MagnaStar® C-750 System

P r o d u c t
C a t a l o g
TELEDYNE CONTROLS
A Teledyne Technologies Company
Contents
SmartCabin Office ™
1
Basic MagnaStar ® C-2000 System
3
Basic MagnaStar ® C-750 System
4
Accessories
5,6,7
Model 2 Handsets
8,9
Mach-1 Handsets
10
Cable Assemblies
11
Optional Equipment
12,13
Test Equipment
14
Teledyne Iridium Unit (TIU)
15
HSD-128 ™
16,17
CommSer ver ™
18
AWLU
19
GroundLink ®
20
TeleLink ®
21
SmartCabin Office™ Introduction
Teledyne Controls is offering and supporting a complete voice and data communications package that
meets the demanding needs of airborne executive travelers. Teledyne’s SmartCabin Office ™ provides
fully digital voice and high-speed data communication worldwide. These services are enabled through
the seamless integration of MagnaStar ®, the industry dominant airborne telephone system, providing
travelers with uncompressed data transfer rates at speeds up to 128K bps. Optional hardware provides
data networking and communication capabilities in the aircraft cabin similar to those in your business
or home office.
SmartCabin Office™ Configuration
AMT-50
DUPLEXER
DIGITAL
MAGNASTAR ®
HANDSETS
OPTIONAL
DUAL MAGNASTAR ®
HSD-128™
CABIN DISTRIBUTION BUS
MAGNASTAR ®
ARTU
CDBR
CDBR
ETHERNET
ISDN Jack
ISDN
MAGNASTAR®
ISDN TERMINAL ADAPTER
(MITA)
ANALOG MODEM
COMMSERVER
AWLU
Page 2
Everything you need to get down to business
MagnaStar ® C-2000 is a complete
communication package. The system
includes an Air Radio
Telecommunications Unit (ARTU),
an antenna, a duplexer, and a mounting tray. And, of course, you
customize the system to include the necessary handsets and cradles.
Upon installation, you’ll have instant direct dial capabilities. You’ll
be able to make conference calls, multiple calls, seat-to-seat and
cabin-to-cockpit interphone calls. You’ll be able to receive incoming
calls, and you’ll be able to store frequently called numbers for easy
speed dialing. With 9.6K bps data speeds you will be connecting
faster than any other airborne phone available.
With global coverage and automatic uninterrupted handoffs, you’ll
never be out of touch again. MagnaStar ® , the digital airborne phone
you can rely on.
MagnaStar® is a registered trademark of Raytheon
Page 3
MagnaStar ® C-2000 System
The MagnaStar® C-2000 digital airborne telephone system is a complete airborne communication
package designed specifically for corporate and regional aviation. Lightweight and reliable the C-2000
can be mounted in any pressurized or non-pressurized location on the aircraft. The C-2000 system
can support nine (9) independent handset/fax/data calls from up to 50 handset locations, with up to
two of these calls utilizing the Verizon Telecommunications Network.
MagnaStar® , the full featured cabin communications management system.
The basic single handset C-2000 system consists of the following:
• Air Radio Telecommunications Unit (ARTU)
• Mounting Tray
• Duplexer
• Blade Antenna
• Cabin Distribution Bus Repeater (CDBR)
• Call Alerting Switch (CAS)
• Telephone Handset
There are a number of optional system components, handset styles and colors that allow you to
custom tailor your installation to fit your own specific telecommunication system requirements.
Simplified C-2000 System Diagram
Ant
Digital
SATCOM
Duplexer
ARTU
&
Tray
LAN 1
CDBR-1/3
CAS
Ant
Inter E1 Bus
Duplexer
ARTU
&
Tray
Digital
Handset
LAN 2
Alerter
TIU or
Analog Satcom
or HF Radio
AIU
HSD
SATCOM
MITA
Digital
Handset
CDBR-2
Modem
or
Fax
EPS
CHIP
Basic minimum installation
Optional
Page 4
MagnaStar ® C-750 System
The MagnaStar® C-750 Telecommunications Management Unit (TMU) interfaces with
CEPT-E1 compatible and Analog SATCOM as well as other equipment such as HF Radio.
