MAGNUM-SALT SPREADER REVISION FINAL for

RECEIVER MOUNT
Weight capacity:
Cubic capacity:
Hopper material:
Empty weight of unit:
Mounting method:
Dimensions:
S575RP
TM
350 pounds
5.75 cu. ft.
304 Stainless Steel or Polyethylene
SS-130 pounds, poly 120 pounds
Hitch, 2 inch receiver, no drilling required
SS h 33 in., w 49 in., d 30 in.
Poly-h 35.5 in., W 49 in., d 30 in.
SALT/ SAND
Standard equipment:
·Wiring harness
·Variable speed controller with on/off and burst positions
·Cover matches hopper material
·Standard mounting hardware
THREE POINT MOUNT ADAPTER
SSTPT
Three point tractor adapter (SSTPT)
Weight capacity:
Accessory weight:
Mounting method:
Accessory dimensions:
Construction:
500 pounds
32 pounds
Uses three-point tractor accessory
connections to provide mount for
standard S575RP
h 17.5 in., w 10.5 in., d 32 in.
Black painted steel, .25 thick
FLATBED UTILITY ADAPTER
S100009
Flatbed utility mount adapter (S100009)
500 pounds
18 pounds
Bolts to any flat surface to provide a
sturdy mounting point for S575R.
Requires drilling of flatbed to accept
mounting bolts (not included).
Accessory dimensions: h 2.5 in., w 16 in., d 16 in.
Construction:
Powder-coated steel, .25 thick
Weight capacity:
Accessory weight:
Mounting method:
ACCESSORIES
SSHS
SSDK
SSHS
Hopper screen
SSDK
Receiver Mount Docking station
S500001
Flow gate assembly
S200057* Baffle plate
SSHV*
Vibrator
S200062* Extended Auger
* Sander conversion parts
S200062*
S500001
SSHV*
S200057*
TM
SPREADERS
TM
At the heart of all MAGNUM spreaders is our direct drive auger/impeller.
There's no gear drive to rob power from where it's needed and no drive
lubricant to turn to molasses in extreme cold. No gears, no lubricant, you
get75% more a u ger power, the strongest on the market!
S1075P with DUMP TRUCK MOUNT
S100011
750 pounds
10.75 cu. ft.
304 Stainless Steel or Polyethylene
SS-215 pounds, poly 200 pounds
Upper portion straddles tail gate and is held in
place with set screws front and back. Lower portion
of frame fits two 'L' shape adjustable brackets
to truck frame rails for secure attachment.
Overall dimensions: h 49 in., w 54 in., d 43 in.
Weight capacity:
Cubic capacity:
Hopper material:
Empty weight of unit:
Mounting method:
Standard equipment:
·Wiring harness
·Variable speed controller with on/off and burst positions
·Cover matches hopper material
·Standard mounting hardware
Motor Features
1. All frame components powder coated
2. 304 stainless steel spinner
3. Motor lead location prevents accidental damage from below
4. Low loss electrical harness
5. Watertight connectors
6. Stainless steel shaft
7. Motor protected with sealed frame, special shaft seal
S1075P with FIXED MOUNT
Weight capacity:
Cubic capacity:
Hopper material:
Empty weight of unit:
Mounting method:
Dimensions:
and designed with press fitted double ball bearings
8. Variable speed control
2
Design Features
Seven mounting methods
Hoppers available in stainless steel or polyethylene
Fewer moving parts
Designed by motor experts
Two-year warranty (Parts only)
Motor dimensions: Height-7 inches; Diameter-6.6 inches
Our controller delivers 40 amperes continuously and surges
70 amperes for up to three seconds. These units spread
rock salt, calcium chloride and other ice melting materials in
a spread pattern more than 40 feet across.
S300000
750 pounds
10.75 cu. ft.
304 Stainless Steel or Polyethylene
SS-175 pounds, Poly-160 pounds
Fixed. Requires drilling of top section of pickup
sides and bumper. No access to bed through tailgate.
SS-h 41.2 in., w 53.6 in., d 25 in.
Poly h 44.5 in., W 53.6 in, d 25 in.
Standard equipment:
·Wiring harness
·Variable speed controller with on/off and burst positions
·Cover matches hopper material
·Standard mounting hardware
5
1
3
4
6
7
S1075P with HINGED MOUNT
Weight capacity:
750 pounds
Cubic capacity:
10.75 cu.ft.
Hopper material:
304 stainless steel or Polyethylene
Empty weight of unit: SS-175 pounds, Poly 160 pounds
Mounting method:
Mounts to pickup bed and bumper; drilling required
for bumper. Allows access to pickup bed by hinging
to the side.
Dimensions:
SS-h 41.2 in., adjustable, d 25 in.
Poly-h 44.5in., adjustable, d 25 in.
Standard equipment:
·Wiring harness
·Variable speed controller with on/off and burst positions
·Cover matches hopper material
·Mounting hardware
S1075M with FLATBED MOUNT
8
S400000
Weight capacity:
Cubic capacity:
Hopper material:
Empty weight of unit:
Mounting method:
S100010
750 pounds
10.75 cu. ft.
304 Stainless Steel or Polyethylene
SS-220 pounds,Poly 205 pounds
Mounting method:Triangulated support frame
mounts to flatbed surface. Requires drilling of
flatbed to accept mounting bolts (not included).
h 49 in., w 54 in., d 43 in.
Overall dimensions:
Standard equipment:
·Wiring harness
·Variable speed controller with on/off and burst positions
·Cover matches hopper material
·Standard mounting hardware