User Manual
Transcription
User Manual
User Manual Nu-LB-Nano130 User Manual Application Note for 32-bit NuMicro® Family Rev.1.01 — Dec.17, 2012 Document Information Abstract This user manual provides information about hardware features and information about using this learning board. The Nu-LBNano130 learning board is similar to other development boards. Users can use it to develop and verify applications to emulate the real behavior. Apply to Nu-LB-Nano130 Board © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 1 of 60 User Manual NuMicro Family Table of Contents 1 INTRODUCTION ................................................................................................................. 3 1.1 Nu-LB-Nano130 ............................................................................................................................... 4 1.1.1PCB Placement and Connectors Location ................................................................................. 5 1.2 Nu-Link ICE Bridge Parts ............................................................................................................ 10 1.2.1Nu-Link ICE Layout and Connectors ........................................................................................ 11 1.3 LCD Interface................................................................................................................................. 13 1.3.1LCD Glass Board ....................................................................................................................... 13 1.3.2TFT LCM Board.......................................................................................................................... 15 2 GETTING STARTED ....................................................................................................... 17 2.1 Nu-LB-Nano130 I/O Extension Connectors.............................................................................. 18 2.1.1NuMicro Nano130 Pin Description......................................................................................... 18 2.2 Jumpers on Nu-LB-Nano130 ...................................................................................................... 41 2.2.1Jumper Settings ......................................................................................................................... 41 3 SCHEMATIC ..................................................................................................................... 42 4 BOM LIST .......................................................................................................................... 52 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 2 of 60 User Manual NuMicro Family 1 Introduction The Nu-LB-Nano130 is an evaluation board for NUVOTON’s Cortex™-M0 based Nano100 series microcontrollers, and provides a complete development environment for Nano130 microcontrollers which has 8/16K-byte internal SRAM and 32/64/128K-byte embedded flash, build-in 1.8V LDO, integrated LCD 4x40 dots, USB 2.0 full-speed port, RTC, 12-bit SAR ADC, 12-bit DAC, capacitive Touch-Key and provide high performance connectivity peripheral interfaces such as UART, SPI, I2C, I2S, GPIOs, EBI (External Bus Interface) and ISO-7816-3 for Smart card. It supports Brown-Out Detector, power down mode with RAM retention and fast wake up via all peripheral interfaces. The Nu-LB-Nano130 learning board is similar to other development boards. Users can use it to develop and verify applications to emulate the real behavior. The on-board chip covers Nano130 series features. The Nu-LBNano130 can be a real system controller to design users’ target systems. This user manual provides information about hardware features and information about using this learning board. The following figure shows the Nu-LB-Nano130 board. Figure 1-1 Nu-LB-Nano130 Board (Red) © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 3 of 60 User Manual NuMicro Family 1.1 Nu-LB-Nano130 The Nu-LB-Nano130 is built around the NuMicroTM Nano130 MCU and provides versatile external devices such as one SPI flash for data storage, one SD card slot supported by SPI port1, one I2C interface serial EEPROM, one UART port with a RS-232 level shifter for console connection (UART0) and one 5-pin SWD interface for ICE debugging. The following lists the main components of the Nu-LB-Nano130 board: Main Components: 13. MCU: NuMicroTM Nano130 MCU, which can run up to 32MHz operating speed. GPIO extension slot: GPIO extension slots that support all the GPI/O pins interface. AUDIO: On-board WAU8822 audio codec. I2C EEPROM: On-board 24LC64 I2C E2PROM. SPI FLASH: On-board 25Q16 SPI serial FLASH for data storage. UART: UART port0 connecting to Male type DSUB-9 connector. SD card Slot: One SD card slot supported by SPI port1. Smart card Slot: One Smart card slot supported by SMC port1. Nu-Link ICE bridge: On-board ICE bridge parts. SWD connector: One 5-pin SWD ICE port for ICE connection. LCD connector: Supports TN/STN LCD glass and TFT LCM module. Touch Pads: 5-key slider and 2-key touch pads onboard. DC power jack: 5V/1A power adapter input. 12. LDO: A 5V to 3.3V/1A LDO that supports Nano130 and on-board devices. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 4 of 60 User Manual NuMicro Family 1.1.1 PCB Placement and Connectors Location This section provides board placement and peripheral connectors’ information for using the Nu-LB-Nano130 board. The following figure shows the connectors’ location of Nu-LB-Nano130 board. CON3 CON4 CON2 JR2 DH2 JR1 J1 J3 J2 Figure 1-2 PCB Placement of Nu-LB-Nano130 Board © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 5 of 60 User Manual NuMicro Family AUDIO Line-in connector: J1 Audio Line-in connector of WAU8822 VCC_P R11 100K PA12 J1 G B C E F D A LINE_PLUG_INn R12 CC6 R2 5.6K R13 CC7 5.6K C/C,1uF C/C,220pF PJK-634 PHONE-PJK-631 ADAVSS R15 ADAVSS CC8 L2 5.6K R16 CC9 5.6K C/C,1uF C/C,220pF ADAVSS AUDIO HP out connector: J2 Stero audio HP output of WAU8822 VCC_P R14 100K J2 G B C E F D A CT1 HP_ROUT HP_LOUT CT2 T/C,100uF CC11 CC12 C/C,TBD C/C,TBD T/C,100uF PJK-634 PHONE-PJK-631 ADAVSS ADAVSS ADAVSS AUDIO SPK out connector: J3 Speaker output of WAU8822 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 6 of 60 User Manual NuMicro Family J3 ROUT LOUT 1 2 CC14 CC15 C/C,TBD C/C,TBD 2PX1 ADAVSS ADAVSS LCD interface: JR1,JR2 LCD interface for connecting LCD glass and TFT LCM board. LCD connectors VCC_P VCC_P VCC_P VCC_P JR1 1 3 5 7 9 11 13 15 17 19 nWE/SEG22 AD0/SEG24 SEG27 AD3/SEG33 AD5 AD7/SEG37 1 3 5 7 9 11 13 15 17 19 JR2 2 4 6 8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20 nRE/SEG23 AD1/SEG25 AD2/SEG32 AD4 AD6/SEG36 AD8/SEG38 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 SEG19 SEG17 SEG15 ALE/SEG11 SEG9 SEG3 SEG1 COM3 COM1 CONN RECT 10x2 GND GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 SEG18 SEG16 SEG14 nCS/SEG10 SEG8 SEG2 SEG0 COM2 COM0 CONN RECT 15x2 GND GND SMC Port 1 connector: P1 SMC Port 1 interface. SMC1(Smart Card) VCC_P R41 VCC_SMC 100K VCC_SMC CC61 CC62 C/C,0.1uF R42 10K R43 10K P1 SC1_PRES 10 9 C/C,1uF R44 S2 S1 10K GND GND SC1_CLK SC1_RST GND CLK RST VCC_SMC C4 C3 C2 C1 C4 C3 C2 C1 C8 C7 C6 C5 C8 C7 C6 C5 DAT SM Card Slot SC1_DAT GND © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 7 of 60 User Manual NuMicro Family SD card slot: J7 SD card interface (SPI mode only) connected to SPI port1. SPI1(SPI-SD) SD_VCC SD_VCC SPISS10 SPI1CLK SPIMISO10 SPIMOSI10 VCC_P 1 R45 2 Source SD_PWR_ON Gate 33 Si2301ADS 1 2 3 4 RP2 8 7 6 5 8P4R-4.7K Q2 FB7 GND LED3 FB CC66 15 J7 CC67 R46 GND WP RSV DO VSS CLK VDD VSS DI CS RSV HOLD C/C,0.1uF C/C,1uF C/C,0.1uF 14 2 220 GREEN_LED HOLD 3 1 CC65 C/C,1uF SD_VCC (P-FET) Drain CC42 GND CD# 11 10 GND SD_CTL SPIMISO10 8 7 6 5 4 3 2 1 9 SPI1CLK R49 SPIMOSI10 SPISS10 SD_INT 12 13 SD_CD 22 CC69 TBD VCC GND R50 100K SD/MMC SOCKET GND GND FB9 Operating voltage: 3.1V~3.6V FB GND SWD connector: DH2 5-pin SWD interface for Nano130. HEADER 5 1 2 3 4 5 DH2 VCC ICE_DAT ICE_CK ICE_RST GND USB Device connector: CON2 Mini-B type USB connector. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 8 of 60 User Manual NuMicro Family USB5.0V USB Device CON2 1 R36 27 USB_D- 2 USB_D+ 3 R37 27 4 CC38 CC39 TBD TBD 5 VBUS DD+ ID GND Shield Shield Shield Shield 6 7 8 9 USB MINI-B RECEP. GND GND Power adapter input: CON3 5V/1A power adapter input connector. CON3 VDD5.0V 1 2 GND IN 3 5V Power Adpater Power CON GND GND GND UART Port 0 connector: CON4 UART port 0 with RS-232 level shifter for debug console. CON4 5 9 4 8 3 7 2 6 1 RS232_RXD0 RS232_TXD0 11 10 DB9_MALE GND © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 9 of 60 User Manual NuMicro Family 1.2 Nu-Link ICE Bridge Parts The Nu-Link-Me is a Debug Adaptor which connects your PC's USB port to your target system (via Serial Wired Debug Port) and allows you to program and debug embedded programs on the target hardware. To use the Nu-Link-Me Debug adaptor with IAR or Keil, please refer to “Nuvoton NuMicro™ IAR ICE Driver User Manual“or “Nuvoton NuMicro™ Keil ICE Driver User Manual” for details. The two documents will be stored in the local hard disk when user installs each driver. Please refer to the following figure for Nu-Link ICE bridge parts on the Nu-LB-Nano130 board. Figure 1-3 Nu-Link ICE Bridge Parts © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 10 of 60 User Manual NuMicro Family Nu-Link ICE Layout and Connectors 1.2.1 The following figure shows the layout of the Nu-Link ICE connectors. ICE_USB1 DH1 Figure 1-4 Nu-Link ICE Layout and Connectors USB device connector: ICE_USB1 Mini-B type USB connector. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 11 of 60 User Manual NuMicro Family DVBUS5.0V D6 SS24A ICE_USB1 mini USB 5pin DD+ R33 R34 1 2 3 4 5 27 27 VCC DM DP NC GND SHIELD SHIELD SHIELD SHIELD 6 7 8 9 FB1 USB_MINI_B FB SWD interface: HEADER5 5-pin interface for SWD connector. DVBUS DVBUS R26 HEADER 5 1 2 3 4 5 DVBUS 100K R27 100K DDAT DCLK DRST DH1 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 12 of 60 User Manual NuMicro Family 1.3 LCD Interface The following shows the interface for LCD glass module and TFT LCM board and provides the connectors information. LCD interface: JR1 and JR2 30-pin + 20-pin interface for LCD module connectors. VCC VCC JR1 SEG19 SEG17 SEG15 ALE/SEG11 SEG9 SEG3 SEG1 COM3 COM1 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 SEG18 SEG16 SEG14 nCS/SEG10 SEG8 SEG2 SEG0 COM2 COM0 CONN RECT 15x2 GND GND VCC VCC JR2 nWE/SEG22 AD0/SEG24 SEG27 AD3/SEG33 AD5 AD7/SEG37 1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19 2 4 6 8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20 nRE/SEG23 AD1/SEG25 AD2/SEG32 AD4 AD6/SEG36 AD8/SEG38 CONN RECT 10x2 GND GND Figure 1-5 Connector Information 1.3.1 LCD Glass Board This section provides LCD glass board figure, layout and 4x40 LCD glass socket information. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 13 of 60 User Manual NuMicro Family Figure 1-6 LCD Glass Board LCD Interface: U1 48-pin interface for LCD glass socket. LCD 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 U1 SEG8 SEG9 nCS/SEG10 ALE/SEG11 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 nWE/SEG22 nRE/SEG23 AD0/SEG24 AD1/SEG25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 COM3 COM2 COM1 COM0 AD6/SEG36 AD7/SEG37 AD8/SEG38 SEG27 SEG3 SEG2 SEG1 SEG0 AD3/SEG33 AD2/SEG32 Figure 1-7 LCD Glass Socket Information © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 14 of 60 User Manual NuMicro Family 1.3.2 TFT LCM Board This section provides information about 240x320 TFT panel (GFT024CA240320). Figure 1-5 TFT LCM Board LCM interface: CON1 39-pin FPC connector for GFT024CA240320. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 15 of 60 User Manual NuMicro Family VCC CON1 nCS/SEG10 ALE/SEG11 nWE/SEG22 nRE/SEG23 VCC R1 10K SEG19 SEG27 AD0/SEG24 AD1/SEG25 AD2/SEG32 AD3/SEG33 AD4 AD5 AD6/SEG36 AD7/SEG37 LCD_RST FMARK CC1 IM3 C/C,1uF BL_A GND VCC BL_K BL_A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 NC NC NC NC GND CS RS WR RD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 DB16 DB17 RESET FMARK IM0 IM3 IOVCC VCC A1 A2 A3 A4 PWM K FPC 1X39 GFT024CA240320 VCC CC2 C/C,1uF GND VCC CC3 C/C,1uF GND GND © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 16 of 60 User Manual NuMicro Family 2 Getting Started There are a few hardware jumpers need to be set for selecting corresponding configuration you want. The following sections provide multi-function I/O information and all the jumper settings for configuring your NuLB-Nano130 board. Due to many IP function are sharing the same I/O pins in Nano130 series MCU, please be carefully to set on-board jumpers to avoid conflicts between functions. JP2 J4 J5 JP1 Figure 1-6 Nano130 Learning Board © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 17 of 60 User Manual NuMicro Family 2.1 Nu-LB-Nano130 I/O Extension Connectors The Nu-LB-Nano130 has 55 I/O pads and 13 power pads for a total of 68 pads. Two 50-pin male headers J4 and J5 can be connected to a daughterboard or standard wrapping board to the Nu-LB-Nano130 board. Each pin on J4 and J5 can be used by a daughterboard after disconnecting it from the corresponding function block on the Nu-LB-Nano130 board. Please refer to the following for detailed pin description. GPIO extension interface: J4, J5 Two 40 pin interfaces support power, ground, reset and all GPI/O pins interface. The connection can be made by soldering wires directly to these pads, or by using 2.54 mm pitch headers and sockets. GPIO extersion VCC_P VCC_P J5 PB1 PB3 PD7 PD15 PC4 PC2 PE4 PE2 PE0 PC12 PC10 PC8 PA14 PA12 PA1 PA3 PA5 PA7 PD1 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 SPIMISO10 SPISS10 SEG2 SEG0 COM2 COM0 SPIMOSI00 SPI0CLK I2S_MCLK PWM1_0 CTK14 CTK12 RXD0 PA12 ADC1 ADC3 AD8/SEG38 AD6/SEG36 SC1_DAT 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 J4 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 SPIMOSI10 PB0 SPI1CLK PB2 SEG3 PD6 SEG1 PD14 COM3 PC5 COM1 PC3 PE6 PE6 SPIMISO00 PE3 SPISS00 PE1 PC13 PC13 CTK15 PC11 CTK13 PC9 TXD0 PA15 CTK11 PA13 ADC0 PA0 ADC2 PA2 ADC4 PA4 AD7/SEG37PA6 SC1_CLK