Complete Product Brochure

INSTALLATION SYSTEMS FOR
FLOORING PROFESSIONALS
High-quality products • Progressive ideas • Great service
ADVANCEMENT
THROUGH
INNOVATION
Chembond holds to this fundamental
philosophy to meet the demands of the
flooring industry, both now and into the
future. Along with product development, this
innovation applies to everything we do – from
technical support to customer service and
communication. Since 1977, Chembond has
served as a pillar of the Canadian flooringinstallation industry by offering innovative,
dependable,
user-friendly
installation
products at affordable prices.
Beginning operations in Toronto, Chembond
has taken product performance, breadth of
offerings and branding to new levels while
offering the industry top-notch value and
customer support.
Continuing on its path of continual
improvement, Chembond will further this
trend of innovation by advancing the products
and technology needed to install the tile and
stone of tomorrow.
TABLE OF CONTENTS
SURFACE PREPARATION
2
Chempatch ™ 2101
WALL-BASE ADHESIVE
2
BaseBond ™ 1651
TILE AND STONE INSTALLATION MORTARS
3
ScratchBond ™ 8200
3
FloorBond ™ 8400
3
MagniFlex ™ 8810
4
MagniFlex Super 8820
4
MagniFlex Ultimate 8830
5
MagniFlex QS 8860
ADDITIVE
5
Chemlastic ™ 7400
CERAMIC TILE ADHESIVE
6
TileGrab ™ I 1640
SURFACE PREPARATION
WALL-BASE ADHESIVE
Chempatch™ 2101
BaseBond ™ 1651
Rapid-Set Cement Patch
Supreme Wall-Base Adhesive
Chempatch 2101 is a rapid-setting, polymer-modified, cementbased floor-patching compound. When mixed with water, it can
smooth, level and patch imperfections in concrete and approved
wood underlayments prior to floor-covering installation.
BaseBond 1651 is a premium acrylic-based adhesive for the
installation of most types of wall bases.
Features
• The ultimate floor preparation product for performance and
versatility
• Dries fast to an ultra smooth finish
• Self-cures to a compressive strength greater than
27,6 MPa (4,000 psi)
Technical Information
Pot life*
Up to 10 minutes
Final set†
Up to 40 minutes
Drying time before installing
floor covering
Features
• BaseBond 1651 is part of the EcoTech family of adhesives,
which are solvent-free, low-TVOC, low-odour and
nonflammable for safer installation.
• Will not stain wall base
• Great initial grab and long-term bond strength
• Thick viscosity for excellent trowelability
Uses
• For interior installation of vinyl, rubber and carpet types of wall
bases
60 to 90 minutes
Technical Information
Open time †
Approximate Coverage (per 10-kg [22-lb.] bag)
3 mm (1/8") thickness
2,60 m² (28 ft.²)
Packaging
Bag,10 kg (22 lbs.)
†
Packaging
Cartridge, 850 mL
Product Code 210122010
* Pot life may vary due to amount of material mixed, temperature
of substrate, room and water used in the mix. For more
information, see individual Product Data Sheet and Chembond’s
“Substrate Requirements for Floor Coverings” document. The
most recent information can be found at www.chembond.com.
Up to 30 minutes
(28.7 U. S. oz.)
Bucket, 9,46 L
(2.5 U.S. gals.)
Product Code 165172010
Product Code 165160020
Standard Trowel and Approximate Coverage
based on 3,79 L (1 U.S. gal.)
Set time shown is based on 23°C (73°F) at 50% relative
humidity. Actual times may vary depending on the size, ambient
and substrate temperatures, and humidity levels.
Flooring Type
Wall base
†
Standard Trowel
Size
3 x 3 mm
(1/8" x 1/8"),
saw-tooth
Coverage
85 linear m
(280 linear ft.)
Open time may vary due to substrate porosity, humidity levels
and amount of adhesive applied. For more information, see
individual Product Data Sheets and Chembond’s “Substrate
Requirements for Floor Coverings” document. The most recent
information can be found at www.chembond.com.
2
TILE AND STONE INSTALLATION MORTARS
ScratchBond ™ 8200
Scratchcoat Mortar for Metal
Lath
ScratchBond 8200 is a Portland-cement-based
scratchcoat mortar for use with metal lath on
plywood subfloors and countertops prior to
setting ceramic tile and stone. Use it with metal
lath fastened to exterior-grade plywood to
create a “semi-floating” underlayment system,
reducing the potential for in-plane cracking of
installed ceramic or stone.
