Ch6_PL111 SM - Michael Jay Lissner

Transcription

Service Manual
ViewSonic PJ402D
Model No. VS10400
Portable DLP Projector
(PJ402D_SM Rev. 1a June 2005)
ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright ¤ 2005 by ViewSonic Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of ViewSonic Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular
purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time
to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or
changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision
SM Editing Date
1a
06/14/05
Description of Changes
ECR Number
Editor
N. Huang
Initial Release
Confidential - Do Not Copy
ViewSonic Corporation
i
PJ402D
TABLE OF CONTENTS
1.
Precautions and Safety Notices
1
2.
System Introduction
2
3.
Firmware Update
10
4.
Machine Disassembly and Replacement
12
5.
Troubleshooting
25
6.
Connector Information
35
7.
FRU (Field Replaceable Unit) List
45
8.
Recommended Spare Parts List
49
ii
PJ402D
1. Precautions and Safety Notices
1. When replacing the lamp, use care to avoid burns to your fingers. The lamp becomes very hot
during operation.
2. Never touch the lamp with your fingers as body oil transferred to the lamp can damage the
lamp’s useful life.
3. Never drop the lamp or jar it in any manner. This may cause the lamp to burst.
4. This projector is provided with a high voltage circuit for the lamp. Do not touch any electric
part or component after the projector has been turned on and is operating. Doing so could
induce a severe shock causing injury or death.
5. Do not touch the exhaust fan, nor block its air flow, during operation, as the fan is hot.
6. The LCD module assembly can be easily damaged during service. If replacing the LCD
Lens/Prism assembly, do not hold the FPC of the LCD module assembly.
7. Use only the cables which are included with the projector, or are specified in this manual.
1
PJ402D
2. System Introduction
Technical Specification
Item
Description
Display Type
Single Panel 0.55" DLP Projector
Lamp Type
NUP 200W
Brightness
1500 Lumen (typical)
Contrast Ratio
1500 : 1(Full on/off)
Resolution(Pixels)
800 x 600( 480,000 dot x 1)
Uniformity
80 % (typical)
Optical Compensation
Light Tunnel
Focal Length
20.2 ~ 24.2 mm
Screen Size
30~200 inches
Throw Distance
1.2 ~ 10 Meter
Projection Type
Front, Rear, Ceiling
"Horizontal frequency (31~79KHz" )
Compatibility
"Vertical frequency ( 50~85Hz" )
Pixel Rate 108 MHz
Keystone Correction
Vertical: +/-15
Audio System
2W x 1
Aspect Ratio
1:1 , 16:9 , 4:3
Video Input
PAL , NTSC , SECAM
Input Source
Computer , HDTV , S-Video , Video
Analog RGB (Input Signal)
D-Sub Connector
2
PJ402D
Item
Operati on Humi di ty
D escription
35~85%
3:2 Pull D own
Progressi ve Scan
Blank
Other Key Feature
Auto Source D etecti on
Freeze
Auto Tracki ng/Sync.
Plasti c Body
Sound Noi se
34dB A
Power Requi rement
100~240v, 50~60Hz
D i mensi on(W x D x H)
254 x 202 x 98 mm
Wei ght
2.0 KG (<4.5 lb)
Remote Mouse
Multi functi onal
OSD Language
C hi nesec, C hi nese, Engli sh, French, German,Spani sh,
Itali an, Portuguese, Russi an, Japanese
Power C onsumpti on
250 W
Operati on Temperature
+5 ~ +35C
C erti fi cati on
UL , C E , FC C C lass B , VC C I , C -Ti ck , C C C
Power Supply
AC 100 - 240 V , 50 - 60 Hz
3
PJ402D
Lamp Specification
1.Product Scope
The product is a lamp system consisting of a short arc burner within a reflector, and an
electric lamp driver.
