crimp terminals - R

Transcription

crimp terminals - R
CRIMP TERMINALS
CRIMP TERMINALS: CAST BATTERY LUGS
CAST COPPER BATTERY LUGS
Manuf: Waytek Inc.
Manuf: Waytek Inc.
Manuf: QuickCable Part No: HexCrimp #4255-001 or HexCrrmp Jr. #4247-001
Manuf: Amp, Roto-Crimp hand tool
Part No: 600850 or 600850-1
Manuf: Molex, Part No: 19078-0007
Two crimps may be required on wire sizes 4-4/0 g
3
Amp Roto-Crimp Tool
Quick Cable and Molex Crimp Tool
4
CRIMP TERMINALS
CRIMP TERMINALS: CLOSED END
12-22 ga and 10-16 ga
8 GA
5
CRIMP TERMINALS
CRIMP TERMINALS: CLOSED END
Hoffman Products (Cadillac Electric) For 22-10 ga.
Part No: YS2210
Hoffman Products (Cadillac Electric) For 8 ga.
Part No: YS8S
Molex
For 22-10 ga Part No: 64001-0600
For 8 ga Part No: 64001-2500
NTM (Nichifu) For 14-10-8 ga Part No: NH-36B
NTM (Nichifu) For 22-10 ga part No: NH-37
6
CRIMP TERMINALS
HEAVY DUTY LUGS AND SPLICES NON INSULATED
LIGHT DUTY TERMINALS (16-10 ga)
For16-14-10-8 ga. Non Insulated terminals and lugs
Manuf: Paladin. Part No: Die only #2031 and
Manuf: Waytek Inc.
CrimpAll tool frame #8000
Manuf: Amp Part No: 1526955-1
Manuf: Molex
7
8
CRIMP TERMINALS
CRIMP TERMINALS: POWERPOLE 175A
POWERPOLE (SY) SB175 AMP CONNECTOR
4 ga Contract, Part No: SY944-2
Wire strip length 1 1/8”
Manuf: Waytek Inc.
Manuf: Waytek Inc.
Manuf: QuickCable Part No: HexCrimp #4255-001 or HexCrrmp Jr. #4247-001
Manuf: Amp, Roto-Crimp hand tool Part No: 600850 or 600850-1
9
CRIMP TERMINALS
CRIMP TERMINALS: RED BLUE YELLOW
SOLDERLESS CRIMP TERMINALS AND SPLICES,
NYLON INSULATED, DOUBLE CRIMP STYLE
(THIS REPRESENT SOME OF THE MANY CHOICES AVAILABLE IN CRIMP TERMINALS)
NYLON DOUBLE CRIMP STYLE (THE ONES WITH THE COPPER SLEEVE OVER THE TERMINAL BARREL) ARE THE BEST FOR
HIGH VIBRATION ENVIRONMENTS BECAUSE THEY SUPPORT THE WIRE INSULATION WHERE IT EXITS THE TERMINAL
Manuf: Paladin Tools
Manuf: Paladin Tools
Crimp Tool Frame #1302
CrimpALL Tool Frame #8000
Manuf: Paladin Tools
Insulated Terminals
Manuf: Eclipse Tools
Flag Terminals
DIE ONLY#2035
DIE ONLY #300-070
RED 22-16 ga crimp height=.109 - .115”
BLUE 16-14 ga crimp height=.119 - .125”
YELLOW 12-10 ga crimp height=.169 - .175”
NOT RECOMMENDED
CAN’T DO A GAS TIGHT CRIMP
Strip length Terminals:
Red=7/32”
Blue=7/32”
Yellow=5/16”
Strip length Butt splice:
Red=1/4”
Blue=1/4”
Yellow=3/8”
10
REAR VIEW
This is what your crimped connectors should look like, oval shaped and uniform. This was crimped on a double crimp tool. In
the center photo (wire at the inlet side) note the oval shape that the wire and insulation has been formed into. This is caused
by the insulation crimp sleeve being formed around the wire. The photo on the far right is so that you could see the solidity of
the crimp.
McMaster Carr
Unicon 3 Universal
Conversion Tool
Paladin Tools Pneumatic Hand
Tool Operator
11
CRIMP TERMINALS
CRIMP TERMINALS WITH HEAT SHRINK
HEAT SHRINK COVERED CRIMP TERMINALS
Wire strip length for red, blue & yel=5/16”
Seller: Waytek Wire.
Manuf: Molex, Part No: 64016-0041
Rosta Tool Co. (Sargent Quality Tools)
Manuf: Thomas & Betts (Sta-Kon) Part No: WT1255
Manuf: Tyco (Raychem) Part No: AD-1522
DELPHI
12

Similar documents