Features
• Economical
• Portland-cement-based
• Mix with water only.
Uses
• Apply to metal lath that is attached to
exterior-grade plywood. Doing so creates
a “semi-floating” underlayment system that
reduces the potential for in-plane cracking
of installed ceramic tile or stone.
• Install ceramic tile later over the installation
of metal lath and ScratchBond 8200.
• For residential and commercial interior
floors and countertops
• Approved substrate:
– Exterior-grade plywood (on interior
residential floors and countertops only)
Technical Information
Pot life*
About 2-1/2 hours
Initial set (before
applying tile
mortar)
24 hours
Colour
Grey
†
Packaging
FloorBond ™ 8400
MagniFlex ™ 8810
FloorBond 8400 is a single-component,
Portland-cement mortar for installing lowabsorption ceramic floor tile, quarry tile and
pavers.
MagniFlex 8810 is a single-component,
polymer-modified, dry-set mortar for installing
vitreous (low-absorption) porcelain, ceramic,
paver and quarry tiles as well as traditional
nonvitreous tiles.
Dry-Set Floor Tile Mortar
Features
• An economical, floor tile mortar
• Portland-cement-based
• Mix with water (or undiluted Chemlastic™
7400 for increased performance).
Uses
• For residential interior/exterior floors and
commercial interior countertops
• Approved substrates (when mixed with
water):
– Interior residential concrete floors,
concrete mortars and concrete leveling
coats
• Approved substrates (when mixed with
undiluted Chemlastic 7400):
– Interior/exterior residential concrete
floors, concrete mortars and concrete
leveling coats
– Exterior residential floor tile installation
on concrete floors
– For setting vitreous and impervious
floor tiles on interior cement backer units
(CBUs) or interior/exterior concrete
– Exterior-grade plywood installed
on interior floors and countertops in
residential, dry areas only
Product Code
(50 lbs.)
820050010
Features
• Dry-set mortar
• Mix with water only.
Uses
• For residential/commercial interior floors,
walls and countertops
• Approved substrates:
– Interior residential and commercial
concrete floors, as well as walls and
countertops made of cement backer units
(CBUs), in dry areas
Technical Information
Pot life*
Pot life*
15 to 30 minutes
Initial set (before
grouting)
48 hours after
installation
Final set† (before
general foot
traffic)
72 hours after
installation
Colour
Grey
Product Code
(50 lbs.)
840050010
Meets or exceeds ANSI A118.1 standards
when mixed with water and ANSI A118.4
standards when mixed with undiluted
Chemlastic 7400
Initial set
(before grouting)
16 to 24 hours
Final set†
(before general
foot traffic)
24 to 36 hours after
installation
Colour
Grey
Bag, 22,7 kg
Product Code
(50 lbs.)
881050010
Meets ANSI A118.1 standards when mixed
with water
Standard Trowels and Approximate
Coverage
based on 22,7 kg (50 lbs.)
Standard
Trowel Size
Coverage
FloorBond
8400
6 x 6 x 6 mm
(1/4” x 1/4” x
1/4”), squarenotch
6,97 to 8,36
m² (75 to 90
ft.²)
Magniflex
8810
6 x 6 x 6 mm
(1/4” x 1/4” x
1/4”), squarenotch
6,97 to 8,36
m² (75 to 90
ft.²)
Product
Packaging
Bag, 22,7 kg
15 minutes
Packaging
About 4 hours
Open time*
About 4 hours
Open time*
†
Technical Information
†
Bag, 22,7 kg
Floor and Wall Tile Mortar
* P ot life and open time may vary due to amount of material mixed,
as well as temperature of substrate, room and water used in the
mix.
†
et times shown are based on 23°C (73°F) at 50% relative
S
humidity. Actual times may vary depending on the size, ambient
and substrate temperatures, and humidity levels. For more
information, see individual Product Data Sheets and Chembond’s
“Substrate Requirements for Tile” document. The most recent
information can be found at www.chembond.com.
3
TILE AND STONE INSTALLATION MORTARS
MagniFlex ™ Super 8820
Polymer-Modified Floor and Wall Tile Mortar
MagniFlex Super 8820 is an economical polymer-modified dry-set
mortar for setting tile and stone.
Features
• Excellent bond capacity
• For setting dimensional stone as well as ceramic, porcelain and
quarry tile
• Mix with water only.