PD0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 PE8 PB6 PB4 PD12 PD10 PD8 PA9 PA11 PB13 PE13 PE15 PF5 PB15 PC15 PC7 PD4 PD2 1 SEG9 3 ALE/SEG11 5 RXD1 7 SEG15 9 SEG17 11 SEG19 13 I2C0SCL 15 nRE/SEG23 17 AD1/SEG25 19 SEG27 21 PE15 23 25 27 CTK7 29 nINT1 31 AD3/SEG33 33 AD5 35 SC1_PRES/I2S_DIN37 SC1_PWR/I2S_WS 39 CONN RECT 20x2 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 SEG8 PE7 nCS/SEG10PB7 TXD1 PB5 SEG14 PD13 SEG16 PD11 SEG18 PD9 I2C0SDA PA8 nWE/SEG22PA10 AD0/SEG24PB12 nINT0 PB14 PE14 PE14 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 PB8 PB8 CTK6 PF4 AD2/SEG32PC14 AD4 PC6 I2S_DOUT PD5 SC1_RST/I2S_BCLK PD3 CONN RECT 20x2 GND GND 2.1.1 NuMicro Nano130 Pin Description Pin No. Pin Name Pin Type PE.13 I/O LCD_SEG27 O PB.14 I/O Description General purpose digital I/O pin 1 2 LCD segment output 27 at LQFP128 General purpose digital I/O pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 18 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description INT0 I External interrupt0 input pin SC2_CD I SmartCard2 card detect SPI2_SS1 O SPI2 2nd slave select pin LCD_SEG12 O LCD segment output 12 at LQFP64 LCD_SEG26 O LCD segment output 26 at LQFP128 PB.13 I/O General purpose digital I/O pin EBI_AD1 I/O EBI Address/Data bus bit1 LCD_SEG11 O LCD segment output 11 at LQFP64 LCD_SEG25 O LCD segment output 25 at LQFP128 PB.12 I/O General purpose digital I/O pin EBI_AD0 I/O EBI Address/Data bus bit0 CLKO O Frequency Divider output pin LCD_SEG10 O LCD segment output 10 at LQFP64 LCD_SEG24 O LCD segment output 24 at LQFP128 3 4 5 NC 6 X32O O External 32.768 kHz crystal output pin 7 X32I I External 32.768 kHz crystal input pin 8 NC PA.11 I/O General purpose digital I/O pin I2C1_SCL I/O I2C 1 clock pin 9 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 19 of 60 User Manual NuMicro Family Pin No. 10 Pin Name Pin Type Description EBI_nRD O EBI read enable output pin SC0_RST O SmartCard0 RST pin SPI2_MOSI0 I/O LCD_SEG9 O LCD segment output 9 at LQFP64 LCD_SEG23 O LCD segment output 23 at LQFP128 PA.10 I/O General purpose digital I/O pin I2C1_SDA I/O I2C 1 data I/O pin EBI_nWR O EBI write enable output pin SC0_PWR O SmartCard0 Power pin SPI2_MISO0 I/O LCD_SEG8 O LCD segment output 8 at LQFP64 LCD_SEG22 O LCD segment output 22 at LQFP128 PA.9 I/O General purpose digital I/O pin I2C0_SCL I/O I2C 0 clock pin SC0_DAT I/O SmartCard0 DATA pin SPI2_CLK O SPI2 serial clock pin LCD_SEG7 O LCD segment output 7 at LQFP64 LCD_SEG21 O LCD segment output 21 at LQFP128 PA.8 I/O General purpose digital I/O pin I2C0_SDA I/O I2C 0 data I/O pin SPI2 1st MOSI (Master Out, Slave In) pin SPI2 1st MISO (Master In, Slave Out) pin 11 12 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 20 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description SC0_CLK O SmartCard0 clock pin SPI2_SS0 O SPI2 1st slave select pin LCD_SEG6 O LCD segment output 6 at LQFP64 LCD_SEG20 O LCD segment output 20 at LQFP128 PD.8 I/O LCD_SEG19 O PD.9 I/O LCD_SEG18 O PD.10 I/O LCD_SEG17 O PD.11 I/O LCD_SEG16 O PD.12 I/O LCD_SEG15 O PD.13 I/O LCD_SEG14 O PB.4 I/O General purpose digital I/O pin UART1_RXD I UART1 Data receiver input pin SC0_CD I SmartCard0 card detect pin SPI2_SS0 O SPI2 1st slave select pin General purpose digital I/O pin 13 LCD segment output 19 at LQFP128 General purpose digital I/O pin 14 LCD segment output 18 at LQFP128 General purpose digital I/O pin 15 LCD segment output 17 at LQFP128 General purpose digital I/O pin 16 LCD segment output 16 at LQFP128 General purpose digital I/O pin 17 LCD segment output 15 at LQFP128 General purpose digital I/O pin 18 LCD segment output 14 at LQFP128 19 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 21 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description LCD_SEG5 O LCD segment output 5 at LQFP64 LCD_SEG13 O LCD segment output 13 at LQFP128 PB.5 I/O UART1_TXD O UART1 Data transmitter output pin SC0_RST O SmartCard0 RST pin SPI2_CLK O SPI2 serial clock pin LCD_SEG4 O LCD segment output 4 at LQFP64 LCD_SEG12 O LCD segment output 12 at LQFP128 PB.6 I/O UART1_nRTS O UART1 Request to Send output pin EBI_ALE O EBI address latch enable output pin SPI2_MISO0 I/O LCD_SEG3 O LCD segment output 3 at LQFP64 LCD_SEG11 O LCD segment output 11 at LQFP128 PB.7 I/O General purpose digital I/O pin UART1_nCTS I UART1 Clear to Send input pin EBI_nCS O EBI chip select enable output pin SPI2_MOSI0 I/O LCD_SEG2 O LCD segment output 2 at LQFP64 LCD_SEG10 O LCD segment output 10 at LQFP128 General purpose digital I/O pin 20 General purpose digital I/O pin 21 SPI2 2nd MISO (Master In, Slave Out) pin 22 SPI2 1st MOSI (Master Out, Slave In) pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 22 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type 23 24 Description NC LDO_CAP P LDO output pin 25 NC 26 NC 27 VDD P 28 Power supply for I/O ports and LDO source NC 29 VSS P Ground 30 VSS P Ground 31 VSS P Ground 32 VSS P Ground 33 PE.12 I/O General purpose digital I/O pin 34 PE.11 I/O General purpose digital I/O pin 35 PE.10 I/O General purpose digital I/O pin 36 PE.9 I/O General purpose digital I/O pin PE.8 I/O General purpose digital I/O pin LCD_SEG9 O PE.7 I/O LCD_SEG8 O 37 LCD segment output 9 at LQFP128 General purpose digital I/O pin 38 39 40 LCD segment output 8 at LQFP128 NC USB_VBUS USB POWER SUPPLY: From USB Host or HUB. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 23 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description 41 USB_VDD33_C AP USB Internal Power Regulator Output 3.3V Decoupling Pin 42 USB_D- USB USB Differential Signal D- 43 USB_D+ USB USB Differential Signal D+ PB.0 I/O General purpose digital I/O pin UART0_RXD I UART0 Data receiver input pin SPI1_MOSI0 I/O LCD_SEG1 O LCD segment output 1 at LQFP64 LCD_SEG7 O LCD segment output 7 at LQFP128 PB.1 I/O UART0_TXD O SPI1_MISO0 I/O LCD_SEG0 O LCD segment output 0 at LQFP64 LCD_SEG6 O LCD segment output 6 at LQFP128 PB.2 I/O UART0_nRTS O UART0 Request to Send output pin EBI_nWRL O EBI low byte write enable output pin SPI1_CLK O SPI1 serial clock pin LCD_COM3 O LCD common output 3 at LQFP64 LCD_SEG5 O LCD segment output 5 at LQFP128 PB.3 I/O 44 45 SPI1 1st MOSI (Master Out, Slave In) pin General purpose digital I/O pin UART0 Data transmitter output pin SPI1 1st MISO (Master In, Slave Out) pin General purpose digital I/O pin 46 47 General purpose digital I/O pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 24 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description UART0_nCTS I UART0 Clear to Send input pin EBI_nWRH O EBI high byte write enable output pin SPI1_SS0 O SPI1 1st slave select pin LCD_COM2 O LCD common output 2 at LQFP64 LCD_SEG4 O LCD segment output 4 at LQFP128 PD.6 I/O LCD_SEG3 O PD.7 I/O LCD_SEG2 O PD.14 I/O LCD_SEG1 O PD.15 I/O LCD_SEG0 O PC.5 I/O SPI0_MOSI1 O SPI0 2nd MOSI (Master Out, Slave In) pin LCD_COM3 O LCD common output 3 at LQFP128 PC.4 I/O SPI0_MISO1 I SPI0 2nd MISO (Master In, Slave Out) pin LCD_COM2 O LCD common output 2 at LQFP128 PC.3 I/O General purpose digital I/O pin 48 LCD segment output 3 at LQFP128 General purpose digital I/O pin 49 LCD