FinePix 4700 ZOOM OWNER`S MANUAL

This manual will show you how to use your FUJIFILM DIGITAL CAMERA
FinePix4700 ZOOM correctly. Please follow the instructions carefully.
BB10959-200 (1)
Warning
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The graphical symbols are located on the bottom
of the case.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
For customers in the U.S.A.
FCC Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two
conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
2
CAUTION
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment
and receiver.
— Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or
modifications not expressly approved in this manual
could void your warranty.
For customers in Canada
CAUTION
This Class B digital apparatus complies with
Canadian ICES-003.
Please read the Safety Notes (➡P.120)
and make sure you understand them
before using the camera.
3
Contents
Preface..................................................................... 6
Camera Features and Accessories..................... 7
Nomenclature ......................................................... 8
1 Getting Ready
ATTACHING THE STRAP ................................... 15
SELECTING THE POWER SUPPLY.................. 16
● Using Batteries................................................. 16
● Using the AC Power Adapter .......................... 18
LOADING AND REMOVING THE SmartMedia™ ...... 19
SWITCHING ON AND OFF ................................. 21
SETTING THE DATE AND TIME ........................ 22
2 Basic Photography
4
TAKING PICTURES(AUTO MODE) ................... 24
● Number of Available Frames .......................... 29
USING AF/AE LOCK ............................................ 30
FRAMING GUIDELINE FUNCTION.................... 32
VIEWING YOUR IMAGES (PLAYBACK) ........... 34
FAST FORWARDING IMAGES .......................... 35
PLAYBACK ZOOM............................................... 36
MULTI-FRAME PLAYBACK ................................ 37
ERASING SINGLE FRAME ................................. 38
USING A TV MONITOR ....................................... 40
3 Advanced Features
ADVANCED FEATURES PHOTOGRAPHY ...... 41
◆Photography mode specifications..................... 41
PHOTOGRAPHY MODE ............................................... 41
3 AUTO ............................................................ 42
7 PORTRAIT ................................................... 42
6 LANDSCAPE ............................................... 42
8 NIGHT SCENE............................................. 43
4 MANUAL....................................................... 44
5 CONTINUOUS SHOOTING ....................... 45
9 MOVIE .......................................................... 47
PHOTOGRAPHY MENU ............................................... 50
G SETTING THE BRIGHTNESS
(EXPOSURE COMPENSATION).................... 51
M FLASH BRIGHTNESS ADJUSTMENT ........ 52
A SETTING THE WHITE BALANCE ............. 52
B SETTING THE SENSITIVITY ..................... 53
C SETTING THE MANUAL FOCUS .............. 54
h PHOTOMETRY ........................................... 55
` SHARPNESS ............................................... 56
W PREVIEW DISPLAY .................................... 57
AUTO BRACKETING .................................. 58
FLASH PHOTOGRAPHY .................................... 59
x Auto flash mode ........................................... 60
Z Red-Eye Reduction ...................................... 60
vForced Flash ................................................... 61
w Night Scenes (Slow Synchro) ...................... 61
a Suppressed Flash ........................................ 62
Y MACRO(CLOSE-UP) PHOTOGRAPHY ....... 63
b SELF-TIMER PHOTOGRAPHY ..................... 64
DIGITAL ZOOM .................................................... 66
4 Advanced Features Playback
ADVANCED PLAYBACK ..................................... 67
◆Playback mode menu ....................................... 67
MOVIE PLAYBACK .............................................. 68
PLAYBACK MENU
L ERASING SINGLE•ALL FRAME/FORMATTING ...... 71
N PLAYBACK (AUTOMATIC PLAYBACK) ....... 73
RESIZE ......................................................... 74
P SETTING AND REMOVING
SINGLE-FRAME PROTECTION ................ 76
P SETTING AND REMOVING
PROTECTION FOR ALL FRAMES............ 78
HOW TO SPECIFY PRINT OPTIONS ............. 80
[ DPOF DATE SETTING ............................... 81
[ DPOF SET FRAME ..................................... 82
[ DPOF REVIEW/CANCEL........................... 86
[ DPOF SET ALL/CANCEL ALL................... 88
U CREATE INDEX .......................................... 90
E
5 Setting
SET-UP MODE ..................................................... 92
SETTING THE IMAGE QUALITY........................ 94
SETTING THE FILE SIZE .................................... 95
FRAME NO. MEMORY ........................................ 96
STARTUP SCREEN............................................. 97
ADJUSTING THE LCD MONITOR BRIGHTNESS
AND THE SPEAKER VOLUME ............................ 99
System Expansion Options ................................. 100
Using the USB Cables and
the Software Included ........................................ 101
Optional Accessories Guide ................................ 103
Explanation of Terms ........................................... 105
Notes on Using Your Camera Correctly ............. 106
Notes on the Power Supply ................................. 107
● Applicable Batteries .......................................... 107
● Notes on the Batteries ...................................... 107
● Notes on Using the Battery Charger ............... 108
● BC-NH Battery Charger Specifications ........... 109
● Notes on Using the AC Power Adapter........... 109
Notes on the SmartMediaTM ................................. 110
Warning Displays ................................................. 112
Troubleshooting.................................................... 115
Specifications ....................................................... 118
Safety Notes ......................................................... 120
EC Declaration of Conformity .............................. 123
1
2
3
4
5
5
Preface
■ Test Shots Prior to Photography
of water and induce vomiting. Then seek medical assistance.
For particularly important photographs (such as weddings and
overseas trips), always take a test photograph to check that the
camera is functioning normally.
● Fuji Photo Film Co., Ltd cannot accept liability for any
incidental losses (such as the costs of photography or the loss
of income from photography) incurred as a result of faults with
this product.
■ Notes on Electrical Interference
■ Notes on Copyright
Images recorded using your digital camera system cannot be
used in ways that infringe copyright laws without the consent of
the owner, unless intended only for personal use. Note that
some restrictions apply to the photographing of stage
performances, entertainments and exhibits, even when
intended purely for personal use. Users are also asked to note
that the transfer of memory cards containing images or data
protected under copyright laws is only permissible within the
restrictions imposed by those copyright laws.
■ Liquid Crystal
6
Camera Features and Accessories
If the LCD monitor or LCD panel is damaged, take particular
care with the liquid crystal in the monitor or panel. If any of the
following situations arise, take the urgent action indicated.
● If liquid crystal comes in contact with your skin
Wipe the area with a cloth and then wash thoroughly with
running water and soap.
● If liquid crystal gets into your eye
Flush the affected eye with clean water for at least 15minutes
and then seek medical assistance.
● If liquid crystal is swallowed
Flush your mouth thoroughly with water. Drink large quantities
Do not use this device in aircraft or hospitals. The use of this
device in an aircraft or hospital can cause malfunctions in the
control devices used in the aircraft or hospital.
