Veg Fiber

Transcription

Veg Fiber
FIBREFLEXPACKING 8r MFG. CO.
INCORPORATED
P.O. BOX 4646, PHILADELPHIA,PA 19127
·
·
·
FIBREFLEX
Vegetable Fibre Sheet
OFFICE and PLANT
5101 Umbria Street
PHI LA., PA. 19128
THIO.FLEX
Thiokol Coated Fibreflex
FIBRE.KORK @
Fibre-Cork Composition
TELEPHONES
(215) 482-1604
(215) 482-1490-91
Fax: (215) 487-1220
GASKET SERVICE LISTING*
MAXIMUM TEMPERATURE LIMITATION2500
FIBREFLEXmaterials are tough, pliable and compressible Protein Binder-treated fibre sheet packing
used for flange gaskets in sealing fluidsor gases as listed below. Fibreflexmaterials are glycerine treated,
whichpreventsflangeadhesionand corrosion.
*Fibreflexmakesno expressor impliedrecommendationsfor use of its materials.This list is offeredonly
as a guide and we stronglyrecommendtestingbe performedin yourapplicationpriorto approval.
Acetone
Alcohol
Aninal Fats & Oils
Benzene (Benzol)
Benzine (Gasoline)
Bunker Oil
Butane
Butyl Acetate
Carbon Dioxide
Carbon Tetrachloride
Chlorinated Solvents
Cresol
Detergents
Dibutyl Phthalate
DOP (Dioctyl Phthalate)
Dry Cleaning Fluid
Ether
Ethyl Acetate
Ethylene Glycol
Formaldehyde
Fuel Oil
Gas Illuminating
Gasoline
Gylcerine
Greases
Hydrogen
Hydrogen Sulphide
Inerteen 70-30
Inks
Kerosene
Lacquers and Thinners
Linseed Oil
Lubricating Oil
Methyl Choride (Refrigerant)
Methyl Isobutyl Detone (MIBK)
Naphtha, Petroleum
Naphtha, Coal Tar
Paints
Petroleum
Phenol
Prestone (Antifreeze)
Propylene Glycol
Pyranol A13B3B
Skydrol 500B
Skydrol 7000B
Soap
Sperry Oil
Super VM&PNaphtha
Toluol
Transformer Oil
Trichloroethylene
Tricresyl Phosphate
Triethylene Glycol (Neutral Grade)
Turpentine
Varnish
Vegetable Oil
Water
Wood Alcohol
Xylol
The use of FIBREFLEX materials in sealing the following is UNSATISFACTORY and is NOT recommened:
Acids (Inorganic)
Alkalies
Ammonia
Hydrochloric Acid
Freon 12 & 22
Nitric Acid (Dilute)
Nitro Benzine
Oxygen
Silicate of Soda
Suphuric Acid (Dilute)
Steam
NOTE: In order to prevent possible dimensional instability, it is recommened that gaskets and other cut
parts be protected from wide changes in humidity and temperature.
----
FIBREFLEXPACKING & MFG. CO.
INCORPORATED
·
Vegetable Fibre Sheet
· Thiokol
Coated Fibreflex
P.O. BOX 4646, PHILADELPHIA, PA 19127
FIBREFLEX
OFFICE and PLANT
5101 Umbria Street
THIO-FLEX
PMILA., PA. 19128
TELEPHONES
· FIBRE-KORK@
Fibre-CorkComposition
@
(215) 482-1604
(215) 482-1490-91
Fax: (215) 487-1220
Telex: 255429 FIBFXUR
GENERAL SPECIFICATIONS
FIBREFLEX "DETROITER"
A. SCOPE:FIBREFLEX "DETROITER" is an excellentgrade of vegetable fibre sheet packing, efficientlysaturated with
a glue-glycerine impregnant rendered insoluble by means of a tanning agent (formaldehyde) to give a strong, flexible,
all-proof packing with properties retained during proper storage and in use.
B. CERTIFICATION: FIBREFLEX "DETROITER" is certified to meet the below listed specifications.
HH-P-96G, Type I only (Federal Specification)
MIL-G-12803A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ident. No. P3313B
MIL-G-12803B & MIL-G-12803C
. . . . . . . . . . . . . . . . . . .Ident. No. F326128M6
ASTM 0 1170and SAE J90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ident. No. P3313B
ASTM F 104and SAE J90
Ident. No. F326128-E21-M6
Underwriters' Laboratory Listing
No. MH 4649 (763N)
C. PHYSICAL CHARACTERISTICS:
Fibre
450/0to 55%
Moisture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6% to 10%
Chemical Solids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35% to 45%
D. CONDITIONING: All samples conditioned prior to testing as specified by applicable application
- 70 to
-
usually 50% RH
85°F for a period of 22 or 24 hours.