Lightweight and reliable, the C-750 can be mounted in any pressurized or nonpressurized location on the aircraft.
The basic single handset C-750 system consists of the following:
• Telecommunications Management Unit (TMU)
• Mounting Tray
• Cabin Distribution Bus Repeater (CDBR)
• Call Alerting Switch (CAS)
• Telephone Handset
Simplified C-750 System Diagram
Digital
SATCOM
TMU
&
Tray
Inter E1 Bus
TMU
&
Tray
LAN 1
Digital
Handset
CDBR-1/3
CAS
Alerter
TIU or
Analog Satcom
or HF Radio
AIU
IHSD
SATCOM
MITA
Digital
Handset
CDBR-2
Modem
or
Fax
EPS
CHIP
LAN 2
Basic minimum installation
Optional
Accessories
Page 5
-803 ARTU
P/N 724855-803
The C-2000 ARTU is the basic
transceiver/PABX unit, and will support up
to nine (9) individual handsets. Connectors
are included.
Weight 15.4 Ibs. Size 6 MCU.
-804 ARTU
P/N 724855-804
The -802 C-2000 ARTU differs from the basic
-801 ARTU by incorporation of a CEPT-E1
interface (dual CEPT-E1 interface on -804).
This provides direct connection to digital
SATCOM systems, cabin management
equipment or other digital data buses while
still maintaining digital air-to-ground
capabilities. Connectors and Y cable
assembly are included.
Weight 15.4 Ibs. Size 6 MCU.
-860 TMU
P/N 724855-860
The C-750 TMU interfaces to both analog
and CEPT-E1 compatible SATCOM equipment
and will support up to nine (9) individual
handsets. Connectors are included.
W12 Cable Assembly shown in picture, must
be ordered separately to allow interface to
CEPT-E1 SATCOM equipment.
Weight 10.0 Ibs. Size 6 MCU.
Accessories
Page 6
Tray Assembly
P/N 724868-802
The tray assembly is the mounting
structure for the ARTU/TMU and
provides power line conditioning, and
air plenum and fan for equipment cooling
during extreme temperatures. Connectors
and W16 cable assembly are included.
Weight 3.0 Ibs. Size 6 MCU
Duplexer
Not required with C-750 TMU
P/N 620317-2
The Duplexer is a passive signal
filter/combiner allowing transmission and
reception from a single antenna.
Connectors are included.
Weight 2.O Ibs. Size 4.5” x 8.3” x 1.0”.
Antenna
Not required with C-750 TMU
P/N 902131-1 (6 hole)
P/N 902131-2 (4 hole)
The antenna is a low drag, 1/4 wavelength
element suitable for high performance
aircraft. The four (4) hole version (P/N
902131-2) is a direct replacement for most
Flitefone antennas. Connector is not included.
Page 7
CDBR-3
P/N 724864-810
The Cabin Distribution Bus Repeater is a tap
device that allows for connection of two (2)
digital devices (handset or CAS) onto the
cabin data bus.
The CDBR-3 is a low-power tap device that
supports installations with up to 50 handsets.
Although only nine may be active at any one
time, this significantly enhances and expands
more elaborate cabin configurations.
External power supply (P/N 726672-801) is
required if more than nine CDBR-3s and/or
other distribution devices are installed.
724855-803, -804 and -860 support 50
handset capability.
Connectors are included.
Weight 0.4 Ibs. Size 4.1” x 3.1” x 1.0”
CAS
P/N 725256-801
The Call Alerting Switch (CAS) provides ten
(10) independent switched outputs to control
call annunciation devices (relays, lights,
sonalerts, etc.) for individual or groups of
telephone handsets. One (1) CAS is used
per system. Connectors are included.