Features
■ Explanation of Color Television System
● The newly developed Super CCD which delivers an high
resolution image file with 4.3 million pixels.
● Built-in 3✕ zoom lens with a low-dispersion aspherical lens for
superb optical performance
● Compact and lightweight aluminum-magnesium alloy body
● Quick, responsive operation with 2-second startup and 1
second between shots.
● Fast ISO 200 film speed and built-in automatic flash allow
shooting in a wider range of situations.
● Auto focus with macro function (manual focus also available)
● Automatic shooting modes that can be tailored to subjects in
different photography conditions
● Manual photography mode that allows fine tuning of the
photography settings
● Convenient preview function for quickly checking of your shots
● Smooth digital zoom function (1.88✕ at megapixel resolutions)
and playback zoom function (up to 15✕)
● The Framing Guideline function makes it easy to compose
perfectly balanced shots.
● Continuous shooting function even at maximum resolution.
● Movie shooting function (320 ✕ 240 pixels with sound)
● 2-inch 130,000-pixel low-temperature polysilicon TFT LCD
monitor
● Select your favorite image as the startup screen.
● Dot-matrix LCD panel simplifies camera operation.
● USB connection for quick and easy image data transmission
NTSC :
● Conforms to the new standard for digital camera file
■ Handling Your Digital Camera
This camera contains precision electronic components. To
ensure that images are recorded correctly, do not subject the
camera to impacts or shocks while an image is being recorded.
■ Trademark Information
● IBM
PC/AT is a registered trademark of International Business
Machines Corp. of the USA.
● iMac and Macintosh are registered trademarks of Apple
Computer, Inc.
● Windows is a registered trademark of the Microsoft
Corporation of the U.S. registered in the USA and other
countries.
Windows is an abbreviated term referring to the Microsoft
Windows Operating System.
● SmartMedia is a trademark of Toshiba Corporation.
● Other company or product names are trademarks or registered
trademarks of the respective companies.Trademark
Information
PAL :
National Television System Committee, color
television telecasting specifications adopted mainly in
the U.S.A., Canada and Japan.
Phase Alternation by Line,a color television system
adopted mainly by European countries and China.
Accessories
● SmartMedia
● Hand Strap (1)
(16MB, 3.3V) (1)
Supplied with:
• Anti-static case (1)
• Index label (1)
● A/V Cable (approx. 1.5m
(4.9 ft.), mini-plug (2.5mm
dia.) to pin-plug cable) (1)
● AA-size Nickel Metal
Hydride (Ni-MH) batteries ● Interface Set (1)
HR-3UF (2)
• CD-ROM (1)
• USB Cable (1)
• Quick Start Guide (1)
• Noise suppression core (1)
● Owner’s Manual
(this manual) (1)
● Battery Charger BC-NH(1)
system✽
✽ Design rule for Camera File System.
● Supports DPOF (Digital Print Order Format) for simple print
ordering
7
Nomenclature
✽
Refer to the pages in parentheses for more details.
Viewfinder window
Shutter button
Photography
Mode dial(P.12)
Viewfinder(P.26)
Flash(P.59)
Mode switch(P.12)
POWER button(P.12)
Strap mount(P.15)
Microphone(P.47)
Flash control sensor
Flash pop-up button(P.59)
DISP button(P.32·37)
LCD panel(P.10)
4-direction button(P.10)
MENU/EXE button
Speaker(P.99)
Self-timer lamp(P.65)
Lens/Lens Cover
SHIFT/r button
Viewfinder lamp(P.28)
CANCEL/BACK button
SmartMedia slot cover
release button(P.19)
DIGITAL(USB)
socket(P.102)
A/V OUT
(audio/visual output)
socket(P.40)
SmartMedia slot cover(P.19)
SmartMedia slot(P.19)
Battery cover(P.17)
Tripod mount
LCD monitor
DC IN 3V (power input)
socket(P.18)
8
9
Nomenclature
LCD panel
LCD Display Details
4-direction button
setting display (a)
Mode display
4-direction button
setting display (d)
0 Mode
Photography
Icons are displayed on the LCD panel to help with different camera operations. Use these icons as a
guide to using the 4-direction button.
4-direction button
Up •
Zoom
Telephoto •
Flash
No. of remaining shots
/Remaining time
Down •
Manual •
Auto •
Portrait •
Left •
Right
Wide angle
x Auto •
Red-eye Reduction •
Macro
ON •
OFF
Self-Timer
ON •
OFF
Manual Focus
Moves the focus closer •
Image Quality
FINE •
File Size
2400✕1800 •
Playback
1 Mode
10
Continuous Shooting •
Night Scene
Night Scenes(Slow Synchro) •
4-direction button
setting display (b )
mode, the number of remaining shots or remaining time, the quality setting, resolution, flash setting,
macro setting and self-timer setting.
✽ When the Mode switch, Power button or “SHIFT/r”button is used, the LCD panel will light up orange
for 5 seconds in Photography mode and in green for 5 seconds in Playback mode.
Movie •
Framing Guide
4-direction button
setting display (c)
✽ This panel allows you to check and modify camera settings such as the photography or playback
Setup •
Landscape •
Moves the focus further away
NORMAL •
Still image •
BASIC
1280✕960 •
Movie •
Frame Advance
Previous image •
Playback Zoom
Zoom Up •
Movie Playback
Play/Pause •
Forced Flash
Suppressed flash
640✕480
Zoom/Trimming •
Playback •
Reverse playback•
Paused
Next image
Zoom Down
Reverse playback •
Fast forward •
Rewind •
Stop •
Movie frame advance
Page Advance
Previous page •
Next page
11
Nomenclature
Mode switch
Photography Mode dial
Mode switch
Photography mode
Power button
2
Setup
(➡P.92)
In this mode, you can set the image quality, file size, sharpness, Auto
Power-Off function, frame number memory, buzzer tone, Startup screen,
date and time settings.
9
Movie
(➡P.47)
Allows movies (320✕240 pixels, 10 fps, AVI format with sound) up to 80
seconds long to be shot in the same file.
5
Continuous shooting
(➡P.45)
You can shoot up to 3 frames at intervals of 0.2 seconds. The manual focus
and Auto Bracketing (3 consecutive frames) functions can also be used.
4
Manual
(➡P.44)
Allows you to check your image before it is recorded. In this mode, you
can also specify the settings for Brightness (exposure compensation),
Flash Brightness Adjustment, White Balance, Sensitivity. Manual Focus,
Light Metering Mode, Sharpness and Preview.
Playback mode
Photography Mode dial
Continuous shooting
Movie
Manual
Setup
Auto
Shutter button
Auto
3
(➡P.24·42)
7
Portrait (➡P.42)
6 Landscape (➡P.42)
Night Scene
Portrait
Night Scene
8 (➡P.43)
This is a simple and convenient photography mode in which the camera
automatically controls settings such as the exposure to suit the shooting
conditions. This mode is ideal for general photography where you are not
trying to achieve any particular effect.