E. STANDARDS: (Using American Society of Testing Materials Specification ASTM F 104prepared jointly with the Society
of Automotive Engineers and similar in requirements to MIL-G-12803C.
Test Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 p.s.i.
Compressibility.
. . . . . . . . . . . . . . . . . . . . . . . . . . .25% to 40%
Tensile Strength. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000 p.s.i.
ORIGINAL
PHYSICAL
PROPERTIES
PHYSICAL
Fuel B-Thickness increase
.5% maximum-(Not Applicable to MIL-G-12803C)
PROPERTIES #3 Oil - Thickness increase. . . . . . . .5% maximum
AFTER
Fuel B - Weightincrease. . . . . . . . . .15%maximum-(Not Applicableto MIL-G-12803C)
IMPRESSION #3 Oil - Weight increase . . . . . . . . . . 15%maximum
Water - Weightincrease. . . . . . . . . . 100%maximum
F. THICKNESS TOLERANCES:
Thickness
Plus or Minus
.006",.010"and .015". . . . . . . . . . . . . . .
.0035"
.021",.031",.046'~and .062" . . . . . . . . .
.005"
.096" (3/32") . . . . . . . . . . . . . . . . . . . . . .
.008"
.125"(118")and up
.016"
G. FLEXIBILITY: FIBREFLEX "DETROITER" is capable of withstanding bending around a rod with a diameter of
twice the thickness of the material under test, without cracking, breaking or excessive marring of the surfaces.
H. TEMPERATURE LIMIT:
Rev. 11/93
.
FIBREFLEXPACKING 8r MFG. CO.
INCORPORATED
·
P.O. BOX 4646,
PHILADELPHIA, PA 19127
OFFICE and PLANT
5101 Umbria Street
FIBREFLEX
Vegetable
Fibre Sheet
· Thlokol Coated
· FIBRE-KORK@
PHILA.,PA.19128
THIO-FLEX
TELEPHONES
(215) 482-1604
(215) 482-1490-91
Fax: (215) 487-1220
Telex: 255429 FIBFXUR
Fibreflex
Fibre-Cork Composition
GENERAL SPECIFICATIONS
FIBREFLEX@"GRADE A"
A.SCOPE:
FIBREFLEX@ GRADE "A" is a premium grade of vegetable fibre sheet packing, efficiently saturated with
a glue-glycerine impregnant rendered insoluble by means of a tanning agent (formaldehyde) to give a strong, flexible,
all-proof packing with properties retained during proper storage and in use.
B. CERTIFICATION:
FIBREFLEX@ GRADE "A" is certified to meet the below listed specifications.
HH-P-96G, Type I only (Federal Specification)
MIL-G-12803A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ident. No. P3313B
MIL-G-12803B & MIL-G-12803C
Ident. No. F326128M6
ASTM D 1\70 and SAE J90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ident. No. P3313B
ASTM F 104 and SAE J90
Ident. No. F326128-E21-M6
Underwriters' Laboratory Listing
No. MH 4649 (763N)
C. PHYSICAL
CHARACTERISTICS:
Fibre
45% to 55%
Moisture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6°/., to 10%
Chemical Solids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35% to 45%
D. CONDITIONING: AII samples conditioned prior to testing as specified by applicable application
- 70 to
-
usualIy 50%RH
85°F for a period of 22 or 24 hours.
E. STANDARDS:(Using American Societyof TestingMaterials SpecificationASTM F 104prepared jointly with the Society
of Automotive Engineers and similar in requirements to MIL-G-12803C.
ORIGINAL
Test Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 p.s.i.
PHYSICAL
Compressibility. . . . . . . . . . . . . . . . . . . . . . . . . . . .25% to 40%
PROPERTIES Tensile Strength. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2000 p.s.i.
