Tiling systems for industrial and residential buildings.

Transcription

Industrie_Objektbau IRL.qxd:Layout 5
19.10.2010
10:45 Uhr
Seite 1
Industrial and residential buildings.
Tiling systems for industrial
and residential buildings.
Specialist systems for professionals by professionals.
Building materials for professionals
2
19.10.2010
10:45 Uhr
Seite 2
www.botament.co/uk
19.10.2010
10:45 Uhr
Seite 3
Specialist systems for professionals by professionals.
Table of contents
Introduction
Bonded waterproofing
Tiling in residential buildings
Swimming pools
4-5
6-7
8
8 - 15
Industrial kitchens
16 - 19
Laboratories – conductive floor coverings
20 - 23
Food & drinks areas / cold stores
24 - 29
Industrial kitchens
Factories – conventional mortar bed
32
40 - 41
Tiling in wet rooms
30
Public showers
30 - 33
Wellness areas
34 - 35
Car wash plants
36 - 39
Product overview
42 - 49
Tables
50 - 53
Service
54 - 55
3
19.10.2010
10:45 Uhr
Seite 4
Introduction
Floors for industry and commerce
– only for professionals
Industrial and commercial floors
are subject to a wide range of different uses and above all – to extremely high loadings.
Moisture, organic liquids, acids,
oils, cleaning agents or bacteria
attack coverings in slaughter houses, industrial kitchens, car wash
facilities, swimming pools or garages and cause damage. The consequence is expensive repairs.
Over the past decades reaction
resin mortars on epoxy resin basis
were specified by planners and
were used on many industrial and
commercial surfaces that were
subject to heavy loads and high
mechanical use.
Epoxy resins are beneficial in
areas with mechanical stresses
due to their diverse chemical resi-
4
stance, high mechanical strength
and low abrasion. However,
epoxy resins tend to show weaknesses when subjected to hot
water, organic acids or oxidants.
Another weak point of epoxy resins is at the same time every
swimming pool operator’s nightmare:
Microbiological growth, which
causes mould formation at overflow gutters and underwater
lights.
Epoxy resin still hasn’t shaken off
the worry of it potentially harbouring health hazards; the processing of epoxy resin also
requires more diligence and takes
longer compared with standard
cement joints.
Lately, Botament® has launched
two products for these problem
areas, BOTON® EF 500 and
BOTON® EK 500, that have been
tested and approved in accordance with the latest KTW/KSW
Certification 2008, i.e. they have
met the latest, highly demanding
test criteria in drinking water approval procedures. Coupled with
this is outstanding processability
– which is virtually unique for
epoxy resins.
The success for both products
since the market launch attests to
that. A real benefit for any professional applicator who has to
work with these materials on a
regular basis.
KSW/KTW
certificati
on
BOTON® EK 500
BOTON® EF 500
Epoxy resin adhesive
2 comp.
Epoxy resin joint grout,
2 comp.
19.10.2010
For surfaces that are less suitable
for epoxy resins, based on the limitations mentioned earlier, Botament® has been developing
minerally-inorganic silicate-based
tile adhesives and joint mortars.
These product systems are also
durable, economic and most importantly, their application is kind
to the environment.
Our product BOTON CF 200,
BOTON® S 250, BOTON® MF 300
and BOTON® SF 100 feature, depending on the respective product, higher resistances in terms
of either temperature, acids, leaches, organic liquids or oxidants.
On top of that, they have clearly
improved application characteristics compared with epoxy resins.
®
10:45 Uhr
Seite 5
Their major advantage, however,
is their high resistance against
micro-biological attack, which eliminates undesirable mould, e.g.
in food production or in swimming pools and wellness facilities,
when combined with adequate
cleaning.
Irrespective whether product systems are silicate-based or epoxy
resin-based, to produce a rather
durable and low-maintenance tile
covering the installation materials
must always be matched exactly
to the loading to be expected.
The company Botament® has
sound know-how in the development and manufacture of epoxy
resin-based products.
Botament® was also the first company to launch a minerally-inorganic system on the market after
years of painstaking research and
development efforts.
Since then this area has seen continuous expansion and improvements by way of working closely
with professional applicators all
over Europe.
Botament® Productsystems:
Building materials for
professionals
5
19.10.2010
10:45 Uhr
Seite 6
Bonded Waterproofing
Building structures and components must be built in such a way
that moisture or other chemical,
physical or biological influences
cannot pose any hazards or cause
unreasonable nuisances. This has
been regulated in all the building
regulations of the German Federal countries.
As a consequence, building structures, such as pools, showers, terraces, balconies and similar must
be protected against moisture penetration. Building components
subject to moisture load are usually fitted with tiles or slabs.
Ceramic coverings can withstand
moisture and are water-repellent,
but are not water-impermeable;
they are however water-permeable to such an extent that necessitates additional sealing.
6
Moisture loading
Bonded waterproofing with tiles
and slabs in interior and exterior
areas are defined according to socalled moisture penetration classes. Such bonded waterproofing
has proven successful in practice.
Depending on moisture load the
distinction is made between high
loads (application area regulated
by building authorities) in classes
A, B and C and moderate load
(not regulated by building authorities) in classes A0 and B0.
Bonded waterproofing against
non-pressing water at high load,
e.g. in wet rooms in public and
commercial areas, as well as
against pressing water from the
inside in interior and exterior
areas, such as in swimming pools,
are published in the Building Regulation List A, part 2 of the Deutsche Institut für Bautechnik (DIBt)
[German Institute for Construction Technology].
Building Authority Certification
The construction chemicals industry is obliged to produce a building authority certification (abP)
based on agreed test principles.
This attests that a product is fit for
the purpose of bonded waterproofing.
Products that have been so tested
are identified with the Ü-sign. By
contrast to building structure waterproofing in accordance with
DIN 18195 bonded waterproofing
of coverings made from ceramic
or natural stone do not require
any further protective layers.
This means lower installation
heights and construction thicknesses can be realized.
Another advantage of this construction method is the fact that
the substrate cannot get soaked
by hygienic and/or chemically
questionable waters.
Load classes
19.10.2010
10:45 Uhr
Loads
Seite 7
Application example
Waterproofing material
BOTACT® DF 9 Sealing membrane*
BOTACT® MD 28
Special Waterproofing Compound 2 comp.
A
Wall and floor areas subjected to
high loads from industrial water Public showers
and cleaning water
BOTON® E 170
Epoxy resin waterproofing membrane, 2 comp
BOTACT® MD 1
Flexible Waterproofing Compound
BOTACT® Sealing and Decoupling Membrane
B
Wall and floor areas in swimming pools in interior and exterior areas (with pressing water
from the inside)
C
Wall and floor areas under high
water load coupled with chemical load in interior areas
BOTACT® MD 28
Special Waterproofing Compound 2 comp.
Wall and floor areas in
swimming pools
BOTON® E 170
Wall and floor areas in areas
with limited chemical loads
BOTON® E 170
(Areas where the German Water
Resources Act is to be applied
(§ 19 WHG) are exempt)
*Only for walls.
7
19.10.2010
10:46 Uhr
Swimming pools.
SYSTEM COMPONENTS
Deep-action Primer
BOTACT® D 11
Sanitary Sealing Tape & Accessories
BOTACT® SB 78
Special Sealant, 2 comp.
BOTACT® MD 28
Superior Flexible Adhesive
BOTACT® M 21 Classic or
Flexible Fluid-Bed Grout
BOTACT® M 29
Swimming Pool Grout 2 comp.
BOTON® S 250 or
Special grout, 2 comp.
BOTON® CF 200 or
Mosaic and Swimming Pool Grout
BOTON® MF 300/S 250
Epoxy resin joint grout, 2 comp.
BOTON® EF 500
Special-joint grout, 2 comp.