Lamp type
P-VIP 200/1.0 E 17.5
identcode
A390 425 0004
Driver type
PT VIP 3AC/380 O3
identcode
A392 891 0027
2. Product Specifications : P-VIP 200/1.0 E 17.5 lamp
2.1 Dimensions and weight
Lamp
see lamp drawing
Reflector type
elliptical
Cable and connector on request
Lamp weight
< 70g
2.2 Marking on the lamp
Position of marking
On ceramic cap on the backside of reflector
Manufacturer
OSRAM
Type no.
P-VIP 200/1.0 E 17.5
Country of origin
Germany
2.3 Operating and measurement conditions
Ballast type
Test conditions stable at 200W with
OSRAM PT VIP 3 AC/380 O3 ballast
Rated lamp wattage 200W
Burner position
0 degree to +20 degree ( 0 degree optical axis horizontal)
Burning position
horizontal
4
PJ402D
2.4 Temperature
Lamp burner Mo foil , back
Lamp burner Mo wire
Lamp burner Mo foil, front
Burner bulb (top) temperature
< 350 degree C
< 350 degree C
< 350 degree C
860 degree C - 960 degree C (measured with
pyrometer)
Validation of max. permissible temperatures by reference thermocouple measurement
based on a referece lamp housing .
2.5 Rise time
Rise time to 80% of the stabilized luminous output is < 90% sec .
Extensive cooling of the bulb during lamp run-up phase has to be avoided .
2.6 Hot restrike
If the unit has been off for more than 60 sec. the lamp must restrike .
( Ignition voltage 5kV +/- 3kV)
2.7 Light output
Ballast type
Stabilization time
Luminous flux (initial values)
Color coordinates
Test conditions on electronic power supply
OSRAM PT VIP 3 AC/380 o3 stable at 200W
5 min.
typ. : 6300 lm @ 5.0 x 3.8 mm rect. aperture
min. : 5800 lm @ 5.0 x 3.8 mm rect. aperture
typ. x : 0.290 +/- 0.020
typ. y : 0.290 +/- 0.020
5
PJ402D
2.8 Lamp drawing
2.9 Instructions for use
1. The lamp becomes high temperature after turning off the projector with the power
button. If you touch the lamp, you may scald your finger. When you replace the lamp,
wait for at least 45 minutes for the lamp to cool down.
2. Do not touch the lamp glass at any time. The lamp may explode due to improper
handling, including the touching of the lamp glass.
3. Lamp lifetime may differ from lamp to lamp and according to the environment of use.
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or
terminate their lifetime in a shorter period of time than other similar lamps.
4. A lamp may explode as a result of vibration, shock or degradation as a result of hours
of use as its lifetime draws to an end. Risk of explosion may differ according to the
environment or conditions in which the projector and lamp are being used.
5. Wear protective gloves and eyeglasses when fixing or detaching the lamp.
6. Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5
minutes to turn off the projector after powering on.
7. Do not operate the lamp in proximity to paper, cloth, or other combustible material nor
cover it with such materials. Otherwise it could cause a fire.
6
PJ402D
8. Do not operate the lamp in an atmosphere containing an inflammable substance, such
as thinner. Otherwise it could cause a fire or explosion.
9. Thoroughly ventilate the area or the room when operating the lamp in an oxygen
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea,
dizziness, etc.
10. The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the
lamp will go out of the projector. Leave the area immediately if the lamp shatters while
being operated and ventilate the area for at least 30 minutes in order to avoid the
inhalation of mercury fumes. Otherwise it could be harmful to user’s health.
11. Dispose of the used lamp according to local regulations.
12. Ensure that screws are tightened properly. Screws not tightened fully may result in
injury or accidents.
13. Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
14. Do not reuse the old lamp. This could cause the lamp to explode.
15. Be sure to turn off the projector and unplug the AC power cord before replacing the
lamp.
16. Do not use the projector with the lamp cover removed.
Disposal :
For disposal of spent lamps, always consult federal, state, local and
provincial hazardous waste disposal rules and regulations to ensure
proper disposal.
Caution :
This lamp emits ultra violet (UV) radiation and operates at high
pressure.