Uses
• For residential (interior floors, countertops and walls; and exterior
floors and walls) and commercial (interior floors and walls; and
exterior floors)
• Approved substrates:
– Fully cured concrete, concrete mortars and concrete leveling
coats
– Masonry block
– Exterior-grade plywood (interior floors only)
– Gypsum wallboard (interior walls only)
– Cement backer units (CBUs), interior applications only
– Properly prepared unglazed tile, cement terrazzo, vinyl
composition tile (VCT), vinyl asbestos tile (VAT) and cutback
adhesive residue
MagniFlex ™ Ultimate 8830
High-Performance, Polymer-Modified Floor and
Wall Tile Mortar
MagniFlex Ultimate 8830 is a high-performance, polymer-modified,
single-component, thin-set mortar for setting ceramic tile and dimension
stone.
Features
• Enhanced and polymer-modified
• For setting dimensional stone as well as ceramic, porcelain and
quarry tile
• Mix with water only.
Pot life*
About 1-1/2 to 2 hours
Uses
• For setting floor and wall tile
• For residential (interior floors, countertops and walls; and exterior
floors and walls) and commercial (interior floors and walls; and
exterior floors)
• Approved substrates:
– F ully cured concrete, concrete mortars and concrete leveling
coats
– Masonry block
– Exterior-grade plywood (interior floors only)
– Gypsum wallboard (interior walls only)
– Cement backer units (CBUs), interior applications only
– Interior properly prepared unglazed tile, cement terrazzo, vinyl
composition tile (VCT), vinyl asbestos tile (VAT) and cutback
adhesive residue
Initial set† (before grouting)
16 to 24 hours
Technical Information
Technical Information
Final set† (before general foot
traffic)
Colours
Pot life*
72 hours after installation
About 2 hours
Initial set (before grouting)
†
Grey; white
Final set (before general foot
traffic)
Packaging
Bag, 22,7 kg (50 lbs.), grey
Product Code 882050010
Bag, 22,7 kg (50 lbs.), white
Product Code 882050012
16 to 24 hours
†
Colour
72 hours after installation
Grey
Packaging
Bag, 22,7 kg (50 lbs.), grey
Meets or exceeds ANSI A118.4 and ANSI A118.11 standards
Product Code 883050010
Meets or exceeds ANSI A118.4 and ANSI A118.11 standards
Standard Trowels and Approximate Coverage
based on 22,7 kg (50 lbs.)
Product
Standard Trowel
Size
Coverage
6 x 6 x 6 mm (1/4" x
1/4" x 1/4"), square
6,97 to 8,36 m²
(75 to 90 ft.²)
Magniflex Ultimate 6 x 6 x 6 mm (1/4" x
8830
1/4" x 1/4"), square
6,97 to 8,36 m²
(75 to 90 ft.²)
MagniFlex Super
8820
* P ot life may vary due to amount of material mixed, as well as temperature of substrate, room and
water used in the mix.
†
et times shown are based on 23°C (73°F) at 50% relative humidity. Actual times may vary
S
depending on the size, ambient and substrate temperatures, and humidity levels. For more information,
see individual Product Data Sheets and Chembond’s “Substrate Requirements for Tile” document. The
most recent information can be found at www.chembond.com.
4
TILE AND STONE INSTALLATION
MORTARS
ADDITIVE
MagniFlex ™ QS 8860
Chemlastic™ 7400
High-Performance, Polymer-Modified, Quick-Set
Floor and Wall Tile Mortar
MagniFlex QS 8860 is a single-component, high-performance,
polymer-modified quick-set mortar for installing ceramic tile and
dimensional stone.
Features
• Quick-set
• Polymer-modified
• Mix with water only.
Uses
• For fast tiling of floors and walls that must be ready for use in a
short time (such as in supermarkets, hospitals, airports and shopping
malls)
• For installing vitreous, semivitreous and nonvitreous ceramic tile and
impervious ceramic mosaics on residential interior floors, walls and
countertops; residential exterior floors and walls; and commercial
interior floors and walls
• For residential (interior floors, countertops and walls; and exterior
floors and walls) and commercial (interior floors and walls; and
exterior floors)
• Approved substrates:
– Fully cured concrete
– Concrete block and masonry block
– Exterior-grade plywood (interior floors and countertops only)
– Cement backer units (interior applications only)
– Interior properly prepared unglazed tile, old cement terrazzo
floors, vinyl composition tile (VCT), vinyl asbestos tile (VAT),
cutback adhesive residue, plastic laminate countertops and
noncushioned sheet vinyl
Technical Information
Pot life*
About 70 minutes
Final set
(before general foot traffic)
About 90 minutes
Colour
Grey
†
Chemlastic 7400 is an acrylic latex additive that forms high-strength
bonds to ceramic tiles when mixed with factory-prepared dry-set
mortars such as FloorBond ™ 8400.