PHYSICAL
Fuel B - Thickness increase. . . . . . . .5'Yomaximum-(Not
PROPERTIES
#3 Oil - Thickness increase. . . . . . . . 5% maximum
Fuel B- Weight increase
.15% maximum-(Not
#3 Oil - Weight increase . . . . . . . . . . 15%maximum
Water - Weight increase . . . . . . . . . . 100%maximum
AFTER
IMPRESSION
Applicable to MIL-G-12803C)
Applicable to MIL-G-12803C)
F. THICKNESS TOLERANCES:
Thickness
Plus or Minus
.006",.010"and .015". . . . . . . . . . . . . . .
.0035"
.021",.031",.046",and .062" . . . . . . . . .
.005"
.096" (3/32") . . . . . . . . . . . . . . . . . . . . . .
.008"
.125"(lI8") and up
.016"
G. FLEXIBILITY:
FIBREFLEX@ GRADE "A" is capable of withstanding bending around a rod with a diameter of twice
the thickness of the material under test, without cracking, breaking or excessive marring of the surfaces.
H. TEMPERATURE LIMIT:
Rev. 12/94
.
FIBREFLEXPACKING Ie MFG. CO.
INCORPORATED
P.O. BOX 4646, PHILADELPHIA, PA 19127
·
·
·
OFFICE and PLANT
5101 Umbria Street
PHILA.,PA.19128
FIBREFLEX
Vegetable Fibre Sheet
THIO.FLEX
Thlokol Coated Flbreflex
FIBRE.KORK@
Fibre-Cork Composition
TELEPHONES
(215) 482-1604
(215) 482-1490-91
Fax: (215) 487-1220
Telex: 255429 FIBFXUR
GENERAL SPECIFICATIONS
FIBREFLEX "FIBRE-KORK"@
A.SCOPE: FIBRE-KORK is a composition cork and fibre glue-glycerineimpregnant gasket material manufactured and
tested to the below-listed specifications. FIBRE-KORK consists of a special base fibre containing 40%granulated cork
particles by volume. FIBRE-KORK is saturated with a glue-glycerine-formaldehydeimpregnant which makes the sheet
impervious to oil, water and gasoline. The incorporation of the cork with the fibre makes FIBRE-KORK a soft compressible material adaptable for gasket application with low internal pressures.
B. CERTIFICATION: FIBRE-KORK is certified to meet the following specifications.
MIL-G-12803A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ident. No. P3415A
MIL-G-12803B & MIL-G-12803C
Ident. No. F328148M4
ASTM 0 1170and SAE J90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ident. No. P3415A
ASTM F 104 and SAE J90
Ident. No. F328148-E41-M4
C. PHYSICAL CHARACTERISTICS:
Fibre (60% by volume) and Cork (40% by volume)
.45% to 55%
Moisture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6% to 100/.,
Chemical Solids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35% to 45%
D. CONDITIONING: All samples conditioned prior to testing as specified by applicable specifications - usually 50%
RH 70 to 85°F for a period of 22 or 24 hours.
-
E. STANDARDS:(Using American Societyof TestingMaterials SpecificationASTM F 104prepared jointly with the Society
of Automotive Engineers and similar in requirements to MIL-G-12803C.
ORIGINAL
Test Load
1000 p.s.i. min.
PHYSICAL
Compressibility. . . . . . . . . . . . . . . . . . . . . . . . . . . .40% to 55%
PROPERTIES Tensile Strength . . . . . . . . . . . . . . . . . . . . . . . . . 1000p.s.i. min.
PHYSICAL
PROPERTIES
AFTER
IMPRESSION
Fuel B#3 Oil Fuel B#3 Oil Water -
Thickness increase. . . . . . . .5% maximum-{Not Applicable to MIL-G-12803C)
Thickness increase. . . . . . . .5% maximum
Weight increase. . . . . . . . . .30% maximum-{Not Applicable to MIL-G-12803C)
Weight increase . . . . . . . . . .30% maximum
Weight increase ... . . . . . . . 100%maximum
F. THICKNESS TOLERANCES:
Thickness
Plus or Minus
.006",.010"and .015". . . . . . . . . . . . . . .
.0035"
.021",.031",.046",and .062" . . . . . . . . .
.005"
.096" (3/32") . . . .. . . .. . . . .. . . . .. . . .
.008"
.125"(1/8")and up
.016"
G. FLEXIBILITY: FIBREFLEX "FIBRE-KORK" is capable of withstanding bending around a rod with a diameter of
twice the thickness of the material under test, without cracking, breaking or excessive marring of the surfaces.
H. TEMPERATURE LIMIT:
.
Rev. 11193
---