segment output 2 at LQFP128 General purpose digital I/O pin 50 LCD segment output 1 at LQFP128 General purpose digital I/O pin 51 52 53 54 LCD segment output 0 at LQFP128 General purpose digital I/O pin General purpose digital I/O pin General purpose digital I/O pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 25 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description SPI0_MOSI0 O SPI0 1st MOSI (Master Out, Slave In) pin I2S_DO O I2S data output SC1_RST O SmartCard1 RST pin LCD_COM1 O LCD common output 1 at LQFP64 LCD_COM1 O LCD common output 1 at LQFP128 PC.2 I/O SPI0_MISO0 I SPI0 1st MISO (Master In, Slave Out) pin I2S_DI I I2S data input SC1_PWR O SmartCard1 PWR pin LCD_COM0 O LCD common output 0 at LQFP64 LCD_COM0 O LCD common output 0 at LQFP128 PC.1 I/O General purpose digital I/O pin SPI0_CLK I/O SPI0 serial clock pin I2S_BCLK I/O I2S bit clock pin SC1_DAT I/O SmartCard1 DATA pin LCD_DH2 O LCD external capacitor pin of charge pump circuit at LQFP64 LCD_DH2 O LCD external capacitor pin of charge pump circuit at LQFP128 PC.0 I/O General purpose digital I/O pin SPI0_SS0 I/O SPI0 1st slave select pin General purpose digital I/O pin 55 56 57 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 26 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type I2S_LRCLK I/O SC1_CLK O SmartCard1 clock pin LCD_DH1 O LCD external capacitor pin of charge pump circuit at LQFP64 LCD_DH1 O LCD external capacitor pin of charge pump circuit at LQFP128 58 PE.6 I/O General purpose digital I/O pin 59 LCD_VLCD AO LCD power supply pin 60 61 Description I2S left right channel clock NC PE.5 General purpose digital I/O pin PB.11 I/O General purpose digital I/O pin PWM1_CH0 I/O PWM1 Channel0 output TM3 O SC2_DAT I/O SmartCard2 DATA pin SPI0_MISO0 I/O SPI0 1st MISO (Master In, Slave Out) pin LCD_V1 O LCD Unit voltage for LCD charge pump circuit at LQFP64 LCD_V1 O LCD Unit voltage for LCD charge pump circuit at LQFP128 PB.10 I/O General purpose digital I/O pin SPI0_SS1 I/O SPI0 2nd slave select pin TM2 O Timer3 external counter input 62 63 Timer2 external counter input © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 27 of 60 User Manual NuMicro Family Pin No. 64 Pin Name Pin Type Description SC2_CLK O SPI0_MOSI0 I/O LCD_V2 O LCD driver biasing voltage at LQFP64 LCD_V2 O LCD driver biasing voltage at LQFP128 PB.9 I/O General purpose digital I/O pin SPI1_SS1 I/O SPI1 2nd slave select pin TM1 O Timer1 external counter input SC2_RST O SmartCard2 RST pin INT0 I External interrupt0 input pin LCD_V3 O LCD driver biasing voltage at LQFP64 LCD_V3 O LCD driver biasing voltage at LQFP128 PE.4 I/O General purpose digital I/O pin SPI0_MOSI0 I/O SPI0 1st MOSI (Master Out, Slave In) pin PE.3 I/O General purpose digital I/O pin SPI0_MISO0 I/O SPI0 1st MISO (Master In, Slave Out) pin PE.2 I/O General purpose digital I/O pin SPI0_CLK O PE.1 I/O General purpose digital I/O pin PWM1_CH3 I/O PWM1 Channel3 output SPI0_SS0 O SPI0 1st slave select pin SmartCard2 clock pin SPI0 1st MOSI (Master Out, Slave In) pin 65 66 67 68 SPI0 serial clock pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 28 of 60 User Manual NuMicro Family Pin No. 69 Pin Name Pin Type Description PE.0 I/O General purpose digital I/O pin PWM1_CH2 I/O PWM1 Channel2 output I2S_MCLK O PC.13 I/O SPI1_MOSI1 O SPI1 2nd MOSI (Master Out, Slave In) pin PWM1_CH1 O PWM1 Channel1 output SNOOPER I Snooper pin INT0 I External interrupt 0 input pin I2C0_SCL O I2C 0 clock pin PC.12 I/O SPI1_MISO1 I SPI1 2nd MISO (Master In, Slave Out) pin PWM1_CH0 O PWM1 Channel0 output INT0 I External interrupt0 input pin I2C0_SDA I/O I2C 0 data I/O pin PC.11 I/O General purpose digital I/O pin SPI1_MOSI0 O SPI1 1st MOSI (Master Out, Slave In) pin UART1_TXD O UART1 Data transmitter output pin CTK15 I Touch key 15 LCD_SEG31 O LCD segment output 31 at LQFP64 PC.10 I/O I2S master clock output pin General purpose digital I/O pin 70 71 72 73 General purpose digital I/O pin General purpose digital I/O pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 29 of 60 User Manual NuMicro Family Pin No. 74 Pin Name Pin Type Description SPI1_MISO0 I SPI1 1st MISO (Master In, Slave Out) pin UART1_RXD I UART1 Data receiver input pin CTK14 I Touch key 14 LCD_SEG30 O LCD segment output 30 at LQFP64 PC.9 I/O General purpose digital I/O pin SPI1_CLK I/O SPI1 serial clock pin I2C1_SCL I/O I2C 1 clock pin CTK13 I Touch key 13 LCD_SEG29 O LCD segment output 29 at LQFP64 PC.8 I/O General purpose digital I/O pin SPI1_SS0 I/O SPI1 1st slave select pin EBI_MCLK O I2C1_SDA I/O CTK12 I Touch key 12 LCD_SEG28 O LCD segment output 28 at LQFP64 PA.15 I/O General purpose digital I/O pin PWM0_CH3 I/O PWM0 Channel3 output I2S_MCLK O I2S master clock output pin TC3 I Timer3 capture input SC0_PWR O SmartCard0 Power pin EBI external clock output pin 75 76 I2C 1 data I/O pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 30 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description UART0_TXD O UART0 Data transmitter output pin LCD_SEG27 O LCD segment output 27 at LQFP64 PA.14 I/O General purpose digital I/O pin PWM0_CH2 I/O PWM0 Channel2 output EBI_AD15 I/O EBI Address/Data bus bit15 TC2 I Timer 2 capture input UART0_RXD I UART0 Data receiver input pin LCD_SEG26 O LCD segment output 26 at LQFP64 PA.13 I/O General purpose digital I/O pin PWM0_CH1 I/O PWM0 Channel1 output EBI_AD14 I/O EBI Address/Data bus bit14 TC1 I I2C0_SCL I/O I2C 0 clock pin CTK11 I Touch key 11 LCD_SEG25 O LCD segment output 25 at LQFP64 PA.12 I/O General purpose digital I/O pin PWM0_CH0 I/O PWM0 Channel0 output EBI_AD13 I/O EBI Address/Data bus bit13 TC0 I I2C0_SDA I/O 77 78 79 Timer1 capture input Timer 0 capture input I2C 0 data I/O pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 31 of 60 User Manual NuMicro Family Pin No. 80 Pin Name Pin Type Description CTK10 I Touch key 10 LCD_SEG24 O LCD segment output 24 at LQFP64 ICE_DAT I/O Serial Wired Debugger Data pin PF.0 I/O General purpose digital I/O pin INT0 I External interrupt0 input pin ICE_CLK I Serial Wired Debugger Clock pin PF.1 I/O General purpose digital I/O pin CLKO O Frequency Divider output pin INT1 I External interrupt1 input pin 81 82 83 NC VDD P 84 Power supply for I/O ports and LDO source for internal PLL and digital circuit NC 85 VSS P Ground 86 VSS P Ground 87 AVSS AP Ground Pin for analog circuit 88 AVSS AP Ground Pin for analog circuit PA.0 I/O General purpose digital I/O pin AD0 AI ADC analog input0 SC2_CD I SmartCard2 card detect CTK8 AI Touch key 1 89 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 32 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description PA.1 I/O General purpose digital I/O pin AD1 AI ADC analog input1 EBI_AD12 I/O EBI Address/Data bus bit12 CTK9 AI Touch key 9 PA.2 I/O General purpose digital I/O pin AD2 AI ADC analog input2 EBI_AD11 I/O EBI Address/Data bus bit11 UART1_RXD I LCD_SEG23 AO LCD segment output 23 at LQFP64 PA.3 I/O General purpose digital I/O pin AD3 AI ADC analog input3 EBI_AD10 I/O EBI Address/Data bus bit10 UART1_TXD O UART1 Data transmitter output pin LCD_SEG22 AO LCD segment