9069193 Side Jamb Liner Top Insert Replacement

Side Jamb Liner Top Insert Replacement
for E-Series Double-Hung and Single-Hung Windows
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com
Please leave this guide with building owner.
▶▶ Read guide from beginning to end before starting maintenance procedure. Read all warnings and cautions during unit maintenance.
▶▶ For information, calculating, and design pressure ratings for E-Series windows and doors go to
www.eaglewindow.com/Wintelligence/Design-Pressure-Estimator.aspx
▶▶ Check with your local building code official to identify and confirm compliance with local building code requirements.
Parts Included
(1) Side Jamb Liner Top Insert
Tools Needed
∙∙ Safety Glasses
∙∙ Flat Blade Screw Driver
∙∙ Needle Nose Pliers
∙∙ Finish Nailer (for monumental units only)
∙∙ Pliers (for monumental units only)
∙∙ Putty Knife (for monumental units only)
Side Jamb Liner Top Insert
Supplies Needed
∙∙ Denatured Alcohol
∙∙ Clean Cloth
Windows and doors can be heavy. Use safe
lifting techniques and a reasonable number of
people with enough strength to lift, carry and
install window and door products to avoid injury
and/or product damage.
Use caution when working at elevated
heights and around unit openings. Follow
manufacturers’ instructions for ladders and/
or scaffolding. Failure to do so may result in
injury or death.
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved.
Follow manufacturers’ instructions for hand
or power tools. Always wear safety glasses.
Failure to do so may result in injury and/or
product damage.
9 0 6 9 1 9 3 BA
Revised 06/03/13
1
2
Interior Side Stop
Interior
Interior
Putty Knife
Lock
Handles
Interior Side Stop
Pliers
4 Inches
For Monumental Only
▶▶ For single and double hung units proceed to step 2.
Pry interior side stop away from frame. Repeat on opposite side. Remove any nails from frame and
interior side stops.
Unlock window and raise bottom sash 4".
3
4
5
Interior
Interior
Interior
Bottom Sash
Lock
Handles
Bottom Sash
Single Hung and Monumental Only
Rotate and hold lock handles toward center
while tilting sash in 90 degrees.
7
6
Interior
Pivot bottom sash to remove from window
frame as shown. Place sash on clean flat work
surface, exterior side up.
▶▶ For double hung units proceed to step 6.
6 Inches
8
Tilt
Latch
Interior
Remove sash stop from the side jamb.
Interior
Top Sash
Tilt
Latches
Lower top sash 6”.
9 0 69193
Slide tilt latches inward while tilting sash in
90 degrees.
2
Pivot top sash to remove from window frame
as shown. Place sash on clean flat work
surface, exterior side up.
9
10
Interior
Interior
Pocket Cover
Grasp jamb liner pocket cover at bottom and
pull outward and down from behind head stop
to remove and save for reuse.
Balance
Shoe
Balance shoes are
under high tension.
Use flat blade
screwdriver with long
handle so that both
hands can be used 2nd
to release balance
tension. Suddenly
releasing balance
shoe could damage
window unit.
Cam in locked
position
Shoe
Balance
Cam
Flat Blade
Screwdriver
1st
Cam in unlocked
(travel) position
Insert flat blade screwdriver into cam slot, apply firm downward pressure, and rotate 1/4 turn. Hold
firmly allowing shoe to rise until it stops. Repeat for second shoe in side jamb.
11
12
Interior
Interior
Jamb Liner
Exterior Insert
12 Inches
Sill
Cushion
Flat Blade
Screwdriver
Remove existing sill cushion and save for reuse.
Slide outside side jamb liner insert up 12”.
13
14
Interior
Interior
Jamb
Liner
Jamb Liner
Remove side jamb liner working from bottom to top, prying jamb liner
edge from frame to disengage as shown.
9 0 69193
Pull jamb liner down slowly, while supporting head stop and remove from
frame. Place jamb liner on a clean flat work surface with balance side up.
3
15
16
Needle Nose
Pliers
Jamb Liner
Jamb Liner Top
Weatherstrip
17
Top Insert
Top Insert
Head End
Jamb Liner
Head End
Head End
Top Insert
Remove upper jamb liner weatherstrip. Save
for reuse.
18
Jamb Liner
Remove top insert from side jamb liner as
shown and dispose of properly.
Slide new top insert into side jamb liner.
19
Jamb Liner
Dust Pad
Interior
Kerf
Head
Stop
Jamb Liner Top
Weatherstrip
Insert side jamb liner behind head stop.
Insert new or existing side jamb liner top weatherstrip into kerf.
20
21
Interior
Interior
Interior
Side
Stop
Jamb Liner
Jamb Liner
Position side jamb liner in frame, locking front lip behind interior
side stop.
9 0 69193
Re-engage side jamb liner, working from bottom to top, pressing jamb
liner edge into frame to engage as shown.
4
22
Interior
23
Locked
Position
Balance
Shoe
Interior
Shoe
Balance
Cam
Jamb Liner
Exterior Insert
Flat Blade
Screwdriver
Unlocked
Position
Insert flat blade screwdriver into cam and pull down until shoe is
aligned with shoe on opposite side. Rotate cam ¼ turn to lock.
Slide outside side jamb liner exterior insert down to sill.
24
25
Interior
Interior
Wide End
Side Cutting
Pliers
Jamb Liner
Channel
Clean Cloth and
Denatured Alcohol
Sill Cushion
Sill Cushion
Clean area with a clean cloth and denatured alcohol.
Remove release liner. Position wide end of sill cushion in jamb liner
channel, adhesive side down, and press into place.
26
27
Interior
Interior
Tilt
Latches
Balance
Shoes
Pivot Pin
Tilt Latches
Tilt sash up, retracting tilt latches by sliding inward. Release tilt latches to
re-engage sash in frame. Verify top sash operation. Repeat steps 26-27 if
sash does not operate correctly.
▶▶ For double hung units proceed to step 29.
Rotate top sash to engage pivot pins into balance shoes of exterior
channel. Push down until both pivot pins are fully engaged.
9 0 69193
5
28
29
Interior
Interior
Beveled Side
Head
Stop
Sash Stop
Jamb Liner
Pocket Cover
Interior
Channel
Single Hung and Monumental Only
Replace sash stop in the side jamb.
30
Interior
Insert top of jamb liner pocket cover, beveled side toward exterior, into
interior channel, sliding it up behind head stop. Press jamb liner pocket
cover firmly into place, starting at top, zippering down full length.
31
Balance
Shoe
Interior
Interior
Channel
Lock
Handles
Pivot Pin
Rotate bottom sash to engage pivot pins into balance shoes of interior
channel. Push down until both pivot pins are fully engaged.
Tilt sash up, retracting tilt latches by rotating lock handles toward center,
then release lock handles to re-engage sash.
32
33
34
Interior
Interior
Interior
Interior
Side
Stop
Lock
Handles
Lock
Handles
For Monumental Only
Verify sash operation. Repeat steps 30-31 if
sash does not operate correctly.
9 0 69193
Close and lock sash.
▶▶ Side jamb liner top insert replacement procedure is complete for single and double hung units.
▶▶ For monumental units proceed to step 34.
6
Reapply interior side stop on frame. Repeat
on opposite side. Fasten with finish nailer.
▶▶ Side jamb liner top insert replacement procedure is complete for monumental units.