BOTON® CF 600
8
Seite 8
19.10.2010
10:46 Uhr
Seite 9
5+6
4
2+3
1
Swimming pools, thermal bath, brine bath
Tiling in swimming pools
The demands on construction chemicals used in swimming pools are
very high. Mineral mortar systems
offer micro-organisms a bad breeding-ground, but have limited resistance against cleaning agents and
chemicals. BOTON® S 250 and
BOTON® MF 300 are minerally-inorganic silicate mortars.
They have high mould resistance
and are therefore particularly
suited for use in swimming pools
and wellness spas.
They
• are water vapour diffusion open
• are highly steam-jet resistant
• have drinking water approval in
accordance with DVGW W 270 and
are KTW and KSW tested
Should epoxy resin joint mortars
nevertheless be used in swimming
pools, they must be approved in accordance with the ZDB datasheet
“Swimming Pool Construction“ and
must hold valid KSW/KTW certification from the “Deutschen Gesellschaft für das Badewesen“
[German Association for Swimming
Pools].
This also includes the W 270 Test,
which gives proof that the formation of micro organisms – compared with standard trade epoxy resin
joint mortars – is not promoted
using BOTON® EF 500.
by
preparation
Background
-pressure
means of high
asted!
rays or sandbl
1
2
Priming wall and floor areas with
BOTACT® D 11.
3
Insertion of the sealing tape and
interior edge BOTACT® SB 78.
4
Application of BOTACT MD 28, a
two-layered special sealant.
®
5
Application of Flexible Superior Adhesive BOTACT® M 21 Classic or of
Flexible Fluid-Bed Mortar BOTACT®
M 29.
6
Insertion of slabs into BOTACT M
21 Classic using the combined
method.
®
Reliable jointing of the cover using
the Swimming Pool Grout BOTON®
S 250.
Performance copy and cleaning recommendations can be downloaded at www.botament.co/uk
9
10
19.10.2010
10:46 Uhr
Seite 10
19.10.2010
10:46 Uhr
Seite 11
Swimming pool details 08.01
with high water level
1. Pool bowl, see detail 08.01.01, page 12
2. Corner structure, see detail 08.01.02, page 13
3. Drains and lights, see detail 08.01.03,
4. Joint tapes in concrete structures
5. Making good of chunking using levelling mortar
BOTACEM® M 100
SYSTEM COMPONENTS
Levelling mortar
BOTACEM® M 100
Special-purpose sealing agent 2c
BOTACT® MD 28
Flexible high-performance adhesive
BOTACT® M 21 Classic
At heavy duty with
epoxy resin adhesive
BOTON® EK 500
Jointing the ceramic tiles with
Swimming Pool Grout 2c
BOTON® S 250
Mosaic with Mosaic- &
Mosaic grout 2c
BOTON® MF 300
or special-grout 2c
BOTON® CF 200
At heavy duty with
Epoxy resin grout 2c
BOTON® EF 500
Special-grout
BOTON® CF 600
11
19.10.2010
Pool bowl details
10:47 Uhr
Seite 12
08.01.01
1. Sealing tape BOTACT® SB 78 in bonded waterproofing
2. Back filling profile
3. Special flexible joint mortar BOTON® CF 600
4. Pool bowl ceramics
5. Finishing profile for the gutter cover
6. Gutter grate
7. Capillary-breaking joint seal with epoxy resin joint
mortar BOTON® EF 500
SYSTEM COMPONENTS
Levelling mortar
BOTACEM® M 100
BOTACT® MD 28
At heavy duty with
BOTON® EK 500
BOTON® S 250
Mosaic grout 2c
BOTON® MF 300
or special-grout 2c
BOTON® CF 200
At heavy duty with
BOTON® EF 500
Special-grout
BOTON® CF 600
12
19.10.2010
10:47 Uhr
Seite 13
Corner structure details 08.01.02
It is important to only install flanged drains, skimmers or pool
installations of equal quality.
1. Sealing tape BOTACT® SB 78 in bonded waterproofing
2. Backfilling profile
3. Special flexible grout BOTON® CF 600
4. Ceramics
5. Joint tape in concrete structures
6. Filling of defects with levelling mortar BOTACEM® M 100
7. Swimming pool joint BOTON® S 250
SYSTEM COMPONENTS
Levelling mortar
BOTACEM® M 100
BOTACT® MD 28
At heavy duty with
BOTON® EK 500
BOTON® S 250
Mosaic grout 2c
BOTON® MF 300
or special-grout 2c
BOTON® CF 200
At heavy duty with
BOTON® EF 500
Special-grout
BOTON® CF 600
13
19.10.2010
10:47 Uhr
Seite 14
Drains / pipe openings 08.01.03
It is important to only install flanged drains, skimmers or pool
installations of equal quality.
1. Sealing of sealing tape BOTACT® SB 78
in bonded waterproofing
3. Special flexible joint sealant BOTON® CF 600
4. Flange drain with grating
5. Flexible superior adhesive BOTACT® M 21 Classic / BOTACT® M 29
6. Swimming pool ceramics
7. Special sealant BOTACT® MD 28
14
19.10.2010
10:47 Uhr
Seite 15
SYSTEM COMPONENTS
Special Sealant, 2 comp.
BOTACT® MD 28
BOTACT® M 21 Classic or
Flexible Fluid-Bed Grout
BOTACT® M 29
BOTON® EK 500
BOTON® S 250
Mosaic grout 2c
BOTON® MF 300
or special-grout 2c
BOTON® CF 200
At heavy duty with
Epoxy resin joint grout 2c
BOTON® EF 500
BOTACEM® M 100
Special-joint grout, 2 comp.
BOTON® CF 600
15
19.10.2010
10:47 Uhr
Industrial kitchens.
SYSTEM COMPONENTS
Epoxy - resin primer 2c
BOTON® E 120
BOTACT® SB 78
Epoxy resin coating 2c
BOTON® E 170 or
BOTACT® Thin de-coupling
membrane
BOTON® EK 500
BOTON® EF 500 or
BOTON® CF 200
Flexible acid-resistant sealant
BOTON® SF 400
Seite 16
19.10.2010
10:47 Uhr
Seite 17
5+6
4
3
2
1
Project Installations
Industrial kitchens
In industrial kitchens the covering is typically subject to loading from cleaning agents and
hot water, as well as from oil
and grease.
This demands a sophisticated
floor construction, especially
with regard to tile adhesive,
joint mortar and sealant.
For a high chemical-resistant
epoxy resin waterproofing we
recommend for such areas
under heavy loads BOTON® E
170 Epoxy Resin Waterproofing.
In most cases, however, it is possible to use the BOTACT® Sealing
and
Decoupling
Membrane, which secures a
more rapid installation progress.
1
Priming of wall and floor areas with
BOTON® E 120. Substrates with large
pores: application of BOTON® E 120
as scratch coat with quartz sand.
3
Scattering in of quartz sand into
the fresh sealing layer of
BOTON® E 170.
icale chem aterh
t
o
t
w
tively
resin
Alterna
poxy ® 170 the BOe
t
n
a
N E
ng
resist
g BOTO
ecoupli
proof®in ealing and D .
S
used
TACT
can be
e
n
a
r
Memb
2
2nd application of the highly chemical-resistant
sealing
layer
BOTON® E 170 (in two layers).
4
Application of highly chemical-resistant tile adhesive BOTON® EK 500.
**Please follow our cleaning
recommendation here.
5
Inserting tiles into BOTON® EK 500.
6
Jointing of tiles with BOTON® CF
200 or BOTON® EF 500
17
19.10.2010
10:48 Uhr
Seite 18
Water proofing details 10.01.
It is important to always fit flanged drains.
Chemical loads and cleaning agents must be tested beforehand.