This lamp may only be used in enclosed fixtures that comply with
UL1572.
Due to the high luminous efficacy, the UV radiation which the lamp
emits and the high pressure within the lamp, P-VIPâ lamps may only be
operated within enclosed, purpose-built housings.
7
PJ402D
System Block Diagram
8
PJ402D
Optics-Conceptual Drawing
9
PJ402D
3. Firmware Upgrade
This chapter provides the equipment needed, setup and upgrading procedure for
Firmware upgrade.
Setup Tool / Equipment
1. Computer
2. USB Cable (see right picture)
3. Power Coard
Upgrading Procedure
1. Connect Download Cable to projector
2.
Open burning programma (DLP Composer Lite)
10
PJ402D
3. Press Power and Menu button together and connect the power cord into the
projector . Than release these 2 bottoms .
4. Click the Start Download button and then start to burning of program .
5. Completion of Burning than remove Power Cord and Burning Cord .
11
PJ402D
4. Machine Disassembly and Replacement
This section provides disassembly procedures for PD-S600 DLP Projector. Before you begin
any of these procedures, be sure to turn off the power, computer system, and other attached
devices; then disconnect the power cable from the electronically outlet. Moreover, when you
disassemble the projector, be sure to put the screws in a safe place and separate them according to grouping.
Tool Needed
Item
PHOTO
Long Nose Nipper
Hex Sleeves 5mm
Screw Bit (+) : 107
Screw Bit (+) : 101
Screw Bit (+) : 102
12
PJ402D
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
3. Wear Anti-static wrist strap.
13
PJ402D
Disassemble Lamp Module
Note:Unplug all the cord before disaddembling the Projector.
1.
2.
3.
4.
Loosen two screws of Lamp Cover
Remove Lamp Cover
Loosen two screws of Lamp Module .
Grasp the lamp handle and pull out Lamp Module
p.s Related notice of replace lamp pls refer to the Lamp Specification section .
14
PJ402D
Disassemble FroŠ
Top Cover
1.
2.
3.
Turn over the Projector.
Remove four 4 screws of bottom cover.
Remove the front cover set.
1.
2.
Remove the 4 screws of back cover.
Life up top cover directly (Be careful there is a internal wire connect with the main board)
15
PJ402D
Disassemble Key Pad , Speaker & Front IR Board
1.
2.
Remove the all screws of top cover.
Life up all components include key pad , speaker , front IR board .
02595-0014-00
01635-361 *7
Disassemble Front Fan
1.
Then life up the fan set directly .
P1643-0021
16
PJ402D
Disassemble Main Board
1.
2.
3.
Remove the five screws of main board .
Unplug all wires on the board (Main Board PIN location of connectors pls refer to
Chapter 5 )
Remove the Main Board.
17
PJ402D
Disassemble IO Cover and Video Baord
1.
2.
Unscrew two screws of the IO cover.
Separate all parts individually .
18
PJ402D
Disassemble Ballast Module
1.
2.
3.
Unplug all wires on Ballast Module (Ballast Board PIN location of connectors pls refer
to Chapter 5 )
Unscrew four screws on Ballast Module.
Remove the Ballast Module.
01635-361 *2
01635-366 *2
P1643-0016
Unscrew than life up the IR board
01635-A44-N *4
P1647-9000
P1638-152
P1635-055
19
PJ402D
Disassemble Optical Engine
1.
2..
3.
4.
Unplug the wire inside.
Unscrew four screws on Optical Engine.
Then remove the Engine Module.
Be careful don’t let the Engine go down due to the heavy machine.
P1635-600
P1638-102
Unscrew three screws than remove the fan .
P1643-0020
P0335-101 *3
20
PJ402D
Disassemble Power Outlet Set
1.
2.
Remove the screw from the bottom of power wires and unplug the connector.
Then lift up the power outlet set.
21
PJ402D
Disassemble Power Board
1.
2.
3.