Features
• Develops high-strength bond between tile and substrate
• Improves freeze/thaw resistance between tile and substrate
• M
ix only with factory-prepared dry-set mortars.
Uses when mixed undiluted with FloorBond 8400
• F or residential interior/exterior floor and countertops in dry areas
only
• F or installing ceramic, porcelain, mosaic, glass and quarry tiles;
pavers; slate; marble; and granite
• A
pproved substrates:
– Fully cured concrete (at least 28 days old)
– Cement backer units (CBUs) (interior only)
– Concrete mortars and concrete leveling coats
– Masonry block (floors only)
Technical Information when mixed with FloorBond 8400
Pot life*
About 4 hours
Initial set (before grouting)
48 hours
Final set
(before general foot traffic)
72 hours after installation
Colour
White
†
†
Packaging
Pail, 7,57 L (2 U.S. gals.), white
Product Code 740057010
Meets or exceeds ANSI A118.4 standards when mixed with
FloorBond 8400
About 30 minutes
Initial set† (before grouting)
Latex Additive for Dry-Set Mortar
Packaging
Bag, 22,7 kg (50 lbs.), grey
Product Code 886050010
Meets or exceeds ANSI A118.4 and ANSI A118.11 standards
Standard Trowels and Approximate Coverage
based on 22,7 kg (50 lbs.)
Product
MagniFlex QS
8860
Standard Trowel
Size
6 x 6 x 6 mm
(1/4" x 1/4" x 1/4"),
square
Coverage
6,50 to 8,36 m²
(70 to 90 ft.²)
* P ot life may vary due to amount of material mixed, as well as temperature of substrate, room and
water used in the mix.
†
Set times shown are based on 23°C (73°F) at 50% relative humidity. Actual times may vary
depending on the size, ambient and substrate temperatures, and humidity levels. For more information,
see individual Product Data Sheets and Chembond’s “Substrate Requirements for Tile” document. The
most recent information can be found at www.chembond.com.
5
CERAMIC TILE ADHESIVE
TileGrab™ I 1640
Type 1 Floor and Wall Tile Adhesive
TileGrab I 1640 is a Type 1, high-performance, multipurpose,
nonflammable, ceramic floor and wall tile adhesive. It is used
for installing ceramic, porcelain, mosaic and quarry tiles.
Features
• Ready to use (no mixing required)
• Easy to spread
• Quick-grab, nonslip
• Minimal odour
• Water cleanup
Uses
• For residential interior floors, walls and countertops in light-duty
applications
• For residential interior wet walls (shower; tub and bath surrounds)
where service requirements do not exceed ANSI A136.1 standards
• Approved interior substrates:
– Gypsum wallboard (walls only)
– Fully cured concrete walls (at least 28 days old)
– Masonry block walls
– Cement backer units (CBUs)
– APA or COFI Group 1 exterior-grade plywood (residential
floors and countertops in dry areas)
Technical Information
Open time
About 40 to 55 minutes
Initial set† (before grouting)
24 to 48 hours
Final set†
(before general foot traffic)
72 hours after installation
Colour
White
Packaging
Pail, 3,79 L (1 U.S. gal.), white
Product Code 164053020
Pail, 13,2 L (3.5 U.S. gals.), white
Product Code 164063020
Pail, 18,9 L (5 U.S. gals.), white
Product Code 164068020
Standard Trowel and Approximate Coverage
based on 3,79 L (1 U.S. gal.)
Product
TileGrab I 1640
†
Standard Trowel
Size
6 x 6 x 6 mm
(1/4" x 1/4" x 1/4"),
square
Coverage
2,32 to 3,44 m²
(25 to 37 ft.²)
Set times shown are based on 23°C (73°F) at 50% relative
humidity. Actual times may vary depending on the size, ambient and
substrate temperatures, and humidity levels. For more information,
see individual Product Data Sheets and Chembond’s “Substrate
Requirements for Tile” document. The most recent information can be
found at www.chembond.com.
6
CHEMBOND®
A Division of MAPEI® Inc.
2130 Williams Parkway
Brampton, Ontario L6S 5X7
Phone: 1-888-243-6263
Edition date: January 19, 2016
PR: 7674 MKT: 15-2105