output 22 at LQFP64 PA.4 I/O General purpose digital I/O pin AD4 AI ADC analog input4 EBI_AD9 I/O EBI Address/Data bus bit9 SC2_PWR O I2C0_SDA I/O I2C 0 data I/O pin LCD_SEG21 AO LCD segment output 21 at LQFP64 90 91 92 UART1 Data receiver input pin 93 SmartCard2 Power pin © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 33 of 60 User Manual NuMicro Family Pin No. 94 Pin Name Pin Type Description LCD_SEG39 AO LCD segment output 39 at LQFP128 PA.5 I/O General purpose digital I/O pin AD5 AI ADC analog input5 EBI_AD8 I/O EBI Address/Data bus bit8 SC2_RST O I2C0_SCL I/O I2C 0 clock pin LCD_SEG20 AO LCD segment output 20 at LQFP64 LCD_SEG38 AO LCD segment output 38 at LQFP128 PA.6 I/O General purpose digital I/O pin AD6 AI ADC analog input6 EBI_AD7 I/O EBI Address/Data bus bit7 TC3 I Timer3 capture input SC2_CLK O SmartCard2 clock pin PWM0_CH3 O PWM0 Channel3 output LCD_SEG19 AO LCD segment output 19 at LQFP64 LCD_SEG37 AO LCD segment output 37 at LQFP128 PA.7 I/O General purpose digital I/O pin AD7 AI ADC analog input7 EBI_AD6 I/O EBI Address/Data bus bit6 TC2 I SmartCard2 RST pin 95 96 Timer2 capture input © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 34 of 60 User Manual NuMicro Family Pin No. 97 Pin Name Pin Type SC2_DAT I/O PWM0_CH2 O PWM0 Channel2 output CTK_CAP AI Touch key Capacitor pin LCD_SEG18 AO LCD segment output 18 output at LQFP64 LCD_SEG36 AO LCD segment output 36 output at LQFP128 VREF AP Voltage reference input for ADC 98 99 Description SmartCard2 DATA pin NC AVDD AP Power supply for internal analog circuit PD.0 I/O General purpose digital I/O pin UART1_RXD I UART1 Data receiver input pin SPI2_SS0 I/O SC1_CLK O SmartCard1 clock pin CTK0 AI Touch key 0 AD8 AI ADC analog input8 PD.1 I/O General purpose digital I/O pin TX1 O SPI2_CLK I/O SPI2 serial clock pin SC1_DAT I/O SmartCard1 DATA pin AD9 AI ADC analog input9 CTK1 AI Touch key 1 SPI2 2nd slave select pin 100 UART1 Data transmitter output pin 101 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 35 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type PD.2 I/O UART1_nRTS 102 I2S_LRCLK I/O SPI2_MISO0 I SPI2 1st MISO (Master In, Slave Out) pin SC1_PWR O SmartCard1 Power pin AD10 AI ADC analog input10 CTK2 AI Touch key 2 PD.3 I/O General purpose digital I/O pin I2S left right channel clock UART1 Clear to Send input pin I2S_BCLK I/O SPI2_MOSI0 O SPI2 1st MOSI (Master Out, Slave In) pin SC1_RST O SmartCard1 RST pin AD11 AI ADC analog input11 CTK3 AI Touch key 3 104 105 General purpose digital I/O pin UART1 Request to Send output pin UART1_nCTS 103 Description I2S bit clock pin NC PD.4 I/O General purpose digital I/O pin I2S_DI I I2S data input SPI2_MISO1 I SPI2 2nd MISO (Master In, Slave Out) pin SC1_CD I SmartCard1 card detect CTK4 AI Touch key 4 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 36 of 60 User Manual NuMicro Family Pin No. 106 Pin Name Pin Type Description LCD_SEG35 AO LCD segment output 35 at LQFP128 PD.5 I/O General purpose digital I/O pin I2S_DO O I2S data output SPI2_MOSI1 O SPI2 2nd MOSI (Master Out, Slave In) pin CTK5 AI Touch key 5 LCD_SEG34 AO LCD segment output 34 at LQFP128 PC.7 I/O General purpose digital I/O pin DA1_OUT AO DAC 1 output EBI_AD5 I/O EBI Address/Data bus bit5 TC1 I Timer1 capture input PWM0_CH1 O PWM1 Channel1 output LCD_SEG17 AO LCD segment output 17 at LQFP64 PC.6 I/O General purpose digital I/O pin DA0_OUT I EBI_AD4 I/O TC0 I 107 DAC0 output EBI Address/Data bus bit4 108 SC1_CD Timer 0 capture input SmartCard1 card detect pin PWM0_CH0 O PWM0 Channel0 output PC.15 I/O General purpose digital I/O pin EBI_AD3 I/O EBI Address/Data bus bit3 109 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 37 of 60 User Manual NuMicro Family Pin No. 110 Pin Name Pin Type Description TC0 I Timer0 capture input PWM1_CH2 O PWM1 Channel1 output LCD_SEG16 AO LCD segment output 16 at LQFP64 LCD_SEG33 AO LCD segment output 33 at LQFP128 PC.14 I/O General purpose digital I/O pin EBI_AD2 I/O EBI Address/Data bus bit2 PWM1_CH3 I/O PWM1 Channel3 output LCD_SEG15 AO LCD segment output 15 at LQFP64 LCD_SEG32 AO LCD segment output 32 at LQFP128 PB.15 I/O General purpose digital I/O pin INT1 I External interrupt1 input pin SNOOPER I Snooper pin SC1_CD I SmartCard1 card detect LCD_SEG14 AO LCD segment output 14 at LQFP64 LCD_SEG31 AO LCD segment output 31 at LQFP128 111 112 NC 113 XT1_IN O External 4~24 MHz crystal output pin 114 XT1_OUT I External 4~24 MHz crystal input pin 115 NC © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 38 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description 116 nRESET I External reset input: Low active, set this pin low reset chip to initial state. With internal pull-up. 117 VSS P Ground 118 VSS P Ground 119 120 NC VDD P 121 Power supply for I/O ports and LDO source for internal PLL and digital circuit NC PF.4 I/O General purpose digital I/O pin I2C0_SDA I/O I2C 0 data I/O pin CTK6 AI Touch key 6 PF.5 I/O Digital GPI/O pin I2C0_SCL I/O I2C 0 clock pin CTK7 AI Touch key 7 124 VSS P Ground 125 PVSS I/O PLL Ground PB.8 I/O General purpose digital I/O pin STADC I ADC external trigger input. TM0 I Timer0 external counter input INT0 I External interrupt0 input pin SC2_PWR O SmartCard2 Power pin 122 123 126 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 39 of 60 User Manual NuMicro Family Pin No. Pin Name Pin Type Description LCD_SEG13 AO LCD segment output 13 at LQFP64 LCD_SEG30 AO LCD segment output 30 at LQFP128 PE.15 I/O General purpose digital I/O pin LCD_SEG29 O PE.14 I/O LCD_SEG28 O 127 LCD segment output 29 at LQFP128 General purpose digital I/O pin 128 LCD segment output 28 at LQFP128 Note: Pin Type I=Digital Input, O=Digital Output; AI=Analog Input; AO=Analog Output; P=Power Pin; AP=Analog Power When some pin is not available in some packages, hardware will auto pull this pin high. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 40 of 60 User Manual NuMicro Family 2.2 Jumpers on Nu-LB-Nano130 The following section describes all the jumpers on Nano130 Learning board. 