.6
381.0
374.6
368.2
362.0
355.6
365.3
352.5
339.9
327.1
320.5
314.5
307.9
289.1
276.3
266.7
260.3
254.1
241.4
235.0
228.6
222.2
215.8
209.6
206.2
203.2
170.2
166.0
161.8
157.6
152.4
424.0
418.5
412.2
407.0
403.0
399.0
394.8
374.7
372.6
370.5
368.6
322.2
318.4
314.5
311.2
309.2
307.4
305.3
265.2
261.3
258.8
256.3
254.6
213.9
212.1
210.3
209.1
206.4
205.8
204.3
203.6
157.4
155.9
154.4
152.9
152.2
77.0
67.5
58.0
49.2
42.9
36.5
30.2
27.0
23.8
20.7
17.5
44.1
37.7
31.4
25.0
21.7
18.7
15.4
31.7
25.3
20.5
17.3
14.2
30.1
26.9
23.7
20.5
17.3
14.2
12.5
11.0
15.7
13.6
11.5
9.4
6.8
B
D
T
Advance® UKC
Designation
Serial Size
356 x 406 x 634
551
467
393
340
287
235
356 x 368 x 202
177
153
129
305 x 305 x 283
240
198
158
137
118
97
254 x 254 x 167
132
107
89
73
203 x 203 x 127
113
100
86
71
60
52
46
152x 152 x 51
44
37
30
23
B
D
T
Use of the Advance® name and range of sections
by kind permission of Corus.
69
Appendix
General Enquiries
6
General Enquiries
Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Department . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Town . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Postcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E-mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Web
www . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Your details will only be used internally and not disclosed to third parties.
Please send us:
❍ Catalogue
❍ CD
❍ CPD Booking Form
❍ The following samples:
...............................................................................................................
...............................................................................................................
...............................................................................................................
Lindapter would like to keep you informed about the latest developments which could be valuable for you.
❍
Yes, I would like to be up-dated on new developments.
❍
I am particularly interested in the following:
...............................................................................................................
...............................................................................................................
❍
Please contact me. I have questions regarding:
...............................................................................................................
...............................................................................................................
...............................................................................................................
Fax:
Email:
70
+44 (0) 1274 521130
[email protected]
Appendix
Projects
Canary Wharf, London
Offshore Rig, North Sea
New Chinese National Theatre, Beijing
Wembley Stadium, London
6
St Pancras Station, London
BMW World, Munich
Viaduc de Millau, France
Tower Bridge, London
71
Lindsay House
Brackenbeck Road
Bradford
West Yorkshire
BD7 2NF
England
www.lindapter.com
LindUKFeb09
T: +44 (0) 1274 521444
F: +44 (0) 1274 521130
E: [email protected]

Lindapter Catalogue 09 UK:-

Transcription

Similar documents

Block Ford 400 “FMX”

Lindapter Fixing

Rivnut Installation Instructions

Bolt Messenger

MotoTec Solar Go-kart Assembly Manual

Coupling Identification. CENTAFLEX A (CF-A

Anschutz 1416 - Rifle Shooter January

Frozen Foods

SSG 3000™

Scott Tailwheel 3200 on PA22/20

Lindapter Catalogue