Weight 0.4 Ibs. Size 4.1” x 3.4” x 1.0”.
Model 2 Handsets
Page 8
All Model 2 handsets come with a standard RJ-11 interface. Handsets are available in off-white,
pepperdust, platinum and black (see page 14 for color samples). In addition to color options,
there are four (4) different mounting styles; flush mounted, customized remote cord reel
mounting, curled cord, and bulkhead mounted.
Refer to the following descriptions when ordering for your specific installation.
Relocatable handset
74” Curled Cord
P/N: 724866-804
98” Curled Cord
P/N: 724866-814
Flush mount bezel & handset
58” Cord
P/N: 724866-805
Page 9
Bulkhead mount bezel & handset
58” Cord
P/N: 724866-806
Custom mount handset
64” Cord
P/N: 724866-807
MACH-1 Handsets
Page 10
All MACH-1 handsets come with a standard RJ-11 interface. Handsets are available in off-white,
pepperdust and black. (See page 14 for colors). There are three (3) different mounting styles;
flush mounted, customized remote cord reel mounting, and curled cord. Refer to the following
descriptions when ordering.
Standard flush mount with bezel 58” cord
P/N: 725729-815
Handset shown out of bezel
Custom mount, 58” cord
P/N: 725729-807
Relocatable, 98” cord
P/N: 725729-814
Cable Assemblies
Page 11
lnterface and interconnect cables are available
and can be ordered in varying lengths to custom
configure your MagnaStar ® C-750 or C-2000
installation. To simplify installation activity, data
cable assemblies are terminated at one end.
Refer to the diagram below to select the specific
length and part numbers.
Cable Selection
ARTU
or
TMU
W1
W7
422629-801 (15’)
422629-811 (15’)
422629-802 (30’)
422629-803 (50’)
CDBR-2
422629-812 (30’)
422629-813 (50’)
W7
W6
422629-811 (15’)
AIU
422629-812 (30’)
422629-813 (50’)
4226613-802 (8’)
CDBR-1/3
To Relocatable Handset
4226613-801 (8’)
To Cord Reel Handset
422657-801 (12’)
422635-801 (12’)
W12
W10
CEPT E1
Equipment
CAS
CEPT E1
Equipment
ARTU
724855-804
422657-802
W28
ARTU
724855-804
CDBR-1/3
422657-002 W28
Optional Equipment
Page 12
The following is a list of optional equipment that can be added to the basic MagnaStar ® C-750/C-2000
system. lnterfacing to various SATCOM systems as well as a remote operator/switchboard position
for larger VIP configured aircraft is available.
AIU
P/N 724986-802
The Analog lnterface Unit (AIU) provides for
the connection of analog equipment such as
SATCOM, HF radio and PA systems to the
MagnaStar ® C-750/C-2000 system.
Connectors are included.
Weight 0.8 Ibs. Size 6.5” x 3.1” x 1.0”.
CDBR-2
P/N 902205-803
The Cabin Distribution Bus Repeater, Model 2
(CDBR-2) is recommended for direct analog
FAX and Data connections. The CDBR-2
provides handsfree fax machines and modem
data operation and supports 2 wire or 4 wire
interface for use connecting analog handsets
such as the WH-10 to the system.
The CDBR-2 also retains one standard
connection for a MagnaStar ® digital handset
or Call Alerting Switch (CAS).
Weight 2.0 Ibs. Size is 5.0” x 8.5” x 1.8”
Page 13
CHIP
P/N 726029-802
The Cockpit Headset lnterface Panel (CHIP) is a dzus-rail mounted device
which interfaces the MagnaStar ® C-2000 and C-750 to the aircraft cockpit
headset audio system. The CHlP provides remote dialing capability to the
MagnaStar ® via the CDBR-2.