Use this mode for shots of people.
Use this mode for shots of distant objects such as landscapes.
Use this mode to shoot pictures at night. You can also use manual focus
in this mode.
Landscape
12
13
Ready
1 Getting
Nomenclature
ATTACHING THE STRAP
Example of LCD Monitor Text Display • Shooting
1
Photography Mode
YMacro photography icon
bSelf-Timer photography icon
Zoom bar
2
Number of remaining shots
oCamera shake warning
p Battery low warning
AF frame
Date
Pass the loop of thin cord on the end of the strap
through the strap mount.
Example of LCD Monitor Text Display • Playback
Then pass the other end of the strap through the
loop of thin cord and pull the strap tight.
1
Playback frame number
Playback mode
p Battery low warning
F Protection
K DPOF
Date
Time
＊The above screen shows the NTSC model. The date order differs in the PAL model (day. month. year).
14
Some items are displayed depending on the camera mode and photography conditions.
15
SELECTING THE POWER SUPPLY
Using Batteries
1
2
3
The FinePix4700 ZOOM takes 2 nickel-metal
hydride (Ni-MH) or Ni-Cd batteries. The two
batteries used should both be of the same type.
◆Number of available shots (with fully charged batteries)
The table below provides a guide to the number of shots
that can be taken at normal temperature with 50% flash
use. Note that these figures may vary depending on the
camera’s ambient temperature and the level of battery
charge.
LCD monitor
on
LCD monitor
off
Ni-MH battery HR-3UF
Approx. 80
Approx. 230
Ni-Cd battery KR-3UF
Approx. 50
Approx. 140
Battery Type
◆Notes on the Batteries◆
It is also possible to take some shots using
alkaline batteries if you use the viewfinder
(➡P.24). However, due to the nature of
alkaline batteries, they can only be used for
extremely short periods and they may not
work at all in cold conditions.
● Lithium or manganese batteries should not be
used at all as they emit heat and can damage
the camera.
● Do not use old and new batteries together.
●
16
Load the rechargeable batteries into the battery
charger as indicated on the label.
◆ Batteries that Can Be Charged ◆
AA-size Ni-MH batteries
Fujifilm HR-3UF : 2 (supplied with the camera
or sold separately)
● AA-size Ni-Cd batteries
Fujifilm KR-3UF: 4 (sold separately)
●
! Use only the designated batteries. Batteries other than
●
AA-size Ni-MH or Ni-Cd batteries cannot be recharged
in the BC-NH.
! Attempting to charge batteries other than those specified
●
for use with the charger (such as manganese, alkaline or
lithium batteries) can cause the batteries to burst or leak.
This could result in a fire or injury and consequent
damage to the surroundings.
Plug the charger into a power outlet to begin
charging. Battery charging will be completed in
about 13 hours, but the power lamp remains lit.
Unplug the battery charger from the power outlet
when it is not in use.
Slide the “battery cover” in the direction of the
arrow and open the cover.
! Ni-MH batteries are not fully charged at shipment and
●
batteries. If the camera is left switched on, the
camera settings may revert to the factory default
settings.
! If the AC power adapter has been connected or the
●
batteries have been installed for about half a day or
longer, the camera settings will be retained for about
half a day after the AC power adapter has been
disconnected and the batteries have been removed.
Check the date setting after you replace the
batteries.
must be charged before being used.
! Fully discharged Ni-MH batteries take approximately 12
●
hours (1450 mAh) or 13 hours (1600 mAh) to recharge.
KR-3UF Ni-Cd batteries take approximately 8 hours to
recharge.
! The power lamp remains lit even after charging is
●
completed.
! Shorter charging times can be achieved using the Ni●
MH/Battery Charger BCH-NH (➡P.103).
1
! Do not apply excessive force to the battery cover.
●
! Always switch the camera off when replacing the
●
17
LOADING AND REMOVING THE SmartMedia™
SELECTING THE POWER SUPPLY
4
➀
●
➁
●
Using the AC Power Adapter
SmartMediaTM
■ Only use 3.3V SmartMedia.
MG-4S (4MB), MG-8S (8MB), MG-16S (16MB),
MG-32S (32MB), MG-64S (64MB)
! Take
●
18
care not to drop the batteries when opening
and closing the battery cover.
! See P.107 for notes on using other power supplies.
●
To shoot or play back images without depleting
the battery charge, use the special AC Power
Adapter AC-3V(sold separately).
Check that the camera is switched off and then plug
the AC power adapter connector into the “DC IN 3V
socket” on the camera. Then plug the AC power
adapter into the power outlet.
! You cannot charge the batteries by connecting the AC
●
power adapter.
! The socket-outlet shall installed near the equipment and
●
shall be easily accessible.
! The shapes of the plug and socket-outlet depends on the
●
country of use.
! Using AC power adapters other than the AC-3V could
●
damage the camera.
! See P.109 for more information on the AC power adapter.
●
➀
●
➂
●
➁
●
DC IN 3V Socket
➀ Install the batteries with the correct polarity as
shown.
➁ Close the battery cover as indicated by the
arrow.
Loading the SmartMediaTM
1
➀ Check that the camera is switched off, release
the slot cover lock and open the cover.
the SmartMedia firmly into the
SmartMedia slot as far as it will go.
➂ Close the slot cover.
➁ Push
! Images
●
cannot be recorded or erased if a writeprotect sticker is affixed to the SmartMedia.
! Operation of this camera is only guaranteed when it
●
is used with Fujifilm SmartMedia.
! Some 3.3V SmartMedia are labelled as “3V ” cards.
●
! See P.110 for more information on SmartMedia.
●
! If
●
you open the slot cover while the camera is
switched on, the camera is automatically switched
off to protect the SmartMedia.
! The SmartMedia will not slide fully into the slot if it is
●
inserted facing the wrong way. Be careful not to
apply undue force to the SmartMedia.
19
SWITCHING ON AND OFF
LOADING AND REMOVEING THE SmartMedia™
Removing the SmartMediaTM
1
➀
●
2
2
➁
●
➀ Check
that the indicator in the viewfinder is
green and then switch the camera off.
➁ Release the SmartMedia cover lock as shown
in the figure.
20
1
Never open the SmartMedia slot cover while
the camera is switched on.This could destroy
the image data or damage the SmartMedia
itself.
LCD Panel
LCD Monitor
On
Push the SmartMedia into the slot slightly and
allow it to pop back out. It can then be pulled out
easily.
Press the Power button to switch the camera on
or off. When the camera is switched on, the
viewfinder lamp glows green.
! If you switch the camera on when the Mode switch is
●
set to “ 0 ”, the lens cover opens and the lens
moves out. For this reason, take care to avoid
touching the lens when you switch the camera on.
! Switch the camera on before attempting to use the
●
camera in any way.