1. Flexible acid-resistant sealant BOTON® SF 400
2. BOTACT® Sealing and Decoupling Membrane
3. Flanged drain
4. Epoxy resin primer BOTON® E 120 1:4 with quartz sand
5. Flange
6. Sealing tape BOTACT® SB 78
8. Slip-resistant tile cover
9. Special joint mortar BOTON® CF 200 /
Epoxy resin joint mortar BOTON® EF 500
10. Epoxy resin adhesive BOTON® EK 500
18
19.10.2010
10:48 Uhr
Seite 19
SYSTEM COMPONENTS
Levelling mortar
BOTACEM® M 100
Epoxy resin coating 2c
BOTON® E 170 or
membrane
At heavy duty with
BOTON® EK 500
BOTON® CF 200
At heavy duty with
BOTON® EF 500
Epoxy resin primer 2c
BOTON® E 120 +
Quarzsand 1:4
BOTON® SF 400
19
19.10.2010
Laboratories.
SYSTEM COMPONENTS
Copper conductive tape
High performance tile adhesive 2 c
BOTON® TK 150
Acid resistant grout 2 c
BOTON® SF 100
Acid resistant sealant 2 c
BOTON® SF 400
20
10:48 Uhr
Seite 20
19.10.2010
10:49 Uhr
Seite 21
4
5+6
3
2
1
Installations in Objects
In the pharmaceutical, print,
paint and lacquer industry, as
well as in computer and operating rooms, production plants
and laboratories, the demand for
conductive floor covering is on
the rise since electrostatic charge
has often highly undesirable consequences.
In this area our special adhesive
mortars and joint mortars with
high electrostatic discharge offer
reliable protection.
The threshold value of the resistance to ground (RTG) depends
on the respective local conditions. In general, an RTG of 106 is
sufficient.
Where particularly cap-sensitive,
potentially explosive substances
are present, a reduction of the
earth resistance value (correlates
to an improvement of conductivity) may be necessary.
1
Fitting of copper conductive tape
onto the floor areas.
3
Inserting the conductive tiles into
BOTON® TK 150 adhesive bed
2
Application of BOTON® TK 150
with suitably sized notched trowel.
4
Preparing the base with BOTON®
TK 150.
With BOTON® TK 150 and
BOTON® SF 100 we fulfil these
criteria. Sources of literature for
the production of static-dissipative floor coverings are DIN EN
1081, the AGI worksheets S 30
and S40 and Botament’s own,
comprehensive company literature.
5
Jointing the conductive joint mortar BOTON® SF 100.
6
Washing the conductive joint
mortar BOTON® SF 100. It is important to produce a joint that is
flush with the surface
21
19.10.2010
10:49 Uhr
Seite 22
Installation details 10.02.
It is important to only fit flanged drains and to produce
wall connection of at least 25 cm height.
3. Sealing tape BOTACT® SB 78 at waterproofing level
4. Earth potential connector
5. Copper tape in a grid of 5 x 5 m
6. Solder point
7. Solder point at the joint profile
8. Joint profile
9. Electrically conductive ceramics
10. Conductive joint mortar BOTON® SF 100
11. Conductive tile adhesive BOTON® TK 150
22
19.10.2010
10:49 Uhr
Seite 23
SYSTEM COMPONENTS
Levelling mortar
BOTACEM® M 100
Bonded waterproofing with
membrane
High performance tile adhesive 2 c
BOTON® TK 150
BOTON® SF 100
BOTON® SF 400
12
23
19.10.2010
Food sector.
SYSTEM COMPONENTS
Deep-action Primer
BOTACT® D 11
oder Rapid Adhesive
BOTACT® M 10 Speed
BOTACT® SB 78
membrane
BOTON® S 250
or special grout, 2 comp.
BOTON® CF 200
24
10:49 Uhr
Seite 24
19.10.2010
10:49 Uhr
Seite 25
5+6
4
2+3
1
Sealing membranes in the food sector
Here safety, cleanliness and hygiene are called for: stringent
hygiene regulations are a legal
requirement for the food &
drinks industry.
Our special joints give you
safety and cleanliness.
Our joint mortars BOTON® CF
200 and BOTON® S 250 have
both been tested for drinking
water and food stuffs in accordance with DVGW W 347.
Particular attention in this area
must be paid to the fitting of
tiles and natural stones in cold
stores, where the layer structure in bonded insulation must
be carried out with extreme
care.
Our Flexible Speed Adhesive
BOTACT® M 10 Speed can be
processed in temperatures as
low as +3°C, which makes it
ideal for repair works, too.
1
2
Priming the screed with BOTACT
D 11.
®
3
Installing sealing tape and interior
corner BOTACT® SB 78 into BOTACT® M 21 Classic/BOTACT® M 10
Speed
4
Fitting the BOTACT® Sealant and Decoupling Membrane into BOTACT®
M 21 Classic / BOTACT® M 10 Speed.
5
Fitting of tiles/slabs with BOTACT®
M 21 Classic / BOTACT® M 10
Speed.
6
BOTON®®
Jointing tiles/slabs with
CF 200 or BOTON® S 250.
Light, streak-free washing of
BOTON® CF 200 or BOTON® S 250.
25
26
19.10.2010
10:49 Uhr
Seite 26
19.10.2010
10:50 Uhr
Installation details
Seite 27
10.01.
1. Flexible acid-proof sealant BOTON® SF 400
3. Flanged drain
4. Epoxy resin-primer BOTON® E 120 1:4 with quartz sand
5. Flange
6. Sealing tape BOTACT® SB 78
7. Flexible superior adhesive BOTACT® M 21 Classic
8. Special joint mortar BOTON® CF 200
SYSTEM COMPONENTS
Levelling mortar
BOTACEM® M 100
membrane
Renovating caulking strip
BOTACT® SB 78
or Rapid Adhesive
BOTACT® M 10 Speed
BOTON® CF 200
BOTON® SF 400
27
19.10.2010
Drain details
10:50 Uhr
Seite 28
08.01.03
By the flange the BOTACT® Sealing and Decoupling Membrane
must be sealed using the epoxy resin-primer BOTON® E 120.
1. Bonded waterproofing with the BOTACT® Sealing and
Decoupling Membrane
3. Acid-resistant sealant BOTON® SF 400
4. Wall and floor levelling if need be using levelling mortar BOTACEM® M 100
5. Installing the ceramic tiles with tile adhesive
BOTON® TK 150 / BOTACT® M 21 Classic
6. Jointing the ceramic tiles with special joint mortar BOTON® CF 200
28
19.10.2010
10:50 Uhr
Seite 29
SYSTEM COMPONENTS
BOTACT® Thin
de-coupling membrane
on bottom area
or Rapid Adhesive
BOTACT® M 10 Speed
and epoxy resin adhesive
BOTON® EK 500
BOTON® CF 200
Levelling mortar
BOTACEM® M 100
29
19.10.2010
Public areas.
SYSTEM COMPONENTS
Deep-action Primer
BOTACT® D 11
or Rapid Adhesive
BOTACT® M 10 Speed
BOTACT® SB 78
membrane
Mosaic with Mosaic &
Mosaic grout 2c
BOTON® MF 300 (up to 5 mm) or
swimming pool grout 2 c
BOTON® S 250 or
BOTON® CF 200
Renovating silicone
SUPAX® S 5
30
10:50 Uhr
Seite 30
19.10.2010
10:51 Uhr
Seite 31
6
5
3+4
2
1
Premiu
m
BOTACT ® quality!
M
21
and BO
TACT ® M Classic
10 S
system
-tested peed
!
Installation in wet rooms
Waterproofing in public areas.
Sealing membranes are increasingly used to waterproof showers and bathrooms as they
save time.
In this area Botament® offers
the great advantage, that with
either the Flexible Superior Adhesive BOTACT® M 21 Classic or
the Flexible Rapid Adhesive BOTACT® M 10 Speed only two
products are required to carry
out the entire waterproofing
and bonding structure.
Once the points for each individual bathroom fitting have
been decided, such as WC,
wash basin, bathtub and shower, and once all installation
works have been completed,
the sealing procedure for these
can begin.