This direct analog interface allows the cockpit crew to maintain full
headset utilization for both MagnaStar ® calls or normal headset operation
at the touch of a button. The CHIP’s dimensions are identical to the C-118
FLITEFONE ®, Cockpit Controller thus providing ease of installation. The
CHlP features back lighting, off-hook indicator, flash-hook switch and call
alerter output switching. The call alerter output is a 12 volt DC signal
which can be used to drive a signaling device such as a Sonalert or light
annunciator. The CHlP requires connections to an available CDBR-2 analog
port which should be configured for 4-wire audio.
Weight 0. 7 Ibs.
Te s t E q u i p m e n t
& Handset Colors
Page 14
Test Set
Customer Version includes MMT Software
and Cable
P/N 725481-802
The field test set was designed to assist
with final system test and commissioning
of the MagnaStar ® system. The set gives
the installing technician the ability to
upgrade ARTU/TMU software while the unit
remains installed on the aircraft.
Handset Colors
Black
Pepperdust
Platinum
Off-White
Optional Equipment
Page 15
Teledyne Iridium Unit (TIU)
P/N 2244417-1 (single channel)
P/N 2244417-2 (dual channel)
Dimensions
Weight
15.68"L x 2.25"W x 7.6"H
-1 Transceiver Unit 6 lbs.
-2 Transceiver Unit 8.55 lbs.
Tray 2 MCU 2.0 lbs.
Power Requirements
28 Vdc
Operating Frequency Range Satellite Mode 1616-1626.5 MHz
Transmit Power
Satellite Mode 7W max
The Teledyne Iridium Unit (TIU) expands and enhances the communications capabilities
of the MagnaStar ® family products. By providing access to the Iridium satellite
communications services, the TIU allows cabin passengers and flight crews to make
airborne or ground calls from and to anywhere in the world. Ideal to supplement Verizon
Airfone's air-to-ground network service, the TIU provides an alternative to traditionally
expensive SATCOM calls, a source for extra simultaneous channels, or an added
communications network for increased availability and redundancy.
The TIU is available in single or dual channel units that interface through the MagnaStar ®
on-board telephone network, or Private Branch Exchange (PBX), making global calling
capability accessible from any MagnaStar ® handset in the cabin or cockpit.
Beyond just voice services, the TIU supports RS 232 data functions, providing the ability
to make an Internet dial-up connection to access e-mail, websites, private networks, as
well as to receive weather information.
The TIU MagnaStar ® upgrade is available from aircraft OEMs and their associated
completion centers for new aircraft installations and through the MagnaStar ® dealer
network for post-delivery and after-market aircraft installs.
A i r b o r n e D i g i t a l S AT C O M Te r m i n a l
Page 16
High Speed Data SATCOM HSD-128™
Dual Channel Data Terminal HSD-128
P/N 1110 -A- 0001(28 VDC)
1110 -A- 0060 (115 VAC)
Frequency
Channel Speed
Power
Size
Weight
Environmental
1530 to 1660.5 MHz
64K bps
375w @ 28VDC or 115VAC
8 MCU package
10kg (22 lbs)
DO-160D (-40 to +55; SL-55000ft)
DO-178B (HSD channel cards - level E;
Control Processor and HPA - level C)
The Teledyne Controls/ EMS Technologies HSD-128 ™ High Speed /Data (HSD) SATCOM is
here. HSD-128 ™ is the first dual channel global high speed data solution using the new
Inmarsat Swift64 Mobile Network.
You need to be in touch - Time spent in the corporate aircraft needs to be productive.
With bi-directional data throughput fifty (50) times faster than existing aeronautical analog
SATCOM systems, sending and receiving E-mail, surfing the web, or even video conferencing
is a reality. You can continue to work no matter where your aircraft is in the world.