! To
●
protect the SmartMedia, always store it in the
special anti-static case.
! See P.80, 100 for information on printing images.
●
! See P.100-102 for information on downloading
●
images to a personal computer.
When the Auto Power Off function is
enabled (➡ P.92), the camera automatically
switches itself off if it is left on and unused
for a few minutes.
Blank
Flashing
On
On
On
Check the battery level warning when you switch
the camera on.
➀The battery is fully charged.
(This icon is only displayed on the LCD panel
for 3 seconds after you switch the camera on.)
➁The battery charge is too low. Fully charged
batteries should be installed as the power will
run out shortly.
➂There is no charge at all in the batteries. The
icon disappears immediately and camera
operation stops. Install fully charged batteries.
! If
●
the date or time shown on the LCD monitor is
blinking, set the date and time. (➡ P.22)
1
21
SETTING THE DATE AND TIME
1
➀
●
➁
●
2
3
➁
●
the Mode switch to “ 0 ” ➁ Set the
Photography Mode dial to“ 2 ”.The SET–UP
screen appears on the LCD monitor.
➀ Set
! See
●
22
P.92 for more information on the items in the
“ 2”(SET–UP) mode menu.
! If the AC power adapter has been connected or the
●
batteries have been installed for about half a day or
longer, the date and time settings will be retained for
about half a day after the AC power adapter has
been disconnected or the batteries have been
removed.
➀Press
4
➀
●
“ b ” on the 4-direction button to select
“DATE/TIME”. ➁Press the “MENU/EXE” button.
Press “ d ” or “ c ” on the 4-direction button to
select the setting (year, month, day, hour or
minute), and use “ a ” and “ b ” to correct the
setting.
! Seconds cannot be specified.
●
! When the displayed time passes
●
“12:00:00”, the
camera automatically switches between AM and PM.
! PAL model : 2000 .01.01.
●
When you have finished setting the date and
time, press the “MENU/EXE” button to confirm
the setting. The SET–UP screen then reappears.
To exit the “ 2 ” (SET-UP) mode, set the
Photography mode dial to any mode other than
the “ 2” mode.
! To
●
set the time precisely, press the “MENU/EXE”
button when the time is at zero seconds.
1
23
Photography
2 Basic
1
➀
●
TAKING PICTURES (AUTO MODE)
➁
●
the Mode switch to “ 0 ” ➁ Set the
Photography Mode dial to “ 3 ”.
To take pictures using the LCD monitor, press
the “ DISP” button to switch the LCD monitor on.
2
3
4
Be careful to ensure that the lens, microphone
and flash control sensor are not obscured by
your hands or the camera strap.
➀ Set
Loop the strap over your wrist, brace your
elbows firmly against your body and hold the
camera with both hands.
2
To zoom in on your subject (
TELE), press
“a” on the 4-direction button. To zoom out (
WIDE), press “ b ”.
! Check that the lens is clean. If it is dirty, clean the
●
! If
●
24
the date/time display on the LCD monitor is
flashing, set the date and time (➡P.22).
! You can photograph subjects at distances of 80 cm
●
(2.6 ft.) to infinity. For subjects closer than 80 cm,
use Macro photography (➡P.63).
lens as described on P.106.
! The image will be blurred if the camera moves when
●
! The lens on the FinePix4700 ZOOM is a 3✕ zoom
●
you take the picture (camera shake).
! When you are shooting in low-light conditions, use
●
the flash (➡ P.59) or a tripod to prevent blurred
images due to camera shake.
lens with a focal range equivalent to 36-108mm on a
35mm camera.
When you switch the camera on, the focal length is
equivalant to 55mm.
! The
●
camera may not be able to take successful
pictures if your fingers or the strap are in the way.
25
TAKING PICTURES (AUTO MODE)
5
6
7
8
AF frame
LCD monitor
AF frame
When you are using the viewfinder to take a
picture at a distance of 0.8 to 1.5 meters (2.6 to
4.8 ft.), only the shaded area in the figure is
photographed.
Using the viewfinder or LCD monitor, frame your
shot so that the subject fills the entire AF (Auto
Focus) frame.
! When
●
! If your subject is not in the center of the picture, use
●
AF lock to take the picture(➡P.30).
26
see in the LCD monitor, you should use the viewfinder.
! If
●
Press the shutter button down half way. The
image is focused when the AF frame on the LCD
monitor becomes smaller and the shutter speed
and aperture setting appear (and the green
viewfinder lamp stops blinking and remains lit).
Viewfinder
! For dimly lit scenes where the subject is difficult to
●
To take the picture, press the shutter button
down fully without lifting your finger off it. The
camera beeps and takes the picture, and the
data is then recorded.
! If the image on the LCD monitor is difficult to see,
●
adjust the monitor brightness.
you press the shutter button down halfway,
the video image on the LCD monitor freezes briefly.
However, this is not the image that is recorded.
! If it is too dark for the camera to focus, move at least
●
1.5 m (4.8 ft.) away from your subject before taking
the picture.
you press the shutter button down fully in one
motion, the shot is taken without the AF frame
changing.
! When you take a picture, the viewfinder lamp lights
●
orange (camera not ready) before switching back to
green to indicate that the camera is again ready for
shooting.
! The viewfinder lamp flashes orange while the flash is
●
charging.
! Since the amount of image data recorded is not fixed
●
and varies depending on the subject (level of image
detail, etc.), the number of available shots may not
decrease after the image is recorded, or may
decrease by 2.
! See P.112 for information on the warning displays.
●
2
27
TAKING PICTURES (AUTO MODE)
◆Viewfinder Lamp Display
Color
Status
Lit
Green
Ready to shoot
AF/AE in progress or camera shake
Flashing warning.Recording to SmartMedia
(the next picture can be taken)
Lit
Orange
Meaning
Image being recorded onto the
SmartMedia (the next picture
cannot be taken)
Flashing Flash charging
● SmartMedia
Red
28
warning
No SmartMedia loaded,
SmartMedia not formatted,
incorrect format, write-protect
sticker used, SmartMedia full,
SmartMedia error
Flashing ●
Battery charging error
● Lens operation error
✽ When the LCD monitor is
switched on, details of the
warning are displayed on the
monitor (➡P.112).
◆Subjects Not Suitable for Autofocus◆
For still image photography (3 , 7 , 6 , 8 ,
4 , 5 ), the number of available shots is
displayed on the LCD panel in the position
shown in the figure at left.
Number of Available Frames
Though the FinePix4700 ZOOM uses an
accurate autofocus mechanism, it may
have difficulty focusing or not be able to
focus at all for the types of subject and
situation listed below. In such cases, the
image may be out of focus.
! See
●
P.94 for information on changing the Quality
setting.
! See P.95 for information on changing the File size
●
setting.
! At shipment, the default settings are NORMAL (for
●
Quality) and 2400 ✕ 1800 (for File Size).
