Be Crafty.

Transcription

Be Crafty.
PAGE 1
Be Crafty.
Technique Tutorial
How To Apply a Press Lock with Screws
Totes, handbags and other accessories often need a secure closure. Something more than
a hook & eye or snap, yet something that is visually appealing. Consider a press lock
for quick and easy access, style, and security. They are easy to apply and so professional!
Just follow the tutorial below to see how this hardware is attached!
© Prym Consumer USA
PAGE 2
Be Crafty.
Technique Tutorial
How To Apply a Press Lock with Screws
What are the parts of a Press Lock?
Before getting started, let’s familiarize ourselves with the parts of this lock. The
press lock is meant to be installed on the flap of your project with screws. The base
plate is designed to be installed on the body or base of the project; the flat washer
with holes anchors the base plate and is hidden between the lining and the exterior.
719-65: Each lock set includes Press Lock with screws, Base Plate,
and Washer.
Press Lock
Screws
Washer
Base Plate
with prongs
© Prym Consumer USA
PAGE 3
Be Crafty.
Technique Tutorial
Instructions
How To Apply a Press Lock with Screws
Supplies:
Your project
Heavy Weight Iron-On Interfacing – about 4” square
Dritz® Press Lock (#719-65)
Tiny Phillips Head Screwdriver
Dritz® Marking Pencil
Sharp Small Scissors
Dritz® Fray Check®
Plastic Canvas (optional)
BEFORE APPLYING THE LOCK: Read through this tutorial and your pattern instructions
before starting so you can plan the best order for installing your lock. Cut out your project,
choosing the position of the lock in advance. Projects vary and so may the construction order.
Because the washer and prongs of the base plate need to be hidden beween the outer fabric
and the lining, we give a general sewing order. For simplicity we have drawn the project as a bag.
Follow the instructions for your project and use the lock instructions at the appropriate time.
Since a press lock gets pushed and pulled when in use, we call for heavy iron-on interfacing
as well as suggesting plastic canvas for additional reinforcement.
Prepare the Flap
1.
2.
Your pattern instructions probably call for an
interfaced flap. Add a second layer of interfacing to the flap where the lock will attach.
Cut the lock interfacing about 1 1/2” wide x 1”
high. Place it glue side down on the wrong
side of the fabric, flush to the seam line. If
you have interfaced the entire flap, fuse this
piece on top of the original interfacing, following package directions.
Complete the flap following pattern
directions.
1.
Wrong side of flap fabric
NOTE:
For best results the flap should be
no thicker than 1/8” to fit properly into
press lock #719-65.
© Prym Consumer USA
PAGE 4
Be Crafty.
Technique Tutorial
How To Apply a Press Lock with Screws
Apply the Press Lock
3.
Use a tiny Phillips Head screwdriver to
remove the two screws on the back of the
lock.
3.
4.
Right side of flap
TIP:
Place a cloth under the lock when
removing and applying screws to prevent
losing these extremely small parts.
4.
5.
6.
Slide the press lock onto the edge of the flap,
face up, in the desired location. Make sure
flap is fully inserted into lock.
5.
6.
Use a marking pencil to mark each hole on
the wrong side of the flap.
Remove the lock and use an awl or tiny
scissors to poke through the marked holes.
Make the hole as small as possible.
Wrong side of flap
Slide lock back onto flap, aligning holes.
Replace the screws and tighten.
TIP:
Place the press lock on a fabric
covered work surface while working to
prevent scratching.
8.
0.75 FL OZ (22 ml)
8.
7.
Stops Fraying on Fabric!
Put Fray Check® on the edge of the cut holes
to prevent raveling.
DANGER! FLAMMABLE. MAY CAUSE EYE
IRRITATION. Keep away from sources of ignition.
Do not smoke. Do not get in eyes. Read back
panel.
7.
© Prym Consumer USA
PAGE 5
Be Crafty.
Technique Tutorial
How To Apply a Press Lock with Screws
Apply the Base Plate
9.
10.
11.
Fuse a small square of interfacing to the
wrong side of the base fabric where the
base lock position is planned. If possible
leave the lining open so that the back of
the base plate can be accessed. This also
allows you to conceal the prongs.
9.
Insert the press lock into the base plate.
Fold the flap into position on the bag.
Wrong side of fabric
Right side of flap
Press the base plate against the fabric of
the bag to make indentations. Use a marking pencil to mark each indentation.
TIP:
Plan position of base plate carefully.
Once holes are snipped you cannot change
the position of the lock.
12.
The base plate must be straight. Use a ruler
to double check the position of your marks;
then position the base plate to check again
before cutting. Use a sharp tiny scissors to
cut a hole at each indentation. Put Fray
Check® on the holes to prevent raveling. Be
sure to only cut through outer fabric.
10.
11.
12.
NOTE:
Holes are cut through all layers except
the lining. If possible, leave lining in tact
to conceal the prongs. When base plate is
attached, hand stitch the lining closed.
Stops Fraying on Fabric!
DANGER! FLAMMABLE. MAY CAUSE EYE
IRRITATION. Keep away from sources of ignition.
Do not smoke. Do not get in eyes. Read back
panel.
0.75 FL OZ (22 ml)
© Prym Consumer USA
PAGE 6
Be Crafty.
Technique Tutorial
How To Apply a Press Lock with Screws
OPTIONAL PLASTIC
CANVAS:
For extra strength add a layer of plastic
canvas between the interfacing and the
washer. Cut the plastic canvas slightly
smaller than the interfacing. Position it over
the prongs, cutting the canvas where
prongs touch the canvas. Attach the washer
and fold down the prongs as in Step 14.
13.
Push the prongs through the holes from
right to wrong side. If you are using the
optional plastic canvas, position it now.
Place the washer over the prongs.
14.
Firmly press the prongs toward the
center of the washer to secure.
15.
Finish your project by pinning and
stitching the lining closed.
13.
Plastic Canvas
Wrong
side
of fabric
Interfacing
Optional Plastic Canvas
14.
© Prym Consumer USA

Similar documents

Be Crafty.

Be Crafty. tiny scissors to cut a hole at each indentation. Put Fray Check® on the holes to prevent raveling. Be sure to only cut through outer fabric.

More information

Be Crafty.

Be Crafty. for quick and easy access, style, and security. They are easy to apply and so professional! Just follow the tutorial below to see how this hardware is attached!

More information