Designed and manufactured by EMS Technologies, a world leader in satellite communications,
Teledyne Controls offers the HSD-128 ™, a dual channel high speed data terminal that
provides global data connectivity at uncompressed data rates up to 128K bps. In addition,
the HSD-128 ™ provides global 64K ISDN (broadcast) and Mini-M Aero (compressed) voice
services. The HSD-128 ™ is compatible with any ARINC 741 Aero-H/H+ SATCOM antenna and
is well matched with the EMS Technologies' AMT-50 antenna. The HSD-128 ™ uses existing
industry standard networking protocols so that it can be easily interfaced and integrated
into the aircraft LAN, providing a fast and global link for multiple users.
SATCOM
Page 17
AMT-50 High Gain Antenna
P/N 0476-A-00377
Frequency
Coverage
Gain
High Gain Antenna
Antenna Driver Assembly
Diplexer/LNA
1525 MHz to 1660.5 MHz
Seamless Hemispherical>95%
12 dBIC
16.2”L x 13”H x 9” W 4.9 lbs
14”L x 2.5”H x 7.8” W 7 lbs
11”L x 2”H x 7.8”W 6 lbs
Features
■ Multi-channel capability
■ Lightweight: 17.9 lbs/8.1 kg total
■ No beam switching
■ Compatible with ARINC 741 avionics
■ 28 VDC power
MagnaStar ® ISDN Terminal Adapter
(MITA):
P/N 902205-804
Provides an interface between the MagnaStar ®
Airborne Telephone System and the High Speed
Data (HSD-128™) SATCOM system, enabling
global Inmarsat 64K ISDN (broadcast quality) and
Mini-M Aero (compressed) voice services via the
MagnaStar’s user interfaces (handsets, data
jacks, etc.)
Weight 2.0 Ibs. Size 5.0” x 8.5” x 1.8”.
Cisco 803 Router
Pre-configured by Teledyne to network multiple
LAN user devices (PC’s) via Ethernet to each
other, as well as to the Euro-ISDN based
HSD-128™ and the GroundLink® high-speed
communication links. Dynamically assigns IP
addresses to computers attached to the LAN and
provides Network Address Translation (NAT),
Connetction on Demand and Bandwidth on
Demand services.
SATCOM
Page 18
CommServer ™
P/N 8868-0007-0001
Size:
Power Consumption:
Power Input:
Qualifications:
Rear Connector:
Weight:
4 MCU form factor
100 watts max
28 VDC standard, 115 VAC,
400 Hz optional
RTCA DO-160D
ARINC 600 Size 2
13 lbs
DESIGNED FOR AIRCRAFT CABIN COMMUNICATION REQUIREMENTS
The Teledyne Controls CommServer ™ is a cabin LAN solution designed and fully qualified
for operation in the demanding airborne environment. The CommServer™ provides the
aircraft cabin with the key capabilities of networking / integrating multiple user PC’s with
each other, while managing optimal interfaces with your SmartCabin™ data communication
links, including the High-Speed Data SATCOM (HSD-128™), the SmartCabin™ GroundLink®
and the MagnaStar ® Airborne Telephone.
Standard services include:
■ Network Address Translation (NAT)
■ Packet Filtering (firewall)
■ Least cost routing over HSD-128, MagnaStar ® and GroundLink ®
■ Connection on demand
■ Bandwidth on demand
■ Persistent Domain Name Server (DNS)
■ Caching proxy server
■ Windows compatible file and printer sharing
AWLU
Page 19
The AWLU enables high speed,
secure, wireless network connectivity
on and off your airplane
P/N 16029-002
Dimensions
Weight
Power
Power Consumption
11.5” H x 6.97” W x 2.0” D
3.15 lb / 1.48 kg
115VAC/400Hz or 28VDC
Less than 20 Watts
Compliant with RTCA DO-160D
Compliant with ARINC 763
The Aircraft Wireless LAN Unit (AWLU) provides wireless LAN network connectivity, both
onboard an aircraft, and between the aircraft and the corporate network.
The AWLU is ARINC 763 (Network Server System) compliant, and is an IEEE 802.11b, or
WiFi TM access point, providing a wireless Ethernet LAN connection for PC's and PDA's
onboard the aircraft. The AWLU eliminates a large portion of the installation cost of
wiring the aircraft for Ethernet, and allows flexible wireless high-speed access to the LAN,
and therefore to the communication links, from anywhere on the aircraft.
