Sigma Plus Multihead Weigher Training
Transcription
Sigma Plus Multihead Weigher Training
∑ Plus Multihead Weigher Training Program Contents Introduction ............................................................................................................................................ Course Modules ............................................................................................................................... Module 1: Introduction, Principals and Level 1 Operation Module 2: Mixing Level 1 2 3 ....................................................................... 3 ................................................................................................ 3 Module 3: Counting level 1 .......................................................................................... 3 Module 4: Level 2 and 3 .................................................................................................. Setting up a program 4 Module 5: Mixing Level 3 4 ................................................................................................ Module 6: Counting level 3 .......................................................................................... Module 7: Calibration (Day 1 or 2) ....................................................................... 4 .............................................................................. 4 ................................................................................... 5 ............................................................................................................. 5 ............................................................................................................................ 6 Module 8: Buckets (Setting Up) Module 9: System Installation and Maintenance Module 10: Hygiene Application Form 4 Tel: 0113 322 1546 Fax: 0113 350 2020 Email: [email protected] www.yamatoscale.co.uk 1 Introduction Would you like to improve efficiency, reduce giveaway and improve your ROI? Our tailor made training courses can guide your personnel through all aspects of your Yamato Weigher so that these improvements can be realised. The object of this training course is to train operators and engineers on all aspects of the Sigma Series Multihead Weigher by utilising various methods of presentation, including: • use of an interactive simulator • detailed power point presentations • hands on work in our demonstration area (subject to machine availability) The presentation is designed to be a complete course for all, the first part covers basic operation, higher level functions can also be incorporated to suit your specific requirements. Each attendee is provided with a handout which allows space for note taking. As we tailor each course to suit your requirements, we ask that you complete the attached ‘training request sheet’ when requesting one of our courses, this way we can ensure the correct level of training is provided. Training courses can be conducted at our Leeds Office where lunch is included and frequent coffee breaks. Alternatively we can come to your site and train you there - ask for details and requirements. We actively monitor our training programs and welcome any feed back and comments you and your personnel may have. Tel: 0113 322 1546 Fax: 0113 350 2020 Email: [email protected] www.yamatoscale.co.uk 2 Course Modules MODULE 1 INTRODUCTION About Yamato Principles of Operation Description of a Multihead Weigher ACCESS LEVEL 1 (BASIC OPERATION) Tare and Rezero Automatic Operation Language Selection Control of Product Flow Program change Printer Cleanout Histogram Manual Operation Sample Histogram CLEANING THE WEIGHER CHECKING FOR CORRECT OPERATION MODULE 2 MIXING LEVEL 1 (Operator/Supervisor and Engineers) MODULE 3 COUNTING LEVEL 1 (Operator/Supervisor and Engineers) Tel: 0113 322 1546 Fax: 0113 350 2020 Email: [email protected] www.yamatoscale.co.uk 3 Course Modules MODULE 4 ACCESS LEVELS 2 AND 3 (Advanced Operator/Supervisor and Engineers) Erase a Program Make Major Changes to the Program Settings (Weight, Speed, Limits) Full Access to the Printer Functions Create a new Program Erase the Histogram MODULE 5 MIXING LEVEL 3 (Advanced Operator/Supervisor and Engineers, setup mixing) MODULE 6 COUNTING LEVEL 3 (Advanced Operator/Supervisor and Engineers, setup counting) MODULE 7 CALIBRATION LEVEL 5 (ENGINEERS/QA) Calibration (As Level 4 without System Installation) MODULE 8 BUCKETS (MACHINE MINDER/ENGINEERS ONLY) Setting up bucket doors. Replacing bearings and bushes. Tel: 0113 322 1546 Fax: 0113 350 2020 Email: [email protected] www.yamatoscale.co.uk 4 Course Modules MODULE 9 ACCESS LEVEL 4 (Engineers Only) System Installation Full Access to all screens Maintenance Replacement of parts Fault Finding MODULE 10 HYGIENE (CLEANING CREW ONLY) Tel: 0113 322 1546 Fax: 0113 350 2020 Email: [email protected] www.yamatoscale.co.uk 5 Course Application The course is in modules. Please tick the modules required for your course and return this form to Yamato Service. MODULE DESCRIPTION PERSONNEL 1 Introduction, principles and Level 1 operation Operators to Engineers 2 Mixing Level 1 Operators to Engineers 3 Counting Level 1 Operators to Engineers 4 Level 2 and 3. Setting up a program Operators to Engineers 5 Mixing Level 3 Operators to Engineers 6 Counting Level 3 Operators to Engineers 7 Calibration (day 1 or day 2) Supervisors to Engineers 8 Buckets (setting up) Machine minder Engineers 9 System Installation and Maintenance Engineers Only Multiple choice test (Training certificate will state “have passed” instead of “have attended”) 10 Hygiene DAY 1 DAY 2 Operators to Supervisors (Level 3) Cleaning Crew Only Number of trainees on each day (maximum of 6 in total) Please enter the model and serial numbers of the machines you have on site and require training on. The training program can be adjusted to your specific machine requirements MODEL NO. SERIAL N0. OPTIONS (PLEASE TICK) ADW WG Collection bucket ADW WG Ring Gate ADW WG Infeed Funnel ADW WG Middle Shutter Tel: 0113 322 1546 Fax: 0113 350 2020 Email: [email protected] www.yamatoscale.co.uk 6 Course Application Example of 2 day course attendees: Day 1 - 6 attendees (4 operators and 2 engineers) Day 2 - 2 engineers only The course will be presented in the above order Module 1 is a ½ day (09:00-13:00) Module 1 & 4 will require a full day (0900-1600) Modules 2, 3, 5, 6 and 7 can be included but may/will extend the day. Modules 8 and 9 are a second day (09:00-14:30) + extra time for practical on a weigher if possible. NB: All training courses are to begin at 9am. Please arrive 15 minutes prior for registration Module 10 is for cleaning crew only. This takes approximately 1-1½hrs and will require access to a weigher (½hr in a classroom and ½hr on the weigher). Note: This is included in module 1. If you do not have counting or mixing software then please do not select them! If you are unsure then please contact Yamato Service Tel: 0113 322 1546 Fax: 0113 350 2020 Email: [email protected] www.yamatoscale.co.uk 7 3 Maple Park, Lowfields Avenue Leeds, LS12 6HH England Tel: 0113 322 1546 Fax: 0113 350 2020 Email: [email protected] www.yamatoscale.co.uk