Tile fitting is then already possible the next day.
1
2
Priming with BOTACT D 11.
®
3
Fitting of the BOTACT® Sealing and
Decoupling Membrane into BOTACT® M 21 Classic / BOTACT® M 10
Speed.
5
Fitting of the cover with BOTACT® M
21 Classic / BOTACT® M 10 Speed.
Application of BOTACT® M 21 Classic
/ BOTACT® M 10 Speed after the sealant and interior corner BOTACT® SB
78 have been installed.
4
Insertion of the BOTACT® Sealing
and Decoupling Membrane at the
wall area.
6
Jointing with BOTON® MF 300,
BOTON® S 250 or BOTON® CF 200.
31
32
19.10.2010
10:51 Uhr
Seite 32
19.10.2010
10:51 Uhr
Seite 33
Shower details
1. Sealing Tape BOTACT® SB 78
2. BOTACT® SB 78 cuff into the BOTACT® DF 9 sealant
3. Sealing in the BOTACT® Sealing and Decoupling
Membrane at the flange
4. Sanitary silicone SUPAX® S 5
5. Drain
SYSTEM COMPONENTS
Levelling mortar
BOTACEM® M 100
Thin de-coupling
membrane
on bottom area
flexible water-proofing
BOTACT® MD 1 or
BOTACT®
BOTACT® MD 28 and
Damp-proof membrane
BOTACT® DF 9
or Rapid Adhesive
BOTACT® M 10 Speed
BOTON® CF 200 or
Mosaic grout 2c
BOTON® MF 300 or
Swimming Pool Grout
BOTON® S 250
Renovating silicone
SUPAX® S 5
33
19.10.2010
Wellness.
SYSTEM COMPONENTS
Deep-action Primer
BOTACT® D 11
or Rapid Adhesive
BOTACT® M 10 Speed
membrane
BOTACT® SB 78
Mosaic grout 2c
BOTON® MF 300 (up to 5 mm) or
BOTON® S 250 or
BOTON® CF 200
Special-grout
BOTON® CF 600
34
10:51 Uhr
Seite 34
19.10.2010
10:51 Uhr
Seite 35
6
5
3+4
2
1
Premiu
m
BOTACT ® quality!
M 21
and BO
TACT ® M Classic
10 S
system
-tested peed
!
Waterproofing membranes in wellness areas
Sealing Membrane in wellness areas
The waterproofing of floor covering constructions are especially
challenging, because these areas
are characterised by high room
temperatures coupled with high
humidity. Sealing membranes are
not just water impervious, highly
alkaline- and chemical-resistant,
but also have high resistance
against micro organisms.
Here Botament® provides with its
flexible superior adhesive BOTACT® M 21 Classic or BOTACT® M
10 Speed and with the BOTACT®
Sealing and Decoupling Membrane a couple of products which
are all that is required to produce
the entire structure in terms of
sealing and bonding.
Use of building boards
The water-repellent BOTACT®
Building Boards allow almost endless creative design possibilities.
They have the advantage that
they can be easily cut with a utility knife and are simply bonded
with silicone. Building boards can
either be used as carrier substrates for subsequent tiling or can be
used for decorative work or filling.
Benches, shower cubicles, shelves
and wall claddings can be quickly
and easily created from these carrier elements and can then be
worked on. With these quality
coated carrier elements loungers
become real eye-catching building parts.
1
2
Priming with BOTACT D 11.
®
3
Application of BOTACT® M 21 Classic
/ BOTACT® M 10 Speed after the sealant and interior corner BOTACT® SB
78 have been installed.
4
Fitting of the BOTACT Sealing and
Speed.
®
5
Fitting of the cover with BOTACT® M
21 Classic / BOTACT® M 10 Speed.
Insertion of the BOTACT® Sealing
and Decoupling Membrane at the
wall area.
6
Jointing with BOTON® MF 300,
BOTON® S 250 or BOTON® CF 200.
35
19.10.2010
10:52 Uhr
Car wash plants.
SYSTEM COMPONENTS
Deep-action Primer
BOTACT® D 11
or Rapid Adhesive
BOTACT® M 10 Speed
BOTACT® SB 78
membrane
BOTON® CF 200 or
BOTON® EF 500
for the rim-cleaning area
Acid resistant silicone
BOTON® SF 300
36
Seite 36
19.10.2010
10:52 Uhr
Seite 37
5+6
4
2+3
1
Premiu
m
BOTACT ® quality!
M
21
and BO
TACT ® M Classic
10 S
system
-tested peed
!
Installations in heavy-use wet rooms.
Waterproofing systems in car wash plants
Here oil is ever-present:
everywhere where vehicles are
washed and repaired, lubricants, alkaline cleaning agents
and acidic rim cleaners are unavoidable. Floors in car wash
plants are subjected to all of
the above loads.
Specially developed adhesive
mortars and joint mortars deliver improved safety in this area.
Depending on the respective
loading we recommend our silicate-based adhesive and joint
mortars BOTON® CF 200 and
BOTON® S 250 or even the
epoxy resin-based joint mortar
BOTON® EF 500.
It’ll pay off; even in car wash
places, where oil residue and
wash foam enter into a particularly risky marriage.
1
2
Priming the screed with
BOTACT® D 11.
3
Installing sealing tape and interior
corner BOTACT® SB 78 into BOTACT® M 21 Classic / BOTACT® M 10
Speed
4
BOTACT®
Inserting the
Sealing and
Speed.
Fitting the tiles / slabs with BOTACT® M 21 Classic / BOTACT® M 10
Speed using the combined method.
**Please follow our cleaning
recommendation here.
5
Jointing of tiles / slabs with BOTON®
CF 200 or BOTON® EF 500.
6
Light, streak-free washing of joints
made of BOTON® CF 200 or
BOTON® EF 500.
37
19.10.2010
10:52 Uhr
Seite 38
Vibrating floors 10.02.
It must be determined what kind of chemical
loads are to be expected.
3. Sealing tape BOTACT® SB 78 at waterproofing
level BOTACT® MD 28
4. BOTACT® M 25 flexible special contact slurry
5. Special joint mortar BOTON® CF 200 /
epoxy resinbased joint mortar BOTON® EF 500 jointing
6. Ceramics
38
19.10.2010
10:53 Uhr
Seite 39
Alternativ
Vibrating floors
SYSTEM COMPONENTS
membrane
BOTACT® SB 78
Fitting the ceramic with
flexible special contact slurry
BOTACT® M 25 Flex
fresh mortar bed
(vibration floor method)
BOTON® CF 200
At heavy duty with
BOTON® EF 500
BOTON® SF 300
39
19.10.2010
Factory.
SYSTEM COMPONENTS
Special contact slurry
BOTACT® M 25 Flex
Multipurpose grout
MULTIFUGE (3 – 30 mm) or
Special grout 2c
BOTON® CF 200
BOTON® SF 300
40
10:53 Uhr
Seite 40
19.10.2010
10:53 Uhr
Seite 41
4+5+6
3
2
1
Installations in Objects
Conventional mortar bed
Conventional mortar bed tiling
is still being used today in garages, production halls, supermarkets and other heavy-load
areas where the vibration floor
method is also used.
Different load requirements
call for variable and sound solutions. The aspect “floor“ is no
different.
The highest stresses put on garages, supermarkets or on
showrooms are typical spheres
of action for vibration floors.
Investors like these floors, because of their early usability
and high stability.
1
Application of the special contact
slurry BOTACT® M 25 Flex as a bonding course.
3
Application of contact slurry
BOTACT® M 25 Flex.
5
Filling the joint with MULTIFUGE or
BOTON® CF 200.
2
Floating of screed.
4
Insertion of tiles into the still fresh
screed containing the contact
slurry BOTACT® M 25 Flex.
6
Streak-free washing of MULTIFUGE
or BOTON® CF 200.
41
19.10.2010
10:53 Uhr
Seite 42
Products, data and characteristics
Product overview
PRIMERS
BOTACT® D 11
Packaging
Product Description
Consumption
Claims
1 l bottle
(6/box)
5 l canister
(64/pallet)
10 l canister
(40/pallet)
200 l barrel
For the priming of very absorbent, mineral-bound substrates, gypsum renders, plasterboard building materials that receive a hydraulically cured thin-bed adhesive
grout. For binding dust and regulating absorption of
substrates made from concrete, screed, gypsum and
brickwork.
approx.
60-100 ml/m2
per layer
• For absorbent substrates
• For interior and exterior use
• Fast drying
• To be diluted 1:1
• Solvent-free
• Improves bonding
• Reduces absorbency
• Binds dust
Deep-action primer
Colour: reddish
BOTACT® D 15
Packaging
Product Description
Consumption
Claims
1 kg bottle
(6/box)
5 kg bucket
Now also suitable under levelling and filler compounds. As a bonding medium for problematic and
non-absorbent substrates, e.g. old tile covers, prior to
application of tile adhesives and levelling/filler compounds.
approx.
0,12 kg/m2
• For smooth and non-absorbent substrates
• For interior use
• Low emission
• Fast drying, goes a long way
• Can be used under levelling compounds
• For tile on tile laying
• High adhesionCan be rolled on or
brushed on
Bonding Primer
Colour: turquoise
BOTON® E 120
Packaging
Product Description
Consumption
Claims
1 kg kg tin
(6/box)
10 kg bucket
For the priming of mineral and non-absorbent substrates under solvent-free covers and coatings. As bonding
course under reaction resin coatings, mortars and covers and to produce epoxy resin grout.
approx.
100 – 300 g/m2
• Excellent bonding on absorbent and
non-absorbent substrates
• Excellent penetration properties
• To produce epoxy resin grout
Epoxy resin 2 comp. primer
Colour: clear
42
19.10.2010
10:53 Uhr
Seite 43
LEVELLING COMPOUNDS
BOTACEM® M 50
Levelling compound up
to 15 mm
Packaging
Product Description
Consumption
Claims
25 kg bag
(40/pallet)
For the levelling of uneven concrete floors and screed
surfaces with excellent resistance against mechanical
loads.
approx.
1,6 kg/m2
per mm layer
thickness
• For interior and exterior areas
• Ready to be covered after approx. 6 h.
• For heated areas
• High surface hardness, castor-proof
• Seamless flow properties
• Layer thicknesses of up to 15 mm in
one working process
• Low emission
Colour: grey
BOTACEM® M 51
Levelling compound
5 to 30 mm
Packaging
Product Description
Consumption
Claims
25 kg bag
(40/pallet)
For the levelling of uneven concrete floors and screed
surfaces with excellent resistance against mechanical
loads for interior and exterior areas.
approx.
1,8 kg/m2
per mm layer
thickness
• For heated areas
• Layer thicknesses of 5 to 30 mm in one
• working process
• Low emission
• High surface hardness, castor-proof
• Seamless flow properties
Colour: grey
BOTACEM® M 52 Duoplan
Lightweight self-levelling compound up to 30 mm
Packaging
Product Description
Consumption
Claims
15 kg bag
(50/pallet)
Levelling compound that goes a long way and minimises dust; with lightweight aggregates to level concrete
and screed surfaces in interior and exterior areas.
approx.
1,3 kg/m2
per mm layer
thickness
• For underfloor heating
• Layer thicknesses of up to 30 mm in
one working process
• Goes a long way
• Low emission
• High surface hardness
• Minimized dusting during mixing
Colour: grey
LEVELLING MORTARS
BOTACEM® M 90
Light and stable levelling
mortar up to 30 mm
Packaging
Product Description
Consumption
Claims
20 kg bag
(40/pallet)
Fine levelling mortar that goes a long way for the repair and render of wall and floor areas made from
concrete and cement screeds. For the production of
gradient and levelling layers of thin and thick layer
thicknesses. Enables a fast substrate preparation prior
to laying tiles and floor slabs.
approx.
1,3 kg/m2
per mm layer
thickness
• For layer thicknesses of up to 30 mm
• Ready to be covered after approx. 2 hours
• For walls and floors
• Can be feathered out and smoothed
• Particularly smooth surface
• For areas permanently under water
• Goes a long way
Colour: grey
BOTACEM® M 100
Levelling grout from
3 to 50 mm
Packaging
Product Description
Consumption
Claims
25 kg bag
(40/pallet)
Fine levelling grout that goes a long way for the repair
and render of wall and floor areas made from concrete and cement screeds. For the production of gradient and levelling layers of thin and thick layer
thicknesses. Enables a fast substrate preparation prior
to laying tiles and floor slabs.
approx.
1,3 kg/m2
per mm layer
thickness
• For layer thicknesses from 3 - 50 mm
• Ready to be covered after approx. 2 hours
• Can be feathered out and smoothed
• For mineral concave mouldings
Colour: grey
43
19.10.2010
10:53 Uhr
Seite 44
Product overview
SEALANTS
BOTACT® SB 78
Packaging
Product Description
Claims
Sanitary sealant tape
and accessories
50 m roll (12,0 cm)
BOTACT® SB 78 sanitary tape and accessories for waterproofing joints and corners in wet areas such as Swimming pools as well as slightly chemically loaded areas in
conjunction with the special waterproofing compound
BOTACT® MD 1, BOTACT® MD 28, BOTACT® DF 9 or the
epoxy resin waterproofing BOTON® RA 170.
• Highly elastic
• Highly tear-proof
• Excellent bonding
Interior edge
Exterior edge
(both in 10 units)
Sealing collar
120 x 120 mm
425 x 425 mm
(both in 10 units)
Colore: blue
Packaging
Product Description
Claims
30 m2 box
30 m roll (1 m wide)
BOTACT® Sealing and Decoupling Membrane is a crackbridging membrane made from polyethylene with a special fleece fabric on either side for more effective
anchoring in the tile adhesive. It is bonded to a level substrate with BOTAMENT® tile adhesive. Tiles are layed directly onto the membrane using the thin-bed method.
Colour: blue
• Elastic, highly tearproof
• For moist areas, terraces and balconies
• Rapid succession of working steps
• Excellent rotting resistance
• For industrial kitchens and other areas
subject to heavy chemical stresses
BOTON® RA 170
Packaging
Product Description
Consumption
Claims
Epoxy resin waterproofing
membrane, 2 comp
10 kg bucket
To seal mineral and metal substrates under tile covers
that are subject to heavy chemical and mechanical
loads.
approx. 1,4
kg/m2
per mm layer
thickness
• Highly flexible
• Joint sealing under tiles
• For many mineral and steel substrates
Colour: grey
BOTACT® MD 1
Flexible Waterproofing
Compound
Packaging
Product Description
Consumption
Claims
20 kg bag
(40/pallet)
Hydraulically waterproofing, crack-bridging waterproofing for wall and floor areas in interior and exterior areas directly under ceramic covers. The product is
ideal for the flexible sealing on balconies and terraces,
in damp areas and wetrooms.
approx.
1,4 kg/m2
per mm layer
thickness
• Highly elastic
• For rollers and spatulas
• Open to vapour diffusion
• For joint sealing under tiles
Colour: grey
BOTACT® MD 28
Special Waterproofing
Compound, 2 component
Packaging
Product Description
Consumption
Claims
25 kg powder
10 kg emulsion
35 kg unit
For the crack-bridging waterproofing under tile covers
in interior and exterior areas, e.g. on terraces and balconies and in swimming pools and wellness areas.
approx.