The AWLU is also capable of moving large amounts of digital data on/off an aircraft, by
connecting your aircraft to the corporate network via high bandwidth data transfer
capability, at a fraction of the costs of other traditional aircraft communication links.
KEY BENEFITS
High speed transfer rate up to 11M bits per second
Firewall security at access point available
Works with any Wi-FiTM, 802.11b compliant device
Reduced weight - no need for wired LAN
Reduced installation costs - no wired LAN cables or user interface connection
lmproved reliability of cabin communications
No maintenance required
Wireless connection between aircraft and flight or maintenance crew
Seamless communication while passengers move about cabin
No active cooling required
Page 20
GroundLink ®
Form Factor:
4MCU
Connector:
ARINC 600 or ARINC 404
Input Power:
115VAC, 400Hz or 28 VDC
Solid State QAR Replacement -Media
up to 440MB
Weight:
10-15.8 lbs/4.5-7.2kg
CAPABILITIES
The Teledyne SmartCabin ™ GroundLink ® is a high bandwidth terrestrial data connectivity solution
designed to operate in the demanding corporate aircraft environment. The GroundLink ® enables corporate
aircraft travelers to access e-mail accounts, browse the web, transfer data files, or access Virtual Private
Networks (VPN) over a live high-speed IP connection while the aircraft is on the ground. Travelers can
use this live connection on their corporate aircraft as a remote office link while parked, store large files in
flight for post-flight forwarding, uplink large data files and refresh on-board server content all at service
rates well below that offered from satellite based systems designed for airborne operation.
■ Simultaneous use of up to 8 full duplex radios
■ Support for multiple cellular/PCS standards and frequencies
– CDMAOne/CDMA2000 at 900 or 1900 MHz
– GSM/GPRS at 800, 1800 or 1900 MHz
– Other emerging standards
■ Multiple standards can be supported in same unit
■ Ethernet interface to cabin LAN to support multiple user PC’s
■ Front panel mounted antennas (remote mount optional) eliminating external fuselage
installation concerns
■ RF interlock prevents airborne transmission
■ No investment in infrastructure – uses existing network provided by service providers
■ Data encryption and compression supported
Page 21
TeleLink ® TL-608
Form Factor:
1MCU per ARINC 600
Input Power:
28 V DC
Qualification:
RTCA DO-160C
Weight:
2.2 kg or 4.63 lbs
TeleLink®, is a datalink system for digital
messaging between aircraft and ground networks.
Teledyne Controls' TeleLink® meets the unique
communications needs of the corporate or regional
airline pilot by providing a variety of features and versatile connectivity options
in a small, low-cost, lightweight package.
The TeleLink® datalink system exceeds current datalink requirements providing
VHF ACARS, SATCOM & Airborne phone links. TeleLink® has been designed to
comply with the ADS (Automatic Dependent Surveillance) functions of the
communications, Navigation and Surveillance/Air Traffic Management
(CNS/ATM) programs of the Future Air Navigation System (FANS).
Teledyne Controls pioneered ACARS for the commercial aircraft industry. Now,
operators of business or commuter aircraft can realize the benefits of digital
datalink and CNS/ATM with TeleLink.
TeleLink TL-608 digital data communications controller applies years of ACARS
experience to the most up-to-date hardware technology available. This
combination means that a whole new group of aircraft operators can now
realize the benefits of ACARS at an affordable price. Benefits such as two-way
messaging, predeparture clearances, digital ATIS, flight planning and following,
textual and graphical weather, and more.
TELEDYNE CONTROLS
A Teledyne Technologies Company
12333 West Olympic Boulevard
Los Angeles, CA 90064 USA
Tel: 1-888-246-STAR (7827)
www.teledyne-controls.com
Our SmartCabin Office™ Partners: