Eaton® Char-Lynn® Spool Valve Hydraulic Motors

Transcription

Eaton®
Char-Lynn®
Spool Valve Hydraulic Motors
Spool Valve: J, H, S, T, W Series
B-1
B-2
B-3
B-4
B-5
Spool Valve motors incorporate the proven orbit motor
principle to provide high torque at low speeds.
EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011
B-i
Port B
Spool Valve Motors
Product Description
Bushing
Char-Lynn spool valve motors distribute pressurized fluid Port A
into and out of the Orbit gear set (Gerotor or Geroler) via
valve slots integrated into the output shaft. The spool valve
motors incorporate both valving and hydrodynamic journal
bearings into a common shaft design. The valve section
(spool valve) can be optimized for low flow, low speed
needs using a low speed spool option to enhance smooth
running performance.
Highlights
Thrust Bearing
These motors incorporate the proven orbit motor principle to
provide high torque at low speeds.
Motor shaft rotation can be instantly reversed by changing
direction of input/output flow while generating equal torque
in either direction. The displacements available provide a Actual Size
wide variety of speeds and torques from any spool valve
motor series.
J-2 Series
Motors
Spool Valve/Check Valves
Geroler
Gerotor Star
Motor Shaft Drive
Motor Shaft/Spool Valve
® Star
Motor Shaft Drive and Valve Drive
Motor Shaft
Port B
Port A
Port B
Bushing
Port A
Thrust Bearing
J-2 Series
Motors
Geroler
Motor Shaft
B-ii
Motor Shaft Drive
and Valve Drive
®
Star
Features, Benefits, and Applications
B-1
Features
Benefits
Applications
• Proven Orbit Motor
Principle
• Compact, powerful
package
• Harvesters
• Hydrodynamic Journal
Bearings
• Infinite bearing life
(at rated loads)
• Spreaders
• Constant Clearance
Geroler
• High efficiency
• Three-Zone Pressure
Design
• Reduced drive runningangle
• High-pressure seals
• Modular design
Design Features
• Increases shaft seal &
bearing life
Spool valve technology
is typically used where
compact, economical
solutions are most needed.
Spool valve motors use a
spool valve to precisely time
and control flow through
the orbit gear set (Gerotor
or Geroler). Inlet flow is
directed into and out of
the orbit set via slots in
the spool and passages
through the motor housing.
The result is a very costeffective compact package
suited to many application
requirements. The three
• Augers
• Conveyors
• Winches
B-4
• Turf care equipment
• Food processing
• Reduces leakage
• Aerial Work Platforms
• Design flexibility
• Anywhere a compact
drive with high output
torque is needed
primary components in
the motor are the orbit
star, drive and output
shaft. H, S and T Series
incorporate the spool valve
and hydrodynamic bearings
in the motor shaft. The W
series is similar except a
ball bearing is used for the
front bearing for increased
side-load capacity. Due to
its compact size and high
speed capability, the J
Series is unique and utilizes
a separate dedicated spool
and spool valve drive. All
motors utilize Eaton’s
B-3
• Machine tools
• Smooth operation,
increases drive life
• Economically tailored
solutions
B-2
B-5
constant-clearance Geroler
technology except the H
Series, which continues
to use the time-proven H
motor gerotor set. These
motors all use a three-zone
pressure design consisting
of three unique pressure
areas: 1) inlet, 2) return,
3) case. This provides the
capability to limit motor case
pressure and allows the use
of several case pressure
options for extended shaft
seal and thrust bearing life.
Below is a quick-guide to help select the proper motor for your application:
Motor Quick-Guide (based on maximum continuous ratings) Series Output Torque Nm [lb-in]
Pressure bar [psi]
Flow lpm [gpm]
Side Load
kg [lbs]
J Series 62 140 21 196
[550] [2030] [5.5] [430] H Series 407 124 57 635
[3607] [1800] [15] [1400] S Series 430
135 55 635 [3800] [2000] [15] [1400] T Series 450 155 55 635
[4000] [2250] [15] [1400] W Series 410 165 68 845 [3625] [2400] [18] [1900]
* The above are provided as guidelines only. Actual ratings vary depending on final motor configuration
B-iii
Table of Contents
HighlightsB-ii
T Series (158-)
Features, Benefits, and Applications
HighlightsB-4-1
B-iii
J Series (129-)
SpecificationsB-4-2
HighlightsB-1-1
Performance Data
SpecificationsB-1-2
Performance Data
B-1-3
DimensionsB-4-8
Product Numbers
DimensionsB-1-5
Model Code
Product Numbers
T Series with Parking Brake (185-)
B-1-9
B-4-3
B-4-9
B-4-10
Shaft Side Load Capacity
B-1-10
HighlightsB-4-11
Case Pressure and Case Drain
B-1-11
Application Information
Model Code
B-1-12
SpecificationsB-4-13
B-4-12
H Series (101-)
DimensionsB-4-14
HighlightsB-2-1
Brake Release and Motor Case Pressure
B-4-15
Product Numbers
B-4-16
B-4-17
SpecificationsB-2-2
Performance Data
B-2-3
Model Code
Dimensions
B-2-9
H, S and T Series (101-, 103-, 158-, 185-)
Product Numbers
B-2-10
Side Load Capacity
Model Code
B-2-11
Dimensions
B-4-19
S Series (103-)
Mounting Options B-4-21
HighlightsB-3-1
W Series (162-)
SpecificationsB-3-2
HighlightsB-5-1
Performance Data
SpecificationsB-5-2
B-3-3
B-4-18
DimensionsB-3-8
Performance Data
Product Numbers
DimensionsB-5-5
B-3-9
B-5-3
S Series with Low Speed Valving
B-3-10
Dimensions Shafts
B-5-6
Model Code
B-3-11
B-5-7
Model Code
B-5-8
W Series with Parking Brake (162-)
Dimensions
B-iv
B-5-9
Product Numbers
B-5-10
Model Code
B-5-11
J Series (129-)
Features:
• Constant clearance
Geroler set
Highlights
• Integrated check valves
• Self-lubricating shaft
bushing
Port B
Bushing
Port A
B-1
• High-strength rigid
components
• Increased valve seal lands
• High pressure seals
Thrust Bearing
• Variety of displacements,
shafts, mounts and
special options
Benefits:
J-2 Series
Motors
• High efficiency
Geroler
Motor Shaft
®
• Extended leak-free
performance
Star
• Powerful compact
package
Motor Shaft Drive
and Valve Drive
Applications:
Description
Char-Lynn J Series motors provide a lot of power from a
very small package. Up to 5 kW [6 1/2 HP] of power. These
motors are 61 mm [2.4 in] in diameter and 104 to 130 mm
[4.1 to 5.1 in] in length.
The J Series motor shaft and seal allows high case pressure
up to 76 bar [1100 PSI] return line pressure without case
drain line. When a case drain line is used a 220 bar [3190
PSI] peak pressure is allowed in the return line.
Geroler Element
Speed Pressure bar [PSI]
• Car wash tire spray wands
and brushes
• Marine bow thrusters
• Food processing
• Railroad maintenance
equipment
• Machine tools
• Conveyors
Specifications
Flow l/min [GPM]
• Agricultural augers,
harvesters, seeders
5 Displacements
21 [5.5] Continuous***
25 [6.5] Intermittent**
Up to 1992 RPM Cont.
Up to 2458 RPM Inter.
140 [2030] Cont.***
165 [2400] Inter.**
Torque Nm [lb-in] 62 [549] Cont.***
• Snow blower chute rotator
• Industrial sweepers and
floor polishers
• Saw mill works
• Turf equipment reel drives
• Paint stripper
• Many more
84 [743] Inter.**
***Continuous— (Cont.) Continuous rating, motor may be run continuously at these ratings.
** Intermittent— (Inter.) Intermittent operation, 10% of every minute.
Plastic Injection
Metal Forming
Food Processing
Ship-Boat Building
B-1-1
J Series (129-)
Specifications
Bearing Housing
Thrust Washer
Thrust Bearing
Bushing
O-ring Seals (3)
Check Valves
Valv e
Housing
Cap Screws (5)
Valve
Spool
Output Shaft
Exclusion Seal
Pressure Seal
Shaft Spacer
Drive
Spacer Plate
Geroler®
Spool Drive
Optional
Case Drain
(Shown with
Shipping Plug)
Specification Data — J Motors Displ. cm3/r [in3/r] Max. Speed (RPM) @ Continuous Flow Flow l/min [GPM] Continuous Intermittent Torque Nm [lb-in] Continuous Intermittent Peak
Pressure Continuous ∆ bar [∆ PSI] Intermittent Peak Weight kg [lbs] * Maximum pressure at
motor inlet port is 220
Bar [3190 PSI] without
regard to ∆ bar [∆ PSI] and/
or back pressure ratings or
combination thereof.
Note:
To assure best motor life,
run motor for approximately
one hour at 30% of rated
pressure before application
to full load. Be sure motor is
filled with fluid prior to any
load applications.
B-1-2
8,2 [.50] 1992 17 [4.5] 21 [5.5] 16 [141] 19 [164] 22 [193] 140 [2030] 165 [2400] 220 [3190] 2 [4.4] 12,9 [.79] 1575 21 [5.5] 25 [6.5] 25 [225] 30 [263] 36 [321] 140 [2030] 165 [2400] 220 [3190] 2,1 [4.6] 19,8 [1.21] 1043 21 [5.5] 25 [6.5] 38 [333] 46 [405] 48 [425] 140 [2030] 165 [2400] 220 [3190] 2,2 [4.8] ∆ Pressure:
Intermittent Operation:
The true ∆ bar [∆ PSI]
difference between inlet
port and outlet port.
10% of every minute
See individual shafts for
maximum torque recommendation. Splined shafts
are recommended for those
applications subject to
frequent reversals.
1% of every minute
Continuous Rating:
Motor may be run
continuously at these ratings
Peak Operation:
Recommended Fluids:
Premium quality, anti-wear
type hydraulic oil with
a viscosity of not less
than 70 SUS at operating
temperature.
31,6 [1.93] 650 21 [5.5] 25 [6.5] 50 [446] 62 [546] 83 [733] 121 [1750] 150 [2175] 190 [2756] 2,3 [5.0] 50,0 [3.00]
393
21 [5.5] 25 [6.5]
62 [549] 84 [743]
86 [765] 97 [1400]
140 [2030]
150 [2175]
2,4 [5.4]
Recommended System
Operating Temp.:
-34°C to 82°C
[-30°F to 180°F]
Recommended Filtration:
per ISO Cleanliness Code
4406, level 20/18/13
J Series (129-)
8,2 cm 3 /r [.50 in 3 /r]
Performance Data
Max.
Continuous
D Pressure Bar [PSI]
Continuous
Motors run with high
efficiency in all areas
designated with a number
for torque and speed. For
best motor life select a
motor to run with a torque
and speed range shown in
the light shaded area.
Flow LPM [GPM]
[1]
Performance data is typical
at 120 SUS. Actual data may
vary slightly from motor to
motor in production.
Max.
Continuous
Max.
Intermittent
3,8
[2]
7,6
[3]
11,4
[4.25]
Max.
Intermittent
[200]
14
[400]
28
[500]
34
[600]
41
[700]
48
[800] [1000] [1400] [1500] [2000] [2030]
55
69
97
138
140
103
[11]
1
456
[9]
1
897
[6]
1
1349
[25]
3
444
[24]
3
886
[20]
2
1331
[16]
2
1902
[16]
2
1992
[33]
4
437
[31]
4
877
[28]
3
1318
[23]
3
1885
[23]
3
1979
[40]
5
429
[38]
4
867
[35]
4
1309
[30]
3
1873
[29]
3
1964
[47]
5
422
[46]
5
860
[44]
5
1296
[36]
4
1858
[36]
4
1947
[55]
6
412
[53]
6
847
[51]
6
1285
[44]
5
1846
[43]
5
1929
[69]
8
394
[68]
8
823
[65]
7
1261
[60]
7
1817
[59]
7
1900
[96]
11
347
[97]
11
768
[94]
11
1198
[90]
10
1750
[89]
10
1833
[102]
12
332
[105]
12
749
[102]
12
1176
[97]
11
1721
[96]
11
1808
[130]
15
250
[139]
16
657
[137]
15
1070
[133]
15
1599
[131]
15
1684
[132]
15
239
[141]
16
647
[139]
16
1060
[135]
15
1585
[134]
15
1673
[146]
16
170
[163]
18
557
[164]
19
959
[160]
18
1475
[160]
18
1553
[12]
1
2458
[18]
2
2437
[26]
3
2420
[33]
4
2405
[40]
5
2387
[54]
6
2353
[83]
9
2272
[92]
10
2255
[124]
14
2134
[129]
15
2115
[154]
17
1994
Max.
Continuous
Max.
Intermittent
16,0
[4.5]
17,0
[5.5]
20,8
[2400]
165
B-1
Continuous
12,9 cm 3 /r [0.79 in 3 /r]
Intermittent
Continuous
Flow LPM [GPM]
[1]
Max.
Continuous
Max.
Intermittent
3,8
[2]
7,6
[3]
11,4
[4]
15,1
[5.5]
20,8
[6.5]
24,6
[200]
14
[400]
28
[500]
34
[600]
41
[700]
48
[800] [1000] [1400] [1450] [1500] [2000]
55
69
97
100
103
138
2030]
140
[2400]
165
[19]
2
290
[16]
2
573
[11]
1
859
[6]
1
1153
[43]
5
285
[39]
4
566
[35]
4
849
[30]
3
1140
[19]
2
1575
[54]
6
281
[51]
6
561
[47]
5
843
[41]
5
1135
[30]
3
1566
[65]
7
277
[63]
7
555
[58]
7
838
[53]
6
1129
[42]
5
1556
[76]
9
273
[74]
8
549
[70]
8
832
[64]
7
1124
[54]
6
1547
[88]
10
268
[86]
10
544
[82]
9
825
[76]
9
1117
[65]
7
1539
[109]
12
260
[109]
12
534
[105]
12
810
[99]
11
1101
[89]
10
1521
[154]
17
237
[155]
18
501
[152]
17
777
[146]
16
1060
[136]
15
1473
[159]
18
234
[160]
18
496
[157]
18
771
[152]
17
1051
[142]
16
1466
[164]
19
230
[165]
19
490
[163]
18
763
[157]
18
1044
[148]
17
1457
[214]
24
194
[221]
25
442
[219]
25
708
[214]
24
982
[205]
23
1396
[217]
25
189
[225]
25
437
[223]
25
701
[217]
25
975
[209]
24
1387
[250]
28
151
[263]
30
396
[263]
30
652
[260]
29
924
[251]
28
1330
[11]
1
1859
[23]
3
1851
[35]
4
1842
[46]
5
1831
[56]
6
1820
[81]
9
1804
[130]
15
1755
[135]
15
1743
[140]
16
1734
[198]
22
1670
[202]
23
1663
[243]
27
1599
[42] Torque [lb-in]
5 }
Nm
1556 Speed RPM
B-1-3
J Series (129-)
Performance Data
[1]
Flow LPM [GPM]
19.8 cm3/r [1.21 in3/r]
Continuous
Max.
Continuous
Max.
Intermittent
3,8
[2]
7,6
[3]
11,4
[4]
15,1
[5.5]
Max.
Max.
Contin- Interuous mittent
[200]
14
[400]
28
[500]
34
[600]
41
[700]
48
[800] [1000] [1400] [1450] [1500] [2000] [2030]
138
140
100
103
97
69
55
[2400]
165
[32]
4
189
[30]
3
379
[21]
2
569
[12]
1
761
[67]
8
187
[65]
7
375
[57]
6
565
[47]
5
758
[31]
4
1043
[85]
10
186
[83]
9
373
[75]
8
563
[65]
7
754
[49]
6
1040
[102]
12
185
[101]
11
370
[93]
11
560
[83]
9
751
[67]
8
1035
[119]
13
183
[119]
13
368
[111]
13
558
[101]
11
749
[84]
9
1033
[136]
15
182
[136]
15
366
[128]
14
556
[119]
13
746
[101]
11
1028
[170]
19
179
[172]
19
361
[163]
18
551
[154]
17
741
[137]
15
1021
[236]
27
172
[223]
25
351
[231]
26
529
[221]
25
717
[202]
23
997
[244]
28
170
[248]
28
349
[240]
27
526
[230]
26
711
[211]
24
993
[253]
29
169
[257]
29
347
[248]
28
523
[239]
27
707
[218]
25
990
[321]
36
141
[328]
37
312
[325]
37
487
[316]
36
660
[295]
33
938
[325]
37
138
[333]
38
309
[330]
37
484
[320]
36
656
[299]
34
934
[374]
42
114
[388]
44
285
[405]
46
459
[382]
43
628
[365]
41
899
[21]
2
1226
[38]
4
1222
[56]
6
1219
[74]
8
1215
[91]
10
1211
[126]
14
1204
[189]
21
1179
[196]
22
1174
[206]
23
1169
[278]
31
1121
[283]
32
1117
[347]
39
1079
20,8
[6.5]
24,6
31.6 cm3/r [1.93 in3/r]
Continuous
Continuous
Intermittent
Flow LPM [GPM]
Max.
Intermittent
[400]
28
[500]
34
[600]
41
[700]
48
[800] [1000] [1400] [1450] [1500] [1750]
100
121
103
97
69
55
[51]
6
118
[46]
5
236
[36]
4
355
[24]
3
474
[106]
12
116
[103]
12
234
[94]
11
352
[79]
9
472
[55]
6
650
[133]
15
115
[132]
15
232
[122]
14
349
[107]
12
469
[83]
9
647
[160]
18
113
[159]
18
230
[149]
17
347
[135]
15
466
[111]
13
645
[187]
21
112
[187]
21
228
[177]
20
345
[162]
18
462
[139]
16
640
[213]
24
111
[214]
24
225
[205]
23
342
[190]
21
460
[167]
19
636
[265]
30
107
[269]
30
221
[259]
29
336
[246]
28
452
[221]
25
629
[362]
41
91
[362]
41
187
[351]
40
296
[337]
38
404
[307]
35
584
[372]
42
85
[374]
42
179
[364]
41
292
[349]
39
397
[320]
36
580
[383]
43
81
[387]
44
175
[377]
43
287
[362]
41
393
[334]
38
575
[439]
50
70
[446]
50
165
[440]
50
273
[425]
48
373
[400]
45
550
[546]
62
145
[542]
61
245
[528]
60
346
[505]
57
513
[35]
4
767
[64]
7
764
[93]
11
760
[121]
14
755
[150]
17
751
[204]
23
742
[279]
32
712
[294]
33
707
[308]
35
701
[378]
43
675
[485]
55
637
3,8
[2]
7,6
[3]
11,4
[4]
15,1
[5.5]
20,8
[6.5]
24,6
50.0 cm3/r [3.00 in3/r]
Continuous
Flow LPM [GPM]
Max.
Intermittent
B-1-4
[2030]
140
[400]
28
[500]
34
[600]
41
[700]
48
[800] [1000] [1100] [1200] [1300] [1400]
83
97
90
76
69
55
[82]
9
75
[70]
8
149
[53]
6
221
[30]
3
296
[167]
19
72
[156]
18
147
[140]
16
220
[120]
14
292
[211]
24
72
[201]
23
145
[184]
21
218
[162]
18
289
[243]
28
144
[227]
26
217
[204]
23
286
[286]
32
143
[271]
31
215
[250]
28
284
[81]
9
393
[127]
14
392
[170]
19
389
[214]
24
387
[327]
37
142
[311]
35
213
[292]
33
282
[254]
29
383
[396]
45
209
[374]
42
273
[339]
38
377
[441]
50
205
[419]
47
270
[379]
43
372
[484]
55
201
[460]
52
265
[422]
48
369
[521]
59
200
[501]
57
263
[463]
52
364
[549]
62
191
[541]
61
259
[506]
57
358
[743]
84
213
[702]
79
302
[47]
5
465
[90]
10
462
[133]
15
460
[176]
20
458
[219]
25
455
[307]
35
448
[345]
39
445
[385]
43
440
[429]
48
435
[467]
53
430
[685]
77
364
3,8
[2]
7,6
[3]
11,4
[4]
15,1
[5.5]
20,8
[6.5]
24,6
[81]
9
393
Max.
Max.
[200]
14
[1]
Max.
Continuous
[2175]
150
[200]
14
[1]
Max.
Continuous
Max.
Max.
}
Torque [lb-in]
Nm
Speed RPM
J Series (129-)
Standard Rotation Viewed from Shaft End
Dimensions
Port B Pressurized — CCW 9/16
Port A Pressurized — CW
B-1
Inch End Port
9/16
-18 UNF - 2B O-Ring Ports, M14 x 1,5
- 6H O-Ring Ports — Metric Motor or
G 1/4 (BSP) Ports (2 Ports each) 4,6 [.18] Max.
B Port
X Max.
B 4,6 [.18] Max.
B Port60,2
[2.37]
Dia.
A T
B
Max.
6,4 [.25]
60,2
[2.37]
Optional External Case Drain
Dia.
T Port
(to Tank)
Max.
6,4 [.25]
3/8-24 UNF - 2B O-ring,
M10 x 1 - 6H O-ring — Metric Motor or
Optional
External Case Drain Port
G 1/8 (BSP)
(to Tank)
3/8-24 UNF - 2B O-ring,
M10 x 1 - 6H O-ring — Metric Motor or
G 1/8 (BSP)
X Max.
19,8 [.78] Max.
A Port
19,8 [.78] Max.
A Port
3/8
Inch End
Port
17,3 [.68]
A Port
A
1/4-28 UNF - 2B or M6 x 1 - 6H
12,7 [.50] Min. Deep (5)
5,6/4,6
[.22/.18]
1/4-28 UNF - 2B or M6 x 1 - 72
6H(2)
12,7 [.50] Min. Deep (5)
72 (2)
31,52/
45,08/44,83
31,42
[1.775/1.765]
[1.241/
Dia. Bolt Circle
45 (2)
1.237]
31,52/
Dia.
45,08/44,83
31,42
Pilot
[1.775/1.765]
[1.241/
End Port Dimensions
Dia. Bolt Circle
45 (2)
1.237]
DisplacementX
Dia.
cm3/r [in3/r]
mm [inch]
Pilot
8,2 [ .50]
103,9 [4.09] 12,9 [ .79]
106,9 [4.21] 19,8 [1.21]
112,5 [4.38] 31,6 [1.93]
118,9 [4.68] 50,0 [3.00]
130,3 [5.13] 4,6 [.18] Max.
34,29
[1.350]
5,6/4,6
[.22/.18]
X Max.
34,29
[1.350]
B Port
4,6 [.18] Max.
72 (2)
B Port
18,64
[.734]
33,5/31,0
[1.32/1.22]
1/4-28 UNF - 2B or M6 x 1 - 72
6H(2)
12,7 [.50] Min. Deep (5)
5,6/4,6
[.22/.18]
X Max.
17,3 [.68]
A Port
33,5/31,0
[1.32/1.22]
18,64
[.734]
1/4-28 UNF - 2B or M6 x 1 - 6H
12,7 [.50] Min. Deep (5)
5,6/4,6
[.22/.18]
60,6 [2.38]
Dia. Max.
60,6 [2.38]
Dia. Max.
Optional External Case Drain Port
(to Tank) G 1/8 (BSP)
(to Tank) G 1/8 (BSP)
31,52/
31,42
[1.241/
1.237]
31,52/
Dia.
31,42
Pilot
[1.241/
1.237]
Dia.
Pilot
45,08/44,83
[1.775/1.765]
Dia. Bolt Circle
45 (2)
45,08/44,83
[1.775/1.765]
Dia. Bolt Circle
45 (2)
End Port Dimensions
Displacement
cm3/r [in3/r]
8,2 [ .50]
12,9 [ .79]
19,8 [1.21]
31,6 [1.93]
50,0 [3.00]
160,5 [6.32]
X
mm [inch]
103,9 [4.09] 106,9 [4.21] 112,5 [4.38] 118,9 [4.68] 130,0 [5.12]
132,3 [5.21]
B-1-5
J Series (129-)
Ports Dimensions
M14 x 1,5 -6H O-Ring Ports — Metric Motor,
9/16
-18 UNF - 2B O-Ring Ports, G 3 /8 or G 1/4 (BSP) Ports (2)
Port B Pressurized — CCW
Side Port
A Port
34,39/34,19
[1.354/1.346]
17,8/16,8 [.70/.66]
Port Face
(Side Port Motors)
B Port
X Max.
Port Face
(See Detail)
64,3
[2.53]
Max.
Y
Y
A
T
7,1/6,6
[.28/.26]
1/4-28 UNF - 2B or M6 x 1 - 6H
12,7 [.50] Min. Deep (5)
72 (2)
Shaft Dim. See
Page 10 and 11
B
60,5
[2.38]
Dia.
Max.
5,6/4,6
[.22/.18]
(to Tank )
3/8-24 UNF - 2B O-ring, G 1/8 (BSP) or
M10 x 1 - 6H O-ring — Metric Motor
31,52/
31,42
[1.241/
1.237]
Dia.
Pilot
45,08/44,83
[1.775/1,765]
Dia. Bolt Circle
45 (2)
Side Port Motors
B-1-6
DisplacementX
cm3/r [in3/r]
mm [inch]
Y
mm [inch]
8,2 [ .50] 12,9 [ .79] 19,8 [1.21] 31,6 [1.93] 50,0 [3.00] 89,4/ 87,4 [3.52/3.44]
92,5/ 90,4 [3.64/3.56]
96,8/ 94,7 [3.81/3.73]
104,4/102,4 [4.11/4.03]
115,7/113,9 [4.56/4.48]
103,9 [4.09] 106,9 [4.21] 112,5 [4.38] 118,9 [4.68] 130,0 [5.12] J Series (129-)
Dimensions
Shafts
B-1
5/8
11/16
Inch Straight Keyed
4,78 [.188]
Str. Key Std . 17,996/17,717
[.7085/.6975]
Max. Torqu e
Continuous
Duty 39 Nm
[350 lb-in]
15,88/15,85
[.625/.624]
Dia. Shaft
26,2 [1.03] Max.
Coupling Length
Inch Straight Keyed
4,78 [.188]
Str. Key Std .
4,763/4,686
[.1875/.1845]
C’Bore 4 mm Deep
1/4-28 UNF - 2B
or M6 x 1 - 6H
13,0 [.51] Min. Deep
36,1/34,0 [1.42/1.34]
5/8
Inch Straight Keyed w/
Crosshole
17,475/17,450
[.6880/.6870]
Dia. Shaft
19,622/19,342
[.7725/.7615]
26,2 [1.03] Max.
Coupling Length
Max. Torqu e
Continuous
Duty 52 Nm
[465 lb-in]
3/4
4,763/4,686
[.1875/.1845]
C’Bore 4 mm Deep
1/4-28 UNF - 2B
13,0 [.51] Min.
Deep
36,1/34,0 [1.42/1.34]
Inch Tapered (Tapered Shaft End Per SAE J744 Except as Specified — 1.5 : 12 Ratio) 4,82/4,75 [.190/.187] Dia. Thru
4,76 x 15,75 [.188 x .620]
Woodruff Ke y
3,20 [.126]
Dia. Thru
10,2/9,7 [.40/.38]
4,788/4,762
[.1885/.1875]
19,0 [.75] Dia.
15,88/15,85
[.625/.624]
Dia. Shaft
26,2 [1.03] Max. Coupling Length
36,1/34,0 [1.42/1.34]
Max. Torqu e
Continuous
Duty 39 Nm
[350 lb-in]
8,9/7,1
[.35/.28]
Max. Torqu e
Continuous
Duty 68 Nm
[600 lb-in]
Max.
Coupling
24,6
Width
[.97]
2,52/2,26
[.099/.089]
1/2-20 UNF - 2A Slotted Hex. Nut
11,2 [.44] Thick 18,87 [.743] Across Flats
Recommended Torque :
6,2 Nm [55 lb-in] Dry
4,5 Nm [40 lb-in] Lub.
50,8/49,3 [2.00/1.94]
B-1-7
J Series (129-)
Dimensions
Shafts and Flange Kit
16 mm Straight Keyed
5x5x18
Straight Key
Max. Torqu e
Continuous
Duty 39 Nm
[350 lb-in]
18 mm Straight Keyed
18,000/17,959
[.7087/.7070]
6x6x18
Straight Key
5,00/4,97
[.1969/.1957]
16,000/15,974
[.6299/.6289]
C’Bore 4 mm Deep
Dia. Shaft
M6 x 1 - 6H
26,2 [1.03] Max. 13,0 [.51] Min. Deep
Coupling Length
36,1/34,0 [1.42/1.34]
Involute 9T Splined — Metric
Involute
Splined Shaft
External
B17x14 DIN 5482
18,001/17,975
[.7087/.7076]
Dia. Shaft
20,501/20,369
[.8071/.8019]
Max. Torqu e
Continuous
Duty 58 Nm
[510 lb-in]
6,00/5,97
[.236/.235]
C’Bore 4 mm Deep
M6 x 1 - 6H
13,0 [.51] Min. Deep
26,2 [1.03] Max.
Coupling Length
36,1/34,0 [1.42/1.34]
2 Bolt Flange Kits (2)
16,51/16,48
[.650/.649]
Dia. Shaft
72,9
[2.87]
63,04/62,94
[2.482/2.478]
Dia.
C’Bore 4 mm Deep
M6 x 1 - 6H
13,0 [.51] Min. Deep
14,0 [.55] Max. Coupling Length
Max. Torqu e
Continuous
Duty 44 Nm
[390 lb-in]
36,1/34,0 [1.42/1.34]
5,61/5,36
[.221/.211]
2,24/1,83
[.088/.072]
5,61/5,36
[.221/.211]
See Dim.(s)
in Note
Below
80,26/79,76
[3.160/3.140]
97,3/96,8
[3.83/3.81]
Note:
Kit 60552 for 3/8 Dia.
Mounting Bolts (10,49/10,24
[.413/.403] Dia. Thru) 1/4-28
UNF screws for attaching
flange to motor (5)
Kit 60553 for M8 Dia.
Mounting Bolts (9,12/8,86
[.359/.349] Dia. Thru) M6 x
1 -6H screws for attaching
flange to motor (5)
B-1-8
J Series (129-)
Use digit prefix —
129- plus four digit number
from charts for complete
product number—
Example 129-0479.
Product Numbers
Orders will not be accepted
without three digit prefix.
End Port
Mounting Shaft Port Size 1/4-28 UNF 2B
M6 x 1 - 6H
5/8
inch Straight inch Straight Splined — Metric 3/4 inch Tapered 16 mm Straight 18 mm Straight Splined — Metric 16 mm Straight 18 mm Straight Splined — Metric 16 mm Straight 18 mm Straight Splined — Metric 11/16
9/16 -18
UNF
2B O-Ring (2)
M14 x 1,5 6H O-Ring (2)
G 1/4 (BSP) (2)
G 3/8 (BSP) (2)*
Displ. cm3/ r [in3/ r] / Product Number
8,2 [ .50] 12,9 [ .79] 19,8 [1.21] 31,6
[1.93] 50,0
[3.00]
129-0291 129-0295 129-0299 129-0480
129-0303 129-0307 129-0311 129-0315 129-0319 129-0323 129-0327 129-0331 129-0335 -0292 -0296 -0300 -0293 -0297 -0301 -0294 -0298 -0302 -0458
-0459
-0460
-0304 -0308 -0312 -0316 -0320 -0324 -0328 -0332 -0336 -0305 -0309 -0313 -0317 -0321 -0325 -0329 -0333 -0337 -0306 -0310 -0314 -0318 -0322 -0326 -0330 -0334 -0338 -0461
-0462
-0463
-0464
-0465
-0466
-0467
-0468
-0469
*Note: The Same Casting used for Side Ports is Required for G 3/8 (BSP) End Ports
129-0336
Side Port
Mounting Shaft Port Size 1/4-28 UNF 2B
M6 x 1 - 6H
5/8
inch Straight inch Straight Splined — Metric 3/4 inch Tapered 16 mm Straight 18 mm Straight Splined — Metric 16 mm Straight 18 mm Straight
Splined — Metric 16 mm Straight 18 mm Straight Splined — Metric 11/16
9/16 -18
UNF
2B O-Ring (2)
M14 x 1,5 6H O-Ring (2)
8,2 [ .50] 12,9 [ .79] 19,8 [1.21] 31,6
[1.93] 50,0
[3.00]
129-0339 129-0343 129-0347 129-0481
129-0351 129-0355 129-0359 129-0363 -0340 -0344 -0348 -0341 -0345 -0349 -0342 -0346 -0350 -0470
-0471
-0472
-0352 -0356 -0360 -0364 -0353 -0357 -0361 -0365 -0354 -0358 -0362 -0366 -0473
-0474
-0475
-0476
129-0367 129-0371 129-0375 129-0379 -0368 -0372 -0376 -0380 -0369 -0373 -0377 -0381 -0370 -0374 -0378 -0382 -0477
-0403
-0478
-0479
G 1/4 (BSP) (2)
G 3/8 (BSP) (2)
Two Bolt Mounting Flange Kit (for 3/8 inch Mounting Bolts) — Kit Number 60552 (includes 5 screws — 1/4 -28 UNF-2B)
Two Bolt Mounting Flange Kit (for M8 Mounting Bolts ) — Kit Number 60553 (includes 5 screws — M6 x 1-6H)
B-1-9
B-1
J Series (129-)
The hydrodynamic bearing
has infinite life when
shaft load ratings are not
exceeded. Hence, the shaft
side load capacity is more
than adequate to handle
most externally applied
loads (such as belts, chains,
etc.), providing the motor to
shaft size is applied within
its torque rating.
side or radial loads being
applied to shaft at locations
A, B, and C, to determine
the shaft side load capacity
at locations other than those
shown use the formula
(shown below). For more
information about shaft side
loads on Char-Lynn motors
contact your Eaton representative.
Allowable Side Load — kg [lb] Allowable side load chart,
shaft load location drawing
(right) and load curves
(below) are based on the
196 [432]
200
[400]
163 [360]
150
[300]
132 [291]
100
Shaft
Side
Load
kg
50
[lb]
0
B-1-10
RPM A
B
C
2300
1500
1250
1000
750
600 500 400 340 29 [ 64]
44 [ 98]
54 [118]
67 [147]
89 [196]
111 [245]
133 [294] 167 [368] 196 [432] 24 [ 53]
37 [ 82]
44 [ 98]
55 [122]
74 [163]
93 [204]
111 [245]
139 [306] 163 [360] 20 [ 43]
30 [ 66]
36 [ 79]
45 [ 99]
60 [132]
75 [165]
90 [198]
112 [248]
132 [291]
2300
L + 42
A
Sideload P kg =
1500
N
(
B
Sideload P [lb] =
1500
N
200
( L + [1.66] )
C
)
L
Where N = Shaft Speed (RPM)
L = Distance from Mounting Surface
34,8 [1.37]
20,1 [ .79]
9,7 [ .38]
P
[200]
C
B A
[100]
0
0
0
Speed (RPM)
340 500
1000
1500
2000
2500
Mounting
Surface
J Series (129-)
Case Pressure and Case Drain
B-1
The J Series now offers check
valves in the motor as a
standard feature. This addition
reduces the case pressure
in the motor to the return
pressure of the system when
the case drain is not used.
For return pressures higher
than the rated pressures (see
chart) the external case drain
can be connected. If the case
drain line is needed, connect
drain line to assure that the
motor will always remain full
of fluid.
Case Drain Advantage
Example:
Note:
In addition to providing
lower case pressures for
motors connected in series,
there are advantages for
adding an external case
drain line to motors with
normal case pressures as
well. These advantages are:
A 14 Bar case pressure will
cause a load of 40 kg, so
the allowable thrust load will
be 82 kg plus 40 = 120 kg
kg pushing inward on shaft.
Tension load is 82 kg under
all case pressure conditions.
J Series motors can be
connected in parallel or in
series.
Contamination Control —
flushing the motor case.
Motor Cooler — exiting oil
draws motor heat away.
Extend Motor Seal Life —
maintain low case pressure
with a preset restriction
installed in the case drain line
Example:
A 200 PSI case pressure will
cause a load of 88 lbs, so
the allowable thrust load will
be 180 lbs plus 88 = 268
lbs pushing inward on shaft.
Tension load is 180 lb under
all case pressure conditions
Case pressure will add to
the allowable compressive
thrust load. Case pressure
will push outward on the
shaft at 20 kg/7 Bar [44
lb/100 PSI]. P1
Pc
Thrust Load
P2
P1
Pc
Thrust Load
Max. Axial Loads
82 kg [180 lb] *
Max. Axial Loads
82 kg [180 lb] *
Case
Pressure
Bar
[PSI] 100
[1500]
Case Drain
Required
Case
76
Pressure
[1100]
[1000]
Bar
Intermittent
[1500] —
Case D
[PSI] 100 Case
Drain
50
Require
Optional
[500]
Continuous
76 —
Case [1100]
Drain
[1000]
In
Optional
50
0
0
0
0
500
1000 [500]
1500
2000
Continuous —
Speed RPM
Case Drain
Optional
Case Pressure Seal Limitation
0
0
0
0
500
100
Speed R
B-1-11
J Series (129-)
The following 16-digit coding system has been developed
to identify all of the configuration options for the J motor.
Use this model code to specify a motor with the desired
features. All 16-digits of the code must be present when
ordering. You may want to photocopy the matrix below to
ensure that each number is entered in the correct box.
Model Code
1
M
0 J
* *
1
2 3
4 5
Product
6
* *
7 8
7 , 8 Output Shaft
01 – 5/8 inch Dia. Straight
with 4,72 [.186] Square
Key and 1/4-28 UNF - 2B
Threaded Hole
M – Motor
2 , 3 Series
0J – J Series
4 , 5 Displacement
cm3/r [in3/r]
05 – 8,2 [ .50]
08 – 12,9 [ .79]
12 – 19,8 [1.21]
19 – 31,6 [1.93]
30 – 50,0 [3.00]
6 Mounting Type
A – 5 Bolt: Dia. 31,47
[1.239] x 5,1 [.20] Pilot 1/4-28
UNF 2B Mounting Holes on
45 [1.77] Dia. Bolt Circle
B – 5 Bolt: Dia. 31,47 [1.239]
x 5,1 [.20] Pilot M6 x 1- 6H
Mounting Holes on 45 [1.77]
Dia. Bolt Circle
C – 2 Bolt: Dia. 62,99 [2.480]
x 2,0 [.08] Pilot 10,36[.408]
Mounting Holes on 80,0
[3.150] Dia. Bolt Circle
D – 2 Bolt: Dia. 62,99
[2.480] x 2,0 [.08] Pilot 9,0
[.354] Mounting Holes on
80,0 [3.150] Dia. Bolt Circle
B-1-12
*
02 – 16 mm Dia. Straight
with 5,00 [.197] Square Key
with M6 x 1 - 6H Threaded
Hole
with 4,72 [.186] Square
Key and 1/4-28 UNF - 2B
Threaded Hole
with 5,92 [.233] Square Key
with M6 x 1 - 6H Threaded
Hole
06 – Involute Splined 9T—
Metric 16,50 [.650] Dia. (B17
x 14 DIN 5482) M6 x 1 - 6H
Threaded Hole
*
9
*
10
0 0
11
*
*
0
B
12 13
14
15
16
9 Ports
A – 9/16 -18 UNF - 2B O-Ring
End Ported
B–G
1/4
(BSP) End Ported
C – M14 x 1,5 - 6H O-Ring
Port, End Ported
D – 9/16 -18 UNF - 2B O-Ring
Side Ported
E – G 3 /8 (BSP) Side Ported
11 , 12 Special Features
(Hardware)
00 – None
Features
13 Special
(Assembly)
0 – None
1 – Reverse Rotation
F – G 1/4 (BSP) Side Ported
14 Paint/Special
Packaging
H – G 3 /8 (BSP) End Ported
0 – No Paint, Individual Box
10 Case Flow Options
A – Low Gloss Black Primer,
Individual Box
0 – No Case Drain
1 – 3 /8 -24 UNF - 2B O-Ring
2 – G 1/8 (BSP)
3 – M10 x 1 - 6H O-Ring
with 4,75 [.187] Dia.
Crosshole
08 – 3 /4 inch Tapered with
Woodruff Key and Nut
with 4,72 [.186] Sq. Key with
1/4-28 UNF -2B Threaded
Hole (Plated for Corrosion
Protection)
with 5,00 [.197] Sq. Key
with M6 x 1- 6H Threaded
Hole (Plated for Corrosion
Protection)
B – No Paint, Bulk Box
Option
15 Eaton Assigned
Code when Applicable
0 – Assigned Code
Assigned
16 Eaton
Design Code
B – Assigned Design Code
H Series (101-)
Features:
• Time-tested Char-Lynn
drive set
Highlights
Motor Shaft Drive
• Three moving components (gerotor-star,
drive, and shaft)
Gerotor Star
• Optimized drive
running angle
Port B
• Three-zone pressure
design (inlet, return
and case)
Port A
B-2
shafts and mounts
• Special options to meet
customer needs
Benefits:
• High efficiency
• Powerful compact
package
Description
Designed for medium duty applications, these motors use
industry-proven spool valve technology combined with stateof-the-art gerotors. In addition, a wide variety of mounting
flanges, shafts, Ports and valving options provide design
flexibility. Direction of shaft rotation and shaft speed can
be controlled easily and smoothly throughout the speed
range of the motor, and equipment can be driven direct,
eliminating costly mechanical components.
performance
Applications:
harvesters, seeders
• Car wash brushes
• Food processing
equipment
• Machine tools
Specifications
Gerotor Element
Flow l/min [GPM]
13 Displacements
57 [15] Continuous***
76 [20] Intermittent**
Speed
Up to 1100 RPM
Pressure bar [PSI]
125 [1800] Cont.***
165 [2400] Inter.**
Torque Nm [lb-in]
407 [3604] Cont.***
520 [4600] Inter.**
• Conveyors
floor polishers
• Saw mill works
• Turf equipment
• Concrete and asphalt
equipment
• Skid steer attachments
• Many more
Conveyer
Combine
Sweeper
Salt and Sand Spreader
B-2-1
H Series (101-)
Specifications
Thrust
Needle Bearing
Static
Seal
Housing
Drive
Cap Screws
Static Seals
Spacer Plate
Gerotor
Thrust
Bearing
Race
Backup
Washer
Output
Shaft
Exclusion
Seal
Pressure Seal
Flange
End Cap
View of Gerotor Section
Specification Data — H Motors
Displ. cm3/r [in3/r] 36 46 59 74 97 120146159185231293370739
[2.2] [2.8]
[3.6]
[4.5]
[5.9]
[7.3]
[8.9]
[9.7]
[11.3] [14.1] [17.9] [22.6][45.1]
Max. Speed (RPM) 102196995376058546938535330424319215274
@ Continuous Flow
Flow LPM Continuous 38 [10] 45 [12] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15]
[GPM]
Intermittent 38 [10] 53 [14] 64 [17] 68 [18] 68 [18] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20]
TorqueContinuous
56 73 91 118155192221233265302351407389
Nm [lb-in]
[497] [650] [802] [1044][1368][1699][1954][2059][2343][2669][3110][3604][3440]
Intermittent
75 99 122158207257300319356415466484520
[668] [876] [1076][1401][1829][2278][2653][2824][3151][3671][4121][4283][4600]
Min.
@ Cont. Pressure 46
59
76
95
124
154
176
186
211
238
282
330
316
Starting
[410] [520] [670] [840] [1100][1360][1560][1650][1870][2110][2500][2920][2800]
Torque @ Int. Pressure
63 81 104130171210246 262]293339388408434
Nm [lb-in]
[560]
[720]
[920]
[1150][1510] [1860][2180] [2320
[2590][3000][3430] [3610][3840]
Pressure
Continuous
12412412412412412411711411010093 86 41
∆Bar
[1800][1800][1800][1800][1800][1800][1700][1650][1600][1450][1350][1250][600]
16516516516516516515915514813812410355
[∆ PSI]Intermittent
[2400][2400][2400][2400][2400][2400][2300][2250][2150][2000][1800][1500][800]
End Ported Units Only
∆ BarCont. Pressure
83837676766969696255485727
[∆ PSI]
[1200][1200][1100][1100][1100][1000][1000][1000][900] [800] [700] [825] [396]
Intermittent
11711711011011010310310391 90 83 68 36
[1700][1700][1600][1600][1600][1500][1500][1500][1400][1300][1200][990] [528]
Weight kg [lb] 5,15,15,25,25,45,55,65,75,86,06,36,78,4
[11.2][11.2][11.5][11.5][11.8][12.1][12.4][12.5][12.8][13.3][14.0][14.7][18,6]
A simultaneous maximum Maximum Inlet Pressure:
torque and maximum
172 Bar [2500 PSI] without
speed NOT recommended. regard to ∆ Bar [∆ PSI] and/
Note:
To assure best motor life, run
motor for approximately one
hour at 30% of rated pressure
before application to full
load. Be sure motor is filled
with fluid prior to any load
applications.
6B splined or Tapered
shafts are recommended
whenever operation above
282 NM [2500 lb-in] of
torque, especially for those
frequent reversals.
Δ Pressure:
Recommended Fluids:
The true Δ bar [Δ PSI]
difference between inlet
port and outlet port
Recommended Fluids —
type hydraulic oil. Minimum
oil viscosity (at operating
temperature) should be the
highest of the following:
100 SUS or
300 x Bar = SUS
RPM
Continuous Rating:
Motor may be run
10% of every minute
Note:
∆ pressure is derated for
end ported units.
B-2-2
20 x PSI = SUS
RPM
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
4406, level 20/18/13
H Series (101-)
36 cm 3/r [2.2 in 3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800]
55
69
83
110
97
124
[49]
6
204
[47]
5
408
[44]
5
613
[40]
5
817
[36]
4
1021
[103]
12
201
[106]
12
407
[102]
12
612
[97]
11
817
[90]
10
1021
[162]
18
198
[160]
18
402
[158]
18
609
[153]
17
814
[148]
17
1015
[189]
21
194
[191]
22
399
[188]
21
604
[184]
21
807
[180]
20
1008
∆ Pressure Bar [PSI]
Performance Data
at 120 SUS. Actual data
may vary slightly from unit
to unit in production.
[2]
Flow LPM [GPM]
for torque and speed,
however for best motor
life select a motor to run with
a torque and speed range
printed in the light shaded
area.
Max.
Continuous
7,6
[4]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[90]
10
1021
Continuous
[270]
31
189
[274]
31
394
[272]
31
599
[270]
31
799
[265]
30
1001
[325]
37
184
[327]
37
387
[328]
37
591
[326]
37
793
[322]
36
991
[379]
43
177
[384]
43
381
[383]
43
586
[383]
43
785
[380]
43
981
[432]
49
170
[439]
50
373
[440]
50
576
[440]
50
776
[438]
49
969
Max.
Intermittent
[2400]
165
[489]
55
162
[495]
56
365
[496]
56
565
[497]
56
762
[495]
56
959
[650]
73
122
[654]
74
323
[661]
75
523
[668]
75
721
[664]
75
920
Max.
Intermittent
[2400]
165
B-2
}
Torque [lb-in ]
Nm
Speed RPM
Intermittent
46 cm 3/r [2.8 in 3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800]
55
69
83
110
97
124
[64]
7
161
[61]
7
323
[58]
7
486
[52]
6
648
[47]
5
808
[36]
4
969
[136]
15
158
[139]
16
320
[134]
15
481
[128]
14
643
[118]
13
803
[109]
12
964
[212]
24
156
[209]
24
316
[207]
23
479
[200]
23
640
[194]
22
798
[188]
21
960
[284]
32
153
[286]
32
314
[282]
32
475
[276]
31
635
[269]
30
793
[260]
29
952
[355]
40
148
[359]
41
310
[356]
40
471
[354]
40
628
[347]
39
787
[340]
38
946
[426]
48
145
[429]
48
304
[430]
49
464
[428]
48
623
[423]
48
779
[417]
47
938
[497]
56
139
[503]
57
300
[502]
57
461
[502]
57
617
[498]
56
771
[492]
56
931
[567]
64
133
[576]
65
293
[577]
65
453
[577]
65
610
[575]
65
761
[567]
64
922
[641]
72
127
[649]
73
287
[650]
73
444
[651]
74
599
[649]
73
753
[643]
73
914
[25]
3
1127
[98]
11
1123
[175]
20
1115
[249]
28
1108
[327]
37
1100
[404]
46
1093
[484]
55
1086
[559]
63
1079
[634]
72
1068
[2]
Flow LPM [GPM]
7,6
[4]
Max.
Continuous
Max.
Intermittent
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
53,0
[852]
96
95
[857]
97
253
[867]
98
410
[876]
99
566
[871]
98
722
[864]
98
877
B-2-3
H Series (101-)
Performance Data
59 cm 3/r [3.6 in 3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800]
97
55
69
83
110
124
[79]
9
127
[76]
9
254
[73]
8
381
[64]
7
508
[57]
6
635
[45]
5
762
[33]
4
889
[29]
3
953
[169]
19
125
[168]
19
254
[161]
18
381
[151]
17
508
[141]
16
635
[131]
15
762
[118]
13
889
[111]
13
953
[260]
29
123
[257]
29
251
[252]
28
380
[243]
27
508
[234]
26
634
[227]
26
762
[213]
24
887
[205]
23
951
[305]
34
121
[307]
35
249
[303]
34
377
[294]
33
504
[283]
32
630
[274]
31
757
[266]
30
882
[260]
29
945
[437]
49
117
[441]
50
246
[439]
50
373
[428]
48
500
[419]
47
626
[409]
46
753
[396]
45
877
[389]
44
940
[526]
59
114
[529]
60
241
[529]
60
368
[519]
59
496
[512]
58
621
[505]
57
747
[492]
56
872
[486]
55
935
[616]
70
109
[620]
70
236
[618]
70
364
[609]
69
491
[602]
68
614
[593]
67
741
[583]
66
866
[576]
65
929
[704]
80
103
[710]
80
230
[709]
80
358
[701]
79
484
[693]
78
608
[684]
77
734
[676]
76
860
[670]
76
921
[796]
90
96
[800]
90
224
[802]
91
349
[794]
90
476
[786]
89
601
[778]
88
728
[770]
87
851
[765]
86
913
[17]
2
1080
[98]
11
1080
[192]
22
1077
[252]
28
1071
[377]
43
1067
[475]
54
1062
[567]
64
1055
[660]
75
1049
[757]
86
1040
area.
15,1
[6]
Flow LPM [GPM]
[2]
7,6
[4]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Continuous
Intermittent
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[20]
75,7
Max.
Intermittent
[2400]
165
[1055]
119
65
[1065]
120
193
[1069]
121
319
[1076]
122
446
[1071]
121
571
[1058]
120
694
[1055]
119
813
[1055]
119
872
}
[111] Torque [lb-in ]
13
Nm
953 Speed RPM
74 cm 3/r [4.5 in 3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800]
97
55
69
83
110
124
[103]
12
101
[99]
11
203
[94]
11
305
[86]
10
406
[74]
8
507
[58]
7
608
[43]
5
709
[36]
4
760
[220]
25
99
[219]
25
201
[210]
24
303
[196]
22
404
[183]
21
505
[171]
19
606
[154]
17
706
[145]
16
757
[339]
38
98
[335]
38
199
[328]
37
301
[319]
36
402
[310]
35
502
[295]
33
603
[277]
31
702
[268]
30
753
[454]
51
96
[457]
52
197
[451]
51
298
[438]
49
399
[422]
48
499
[408]
46
600
[396]
45
698
[387]
44
749
[569]
64
93
[574]
65
194
[571]
65
296
[558]
63
396
[545]
62
496
[533]
60
596
[515]
58
694
[506]
57
744
[685]
77
90
[689]
78
191
[689]
78
292
[676]
76
393
[667]
75
492
[657]
74
591
[640]
72
691
[632]
71
740
[801]
91
86
[808]
91
187
[805]
91
288
[793]
90
388
[784]
89
486
[773]
87
587
[760]
86
686
[750]
85
735
[916]
103
81
[925]
105
182
[924]
104
283
[913]
103
383
[903]
102
482
[891]
101
581
[880]
99
681
[873]
99
729
[1036]
117
76
[1042]
118
177
[1044]
118
276
[1033]
117
377
[1024]
116
476
[1013]
114
576
[1002]
113
674
[996]
113
723
[14]
2
904
[121]
14
902
[233]
26
898
[351]
40
895
[482]
54
891
[609]
69
887
[725]
82
882
[856]
97
877
[981]
111
869
[2]
7,6
[4]
Flow LPM [GPM]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Max.
Continuous
Max.
Intermittent
B-2-4
53,0
[15]
56,8
[20]
75,7
Max.
Intermittent
[2400]
165
[1373]
155
51
[1386]
157
153
[1392]
157
252
[1401]
158
352
[1394]
158
452
[1377]
156
549
[1374]
155
643
[1373]
155
690
H Series (101-)
97 cm 3/r [5.9 in 3/r]
Performance Data
area.
[2]
7,6
[4]
15,1
[6]
Flow LPM [GPM]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Intermittent
Max.
Continuous
Max.
Intermittent
[400]
28
[600]
41
[134]
15
78
[131]
15
156
[126]
14
234
[110]
12
312
[96]
11
390
[77]
9
468
[60]
7
546
[52]
6
585
[292]
33
76
[281]
32
155
[269]
30
233
[246]
28
311
[231]
26
389
[218]
25
467
[197]
22
544
[189]
21
583
[442]
50
75
[436]
49
153
[425]
48
231
[408]
46
310
[392]
44
387
[378]
43
465
[358]
40
542
[346]
39
581
[593]
67
73
[596]
67
151
[588]
66
230
[566]
64
308
[539]
61
385
[522]
59
463
[513]
58
539
[495]
56
578
[746]
84
71
[750]
85
149
[747]
84
228
[718]
81
305
[699]
79
383
[681]
77
460
[662]
75
537
[651]
74
575
[899]
102
68
[903]
102
147
[900]
102
224
[873]
99
303
[859]
97
380
[844]
95
457
[828]
94
535
[819]
93
573
53,0
[15]
56,8
[20]
[25]
3
701
[157]
18
700
[311]
35
697
[455]
51
694
[625]
71
691
[790]
89
688
75,7
[1054]
119
65
[1059]
120
143
[1054]
119
221
[1023]
116
300
[1005]
114
376
[990]
112
453
[973]
110
531
[963]
109
569
[1209]
137
61
[1212]
137
139
[1206]
136
217
[1177]
133
295
[1156]
131
373
[1142]
129
449
[1131]
128
526
[1126]
127
564
[1365]
154
55
[1367]
154
134
[1368]
155
210
[1339]
151
291
[1318]
149
368
[1301]
147
445
[1293]
146
521
[1286]
145
559
Max.
Intermittent
[2400]
165
[1806]
204
33
[1828]
207
113
[1823]
206
189
[1829]
207
269
[1821]
206
346
[1792]
202
421
[1776]
201
499
[1778]
201
536
B-2
[941] [1110] [1272]
106
144
125
684
674
681
}
[189] Torque [lb-in ]
21
Nm
583 Speed RPM
120 cm 3/r [7.3 in 3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800]
97
124
55
69
83
110
[162]
18
62
[160]
18
125
[155]
18
188
[139]
16
250
[121]
14
313
[102]
12
375
[78]
9
438
[67]
8
469
[357]
40
61
[348]
39
124
[338]
38
187
[319]
36
250
[303]
34
312
[288]
33
374
[263]
30
437
[253]
29
468
[544]
61
61
[539]
61
123
[530]
60
186
[515]
58
249
[497]
56
311
[480]
54
373
[458]
52
435
[446]
50
466
[736]
83
59
[736]
83
121
[729]
82
185
[710]
80
247
[686]
78
309
[664]
75
371
[652]
74
433
[632]
71
464
[927]
105
58
[930]
105
120
[923]
104
183
[901]
102
245
[883]
100
308
[862]
97
370
[841]
95
431
[828]
94
462
[20]
2
626
[202]
23
624
[384]
43
621
[581]
66
618
[778]
88
617
[2]
7,6
[4]
15,1
[6]
Flow LPM [GPM]
Continuous
[200]
14
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800]
55
69
83
110
97
124
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[20]
75,7
[1116]
126
55
[1119]
126
119
[1116]
126
180
[1094]
124
243
[1081]
122
306
[1060]
120
367
[1041]
118
430
[1030]
116
460
[1305]
147
53
[1316]
149
116
[1310]
148
178
[1283]
145
241
[1267]
143
302
[1246]
141
365
[1228]
139
427
[1214]
137
458
[1498]
169
49
[1506]
170
114
[1500]
169
175
[1476]
167
237
[1460]
165
300
[1440]
163
361
[1420]
160
423
[1411]
159
454
[1687]
191
45
[1698]
192
110
[1699]
192
170
[1673]
189
233
[1655]
187
296
[1640]
185
358
[1616]
183
419
[1608]
182
450
Max.
Intermittent
[2400]
165
[2231]
252
26
[2268]
256
90
[2271]
257
152
[2278]
257
216
[2268]
256
278
[2232]
252
338
[2213]
250
401
[2205]
249
430
[971] [1169] [1356] [1559]
110
153
132
176
614
609
611
606
B-2-5
H Series (101-)
Performance Data
146 cm3/r [8.9 in3/r]
area.
[2]
7,6
[4]
15,1
[6]
Flow LPM [GPM]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Continuous
Intermittent
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1700]
97
55
69
83
110
117
[198]
22
51
[196]
22
103
[189]
21
154
[169]
19
205
[148]
17
257
[125]
14
308
[95]
11
359
[82]
9
85
[435]
49
50
[424]
48
102
[412]
47
153
[389]
44
205
[369]
42
256
[351]
40
307
[321]
36
358
[308]
35
384
[664]
75
50
[657]
74
101
[646]
73
152
[628]
71
204
[605]
68
255
[586]
66
306
[558]
63
357
[544]
61
383
[897]
101
49
[898]
101
99
[889]
100
151
[866]
98
203
[836]
94
253
[810]
92
305
[795]
90
355
[771]
87
381
[24]
3
513
[246]
28
512
[468]
53
509
[708]
80
507
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[20]
75,7
[1130]
128
47
[1133]
128
99
[1125]
127
150
[1098]
124
201
[1076]
122
252
[1051]
119
303
[1026]
116
354
[1010]
114
379
[1361]
154
45
[1365]
154
97
[1361]
154
148
[1333]
151
200
[1318]
149
251
[1293]
146
301
[1290]
146
352
[1256]
142
378
[1591]
180
43
[1604]
181
95
[1598]
181
146
[1564]
177
197
[1544]
174
248
[1519]
172
299
[1497]
169
350
[1480]
167
375
[1827]
206
40
[1836]
207
93
[1829]
207
143
[1799]
203
195
[1780]
201
246
[1756]
198
296
[1731]
196
347
[1720]
194
373
[1942]
219
39
[1954]
221
92
[1951]
220
141
[1919]
217
193
[1899]
215
244
[1878]
212
295
[1851]
209
346
[1840]
208
371
159 cm3/r [9.7 in3/r]
7,6
[4]
Flow LPM [GPM]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[20]
75,7
[359]
41
352
B-2-6
}
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1650]
55
69
83
97
110
134
[209]
24
47
[210]
24
94
[205]
23
141
[186]
21
188
[164]
19
235
[144]
16
282
[109]
12
330
[92]
10
353
[465]
53
46
[460]
52
94
[454]
51
141
[440]
50
188
[422]
48
234
[404]
46
281
[374]
42
329
[359]
41
352
[715]
81
46
[710]
80
93
[704]
80
140
[693]
78
187
[671]
76
234
[652]
74
281
[623]
70
328
[612]
69
351
[973]
110
45
[971]
110
91
[965]
109
139
[951]
107
186
[930]
105
232
[900]
102
279
[883]
100
327
[861]
97
350
[26]
3
471
[268]
30
470
[510]
58
467
[772] [1034] [1290] [1553] [1802] [1865]
87
117
146
175
211
204
465
464
462
460
458
458
Torque [lb-in]
Nm
Speed RPM
[2611]
295
24
[2648]
299
78
[2653]
300
128
[2649]
299
180
[2789]
315
231
[2606]
294
281
[2580]
292
331
[2569]
290
356
[948] [1184] [1425] [1653] [1780]
134
107
161
201
187
504
506
501
498
499
[2]
Max.
Intermittent
[2300]
159
[1228]
139
44
[1229]
139
91
[1216]
137
138
[1205]
136
185
[1189]
134
232
[1163]
131
279
[1140]
129
325
[1123]
127
348
[1478]
167
42
[1480]
167
90
[1477]
167
136
[1461]
165
183
[1451]
164
230
[1421]
161
277
[1396]
158
323
[1381]
156
347
[1724]
195
40
[1745]
197
89
[1738]
196
134
[1716]
194
181
[1702]
192
228
[1674]
189
275
[1653]
187
322
[1633]
185
345
[1981]
224
38
[1996]
226
87
[1991]
225
132
[1973]
223
179
[1965]
219
226
[1937]
219
273
[1900]
215
319
[1886]
213
343
[2046]
231
37
[2059]
233
87
[2055]
232
132
[2038]
230
178
[2032]
230
225
[2004]
226
272
[1963]
222
319
[1950]
220
342
Max.
Intermittent
[2250]
155
[2764]
312
23
[2813]
318
76
[2824]
319
119
[2808]
317
166
[2789]
315
213
[2770]
313
260
[2727]
308
306
[2712]
306
330
H Series (101-)
Performance Data
185 cm3/r [11.3 in3/r]
[200]
14
[400]
28
Max.
ContinContinuous
uous
[600] [800] [1000] [1200] [1400] [1600]
41
55
69
83
110
97
[257]
29
40
[254]
29
81
[246]
28
121
[224]
25
162
[202]
23
202
[176]
20
243
[140]
16
283
[120]
14
304
[554]
63
40
[546]
62
81
[540]
61
121
[520]
59
162
[499]
56
202
[475]
54
242
[443]
50
283
[425]
48
303
[847]
96
39
[845]
95
80
[834]
94
120
[820]
93
161
[793]
90
201
[767]
87
242
[735]
83
282
[719]
81
302
[27]
3
405
[321]
36
404
[612]
69
402
area.
7,6
[4]
15,1
[6]
Flow LPM [GPM]
[2]
30,3
[10]
37,9
[12]
45,4
[14]
Continuous
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[20]
75,7
[1447]
163
37
[1448]
164
78
[1434]
162
119
[1414]
160
159
[1394]
158
200
[1368]
155
240
[1340]
151
280
[1320]
149
300
[1739]
196
36
[1744]
197
77
[1736]
196
117
[1716]
194
157
[1699]
192
198
[1664]
188
238
[1637]
185
279
[1618]
183
299
[2035]
230
33
[2049]
232
76
[2036]
230
115
[2014]
228
155
[1997]
226
196
[1969]
222
236
[1936]
219
277
[1914]
216
297
[2320]
262
29
[2343]
265
74
[2337]
264
112
[2315]
262
152
[2299]
260
193
[2268]
256
234
[2227]
252
274
[2205]
249
294
231 cm3/r [14.1 in3/r]
[2]
7,6
[4]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[200]
14
[400]
28
[338]
38
32
[328]
37
65
[317]
36
97
[289]
33
130
[265]
30
162
[230]
26
195
[191]
22
227
[167]
19
243
[707]
80
32
[695]
79
65
[687]
78
97
[659]
74
130
[631]
71
162
[599]
68
195
[563]
64
227
[538]
61
243
Max.
ContinContinuous
uous
[600] [800] [1000] [1200] [1400] [1450]
41
55
69
83
100
97
[29]
3
324
[411]
46
324
[20]
75,7
[538]
61
243
[1074]
121
31
[1076]
122
64
[1057]
119
97
[1038]
117
130
[1004]
113
162
[968]
109
194
[927]
105
227
[904]
102
243
[3103]
351
12
[3147]
356
63
[3151]
356
100
[3133]
354
140
[3112]
352
181
[3088]
349
222
[3051]
345
262
[3023]
342
283
B-2
[911] [1211] [1504] [1795]
103
137
203
170
401
400
397
398
Flow LPM [GPM]
Intermittent
22,7
[8]
[1150]
130
38
[1145]
129
79
[1137]
128
120
[1117]
126
160
[1095]
124
201
[1063]
120
241
[1035]
117
281
[1014]
115
301
Max.
Intermittent
[2150]
148
[1456]
165
30
[1447]
163
63
[1434]
162
96
[1406]
159
129
[1381]
156
162
[1345]
152
194
[1299]
147
226
[1279]
145
242
[1827]
206
30
[1827]
206
62
[1811]
205
95
[1777]
201
128
[1751]
198
160
[1722]
195
193
[1686]
190
226
[1661]
188
242
[2192]
248
28
[2201]
249
62
[2186]
247
94
[2160]
244
127
[2131]
241
158
[2088]
236
192
[2058]
233
224
[2030]
229
240
[2572]
291
26
[2577]
291
60
[2555]
289
92
[2531]
286
124
[2510]
284
156
[2480]
280
189
[2428]
274
222
[2404]
272
238
[2657]
300
25
[2669]
302
60
[2650]
299
91
[2625]
297
124
[2602]
294
156
[2571]
290
189
[2519]
285
221
[2493]
282
238
Max.
Intermittent
[2000]
138
[3671]
415
50
[3668]
414
80
[3644]
412
112
[3608]
408
145
[3571]
403
178
[3532]
399
212
[3488]
394
229
[785] [1152] [1520] [1877] [2222] [2318]
262
89
130
172
251
212
318
323
322
322
319
320
}
Torque [lb-in ]
Nm
Speed RPM
B-2-7
H Series (101-)
Performance Data
293 cm3/r [17.9 in3/r]
Max.
ContinContinuous
uous
[600] [800] [1000] [1200] [1350]
93
41
55
69
83
[200]
14
[400]
28
53,0
Max. [15]
Continuous 56,8
[427]
48
26
[419]
47
51
[402]
45
77
[367]
41
102
[332]
38
128
[289]
33
153
[241]
27
179
[211]
24
192
[893]
101
25
[886]
100
51
[872]
99
77
[838]
95
102
[803]
91
128
[760]
86
153
[712]
80
179
[683]
77
192
Max. [20]
Intermittent 75,7
[43]
5
256
area.
[2]
7,6
[4]
15,1
[6]
Flow LPM [GPM]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Continuous
Intermittent
[1361]
154
25
[1362]
154
51
[1342]
152
76
[1316]
149
102
[1276]
144
128
[1230]
139
153
[1176]
133
179
[1149]
130
192
53,0
Max. [15]
Continuous 56,8
[537]
61
20
[532]
60
40
[508]
57
61
[463]
52
81
[414]
47
101
[363]
41
121
[303]
34
142
[266]
30
152
Max. [20]
Intermittent 75,7
[61]
7
202
7,6
[4]
Flow LPM [GPM]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
[862]
97
152
B-2-8
}
Max.
ContinContinuous
uous
[400] [600] [800] [1000] [1200] [1250]
28
41
55
69
83
86
[1121]
127
20
[1123]
127
40
[1100]
124
61
[1060]
120
81
[1017]
115
101
[960]
108
121
[897]
101
142
[862]
97
152
[1715]
194
20
[1715]
194
40
[1693]
191
61
[1661]
188
81
[1613]
182
101
[1553]
175
121
[1484]
168
142
[1452]
164
152
[2285]
258
19
[2308]
261
39
[2294]
259
60
[2255]
255
80
[2203]
249
101
[2152]
243
121
[2086]
236
142
[2050]
232
152
[2862]
323
16
[2893]
327
38
[2884]
326
58
[2840]
321
79
[2788]
315
99
[2737]
309
119
[2667]
301
140
[2630]
297
150
[2672]
302
16
[2771]
313
47
[2757]
312
71
[2723]
308
98
[2684]
303
123
[2634]
298
149
[2592]
293
175
[2558]
289
188
Max.
Intermittent
[1500]
103
[2977]
336
13
[3110]
351
44
[3098]
350
68
[3070]
347
95
[3034]
343
120
[2989]
338
146
[2935]
332
172
[2905]
328
185
[4107]
464
22
[4121]
466
54
[4086]
462
84
[4061]
459
108
[4012]
453
135
[3963]
448
161
[3914]
442
174
739 cm3/r [45.1 in3/r]
[3604]
407
35
[3598]
407
53
[3557]
402
74
[3506]
396
94
[3446]
389
115
[3386]
383
136
[3347]
378
147
7,6
[4]
[4274]
483
15,1
27
[6]
[4283]
484
22,7
47
[8]
[4254]
481
30,3
68
[10]
[4212]
476
37,9
88
[12]
[4152]
469
45,4
109
[14]
[4092]
462
53,0
130
[4054]
Max. [15]
458 Contin140
uous 56,8
[671] [1269] [1847] [2410] [2987] [3119]
76
143
209
272
352
337
202
202
202
202
198
199
Max. [20]
Intermittent 75,7
Torque [lb-in]
Nm
Speed RPM
Max.
Intermittent
[800]
55
[3440]
389
10
[3440]
389
19
[3390]
383
29
[3330]
376
39
[3250]
367
48
[3130]
354
58
[3005]
340
68
[2905]
328
73
[4570]
516
9
[4600]
520
18
[4590]
519
27
[4515]
510
37
[4430]
501
46
[4320]
488
55
[4195]
474
66
[4130]
467
72
[ 143] [1350] [2565]
16
290
153
99
97
98
[3705]
419
96
Continuous
[200] [400]
14
28
[2]
[3467]
392
36
[3458]
391
55
[3414]
386
76
[3363]
380
96
[3305]
373
116
[3246]
367
137
[3206]
362
148
Max.
Continuous
[600]
41
Flow LPM [GPM]
[2]
[2293]
259
22
[2305]
260
49
[2291]
259
74
[2252]
254
100
[2215]
250
126
[2177]
246
151
[2126]
240
177
[2096]
237
190
[527] [1001] [1463] [1919] [2375] [2720]
268
60
113
165
217
307
252
256
255
255
254
249
370 cm3/r [22.6 in3/r]
[200]
14
[1829]
207
24
[1833]
207
50
[1819]
206
76
[1785]
202
101
[1749]
198
127
[1706]
193
153
[1650]
186
179
[1623]
183
191
Max.
Intermittent
[1800]
124
[1080]
122
10
[1070]
121
20
[1020]
115
30
[ 945]
107
40
[ 840]
95
50
[ 740]
84
60
[ 630]
71
69
[ 540]
61
74
[2250]
254
10
[2250]
254
20
[2200]
249
30
[2135]
241
40
[2050]
232
50
[1945]
220
59
[1820]
206
68
[1735]
196
74
H Series (101-)
Standard Rotation Viewed
from Shaft End
Dimensions
Port B Pressurized — CCW (Refer to pages B-4-19 thru
B-4-22 for shaft and port
dimensions.)
Note:
Mounting surface flatness
requirement is
,13 mm
[.005 inch] Max.
Note:
End ported motor pressure
is derated. Reference page
B-2-2 for ratings.
B-2
2 Bolt Flange
82,55/82,42
[3.250/3.245]
Pilot Dia.
End Port Motor Dim. YY Max.
Side Ports Plugged on End Ported Motor
Gerotor Width
X
End Ported Motor
End Cap
B Port
133,9
[5.27]
Max.
106,35
[4.187]
B Port
15,2 [.60]
13,62/13,46
[.550/.530] Dia. Thru
(2) Mounting Holes
2,8 [.11]
A Port
Side Port Motor Dim. Y Max.
98,3 [3.87] Max.
Standard Motor
End Cap
End Cap with Case Drain Port
also available.
Groove Provided for 82,6 [3.25] I.D. x
2,62 [.103] Cross Section O-ring ( Dash No. 152)
4 Bolt Flange
42,9
[1.69]
(2)
85,8
[3.38]
Max.
(2)
Mounting
Surface
84,0 2 and 4 Bolt Flange
[3.31] Displacement
XYYY
Max. cm3/r [in3/r]
mm [inch]
mm [inch]
mm [inch]
36 [ 2.2]
6,4 [ .25]
132,1 [5.20]
138,5 [5.45]
46 [ 2.8]
6,4 [ .25]
132,1 [5.20] 138,5 [5.45]
59 [ 3.6] 10,2 [ .40]
135,9 [5.35] 142,3 [5.60]
74 [ 4.5] 10,2 [ .40]
135,9 [5.35] 142,3 [5.60]
97 [ 5.9] 13,2 [ .52] 139,0 [5.47] 145,3 [5.72]
120 [ 7.3] 16,5 [ .65] 142,3 [5.60] 148,6 [5.85]
45
146 [ 8.9] 20,1 [ .79] 145,8 [5.74] 152,2 [5.99]
159 [ 9.7] 21,9 [ .86] 147,6 [5.81] 154,0 [6.06]
185
[11.3]
25,4
[1.00]
151,2
[5.95]
157,5
[6.20]
3/8-16 UNC (15,2 [.60] Max. Bolt Thread Engagement ) Mounting
231
[14.1]
31,8
[1.25]
157,5
[6.20]
Holes (4) Equally Spaced on 82,6 [3.25] Dia. Bolt Circle
293 [17.9] 40,4 [1.59] 166,2 [6.54] or
M10 x 1,5 (15,2 [.60] Max. Bolt Thread Engagement ) Mounting
370 [22.6] 50,8 [2.00] 176,6 [6.95] Holes (4) Equally Spaced on 82,6 [3.25] Dia. Bolt Circle
739 [45.1] 101,6 [4.00]
227,4 [8.95] 44,45/44,32
[1.750/1.745]
Pilot Dia.
B-2-9
H Series (101-)
Use digit prefix —101- plus
four digit number from
charts for complete product
number—Example 101-1001.
Product Numbers
2 Bolt Flange
Port
Shaft Size Displ. cm3/ r [in3/ r] / Product Number
36 46 59 74
97 120
146 159
185 231 293
370
740
[ 2.2] [ 2.8]
[ 3.6] [ 4.5] [ 5.9]
[ 7.3]
[ 8.9]
[ 9.7]
[11.3]
[14.1]
[17.9]
[22.6] [45.0]
101-1700 -1033-1701-1034-1035-1702-1703-1036-1037-1038-1039-1040—
1 in. Straight 7/8-14 O-Ring
1/2 NPTF101-1704 -1025-1705-1026-1027-1706-1707-1028-1029-1030-1031-1032—
w/Woodruff
key
Manifold*101-1708 -1041-1709-1042-1043-1710-1711-1044-1045-1046-1047-1048—
7/8-14 O-Ring
101-1721 -1081-1722-1082-1083-1723-1724-1084-1085-1086-1087-1088—
1 in. SAE 6B
1/2 NPTF101-1725 -1073-1726-1074-1075-1727-1728-1076-1077-1078-1079-1080—
Splined
Manifold*101-1729 -1089-1730-1090-1091-1731-1732-1092-1093-1094-1095-1096—
101-1796 -1797-1798-1799-1800-1801-1802-1803— — — — —
w/ .31 Dia.
1/2 NPTF101-1804 -1805-1806-1807-1808-1870-1809-1810— — — — —
Crosshole
Manifold*101-1811 -1812-1813-1814-1815-1816-1817-1818— — — — —
101-1819 -1323-1820-1324-1325-1821-1822-1326— — — — —
w/ .40 Dia.
1/2 NPTF101-1823 -1319-1824-1320-1825-1826-1827-1828— — — — —
Crosshole
Manifold*101-1829 -1463-1830-1831-1832-1833-1834-1871— — — — —
101-1834
4 Bolt Flange
Port
36 46 59 74
97 120
146 159
185 231 293
370
740
[ 2.2] [ 2.8]
[ 3.6] [ 4.5] [ 5.9]
[ 7.3]
[ 8.9]
[ 9.7]
[11.3]
[14.1]
[17.9]
[22.6] [45.0]
7
101-1749 -1009-1750-1010-1011-1751-1752-1012-1013-1014-1015-1016—
1 in. Straight w/ /8-14 O-Ring
-1001-1754-1002-1003-1755-1756-1004-1005-1006-1007-1008—
Woodruff
key 1/2 NPTF 101-1753 O-Ring
Manifold*101-1757 -1017-1758-1018-1019-1759 -1760-1020-1021-1022-1023-1024—
7/8-14 O-Ring
101-1761 -1057-1762-1058-1059-1872-1763-1060-1061-1062-1063-1064—
1 in. SAE 6B
1/2 NPTF 101-1764 -1049-1765-1050-1051-1766-1767-1052-1053-1054-1055-1056—
Splined
Manifold*101-1768 -1065-1769-1066-1067-1770-1771-1068-1069-1070-1071-1072—
101-1835 -1836-1837-1838-1839-1840-1841-1842— — — — —
w/
1/2 NPTF 101-1843 .31 Dia.
-1497-1844-1449-1352-1845-1846-1847— — — — —
Crosshole
Manifold*101-1848 -1466-1849-1459-1850-1851-1852-1853— — — — —
101-1854 -1311-1855-1856-1857-1858-1859-1860— — — — —
w/
1/2 NPTF 101-1861 .40 Dia.
-1313-1862-1312-1314-1863-1864-1315— — — — —
Crosshole
Manifold* 101-1865 -1305 -1866
-1306
-1307 -1867 -1868 -1869 — —
—
—
—
4 Bolt Flange with Corrosion Protection
Port
Shaft Size 101-1868
36 46 59 74
97 120
146 159
185 231 [ 2.2] [ 2.8]
[ 3.6] [ 4.5] [ 5.9]
[ 7.3]
[ 8.9]
[ 9.7]
[11.3]
[14.1]
101-2032 -2014
-2093
-2027
-2013
-2094 -2095 -2015 -2028
-2029
1 in. Straight 1/2 NPTF
w/
Woodruff Manifold*
-2067-2068
-2069
Key
*Manifold product numbers shown are for
motors with four 5/16-18 port face mounting
threads. Manifold, manifold mounting
O-Rings and bolts are NOT included.
B-2-10
For H Series Motors with a
configuration Not Shown in
the charts above: Use the
model code system on page
B-2-11 to specify the product
in detail. EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011
293
[17.9]
-2030 370
[22.6]
-2031 740
[45.0]
—
H Series (101-)
The following 25-digit coding system has been developed to
identify all of the configuration options for the H motor. Use
this model code to specify a motor with the desired features.
All 25-digits of the code must be present when ordering. You
may want to photocopy the matrix below to ensure that each
number is entered in the correct box.
Model Code
M
H 0
* * *
* *
* *
* *
*
*
*
* *
*
0
* *
*
*
0
J
1
2 3
4 5 6
7 8
9 10
11 12
13
14
15
16 17
18
19
20 21
22
23
24
25
1 Product
M - Motor
2 , 3 Series
H0 - H Motor
4 , 5 , 6 Displacement
cm3/r [in3/r]
022 – 36 [2.2]†
028 – 46 [2.8]
035 – 58 [3.5]†
045 – 74 [4.5]
059 – 96 [5.9]
FA – 4 Bolt (Standard)
44.40 [1.748] Dia. x 3.05
[.120] Pilot, M10 x 1.5-6H
Mounting Holes on 82.55
[3.250] Dia. B.C.
GA – 4 Bolt (Round) 82.50
[3.248] Dia. x 6.35 [.250]
Pilot, 19.05 [.750] Dia.
[4.310] Dia. B.C.
MA - 2 Bolt (Standard)
82.50 [3.248] Dia. x 8.13
[.320] Pilot, 13.59 [.535] Dia.
[4.187] Dia. B.C., w/o O-ring
Groove
073 – 120 [7.3]
089 – 146 [8.9]
097 – 159 [9.7]
113 – 185 [11.3]
141 – 231 [14.1]
179 – 294 [17.9]
226 – 370 [22.6]
451 – 739 [45.1]
†The H Series motors with
displacement code “022”
or “035” must also specify
free running gerotor (option
“AA” in position 11,12).
7 , 8 Mounting Type
AA – 2 Bolt (Standard)
82.50 [3.248] Dia. x 3.05
[.120] Pilot, 13.59 [.535]
Dia. Mounting Holes on
106.35 [4.187] Dia. B.C.
BA – 4 Bolt (Standard)
44.40 [1.748] Dia. x 3.05
[.120] Pilot, .375-16
UNC-2B Mounting Holes
on 82.55 [3.250] Dia. B.C.
CA – 2 Bolt (Standard)
82.50 [3.248] Dia. x 6.10
[.240] Pilot, 10.41 [.410] Dia.
[4.187] Dia. B.C. (SAE A)
DD – 2 Bolt (Standard)
101.60 [4.000] Dia. x 6.10
[.240] Pilot, 14.35 [.565] Dia.
[5.750] Dia. B.C. (SAE B)
9 , 10 Output Shaft
01 – 25.4 [1.00] Dia.
Straight, Woodruff Key,
.250-20 UNC-2B Hole in
Shaft End
02 – 25.4 [1.00] Dia. SAE 6B
Spline, .250-20 UNC-2B
Hole in Shaft End
07 – 25.4 [1.00] Dia. Straight,
8.03 [.316] Dia. Cross Hole
11.2 [.44] from End, 5.6 [.22]
Extra Length
08 – 25.4 [1.00] Dia.
Straight, 10.31 [.406] Dia.
Cross Hole 15.7 [.62] from
End, .250-20 UNC-2B Hole
in Shaft End
16 – 22.22 [.875] Dia. SAE
13 Tooth Spline (SAE B)
17 – 22.22 [.875] Dia.
Straight, 6.4 [.25] x 19.0 [.75]
Square Key (SAE B)
18 – 25.4 [1.00] Dia. Tapered,
Woodruff Key and Nut, 34.92
[1.375] Taper Length
24 – 25.00 [.984] Dia.
Straight, 8.00 [.315] KEY,
M8 x 1.25-6H Hole in
Shaft End
39 - 25.00 [.984] Dia.
Straight (k6), 8.00 [.315] Key,
M8 x 1.25-6H Hole in Shaft
End
11 , 12 Ports
AA – .875-14 UNF-2B SAE
O-Ring Ports
AB – .500-14 NPTF Dry
Seal Pipe Thread Ports
AC – Manifold Ports
(.3125-18 UNC-2B
Mounting Holes)
AD – Manifold Ports (M8 x
1.25-6H Mounting Holes)
AF – G 1/2 BSP Straight
Thread Ports
EB†† – End Ports: .750-16
UNF-2B SAE O-Ring Ports
EC†† – End Ports: G 1/2
BSP Straight Thread Ports
†† Note: End ported
motor pressure is derated.
Reference page B-2-2 for
ratings.
0 – None
1 – .4375-20 UNF-2B SAE
O-Ring Port (End Cap)
2 – G 1/4 BSP Straight
THD Port (End Cap)
A – Internal Check Valves
14 Gerotor Options
0 – None
A – Free Running
15 Shaft Options
0 – None
N – Electroless Nickel Plated
16 , 17 Seal Options
00 – Standard Seals
02 – Seal Guard
03 – Viton Seals
04 – Viton Shaft Seal
05 – Vented Two-Stage Seal
07 – High Pressure
Shaft Seal
B-2
(15 Pulse), No Lead Wire
with M12 Connector
(A=Power, B=Common,
C=Signal)
B – Magnetic Speed Pickup
(60 Pulse by Quadrature),
No Lead Wire with M12
Connector (A=Power,
B=Common, C=Signal)
Block
19 Manifold
Options
0 – None
ontact your Eaton
*–C
Sales Representative
for available options.
(Hardware)
00 – None
AB – Low Speed Valving
SS – S
tainless Steel
Flange Bolts
Features
22 Special
(Assembly)
0 – None
2 – Flange Rotated 90°
23 Paint/ Special
Packaging
0 – No Paint
A – Low Gloss Black Primer
D – Environmental Coated
Gloss White
F – Environmental
Coated Black
Assigned
24 Eaton
0 – Assigned Code
25 Eaton Assigned
Design Code
J – Nine (9)
18 Speed Sensor Options
0 – None
A – Digital Speed Pickup
Feature in bold are preferred and
allow for shorter lead time.
B-2-11
Notes
B-2-12
S Series (103-)
Features:
Geroler‚ design
Highlights
• Three moving components
(gerotor, drive, shaft)
New, improved design!
• Optimized drive running
angle
• Three-zone pressure
design (inlet, return
and case)
shafts and mounts
customer needs!
Benefits:
• High efficiency
• Smooth low speed
operation!
• Extended motor life
Description
The new improved Char-Lynn S Series motors with
optimized Geroler geometry offers enhanced performance
with reduced drive-running angle while retaining the overall
package size of the original S series. Design improvements
include upgraded steel end cap, O-Ring section seals, and
optimized Geroler set. The Geroler set has precisionmachined rollers in the outer ring which provide support
with rolling contact between the star and ring. This
improves mechanical efficiency, especially at start-up and at
low speed conditions. Improvements incorporated into the
latest S Series motor provide reliable leak-free performance
and smooth operation at start-up conditions.
Flow l/min [GPM]
10 Displacements
Speed
Pressure bar [PSI]
Torque Nm [lb-in]
performance
Applications:
harvesters, seeders
• Food processing
equipment
• Machine tools
Specifications
Geroler Element
• Ability to optimize designs
for your application needs
Up to 963 RPM
135 [2000] Cont.***
170 [2500] Inter.**
528 [4672] Cont.***
587 [5190] Inter.**
• Conveyors
floor polishers
• Saw mill works
• Turf equipment
equipment
• Many more
Conveyor
Casting
Amusement ride
Combine
B-3-1
B-3
S Series (103-)
Specifications
Thrust
Needle Bearing
Housing
Drive
Spacer Plate
Geroler
Output
Shaft
Exclusion
Seal
Pressure Seal
Flange
Cap Screws
Static Seals
End Cap
View of Geroler Section
Specification Data — S Motors
Displ. cm 3 /r [in 3 /r] 59 75 97 120144166187225 298372
[ 3.6]
[ 4.6]
[ 5.7]
[ 7.3]
[ 8.8]
[ 10.1] [11.4] [13.7] [18.2] [22.7]
Max. Speed (RPM) @ Continuous Flow
963
792
607
472
394
343
304
253
190
153 Flow LPM [GPM]
Continuous
57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15]
Intermittent
68 [18] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20]
Torque Nm [lb-in]
Continuous 115150183237265301333 372491528
[1021][1325][1623][2010][2347][2662][2950][3290][4345][4672]
Intermittent 144 186225292324 360 399 434505587
[1271][1649][1992][2582][2870][3191][3533][3843][4467][5200]
Min. Starting
@ Cont. Pressure
90 113148184212 232263302338369
Torque Nm[lb-in]
[ 800] [1000][1310][1630][2050][2330][2670][2990][3270][3270]
@ Int. Pressure
116146190236271289 329374417438
[1030][1290][1680][2090][2400][2560][2910][3310][3690] [3880]
Pressure Δ Bar
Continuous
138
138
138 138 131
131 128 117
103 90
[2000][2000][2000][2000][1900][1900][1850][1700][1500][1300]
[Δ PSI]
Intermittent
172
172 172 172 162 159 155 141 124 103
[2500] [2500] [2500] [2500] [2350] [2300] [2250] [2050] [1800] [1500]
A simultaneous
maximum torque and
maximum speed NOT
recommended.
Maximum Inlet Pressure:
Δ Pressure:
Recommended Fluids:
between inlet port and
outlet port
Note:
regard to ∆ Bar [∆ PSI] and/
6B Splined or Tapered
whenever operating above
282 NM [2500 lb-in] of
frequent reversals.
temperature.
load applications.
Continuous Rating:
Motor may be run
10% of every minute
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
4406, level 20/18/13
B-3-2
S Series (103-)
Performance Data
area.
Continuous
Flow LPM [GPM]
to unit in production
S Motor 59 cm3/r [3.6 in3/r]
Intermittent
[200][400][600][800][1000][1200][1400][1600][1800][2000][2500]
14284155 6983 97110124138172
[2] 86190292 390 484 578 662 729 764 803
102233 44 55 65 75 82 86 91
7,6 126121115 107 97 85 75 63 45 24
[4] 79185289 395 498 600 702 804 903 9981156
92133 45 56 68 79 91102 113131
15,1256250243 235 224 212 199 183 166 147 89
[6] 71177280 387 495 602 704 808 90910111257
82032 44 56 68 80 91103 114142
22,7
383
377
369360349336320302284266207
[8] 62166274 379 488 594 699 806 90710071264
7193143 5567 79 91102114143
30,3
514
508
500490477464448430409390333
[10] 52155264 369 475 583 686 793 89710001257
6173042 5466 78 90101113142
37,9
642
635
628617605591575557538517461
[12] 38141248 354 462 568 674 777 884 9871244
4162840 5264 76 88100 111141
45,4
772
764
757747736722706687670648592
[14] 21125231 337 445 551 658 763 868 9721233
2142638 5062 74 86 98110139
53,0
900
893
885876866852836819798778721
[15] 8116223 328 434 543 648 756 862 9651225
1132537 4961 73 85 97109138
56,8
482
958
949940929915900882863842784
[18] 86191296 403511 617 726 831 9351195
10 22
33
46
58
70
82
94 106 135
68,1
115111391128 11171105 1090 1074 1054 1033 977
B-3
Flow LPM [GPM]
[200][400][600][800][1000][1200][1400][1600][1800][2000][2500]
14284155 6983 97110124138172
[2] 91218343 467 590 708 815 900 9811086
102539 53 67 80 92102 111123
7,6 938981 75 66 59 43 21 23 16
[4] 87217352484 616748 8741001112312361472
102540 55 70 85 99113127140166
15,1193188181 173 163 150 139 125 107 89 37
[6] 82219355492 627763 8981027115512841590
92540 56 71 86101116131145180
22,7
292
286
277269258244228214202186140
[8] 69202341481 619761 8961032116512961618
82338 54 70 86101117132146183
30,3
390
384
375364355342326309295276230
[10] 56193330471 610751 8871025116212971628
62237 53 69 85100116131147184
37,9
489
484
476467457444431416399381336
[12] 39175315453 595736 8731011114812841617
42036 51 67 83 99114130145183
45,4
587
582
573564552540526510494476427
[14] 12153290431 571716 856 993112912651605
11733 49 65 81 97112128143181
53,0
343
680
673665654641628613594578533
[15] 9143281424 567708 846 985112112591599
11632 48 64 80 96 111127142181
56,8
491
729
723714704690675661644628580
[20] 82220362 505645 784 922106112001545
925 41 57 73 89104120136175
75,7 970
963957948935921906888871825
[143]
Torque [lb-in]
16Nm
729
Speed RPM
}
B-3-3
S Series (103-)
Performance Data
area.
Continuous
Flow LPM [GPM]
Intermittent
[200][400][600][800][1000][1200][1400][1600][1800][2000][2500]
14284155 6983 97110124138172
[2] 146308466 620 771 9131031108611761281
163553 70 87103116123133145
7,6 767264 55 48 34 22 7 4 1
[4] 136301466633 79795911161275143015701798
153453 72 90108126144162177203
15,1
158
153
146
138
126
115
10390775917
[6] 113278446616 78695211161280144416031971
133150 70 89108126145163181223
22,7238232225 215 206 191 175 161 145 129 87
[8] 98262431604 77794711121279144616102006
113049 68 88107126144163182227
30,3
319
313
306296284270255240224208165
[10] 81246415590 76393511001271143916042012
92847 67 86106124144163181227
37,9
400
394
388378366353340324306288244
[12] 65232401574 74691610811255142515912001
72645 65 84103122142161180226
45,4
481
476
469460448435423408394374326
[14] 42207376552 72189310641235140515701983
52343 62 81101120140159177224
53,0
561
557
549541531519504489470455412
[15] 31196364538 70888110521223139115601974
42241 61 80100119138157176223
56,8
602
597
591582571559546530514498453
[20] 119290461 633807 9761145131514851904
13 33
52
72
91 110 129 149 168 215
75,7 799
792785775762748734717702660
Flow LPM [GPM]
[200][400][600][800][1000][1200][1400][1600][1800][2000][2500]
14284155 6983 97110124138172
[2] 191403605 801 97811461288144015521679
224668 91110129146163175190
7,6 605650 43 36 29 19 15 8 6
[4] 1884036178291031123614381632181619901914
214670 94117140162184205225216
15,1
122
118
112
10698877867564916
[6] 1723916078211030124114491654185820562522
194469 93116140164187210232285
22,7186180175 167 159 149 137 126 114 103 73
[8] 1563755938071015122914391648185520592557
184267 91115139163186210233289
30,3
249
244
237229220210199185174162128
[10]130349567785 995121014201630183820452559
153964 89112137160184208231289
37,9
311
307
301293286275264252239227193
[12]103320539756 965117513831593179920032500
123661 85109133156180203226282
45,4
374
369
363355346336327314303288253
[14] 70285502715 923113113351540174519482452
83257 81104128151174197220277
53,0
437
433
427419411402391379369355322
[15] 54267485705 913112213291540174619472441
63055 80103127150174197220276
56,8
469
465
459452444433423411400386349
[20] 159377600 815102612321444165118592383
18 43
68
92 116 139 163 186 210 269
75,7 621
618612603594583571560549515
[267]
Torque [lb-in]
30Nm
465
Speed RPM
}
B-3-4
S Series (103-)
Performance Data
area.
Continuous
Flow LPM [GPM]
Intermittent
[200][400][600][800][1000][1200][1400][1600][1800][1900][2350]
14284155 6983 97110124138172
[2] 222 480 729 967119014021591 1786 2031 2107
25 54 82109134158180 202 229 238
7,6 494540 34 29 21 17 13 14 14
[4] 2174757289871237148817271957218122922310
245482112140168195221246259261
15,1
101
97
918477696152454222
[6] 1934537159761234149417461995223923582867
225181110139169197225253266324
22,7
153
149
143
136
128
119
110
101918666
[8] 1734346999611218147917351984223523582894
204979109138167196224252266327
30,3
205
202
195187179170160150139134109
[10]1444076739401197145917151967221823442890
164676106135165194222251265327
37,9
259
254
247240231221211202191185158
[12]1183806449071167142916851941219423192878
134373102132161190219248262325
45,4
312
307
301294286277267257246241217
[14] 873466108711131139516511907216322892851
103969 98128158187215244259322
53,0
363
359
354346339330319309299293266
[15] 693275928531113137616331890214622712835
83767 96126156185214242257320
56,8
389
386
380372364355344336323317289
[20] 200460726 987125115121770202521532724
2352 82112141171200229243308
75,7 516
513507499491480470459454427
B-3
Flow LPM [GPM]
[200][400][600][800][1000][1200][1400][1600][1800][1900][2300]
14284155 6983 97110124138172
[2] 267 563 8411105 13641622 1852 2081 2288
30 64 95 125 154 183 209 235 259
7,6 433935 30 27 21 16 13 13
[4] 24754483811291418170719882255251426413116
286195128160193225255284298352
15,1
89
85
807468605347413828
[6] 21751781311081401170019942281255926923214
255892125158192225258289304363
22,7
134
131
125
120
113
1059688797558
[8] 19549479410891387168719832269255226913239
225690123157191224256288304366
30,3180176171 164 156 147 138 128 118 114 96
[10]17647777610721371166819602249253726763228
205488121155188221254287302365
37,9
227
222
217210203194185175165160136
[12]13643673710371335163619282217250926513210
15 49 83117151185218 251 284 300 363
45,4
272
269
264258249241233223214208186
[14] 933946969951296159918902185247526173178
114479112146181214247280296359
53,0
318
315
310303296287279269259254230
[15] 733716729731272157518672159245325963158
84276110144178211244277293357
56,8
341
338
333326319309300290280274253
[20] 2275278291128143017242020231324573030
2660 94127162195228261278342
75,7 452
449443435426417407396390366
[371]
Torque [lb-in]
42Nm
338
Speed RPM
}
B-3-5
S Series (103-)
Performance Data
area.
Continuous
Flow LPM [GPM]
Intermittent
[200][400][600][800][1000][1200][1400][1600][1800][1850][2250]
14284155 6983 97110124138172
[2] 298 627 9441244 15321805 2030 2250 2478
34 71 107 141 173 204 229 254 280
7,6 373431 25 22 18 10 9 7
[4] 29864096912911607191922192511279928693411
3472109146182217251284316324385
15,1
78
75
706560534741353319
[6] 27962195312831608193022432551285029223502
3270108145182218253288322330396
22,7
119
115
110
10497898274666450
[8] 25259392812571579190522242542285529323539
2867105142178215251287323331400
30,3160156151 144 137 129 120 110 101 99 78
[10]21155588812171546187221932516283129093518
2463
100138175211248284320329397
37,9
201
198
193187180173164154143141114
[12]16250283511641490181821392463278028573476
185794131168205242278314323393
45,4
243
240
235229222214206196184181154
[14]11845278611171443177220952417273628143438
135189126163200237273309318388
53,0
283
280
276270262254245235224221194
[15] 9142575910891418174720682389270827863410
104886123160197234270306315385
56,8
304
301
296290283274265256243240214
[20] 2595909251255158519072229255226333265
2967105142179216252288297369
75,7 403
400394387379370359347344319
Flow LPM [GPM]
[200] [400] [600] [800][1000][1200][1400] [1600] [1700] [2050]
142841 55 69 83 97110124138
[2] 358 76511391498 18422163 2474 2738 2894
40 86129169208244280 309 327
7,6 322927 23 20 16 12 10 8
[4] 367 77411771577 19562325 2680 3022 3191 3753
41 87133178221263303 341 361 424
15,1666360 55 50 46 40 34 31 23
[6] 348 75811611567 19602344 2716 3083 3264 3863
39 86131177221265307 348 369 437
22,7999692 88 82 76 70 63 59 45
[8] 313 72111241529 19212312 2696 3073 3265 3894
3581
127173217261305347369440
30,3133132127 123 117 111 104 96 92 76
[10] 262 66910691473 18592247 2627 2997 3184 3810
3076
121166210254297339360430
37,9167165161 157 152 146 139 130 126 107
[12] 203 60910061400 17822160 2531 2912 3098 3721
2369114158201244286329350420
45,4202199196 191 186 180 173 165 160 141
[14] 143 544 9381324 17002079 2452 2824 3008 3639
16 62 106 150 192 235 277 319 340
411
53,0236233230 225 219 214 207 199 194 177
[15] 106 504 8971281 16532027 2393 2761 2944 3576
1257101145187229270312333404
56,8253251248 243 237 231 224 215 211 192
[20]
303 6971091 14771854 2214 2581 2765 3399
34 79 123 167 210 250 292 312 384
75,7 336334330 325318 312 304 298 282
[504]
Torque [lb-in]
57Nm
251
Speed RPM
}
B-3-6
S Series (103-)
Performance Data
area.
Continuous
Flow LPM [GPM]
Intermittent
[200] [400] [600] [800][1000][1200][1400] [1500] [1800]
142841 55 69 83 97110124
[2] 48710091509 1991 2460 2931 3360 3577 4113
55114170225 278331 380 404 465
7,6 242220 18 17 14 11 10 8
[4] 49810431576 2093 2597 3087 3567 3798 4500
56118178236 293349 403 429 508
15,1494745 41 38 34 31 29 25
[6] 47010171552 2080 2594 3097 3594 3835 4536
53115175235 293350 406 433 513
22,7747269 66 62 57 52 49 42
[8] 423 96715022031 25493062 3563 3807 4526
48109170229 288346 403 430 511
30,3
1009895 92 88 83 77 73 64
[10] 357 90114331961 24772989 3486 3730 4456
40102162222 280338 394 421 504
37,9126124121 118 113 108 101 97 87
[12] 287 82613571884 24022917 3410 3652 4363
32 93153213271330385 413 493
45,4152150147 144 140 134 126 121 109
[14] 199 73312611786 23032818 3316 3561 4276
22 83142202260318375 402 483
53,0177176173 170 165 160 152 147 134
[15] 154 68812181742 22582771 3273 3518 4241
17 78138197255313370 398 479
56,8190189186 183 178 173 165 160 146
[20]
418 9451471 19862502 3004 3253 3997
47107166224283339 368 452
75,7 253251248 244239 231 226 212
B-3
Flow LPM [GPM]
[200] [400] [600] [800][1000][1200][1400] [1500]
142841 55 69 83 97110
[2] 62912871905 2501 3066 3624 3886 4370
71145215283 346409 439 494
7,6 191816 14 13 11 9 7
[4] 62813041962 2600 3206 3799 4082 4642
71147222294 362429 461 525
15,1403836 34 30 27 25 23
[6] 58712611926 2578 3203 3813 4112 4687
66142218291 362431 465 530
22,7605956 54 50 45 43 38
[8] 52912011867 2518 3148 3769 4072 4657
60136211285 356426 460 526
30,3817977 75 71 66 64 58
[10] 45111241779 2429 3056 3678 3983 4583
51127201274345416450 518
37,9
102
1009896 9286 84 78
[12] 35910301688 2333 2963 3587 3889 4482
41116191264 335405 439 506
45,4122121119 117 113 107 104 98
[14] 256 92215772226 28643487 3787 4381
29104178252 324394 428 495
53,0143142140 137 134 128 126 119
[15] 199 86215142167 27973424 3727 4322
22 97171245 316387 421 488
56,8153152150 148 144 138 135 129
[20]
53411871832 24703093 3402 4004
60134207279349384 452
75,7 204202200 197192 189 183
[862]
Torque [lb-in]
97Nm
152
Speed RPM
}
B-3-7
S Series (103-)
Ports Dimensions
6-1/2 (BSP) Straight thread manifold (Refer to pages B-4-19 thru
dimensions.)
7/8-14 SAE O-Ring
Port B Pressurized — CCW 2 Bolt Flange
82,55/82,42
[3.250/3.245]
Pilot Dia.
Geroler Width
X
133,9
[5.27]
Max.
106,35
[4.187]
15,2 [.60]
13,62/13,46
[.550/.530] Dia. Thru
(2) Mounting Holes
98,3 [3.87] Max.
2,8 [.11]
Y Max.
B Port
Standard Motor
End Cap
A Port
Groove Provided for 82,6 [3.25]
I.D. x 2,62 [.103] Cross Section O-ring
( Dash No. 152)
4 Bolt Flange
42,9
[1.69]
(2)
Mounting
Surface
3.38 Max. (2)
85,8 [3.38]
44,45/44,32
[1.750/1.745]
Pilot Dia.
Displacement
cm3/r [in3/r]
58 [3.6]
76 [4.6]
93 [5.7]
120 [7.3]
144 [8.8]
107,7 165 [10.1]
[4.24]
Dia. 186 [11.4]
Max. 225 [13.7]
299 [18.2]
371 [22.7]
45°
3/8-16 UNC (15,2 [.60] Max. Bolt Thread Engagement)
Mounting Holes (4) Equally Spaced on 82,6 [3.25] Dia. Bolt Circle
or
B-3-8
X Y
mm [inch]
mm [inch]
7,5 [.30]
9,8 [.39]
12,0 [.47]
15,5 [.61]
18,6 [.73]
21,3 [.84]
24,0 [.94]
28,9 [1.14]
38,5 [1.52]
47,9 [1.88]
138,0 [5.43]
140,3 [5.52]
142,5 [5.61]
146,0 [5.75]
149,1 [5.87]
151,8 [5.98]
154,5 [6.08]
159,4 [6.28]
169,0 [6.66]
178,4 [7.02]
S Series (103-)
Use three-digit prefix (103-)
plus four-digit number from
number (ex: 103-1093).
without the three-digit
prefix.
Product Numbers
2 Bolt Flange
Port
59 [ 3.6] 103-1537
1 in. Straight 7/8-14 O-Ring 1/2 NPTF 103-1540
w/Woodruff
Key
Manifold 103-1543
7/8-14 O-Ring 103-1552
1 in. SAE 6B
1/2 NPTF 103-1555
Splined
Manifold 103-1558
B-3
75 93 120 144 166 187 225 298 372
[ 4.6]
[ 5.7] [ 7.3] [ 8.8] [ 10.1] [11.4] [13.7]
[18.2]
[22.7]
-1034-1035-1538-1539-1036-1037-1038 -1039-1040
-1026-1027-1541-1542-1028-1029-1030 -1031-1032
-1042-1043-1544-1545-1044-1045-1046 -1047-1048
-1082-1083-1553-1554-1084-1085-1086 -1087-1088
-1074-1075-1556-1557-1076-1077-1078 -1079-1080
-1090-1091-1559-1560-1092-1093-1094 -1095-1096
103-1093
4 Bolt Flange
Port
59 [ 3.6] 103-1570
1 in. Straight 7/8-14 O-Ring 1/2 NPTF w/Woodruff
103-1573
Key
Manifold 103-1576
7/8-14 O-Ring 1 in. SAE
103-1579
6BSplined
1/2 NPTF 103-1582
Manifold 103-1585
75 93 120 144 166 187 225 298 372
[ 4.6]
[ 5.7] [ 7.3] [ 8.8] [ 10.1] [11.4] [13.7]
[18.2]
[22.7]
-1010-1011-1571-1572-1012-1013-1014 -1015-1016
-1002-1003-1574-1575-1004-1005-1006 -1007-1008
-1018-1019-1577-1578-1020-1021-1022 -1023-1024
-1058-1059-1580-1581-1060-1061-1062 -1063-1064
-1050-1051-1583-1584-1052-1053-1054 -1055-1056
-1066-1067-1586-1587-1068-1069-1070 -1071 -1072 103-1069
S Series Motors with Corrosion Protection
Port
Shaft MountingSize Displ. cm3/ r [in3/ r] / Product Number
59 75 93 120 144 166 187 225 298 372
[ 3.6] [ 4.6]
[ 5.7] [ 7.3] [ 8.8] [ 10.1] [11.4] [13.7]
[18.2]
[22.7]
2
Bolt
7/8-14
O-Ring
103-1645
––––––-1649
–-1650
1 in. Straight
Flange
w/
Woodruff
Key
4 Bolt 1/2 NPTF– ––––––-1620 –-1621
Flange
*Manifold product numbers shown are
for motors with four 5/16 z-18 port face
mounting threads. Manifold, manifold
mounting O-Rings and bolts are NOT
included.
For S Series Motors with a
configuration Not Shown in
the charts above: Use the
model code number system
on page B-3-11 to specify
the product in detail. EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011
B-3-9
S Series
with Low Speed
Valving
Product Number
Motors with the low speed
valving option enable very
smooth low speed operation
while maintaining high
torque.
Designed to run
continuously at up to 200
RPM at standard rated
pressures and reduced
flows, this option provides
smooth operation at low
speeds. Furthermore, they
resist slippage and have
more momentary load
holding ability than the
standard H and S Series
motors. Motors with this
valving are not intended for
low pressure applications
(A minimum of 300 psi
delta must be maintained
between A port pressure
and case pressure). Shaft
side / radial load ratings are
not affected by this valving.
Use digit prefix—103plus four digit number
product number-—Example:
103-2678.
Orders will not be
accepted without the
three-digit prefix.
2 Bolt Flange
Port
59 [ 3.6] 7/8 -14 O-Ring 103- — 1 in. Straight
1/2 NPTF w/Woodruff
103- — Key
Manifold* 103- — 7/8 -14 O-Ring 103- — 1 in. SAE 6B
1/2 NPTF Splined
103- — Manifold* 103- — 75 [ 4.6]
-1427 -1419 —
-1525 —
-1522 93 [ 5.7] -1428 -1420 —
—
-1634 -2678 120 [ 7.3] —
—
—
—
—
—
144 [ 8.8] —
—
—
-2692 —
—
166 [ 10.1] -1429 -1421 —
—
—
—
187 [11.4] -1430 -1422 —
—
—
—
225 [13.7]
-1431 -1423 —
-1675 —
—
298 [18.2]
-1432 -1424 —
—
—
—
372
[22.7]
-1433 -1425 —
—
—
-1527 166 [ 10.1] -2531 -1404 187 [11.4] -1412 -1405 225 [13.7]
-1413 -1406 298 [18.2]
-1414 -1407 372
[22.7]
-1415 -1408
4 Bolt Flange
Port
59 [ 3.6] 7/8 -14 O-Ring 1 in. Straight
w/Woodruff
1/2 NPTF 103-1644 Key
75 93 [ 4.6]
[ 5.7] 103-1625 -1410 -1402 -1403 120 [ 7.3] -1411 —
144 [ 8.8] -1626 —
-1416 103-1404
103-1527
*Manifold product numbers shown are
for motors with four 5/16 -18 port face
mounting threads. Manifold, manifold
mounting O-Rings and bolts are NOT
included.
B-3-10
For S Series Motors with
Low Speed Valving Not
Shown in the chart above:
Use the model code number
system on page B-3-11 to
specify the product in detail.
S Series (103-)
to identify all of the configuration options for the S motor.
Model Code
1
2 3
4 5 6
1 Product
M – Motor
2 , 3 Series
S0 – S Series Motor
cm3/r [in3/r]
036 – 58 [3.6]
046 – 76 [4.6]
057 – 93 [5.7]
073 – 120 [7.3]
088 – 144 [8.8]
101 – 165 [10.1]
114 – 186 [11.4]
137 – 224 [13.7]
182 – 299 [18.2]
227 – 371 [22.7]
7 , 8 Mounting Type
AA – 2 Bolt Std: 82.50
[3.248] Dia. x 3.05 [.120]
Pilot, 13.59 [.535] Dia.
[4.187] Dia. B.C.
BA – 4 Bolt Std: 44.40
[1.748] Dia. x 3.05 [.120]
Pilot, .375-16 UNC-2B
[3.250] Dia. B.C.
CA – 2 Bolt Std: 82.50
[3.248] Dia. x 6.10 [.240]
Pilot, 10.41 [.410] Dia.
[4.187] Dia. B.C. (SAE A)
DD – 2 Bolt Std: 101.60
[4.000] Dia. x 6.10 [.240]
Pilot, 14.35 [.565] Dia.
[5.750] Dia. B.C. (SAE B)
(Ductile)
EA – 4 Bolt Magneto: 82.50
[3.248] Dia. x 3.05 [.120]
Pilot, 13.59 [.535] Dia.
[4.187] Dia. B.C.
FA – 4 Bolt Std: 44.40
[1.748] Dia. x 3.05 [.120]
7 8
10
11 12
13
14
Pilot, M10 x 1.5-6h
[3.250] Dia. B.C.
LA – 2 Bolt Std: 44.45
[1.750] Dia. x 3.05 [.120]
Pilot, 13.59 [.535] Dia.
[4.187] Dia. B.C.
82.50 [3.248] Dia. x 8.13
[.320] Pilot, 13.59 [.535] Dia.
[4.187] Dia. B.C., w/o O-ring
Groove
9 , 10 Output Shaft
01 – 25.4 [1.00] Dia.
Shaft End
02 – 25.4 [1.00] Dia. SAE
6B Spline, .250-20 UNC-2B
Hole in Shaft End
07 – 25.4 [1.00] Dia. Straight,
8.03 [.316] Dia. Crosshole
11.2 [.44] From End, 5.6 [.22]
Extra Length
15
16 17
18
19
11 , 12 Port Type
AA – .875-14 UNF-2B SAE
O-Ring Ports
AB – .500-14 NPTF Dryseal
Pipe Thread Ports
AC – Manifold Ports
(.3125-18 UNC-2B
Mounting Holes)
AD – Manifold Ports (M8 x
Thread Ports
13 Case Flow Options ††
0 – None Specified
1 – 4375-20 UNF-2B SAE
2 – G 1/4 BSP Straight
THD Port (End Cap)
3 – Manifold Case Drain
25
No lead wire with M12
connector
15 Shaft Options
02 – Seal Guard
03 – Viton Seals
07 – High Pressure Shaft
Seal
18 Speed Sensor Options
0 – None
A – Speed Sensor Options
12mm Digital Speed Pickup
(15 pulse) without lead wire
B-3
(A=Power, B=Common,
C=Signal)
Block
19 Manifold
Options
0 – None
* Contact your Eaton
sales representative for
available options.
20 , 21 Special Features (Hardware)
SS – Stainless Steel Flange
Bolts
22 Special Assembly
Instructions
2 – Flange Rotated 90°
39 - 25.00 [.984] Dia.
Straight (k6), 8.00 [.315]
Key, M8 x 1.25-6H Hole in
Shaft End
24
14 Geroler Options
16 – 22.22 [.875] Dia. SAE
24 – 25.00 [.984] Dia.
Straight, 8.00 [.315] Key,
M8 x 1.25-6H Hole in Shaft
End
23
0 – None
18 – 25.4 [1.00] Dia. Tapered,
Woodruff Key and Nut,
34.92 [1.375] Taper Length
22
†† – Internal check valves
are standard features.
08 – 25.4 [1.00] Dia.
Straight, 10.31 [.406] Dia.
Crosshole 15.7 [.62] From
in Shaft End
17 – 22.22 [.875] Dia.
Straight, 6.4 [.25] x 19.0
[.75] Square Key (SAE B)
20 21
3 – Reverse Rotation, Flange
Rotated 90°
23 Paint/Packaging
Options
0 – No Paint
A – Low Gloss Black
Primer
Gloss White
F – Environmental Coated
Black
24 Eaton Assigned Code
When Applicable
0 – Assigned Code
25 Eaton Assigned Design
Code
M – Twelve (12)
B-3-11
Notes
B-3-12
T Series (158-)
Features:
Geroler‚ geometry
Highlights
• Optimized drive system
with reduced running
angle
• Three-pressure zone
design (ability to reduce
case pressure)
Port B
Port A
shafts and mounts
customer needs
Benefits:
• High efficiency
Geroler Star
T Series
Motors
Motor Shaft Drive
• Smooth low-speed
operation
• Extended motor life (especially at low speed conditions)
Description
The newest Geroler motor, the “T Series, features the latest
innovations in Geroler technology. These innovations include
optimized Geroler geometry with lower drive running angle
for improved life and improved low speed performance.
In addition, the improved housing and smaller diameter
end cap results in increased envelope rigidity which
improves efficiency under high pressure loads. All of these
innovations come together to make the T Series motor the
highest performing motor in its class.
Specifications for T Series Motors
Geroler Element
Flow l/min [GPM]
11 Displacements
Speed
Up to 1021 RPM
Pressure bar [PSI]
155 [2250] Cont.***
190 [2750] Inter.**
Torque Nm [lb-in]
441 [3905] Cont.***
486 [4300] Inter.**
• Ability to optimize
designs for your
application needs
• Extends leak-free
performance
Applications:
harvesters, seeders
• Food processing
equipment
• Machine tools
• Conveyors
floor polishers
• Saw mill works
• Turf equipment
equipment
• Many more
Crane (winch)
Paving
Harvester
Crane and winches
B-4-1
B-4
T Series (158-)
Specifications
Port B
Port A
Geroler Star
T Series
Motors
Motor Shaft Drive
Specification Data — T Motors
Displ. cm 3 /r [in 3 /r] 36 49 66 80 102131157195244306370
[2.2][3.0][4.0][4.9][6.2][8.0][9.6][11.9][14.9][18.7][22.6]
Max. Speed (RPM) 1021906849694550426355287229183152
@ Continuous Flow
Flow LPM Continuous
38 [10] 45 [12] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15]
[GPM]
Intermittent 38 [10] 57 [15] 68 [18] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20]
TorqueContinuous
76 105138174219251297359410441430
Nm [lb-in]
[672] [928] [1222][1541][1936][2226][2628][3178][3633][3905][3811]
Intermittent **
93 118168212264307359437485483486
[824] [1131][1488][1872][2339][2718][3178][3864][4290][4275][4300]
Pressure
Continuous*
15515515515515513813813812711090
∆ Bar
[2250][2250][2250][2250][2250][2000][2000][2000][1850][1600][1300]
∆ PSI]Intermittent**
190190190190190172172172155124103
[2750][2750][2750][2750][2750][2500][2500][2500][2250][1800][1500]
A simultaneous
maximum torque and
maximum speed NOT
recommended.
Δ Pressure:
Recommended Fluids:
regard to ∆ Bar [D PSI] and/
outlet port
Note:
6B splined or Tapered
whenever operation above
282 NM [2500 lb-in] of
frequent reversals.
temperature.
load applications.
Continuous Rating:
Motor may be run
10% of every minute
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
4406, level 20/18/13
B-4-2
T Series
(158-, 185-)
36 cm3/r [2.2 in3/r]
Performance Data
vary slightly from unit to unit
in production.
[2]
Flow LPM [GPM]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2250]
155
97
124
55
69
83
110
138
152
[50]
6
209
[50]
6
415
[43]
5
617
[39]
4
821
[30]
3
1021
[110]
12
203
[109]
12
411
[108]
12
613
[101]
11
815
[93]
11
1014
[172]
19
197
[172]
19
398
[171]
19
602
[164]
19
803
[155]
18
1002
[233]
26
191
[233]
26
388
[233]
26
595
[226]
26
797
[214]
24
999
[596]
67
116
[659]
74
302
[672]
76
496
[670]
76
680
[668]
75
873
[635]
72
64
[786]
89
283
[824]
93
425
[819]
92
607
[805]
91
799
Max.
Intermittent
[2750]
190
Max.
Continuous
7,6
[4]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[291]
33
189
[296]
33
384
[298]
34
585
[292]
33
784
[278]
31
981
[348]
39
181
[355]
40
381
[361]
41
570
[354]
40
774
[342]
39
965
[401]
45
167
[414]
47
368
[420]
47
563
[415]
47
758
[406]
46
953
[455]
51
164
[475]
54
357
[479]
54
558
[475]
54
747
[473]
53
937
[501]
57
153
[534]
60
354
[538]
61
534
[538]
61
732
[532]
60
921
[546]
62
139
[584]
66
323
[595]
67
520
[592]
67
707
[590]
67
903
[590]
67
122
[646]
73
304
[657]
74
504
[656]
74
688
[650]
73
880
Max.
Intermittent
[2750]
190
Continuous
[93]
11
1014
Intermittent
}
Torque [lb-in ]
Nm
Speed RPM
49 cm3/r [3.0 in3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2250]
97
138
152
55
69
83
110
155
124
[73]
8
152
[72]
8
303
[58]
7
461
[44]
5
607
[39]
4
755
[33]
4
906
[161]
18
152
[160]
18
298
[148]
17
450
[127]
14
603
[128]
14
750
[119]
13
902
[245]
28
148
[246]
28
294
[234]
26
445
[216]
24
600
[213]
24
745
[203]
23
895
[327]
37
147
[329]
37
290
[326]
37
438
[306]
35
590
[302]
34
738
[291]
33
883
[408]
46
142
[416]
47
276
[413]
47
434
[392]
44
583
[391]
44
732
[378]
43
875
[486]
55
141
[500]
56
273
[500]
56
421
[480]
54
576
[477]
54
719
[464]
52
862
[563]
64
134
[584]
66
265
[583]
66
419
[566]
64
564
[562]
63
713
[551]
62
859
[641]
72
124
[668]
75
261
[663]
75
410
[652]
74
554
[647]
73
702
[635]
72
844
[710]
80
115
[746]
84
245
[746]
84
407
[734]
83
545
[731]
83
696
[719]
81
835
[786]
89
109
[825]
93
243
[827]
93
389
[815]
92
536
[815]
92
682
[802]
91
819
[849]
96
95
[901]
102
235
[909]
103
376
[897]
101
522
[897]
101
663
[883]
100
806
[866]
98
92
[922]
104
228
[928]
105
373
[917]
104
520
[917]
104
661
[900]
102
804
[26]
3
1132
[86]
10
1124
[172]
19
1113
[256]
29
1115
[342]
39
1106
[430]
49
1106
[505]
57
1098
[591]
67
1093
[674]
76
1079
[745]
84
1070
[830]
94
1058
[851]
96
1056
[2]
Flow LPM [GPM]
7,6
[4]
Max.
Continuous
Max.
Intermittent
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[15]
56,8
[1023]
116
58
[1123]
127
152
[1131]
128
344
[1125]
127
503
[1121]
127
638
[1061]
120
788
B-4-3
B-4
T Series
(158-, 185-)
Performance Data
66 cm3/r [4.0 in3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2250]
55
69
83
110
152
97
138
124
155
[78]
9
114
[97]
11
229
[79]
9
344
[75]
8
456
[49]
6
569
[24]
3
681
[19]
2
793
[13]
1
849
[191]
22
111
[209]
24
229
[192]
22
343
[191]
22
451
[163]
18
565
[156]
18
678
[143]
16
788
[120]
14
844
[303]
34
110
[325]
37
217
[309]
35
335
[304]
34
447
[283]
32
560
[270]
31
671
[261]
29
787
[236]
27
839
[414]
47
107
[441]
50
216
[426]
48
334
[419]
47
442
[398]
45
552
[385]
43
665
[370]
42
778
[352]
40
832
[522]
59
105
[548]
62
212
[534]
60
321
[532]
60
431
[509]
58
547
[502]
57
658
[485]
55
771
[471]
53
826
[625]
71
101
[657]
74
205
[649]
73
320
[645]
73
426
[623]
70
541
[614]
69
651
[602]
68
762
[590]
67
819
[706]
80
96
[766]
87
194
[760]
86
319
[759]
86
419
[742]
84
532
[729]
82
641
[718]
81
753
[707]
80
806
[804]
91
92
[873]
99
190
[874]
99
315
[871]
98
415
[856]
97
525
[845]
95
635
[837]
95
746
[823]
93
800
[898]
101
87
[972]
110
186
[984]
111
291
[982]
111
412
[971]
110
512
[963]
109
623
[948]
107
733
[939]
106
786
[107]
12
1006
[215]
24
1003
[326]
37
998
[442]
50
988
[555]
63
976
[669]
76
975
[786]
89
965
[900] [1016] [1123] [1152]
102
115
130
127
952
940
919
924
Continuous
15,1
[6]
Flow LPM [GPM]
in production.
[2]
7,6
[4]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Intermittent
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[18]
68,1
[991]
112
81
[1077]
122
183
[1090]
123
288
[1092]
123
401
[1080]
122
504
[1067]
121
612
[1064]
120
723
[1052]
119
779
[1081]
122
73
[1181]
133
181
[1190]
134
279
[1197]
135
391
[1186]
134
498
[1182]
134
604
[1175]
133
715
[1165]
132
770
[1103]
125
72
[1205]
136
178
[1218]
138
276
[1222]
138
386
[1209]
137
496
[1209]
137
601
[1199]
135
711
[1192]
135
766
80 cm3/r [4.9 in3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2250]
110
152
55
69
83
97
138
155
124
[123]
14
93
[120]
14
187
[113]
13
279
[99]
11
372
[84]
9
463
[63]
7
557
[55]
6
649
[51]
6
694
[265]
30
90
[264]
30
185
[255]
29
275
[243]
27
367
[228]
26
460
[209]
24
552
[185]
21
646
[176]
20
691
[405]
46
86
[406]
46
183
[398]
45
271
[386]
44
364
[371]
42
456
[354]
40
547
[331]
37
642
[316]
36
687
[544]
61
83
[551]
62
179
[542]
61
267
[528]
60
359
[514]
58
450
[498]
56
543
[476]
54
635
[463]
52
680
[680]
77
80
[689]
78
175
[682]
77
265
[669]
76
354
[655]
74
446
[638]
72
537
[620]
70
630
[609]
69
673
[804]
91
75
[828]
94
171
[823]
93
258
[812]
92
351
[798]
90
441
[782]
88
530
[762]
86
622
[748]
85
668
[934]
106
70
[965]
109
166
[963]
109
253
[954]
108
343
[941]
106
435
[926]
105
523
[904]
102
616
[891]
101
660
[160]
18
916
[305]
34
910
[455]
51
893
[578]
65
893
[737]
83
875
[857]
97
866
[2]
7,6
[4]
Flow LPM [GPM]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[20]
75,7
[176]
20
691
B-4-4
}
Torque [lb-in ]
Nm
Speed RPM
[1052]
119
63
[1101]
124
162
[1101]
124
248
[1094]
124
338
[1080]
122
428
[1067]
121
515
[1046]
118
609
[1037]
117
650
[1181]
133
57
[1237]
140
156
[1239]
140
240
[1233]
139
333
[1219]
138
420
[1208]
136
509
[1188]
134
599
[1177]
133
642
[1079]
122
43
[1369]
155
150
[1373]
155
232
[1368]
155
324
[1357]
153
412
[1346]
152
500
[1327]
150
592
[1316]
149
634
[937]
106
24
[1505]
170
142
[1508]
170
223
[1503]
170
315
[1496]
169
403
[1484]
168
489
[1467]
166
581
[1457]
165
622
[895]
101
20
[1537]
174
140
[1541]
174
221
[1537]
174
313
[1530]
173
399
[1520]
172
487
[1502]
170
578
[1491]
168
619
[968] [1144] [1277] [1412] [1446]
129
144
163
160
109
843
833
836
839
877
Max.
Intermittent
[2750]
190
[1318]
149
48
[1437]
162
170
[1488]
168
270
[1458]
165
339
[1425]
161
475
[1472]
166
571
[1436]
162
677
[1462]
165
725
Max.
Intermittent
[2750]
190
[1857]
210
121
[1868]
211
198
[1872]
212
289
[1870]
211
368
[1864]
211
470
[1842]
208
550
[1844]
208
598
T Series
(158-, 185-)
102 cm3/r [6.2 in3/r]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2250]
110
55
69
83
152
138
97
124
155
[161]
18
73
[157]
18
149
[147]
17
221
[132]
15
294
[109]
12
367
[84]
9
440
[59]
7
513
[39]
4
550
[341]
39
71
[340]
38
146
[329]
37
217
[315]
36
290
[293]
33
363
[271]
31
436
[242]
27
510
[227]
26
545
[519]
59
68
[520]
59
144
[510]
58
214
[497]
56
287
[477]
54
360
[457]
52
432
[428]
48
506
[411]
46
542
[697]
79
66
[702]
79
141
[692]
78
211
[675]
76
284
[657]
74
355
[638]
72
429
[611]
69
501
[595]
67
537
[871]
98
63
[879]
99
138
[871]
98
208
[857]
97
280
[839]
95
351
[818]
92
424
[794]
90
497
[780]
88
532
[154]
17
724
[328]
37
718
[515]
58
720
[710]
80
709
Performance Data
7,6
[4]
15,1
[6]
Flow LPM [GPM]
in production.
[2]
30,3
[10]
37,9
[12]
45,4
[14]
Continuous
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[20]
75,7
[1193]
135
56
[1229]
139
131
[1227]
139
199
[1216]
137
271
[1198]
135
343
[1179]
133
414
[1151]
130
487
[1136]
128
522
[1349]
152
51
[1401]
158
128
[1401]
158
195
[1392]
157
267
[1374]
155
337
[1354]
153
409
[1328]
150
482
[1314]
148
516
[1511]
171
46
[1567]
177
124
[1571]
178
190
[1564]
177
262
[1542]
174
332
[1527]
173
402
[1502]
170
475
[1486]
168
510
[1496]
169
36
[1727]
195
118
[1731]
196
184
[1725]
195
255
[1711]
193
325
[1697]
192
395
[1674]
189
469
[1658]
187
502
131 cm3/r [8.0 in3/r]
[2]
[200]
14
[400]
28
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800] [2000]
55
69
83
110
138
97
124
[219]
25
57
[212]
24
115
[197]
22
171
[181]
20
227
[144]
16
284
[114]
13
341
[82]
9
397
[66]
7
426
[450]
51
55
[449]
51
113
[435]
49
168
[417]
47
225
[389]
44
281
[361]
41
338
[327]
37
394
[302]
34
423
[682]
77
53
[681]
77
110
[669]
76
166
[657]
74
222
[631]
71
278
[605]
68
334
[569]
64
391
[550]
62
422
[915]
103
51
[917]
104
109
[903]
102
163
[886]
100
219
[859]
97
275
[838]
95
332
[803]
91
387
[785]
89
415
7,6
[4]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[20]
75,7
[177]
20
565
[429]
48
560
[678]
77
556
[302]
34
423
[1144]
129
49
[1148]
130
107
[1139]
129
160
[1122]
127
217
[1098]
124
271
[1075]
121
328
[1042]
118
384
[1025]
116
412
[1441]
163
23
[1889]
213
111
[1895]
214
176
[1891]
214
247
[1878]
212
318
[1858]
210
386
[1841]
208
458
[1828]
207
492
[1421]
161
20
[1925]
217
109
[1936]
219
174
[1932]
218
245
[1918]
217
315
[1901]
215
384
[1883]
213
456
[1869]
211
490
[2271]
257
92
[2339]
264
154
[2326]
263
220
[2326]
263
287
[2323]
262
364
[2301]
260
428
[2285]
258
463
[874] [1060] [1243] [1405] [1579] [1763] [1803]
120
159
178
204
99
140
199
696
683
670
660
707
684
659
Flow LPM [GPM]
Intermittent
22,7
[8]
[1030]
116
60
[1056]
119
135
[1050]
119
204
[1038]
117
277
[1018]
115
347
[999]
113
419
[974]
110
492
[957]
108
528
Max.
Intermittent
[2750]
190
[1348]
152
47
[1376]
155
105
[1370]
155
157
[1359]
154
213
[1330]
150
267
[1307]
148
325
[1273]
144
361
[1254]
142
409
[1561]
176
43
[1600]
181
102
[1600]
181
154
[1589]
180
209
[1562]
176
265
[1532]
173
321
[1498]
169
378
[1480]
167
405
[1771]
200
40
[1822]
206
99
[1818]
205
150
[1812]
205
206
[1783]
201
261
[1755]
198
318
[1722]
195
374
[1704]
193
402
[1979]
224
36
[2025]
229
96
[2032]
230
147
[2022]
228
202
[1993]
225
258
[1965]
222
312
[1935]
219
370
[1915]
216
398
[2159]
244
30
[2221]
251
91
[2226]
252
142
[2215]
250
196
[2198]
248
252
[2177]
246
307
[2147]
243
365
[2119]
239
392
Max.
Intermittent
[2500]
172
[2629]
297
75
[2718]
307
125
[2699]
305
175
[2687]
304
231
[2671]
302
285
[2655]
300
339
[2648]
299
367
[908] [1143] [1375] [1596] [1811] [2017]
129
103
155
205
228
180
549
553
546
536
527
541
}
Torque [lb-in ]
Nm
Speed RPM
B-4-5
B-4
T Series
(158-, 185-)
157 cm3/r [9.6 in3/r]
Performance Data
in production.
[2]
7,6
[4]
15,1
[6]
Flow LPM [GPM]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Continuous
Intermittent
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1800] [2000]
55
69
83
110
124
97
138
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
Max.
Intermittent
[2500]
172
[200]
14
[400]
28
[600]
41
[264]
30
47
[259]
29
96
[241]
27
142
[219]
25
189
[180]
20
237
[141]
16
284
[101]
11
332
[81]
9
355
[541]
61
45
[541]
61
95
[526]
59
140
[506]
57
187
[472]
53
234
436]
49
282
[397]
45
329
[367]
41
353
[819]
93
44
[822]
93
92
[808]
91
138
[789]
89
185
[759]
86
232
[728]
82
279
[687]
78
326
[665]
75
350
[221]
25
472
[519]
59
467
[814] [1095] [1368] [1631] [1891] [2149] [2396]
243
92
124
184
271
155
214
443
464
462
455
433
459
450
[600]
41
Max.
ContinContinuous
uous
[800] [1000] [1200] [1400] [1600] [1750] [1800] [2000]
97
55
69
83
110
125
138
121
[20]
75,7
[1092]
123
42
[1101]
124
91
[1090]
123
136
[1068]
121
183
[1037]
117
230
[1010]
114
277
[969]
109
323
[944]
107
347
[1357]
153
40
[1373]
155
90
[1368]
155
134
[1348]
152
181
[1319]
149
227
[1292]
146
274
[1252]
141
321
[1231]
139
344
[1605]
181
37
[1638]
185
88
[1638]
185
132
[1625]
184
178
[1590]
180
224
[1561]
176
272
[1519]
172
319
[1497]
169
342
[1847]
209
∆34
[1890]
214
85
[1900]
215
129
[1885]
213
175
[1853]
209
222
[1821]
206
269
[1778]
201
316
[1755]
198
339
[2084]
235
30
[2145]
242
82
[2150]
243
125
[2140]
242
172
[2111]
239
218
[2079]
235
265
[2040]
230
311
[2018]
228
334
[2311]
261
25
[2383]
269
78
[2399]
271
121
[2388]
270
166
[2355]
266
211
[2331]
263
257
[2295]
259
305
[2273]
257
327
[1858]
210
16
[2613]
295
73
[2628]
297
114
[2619]
296
159
[2594]
293
203
[2573]
291
248
[2539]
287
296
[2512]
284
318
[3063]
346
60
[3169]
358
99
[3178]
359
140
[3170]
358
183
[3162]
357
225
[3147]
356
274
[3136]
354
300
195 cm3/r [11.9 in3/r]
[2]
7,6
[4]
Flow LPM [GPM]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Max.
Continuous
Max.
Intermittent
53,0
[15]
56,8
[400]
28
[330]
37
38
[328]
37
77
[306]
35
115
[272]
31
153
[238]
27
192
[181]
20
230
[154]
17
268
[140]
16
287
[671] [1016]
76
115
36
34
[675] [1026]
76
116
77
75
[658] [1011]
74
114
113
111
[634] [980]
72
111
151
150
[596] [945]
67
107
189
188
[545] [908]
62
103
228
226
[500] [860]
56
97
266
264
[465] [832]
53
94
285
283
[291]
33
382
[20]
75,7
[465]
53
285
B-4-6
[200]
14
[1345]
152
33
[1366]
154
73
[1360]
154
110
[1331]
150
148
[1296]
146
186
[1260]
142
224
[1211]
137
261
[1179]
133
281
[1654]
187
31
[1692]
191
73
[1698]
192
109
[1675]
189
146
[1637]
185
184
[1607]
182
222
[1556]
176
259
[1525]
172
279
[1969]
222
28
[2010]
227
71
[2021]
228
107
[2003]
226
144
[1960]
221
183
[1924]
217
221
[1869]
211
259
[1835]
207
278
[2242]
253
25
[2289]
259
68
[2324]
263
104
[2300]
260
142
[2255]
255
181
[2223]
251
219
[2175]
246
256
[2144]
242
275
[2507]
283
20
[2586]
292
65
[2604]
294
100
[2592]
293
139
[2565]
290
176
[2529]
286
213
[2483]
281
251
[2459]
278
269
[2689]
304
16
[2799]
316
62
[2829]
320
97
[2815]
318
134
[2786]
315
168
[2759]
312
207
[2713]
307
244
[2693]
304
262
[2748]
310
14
[2867]
324
61
[2901]
328
95
[2888]
326
132
[2857]
323
166
[2836]
320
204
[2792]
315
242
[2768]
313
260
[2973]
336
8
[3144]
355
55
[3178]
359
87
[3174]
359
123
[3140]
355
156
[3121]
353
192
[3080]
348
229
[3061]
346
247
[653] [1013] [1366] [1689] [1987] [2298] [2540] [2622] [2928]
191
74
114
154
225
287
331
296
260
372
378
375
373
368
356
342
353
363
}
Torque [lb-in ]
Nm
Speed RPM
Max.
Intermittent
[2500]
172
[3797]
429
40
[3831]
433
68
[3864]
437
99
[3816]
431
133
[3807]
430
160
[3778]
427
199
[3764]
425
220
T Series
(158-, 185-)
Max.
Intermittent
Performance Data
[200]
14
Flow LPM [GPM]
[1655]
187
26
[1695]
192
59
[6]
[382] [823] [1261] [1687]
Performance data43 is typical
93
142
191
22,7
92
91
90
89
at 120 SUS.
Actual
data
may
[341] [787] [1220] [1651]
[8]
vary slightly
from
39 unit89to unit
138
187
123
122
121
120
30,3
in production.
[297] [744] [1177] [1611]
[10]
34
84
133
182
154
152
151
150
37,9
[225] [687] [1132] [1553]
[12]
25
78
128
175
184
183
181
180
45,4
Continuous
[154] [628] [1072] [1498]
[14]
17
71
121
169
214
213
212
211
53,0
[119]
[586]
[1035]
[1458]
[15]
Max. Intermittent
13
66
117
165
Contin229
228
227
226
56,8
uous
Max.
Intermittent
[372]
42
305
[20]
75,7
[2038]
230
24
[2083]
235
59
[2088]
236
88
[2059]
233
119
[2017]
228
148
[1967]
222
179
[1910]
216
209
[1872]
212
224
[2403] [2707]
272
306
22
17
[2468] [2820]
279
319
57
55
[2477] [2843]
280
321
86
82
[2454] [2820]
277
319
116
113
[2412] [2774]
273
313
146
143
Max.
[2360] [2734]
Contin-309
267
177 uous173
[2298] Max.
[2674]
260Inter-302
207
mittent202
[2261] [2637]
255
298
222
217
[816] [1251] [1663] [2067] [2448]
92
141
188
277
234
303
301
300
292
297
[2]
[499] [1035]
Max.
Max.
56
117
Inter7,6 Contin24
23
uous mittent
[4]
[497] [1052]
[1200] [1400] [1500] [1600]
56 [1800]
119
97 15,1
103
83
124
110
49
49
[6]
[480] [1031]
[2912] [3239] [2859]
[2400]
54
116
329
366
323
271
74
74
16
11 22,7 8
5
[427] [975]
[8]
[3023] [3464] [3680]
[3886]
[4221]
48
110
342
391
416
439
477
99
9830
47
44 30,341
38
[370]
[930]
[10]
[3023] [3464] [3689] [3905]
[4275]
42
105
342
391
483
417
441
123
12251
69
64 37,962
60
[281]
[871]
[12]
[2998] [3448] [3667] [3881]
[4264]
32
98
390
414
339
482
438
147
14673
89 45,486
94
83
[192]
[791]
[14]
[2955] [3406] [3631] [3852]
[4264]
22
89
385
410
334
482
435
171
17192
112 53,0
108
117
104
[148]
[738]
[15]
[3352] [3573] [3790]
[2887] Max.
[4189]
17
83
Contin-379
404
326
473
428
183
183
131
142 uous136 56,8
112
127
[3281] [3511]
[2816] Max.
[4135]
[3743]
[476]
[20]
397
318Inter-371
467
423
54
154
165
133
150
mittent159 75,7
243
[2773] [3243] [3475] [3705]
[4098]
366 [738]
393 Torque
313
419 [lb-in 463
]
171
165
177
160 Nm 146
83
183 Speed RPM
[2519] [3010] [3243] [3495]
366
285
340
395
226
238
231
209
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
Max.
Intermittent
53,0
[15]
56,8
[1560]
176
22
[1590]
180
48
[1578]
178
72
[1520]
172
97
[1467]
166
121
[1410]
159
145
[1338]
151
170
[1288]
146
182
75,7
[738]
83
183
[2034]
230
21
[2101]
237
48
[2096]
237
72
[2051]
232
97
[2001]
226
120
[1908]
216
145
[1851]
209
170
[1803]
204
182
[2501]
283
19
[2561]
289
47
[2564]
290
71
[2525]
285
96
[2477]
280
120
[2400]
271
145
[2338]
264
169
[2287]
258
181
[476] [1020] [1544] [2010]
54
115
174
227
243
242
242
241
[20]
}
}
Torque [lb-in ]
Nm
Speed RPM
[200]
14
370 cm3/r [22.6 in3/r]
[200]
14
[2]
7,6
[4]
15,1
[6]
low LPM [GPM]
Max.
Continuous
[499] [1035]
56
117
24
23
[497] [1052]
56
119
49
49
[480] [1031]
54
116
74
74
[427] [975]
48
110
99
98
[370] [930]
42
105
123
122
[281] [871]
32
98
147
146
[192] [791]
22
89
171
171
[148] [738]
17
83
183
183
Continuous
[800] [1000]
55
69
22,7
[8]
30,3
[10]
37,9
[12]
[590]
67
20
[588]
66
41
[580]
66
61
[514]
58
82
[444]
50
102
[337]
Continuous
[400] [600]
28
41
[1237]
140
19
[1263]
143
41
[1245]
141
60
[1164]
132
81
[1119]
126
102
[1062]
[1858]
210
18
[1906]
215
40
[1899]
215
60
[1824]
206
80
[1759]
199
101
[1690]
Max.
Continuous
[800] [1000] [1200] [1300]
55
69
83
90
[2406]
272
17
[2506]
283
40
[2506]
283
59
[2452]
277
79
[2391]
270
101
[2256]
[2953]
334
15
[3029]
342
39
[3029]
342
58
[2975]
336
78
[2928]
331
100
[2813]
[3388] [3586]
383
405
12
11
[3557] [3811]
402
431
38
37
[3544] [3788]
400
428
57
56
[3518] [3783]
397
427
77
77
[3479] [3750]
393
424
97
96
[3393] Max.
[3685]
Flow LPM [GPM]
Flow LPM [GPM]
15,1
[6]
[600]
41
Flow LPM [GPM]
[2]
7,6
[4]
[400]
28
[816] [1251] [1663] [2067] [2448]
92
141
188
277
234
303
301
300 Max.
292
297 Max.
InterContinuous mittent
306 [1800]
cm3/r [1850]
[18.7 in3[2250]
/r]
[1200] [1400] [1600] [1650]
83
110
125 Bar 127
155
97
114
∆ Pressure
[PSI]
Continuous
[2403] [2707] [2597] [2552] [2373] [2299]
[200] 306
[400] 293
[600] 288
[800] [1000]
[1200]
[1400]
272
268
260
97
1241
2214
1728
769
1155
683
[3177]
[2468]
[2820]
[3509]
[3261]
[3589]
[4194]
[499] [1035] [1560] [2034] [2501] [2912] [3239]
27956 319
474
117 359
176 368
230 396
283 406
329
366
5022
5724
5523
4619
4921
4416
35
11
[2477]
[4290]
[497] [2843]
[1052] [3196]
[1590] [3285]
[2101] [3547]
[2561] [3633]
[3023] [3464]
361
28056 321
401
485
371
410
119
180
237
289
342
391
7848
8649
8249
7247
60
7648
7147
44
[2454]
[3177]
[3530]
[4285]
[2820]
[3265]
[3615]
[480] [1031] [1578] [2096] [2564] [3023] [3464]
27754 319
484
116 359
178 369
237 399
290 408
342
391
11674 11374 10872 10672 10171
85
9969
64
[2412]
[4269]
[427] [2774]
[975] [3151]
[1520] [3241]
[2051] [3504]
[2525] [3593]
[2998] [3448]
27348 313
482
390
110 356
172 366
232 396
285 406
339
14699 14398 13697 13497 12796 12594
107
89
[2360]
[4237]
[370] [2734]
[930] [3105]
[1467] [3194]
[2001] [3466]
[2477] [3554]
[2955] [3406]
26742 309
479
385
105 351
166 361
226 392
280 402
334
177
134
112
123 173
122 166
121 163
120 156
120 153
117
[2298]
[4226]
[281] [2674]
[871] [3052]
[1410] [3148]
[1908] [3419]
[2400] [3510]
[2887] [3352]
26032 30298 345
477
379
159 356
216 386
271 397
326
207
161
136
147 202
146 195
145 193
145 185
145 182
142
[2261]
[4220]
[192] [2637]
[791] [3022]
[1338] [3116]
[1851] [3389]
[2338] [3488]
[2816] [3281]
25522 29889 341
477
371
151 352
209 383
264 394
318
222
174
171 217
159
171 209
170 207
170 200
169 197
165
Continuous
[800] [1000]
55
69
[2832] [2928] [3214] [3312
37
331
363
320
27
281
273
284
Max.
Continuous
[1500] [1600]
103
110
[2859]
323
8
[3680]
416
41
[3689]
417
62
[3667]
414
86
[3631]
410
108
[3573]
404
131
[3511]
397
154
[3475]
393
165
Max.
Intermittent
[1800]
124
[2400]
271
5
[3886]
439
38
[3905]
441
60
[3881]
438
83
[3852]
435
104
[3790]
428
127
[3743]
423
150
[3705]
419
160
[3243] [3495]
366
395
226
209
}
306 cm3/r [18.7 in3/r]
[200]
14
[372]
42
[20]
[833] [1260] [1655] [2038]
Max.
94 Max.
142
187
230
Inter29 Contin27
26
24
mittent
uous
[843] [1277] [1695] [2083]
[2]
[1800]
95 [1850]
144 [2250]
192
235
125
155 7,6
127
62
60
59
59
[823] [2299]
[1261] [1687] [2088]
[4]
[2373]
93
142
191
236
268
260
91
90
89
88
15,1
7
6
[787]
[1220]
[6]
[3509] [3589] [1651]
[4194] [2059]
89
138
187
396
406
474 233
122
121
12035 22,7
119
46
44
[744] [3633]
[1177] [1611]
[8]
[3547]
[4290] [2017]
84
133
182
401
485 228
410
152
151
150
148
30,3
72
60
71
[687] [3615]
[1132] [1553]
[10]
[3530]
[4285] [1967]
78
128
175
399
484 222
408
183
181
180
179
101
85 37,9
99
[628] [3593]
[1072] [1498]
[12]
[3504]
[4269] [1910]
71
121
169
396
482 216
406
213
212
211
209
127
107 45,4
125
[586] [3554]
[1035] [1458]
[14]
[3466]
[4237] [1872]
66
117
165
392
479 212
402
228
227
226
224
156
134 53,0
153
[148] [738] [1288] [1803] [2287] [2773] [3243]
[15]
Max.
[3419]
[4226]
[3510]
[372] [816] [1251] [1663] [2067]17 [2448]83 [2832]
204 [3214]
258 [3312]
313
366
146 [2928]
386
477 188
397
42
92Contin141
234
182 363
181 374
177
183 277
171
56,8
183 320
182 331
uous
185
161
182
305
303
301
300
292
281
270
297
284
273
[3389] [3488] Max.
[4220]
[1020]
[1544]
[2010]
[3010]
[476]
[2519]
[20]
383
394 Inter-477
115
174
227
340
285
200
174cm3/r [18.7 in3/r] 54
197 mittent
306
242 Max.
242 Max.
241
231
243
238
75,7
∆
Pressure
Bar
[PSI]
InterContin[2832] [2928] [3214] [3312]
Continuous
mittent
uous
Torque
[lb-in
]
[738]
331
374
320
363
Nm
83 [1200] [1400]
281
270
284
273
[1500] [1600]
[200]
[400]
[600]
[800] [1000]
[1800]
Speed
183
103
14
28
41
55
69
83 RPM97
124
110
7,6
[4]
[1600]
110
15,1
[6]
[2597]
293
22,712
[8]
[3177]
359
30,350
[10]
[3196]
361
37,978
[12]
[3177]
359
45,4
108
[14]
[3151]
356
53,0
136
[15]
[3105]
351
56,8
166
[3052]
[20]
345
195
75,7
[3022]
341
209
[406]
46
30
[404]
[1650]
46
114
62
[382]
[2552]
43
288
92
11
[341]
[3261]
39
368
123
49
[297]
[3285]
34
371
154
76
[225]
[3265]
25
369
184
106
[154]
[3241]
17
366
214
134
[119]
[3194]
13
361
229
163
[3148]
356
193
[3116]
352
207
213
212
211
209
207
185
202
195
18
193
[586] [1035] [1458] [1872] [2261] [2637] [3022] [3116] [3389] [3488
66
117
165
212
255
383
298
341
39
352
228
227
226
224
222
200
217
209
19
207
24475,7
cm3/r [14.9 in3305
/r]
[2]
[590]
Max.
67
Inter7,6
20
mittent
[4]
[588]
[1500]
66
15,1 103
41
[6]
[580]
66
22,7
61
[8]
[4252] [514]
58
480
82
30,3 36
[10]
[4300] [444]
50
486
37,9 54 102
[337]
[12]
[4284]
38
484
45,4 75 122
[14]
[4275] [231]
26
EATON
483 Low
53,0 93 142
[15]
[4273] [178]
[1560]
176
22
[1590]
180
48
[1578]
178
72
[1520]
172
97
[1467]
166
121
[1410]
159
145
[1338]
151
170
[1288]
146
182
[2034]
230
21
[2101]
237
48
[2096]
237
72
[2051]
232
97
[2001]
226
120
[1908]
216
145
[1851]
209
170
[1803]
204
182
[2501]
283
19
[2561]
289
47
[2564]
290
71
[2525]
285
96
[2477]
280
120
[2400]
271
145
[2338]
264
169
[2287]
258
181
[2912]
329
16
[3023]
342
47
[3023]
[2]
342
7,6 69
[2998]
[4]
339
15,1 94
[2955]
[6]
334
22,7117
[2887]
[8]
326
30,3142
[2816]
[10]
318
37,9165
[2773]
[12]
313
45,4177
[2519]
[1020] [1544] [2010] [14]
285
115
174
227
242
242
241 53,0238
[15]
Max.
Contin56,8
uous
Flow LPM [GPM]
Continuous
[800] [1000] [1200] [1400]
55
69
83
97
[2]
[600]
41
56,8
Flow LPM [GPM]
244 cm3/r [14.9 in3/r]
Flow LPM [GPM]
[400] [600]
designated with[200]a number
14
28
41
[833]a [1260]
best motor[2] life [406]
select
46
94
142
7,6 with
30 a torque
29
27
motor to run
[404]shown
[843] [1277]
and speed[4]range
in
46
95
144
the light shaded
area.62
15,1
62
60
[400]
28
214
[119]
13
229
53,0
[15]
Max.
Continuous
Max.
Inter-
[3239]
366
11
[3464]
[200]
391
14
44
[3464]
[590]
391
67
64
20
[3448]
[588]
390
66
89
41
[3406]
[580]
385
66
112
61
[3352]
[514]
379
58
136
82
[3281]
[444]
371
50
159
102
[3243]
[337]
366
38
171
122
[231]
[3010]
26
340
142
231
[178]
20
152
[2859]
[2400]
3/r [22.6 in3/r]
370 cm
271
∆323Pressure
8
5 Bar [PSI]
Continuous
[3680] [3886]
[4221]
[400]
416 [600]
439 [800]477[1000]
28
41
55 30 69
41
38
[4275]
[3689]
[3905]
[1237] [1858] [2406] [2953]
417
441
140
210
272483 334
62
60
19
18
17 51 15
[3667] [1906]
[4264] [3029]
[3881] [2506]
[1263]
414
438
143
215
283482 342
86
83
41
40
40 73 39
[3631] [1899]
[4264] [3029]
[3852] [2506]
[1245]
410
435
141
215
283482 342
108
104
60
60
59 92 58
[3573]
[4189] [2975]
[3790]
[1164] [1824] [2452]
404
428
132
206
277473 336
131
127
81
80
79112 78
[3511] [1759]
[4135] [2928]
[3743] [2391]
[1119]
397
423
126
199
270467 331
154
150
102
101
101133 100
[3475] [1690]
[4098] [2813]
[3705] [2256]
[1062]
393
419
120
191
255463 318
165
160
121
120
119146 119
[958]
[1608]
[2201]
[2748]
[3243] [3495]
108
182
249
310
366
395
141
140
139
138
226
209
[896] [1543] [2147] [2683]
101
174
243
303
152
151
150
149
Max.
Continuous
[1200] [1300]
83
90
[3388]
383
12
[3557]
402
38
[3544]
400
57
[3518]
397
77
[3479]
393
97
[3393]
383
118
[3319]
375
137
[3272]
370
147
[3586]
405
11
[3811]
431
37
[3788]
428
56
[3783]
427
77
[3750]
424
96
[3685]
416
116
[3610]
408
134
[3572]
404
146
Max.
Intermittent
[1500]
103
[4252]
480
36
[4300]
486
54
[4284]
484
75
[4275]
483
93
[4273]
483
112
[4198]
474
129
[4187]
473
140
[587] [1228] [1833] [2331] [2948] [3273]
333
66
139
207
263
370
198
202 Max.
201
201
200
196
Max.
InterContinuous mittent
[800] [1000] [1200] [1300]
[1500]
55
69
83
103
90
[20]
mittent
370 cm3/r
[22.6 in375,7
/r]
Continuous
[400] [600]
28
41
[1237]
140
19
[1263]
143
41
[1245]
141
60
[1164]
132
81
[1119]
126
102
[1062]
120
121
[958]
108
Speed
141
[896]
[1858] [2406]
210
272
18
17
[1906] [2506]
215
283
40
40
[1899] [2506]
215
283
60
59
[1824] [2452]
206
277
80
79
[1759] [2391]
199
270
101
101
[1690] [2256]
191
255
120
119
[1608] [2201]
182
249
High Torque
140
139
[1543] [2147]
[2953] [3388] [3586]
334
383
405
15
12
11
[3029] [3557] [3811]
[4252]
342
402
431
480
39
38
37
36
[3029] [3544] [3788]
[4300]
342
400
486
428
58
57
54
56
[2975] [3518] [3783]
[4284]
336
397
484
427
78
77
75
77
[2928] [3479] [3750]
[4275]
331
393
483
424
100
97
93
96
[2813] [3393] [3685]
[4273]
318
383
483
416
119
118
112
116
[2748] [3319] [3610]
[4198]
310
375
474 September 2011
408
Motors E-MOLO-MC001-E6
138
137
129
134
[2683] [3272] [3572]
[4187]
B-4-7
[4221]
477
30
[4275]
483
51
[4264]
482
73
[4264]
482
92
[4189]
473
112
[4135]
467
133
[4098]
463
146
B-4
T Series (158-)
Ports
Note:
Dimensions
7/8
-14 INF O-Ring Ports (2)
1/2
-14 NPTF (2)
Mounting Surface Flatness
Requirement is
,13
mm [.005 inch] Max.
(Refer to pages B-4-19 thru
dimensions.)
G 1/2 BSP (2)
Manifold Ports (5/16-18 mounting threads
2 Bolt Flange
82,55/82,42
[3.250/3.245]
Pilot Dia.
Geroler Width
X
E a ton
133,9
[5.27]
Max.
106,35
[4.187]
B Port
13,62/13,46
[.550/.530] Dia. Thru
(2) Mounting Holes
15,2
[.60]
98,3 [3.87] Max.
Mounting
Surface
2,8
[.11]
Standard Motor
End Cap
A Port
Y Max.
Groove Provided for 82,6 [3.25] I.D. x
2,62 [.103] Cross Section O-ring ( Dash No. 152)
Mounting
Surface
4 Bolt Flange
41,4
[1.63]
(2)
44,45/44,32
[1.750/1.745]
Pilot Dia.
85,9
[3.38]
Max.
(2)
45º
3/8-16 UNC (15,2 [.60] Max. Bolt Thread Engagement ) Mounting
or
B-4-8
2 and 4 Bolt Flange Port Dimensions
87,9
[3.46]
Max.
DisplacementX
cm3/r [in3/r]
mm [inch]
Y
mm [inch]
36 [2.2]
49 [3.0]
66 [4.0]
80 [4.9]
102 [6.2]
131 [8.0]
157 [9.6]
195 [11.9]
244 [14.9]
306 [18.7]
370 [22.6]
132,2 [5.21]
134,6 [5.30]
137,7 [5.42]
140,3 [5.53]
144,3 [5.68]
149,6 [5.89]
154,5 [6.09]
161,3 [6.35]
170,3 [6.71]
181,6 [7.16]
197,9 [7.79]
6,6 [.26]
9,1 [.36]
12,2 [.48]
14,7 [.58]
18,5 [.73]
24,1 [.95]
29,0 [1.14]
35,6 [1.40]
44,7 [1.76]
56,1 [2.21]
72,1 [2.84]
T Series (158-)
Use digit prefix—158- plus
four digit number from
number-—Example: 158-1067.
Product Numbers
without the three-digit
prefix.
Standard
Port
Mounting Shaft Size
36496680 102 131
157195
244306
370 [2.2][3.0][4.0][4.9] [6.2][8.0][9.6] [11.9]
[14.9][18.7]
[22.6]
-1537
-1034
-1035
-1538
-1036
-1037
-1038
-1039
-1040
1 in. Straight 7/8 -14 O-Ring 158- — —
w/Woodruff 1/2 NPTF
158- — —
-1540
-1026
-1027
-1541
-1028
-1029
-1030
-1031
-1032
Key
Manifold*
158—
—
-1543
-1042
-1043-1544-1044
-1045-1046
-1047-1048
2 Bolt
7/8 -14 O-Ring 158- — —
-1552
-1082
-1083
-1553
-1084
-1085
-1086
-1087
-1088
Flange
1 in. SAE 6B 1
/
2 NPTF
158—
—
-1555
-1074
-1075
-1556
-1076
-1077
-1078
-1079
-1080
Splined
Manifold* 158- —
— -1558 -1090 -1091-1559-1092 -1093-1094 -1095-1096
7/8 -14 O-Ring 158- — —
-1570
-1010
-1011
-1571
-1012
-1013
-1014
-1015
-1016
1 in. Straight
1
/
2
NPTF
158—
—
-1573
-1002
-1003
-1574
-1004
-1005
-1006
-1007
-1008
w/Woodruff
Key
Manifold*
158—
—
-1576
-1018
-1019-1577-1020
-1021-1022
-1023-1024
4 Bolt
7/8 -14 O-Ring 158- — —
Flange
-1579
-1058
-1059
-1580
-1060
-1061
-1062
-1063
-1064
1 in. SAE 6B 1/2 NPTF
158- — —
-1582
-1050
-1051
-1583
-1052
-1053
-1054
-1055
-1056
Splined
Manifold* 158- —
— -1585 -1066 -1067-1586-1068 -1069-1070 -1071-1072
B-4
158-1067
T Series Motors with Corrosion Protection
Port
Mounting shaftSize
36 49 66 80 102 131157195244306370 [2.2] [3.0][4.0][4.9][6.2][8.0][9.6][11.9][14.9][18.7][22.6]
2 Bolt
—
——1645
————-1649
—-1650
1 in. Straight 7/8 -14 O-Ring 158-
Flange
w/ Woodruff
1/2 NPTF
4 Bolt
Key
158- —
———————-1620
—-1621
Flange
158-1620
T Series Motors with Low Speed Valving
Port
Mounting Shaft Size
36 49 66 80 102131157195244306370
[2.2][3.0][4.0][4.9][6.2][8.0][9.6][11.9][14.9][18.7][22.6]
7
158- —
— — -1427-1428— — -1430-1431-1432-1433
1 in. Straight /8 -14 O-Ring
2 Bolt
158- —
— — -1419-1420— — -1422-1423-1424-1425
w/Woodruff 1/2 NPTF
Key
Manifold*
158—
——————————
Flange
7
/
8
-14
O-Ring
158—
——-1525
————-1675
——
1 in. SAE 6B
Splined
1/2 NPTF
158- —
———-1634
——————
158- —
——-1522
-2678
—————-1527
1 in. Straight Manifold*
4 Bolt
w/ Woodruff 7/8 -14 O-Ring
Flange
158- —
— -1625-1410-1411-1626-1412-1413-1414-1415-1416
1/2 NPTF
Key
158- —
— -1644-1402-1403— -1404-1405-1406-1407-1408
*Manifold product numbers shown are for
motors with four 5/16 -18 port face mounting
threads. Manifold, manifold mounting O-Rings
and bolts are NOT included.
For T Series Motors with a
configuration Not Shown
in the charts above: Use
the model code system on
page B-4-10 to specify the
product in detail.
158-1403
B-4-9
to identify all of the configuration options for the T motor.
T Series (158-)
Model Code
M
T 0
* * *
* *
* *
* *
*
*
*
* *
*
0
* *
*
*
0
A
1
2 3
4 5 6
7 8
9 10
11 12
13
14
15
16 17
18
19
20 21
22
23
24
25
1 Product
M – Motor
2 , 3 Product Series
T0 – T Series
cm3/r [in3/r]
022 – 35 [2.2]
030 – 49 [3.0]
040 – 65 [4.0]
82.50 [3.248] Dia. x 8.13
[.320] Pilot, 13.59 [.535]
Dia. Mounting Holes on
106.35 [4.187] Dia. B.C.,
w/o O-ring Groove
9 , 10 Output Shaft
Description
049 – 80 [4.9]
062 – 102 [6.2]
080 – 131 [8.0]
096 – 158 [9.6]
119 – 195 [11.9]
149 – 244 [14.9]
187 – 306 [18.7]
226 – 370 [22.6]
7 , 8 Mounting Type
82,6 [3.248] Dia. and 3,05
[.120] pilot, 13,59 [.535]
Dia. Mounting Holes
106,35 [4.187] Dia. B.C.
44,40 [1.748] Dia. x 3,05
[.120] pilot, .375-16
UNC-2B Mounting Holes
82,55 [3.250] Dia. B.C.
82,50 [3.248] Dia. x 6,10
[.240] pilot, 10,41 [.410]
Dia. Mounting Holes 106,35
[4.187] Dia. B.C. (SAE A)
DD – 2 Bolt (Std.) 101,60
[4.000] Dia. x 6.10 [.240]
pilot, 14,35 [.565] Dia.
Mounting Holes 146,05
[5.750] Dia. B.C. (SAE B)
(Ductile)
EA – 4 Bolt Magneto 82,50
[3.248] Dia. x 3,05 [.120]
Pilot, 13,59 [.535] Dia.
[4.187] Dia. B.C.
B-4-10
44,40 [1.748] Dia. x 3,05
[.120] pilot, M10 x 1.5-6H
[3.250] Dia. B.C.
11 , 12 Port Type
AA – .875-14 UNF-2B SAE
O-Ring Ports
Pipe Thread Ports
AC – Manifold (.3125-18
UNC-2B Mounting Holes)
AD – Manifold Ports (MB x
Thread Ports
No Lead Wire with M12
Connector
(A=Power, B=Common,
C=Signal)
Options
19 Valve
0 – None
(Hardware)
01 – 25,4 [1.00] Dia.
Shaft End
SS – Stainless Steel Flange
Bolts
02 – 25,4 [1.00] Dia. SAE
6B Spline, .25-20 UNC-2B
Hole in Shaft End
2–G
BSP Straight
Thread Port (End Cap)
0 – None
07 – 25,4 [1.00] Dia. Straight,
8,03 [.316] Dia. Crosshole
11,2 [.44] from End, 5,6 [.22]
Extra Length
A – Internal Check Valves
A – Reverse Rotation
Options
14 Geroler
0 – None
08 – 25,4 [1.00] Dia.
Straight, 10,31 [.406] Dia.
Crosshole 15,7 [.62] from
in Shaft End
A – Free Running
16 – 22,22 [.875] Dia. SAE
17 – 22,22 [.875] Straight
Dia. 6,4 [2.5] x 19,0 [.75]
Square Key (SAE B)
18 – 25,4 [1.00] Dia. Tapered,
Woodruff Key and Nut,
34,92 [1.375] Taper Length
24 – 25.00 [.984] Dia.
MB x 1.25-6H Hole in Shaft
End
39 - 25.00 [.984] Dia.
Straight (k6), 8.00 [.315]
Key, M8 x 1.25-6H Hole in
Shaft End
1 – .4375-20 UNF-2B SAE
1/4
Assembly
22 Special
Instructions
2 – Flange Rotation 90°
23 Paint/Packaging
Options
0 – No Paint
Options
15 Shaft
0 – None
A – Low Gloss Black
Primer
Gloss White
02 – Seal Guard
03 – Viton Seals
ID/
24 Customer
Nameplate Options
Code
25 Design
A – One (1)
Seal
Sensor Options
18 Speed
0 – None
A – 12 mm Digital Speed
Pickup (15 Pulse) without
Lead Wire
T Series with
Parking Brake (185-)
Features
• Integrated, Compact,
Patented Design
• Capability of Combining
4 inventory items into a
single assembly (motor,
brake, counter-balance
valve, brake release line)
Highlights
• Rear-mounted integrated
brake with 6:1 torque
advantage
• Access port for manual
brake release (for over-riding brake in the event of
loss of release pressure.)
Benefits
• Cost-effective Packaged
System Solution
• Simplifies ordering and
inventory requirements
Description
Eaton’s latest offering in LSHT motor technology is
the new T Series Motor with Parking Brake.
T Series Motor with Parking Brake utilizes brake pads that
rotate at 6 times the speed of the output shaft, thereby
giving the brake a 6-to-1 mechanical advantage. The T Series
Motor with Parking Brake utilizes the same Geroler‚ and
Spool Valve technologies as the standard Char-Lynn motors.
Therefore, in addition to providing dependable load-holding
capability, T Series Motor with Parking Brake provides the
same smooth, reliable operation, with similar performance,
as the T Series Motor.
Specifications
• Reduces assembly labor
• Design Flexibility
• Wet brake is environmentally protected and provides long life
Applications
• Truck-Mounted Equipment
(boom rotate and winch)
• Conveyors – Positioners –
Indexers
• Marine Cranes
(boom rotate and winch)
• Fishing Winches
Geroler Element
11 Displacements
Flow l/min [GPM]
55 [15] Continuous
• Recycling and Refuse
Equipment
75 [20] Intermittent
• Vehicle Recovery Winches
Speed
Up to 1055 RPM
• Mining Equipment
Pressure bar [PSI]
155 [2250] Cont.
• Specialty Utility Vehicles/
Machines
190 [2750] Inter.
Torque Nm [lb-in]
441 [3905] Cont.
486 [4300] Inter.
• Forestry Grapples
• Agricultural Equipment
• Railroad Equipment
• Airport Support Vehicles
• Lawn & Turf Equipment
• Anywhere Load-Holding is
Needed in a Low-Speed
High-Torque Drive System
Crane and winches
Boom Lift (Swing)
Maintenance Equipment
B-4-11
B-4
T Series with
Parking Brake (185-)
Application Information
Principle of Operation
The wet brake is a springapplied / pressure release
design. Load-holding is
applied by a mechanical
spring and released by
hydraulic pressure. The
spring force holds the brake
on when hydraulic pressure
is absent.
Release Pressure
Release pressure is defined
as the amount of pressure
required to fully release the
brake. The brake pressure
cavity is common (shared)
with the motor case. As a
result, maximum release
pressure is constrained by
the motor case-pressure
capability. The T Series
Motor with Parking Brake
incorporates a shaft seal
capable up to 1500 psi (see
page B-4-15). However, seal
life is reduced at higher case
pressure.
Residual Pressure
Residual pressure is the
pressure trapped in the
system by restrictions or
long return lines.
Residual pressure in the
motor case will lower the
rated load holding torque of
the brake.
Therefore, special attention
needs to be given when
applying this product. Keep
in mind that long return lines
create higher pressure that
will reduce brake holding
torque. In applications with
high system pressures,
the use of a pressure
reducing valve to limit case
and release pressure is
recommended.
Holding Torque and Motor
Output Torque
Typical Applications
Holding torque is based on
grade holding requirements
for a vehicle or other load
holding requirements in the
application. System pressure
and motor displacement are
the factors in determining
motor output torque. Motor
displacement, measured in
cubic centimeters or cubic
inches, is the volume of
fluid required to make one
revolution. Motor output
torque is the rotary force
and is usually measured in
inch pounds, newton meters
or foot pounds. Maximum
motor torque depends
on pressure and motor
displacement. Both output
shaft size and shaft type can
also affect motor torque. The
T Series Motor with Parking
Brake load holding capacity
is factory set to match
any limiting factor in each
specific motor configuration
(e.g. displacement, output
shaft, etc).
Winch
Gear
Reduction
Machine Drive
Gear
Reduction
T-Brake/Motor
Chain
Sprocket
Note:
Eaton Corporation does not
approve any products for
customer applications. It
is the sole responsibility of
the customer to qualify and
verify the correct operation
of products in their systems.
Note:
Special attention should
be given to system back
pressure. System back
pressure directly affects
brake release pressure
and can cause the brake
to release at undesired
conditions.
Swing Boom
T-Brake/Motor
Boom
Gear
Reduction
Pinion
Gear
Note:
The T Series with parking
brake is not compatible with
water based fluids.
B-4-12
Driven
Load
T-Brake/Motor
Bull or Slew Gear
T Series with Parking
Brake (185-)
Specifications
Shaft
Seal
Thrust
Bearing
Race
Thrust
Bearing
Housing
Drive
Spacer
Plate
Combination
Brake Release
Case Drain Port
Brake
Pad
Ass'y Piston
Springs
Brake
Shaft
Manual
Brake
Release
Access
Port
Exclusion
Seal
End Cap
Flange
B-4
Cap Screws
Geroler
®
Drive
Collar
Washers
Specification Data — T Series with Parking Brake Motors
Displ. cm 3/r
[in 3 /r]
36 [2.2]
49 [3.0] 66 [4.0] 80 [4.9] 102 [6.2] 131 [8.0] 157 [9.6] 195 [11.9] 244 [14.9] 306 [18.7] 370 [22.6]
Max. Speed (RPM) @
1021906849 694 550426355287229183 152
Continuous Flow
Flow
Continuous 38 [10]
45 [12] 57 [15]
57 [15]
57 [15] 57 [15] 57 [15] 57 [15] 57 [15] 57 [15]
57 [15]
LPM
Intermittent 38 [10]
57 [15] 68 [18]
76 [20]
76 [20] 76 [20] 76 [20] 76 [20] 76 [20] 76 [20]
76 [20]
[GPM]
Torque Continuous 76 [672] 105 [928] 138 [1222 174 [1541] 219 [1936]251 [2226]297 [2628]359 [3178]410 [3633]441 [3905] 430 [3811]
Nm
Intermittent **93 [824] 118 [1131]168 [1488] 212 [1872] 264 [2339]307 [2718]359 [3178]437 [3864]485 [4290]483 [4275] 486 [4300]
[lb-in]
PressureContinuous * 155 [2250] 155 [2250]155 [2250] 155 [2250] 155 [2250]138 [2000]138 [2000]138 [2000]127 [1850]110 [1600] 90 [1300]
∆ Bar Intermittent * **190 [2750]190 [2750]190 [2750] 190 [2750] 190 [2750]172 [2500]172 [2500]172 [2500]155 [2250]124 [1800] 103 [1500]
[∆ PSI]
Note:
See page B-4-2 for additional motor specification notes and
definitions. The T Series with Parking Brake performance
is similar to the standard T Series motor. High speed
conditions may reduce performance on T Series with
Parking Brake.
T Series Brake Holding Torque Settings:
Shaft
Output Shaft
CodeDescription
2.23.04.04.96.28.09.611.914.918.722.6
18
02
24
01
07
08
16
17
2,0002,0002,0003,5003,5003,5005,0005,0005,0005,0005,000
2,0002,0002,0003,5003,5003,5005,0005,0005,0005,0005,000
2,0002,0002,0003,5003,5003,5003,5003,5003,5003,5003,500
2,0002,0002,0003,5003,5003,5003,5003,5003,5003,5003,500
2,0002,0002,0003,5003,5003,5003,5003,5003,5003,5003,500
2,0002,0002,0003,5003,5003,5003,5003,5003,5003,5003,500
2,0002,0002,0002,0002,0002,0002,0002,0002,0002,0002,000
2,0002,0002,0002,0002,0002,0002,0002,0002,0002,0002,000
in-lbs
[in 3 /r]
1 Tapered w/key and nut
1 SAE 6B Splined
25mm Straight w/key
1 Straight w/key
1 Straight w/.31 dia. crosshole
1 Straight w/.40 dia. crosshole
7/8 SAE B 13T Splined
7/8 SAE B Straight w/key
Full Capacity Brake
in-lbs
Limited Capacity Brake
Note:
The factory setting values are used
for each motor based on motor
displacement and shaft type. Average
Static torque may vary +/- 14% from
rated values.
B-4-13
Brake (185-)
Dimensions
(Refer to pages B-4-19 thru B-4-22 for
shaft and port dimensions.)
For shaft configuration see
separate shaft drawing
106.35
Ø(4.187)
Port B
For port configuration see
separate port drawing
4.20
Ø (106.7) Max
88.9
(3.50)
Max
133.9
(5.27)
7/16+20 UNF-2B
O-Ring Port,
size 4 brake
release port
58.5
Ø 98,3 Max
(3.87)
2x Ø 13.59 +0.38
-0.13
( Ø .535 +.015 )
-.005
+0.05
82.50 -0.08
Ø
+.002
( 3.248 -.003 )
Port A
-E-
Ø
15.20.3
2.80.5 (060.01)
(0.11.02)
Y
-F-
X
7/16-20 UNF-2B O-ring port, size 4 manual
brake release access port when required
remove O-ring plug.
Use 5/16-24 UNF bolt stud and nut (not
included) to manually release the brake.
(Note: for emergency towing/servicing only)
T-Series with Parking Brake Dimensions
42,9
[1.69]
(2)
85,8
[3.38]
Max. (2)
44,45/44,32
[1.750/1.745]
Pilot Dia.
45
87,9
[3.46]
Max.
3/8-16 UNC (15,2 [.60] max.
bolt thread engagement
Mounting holes (4) equally spaced
on 82,6 [3.25] dia. bolt circle
or M10 x 1,5 (15,2 [.60] max.
bolt thread engagement
Mounting holes (4) equally
spaced on 82,6 [3.25] dia. bolt circle
DisplacementX
Y
mm [inch]
mm [inch]
cm3/r [in3/r]
02
A2
03
A3
04
05
06
08
10
12
15
19
23
190.2 [7.49]
190.8 [7.51]
192.5 [7.58]
194.3 [7.65]
195.6 [7.70]
198.4 [7.81]
202.2 [7.96]
207.5 [8.17]
212.6 [8.37]
219.2 [8.63]
228.3 [8.99]
239.5 [9.43]
251.2 [9.89]
143.9±0.9 [5.66±0.3]
144.5±0.9 [5.69±0.3]
146.3±0.9 [5.76±0.3]
148.1±0.9 [5.83±0.3]
149.3±0.9 [5.88±0.3]
152.0±0.9 [5.98±0.3]
155.9±0.9 [6.14±0.3]
161.3±0.9 [6.35±0.3]
166.2±0.9 [6.54±0.3]
172.9±0.9 [6.81±0.3]
181.9±0.9 [7.16±0.3]
193.3±0.9 [7.61±0.3]
205.0±0.9 [8.07±0.3]
Note:
Standard Rotation
When facing shaft end
of motor shaft to rotate
clockwise when port “A
is pressurized, counterclockwise when port “B
is pressurized
B-4-14
Reverse Rotation
When facing shaft end
of motor shaft will rotate
clockwise when port “B
is pressurized, counterclockwise when port “A
is pressurized
Brake (185-)
Brake Release and Motor Case
Pressure
The T Series Motor with
Parking Brake is durable
and has long life as long
as the recommended case
pressure is not exceeded.
Allowable case pressure is
highest at low shaft speeds.
Motor life will be shortened
if case pressure exceeds
recommended ratings
(acceptability may vary with
application).
Refer to the Case Pressure/
Shaft Seal chart below.
This chart is based on case
pressure and motor shaft
speed. A minimum release
pressure of 17 Bar [250 PSI]
must be maintained to fully
release the brake.
B-4
PC
.6 DP + P 2
P C = Case Pressure
P 1 = Inlet Line Pressure
P 2 = Back Pressure
DP = P 1 – P 2
Max. Axial Loads
454 kg [1000 lb]
Case Pressure/Shaft Seal
150
[2000]
103
[1500] 100
[1500]
Case
Pressure
[PSI]
[1000]
Pressure Reducing/Relieving
Valve Required
Pressure-Reducing/
Relieving Valve Recommended
50
[ 500]
0
Pressure-Reducing/
Relieving Valve
Required
0
0
0
Speed RPM
100
200
300
400
500
600
700
800
900 1000
B-4-15
Brake (185-)
185 plus four digit number
product number —
Example 185-2068.
Product Numbers
Standard Valving
Port
mountingShaft Size
3.0 4.04.96.28.09.611.914.918.722.6
7/8-14 O-Ring185-2000
200120022003200420052006200720082009
1 Keyed
Manifold 185-2010
201120122013201420152016201720182019
7/8-14 O-Ring185-2020
202120222023202420252026202720282029
2-Bolt
6B Splined Manifold 185-2030
203120322033203420352036203720382039
13T Splined 7/8-14 O-Ring185-2040
204120422043204420452046204720482049
16/32 pitch
Manifold 185-2050
205120522053205420552056205720582059
7/8-14 O-Ring185-2060
206120622063206420652066206720682069
1 Keyed
Manifold 185-2070
207120722073207420752076207720782079
4-Bolt
7/8-14 O-Ring185-2080
208120822083208420852086208720882089
209120922093209420952096209720982099
13T Splined 7/8-14 O-Ring185-2100
210121022103210421052106210721082109
16/32 pitch
Manifold 185-2110
211121122113211421152116211721182119
7/8-14 O-Ring185-2120
212121222123212421252126212721282129
1 Keyed
Manifold 185-2130
213121322133213421352136213721382139
2-Bolt
7/8-14 O-Ring185-2140
214121422143214421452146214721482149
SAE
B
215121522153215421552156215721582159
13T Splined 7/8-14 O-Ring185-2160
216121622163216421652166216721682169
16/32 pitch
Manifold 185-2170
217121722173217421752176217721782179
Low Speed Valving
Port
mountingShaft Size
3.0 4.04.96.28.09.611.914.918.722.6
7/8-14 O-Ring
1 Keyed
185-2180
218121822183218421852186218721882189
Manifold 185-2190
219121922193219421952196219721982199
2-Bolt
6B Splined 7/8-14 O-Ring185-2200
220122022203220422052206220722082209
Manifold 185-2210
221122122213221422152216221722182219
13T Splined 7/8-14 O-Ring185-2220
222122222223222422252226222722282229
16/32 pitch
Manifold 185-2230
22312232223322342235223622372238223
7/8-14 O-Ring
1 Keyed
185-2240
224122422243224422452246224722482249
Manifold 185-2250
225122522253225422552256225722582259
4-Bolt
226122622263226422652266226722682269
Manifold 185-2270
227122722273227422752276227722782279
13T Splined 7/8-14 O-Ring185-2280
228122822283228422852286228722882289
16/32 pitch
Manifold 185-2290
229122922293229422952296229722982299
7/8-14 O-Ring
1 Keyed
185-2300
230123022303230423052306230723082309
Manifold 185-2310
231123122313231423152316231723182319
2-Bolt
232123222323232423252326232723282329
SAE B
Manifold 185-2330
233123322333233423352336233723382339
13T Splined 7/8-14 O-Ring185-2340
234123422343234423452346234723482349
16/32 pitch
Manifold 185-2350
235123522353235423552356235723582359
185-2357
Motors with the low speed
valving option enable very
smooth low speed operation
while maintaining high
torque.
Designed to run
continuously at up to 200
RPM at standard rated
pressures and reduced
B-4-16
flows, this option provides
smooth operation at low
speeds. Furthermore, they
resist slippage and have
more momentary load
holding ability than the
standard motors.
Motors with this valving
are not intended for low
pressure applications
(A minimum of 300 psi
delta must be maintained
between A port pressure
and case pressure).
Shaft side / radial load
ratings are not affected by
this valving.
For a T Series motor with
parking brake configuration
not shown in the charts
above use the model code
system on page B-4-17 to
specify the product in detail.
Brake (185-)
to identify all of the configuration options for the T Series
Motor with Parking Brake. Use this model code to specify
a motor with the desired features. All 25-digits of the
code must be present when ordering. You may want to
photocopy the matrix below to ensure that each number is
entered in the correct box.
Model Code
MT B
1
2 3
* * *
* *
* *
* *
*
*
*
* *
*
0
* *
*
*
0
B
4 5 6
7 8
9 10
11 12
13
14
15
16 17
18
19
20 21
22
23
24
25
1 Product
M – Motor
2 , 3 Series
T B – T Series Motor with
Parking Brake
4 , 5 , 6
Displacement
cm3/r [in3/r]
022 – 36 [2.2]
030 – 49 [3.0]
040 – 66 [4.0]
049 – 80 [4.9]
062 – 102 [6.2]
080 – 131 [8.0]
096 – 157 [9.6]
119 – 195 [11.9]
149 – 244 [14.9]
187 – 306 [18.7]
226 – 370 [22.6]
7 , 8 Mounting Type
82,5 [3.248] Dia. and 3,05
[.120] pilot, 13,59 [.535]
[4.187] Dia. B.C.
44,40 [1.748] Dia. x 3,05
[.120] pilot, .375-16 UNC-2B
[3.250] Dia. B.C.
82,50 [3.248] Dia. x 6,10
[.240] pilot, 10,41 [.410]
[4.187] Dia. B.C. (SAE A)
DA – 2 Bolt (Std.) 101,60
[4.000] Dia. x 6.10 [.240]
pilot, 14,35 [.565] Dia.
[5.750] Dia. B.C. (SAE B)
11 , 12 Port Type
Options
19 Valve
AA – .875-14 UNF-2B SAE
O-Ring Ports
0 – None
EA – 4 Bolt Magneto 82,50
[3.248] Dia. x 3,05 [.120]
Pilot, 13,59 [.535] Dia.
[4.187] Dia. B.C.
Pipe Thread Ports
(Hardware)
AC – Manifold (.3125-18
UNC-2B Mounting Holes)
44,40 [1.748] Dia. x 3,05
[.120] pilot, M10 x 1.5-6H
[3.250] Dia. B.C.
9 , 10 Output Shaft
Description
01 – 25,4 [1.00] Dia. Straight,
Woodruff Key, .250-20
UNC-2B Hole in Shaft End
02 – 25,4 [1.00] Dia. SAE 6B
Spline, .25-20 UNC-2B Hole
in Shaft End
16 – SAE 13 Tooth Spline,
16/32 Pitch, 21,74 (.856) Dia.
(SAE B)
18 – 25,4 [1.00] Dia. Tapered,
Woodruff Key
and Nut, 34,92 [1.375]
Taper Length
24 – 25.00 [.984] Dia.
MB x 1.25-6H Hole in
Shaft End
AD – Manifold Ports (MB x
3 – Manifold Case Drain
Options
14 Geroler
A – Standard
B – Free Running
Assembly
22 Special
Instructions
0 – None
2 – Flange Rotation 90°
23 Paint/Packaging
Options
0 – No Paint
Options
15 Shaft
0 – None
ID/
24 Customer
Nameplate Options
Code
25 Design
B – Two (2)
03 – Viton Seals
Seal
Sensor Options
18 Speed
0 – None
A – 12 mm Digital Speed
Pickup (15 Pulse) without
Lead Wire
(A=Power, B=Common,
C=Signal)
B-4-17
B-4
Case Pressure and Case
Drain — H, S, and T Series
from the case pressure
seal limitation chart below
— chart based on case
pressure and shaft speed. If
a case drain line is needed,
connect drain line to assure
that the motor will always
remain full of fluid. A
pressure restriction should
be added to the case drain
line, during which a motor
case pressure of 3,5 Bar [50
PSI] is maintained.
Char-Lynn H Series, S Series
and T Series motors are
durable and have long life as
long as the recommended
case pressure is not
exceeded. Allowable case
pressure is highest at low
shaft speeds. Consequently,
motor life will be shortened
if case pressure exceeds
these ratings (acceptability
may vary with application).
Determine if an external
case drain is required
H Series
S Series
Max. Axial Loads
454 kg [1000 lb]
T Series
150
[2000]
[1500]
Case
Pressure
Bar
50
[PSI]
[1000]
0
Case Drain
Required
Intermittent —
Case Drain
Optional
Continuous —
Case Drain
Optional
[ 500]
0
0
0
100
200
300
400
500
600
700
800
900 1000
Speed RPM
B-4-18
P1
P2
Pc
P2
Pc
P C .6 ∆P + P 2
P C = Case Pressure
P 1 = Inlet Line Pressure
P 2 = Back Pressure
∆P = P 1 – P 2
Thrust Load
103
[1500] 100
P1
P1
P2
Pc
H, S and T Series
(101-, 103-, 158-, 185-)
Side Load Capacity
The hydrodynamic bearing
has infinite life when
shaft load ratings are not
exceeded. Hence, the shaft
side load capacity is more
than adequate to handle
most externally applied
loads (such as belts, chains,
etc.), providing the motor to
shaft size is applied within
its torque rating. determine the shaft side
load capacity at locations
other than those shown use
the formula (shown below).
Allowable side load chart,
shaft load location drawing
and load curves (below) are
based on the side / radial
loads being applied to shaft
at locations A, B, and C, to
When the speed sensor
option is used, side
load ratings are reduced
25%. Sideload P kg =
Sideload P [lb] =
For more information
about shaft side loads on
Char-Lynn motors contact
your Eaton representative. A
B
C
900 625 500 400 300 200 154 [ 339] 205 [ 452] 256 [ 565] 307 [ 678] 410 [ 904] 718 [1582] 136 [ 300] 181 [ 400] 227 [ 500] 272 [ 600] 363 [ 800] 635 [1400] 118 [ 261]
158 [ 348]
197 [ 435]
237 [ 522]
316 [ 696]
552 [1216]
B-3
B-4
Note:
900
16800
N
L + 96,3
900
1460
N
B-2
RPM Allowable Shaft Side Load — Kg [lb]
L + [3.79]
for 200-900 RPM
L
for 200-900 RPM
45,2 [1.78]
26,9 [1.06]
P
Where N = Shaft Speed (RPM)
L = Distance from Mounting Surface
kg
800
718 [1582]
635 [1400]
700
600
552 [1216]
500
Shaft
Side
400
Load
kg [lb]
300
200
100
0
C
12,7 [ .50]
B
A
[lb]
[1600]
A
[1400]
B
[1200]
Mounting
Surface *
* 2 Bolt SAE B mounting flange has a greater pilot
thickness and a thinner mounting plate (end of shaft
to flange, add 3,3 [.13]).
C
[1000]
[ 800]
[ 600]
[ 400]
[ 200]
0
100
0
0
Shaft Speed (RPM)
200
300
400
500
600
700
800
900
B-4-19
H, S and T Series
(101, 103- 158, 185)
Dimensions
Shafts
Shaft
Torque Nm
[lb-in]
Shaft Size
Option
Shaft
Motor Torque
Option
Combination1 Shaft
inch Dia. Tapered with Woodruff Key and Nu t
6B Splined
Option
Limit Guide SAE
Torque Nm
[lb-in]
1 inch Dia. Tapered with Woodruff Key and Nu t
25mm w/KeywaySAE
and6B1 Splined
inch Dia. Straight w/Keyway
inch Dia.
Dia. Straight
Dia. Crosshole
11 inch
Taperedwith
with.315
Woodruff
Key and Nu t
1 inch6BDia.
Straight
with
.406 Dia. and
Crosshole
25mm
w/Keyway
1 inch Dia. Straight w/Keyway
SAE
Splined
1 inch Dia. Straight with .315 Dia. Crosshole
7/8
inch
Straight
with
Key
25mm w/Keyway1 inch
and 1Dia.
inchStraight
Dia. Straight
w/Keyway
with .406
Dia. Crosshole
1 inch
Dia.
Straight
with .315 Dia. Crosshole
7/8
inch
SAE
B 13T Splined
7/8 with
inch Straight
Key
1 inch Dia. Straight
.406 Dia.with
Crosshole
7/8
inch
SAE
B
13T
Splined
7/8 inch Straight with Key
7/8 inch SAE B 13T
Splined
Mounting
Surface *
46,0/44,5
1 in. Dia.[1.81/1.75]
Straight
with Woodruff Key46,0/44,5
Mounting
[1.81/1.75]
Surface *
46,0/44,5
[1.81/1.75]
19,1/18,0
[.75/.71]
19,1/18,0
[.75/.71]
19,1/18,0
[.75/.71]
100
[1000]
Torque Nm
[lb-in]
100
[1000]
Mounting
Surface *
6,6/4,6
[.26/.18]
11,7/10,7
51,6/50,0
[.46/.42]
[2.03/1.97]
11,7/10,7
[.46/.42]
25,40/25,37
[1.000/.999]
Dia.
25,40/25,37
[1.000/.999]
Dia.
B-4-20
Mounting
51,6/50,0
Surface *
[2.03/1.97]
11,7/10,7
[.46/.42]
25,40/25,37
[1.000/.999]
Dia.
8,08/7,92
[.318/.312]
Dia. Thru
8,08/7,92
[.318/.312]
Dia. Thru
300
200
300
SAE 6B46,0/44,5
Splined Shaft
[1.81/1.75]
Mounting
46,0/44,5
Surface *
24,5 [1.00] Min. [1.81/1.75]
6,6/4,6
46,0/44,5
Full
Spline Depth
25,40/25,15 [1.000/.990]
[.26/.18]
[1.81/1.75] 24,5 [1.00] Min.
Dia.6,6/4,6
Key x 6,375/6,350
Full Spline Depth
[.26/.18] Wide
[.2510/.2500]
25,40/25,15 [1.000/.990]
24,5 [1.00] Min.
Dia. Key x 6,375/6,350
Full Spline Depth
25,40/25,15 [1.000/.990]
[.2510/.2500] Wide
Dia. Key x 6,375/6,350
[.2510/.2500] Wide
25,35/25,30
[.998/.996]
Dia.
25,35/25,30
[.998/.996]
Dia.
[3000]
[2000]
[3000]
400
300
400
Mounting
Surface *
6,9/4,8
[.27/.19]
6,9/4,8
[.27/.19]
[4000]
[3000]
400
[4000]
[4000]
6,9/4,8
[.27/.19]
25,35/25,30
[.998/.996]
1/4-20 UNC-2B
Dia. x 14,2 [.56] Min. Deep
1/4-20 UNC-2B
x 14,2 [.56] Min. Deep
1/4-20 UNC-2B
x 14,2 [.56] Min. Deep
1 in. Dia. Straight Shaft
with .406 Dia. Crosshole
1 in. Dia. Straight Shaft with
.315 Dia. Crosshole
51,6/50,0
[2.03/1.97]
[2000]
100
[1000]
200
[2000]
Mounting
Surface *
28,30/27,89
[1.114/1.098]
28,30/27,89
25,40/25,37
[1.114/1.098] 1/4-20 UNC-2B
[1.000/.999]
28,30/27,89
x 14,2 [.56] Min. Deep
Dia.
25,40/25,37
[1.114/1.098]
1/4-20 UNC-2B
[1.000/.999]
x 14,2 [.56] Min. Deep
25,40/25,37 Dia.
1/4-20 UNC-2B
[1.000/.999]
x 14,2 [.56] Min. Deep
Dia.
Mounting
Surface *
200
Mounting
Surface
6,6/4,6
*
[.26/.18]
6,6/4,6
[.26/.18]
46,0/44,5
[1.81/1.75]
6,6/4,6
[.26/.18]
16,3/15,2
46,0/44,5
[.64/.60]
[1.81/1.75]
16,3/15,2
[.64/.60]
25,40/25,37
[1.000/.999]
Dia.
8,08/7,92
[.318/.312]
25,40/25,37
Dia. Thru
* 2 Bolt SAE B mounting flange has a greater
[1.000/.999]
pilot thickness and a thinner mounting plate
Dia.
(end of shaft to flange, add 3,3 [.13]).
Mounting
Surface *
Mounting
46,0/44,5
Surface *
[1.81/1.75]
16,3/15,2
[.64/.60]
Mounting
Surface6,6/4,6
*
[.26/.18]
6,6/4,6
[.26/.18]
6,6/4,6
[.26/.18]
10,44/10,19
1/4-20 UNC-2B
[.411/.401]
x 14,2 [.56] Min.
Deep
1/4-20 UNC-2B Dia. Thru
25,40/25,37
x 14,2 [.56] Min.
[1.000/.999]
10,44/10,19
Dia. 1/4-20 UNC-2B Deep
[.411/.401]
x 14,2 [.56] Min.
Dia. Thru
Deep
10,44/10,19
[.411/.401]
Dia. Thru
H, S and T Series
(101-, 103- 158-, 185-)
Dimensions
Shafts
1 in. Dia. Tapered
Shaft with Woodruff
Key and Nut
25,40/25,15
x 6,38/6,35
25,40/25,15
x 6,38/6,35
[1.000/.990
x .251/.250]
[1.000/.990
x .251/.250]
Woodruff
Ke y Ke y
Woodruff
Mou ntin
Moug ntin g
Surface
Surface
*
*
61,8/60,2
61,8/60,2
3/4-163/4-16
UNF-2A
UNF-2A
Slot ted
Slot
Hex.
tedNut
Hex. Nut
[2.43/2.37]
[2.43/2.37]
8,4/7,18,4/7,1
16,0 [.63]
16,0 Thick
[.63] 28,12
Thick 28,12
[1.107][1.107]
AcrossAcross
Flats Flats
25,40/25,15
x 6,38/6,35
[.33/.28]
[.33/.28]
Recommended
Recommended
Torque
Torque
:
: 25,40/25,15 x 6,38/6,35
37,1 37,1
[1.000/.990
xft].251/.250]
(203 Nm
(203[150
Nmlb[150
lbDry)
ft] Dry) [1.000/.990 x .251/.250]
[1.46] [1.46]
Woodruff
Keft]ylb(169 Nm
(169[125
Nmlb[125
Lubft]) LubMou
) Woodruff
Couplin
Couplin
gntin gg
ntin g Ke y
Mou
Plus torque
Plus torque
required
required
to align
to align
WidtSurface
hWidt h* 34,93 34,93
Surface *
slottedslotted
nut with
nutthe
with
shaft
the shaft
[1.375][1.375]
61,8/60,2
61,8/60,2
crosshole
crosshole
6 UNF-2A Slot ted Hex.3/4-16
Nut UNF-2A Slot ted[2.43/2.37]
Hex. Nut
[2.43/2.37]
8,4/7,1
.63] Thick 28,12 [1.107]16,0
Across
[.63] Flats
Thick 28,12 [1.107] Across Flats 8,4/7,1
50,6/49/,0
[.33/.28] 37,1
[.33/.28]
mmended Torque : Recommended Torque : 37,1
[1.99/1.93]
4,06/3,81
4,06/3,81
Nm [150 lb- ft] Dry) (203 Nm [150 lb- ft] Dry) [1.46]
[1.46]
[.160/.150]
[.160/.150]
Nm [125 lb- ft] Lub ) (169 Nm [125 lb- ft] Lub ) Couplin
g
Couplin g
Dia. Thru
orque required to align Plus torque required to align
Widt
hDia. Thru 34,93
Widt h
34,93
d nut with the shaft3,31/2,93
slotted
nut with the shaft
3,31/2,93
27,99/27,66
[1.375]
[1.375]
hole
crosshole
[.130/.115]
[.130/.115]
[1.102/1.089]
25,43/25,37
25,43/25,37
[1.001/.999]
[1.001/.999]
125,000,17mm
125,000,17mm
Taper Taper
Per Mete
Per Mete
r
r
4,06/3,81
4,06/3,81 [1.500.002
[1.500.002
inch Taper
inch Taper
Per FooPertFoo t
[.160/.150]
[.160/.150] Tapered
Tapered
Shaft End
ShaftPer
End
SAE
PerJ50
SAE J50
1
1
Dia. Thru
Dia. Thru ExceptExcept
as specified
as specified
2,93
3,31/2,93
/.115]
[.130/.115]
25,00/24,97
25,43/25,37
25,43/25,37
.984/.983
[1.001/.999]
[1.001/.999]
Dia.
125,000,17mm Taper Per Mete
125,000,17mm
r
Taper Per Mete r
[1.500.002 inch Taper Per Foo[1.500.002
t
inch Taper Per Foo t
Mou ntin
g ntinEnd
g Per SAE J50 1
Tapered Shaft End Per SAE J50
Tapered
1Mou
Shaft
Surface
Surface
Except as specified
Except
as* specified
*
38,6/37,0
38,6/37,0
[1.52/1.46]
[1.52/1.46]6,4 [.25]
6,4 [.25]
5,6/3,65,6/3,6
7/8 in. Dia. Straight
StraigStraig
ht ht
25,07/24,81
25,07/24,81
[.22/.14]
[.22/.14]
Key Key
Shaft with Key [.987/.977]
[.987/.977]
38,6/37,0
[1.52/1.46]
25,07/24,81
[.987/.977]
22,22/22,19
[.875/.874]
Dia.
B-2
25mm Dia. Straight Shaft
with 8mm Keyway
Mou ntin g
Surface *
Mou ntin g
Surface *
38,6/37,0
6,4 [.25] [1.52/1.46]
5,6/3,6 6,4 [.25]
Straig
ht
25,07/24,81
[.22/.14]Straig ht
22,22/22,19
22,22/22,19
Key[.987/.977]
Key
[.875/.874]
[.875/.874]
Dia. Dia.
22,22/22,19
[.875/.874]
Dia.
38,6/37,0
[1.52/1.46]
5,6/3,6
[.22/.14]
B-3
B-4
Mou ntin
Moug ntin g
Surface
Surface
*
*
50,6/49/,0
50,6/49/,0
[1.99/1.93]
[1.99/1.93]
8x8 8x8
x 30mm
x 30mm
StraigStraig
ht ht
KeyMou
Keyntin g
Surface *
7,4/5,47,4/5,4
[.29/.21]
[.29/.21]
27,99/27,66
27,99/27,66
Mou
ntin[1.102/1.089]
g
[1.102/1.089]
Surface *
50,6/49/,0
[1.99/1.93]
7,4/5,4
7,4/5,4
8x8
[.29/.21] 8 x 8
[.29/.21]
x 30mm
x 30mm
Straig ht
Straig ht
27,99/27,66
25,00/24,97
25,00/24,97 Key
Key [1.102/1.089]
.984/.983
.984/.983
Dia. Dia.
M8 x 1,25
M8 x-6H
1,25x -6H x
16,0 [.63]
16,0 Deep
[.63] Deep
25,00/24,97
.984/.983
Dia.
M8 x 1,25 -6H x
M8 x 1,25 -6H x
16,0 [.63] Deep
16,0 [.63] Deep
Mou ntin
Moug ntin g
Surface
Surface
*
*
38,6/37,0
38,6/37,0
[1.52/1.46]
[1.52/1.46]
5,6/3,65,6/3,6
7/8 in. Dia. SAE B Shaft
[.22/.14]
[.22/.14]
13 T Spline d
Mou ntin g
Surface *
Mou ntin g
Surface *
38,6/37,0
[1.52/1.46]
5,6/3,6
21,79/21,66
21,79/21,66
[.22/.14]
[.858/.853]
[.858/.853]
MajorMajor
Dia. Dia.
21,79/21,66
[.858/.853]
Major Dia.
5,6/3,6
[.22/.14]
21,79/21,66
[.858/.853]
Major Dia.
* 2 Bolt SAE B mounting flange has a greater
pilot thickness and a thinner mounting plate (end
of shaft to flange, add 3,3 [.13]).
B-4-21
H, S and T Series
(101-, 103- 158-, 185-)
Note:
Mounting Surface Flatness
Requirement is ,13 mm
[.005 inch] Max.
Mounting Options
4 Bolt Magneto
Base Bock Mounting Kits
45
22 30'
15,2 [.60]
2,8 [.11]
Mounting
Surface
82,55/82,42
[3.250/3.245]
Pilot Dia.
133,9
[5.27]
Max.
106,35
[4.187]
Dia.
Bolt
Circle
13,87/13,46
[.550/.530] Dia. Thru
(2) Mounting Holes
104,4 [4.11] Max.
Base Block
Mounting Kits
2 Bolt SAE B
11,9 [.47]
6,1 [.24]
Mounting
Surface
101,60/101,47
[4.000/3.995
Pilot Dia.
146,05
[5.750]
Dia.
Bolt
Circle
No.123-1008 — 7/8-14 O-ring Port (2)
No.123-1007 — 1/2 NPTF Port (2)
19,05
[.75]
177,8
[7.00]
Max.
13,2
[.52]
124,0
[4.88]
Motor Mounting
Surface *
14,14/14,53
[.557/.572] Dia. Thru
(2) Mounting Holes
126,0 [496] Max.
10,4 [.41] Dia.
Mounting Holes (4)
50,8
[2.00]
9,4
[.37]
76,2
[3.00]
57,2
[2.25]
B-4-22
82,6
[3.25]
14,2
[.56]
101,6
[4.00]
*2 Bolt SAE B mounting flange has a
greater pilot thickness and a thinner
mounting plate.
Ports
H, S and T Series
(101-, 103-, 158-, 185-)
End Ports — H Series only
G 1/2 (BSP) (2) Port A Pressurized — CW
or 3/4-16 O-Ring (2)
Dimensions
Standard Rotation Viewed
from Drive End
Note:
Ports
End ported motor pressure
is derated. Reference page
B-2-2 for ratings.
End Ports (H Series only)
7/8-14 ports
44,7
[1.76]
Max.
19,1 [.75]
42,7
[1.64]
7/8-14 UNF
O-ring
Ports (2)
Side
Ports
H Series
S Series
T Series
Mounting
Surface *
Use of Teflon Tape Sealant/
Lubricant (with 1/2 14 NPTF
Port Connectors only).
B-4
47,8
[1.88]
22,9
[.90]
6-1/2 or 1/2 NPTF ports
42,7
[1.64]
Manifold Ports
Mounting
Surface *
Wrap
Use the following
procedures:
• Wrap approx. 1 1/2 Turns
of 13 mm [1/2 in.] wide
Teflon Tape around fitting
threads — start tape 2
threads up from end of
fitting.
B-3
23,9
[.94]
45,7
[1.80]
G 1/2 BSP
or
1/2-14 NPTF
(2)
When using fittings with
Teflon tape, be careful when
taping and tightening. Over
tightening or improperly
taped fittings can cause
damage to housing or
leakage.
B-2
45,7
[1.80]
28,4
[1.12]
42,7
[1.64]
Customer
Supplied
O-rings
(-112)
31,6
[1.25]
45,7
22,9
[1.80]
[.90]
22,9
[.90]
Manifold Ports w/manifold case port
42,7 [1.64]
14,2
[.56]
28,4 [1.12]
12,7 [.50]
14,2 [.56]
31,6 [1.25]
22,9 [.90]
• Tighten threads to a
Maximum of 34 Nm [25
lb-ft]. — Do Not Tighten
Further —
63,5
[2.50]
5/16-18 UNC (12,7 [.50] Max. Screw
Thread Engagement) (4)
or
M8 x 1,25 (12,7 [.50] Max. Screw
Note:
End ported motor option is
derated to 1400 continuous,
1700 psi intermittent.
• If fittings leak when tightened to maximum torque,
either retape, reseal, or
replace fittings.
7,87 [.31]
Optional Case Drain
45,7 [1.80]
Port Location
(T-Series Only) 5/16-18 UNC (12,7 [.50] Max. Screw
63,5 [2.50]
*2 Bolt SAE B mounting flange has a greater
or M8x1,25 (12,7 [.50] Max. Screw
pilot thickness and a thinner mounting plate.
B-4-23
Notes
B-4-24
W Series (162-)
Features:
• Heavy duty bearing
Highlights
Heavy Duty Bearing
Motor Shaft Drive
• Wheel drive interface
Geroler ® Star
• Three-pressure zone
design (ability to reduce
case pressure)
shafts, mounts and special options
customer needs
Benefits:
•High side-load capacity
•High shock load capability
•Wheel mount interface
•Compact powerful
package
•High efficiency
•Smooth low-speed
operation
Description
Char-Lynn W Series motors with the Geroler
displacement element offer the same low friction
and long-life advantages as the S and T Series.
The W Series features the simplicity of Eaton’s proven
spool valve and a Geroler element that provides superior
drive life and smooth performance. In addition, this motor
has a rugged housing with an extra large capacity side load
bearing.
Applications:
•Scissors lifts
•Boom lifts
•Mid-size ZTR mowers
•Turf equipment
•Greens mowers
•Sand trap rakes
W Series Motors
Geroler Element
Flow l/min [GPM]
B-5
•Extended leak-free
performance
7 Displacements
Speed 288 RPM
Pressure bar [PSI]
165 [2400] Cont.***
•Railroad maintenance
equipment
•Industrial sweepers and
floor polishers
•Skid steer attachments
• Many more
179 [2600] Inter.**
Torque Nm [lb-in] 410 [3624] Cont.***
562 [4970] Inter.**
Scissor Lift
Sweeper
Trencher
Boom Lift
B-5-1
W Series (162-)
Specifications
Retaining Ring
Washe r
Output Shaft/
Spool Valv e
Washe r,
Backup
Bearing,
Ball
Seal
Seal,
Pressure
Geroler
Housing
Seal
Socket Head Cap Screw
Drive
End Cap
Plug/Case Drain
View of Geroler Sectio n
Specification Data — W Series Motors
Displ. cm3/r [in3/r]
80
126
154
195
251
303
374
[4.9][7.7][9.4] [11.9] [15.3] [18.5][22.8]
Max. Speed (RPM)
267
288
214
200
200
200
200
Flow l/min [GPM]
Theo. Torque
Nm [lb-in]
Pressure
∆bar [∆PSI]
23 [6]
23 [6]
176 [1555]
189 [1676]
165 [2400]
179 [2600]
30 [8]
30 [8]
279 [2470]
298 [2640]
165 [2400]
179 [2600]
34 [9]
34 [9]
318 [2813]
373 [3301]
152 [2200]
179 [2600]
38 [10]
38 [10]
318 [2816]
439 [3882]
124 [1800]
179 [2600]
53 [14]
53 [14]
375 [3319]
548 [4849]
110 [1600]
165 [2400]
62 [16.5]
62 [16.5]
387 [3429]
539 [4769]
97 [1400]
138 [2000]
68 [18]
76 [20]
410 [3624]
562 [4970]
83 [1200]
124 [1800]
Continuous
Intermittent
Continuous
Intermittent
Continuous
Intermittent
Note:
Note:
Recommended Fluids:
load applications.
179 bar [2600 PSI]
The case must be flooded
when the motor is operating.
Δ Pressure:
type hydraulic oil with a
viscosity of not less than 70
SUS at operating temperature.
return port
Recommended System
Operating Temp.:
Do Not Exceed ∆ Pressure
Rating (for displacement size
see chart above).
Return Pressure
(Back-Pressure):
Do not exceed ∆ pressure
rating (see chart above).
Case drain required.
Note:
Optional version can be
used without case drain.
Continuous Rating:
-34°C to 82°C [-30°F to
180°F]
Motor may be run
10% of every minute
Case Pressure:
Minimum – No Pressure
Maximum – 103 bar [1500
PSI] without case drain.
B-5-2
per ISO Cleanliness Code,
level 20/18/13
W Series (162-)
80 cm3/r [4.9 in3/r]
Performance Data
[2]
Flow l/min
[GPM]
7,6
[4]
15,1
[6]
22,7
[600]
41
Continuous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2400] [2600]
124
138
165
179
110
55
69
83
97
152
[204]
23
93
[223]
25
178
[255]
29
267
[337]
38
89
[357]
40
172
[342]
39
265
[474]
54
88
[489]
55
170
[477]
54
262
[612]
69
84
[627]
71
168
[612]
69
258
[748]
85
83
[769]
87
165
[749]
85
257
[883] [1019] [1149] [1281] [1412] [1540] [1610]
115
130
145
174
182
100
160
73
69
69
56
39
79
61
[902] [1035] [1169] [1295] [1424] [1555] [1676]
117
132
146
176
189
102
161
157
154
146
131
117
159
142
[879] [1014] [1154] [1286] [1408] [1533] [1648]
99
115
130
145
173
186
159
252
248
241
235
219
206
229
126 cm3/r [7.7 in3/r]
Flow l/min [GPM]
Continuous
[400]
28
[2]
7,6
[4]
15,1
[6]
22,7
[8]
Intermittent
30,3
[400]
28
[600]
41
Continuous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2400] [2600]
110
55
69
83
97
179
124
138
152
165
[390]
44
58
[382]
43
113
[367]
41
172
[346]
39
228
[605]
68
56
[605]
68
106
[587]
66
167
[561]
63
225
[817] [1032]
92
117
55
51
[817] [1036]
92
117
106
104
[802] [1017]
91
115
164
161
[769] [981]
87
111
220
216
[1248]
141
49
[1252]
141
93
[1236]
140
156
[1203]
136
213
[1448]
164
45
[1463]
165
97
[1444]
163
152
[1419]
160
208
[1656]
187
43
[1694]
191
94
[1668]
188
147
[1634]
185
201
[1871]
211
41
[1908]
216
88
[1882]
213
141
[1849]
209
195
[2069]
234
33
[2113]
239
82
[2091]
236
134
[2039]
230
188
[2243]
253
32
[2306]
261
79
[2284]
258
130
[2217]
250
174
[2414]
273
26
[2470]
279
74
[2459]
278
120
[2432]
275
163
[2513]
284
17
[2640]
298
60
[2637]
298
103
[2633]
297
149
B-5
Flow l/min [GPM]
154 cm3/r [9.4 in3/r]
[2]
7,6
[4]
15,1
[6]
22,7
[8]
30,3
[9]
34
Continuous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2400] [2600]
110
179
55
69
83
97
152
124
138
165
[400]
28
[600]
41
[450]
51
47
[470]
53
94
[435]
49
143
[407]
46
190
[380]
43
214
[723] [989]
82
112
47
46
[737] [1009]
83
114
93
90
[715] [984]
81
111
140
138
[677] [945]
76
107
188
186
[648] [914]
73
103
212
210
[1249]
141
44
[1276]
144
89
[1252]
141
137
[1214]
137
184
[1183]
134
207
[1512]
171
40
[1540]
174
87
[1513]
171
134
[1477]
167
182
[1452]
164
206
[1769]
200
39
[1802]
204
84
[1787]
202
131
[1740]
197
179
[1714]
194
202
[2021]
228
36
[2064]
233
81
[2020]
228
128
[2005]
227
176
[1981]
224
200
[2269]
256
33
[2323]
262
78
[2274]
257
124
[2260]
255
171
[2243]
253
196
[2502]
283
30
[2570]
290
73
[2521]
285
117
[2503]
283
166
[2499]
282
191
[2714]
307
26
[2813]
318
67
[2812]
318
112
[2735]
309
158
[2733]
309
182
[2904]
328
19
[3019]
341
65
[3042]
344
103
[2964]
335
148
[2964]
335
173
[3019]
341
10
[3242]
366
52
[3301]
373
91
[3206]
362
137
[3195]
361
162
195 cm3/r [11.9 in3/r]
Flow l/min [GPM]
[2]
7,6
[4]
15,1
[6]
22,7
[8]
30,3
[10]
38
[400]
28
[600]
41
[478]
54
38
[515]
58
75
[524]
59
114
[518]
59
151
[462]
52
190
[827]
93
38
[872]
99
73
[878]
99
111
[856]
97
150
[797]
90
188
Continuous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2400] [2600]
179
138
110
165
55
69
83
97
152
124
[1171]
132
37
[1220]
138
73
[1214]
137
111
[1187]
134
150
[1133]
128
187
[1511]
171
36
[1558]
176
71
[1551]
175
110
[1524]
172
149
[1468]
166
186
[1839]
208
35
[1886]
213
70
[1875]
212
108
[1861]
210
147
[1799]
203
184
[2153]
243
34
[2206]
249
69
[2199]
248
106
[2187]
247
145
[2118]
239
184
[2452]
277
34
[2518]
284
66
[2518]
284
105
[2499]
282
144
[2442]
276
182
[2756]
311
30
[2816]
318
64
[2824]
319
103
[2782]
314
143
[2739]
309
179
[3027]
342
29
[3107]
351
62
[3113]
352
99
[3064]
346
141
[3023]
342
176
[3275] [3513] [3673]
397
415
370
22
16
26
[3382] [3647] [3882]
412
439
382
52
44
56
[3389] [3666]
414
383
91
95
[3334]
377
136
[3281]
371
160
[3673]
415
16
}
Torque [lb-in ]
Nm
Speed RPM
B-5-3
W Series (162-)
251 cm3/r [15.3 in3/r]
Performance Data
[2]
7,6
[4]
Flow l/min [GPM]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
53,0
[400]
28
[600]
41
[759]
86
30
[806]
91
59
[780]
88
90
[720]
81
120
[645]
73
148
[557]
63
178
[460]
52
208
[1194]
135
29
[1257]
142
58
[1219]
138
88
[1148]
130
118
[1080]
122
147
[992]
112
177
[888]
100
206
Continuous
[800] [1000] [1200] [1400] [1600] [1800] [2000] [2200] [2400]
124
140
152
110
55
69
83
97
165
[1683]
190
29
[1691]
191
58
[1646]
186
87
[1590]
180
117
[1513]
171
147
[1428]
161
176
[1330]
150
206
[2122]
240
28
[2130]
241
56
[2084]
235
86
[2029]
229
117
[1947]
220
145
[1864]
211
174
[1761]
199
203
[2535]
286
27
[2563]
290
55
[2515]
284
85
[2449]
277
114
[2371]
268
145
[2292]
259
174
[2191]
248
202
[2928]
331
27
[2988]
338
55
[2933]
331
83
[2861]
323
112
[2779]
314
143
[2697]
305
172
[2615]
295
200
[3319]
375
25
[3381]
382
52
[3336]
377
83
[3236]
366
111
[3151]
356
141
[3087]
349
169
[3035]
343
197
[3634] [3946] [4242] [4553]
411
446
479
514
22
17
15
14
[3799] [4147] [4515] [4849]
429
469
510
548
48
47
41
40
[3716]
420
79
[3627]
410
108
[3515]
397
137
303 cm3/r [18.5 in3/r]
Continuous
[2]
Intermittent
Flow l/min [GPM]
7,6
[4]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45
[14]
53
[16.5]
62
[400]
28
[600]
41
[920]
104
24
[960]
108
49
[911]
103
73
[843]
95
99
[752]
85
123
[652]
74
148
[526]
59
172
[353]
40
203
[1454]
164
24
[1487]
168
49
[1445]
163
73
[1375]
155
98
[1274]
144
122
[1170]
132
147
[1039]
117
172
[864]
98
203
Continuous
[800] [1000] [1200] [1400] [1600] [1800] [2000]
110
124
55
69
83
97
140
[2969]
335
22
[3006]
340
46
[2952]
334
71
[2886]
326
95
[2792]
316
119
[2691]
304
145
[2548]
288
169
[2369]
268
200
[3429]
387
22
[3457]
391
45
[3411]
385
69
[3350]
379
94
[3274]
370
119
[3123]
353
144
[2999]
339
168
[3859] [4230] [4583]
478
436
518
18
20
16
[3905] [4338] [4769]
441
490
539
44
41
39
[3842] [4276]
483
434
66
68
[3763]
425
93
[3650]
412
118
[800] [1000] [1200]
55
69
83
[1400]
97
[1600]
110
[1974]
223
24
[2007]
227
47
[1961]
222
72
[1888]
213
97
[1789]
202
122
[1691]
191
146
[1560]
176
171
[1367]
154
201
[2480]
280
23
[2513]
284
47
[2473]
279
72
[2393]
270
96
[2303]
260
120
[2199]
248
145
[2064]
233
170
[1876]
212
200
374 cm3/r [22.8 in3/r]
Continuous
[2]
Flow l/min [GPM]
7,6
[4]
15,1
[6]
22,7
[8]
30,3
[10]
37,9
[12]
45,4
[14]
53,0
[16]
60,6
[18]
68,1
[20]
75,7
B-5-4
[400]
28
[600]
41
[1086]
123
20
[1152]
130
39
[1099]
124
60
[1018]
115
80
[940]
106
100
[809]
91
120
[648]
73
141
[485]
55
160
[307]
35
180
[111]
13
201
[1753]
198
19
[1797]
203
39
[1749]
198
58
[1662]
188
79
[1582]
179
99
[1454]
164
119
[1284]
145
139
[1107]
125
159
[930]
105
179
[730]
82
199
[2365]
267
17
[2431]
275
38
[2377]
269
57
[2290]
259
78
[2210]
250
97
[2077]
235
117
[1907]
215
138
[1722]
195
157
[1543]
174
178
[1342]
152
198
[2960]
334
16
[3048]
344
36
[2996]
339
56
[2894]
327
76
[2812]
318
96
[2677]
302
116
[2506]
283
137
[2315]
262
157
[2133]
241
178
[1939]
219
197
[3533]
399
14
[3624]
409
34
[3557]
402
54
[3440]
389
75
[3346]
378
95
[3216]
363
115
[3033]
343
137
[2838]
321
157
[1800]
124
[4025] [4484] [4970]
507
562
455
12
11
12
[4129] [4599]
520
467
31
33
[4077]
461
53
[3952]
447
74
[3816]
431
95
[4583]
518
16
}
Torque [lb-in ]
Nm
Speed RPM
W Series (162-)
Ports
22,86
[.900]
Dimensions
45.72
[1.800]
7/8-14 SAE O-Ring Ports
G1/2 BSP Straight Thread Port
Manifold (15/16-18 Mounting Threads)
19,3/17,3 [.76/.68] (2)
43,18/42,67 [1.700/1.680]
90,75/90,25 [3.573/3.553]
63.50 [2.500]
2x 134,1 [5.28] Max.
5/16-18 UNC 2B 00 [.74] Min. Full Thread Depth or
M8 x 1,25 -6H 00 [.50] Min. Full Thread Depth
Manifold
Port B
87,45/86,94 [3.443/3.423]
127,4/126,1
[5.00/4.995]
Pilot Dia
82,55/82,42
[3.250/3.245]
Pilot Dia
B-5
147,62 [5.812] Bolt Circle
Port A
X
7,2/5,6 [.28/.22]
44,7/43,7 [1.76/1.72]
13,59 [.535]
Dia.l Thru (4)
7/16-20 UNF-2B O-ring Port, Size 4 or
G1/4 (BSP) Straight Thread Port
Case Drain
14,22
[.560]
Min.
49,78/49,28 [1.960/1.940]
65,74 [2.588]
Note:
Motors without check
valves that require a case
drain. Remove O-Ring
plug, connect drain line to
reservoir. Include a relief
valve (in the drain line) set
to maintain 3,4 bar [50 PSI]
motor case pressure.
14,30 [.563]
28,57 [1.125]
Y
10,11 [.398]
W Series Dimensions
1-1/4 Tapere d
36,19
[1.425]
DisplacementX
mm [inch]
cm3/r [in3/r]
Y
mm [inch]
80 [4.9]
126 [7.7]
154 [9.4]
195 [11.9]
251 [15.3]
303 [18.5]
374 [22.8]
116,6 [4.59]
119,6 [4.71]
122,2 [4.81]
126,2 [4.97]
131,6 [5.18]
136,4 [5.37]
143,3 [5.64]
9,1 [.36]
11,9 [.47]
14,7 [.58]
18,5 [.73]
23,9 [.94]
29,0 [1.14]
35,6 [1.40]
B-5-5
W Series (162-)
Recommended Torque:
(373 Nm [275 lb-ft] Dry)
(305 Nm [225 lb-ft] Lub) Plus
Torque required to align the
slotted nut with the Shaft
Crosshole.
Dimensions Shafts
1 1/4 Tapered
108,5 [4.27] Max.
Mounting
Surface
4 Bolt Mount
22,9/21,6
[.90/.95]
12,7 [.50]
Position 7-8
1-20 UNEF
Mounting
Surface
7,963/7,937
[.3135/.3125]
Square Key
4,1 [.16]
Dia. Thru
31,7 [1.250] Dia.
54,6/53,6 [2.15/2.11]
3,97/3,63 [.156/.143]
SAE J501 Standard Tapered Shaft
125,00 0,17 Taper per Meter
[1.500 .002 Taper per Foot
54,9 [2.16] Max.
Hub
768 [6800]
Max. Torque
Nm [lb-in]
36,6 [1.44] Across Flats
1 1/4 Inch Straight
96,8 [3.81] Max.
Mounting
Surface
38,1 [1.50]
Position 7-8
4 Bolt Mount
Mounting
Surface
7,963/7,937
[.3135/.3125]
35,34/35,05
[1.391/1.380]
32,6/30,9 [1.28/1.22]
768 [6800]
Max. Torque
Nm [lb-in]
3/8-16 UNC x
19,6 [.77] Deep Min.
31,75/31,69 [1.250/1.248] Dia.
47,3 [1.86]
Max. Coupling
32 mm Straight
107,2 [4.22] Max.
Position 7-8
4 Bolt Mount
Mounting
Surface
Mounting
Surface
10,00/9,96
[.394/.392]
35,0/34,7
[1.38/1.37]
M8 x
1.25 -6H x
21,6 [.85]
Deep Min.
9,2/4,5 [.36/.18]
45,00 [1.772]
768 [6800]
Max. Torque
Nm [lb-in]
32,017/31,991
[1.2605/1.2595]
56,4 [2.22]
Max. Coupling
1 1/4 14 Tooth Splined
93,2 [3.67] Max.
Mounting
Surface
Position 7-8
4 Bolt Mount
Mounting
Surface
Flat Root Side Fit,
14 Tooth
12/24 Spline
to Fit ANSI
B92.1 1976
3/8-16 UNC
19,0 [.75] Min. Depth
31,75/31,06
[1.250/1.223] Dia.
B-5-6
45,5 [1.79] Max.
Coupling
33,0 [1.30]
Min. Full
Spline Depth
768 [6800]
Max. Torque
Nm [lb-in]
W Series (162-)
-40
160
180
1.75
1.50
Load Adjustment factor (SL)
1) C
ase pressure needs to
be added to the outward
axial thrust load and
subtracted from inward
axial thrustload – Case
Pressure bar x 87, 1 [PSI x
1.35]
2) Life values in Chart A can
be adjusted for speeds up
to 200 rpm.
Life value x 100 rpm
application rpm
Chart B — Load Adjustment factor
Distance from Front of Flange (mm)
-20
0
20
40
60
80 100 120 140
1.25
1.00
0.75
0.50
0.25
0.00
[-2]
are
3) Shaded areas
intermittent loading.
4) To convert application radial load at any load location
to sideload at the center
of keyway multiply load by
the application factor from
Chart B.
[-1]
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Distance from Front of Flange ([inch])
(Centerline of Keyway 1-1/4 Tapered Shaft )
B-5
70,1 [2.76]
Example:
Side Load: 4849 N @ 120 mm [1090 lbf @
4.75 inch] from flange.
Average Thrust Load: 890 N [200 lbf]
inward (toward motor).
Case Pressure: 66 bar [960 PSI].
Average Speed: 150 rpm.
Expected Life Calculation: Adjust side load
value (due to load variation): from Chart B
look at 120mm [4.75 inch] read at angled
curve for load adjustment factor of 1.38.
Adjusted load is: (4849 N [1090 lbf]) x (1.38)
= 6690 N [1504 lbf]
Thrust Load Value (due to case pressure):
(960 PSI) x (1.35) = [1296 lbf]
(66 bar) x (87,1) = 5750 N
Average thrust load found to be 890 N
[200 lbf] inwards so subtract from thrust
load due from case pressure:
5750 N - 890 N = 4860 N or
[1296 lbf] - 200 lbf = [1096 lbf]
Read Life Expectancy from Chart A: Value
from chart reading across top to 6672 [1500]
(6090 N [1504 lbf]) and down left side to
4895 [1100] (4875 N [1096 lbf])
Life = 1800 Hours
Speed Adjustment for over 100 rpm:
(1800 hrs) x (100 rpm) = 1200 Hours
150 rpm
Chart A — Expected B10 Life (hours) of Bearing Under Various Loads
Axial Thrust
Radial Load at Centerline of keyway at 100 RPM
1110
N
lbf]
[250]
445
[100]
410 600
1335
[300]
92 700
2225
[500]
39 400
3115
[700]
21 400
4005
[900]
13 300
4895
[1100] 9 000
5785
[1300] 6 500
6670
[1500] 4 800
7560
[1700] 3 700
8450
[1900] 3 000
8895
[2000] Max. Thrust
2225 33354450 4560 66707785889511120 N
13345 N
[500] [750] [1000] [1250] [1500][1750][2000][2500lbf]
[3000lbf)
66 000 19 600 8 300 4 200 2 400 1 500 1 000 530
310
40 900 19 600 8 300 4 200 2 400 1 500 1 000 530
310
20 900 12 400 7 900 4 200 2 400 1 500 1 000 530
310
12 600 8 100 5 500 3 900 2 400 1 500 1 000 530
8 400 5 700 4 000 2 900 2 200 1 500 1 000 530
6 000 4 200 3 100 2 300 1 800 1 400 1 000
4 500 3 200 2 400 1 900 1 500 1 200 900
3 500 2 600 2 000 1 500 1 200 1 000
2 800 2 100 1 600 1 300
2 200
B-5-7
W Series (162-)
to identify all of the configuration options for the W Series
motor. Use this model code to specify a motor with the
desired features. All 16-digits of the code must be present
when ordering. You may want to photocopy the matrix
below to ensure that each number is entered in the
correct box.
Model Code
M
1 Product
M – Motor
2 , 3 Series
0W – W Series
4 , 5 Displacement
cm3/r [in3/r]
05 – 30 [4.9]
08 – 126 [7.7]
09 – 154 [9.4]
12 – 195 [11.9]
15 – 251 [15.3]
19 – 303 [18.5]
23 – 374 [22.8]
6 Mounting Type
B – 4 Bolt (Wheel) 82,6
[3.25] Pilot Dia. and 13,59
[.535] Dia. Mounting Holes
147,6 [5.81] Dia., B.C., 127,0
127,0 [5.00] rear pilot
B-5-8
0 W
* *
*
* *
*
*
* *
*
*
0
D
2 3
4 5
6
7 8
9
10
11 12
13
14
15
16
7 , 8 Output Shaft
02 –1 1/4 inch Dia. Flat Root
Side Fit, 14 Tooth, 12/24
DP
30° Involute Spline
with 3/8-16 UNC-2B Thread
in End, 33,0 [1.30] Min. Full
Spline
9 Ports
A – 7/8 -14 UNF - 2B SAE
O-Ring Port
B – G 1/2 (BSP) Straight
Thread Port
13 Special Features
(Assembly)
0 – None
14 Paint/Special
Packaging
03 – 1 1/4 inch Dia. .125:1
Tapered Shaft Per SAE
J501 with 1– 20 UNEF -2A
Threaded Shaft End and
Slotted Hex Nut, 7,938
[.3125] Square x 22,22 [.875]
Straight Key
A – 7/16 - 20 UNF - 2B SAE
O-Ring Port
C – Internal Check Valve
15 Eaton Assigned
04 – 32mm Dia. Straight
Shaft with M8 x 1, 25-6H
Thread in End, 9,982 [.3930]
Wide x 7,995 [.3132] High x
45,00 [1.772] Long Key
(Hardware)
0 – Assigned Code
Thread Port
00 – None
01 – Viton Seals
06 – 1 1/4 inch Dia. Straight
Shaft with 3/8 – 16 UNC 2B
Thread in End, 7.938 [.3125]
Square x 34,92 [1.375]
Straight Key
0 – No Paint, Individual Box
A – Low Gloss Black Primer,
Bulk Box Option
16 Eaton Assigned
Design Code
D – Assigned Design Code
W Series with
Parking Brake
(162-)
Ports
23,4/22,4
[.92/.88]
7/8
-14 UNF 2B SAE O-Ring Ports (2) or
G 1/2 (BSP) Straight Thread
46,7/44,7
[1.84/1.76]
Dimensions
19,3/17,3[.76/.68] (2)
Port Dimensions
82,55/82,42 7/8-14 UNF 2B O-ring Ports (2)
[3.250/3.245] G 1/2 (BSP) Straight Thread
Port B
Pilot Dia.
2x 134,1 [5.28] Max.
127.0/126,9
[5.00/4.995]
Pilot Dia.
15,0/14,0
[.59/.55]
B-5
147,62 [5.812] Bolt Circle
7,2/5,6 [.28/.22]
Port A
16.3/13.9
[.65/.55]
44,7/43,7 [1.76/1.72]
13,59 [.535] Dia.l Thru (4)
37.1/36,5 [1.46/1.44]
X
G 1/4 (BSP) Straight Thread Port
Brake Release Port
Y
Z
Mounting Dimensions
66,0/64,0
[2.60/2.52]
(2)
1-1/4 Tapere d
G 1/4 (BSP) Straight Thread Port–
Manual Brake Release Access Port.
Tighten plug to manually release brake.
PORTING AND MOUNTING DIMENSIONS
Displacement
X Y Z
cm3/r [in3/r]
mm [inch]
mm [inch]
mm [inch]
80 [4.9] 9,1 [0.36]
119,9 [4.72]
198,4 [7.81]
126 [7.7]
11,9 [0.47]
122,9 [4.84]
201,2 [7.92]
154 [9.4]
14.7 [0.58]
125,5 [4.94]
204,0 [8.03]
195 [11.9]18,5 [0.73]
129,6 [5.10]
207,8 [8.18]
251 [15.3]23,9 [0.94]
134,9 [5.31]
213,4 [8.40]
303 [18.5]29,0 [1.14]
139,7 [5.50]
217,7 [8.59]
374 [22.8]35,6 [1.40]
146,6 [5.77]
226,8 [8.85]
Specifications
Brake Release Pressure
205 bar [3000 PSI] Max.; 15 bar [250 PSI] Min.
B-5-9
W Series,
162 plus four digit number
product number —
Example 162-1153.
Product Numbers
Standard
Shaft Displ. cm3/ r [in3/ r] / Product Number
80 [4.9]
126 [7.7]
154 [9.4]
195 [11.9]
251 [15.3]
303 [18.5]
374 [22.8]
Standard
162-1016
-1017-1018-1019-1020-1021-1022
w/Case Drain
162-1023
-1024-1025-1009-1008-1026-1027
162-1009
W Series with Parking Brake
Shaft Displ. cm3/ r [in3/ r] / Product Number
80 [4.9]
126 [7.7]
154 [9.4]
195 [11.9]
251 [15.3]
303 [18.5]
374 [22.8]
Standard
162-1143
-1144-1145-1146-1183-1148-1149
162-1146
Note:
All above motors have
1-1/4 inch tapered output
shaft, 7/8 inch O-Ring Ports,
internal check valves.
For W Series Motors with
a configuration not shown
in the chart above: Use the
model code number system
to specify the product in
detail. (see page B-5-8
and use the model code
supplement shown on page
B-5-11 for spring-applied
hydraulic-release parking
brake).
B-5-10
Model Code
M
0 W
* *
*
* *
*
*
* *
*
*
0
1
2 3
4 5
6
7 8
9
10
11 12
13
14
15 16
1 Product
M – Motor
2 , 3 Series
0W – W Series with Parking
Brake
4 , 5 Displacement
cm3/r [in3/r]
05 – 30 [4.9]
08 – 126 [7.7]
09 – 154 [9.4]
12 – 195 [11.9]
15 – 251 [15.3]
19 – 303 [18.5]
23 – 374 [22.8]
6 Mounting Type
B – 4 Bolt (Wheel) 82,6
[3.25] Pilot Dia. and 13,59
[.535] Dia. Mounting Holes
147,6 [5.81] Dia., B.C., 127,0
127,0 [5.00] rear pilot
to identify all of the configuration options for the W motor.
7 , 8 Output Shaft
02 –1 1/4 inch Dia. Flat Root
Side Fit, 14 Tooth, 12/24
DP
30° Involute Spline
with 3/8-16 UNC-2B Thread
in End, 33,0 [1.30] Min. Full
Spline
9 Ports
A–
-14 UNF - 2B SAE
O-Ring Port
7/8
Thread Port
D
Features
13 Special
(Assembly)
0 – None
03 – 1 1/4 inch Dia. .125:1
Tapered Shaft Per SAE
J501 with 1– 20 UNEF -2A
Threaded Shaft End and
Slotted Hex Nut, 7,938
[.3125] Square x 22,22 [.875]
Straight Key
14 Paint/Special
Packaging
A – 7/16 - 20 UNF - 2B SAE
O-Ring Port
0 – No Paint, Individual
Box
Thread Port
- Individual Box
04 – 32mm Dia. Straight
Shaft with M8 x 1, 25-6H
Thread in End, 9,982 [.3930]
Wide x 7,995 [.3132] High x
45,00 [1.772] Long Key
Features
11 , 12 Special
(Hardware)
06 – 1 1/4 inch Dia. Straight
Shaft with 3/8 – 16 UNC 2B
Thread in End, 7.938 [.3125]
Square x 34,92 [1.375]
Straight Key
C – Internal Check Valve
00 – None
Assigned
15 Eaton
0 – Assigned Code
01 – Viton Seals
Assigned
16 Eaton
Design Code
11 – Spring-applied hydraulicrelease brake
D – Assigned Design Code
B-5-11
B-5

Eaton® Char-Lynn® Spool Valve Hydraulic Motors

Transcription

Similar documents

standard of excellence enhanced comprehensive band

Eaton® Char-Lynn® VIS (Valve-In

2nd Edition FiberGuide® Fibre Management Systems