2.2.1 Jumper Settings The jumper settings are used to configure the PD4(JP1) and peripherals’ power source(JP2). Since the PD4 has two roles on this learning board, please confirm to selet right side of JP1 before using the I2S and SC1 function. Jumper Description Location PD4 onboard function selection: JP1 SC1_PRES SC1_PRES/I2S_DIN I2S_DIN JP1 1 2 3 1-2:SC1_PRES 2-3:I2S_DIN 3PX1 VCC JP2 VCC_P Peripherals power source selection: VDD3.3V JP2 1 2 3 1-2:Power from VDD3.3V 2-3:Power from VCC 3PX1 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 41 of 60 User Manual NuMicro Family 3 Schematic /// UART & ADC/// ADC[0..4] TXD[0..1] RXD[0..1] ADC[0..4] ADC x 5 UART_TXD[0..1] UART_RXD[0..1] RS-232 Transceiver UVDD33 UART Port 0 CC55 C/C,1uF FB8 5 9 4 8 3 7 2 6 1 FB VCC_P CC56 CC57 C/C,0.1uF C/C,1uF RS232_RXD0 CC58 C/C,1uF CC59 C/C,1uF VR AVCC_MCU 1 2 3 4 5 6 7 8 U7 C1+ V+ C1C2+ C2VT2_OUT R2_IN VCC GND T1_OUT R1_IN R1_OUT T1_IN T2_IN R2_OUT 16 15 14 13 12 11 10 9 RS232_TXD0 RS232_TXD0 RS232_RXD0 UART_RXD0 UART_TXD0 GND CON4 11 10 DB9_MALE GND SP3232ECN R5 0 ADC1 ADC1 VR1 Operating voltage: 3.0V~5V (VIH:2V/VIL:0.8V) 50K CC4 R6 C/C,0.01uF ADC_GND 100 ADC_GND IrDA transceiver UART Port 1 UART_TXD1 UART_RXD1 VCC_P U8 8 VLED 7 6 5 IrDA_TXD IrDA_RXD IrDA_SD TXD RXD SD 4 AGND 3 VCC_P SHIELD VCC R40 10K CC60 1 GND C/C,0.1uF AVCC_MCU NC 2 HSDL-3201 GND Thermistor GND BAT_VD R2 100K VBAT R23 ADC0 ADC0 ADC4 NTC1 GND Operating voltage: 2.7V~3.6V (VIH:2/3Vcc/VIL:1/3Vcc) 0 ADC4 CC3 CC2 C/C,0.1uF C/C,0.1uF 100K ADC_GND Title ADC_GND ADC_GND NANO130/ADC Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 1 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 42 of 60 User Manual NuMicro Family /// Audio/// VCC_P I2C0SDA I2C0SCL I2C0SDA I2C0SCL I2S_MCLK I2S_LRC I2S_BCLK I2S_DACDATA I2S_ADCDATA 1 2 3 4 CC5 C/C,0.1uF VCC_P VCC EEPROM ADDRESS:0H VCC_P I2S_MCLK I2S_LRC I2S_BCLK I2S_DACDATA I2S_ADCDATA I2C Port R7 U2 I2C-EEPROM A0 A1 A2 GND R9 22 2.2K R10 22 I2C0SCL I2C0SDA 24LC64 GND R8 2.2K 8 7 6 5 VCC WP SCL SDA E-C Right channel F-D Left channel GND R11 PA12 G B C E F D A R12 LINE_PLUG_INn 5.6K CC6 R13 5.6K CC7 F Operating voltage: 2.5V~5.5V (VIH:0.7Vcc/VIL:0.3Vcc) 100K J1 C D C/C,1uF A B E G C/C,220pF PJK-634 PHONE-PJK-631 VCC_P ADAVSS VCC_P R15 ADAVSS CAVDD CC8 R14 C/C,220pF 20 19 AUXR AUXL 26 U3 CT1 SPKVDD C/C,1uF 31 CC9 AVDD 5.6K DCVDD DBVDD R16 13 14 100K 5.6K HP_ROUT HP_LOUT CC13 C/C,1uF 2 1 5 4 MICLN MICLP MIC2 C/C,1uF L2 R2 OUT3 OUT4 47K CC18 CC19 C/C,100pF C/C,4.7uF C/C,4.7uF C/C,0.1uF WAU8822 QFN_32 ADAVSS ADAVSS ADAVSS DGND CC17 24 28 2.2K MICBIAS VMID CC16 2.2K 12 32 27 MICBIAS R19 SPKGND AGND R17 R18 GND ADAVSS ROUT2 LOUT2 HP_LOUT CT2 T/C,100uF 22 CC12 C/C,TBD C/C,TBD 23 25 PJK-634 PHONE-PJK-631 J3 1 2 CC14 CC15 C/C,TBD C/C,TBD ADAVSS R99 I2S_MCLK I2S_DACDATA I2S_ADCDATA I2S_BCLK I2S_LRC CC99 CAVDD CC21 CC22 CC23 CC24 CT3 C/C,0.1uF C/C,4.7uF C/C,4.7uF C/C,4.7uF C/C,0.1uF T/C,10uF/10V FB6 GND FB FB CC25 CC26 C/C,0.1uF C/C,4.7uF Title GND 33 C/C,20pF VCC_P CC20 ADAVSS ADAVSS ROUT LOUT I2C0SDA I2C0SCL PHn GND CAVDD ADAVSS 21 ADAVSS FB5 GND CC11 T/C,100uF J2 2PX1 ADAVSS Operating voltage: 2.5V~5.5V (VIH:0.7Vcc/VIL:0.3Vcc) VCC_P 30 G B C E F D A ADAVSS MICLN MICLP MICRN MICRP LRC BCLK ADCDAT DACDAT MCLK CSB/GPIO1 SCLK SDIN MODE MIC1 3 6 HP_ROUT 7 8 9 10 11 15 16 17 18 CC10 ADAVSS 29 PHn ADAVSS AUDIO Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 2 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 43 of 60 User Manual NuMicro Family /// HMI /// External INT/SNOOPER VCC R21 PB8 220 PB8 2 PWM1_0 nINT1 3 1 2 VCC R20 2 PWM1_0 1K SP1 Buzzer CKT[6..7] CKT[11..15] R22 1 Q1 2N3904 SW PWM1_0 B 12K 2 CTK[6..7] CTK[11..15] C 1 nINT[0..1] 3 nINT[0..1] PWM OUT 1 BU1 LED indicator E LED1 GREEN_LED (Top View ) SOT-23 GND PB8 GND Touch Key K2 K1 1 CTKey 1 CTKey CTKey _SLIDER 3 K3 1 5 CTK6 4 CTK7 2 CTK15 CTK14 CTK13 CTK12 CTK11 VCC VCC CT4 CT5 T/C,22uF/10V T/C,22uF/10V Title GND GND NANO130/HMI Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 3 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 44 of 60 User Manual NuMicro Family /// ICE Parts /// DVBUS DVBUS CC27 DVBUS R26 X1 R25 C/C,20pF 12MHz HEADER 5 CC28 1 2 3 4 5 DVBUS 100K DRST C/C,20pF 100K DVBUS DVBUS ICELED ICPLED RED GREEN BUSY 1 2 1 DVBUS KPT-2012 IDLE1 KP-2012 DVBUS CC86 CC87 C/C,1uF C/C,0.1uF RED 2 1 KPT-2012 ICP1 KP-2012 ICPLED KPT-2012 ICE1 KP-2012 1 DVBUS R28 100K TICERST TICECLK R30 R32 R29 100K TICEDAT R31 100K 0 1K DVBUS5.0V ICE_RST TICERST D6 CC30 R33 R34 J6 CC29 2PX1 C/C,1uF 27 27 1 2 3 4 5 ICE_USB1 mini USB 5pin 6 SHIELD 7 SHIELD 8 SHIELD 9 SHIELD VCC DM DP NC GND FB1 FB USB_MINI_B DVBUS 2 1 OUT IN GND OUT DCLK DDAT VBAT 4 3 1 2 CT8 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 SS24A 2 DVBUS5.0V TICERST DVBUS5.0V C/C,1uF U4 RT9164A-3.3v TICEDAT TICECLK 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 NUC120 LQFP 64 PA4/ADC4 PA3/ADC3 PA2/ADC2 PA1/ADC1 PA0/ADC0 AVSS ICE_CK ICE_DAT PA12/PWM0 PA13/PWM1 PA14/PWM2 PA15/PWM3 PC8/SS10 PC9/SPCLK1 PC10/SDI10 PC11/SDO10 ICELED KPT-2012 KP-2012 3.3V/1A LDO ICE_RST ICE_RST 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 RP1 8 7 6 5 8P4R-330 2 1 2 3 4 STADC/TM0/PB8 PVSS VDD1 VSS1 /RESET XT1_In XT1_Out INT1/PB15 CPP1/PC14 CPN1/PC15 CPP0/PC6 CPN0/PC7 AVDD ADC7/PA7 ADC6/PA6 ADC/PA5 INT0/PB14 CPO1/PB13 CPO0/PB12 X32I X32O I2C1SCL/PA11 I2C1SDA/PA10 I2C0SCL/PA9 I2C0SDA/PA8 RX1/PB4 TX1/PB5 RTS1/PB6 CTS1/PB7 LDO VDD VSS VBUS VDD33 DD+ PB0/RX0 PB1/TX0 PB2/RTS0 PB3/CTS0 PC3/SDO00 PC2/SDI00 PC1/SPCLK0 PC0/SS00 PE5 PB11/TM3 PB10/SS01/TM2 PB9/SS11/TM1 GREEN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ICE_DAT ICE_CLK ICE_DAT ICE_CK C/C,1uF ICECHIP1 100K DDAT DCLK DRST DH1 CC85 R27 CC32 T/C,10uF/10V C/C,0.1uF CC33 CT9 BAT2 C/C,0.1uF T/C,22uF/10V AA BATTERY BOX Title NUC100/ICE Parts Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 4 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 45 of 60 User Manual NuMicro Family /// NANO130 GPIO /// CTK[6..7] CTK[11..15] PB8 PE6 PE14 PE15 PA12 ADC[0..4] I2C0SDA I2C0SCL CKT[6..7] CKT[11..15] VCC_P GPIO x 5 ADC[0..4] ADC x 5 I2C0SDA I2C0SCL VCC_P Touch x 7 PB8 PE6 PE14 PE15 PA12 VCC_P VCC_P JR1 nWE/SEG22 AD0/SEG24 SEG27 AD3/SEG33 AD5/DAC1 AD7/SEG37 1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19 JR2 2 4 6 8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20 nRE/SEG23 AD1/SEG25 AD2/SEG32 AD4/DAC0 AD6/SEG36 AD8/SEG38 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 SEG19 SEG17 SEG15 ALE/SEG11 SEG9 SEG3 SEG1 COM3 COM1 CONN RECT 10x2 I2C x 1 GND GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 SEG18 SEG16 SEG14 nCS/SEG10 SEG8 SEG2 SEG0 COM2 COM0 VCC_P J5 I2S_MCLK I2S_LRC I2S_BCLK I2S_DACDATA I2S_ADCDATA SC1_CLK SC1_DAT SC1_PWR SC1_RST SC1_PRES ICE_DAT ICE_CK MCU_STATUS MPU LCM+LCD SPI x 2 JP1 SC1_PRES SC1_PRES/I2S_DIN I2S_DIN SPI0CLK SPI1CLK 1 2 3 3PX1 PWM1_0 PWM x 1 I2S_MCLK SC1_PWR/I2S_WS SC1_RST/I2S_BCLK I2S_DOUT I2S_DIN I2S x 1 SC1_CLK SC1_DAT SC1_PWR/I2S_WS SC1_RST/I2S_BCLK SC1_PRES GND nINT x 2 T10 TPAD T11 TPAD T12 TPAD T13 TPAD T14 TPAD SMC x 1 1 PWM1_0 GND 1 SPI0CLK SPI1CLK SPISS00 SPISS10 SPIMISO00 SPIMISO10 SPIMOSI00 SPIMOSI10 UART x 2 1 SPISS00 SPISS10 SPIMISO00 SPIMISO10 SPIMOSI00 SPIMOSI10 nINT[0..1] CONN RECT 15x2 1 nINT[0..1] TXD[0..1] RXD[0..1] 1 TXD[0..1] RXD[0..1] ICE_DAT V1 ICE_CK V2 V3 PE5 CC80 CC81 CC82 C/C,0.1uF C/C,0.1uF C/C,0.1uF CC83 C/C,0.1uF GND GND T15 DAC0 T16 DAC1 GND 1 AD4/DAC0 1 AD5/DAC1 ADC0 ADC1 ADC2 ADC3 ADC4 AD8/SEG38 AD7/SEG37 AD6/SEG36 I2C0SDA I2C0SCL nWE/SEG22 nRE/SEG23 PA12 CTK11 RXD0 TXD0 89 90 91 92 93 94 95 96 12 11 10 9 79 78 77 76 SPIMOSI10 SPIMISO10 SPI1CLK SPISS10 RXD1 TXD1 ALE/SEG11 nCS/SEG10 PB8 V1 V2 V3 AD0/SEG24 AD1/SEG25 nINT0 nINT1 44 45 46 47 19 20 21 22 126 64 63 62 4 3 2 111 DH1 DH2 COM0 COM1 COM2 COM3 AD4/DAC0 AD5/DAC1 CTK12 CTK13 CTK14 CTK15 PWM1_0 PC13 AD2/SEG32 AD3/SEG33 57 56 55 54 53 52 108 107 75 74 73 72 71 70 110 109 MPU LCM+LCD U5B PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PA8 PA9 PA10 PA11 PA12 PA13 PA14 PA15 PD0 PD1 PD2 PD3 PD4 PD5 PD6 PD7 PD8 PD9 PD10 PD11 PD12 PD13 PD14 PD15 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 PB10 PB11 PB12 PB13 PB14 PB15 