Available frames display
● Very
shiny subjects such as a mirror or
car body.
● Subjects photographed through glass.
● Subjects that do not reflect well, such as
hair or fur.
● Subjects with no substance, such as
smoke or flames.
● When the subject is distant and dark.
● When there is very little contrast between
the subject and the background (such as
white walls or subjects dressed in the
same color as the background).
● When there are objects in front of or
behind the subject (such as an animal in a
cage or a person in front of a tree).
● Subjects moving at high speed.
◆Standard number of shots per SmartMedia
The number of shots that can be recorded onto a SmartMedia card varies slightly depending on the type of subject.
Also, the difference between the standard number of shots and the actual number of available shots increases for
SmartMedia with a higher capacity.
2400✕1800
File Size
1280✕960
640✕480
Quality Mode
FINE
NORMAL
BASIC
FINE
NORMAL
BASIC
FINE
NORMAL
BASIC
Image Data Size
APPROX.
1700KB
APPROX.
803KB
APPROX.
328KB
APPROX.
612KB
APPROX.
312KB
APPROX.
162KB
APPROX.
162KB
APPROX.
87KB
APPROX.
50KB
2
4
9
18
36
4
9
19
38
77
11
23
47
94
189
6
12
25
50
101
12
24
49
99
198
23
47
90
180
362
23
47
90
180
362
44
89
165
331
663
70
141
248
498
996
MG-4S(4MB)
MG-8S(8MB)
MG-16S(16MB)
MG-32S(32MB)
MG-64S(64MB)
2
29
USING AF/AE LOCK
1
2
In a shot with this type of composition, the
subjects (two people in this case) are not in the
AF frame. If the shot is taken at this point, the
subjects will not be in focus.
4
Move the camera slightly so that one of the
subjects in the AF frame.
! The displayed screens are those shown on the LCD
●
monitor.
! See P.24 for information on taking pictures using the
●
LCD monitor.
◆AF (AUTOFOCUS) /AE (AUTOEXPOSURE) LOCK◆
30
3
On the FinePix4700 ZOOM, pressing the shutter button down half way locks the focus and
exposure settings (AF and AE lock). If you want to focus on a subject that is not centered in the
frame or change the picture composition after the exposure is set, you can obtain good results by
changing the composition after the AF and AE settings are locked.
2
Keep the shutter button held down half way (AF
and AE locked) and check that the AF frame is
smaller and that the shutter speed and aperture
settings are displayed (and that the green
viewfinder lamp has stopped blinking and
remains lit).
With the shutter button still held down halfway
(AF lock), move the camera back to the original
image and press the shutter button down fully.
! You can reapply the AF/AE lock as many times as
●
you like before releasing the shutter.
! The AF/AE lock operates in all photography modes
●
and can be used to ensure excellent results.
31
FRAMING GUIDELINE FUNCTION
1
2
➀
●
➁
●
LCD monitor OFF
Scene
LCD monitor ON
Group shot
Framing Guideline displayed
Portrait
Scene
Group Shot
Use this frame when you want
to position your main subject in
center of the frame or when you
want to align your shot with the
horizon.
This is the most effective frame
for monitoring the size and
balance of your subject when
the shot involves motion.
Use this frame when you are
shooting groups of 2 or more
people.
By composing the shot so that
your subjects are as large as
possible within the frame, the
photograph will clearly show
their facial expressions.
Portrait
(Vertical shot frame)
Use this frame for portrait
photography.
Fit the subject's face into one of
the 3 frames to shoot a close-up
portrait (large frame), a head and
shoulders shot (middle frame), or
a half-body shot (small frame).
2
During shooting, when the Photography Mode
dial is set to “3”, “7”, “6” or “8”, the display
on the LCD monitor changes each time you
press the “DISP” button. Press the “DISP button
to display the “Framing Guideline”.
◆ List of Photography Modes/Framing Guideline
32
3
Scene • Group Shot • Portrait
7
Portrait frames only (3 types)
6
Scene • Group Shot
8
Scene • Group Shot
➀You can select an framing guideline by holding
down the “SHIFT/r” button ➁and pressing “a”
on the 4-direction button. The selected framing
guideline serves as a guide to composing your
shot when you are taking pictures using the LCD
monitor.
! The framing guideline is not recorded on the image.
●
! Press the “SHIFT/r” button to view the Camera
●
Operation Guide (an explanation of the operations
available when you press the “SHIFT/r” button).
! The
●
lines in the scene frame roughly
divide the recorded pixels into three equal
parts horizontally and vertically. When the
image is printed, the resulting print may be
shifted slightly from the scene frame.
◆Important◆
Always use the AF/AE lock to compose your picture.
Failing to use the AF/AE lock may result in the image
being out of focus.
33
VIEWING YOUR IMAGES (PLAYBACK)
1
FAST FORWARDING IMAGES
➀
●
2
1
2
➁
●
Normal playback
No text displayed
Set the mode switch to “ 1 ”.
Multi-frame playback
! When
●
you set the mode switch to “ 1 ”, the last
image shot is displayed.
! If image on the LCD monitor is difficult to see, adjust
●
the LCD monitor brightness (➡P.99).
! If you press the “DISP” button once, the text
●
displayed on the LCD monitor disappears.
You can fast forward through the frames by
holding down “ d ” or “ c ” on the 4-direction
button for about 3 seconds during playback.
During fast forward, 3 frames are shown
together in miniature on the LCD monitor. When
you stop fast forward, the image enclosed in the
frame is displayed on the monitor as a single
image.
2
You can use “ c ” and “ d ” on the 4-direction
button to move forward and backward
respectively through your images.
The LCD monitor display changes each time you
press the “DISP” button.
◆Images That Can be Viewed on the FinePix4700 ZOOM◆
34
You can use this camera to view images recorded on an FinePix4700 ZOOM or images recorded
onto a 3.3V SmartMedia using a Fujifilm MX series and DX series digital camera.
! A progress bar is displayed to show the approximate
●
playback position on the SmartMedia.
35
PLAYBACK ZOOM
1
MULTI-FRAME PLAYBACK
2
➁
●
➀
●
1
➀
●
➂
●
➁
●
“ d ” or “ c ” during zooming cancels
zooming and moves to the next image.
➀
●
2
➀ Press the “DISP” button twice during playback.
➁ The 9-shot multi-frame playback screen
Pressing “a” and “ b ” on the 4-direction button
during playback zooms in and out on (enlarges
and reduces) the still image respectively. When
you use this function, a zoom bar is displayed.
●Zoom scales:2400✕1800-dot images: Max15✕
1280✕ 960-dot images: Max 8✕
640✕ 480-dot images: Max 4✕
! Pressing
●
➁
●
If you have taken more than 9 pictures, ➀ you
can quickly skip to the next page of images by
holding down the “SHIFT/r” button, ➁ and
pressing “d”or “ c” on the 4-direction button.