1,6 kg/m2
per layer
thickness
• Highly elastic
• For joint sealing under tiles
Colour: grey
BOTACT® DF 9 S/R
Packaging
Product Description
Consumption
Claims
For spatula:
12 kg bucket
21 kg bucket
(16/pallet)
For the seamless and joint-free surface sealing of
damp spaces that are to receive tile cover. Excellent adhesion with mineral tile adhesives.
approx. 1,2
kg/m2 per mm
layer thickness
• Highly elastic
• Solvent-free
• For interior use
• For rollers and spatulas
Sealing membrane
For roller:
3 kg bucket
12 kg bucket
21 kg bucket
(16/pallet)
44
Colour: grey
19.10.2010
10:53 Uhr
Seite 45
TILE ADHESIVE
BOTACT® M 10 Speed
Rapid flexible adhesive,
thin-bed/pourable bed
BOTACT® M 12 Stone
Natural stone adhesive
Thin-bed/Pourable bed
BOTACT® M 29
Packaging
Product Description
Consumption
Claims
25 kg bag
(40/pallet)
Rapid flexible adhesive for all tiling that needs to be
jointed and be ready for loading quickly. Enables rapid
work progression even in low temperatures. Suitable
for bonding porcelain stoneware, stoneware, vitreous
and non-vitreous stoneware, split tiles, clinker tiles,
mosaics, concrete and natural stone slabs which are resistant to discoloration.
Colour: light grey
6 mm notched
trowel approx.
2.3 kg/m2
8 mm notched
trowel approx.
2.8 kg/m2
10 mm notched
trowel approx.
3.6 kg/m2
• Ready to be jointed and walked on
after just 90 minutes
• Can be used in low temperatures
• For almost every kind of ceramic cover
• For heated floor surfaces
• Flexible
Packaging
Product Description
Consumption
Claims
25 kg bag
(40/pallet)
For the tiling of many calibrated hard and soft stones
susceptible to discoloration. Due to a novel mode of
action combination and crystalline water retention efflorescence and discolorations are mostly prevented.
• For almost all natural stones
• Fast setting
Colour: light grey
6 mm notched
trowel approx.
2.5 kg/m2
8 mm notched
trowel approx.
3.5 kg/m2
10 mm notched
trowel approx.
4.0 kg/m2
Packaging
Product Description
Consumption
Claims
25 kg bag
(40/pallet)
For an almost cavity-free laying of large-scale ceramic
or porcelain stoneware tiles and slabs on balconies and
terraces, in industrial halls and other construction projects subjected to high mechanical loads. Maximal
layer thickness 20 mm.
10 mm notched
trowel approx.
4.7 kg/m2,
medium-bed
approx.
7.0 kg/m2
• Flexible
• Almost cavity-free bonding
• For heated floor surfaces, terraces and
balconies
• Quickly walk-able and grout-able
• For almost all ceramic coverings
• For high mechanical loads
Flexible fluid-bed grout
Colour: grey
BOTACT® M 25 Flex
Packaging
Product Description
Consumption
Claims
25 kg bag
(40/pallet)
For the secure bonding between fresh screed and ceramic covers. Improves adhesion of porcelain stoneware
tiles. Also suitable on underfloor heating and as bonding
course for smooting compounds. As bonding course between old and new concrete and screed layers.
approx. 1,6
kg/m2
per mm layer
thickness
• Flexible
• Suitable for vibration floors as bonding
course, for fresh-on-fresh tile laying
• For almost all ceramic coverings
• Long open time, high adhesion
Special contact slurry
Colour: grey
BOTON® TK 150
Highly resistant tile adhesive
2 comp.
Packaging
Product Description
Consumption
Claims
25 kg powder
5 kg liquid c.
30 kg unit
For the bonding of floor and wall covers in areas that are
subjected to aggressive, gaseous, liquid and solid substances.
6 mm notched
trowel approx.
3.8 kg/m2
8 mm notched
trowel approx.
4.3 kg/m2
10 mm notched
trowel approx.
5.4 kg/m2
• Mineral and inorganic silicate grout
• Resistant to a diverse range of chemicals
• High temperature resistance
• No unpleasant odour during application
• For ceramic covers capable of static conductivity
Product Description
Consumption
Claims
For the bonding of ceramic covers in areas subjected
to extremely high chemical and mechanical loads.
6 mm notched
trowel approx.
2.8 kg/m2
• Flexible
• High chemical resistance
• Good adhesive strength
• High abrasion resistance
• For swimming pools and drinking
water containers
Colour: grey
BOTON® EK 500
2 component
Packaging
5 kg bucket
(compound unit)it)
Colour: grey
45
19.10.2010
10:53 Uhr
Seite 46
Product overview
GROUTS AND SEALANTS
BOTON® MF 300
Mosaic and swimming pool
grout, 2 comp.
Packaging
Product Description
Consumption
Claims
10 kg powder
(2 x 5 kg)
3 kg liquid.
(2 x 1,5 kg)
13 kg unit
(16/pallet)
Joint grout on a mineral inorganic basis for use in small
joints. The material is ideal for use in public pools, shower areas, saunas and everywhere where glass or ceramic mosaics are being used.
Mosaic
2,5 x 2,5 cm =
approx. 1,5
kg/m2
• Joint widths of up to 5 mm
• Mineral and inorganic material basis
• Highly resistant against micro
biological infestation
• Good shoulder bonding
• High pressure and abrasion resistance
• 2 components in one container
• Hydrophobic and dirt-repellent surface
Produktbeschreibung
Verbrauch
Auslobungen
For grouting floor and walls in areas exposed to chemi-
Split tiles
24 x 11,5 cm =
approx. 2,40
kg/m2
• Mineral inorganic silicate-based grout.
• Versatile resistance to acid and
chemicals.
• High temperature-resistance.
• Anti-static.
• High compressive strength and
flexural strength.
Colour: grey, white
BOTON® SF 100
Lieferform
Acid resistant grout
25 kg
5 kg
30 kg
powder
liquid
cal stress, e.g. warehouses and laboratories .
unit
Vitreous
stoneware
20 x 20 cm =
approx.
0,87 kg/m2
Colour: grey
BOTON® EF 500
Epoxy resin joint grout,
2 comp.
Packaging
Product Description
Consumption
Claims
5 kg bucket
(compound unit)
For the grouting of ceramic coverings in areas subjected to high chemical and mechanical loads.
Split tiles
24x11.5 cm =
approx.1,86
kg/m2
• Joint widths of 2 to 10 mm
• Highly chemical resistant
• Best wash qualities
• High abrasion resistance
• Approved for swimming pools and
drinking water structures
Tiles
10x10 cm =
approx. 1,33
kg/m2
20x20 cm =
approx. 0,67
kg/m2
Colour: grey, silver-grey, white
MULTIFUGE
Packaging
Product Description
Consumption
Claims
Multifuge is a multi-purpose joint grout with a very
broad application spectrum and excellent application
characteristics.
Split tiles
24 x 11.5 cm =
approx. 1,75
kg/m2
• For joint widths of 3 to 30 mm
• Flexible
• Washable and fast curing
• For heated floor surfaces, terraces
and balconies
• For almost all ceramic coverings and
many natural stones
• Excellent washing qualities
• Early accessibility and utilisation
• Water and dirt-repellent
• Low emission
Multi-purpose grout
5 kg bag
(4/Folie)
25 kg bag
(40/pallet)
Tiles
20 x 20 cm =
approx. 0,63
kg/m2
Colours: grey, silver-grey, titan-grey, charcoal
46
MULTIFUGE Schmal NEW!
19.10.2010
Packaging
10:53 Uhr
Seite 47
Product Description
Consumption
Claims
Multifuge Schmal is a multi-purpose joint grout with a
very broad application spectrum and excellent application characteristics. Due to its fine and brilliant surface
it is especially suited for wall surfaces.
Mosaic =
2,0 x 2,0
approx.