PE0 PE1 PE2 PE3 PE4 PE5 PE6 PE7 PE8 PE9 PE10 PE11 PE12 PE13 PE14 PE15 PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 PC8 PC9 PC10 PC11 PC12 PC13 PC14 PC15 PF4 PF5 100 101 102 103 105 106 48 49 13 14 15 16 17 18 50 51 SC1_CLK SC1_DAT SC1_PWR/I2S_WS SC1_RST/I2S_BCLK SC1_PRES/I2S_DIN I2S_DOUT SEG3 SEG2 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG1 SEG0 69 68 67 66 65 61 58 38 37 36 35 34 33 1 128 127 I2S_MCLK SPISS00 SPI0CLK SPIMISO00 SPIMOSI00 PE5 PE6 SEG8 SEG9 PE9 PE10 PE11 PE12 SEG27 PE14 PE15 122 123 CTK6 CTK7 PB1 PB3 PD7 PD15 PC4 PC2 PE4 PE2 PE0 PC12 PA14 PA12 PF1 SPIMISO10 SPISS10 SEG2 SEG0 COM2 COM0 SPIMOSI00 SPI0CLK I2S_MCLK PWM1_0 RXD0 PA12 ICE_CK PA1 PA3 PA5 PA7 PD1 ADC1 ADC3 AD8/SEG38 AD6/SEG36 SC1_DAT VCC_P 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 SPIMOSI10PB0 SPI1CLK PB2 SEG3 PD6 SEG1 PD14 COM3 PC5 COM1 PC3 PE6 PE6 PE5 PE5 SPIMISO00PE3 SPISS00 PE1 PC13 PC13 TXD0 PA15 ICE_DAT PF0 ADC0 PA0 ADC2 PA2 ADC4 PA4 AD7/SEG37PA6 SC1_CLK PD0 CONN RECT 20x2 GND J4 PE8 PE10 PE12 PB6 PB4 PD12 PD10 PD8 PA9 PA11 PB13 PE13 PE15 PB15 PC15 PC7 PD4 PD2 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 nINT1 33 AD3/SEG33 35 AD5 37 SC1_PRES/I2S_DIN SC1_PWR/I2S_WS39 SEG9 PE10 PE12 ALE/SEG11 RXD1 SEG15 SEG17 SEG19 I2C0SCL nRE/SEG23 AD1/SEG25 SEG27 PE15 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 SEG8 PE7 PE9 PE9 PE11 PE11 nCS/SEG10PB7 TXD1 PB5 SEG14 PD13 SEG16 PD11 SEG18 PD9 I2C0SDA PA8 nWE/SEG22PA10 AD0/SEG24PB12 nINT0 PB14 PE14 PE14 PB8 PB8 AD2/SEG32PC14 AD4 PC6 I2S_DOUT PD5 SC1_RST/I2S_BCLK PD3 CONN RECT 20x2 GND NANO130_24 Title NANO130/GPIO Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 5 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 46 of 60 User Manual NuMicro Family /// Current Sense Parts /// I2C0SDA I2C0SCL MCU_STATUS 3 a b c d e f g dot P SSD2 7-SEG_a 7 7-SEG_b 6 7-SEG_c 4 7-SEG_d 2 7-SEG_e 1 7-SEG_f 9 7-SEG_g 10 7-SEG_dot 5 8 a f b g e c COM 3 d R59 CC70 1 b g e c COM 3 d R60 TOS5101BH 33 2N3904 Q3 1 TOS5101BH 33 1 ISEN_INT b g SP2 e COM c SW d TOS5101BH 2N3904 Q5 R57 1.2K ISEN_X12MO a f GND 3 Scan1 3.3V 3 Scan2 C/C,20pF a b c d e f g dot P R61 2N3904 Q4 3 R56 1.2K 12MHz CC71 f 2 R55 1.2K Scan0 X4 SSD3 7 7-SEG_a 6 7-SEG_b 4 7-SEG_c 2 7-SEG_d 1 7-SEG_e 9 7-SEG_f 10 7-SEG_g 7-SEG_dot 5 8 a 2 33 ISEN_X12MI C/C,20pF a b c d e f g dot P 2 I2C0SDA I2C0SCL MCU_STATUS SSD1 7-SEG_a 7 7-SEG_b 6 7-SEG_c 4 7-SEG_d 2 7-SEG_e 1 7-SEG_f 9 7-SEG_g 10 7-SEG_dot 5 8 LED4 3.3V 1 LED_mA 2 GND R64 220 GREEN_LED LED5 3.3V HEADER 5 1 2 3 4 5 1 CT15 CC72 T/C,10uF/10V C/C,1uF V_SENS+ VBAT R4 ISEN_DAT ISEN_CK ISEN_RST R65 LED_uA 2 220 GREEN_LED LED6 1 DNE LED_PD 2 R51 R53 1 1% U12 1 2 3 ISEN_IDD GND RS+ GND OUT RS- 4 VBAT ISEN_IDD ISEN_VDD CC78 R63 C/C,0.1uF ISEN_INT ISEN_X12MO ISEN_X12MI 100K GND ISEN_MODE 37 38 39 40 41 42 43 44 45 46 47 48 ADC5/PA5 ADC6/PA6 ADC7/SS21/PA7 AVDD PC7 PC6 PB15 PF2/XT1_OUT PF3/XT1_IN /RESET PVSS PB8 GREEN_LED Gate 6 5 2 1 Source 3 FDC606P (P-FET) Drain ISEN_MODE ADC4/PA4 ADC3/PA3 ADC2/PA2 ADC1/PA1 ADC0/PA0 AVSS PF1/ICE_CK PF0/ICE_DAT PA12 PA13 PA14 PA15 GND ISEN_RST 3.3V U13 R52 100 1% U14 36 35 34 33 32 31 30 29 28 27 26 25 CC89 3.3V 220 5 MAX9938FH C/C,0.1uF R66 100K 4 ISEN_CK ISEN_DAT GND LED_MA LED_uA LED_PD DH3 V_SENS- ISEN_IDD CC77 PB9 PB10 PB11 PE5 PC0 PC1 PC2 PC3 PB3 PB2 PB1 PB0 NANO100 LQFP 48 24 23 22 21 20 19 18 17 16 15 14 13 C/C,0.1uF 7-SEG_a 7-SEG_b 7-SEG_c 7-SEG_d 7-SEG_e 7-SEG_f 7-SEG_g 7-SEG_dot Current Sense block GND Scan2 Scan1 Scan0 PB12 X32O X32I PA11 PA10 PA9 PA8 PB4 PB5 LDO VDD VSS CC73 C/C,1uF 3.3V 1 2 3 4 5 6 7 8 9 10 11 12 3.3V GND GND CC79 MCU_STATUS I2C0SCL I2C0SDA CC74 CC75 Title C/C,0.1uF GND C/C,1uF GNDGND C/C,1uF GND NANO100/Current Sense Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 5 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 47 of 60 User Manual NuMicro Family /// NANO130 MISC. /// ICE_DAT ICE_DAT ICE_CK ICE_CK VCC_MCU AVCC_MCU U5A 27 83 120 ICE_RST ICE_RST VDD VDD VDD AVDD Vref 99 97 CC34 X12MI 113 USB5.0V XT1_In/PF3 C/C,20pF VBUS X2 USB Device 40 CC63 12MHz CC36 X12MO 114 C/C,1uF GND USB_DUSB_D+ CC37 6 X32KO 1 XT1_Out/PF2 C/C,20pF 42 R36 GND 43 27 USB_D- 2 USB_D+ 3 R37 X32O 4 27 CC38 CC39 TBD TBD 5 C/C,6pF X3 J10 CC40 HEADER 2 32.768KHz ICE_DAT/PF0 7 2 1 X32KI ICE_RST X32I ICE_CK/PF1 ICE_DAT 81 ICE_CK GND 116 nRESET VCC 87 88 R38 125 29 30 31 32 85 86 117 118 124 100K BP1 CC41 SW C/C,1uF ADC_GND GND DD+ ID GND Shield Shield Shield Shield 6 7 8 9 GND /RESET AVSS AVSS USB_VDD33_CAP PVSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VLCD LDO 41 59 HEADER 5 24 1 2 3 4 5 NANO130_24 GND GND CC76 Operating voltage: 1.8V~3.6V J8 VBUS USB MINI-B RECEP. 80 C/C,6pF GND CON2 C/C,1uF CC88 C/C,1uF CC84 C/C,1uF ICE_DAT ICE_CK ICE_RST DH2 GND GND VCC GND GND HEADER 2 VCC_MCU 2 1 VCC CC45 C/C,0.1uF GND AVCC_MCU FB3 FB CC46 CC47 C/C,4.7uF C/C,0.1uF C/C,0.1uF C/C,0.1uFFB4 FB CC48 CC49 CC50 CC51 C/C,1uF C/C,0.1uF ADC_GND Title V_SENS_+ V_SENS- NANO130/MISC. Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 6 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 48 of 60 User Manual NuMicro Family /// Power parts /// Power Good indicator DVBUS ICE Power LED2 R39 330 VCC GREEN_LED GND USB5.0V Power CON 3 1 2 CON3 U6 RT9164A-3.3v OUT 3.3V/1A LDO SS24A IN GND OUT D1 4 USB_BUS Power VDD5.0V 5V Power Adpater VDD3.3V 1 GND VCC VCC_P VDD3.3V JP2 CC52 CT10 CT11 CC53 C/C,0.1uF T/C,10uF/10V T/C,10uF/10V C/C,0.1uF CC54 CT12 1 2 3 2 3 GND IN C/C,0.1uF T/C,22uF/10V 3PX1 GND GND GND VBAT OFF:1-3 ON:2-3 3 MAIN POWER VCC SW_POWER1 1 2 6 4 CT13 5 T/C,10uF/10V SW DPDT/SM Switch power source form BATTERY to LDO(3.3V) when system power ON. T4 TPAD T5 TPAD T6 TPAD 1 1 1 1 1 T7 TPAD T8 TPAD T9 TPAD 1 T3 TPAD 1 T2 TPAD 1 T1 TPAD 1 Testing Pad VDD3.3V VCC VBAT Title GND GND Power Parts Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 7 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 49 of 60 User Manual NuMicro Family /// SMC & SD & FLASH /// VCC_P SC1_CLK SC1_DAT SC1_PWR SC1_RST SC1_PRES SC1_CLK SC1_DAT SC1_PWR SC1_RST SC1_PRES CC64 R68 R69 100K SMC1(Smart Card) VCC_P C/C,0.1uF 100K 1 R41 VCC_SMC Si2301ADS 100K VCC_SMC Q8 3 SPISS00 SPISS10 SPIMISO00 SPIMISO10 SPIMOSI00 SPIMOSI10 2 GND SPISS00 SPISS10 SPIMISO00 SPIMISO10 SPIMOSI00 SPIMOSI10 CC61 SPI0CLK SPI1CLK SPI0CLK SPI1CLK CC62 Q7 Si2302ADS SC1_PWR R42 R43 10K C/C,0.1uF SC1_PRES 10K SD_PWR_ON PE6 GND GND SD_INT SD_CTL PE15 PE14 10 9 C/C,1uF GND SC1_CLK SC1_RST R67 200K CLK RST VCC_SMC C4 C3 C2 C1 P1 R44 S2 S1 10K C4 C3 C2 C1 C8 C7 C6 C5 C8 C7 C6 C5 DAT SM Card Slot SD_CD nINT0 SC1_DAT GND GND SPI1(SPI-SD) SD_VCC VCC_P 33 Si2301ADS Q2 FB7 FB 1 R46 CC65 CC66 HOLD SOT-23 D CC67 GND WP RSV DO VSS CLK VDD VSS DI CS RSV C/C,0.1uF C/C,1uF C/C,0.1uF G 3 2 S HOLD 1 14 (Top View ) C/C,1uF SPI0(SPI-Flash) GND CD# GND LED3 J7 15 Drain CC42 SD_VCC (P-FET) 3 R45 2 1 Gate SD_VCC 8 7 6 5 8P4R-4.7K RP2 Source SD_PWR_ON 1 2 3 4 SPISS10 SPI1CLK SPIMISO10 SPIMOSI10 2 VCC_P GREEN_LED 11 10 GND SD_CTL SPIMISO10 SPISS00 SPIMISO00 SPI1CLK R49 SPIMOSI10 SPISS10 SD_INT 22 CC69 10K 1 2 3 4 U10 CS DO WP GND SPI-FLASH VCC HOLD CLK DI 8 7 6 5 VCC_P SPI0CLK