After you have zoomed an image, ➀ you can
move around the image by holding down the
“SHIFT/r” button, ➁ and pressing “a”, “ b ”, “d”
and “ c” on the 4-direction button.
36
2
appears.
“d ” or “ c ” on the 4-direction button to
select a frame. To view the selected frame as a
full-size image, press the “DISP” button again.
➂ Press
! The
●
! Press
●
the “CANCEL / BACK” button to return to
normal unscaled display.
LCD monitor text display disappears after
approximately 3 seconds.
! Playback zoom cannot be used with multi-frame
●
playback.
! The “a” and “ b ” buttons are disabled during multi●
frame playback.
the “SHIFT/r” button displays the onscreen SHIFT CONTROL.
! Multi-frame playback is particularly useful for
●
selecting images for single-frame erase, singleframe protect, Resize, DPOF frame specification or
DPOF confirmation and cancellation.
! Pressing
●
37
ERASING SINGLE FRAME
1
➀
●
➁
●
2
3
4
Press the “MENU/EXE” button to erase the
displayed image. When erasing is complete, the
next image appears and the “ERASE OK?”
message is displayed.
➀ Set the mode switch to “ 1”, ➁ and press the
“MENU/EXE” button to display the Menu screen
on the LCD monitor.
! See
●
38
P.71 for more information on the Playback
mode menu.
! Multi-frame playback is an easy way to select
●
images to be protected.
“c” Select “FRAME” in the ERASE menu and
press the “MENU/EXE” button.
2
Press “d ” or “ c ” on the 4-direction button to
display the image to be erased.
! To
●
! To
●
cancel single-frame erase, press the
“CANCEL/BACK” button to return to the menu. To
exit the menu screen, press the “CANCEL/BACK”
button again.
continue erasing images, repeat the procedure
from step 3 .
! If “ P R O T E C T E D F R A M E ” is displayed, the image
●
protection must be removed to erase the image
(➡P.76).
! If the “
” message is displayed, DPOF
●
is specified. When you press the “MENU/EXE”
button, the image is erased and the DPOF settings
are updated.
DPOF SPECIFIED.
ERASE OK?
39
Features
3 Advanced
USING A TV MONITOR
1
The Advanced Photography section introduces a range of camera functions that you can access by setting the Mode
switch to “0 ”.
2
◆ Photography mode specifications
A/V OUT socket
Video (yellow)
To terminals
Audio (white)
Switch off the camera and TV. Plug the A/V
cable (accessory) into the A/V OUT (audio-visual
output) socket on the camera.
Plug the other end of the cable into the
audio/video input socket on the TV. Then switch
the camera and TV on and take pictures or play
back images as you would normally.
PhotoGraphy
Mode
3
Auto
(➡P.24· 42)
7 Portrait
(➡P.42)
6 Landscape
(➡P.42)
8Night Scene
(➡P.43)
4 Manual
(➡P.44)
! If you connect the A/V cable during playback, you
●
will not hear the sound from the TV.
! If you disconnect or reconnect the A/V cable while
●
40
the power is switched on, the sound may not be
output correctly.
! If there is a power outlet available, connect the
●
AC-3V AC Power Adapter.
ADVANCED FEATURES PHOTOGRAPHY
Accessible menu settings
Factory default
Flash
Photography
(➡P.59)
Macro
photography
(➡P.63)
Self-Timer
Photography
(➡P.64)
-----------------------
------------
O
O
O
-----------------------
------------
O
✕
O
-----------------------
------------
✕
✕
O
Setting the Manual Focus
(➡P.54)
OFF
O
✕
O
Setting the Brightness
Flash Brightness Adjustment
Setting the White Balance
Setting the Sensitivity
Setting the Manual Focus
Metering Mode
Sharpness
Preview Display
(➡P.51)
(➡P.52)
(➡P.52)
(➡P.53)
(➡P.54)
(➡P.55)
(➡P.56)
(➡P.57)
0
0
AUTO
200
OFF
MULTI
0
ON
O
O
O
(➡P.54)
(➡P.58)
OFF
OFF
✕
O
O
------------
✕
✕
✕
5 C o n t i n u o u s Setting the Manual Focus
! If your TV has stereo audio input sockets, plug the
●
cable into the left (white) socket.
! Refer to the instructions provided with your TV for
●
more information on audio and A/V input for your TV.
Shooting
(➡P.45)
9 Movie
(➡P.47)
Auto Bracketing
-----------------------
3
41
PHOTOGRAPHY MODE
AUTO 7 PORTRAIT 6 LANDSCAPE
PHOTOGRAPHY MODE
8 NIGHT SCENE
3 Auto
This is the simplest mode to use and has a wide
range of applications. (➡ P.24)
7 Portrait
This mode is for shots of people. It shows skin
tones beautifully and gives a softer image.
! Macro photography cannot be used in this mode.
●
You can select from 7 photography modes to
suit the type of shot. Select the mode by turning
the Photography Mode dial.
The “7” (Portrait), “6” (Landscape) and “8”
(Night Scene) modes are tailored to particular
types of scene.
6 Landscape
This mode is for shots of scenery during the day.
It gives clear, sharp images of scenery such as
buildings and mountains.
● White balance
The setting used is for outdoor lighting.
● Flash
The flash will automatically be disabled and
cannot be enabled manually.
! Macro photography cannot be used in this mode.
●
42
8 Night Scene
The best mode for shots taken in the evening or
at night. This mode tends to use slower shutter
speeds than Auto mode photography.
● Shutter speed
This is a slow shutter mode with a maximum
time of 3 seconds.
● White balance
The setting used is for outdoor lighting.
● Flash
Forced Flash, red-eye reduction only.
! Because a slow shutter speed is used, a tripod should
●
be used to prevent camera shake.
! Macro photography cannot be used in this mode.
●
When you press the flash pop-up button to use
the flash for clear and detailed shots of people
against a night or evening background, this
mode makes it possible to use the flash with a
slow shutter speed (slow-synchro).
3
! If you do not want to use the flash, press the flash
●
back down to close it.
P.59-62 for more information on flash
photography.
! See
●
43
PHOTOGRAPHY MODE
MANUAL
1
PHOTOGRAPHY MODE
2
CONTINUOUS SHOOTING
1
5 Continuous Shooting
This mode allows you to shoot up to 3
consecutive frames at intervals as short as 0.2
seconds.
4 Manual
Manual mode allows you to take pictures using a
particular set of desired menu settings.
44
! See
●
P.50-58 for more information on the function
settings (photography menu settings).
If you take a picture using the factory default
settings, a preview screen (showing the
photographed image) is displayed on the LCD
monitor. To record the image, press the
“MENU/EXE” button. To discard the image
without recording it, press the “CANCEL/BACK”
button.
! The factory default settings for Manual mode are the
●
same as those for Auto mode except for the preview
screen display.