1.0 kg/m2
• For joint widths of up to 7 mm
• Fine and brilliant surface
• For almost all ceramic coverings and
many natural stones
• Flexible and fast curing
• Also for glass tiles and glass mosaics
• Water and dirt-repellent
• For heated floor surfaces, terraces
and balconies
• Excellent washing qualities
• Low emission
Multi-purpose grout
4 kg bag
(4/Folie)
(96/pallet)
15 kg bag
(50/pallet)
Tiles
30 x 60 cm =
approx. 0,26
kg/m2
Colours: grey, silver-grey, titan-grey, pergamon, white,
Bahama, brown, Manhattan
BOTON® CF 200
Highly resistant tile adhesive
2 comp.
Packaging
Product Description
Consumption
Claims
10 kg powder
(2 x 5 kg)
2 kg liquid (2 x 1 kg)
12 kg unit
For the grouting of floor and wall covers in areas that
are subjected to high mechanical loads, in industrial
projects and areas with exposure to aggressive substances.
Mosaic
2,0x2,0 cm =
approx. 1,55
kg/m2
• For joint width of 2-20mm
• Mineral-anorganic material
composition
• High chemical resistance
• Open for water vapour diffusion, high
steam cleaning resistance
• High adhesion to tile shoulders
• High compression and abrasion
resistance
Tiles = approx.
10x10=1,64
kg/m2
25 kg powder
5 kg liquid c.
30 kg unit
Colour: grey
BOTON® S 250
Packaging
Product Description
Consumption
Claims
10 kg powder
(2 x 5 kg)
2 kg liquid
(2 x 1 kg)
12 kg unit
(16/pallet)
For the grouting of floor and wall covers in Swimming
pools, public showers and many brine baths. The mineral material basis ensures increased resistance against
attack from micro organisms.
Split tiles
24 x 11,5 cm =
approx.
2,35 kg/m2
• Joint widths from 2 to 20 mm
• Mineral and inorganic material basis
• Highly resistant against micro
biological infestation
• High pressure and abrasion resistance
• 2 components in one container
• Hydrophobic and dirt-repellent surface
Swimming pool grout, 2 comp.
Colour: grey
47
19.10.2010
10:53 Uhr
Seite 48
Product overview
GROUTS AND SEALANTS
SUPAX® S 5
Packaging
Product Description
Claims
300 ml cartridge
(20/box)
For the installation of elastic expansion and connection joints in sanitary and wet areas on glass, enamel
and ceramics.
• Flexible
• Fungicidal agent after curing
(exception: transparent)
• Optimal shoulder bonding
• Acid cross-linking
Sanitary silicone
Colours: transparent (Nr.01), white (Nr.10), pergamon (Nr.11),
whisperblue (Nr. 12), whisperpink (Nr. 13), aegean (Nr. 14), silvergrey (Nr. 16), lightgrey (Nr. 19), sunset (Nr. 21), concretegrey (Nr. 22), manhattan (Nr. 23), grey (Nr. 24), titangrey (Nr.
25), anthracite (Nr. 26), evergreen (Nr. 28), jasmin (Nr. 29),
bamboo (Nr. 32), bahamabeige (Nr. 33), caramel (Nr. 34), terrabrown (Nr. 36), ochre (Nr. 37), cocoa (Nr. 38), honey (Nr. 39),
crocus (Nr. 44),melba (Nr. 48), mento (Nr. 55), azureblue (Nr.
57), terracotta (Nr. 58), mint (Nr. 59), black (Nr. 90)
BOTON® SF 300
Packaging
Product Description
Claims
300 ml cartridge
(20/box)
For closing joints and connections in areas subjected to
chemical loads, e.g. warehouses, industrial kitchens and
washing plants.
• Flexible
• Increased chemical resistance
• Optimal shoulder bonding
• Sour cross-linking
• Silky-matt surface finish
Acid-resistant silicone
Primer BOTON® P 300
100 ml catridge
(15/box)
Colour: grey
BOTON® SF 400
Packaging
Product Description
Claims
2.5 l tin (4/box)
For the sealing of joints and connections in areas subjected to chemical loads, e.g. laboratories, washing
plants etc. and in areas where high-pressure cleaners
are used.
• Use trowel to apply or spray
application
• To be used in combination with
BOTON® P 400
Acid-resistant sealant
Primer BOTON® P400
1 l tin (6/box)
Colour: grey
BOTON® CF 600
Packaging
Product Description
Claims
310 ml cartridge
(12/box)
For sealing of joints and connections in chemically stres-
• Highly resistant against
permanent moisture load.
• Strong fungicidal agent.
• For pool area.
• 1-component system.
• Neutrally cross-linking.
• Use with Primer BOTON® P 600
Special sealant
sed areas, such as Swimming pools, laboratories, car
washes, etc., and in areas where work is with high presPrimer BOTON® P 600
100 ml cartridge
(6/box)
sure cleaners.
Colour: grey, white
48
19.10.2010
10:53 Uhr
Seite 49
BITUMINOUS HEAVY COATINGS
BOTAZIT® GS 98
Packaging
Product Description
Consumption
Claims
mesh size
5/5 mm
Reinforcement layer for sealing systems according to
approx.1.2 m2/m
DIN 18195 and forsubstrates with risk of cracking.
with 10 cm over-
• Highly tearproof.
• Recommended for better control
of layers thickness
• Required by DIN 18195,
part 5 and 6.
• System examined
Glass fibre fabric
Roll 50 m2
(1 x 50 m)
lapping.
Embed into the thick coatings:
BOTAZIT® BM 1,
BOTAZIT® MACH3IN11,
BOTAZIT® BM 92 Schnell,
BOTAZIT® BM 92 Winter,
BOTAZIT® BE 91.
Colour: white fabric
BOTAZIT® B 180
Packaging
Product Description
Claims
Roll 6 m
For bridging and sealing construction and
• Perforations for better
(18 cm wide)
expansion joints in buildings.
Joint tape
drying purposes.
• For joints widths of 6 cm.
• Can be used with epoxy resin
BOTON® E 170.
• Weldable.
Colour: grey
ACCESSORIES
Conductive copper tape
Packaging
Product Description
16,5 m roll
(12 mm wide)
For installation of flooring capable of electric discharge.
Self-adhesive.