SPIMOSI00 W25Q16CL TBD C/C,0.1uF GND 12 13 SD_CD GND CC68 VCC GND R50 FB9 R48 VCC_P R47 10K 8 7 6 5 4 3 2 1 9 100K SD/MMC SOCKET GND VCC_P 220 Operating voltage: 3.1V~3.6V GND Operating voltage: W25XxxBL=2.3V~3.6V W25XxxL=3.0V~3.6V (VIH:0.7Vcc/VIL:0.3Vcc) FB Title GND SD & SMC & Flash Size B Document Number <Doc> Date: Wednesday , September 05, 2012 Rev 1.1 Sheet 9 of 10 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 50 of 60 User Manual NuMicro Family /// LCM /// VCC VCC JR1 SEG19 SEG17 SEG15 ALE/SEG11 SEG9 SEG3 SEG1 COM3 COM1 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 VCC CON1 SEG18 SEG16 SEG14 nCS/SEG10 SEG8 SEG2 SEG0 COM2 COM0 nCS/SEG10 ALE/SEG11 nWE/SEG22 nRE/SEG23 CONN RECT 15x2 GND GND VCC VCC VCC JR2 nWE/SEG22 AD0/SEG24 SEG27 AD3/SEG33 AD5 AD7/SEG37 1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19 2 4 6 8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20 nRE/SEG23 AD1/SEG25 AD2/SEG32 AD4 AD6/SEG36 AD8/SEG38 R1 10K SEG19 SEG27 AD0/SEG24 AD1/SEG25 AD2/SEG32 AD3/SEG33 AD4 AD5 AD6/SEG36 AD7/SEG37 LCD_RST FMARK CC1 IM3 C/C,1uF CONN RECT 10x2 GND BL_A GND GND VCC BL_K BL_A IM3 80 Mode 9-bit Pull-Low 80 Mode 8-bit NC NC NC NC GND CS RS WR RD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 DB16 DB17 RESET FMARK IM0 IM3 IOVCC VCC A1 A2 A3 A4 PWM K VCC CC2 C/C,1uF GND VCC CC3 C/C,1uF FPC 1X39 GFT024CA240320 Mode Pull-High 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 GND GND IM3 R3 10K Title BL_K LCM Size A Document Number <Doc> Date: Wednesday , July 27, 2011 Rev A GND Sheet 1 of 1 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 51 of 60 User Manual NuMicro Family SEG19 SEG17 SEG15 ALE/SEG11 SEG9 SEG3 SEG1 COM3 COM1 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 SEG18 SEG16 SEG14 nCS/SEG10 SEG8 SEG2 SEG0 COM2 COM0 SEG3 SEG2 SEG1 SEG0 AD3/SEG33 AD2/SEG32 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 COM3 COM2 COM1 COM0 JR1 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 AD8/SEG38 SEG27 VCC U1 LCD 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 VCC AD6/SEG36 AD7/SEG37 /// LCD /// CONN RECT 15x2 GND GND VCC VCC 1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19 2 4 6 8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20 nRE/SEG23 AD1/SEG25 AD2/SEG32 AD4 AD6/SEG36 AD8/SEG38 SEG8 SEG9 nCS/SEG10 ALE/SEG11 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 nWE/SEG22 nRE/SEG23 AD0/SEG24 AD1/SEG25 nWE/SEG22 AD0/SEG24 SEG27 AD3/SEG33 AD5 AD7/SEG37 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 JR2 CONN RECT 10x2 GND GND Title LCD Size A Document Number <Doc> Date: Monday , April 18, 2011 Rev A Sheet 1 of 1 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 52 of 60 User Manual NuMicro Family 4 BOM List Nu-LB-Nano130 Board BOM List: NANO130 Revised: Wednesday, September 05, 2012 Bill Of Materials December 17, 2012 Item Quantity Reference 9:54:05 Revision: 1.1 Page1 Part ______________________________________________ 1 1 BAT2 AA BATTERY BOX 2 3 SP1,BP1,SP2 SW 3 4 IDLE1,ICP1,ICE1,BUSY1 4 1 BU1 Buzzer 5 33 CC2,CC3,CC5,CC19,CC20, C/C,0.1uF KPT-2012 CC24,CC25,CC32,CC33,CC45, CC47,CC48,CC49,CC51,CC52, CC53,CC54,CC56,CC60,CC62, CC64,CC65,CC67,CC68,CC77, CC78,CC79,CC80,CC81,CC82, CC83,CC87,CC89 6 1 CC4 C/C,0.01uF 7 25 CC6,CC8,CC10,CC13,CC29, C/C,1uF CC30,CC41,CC42,CC50,CC55, CC57,CC58,CC59,CC61,CC63, CC66,CC72,CC73,CC74,CC75, CC76,CC84,CC85,CC86,CC88 8 2 CC7,CC9 C/C,220pF 9 4 CC11,CC12,CC14,CC15 10 1 CC16 11 7 CC17,CC18,CC21,CC22,CC23, C/C,TBD C/C,100pF C/C,4.7uF CC26,CC46 12 9 CC27,CC28,CC34,CC36,CC37, C/C,20pF CC40,CC70,CC71,CC99 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 53 of 60 User Manual NuMicro Family 13 3 CC38,CC39,CC69 TBD 14 1 CON2 USB MINI-B RECEP. 15 1 CON3 Power CON 16 1 CON4 DB9_MALE 17 2 CT1,CT2 T/C,100uF 18 6 CT3,CT8,CT10,CT11,CT13, T/C,10uF/10V CT15 19 4 CT4,CT5,CT9,CT12 T/C,22uF/10V 20 3 DH1,DH2,DH3 21 2 D1,D6 22 8 FB1,FB3,FB4,FB5,FB6,FB7, FB HEADER 5 SS24A FB8,FB9 23 1 ICECHIP1 NUC120 LQFP 64 24 1 ICE_USB1 mini USB 5pin 25 2 JP1,JP2 3PX1 26 1 JR1 CONN RECT 10x2 27 1 JR2 CONN RECT 15x2 28 2 J1,J2 PJK-634 29 2 J3,J6 2PX1 30 2 J4,J5 CONN RECT 20x2 31 1 J7 32 2 J8,J10 HEADER 2 33 2 K1,K2 CTKey 34 1 K3 CTKey_SLIDER 35 6 LED1,LED2,LED3,LED4,LED5, GREEN_LED SD/MMC SOCKET LED6 36 2 MIC1,MIC2 TP 37 17 NTC1,R2,R11,R14,R25,R26, 100K R27,R28,R29,R31,R38,R41, R50,R53,R63,R68,R69 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 54 of 60 User Manual NuMicro Family 38 1 P1 SM Card Slot 39 4 Q1,Q3,Q4,Q5 2N3904 40 2 Q2,Q8 41 1 Q7 Si2302ADS 42 1 RP1 8P4R-330 43 1 RP2 8P4R-4.7K 44 1 R4 DNE 45 3 R5,R23,R30 46 1 R6 100 47 4 R7,R8,R17,R18 48 3 R9,R10,R49 49 4 R12,R13,R15,R16 5.6K 50 1 R19 47K 51 2 R20,R32 1K 52 5 R21,R46,R64,R65,R66 220 53 1 R22 12K 54 4 R33,R34,R36,R37 27 55 1 R39 330 56 6 R40,R42,R43,R44,R47,R48 10K 57 5 R45,R59,R60,R61,R99 33 58 1 R51 1 1% 59 1 R52 100 1% 60 3 R55,R56,R57 1.2K 61 1 R67 200K 62 3 SSD1,SSD2,SSD3 TOS5101BH 63 1 SW_POWER1 64 14 T1,T2,T3,T4,T5,T6,T7,T8, Si2301ADS 0 2.2K 22 SW DPDT/SM TPAD T9,T10,T11,T12,T13,T14 65 1 T15 DAC0 66 1 T16 DAC1 © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 55 of 60 User Manual NuMicro Family 67 1 U2 24LC64 68 1 U3 WAU8822 69 2 U4,U6 70 1 U5 NANO130_24 71 1 U7 SP3232ECN 72 1 U8 HSDL-3201 73 1 U10 W25Q16CL 74 1 U12 MAX9938FH 75 1 U13 FDC606P 76 1 U14 NANO100 LQFP 48 77 1 VR1 50K 78 3 X1,X2,X4 79 1 X3 32.768KHz RT9164A-3.3v 12MHz © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 56 of 60 User Manual NuMicro Family LCD Glass Module Board BOM List: LCD Revised: Tuesday, August 23, 2011 Revision: A Bill Of Materials September 2,2011 Item Quantity Reference 15:04:49 Page1 Part ______________________________________________ 1 1 JR1 CONN RECT 15x2 2 1 JR2 CONN RECT 10x2 3 1 U1 LCD © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 57 of 60 User Manual NuMicro Family Color LCM Board BOM List: LCM Revised: Wednesday, July 27, 2011 Revision: A Bill Of Materials October 4,2012 Item Quantity Reference 10:43:19 Page1 Part ______________________________________________ 1 3 CC1,CC2,CC3 C/C,1uF 2 1 CON1 3 1 JR1 CONN RECT 15x2 4 1 JR2 CONN RECT 10x2 5 2 R3,R1 FPC 1X39 10K © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 58 of 60 User Manual NuMicro Family Revision History Rev. Date Description 1.00 11-09-2012 Initially issued. 1.01 12-17-2012 Modified the schematics and the BOM list of Nu-LB-Nano130. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 59 of 60 User Manual NuMicro Family Important Notice Nuvoton products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Furthermore, Nuvoton products are not intended for applications wherein failure of Nuvoton products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Nuvoton customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Nuvoton for any damages resulting from such improper use or sales. Please note that all data and specifications are subject to change without notice. All the trademarks of products and companies mentioned in this datasheet belong to their respective owners. © 2012 Nuvoton Technology Corp. User Manual Rev. 1.01 — Dec 17, 2012 60 of 60