! See
●
P.54 and 58 for more information on manual
focus and auto bracketing.
! You cannot use the flash in this mode.
●
! The continuous photography speed is the same
●
regardless of the quality and file size settings.
2
When you press the shutter button down
halfway (so that the green viewfinder lamp stops
flashing and stays lit), focusing is completed.
The shot is taken when you press the shutter
button down fully.
3
! The focus and exposure are set when the first frame
●
is shot and do not change for the subsequent
frames.
! The first recorded picture will be displayed in LCD
●
monitor during the continuous shooting.
45
PHOTOGRAPHY MODE
CONTINUOUS SHOOTING
3
4
A
PHOTOGRAPHY MODE
9 MOVIE
1
2
C
B
After the shooting is done, the preview pictures
will be displayed on the monitor in the order that
they are shot, A is first, B is second, C is third.
9 Movie
To record the images, press the “MENU/EXE”
button. The “STORING” message appears on
the LCD monitor while the images are being
recorded onto the SmartMedia. If you do not
want to record the images, press the
“CANCEL/BACK” button.
46
! If you release the shutter button quickly, fewer than 3
●
frames may be shot.
! It takes about 11 seconds to record the 3 frames of
●
image data (NORMAL : 2400 ✕ 1800 pixels).
In this mode, you can shoot up to 80 seconds of
movie with sound at a time (Motion JPEG format
(➡ P.105) at 320 ✕ 240 pixels and 10 frames per
second).
! Because the audio is recorded as you shoot, take
●
care not to cover the microphone with your finger
(➡ P.8).
! Depending on the space available on the
●
SmartMedia, the time that can be recorded in one
movie may be shorter than 80 seconds.
! You cannot switch the LCD monitor off in this mode.
●
When you select movie, the available recording
time is displayed on the LCD panel.
When “STANDBY” then appears on the LCD
monitor, the camera is ready to shoot.
3
◆SmartMedia standard shooting time
SmartMedia
capacity
MG-4S
(4MB)
MG-8S
(8MB)
MG-16S
(16MB)
MG-32S
(32MB)
MG-64S
(64MB)
Available
recording time Approx.22 Approx.45 Approx.90 Approx.182 Approx.364
(sec.)
47
PHOTOGRAPHY MODE
9 MOVIE
3
4
Shooting begins when you press the shutter
button down fully.
In movie photography, the lens is fixed at the
wide-angle setting. Only digital zooming can be
used. The “a” and “ b ” keys on the 4-direction
button control the digital zoom. A zoom bar is
shown on the LCD monitor.
In the top right cornet of the LCD screen is the
bar showing the time remaining for recording.
48
5
6
A "recording time bar" is displayed on the LCD
monitor during shooting.
If you press the shutter button down fully during
shooting, shooting stops and the movie is
recorded onto the SmartMedia.
3
! While
●
shooting a movie, there will not be a beep
sound even if the shutter button is pressed.
! You do not need to hold down the shutter button.
●
! The focus is fixed at 80 cm (2.6 ft.) to infinity.
●
! The focus and white balance are fixed during
●
shooting, but the exposure varies automatically to
suit the scene being shot.
! The “recording time bar” is displayed as a guide to
●
the amount of remaining recording time.When the
recording time bar reaches the right-hand end,
recording automatically ends and the data is
recorded onto the SmartMedia.
! It
●
takes about 11 seconds to record an 80-second
movie (roughly 12 MB) onto a SmartMedia.
! Even if you stop shooting immediately after it has
●
begun, roughly 3 seconds of movie will be recorded.
49
PHOTOGRAPHY MENU
PHOTOGRAPHY MENU
➀,●
➃
●
1
SETTING THE BRIGHTNESS (EXPOSURE COMPENSATION)
◆Subjects for Which Exposure
Adjustment is Particularly Effective◆
2
Positive (+) Compensation
● Copying
➁
●
➂
●
To move to another menu page, press “d ” or
“ c ” on the 4-direction button for the arrows in
the menu (“ ” or “ ”)
➀Press
the “ MENU/EXE” button to display the
menu on the LCD monitor.
➁Use “d” and “ c ” on the 4-direction button to
select the menu setting.
➂Use “a” and “ b ” on the 4-direction button to
change the setting.
➃Press the “ MENU/EXE” button to confirm the
setting.
50
! The available menu settings vary depending on the
●
photography mode. (➡ P.41)
You can set the brightness when the
photography mode is set to “ 4”.
Use the Brightness setting to obtain the optimum
image brightness (exposure) when the subject is
much brighter or darker than the background.
● There
are 11 compensation levels (–1.5 to 1.5
EV in approx. 0.3 EV increments). See P.105
for a definition of EV.
! The
●
Brightness setting is disabled in the following
situations:
·When the flash is used in Auto or Red-eye
Reduction mode
·When dark scenes are shot in Forced Flash mode
of printed text (black characters
on white paper) (+1.5 EV)
● Backlit portraits (+0.6 to +1.5 EV)
● Very bright scenes (such as snowfields)
and highly reflective subjects (+0.9 EV)
● Shots made up predominantly of sky.
(+0.9 EV)
Negative (–) Compensation
● Spotlit
subjects, particularly against dark
backgrounds (–0.6 EV)
● Copying of printed text (white characters
on black paper) (–0.6 EV)
● Scenes with low reflectivity, such as
shots of pine trees or dark foliage (–0.6
EV)
3
✽ Settings given in parentheses are a general
guide.
51
PHOTOGRAPHY MENU
PHOTOGRAPHY MENU
MFLASH BRIGHTNESS ADJUSTMENT
PHOTOGRAPHY MENU
SETTING THE WHITE BALANCE
SETTING THE SENSITIVITY
AUTO : Automatic adjustment
(Shooting to show the ambience of the
light source)
You can set the flash brightness when the
photography mode is set to “ 4”.
Set the Flash Power setting to achieve the
optimum flash brightness when the subject in
the picture is very small or when you are using
close-up flash photography.
● There
are ±2 correction levels (–0.6 to +0.6 in
approx. 0.3 EV increments). See P.105 for a
definition of EV.
You can set the white balance when the
photography mode is set to “ 4”.
Change the white balance setting when you
want to take a picture with the white balance
fixed for the surroundings and lighting when the
picture is taken.
In Auto mode, the correct white balance may not
be obtained for subjects such as close-ups of
people's faces and shots taken under a special
light source. In such situations, select the correct
white balance for the light source. See P.105 for
more information on the white balance.
g
: Shooting outdoors in fine weather
f
: Shooting in shade
l
: Shooting under “Daylight” fluorescent
lamps
m
: Shooting under “Warm White” fluorescent
lamps
n
: Shooting under “Cool White” fluorescent
lamps
q
: Shooting in incandescent light
✽ The white balance setting is ignored when the flash is
used. To achieve the desired effect in your shot,
press the flash back down to suppress flash
operation. (➡P.62)
You can set the sensitivity (film speed) when the
photography mode is set to “4”.