49
19.10.2010
10:53 Uhr
Seite 50
Product overview by application area
Adhesive mortar for walls and floors
• Is suitable
Self-levelling mortar up to 30 mm
BOTACEM® M 52 Duoplan
Self-levelling mortar 5 – 30 mm
BOTACEM® M 51
BOTACEM® M 50
Self-levelling mortar up to15 mm
Levell
Epoxy - resin primer 2c
BOTON® E 120
Deep-action Primer
Primer
BOTACT® D 11
Substrate
Application area
Swimming pool
•
•
Industrial kitchen
•
•
•
•
•
•
Food & drinks areas
•
•
•
Public showers
•
•
Wellness areas
•
•
•
Car wash plants
•
•
•
Factories
•
•
•
Application area
Swimming pool
•1
•
Industrial kitchen
•
•
•
•
•
•
Food & drinks areas
•
•
•
•
•
Public showers
•
•
•
•
•
Wellness areas
•
•
•2
•2
•
Car wash plants
•
•
Factories
•
•
1) Not in the pool
2) Not in the Steam sauna
3) Wall area
50
•1
•
•
•
•
•
•
Renovating caulking strip
BOTACT® SB 78
Special-purpose sealing agent 2 c
BOTACT® MD 28
Flexible water-proofing
Tile Glue 2C
BOTACT® MD 1
epoxy resin coating 2 c
BOTON E 170
®
Thin de-coupling membrane
Sealing
BOTACT®
Substrate
•
•
•
•
•1
•
•
•
•
•
•
•
•
•
•
•
•
•
•1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Mosaic and swimming pool grout
•
BOTON® MF 300
•
Special grout 2c
•
BOTON® CF 200
•
Special-joint grout, 2c
High performancetile adhesive 2 c,
C2 FE
BOTON® TK 150
Tile Glue 2CR2 TE
Polyurethane Resin -
BOTACT® PU 550
Epoxy adhesive 2 c R2 T
BOTON® EK 500
10:54 Uhr
BOTON® CF 600
Multipurpose grout
•
•
MULTIFUGE®
Flex tile adhesive to pour C2 E
BOTACT® M 29
C2 TE
19.10.2010
Renovating silicone
SUPAX® S 5
Epoxy resin grout
Rapid Adhesive
Dünnbett / Fließbett, C2 FT
BOTACT® M 10 Speed
Levelling mortat
BOTACEM® M 100
Light and firm levelling filler
offering up to 30 mm thickness
BOTACEM® M 90
eveller
BOTON® EF 500
Acid resistant sealant 2 c
BOTON® SF 400
BOTON® SF 300
BOTON® SF 100
Swimming pool grout 2 c
BOTON® S 250
Seite 51
Tile and natural stone adhesive
•
•
Grout
•
•
•3
•
51
19.10.2010
10:54 Uhr
Seite 52
Product overview
Adhesive mortar for walls and floors
•• Is highly recommended
Mosaic grout 2 c, bis 5 mm
BOTON® MF 300
Epoxy resin adhesive and
grout 2 c
2 – 10 mm
BOTON® EF 500
Swimming pool grout 2 c
2 – 20 mm
BOTON® S 250
Special-purpose grout 2 c
2 – 20 mm
BOTON® CF 200
Coloured joints, up to 5 mm
Flexible grout, 2 – 30 mm
BOTACT® M 30
Multi-purpose grout
Bis 7 mm
MULTIFUGE Schmal
Multi-purpose grout
3 – 30 mm
Joint grout
MULTIFUGE
Substrate
SUPAX® M 32
• Is suitable
Slabs
Non-vitreous stoneware
•
••
•
••
•
•
•
•
Vitreous stoneware, unglazed, up to 15 x 15 cm
••
••
••
••
••
••
•
••
Vitreous stoneware, large-formats
••
••
••
••
••
••
•
••
Stoneware tile strips, glazed, e.g. 6 x 24 cm
••
••
••
••
Porcelain stoneware
••
••
••
••
••
••
••
Porcelain stoneware, polished
••
••
•
••
••
••
••
Pre-fabricated concrete tiles, Terrazzo tiles
••
•
•
•
•
•
•
••
••
••
••
••
••
Mosaic made from glass
••
•
Mosaic made from ceramic
•
••
••
Mosaic made from artificial stone flags
••
••
••
•
•
••
••
Composite boards (e.g. Object Stone)
••
••
••
••
••
•
••
Clinker, split tiles, tile strips, glazed
••
•
••
••
••
Coarse pottery, large-format (handmade)
••
•
•
•
Cotto tiles (after preparation following
manufacturer’s instructions)
••
•
•
Glass bricks
••
••
••
Glass tiles
•
•
••
•
Natural stones 1)
Marble
••
Granit
••
••
Solnhofener slabs, calibrated
••
••
Slate tiles
••
••
Natural stone mosaic
•
••
•
•
1) We recommend a preview bonding and grouting.
52
•
••
19.10.2010
10:54 Uhr
Seite 53
For each load and requirement
The correct sealing
Epoxy resin coating 2 c
BOTON® E 170
BOTACT® Sealing and
insulating sheet
Special-purpose sealing
agent 2 c
BOTACT® MD 28
Flexible water-proofing
compound
BOTACT® MD 1
Damp-proof membrane 1 c
BOTACT® DF 9 S
Damp-proof membrane 1 c
Sealing
BOTACT® DF 9 R
Substrate
High load –
Area regulated by building authorities
A
from non-pressing water in interior areas
1
1
B
high load from permanent pressing water
from the inside in interior and exterior areas
C
high load from non-pressing water with additional chemical impact in interior areas
Moderate load
- Area not regulated by Building Authorities
A0
moderate load from non-pressing water in
interior areas
B0
moderate load from non-pressing water in
exterior areas
1) In high load areas only on walls.
53
19.10.2010
10:54 Uhr
Seite 54
Service.
Your contact at Botament® world wide
Germany:
Am Kruppwald 1
46238 Bottrop
Tel. 0 20 41 / 10 19 - 0
Fax 0 20 41 / 26 24 13
www.botament.de
Austria:
Tullner Straße 23
A-3442 Langenrohr
Tel. (0 22 72) 6 74 81
Fax (0 22 72) 6 74 81 35
France:
ZI Revoison
29, rue des Frères Lumière
F-69740 Genas
Tel: 04.78.90.24.36
Fax: 04.78.90.11.99
Email: [email protected]
www.botament.fr
Czech Republic:
Skandinávská 990
CZ-267 53 Žebrák
www.botament.at
Tel. 311 545 150
Fax. 311 537 118
Ireland:
MC Building Chemicals
Castleblayney
Co. Monaghan
[email protected]
www.botament.cz
Phone +353 42 / 9 75 15 20
Fax
+353 42 / 9 74 62 22
Slovakia:
Na Pántoch 10
SK-83106 Bratislava
www.botament.co.uk
Tel. +421/(0) 244 442 195
Fax +421/(0) 244 441 348
Great Britain:
MC-Building Chemicals, Unit 17
Stechford Trading estate
Lyndon Road, Stechford
GB-Birmingham B33 8BU
[email protected]
www.botament.sk
Phone +44 121 789 8333
Fax
+44 121 789 8595
www.botament.co.uk
Hungary:
MC-BAUCHEMIE KFT. BOTAMENT Üzletág
1117 Budapest Hengermalom u. 47/a
Tel: 481-38-50
Fax: 481-38-55
E-mail: [email protected]
www.botament.hu
54
19.10.2010
Poland:
Biuro handlowew Środzie Wlkp.
ul. Prądzyńskiego 20
Tel. 061 28 64 520
Fax. 061 2864 514
www.botament.pl
Switzerland:
MC-Bauchemie AG
Hagackerstrasse 10
8953 Dietikon
Schweiz
10:54 Uhr
Seite 55
Belgium:
MC-Bauchemie Belgium N.V.
Gen. De Wittelaan 9/6 b
2800 Mechelen
Bosnia and Herzegovina :
MC-Bauchemie d.o.o.
Tesanjska
(Objekat A 4-5) 1-11
71000 Sarajewo
Ukraine:
MC-Bauchemie TOV
Division Botament
Kievskaya oblast
ul. Mayakowskogo, 38
07541 Berezan
Romania:
MC-Bauchemie SRL
Str. Maguricea nr. 37-39
BI. 13D, Sc.2, Ap.11, Sect.1
014233 Bucuresti
Romania
55
19.10.2010
10:54 Uhr
Seite 56
Botament® locations at a glace
Sales office
Production site
Am Kruppwald 1
D-46238 Bottrop
Tel. +49 (20 41) 10 19-0
Fax +49 (20 41) 26 24 13
[email protected]
www.botament.com
Killycard
Castlebayney
Co. Monaghan
Tel. +353 (42) 9 75 15 20
Fax +353 (42) 9 74 62 22
www.botament.com
MC Bulding Chemicals
Unit17, Stechford Trading Estate
Lyndon Road, Stechford, Birmingham
B33 8BU
Tel.: + 44 121 789 8333
Fax: + 44 121 789 8595
www.botament.com

Tiling systems for industrial and residential buildings.

Transcription

Similar documents

English - ARDEX Americas

Your Masterpiece Deserves Only the Best.

RO-80 Grout Whitener

MusselBound Install

serving together

DETERDEK - Grout Haze Remover

STAINMASTER ® Stainproof Grout Tech Sheet

Tile Refinishing / Reglazing

Use In Correctional Facilities As High Strength Pick