Ionpure® LabXT Laboratory Electrodeionization (CEDI) Modules

Ionpure® LabXT Laboratory
Electrodeionization (CEDI) Modules
The LabXT module is designed with proven Ionpure® continuous
electrodeionization (CEDI) technology to produce laboratory grade
high purity water. These CEDI modules provide a reliable and cost
effective replacement option for Millipore’s Elix® module equipped
Laboratory Water Systems. Expand your laboratory component and
service related capabilities with proven Ionpure® CEDI technologies.
Each LabXT module is designed specifically for the flow rate and
water quality requirements of the following Elix® systems.
Millipore Elix®
System
Ionpure® LabXT Replacement
Module
Module
Flow Rate
Elix 3
IP-LabXT 3
3 l/h
Elix 5
IP-LabXT 5
5 l/h
Elix 10
IP-LabXT 10
10 l/h
LabXT Series Features
Low extractable natural polysulfone construction
Packaged and assembled with connections and wiring for direct
Elix® module replacement
Guaranteed leak free operation
Proven performance from the worldwide leaders in
electrodeionization technologies
Effective 4-pass flow design
ANODE END
3 LPH
ANODE END
5 & 10 LPH
.88 22.2 TYP
BLOCKED
BLOCKED
CATHODE END
3, 5 & 10 LPH
"A"
.59 15
6 MM X 6 MM
TUBE FITTING TYP
1.87 47.5
MOUNTING HOLE
BLOCKED
CONC. FEED IN
BLOCKED
WASTE OUT
M4-.7 X 8 NEGATIVE
TERMINAL SCREW
6.45 163.8
M4-.7 X 8 POSITIVE
TERMINAL SCREW
6.20 157.5
10.88 276.2
13.00 330.2
12.75 323.8
5.08 129.1
CONC. FEED IN
DILUTE FEED IN
BLOCKED
DILUTE FEED IN
BLOCKED
.65 16.6
PRODUCT OUT
TYP
.31 7.9
.59 15
CL
CL
1.85 47.1
CL
"B"
"C"
2.23 56.6
.88 22.4
Ionpure® LabXT Laboratory Electrodeionization (CEDI) Modules
Operating Environment
Installation should be indoors with no direct
sunlight and it should have a maximum ambient
room temperature of 113°F (45°C).
Materials Construction
Wetted components of the LabXT module
consist of: natural polysufone, ion-selective
membranes, ion exchange resins, and
thermoplastic elastomer.
Quality Assurance Standards
Each module is factory tested to meet strict
Ionpure module and industry standards and
is manufactured in an ISO 9001:2000
facility. The final assembled modules are
factory tested to ensure interconnector and
electrical integrity.
Ordering Info
CEDI Feed Water Specifications*
Water Quality
RO Permeate
CEDI Feed Water Conductivity
<60 µS/cm
CO2
<30 ppm as CO2
Temperature
5-35 ºC
Total Chlorine
<0.02 ppm as Cl2
Inlet Pressure
0.5 – 1.5 bar
TOC
500 ppb as C
* At inlet to CEDI module
CEDI Performance**
Recovery
60%
Flow Rate (LabXT 3, 5 and 10)
3 l/h , 5 l/h and 10 l/h
Product Resistivity
>5 MΩ-cm (10-15 MΩ typical)
1. Part number to use when ordering:
LabXT 3 lph
W3T101571
TOC (with RO pretreatment)
< 30 ppb
LabXT 5 lph
W3T101572
Silica (SiO2)
> 99.9% removal
LabXT 10 lph
W3T101573
** When installed in Millipore ELIX® system
2. Each LabXT module has compatible water
connections to allow for simple replacement.
Physical Specifications
Dimensions
in (mm)
6 mm tubing connections
Weight
lb (kg)
Module
3. Module electrical power connections are
made through the included wiring harness.
Siemens
10 Technology Drive
Lowell, MA 01851
Phone: 866.876.3340
Depth
(Includes elbows)
Width
LabXT 3
4.08 (103.6)
2.23 (56.6)
2.3 (1.04)
LabXT 5
4.58 (116.3)
2.23 (56.6)
2.8 (1.27)
LabXT 10
5.08 (129.0)
2.23 (56.6)
3.3 (1.50)
© 2010 Siemens Water Technologies Corp.
ION-LABXT-DS-0310
Subject to change without prior notice.
Ionpure is a trademark of Siemens its subsidiaries or affiliates.
Elix is a trademark of Millipore Corporation.
The information provided in this brochure contains merely general
descriptions or characteristics of performance which in actual case
of use do not always apply as described or which may change as a
result of further development of the products. An obligation to
provide the respective characteristics shall only exist if expressly
agreed in the terms of contract.
www.siemens.com/ionpure