Use this setting when you want to take bright
pictures indoors without using a flash or when
you want to use a fast shutter speed (to prevent
camera shake, etc.).
● Settings:
200 (standard setting), 400, 800
3
! To
●
52
take the picture immediately, press the
“MENU/EXE” button to confirm the white balance
setting.
53
PHOTOGRAPHY MENU
SETTING THE MANUAL FOCUS
1
54
h PHOTOMETRY
◆The light metering modes are
effective for the following subjects◆
2
Press “ d ” on the 4-direction button to move the
focus closer ( ) and “ c ” to move the focus
further ( )away. To check focusing, please use
the LCD monitor.
You can select manual focus when the
photography mode is set to “ 8”, “ 4” or “ 5”.
Use manual focus when the AF function does
not focus the camera or for subjects that are not
suited to AF (➡ P.28).
When manual focusing is set to ON, the “ C”
icon appears on the LCD monitor.
PHOTOGRAPHY MENU
! Because
●
the macro and flash settings cannot be
changed once manual focus is set to ON, set the
macro (➡ P.63) and flash (➡ P.59) settings
beforehand.
You can set the metering when the photography
mode is set to “ 4”.
Use this mode for scenes where the brightness
of the subject and background differ markedly so
that the Multi setting is unlikely to achieve the
desired result.
● AVERAGE: Light metering where an average
value for the entire image is used.
● SPOT
: Light metering where the exposure
is optimized for the center of the
image.
● MULTI
: Light metering where the camera
automatically assesses the scene
and selects the optimum
exposure.
! In "AUTO" mode, the light metering is set to Multi.
●
● AVERAGED
The advantage of this mode is that the
exposure tends not to change for
different compositions or subjects. This
mode is particularly effective for shots of
people wearing black or white clothing
and shots of scenery.
● SPOT
This mode is useful for subjects with
strongly contrasting light and dark areas
where you want to achieve the correct
exposure for a particular feature.
● MULTI
This mode uses automatic scene
recognition to analyze the subject and
obtain the optimum exposure in any
conditions. The "Multi" setting should
normally be used.
3
55
PHOTOGRAPHY MENU
SHARPNESS
You can set the sharpness when the
photography mode is set to “ 4”.
Use this setting to soften or emphasize outlines
or to adjust the image quality.
● The sharpness can be set to ±1 level.
PHOTOGRAPHY MENU
Three levels of sharpness are available.
+ :Emphasizes the outlines.
Best for shots of subjects such as buildings
or text where you want sharp images.
0 :Best for ordinary photography.
Provides edge sharpness that is ideal for
ordinary shots.
--- :Softens the outlines.
Best for shots of subjects such as people,
where a softer image is desirable.
PREVIEW DISPLAY
➀
●
➁
●
You can set the preview display when the
photography mode is set to “ 4”.
Use this setting to specify whether a preview
screen (showing the photographed image) is
displayed after you take a photograph.
ON: The preview screen is displayed and you
can choose whether to record the image.
OFF: The preview screen is not displayed and
the image is automatically recorded.
56
By magnifying the preview picture, checking of
the focusing and details of the picture is
possible.
➀ You can zoom in or out on the image on the
preview screen by pressing “a” or “ b ” on the
4-direction button.
➁ You can move around a zoomed image by
holding down the “ SHIFT/r ” button and
pressing “ d ”, “ c ”, “ a ” or “ b ” on the 4direction button.
3
57
PHOTOGRAPHY MENU
AUTO BRACKETING
FLASH PHOTOGRAPHY
1
A
2
C
B
Auto Bracketing can only be specified when the
photography mode is set to “ 5 ”. Use this
feature to photograph the same image with
different exposure settings. This feature
automatically takes three consecutive pictures
with under, normal, and over exposure. The
amount of the under and over exposure is abe to
be preset.
When you take the picture, the preview screen
appears. A is the overexposed image, B is the
normal image, and C is the underexposed
image. To record the images, press the
“MENU/EXE” button. To discard the images
without recording them, press the “CANCEL
/BACK” button.
● The
three available settings are ±1/3, ±2/3 and
±1 EV.
58
is insufficient space on the SmartMedia for 3 shots,
no picture will be taken.
●
Effective flash range
Wide-angle : 0.2 to 4 m (0.7 ft. to 13.1 ft.)
Telephoto : 0.2 to 3 m (0.7 ft. to 9.8 ft.)
Press “ c ”on the 4-direction button to select the
flash setting. The setting cycles sequentially
through the following: x ➡ Z ➡ v ➡ w
3
! In Auto mode, always pop the flash up and use the
●
automatic flash.
! The
●
! This feature always takes 3 shots. However, if there
●
Press the flash pop-up button to set the flash.
"STORING" message appears on the LCD
monitor while the images are being recorded onto
the SmartMedia.
! It takes about 11 seconds to record the image data
●
(NORMAL: 2400 ✕ 1800 pixels).
! When you pop the flash up, the image shown on the
●
screen may disappear and the screen may go dark
because the flash is charging. In this event, the
viewfinder flashes orange.
! If you do not want to use the flash, press the flash
●
back down to close it.
! If manual focus is set to ON or the flash unit is closed,
●
the flash setting cannot be changed. Set manual focus
to OFF (➡P.54) and pop up the flash.
59
FLASH PHOTOGRAPHY
x Auto flash mode
Use this mode for ordinary photography. The
flash fires automatically as required by the
shooting conditions.
◆Red-Eye Effect◆
60
Z Red-Eye Reduction
Use this mode to ensure that the subject's eyes
appear natural when photographing people in
low-light conditions.
The flash fires a pre-flash just before the picture
is taken and then fires again to take the actual
picture.
When you use the flash to photograph people in low-light conditions, their eyes sometimes appear
red in the picture. This is caused by the light of the flash reflecting off the inside of the eye. Use
Red-Eye Reduction flash mode to effectively minimize the likelihood of the red-eye effect.
Take the following measures also to make Red-Eye Reduction mode more effective:
● Get the subjects to look at the camera.
● Get as close as possible to the subjects.
v Forced Flash
Use this flash mode to photograph backlit
scenes, such as a subject against a window or
in the shade of a tree, or to obtain the correct
colors when you are shooting under lighting
such as fluorescent tubes. In this mode, the
flash fires in bright as well as dark conditions.
w Night Scenes (Slow Synchro)
This is a flash mode that uses a slow shutter speed.
This allows you to take pictures of people at night
that clearly show both your subjects and the
nighttime backdrop.
3
! Because a slow shutter speed is used, a tripod should
●
be used to prevent camera shake.
To take the picture with a background brightly
with a main subject in the night, please use the
“8 ” (Night Scene) photography mode
settings.(➡P.43).
61