Unplug all the wires on the board (Power Board PIN location of connectors pls refer to
Chapter 5 )
Unscrew five screws on Power Board.
Then remove Power Board.
22
PJ402D
Disassemble Foot Screw Assembly
1.
2.
3.
Push buttom let foot screw assembly fall off.
Use nipper or tweezers carfully to press the head of foot screw .
Then foot screw assembly drop out by itself .
82134-465
82135-351
82134-464-99
P1634-466
23
PJ402D
Exploded overview
Ballast exploded overview
24
PJ402D
5. Troubleshooting
This chapter provides technicians and people who have an electronic background a primary
description about maintaining the product. Moreover, you can get the appropriate operation
to solve some complicated problems of component repairing and professional problems.
The Troubleshooing section focus on below items:
1.
Video Signal Troubleshooting
2. Operation Function Troubleshooing
3.
Power Source Troubleshooting
25
PJ402D
Video Signal
Video
No Signal
Computer
No Signal
Check
Source
NG
NG
Replace
Cable
Check
Cable
NG
Video
Mode
Input
NG Change to
Replace
Cable
OK
OK
Computer
Mode
Input
Turn on
Source
OK
OK
Check
Cable
NG
Check
Source
Turn on
Source
NG
Change to
Computer
Mode
Video Mode
OK
OK
Change Main
Board
Change Main
Board
26
PJ402D
Fail to light up
OK
Check
LED indication
NG
Look up user
manual ,and
follow indicative action
Check
Optical Engine
NG
Replace Optical
Engine
OK
Check
Lamp
NG
Replace Lamp
OK
Check
Fan
NG
Replace Fan
OK
Check
C/W wire loose or
not
NG Connect C/W
cable completely
OK
Check
Ballast
NG
Replace
Ballast
NG
Replace Main
Board
OK
Check
Main Board
27
PJ402D
Color Missing
On Screen
No Volume
Check
source and mute
function
NG Input the correct
Check
Cable
source to Projector
OK
Check
Top cover’s cable
NG Replace cable
C/W Sensor
Cable
Connector
or connect the
cable back
Cable
NG
Check C/W Sensor
Cable Connector
become loose or
not
OK
NG
Speaker
Connector
Become loose
Check Main
Board
NG Change Main
Board
OK
OK
Check
Speaker
Replace
OK
OK
Check
Speaker
Connector
NG
NG
Change Optical
Engine
Replace
Speaker
OK
Check
keypad
NG
Replace keypad
OK
Check
Main
Board
NG
Replace Main
28
PJ402D
Operation Function:
Remote Control
Failure
Check
Battery
Level
Button Failure
NG
Replace Battery
NG Replace Remote
Control
or connect the
cable back
Check
Button
NG
Replace Button
OK
OK
Check
IR Board or IR cable
NG Replace cable
OK
OK
Check
Remote
Control
Check
Top cover’s cable
NG Replace IR
Check
Keypad
Board or IR
cable
OK
NG
Replace Keypad
OK
Replace
Main Board
Main
Board Fail
29
PJ402D
Power Source:
No Power Source
After Turning On
Check
Power Cord
Fan failure After
Turning On
NG
Check
Fan
Connector
Replace
Power Cord
OK
Check
Lamp Cover
Switch
NG Replace Lamp
Cover or
Reassembly
NG Replace
Check
Fan
keypad
cable...
NG
Replace Inner
Wires
NG
R e p l ac e
Fan
OK
NG Replace
Power Board
wire
Check
Main
Board
NG
Replace
Main Board
OK
OK
Check
Main
Board
Check
Inner
Wires
OK
OK
Check
Power
Board wire
Fan Connector
Become loose
OK
OK
Check
Top Cover (keypad
cable...)
NG
NG Replace Main
Board
Replace Power
Baord
OK
Check
Power
Board
NG Replace
Power Board
30
PJ402D
Function Test and Alignment
Equipment Needed
Item
Description
1
PC with SVGA resolution (Color Video Signal & Pattern Generator)
2
Remote Controller
3
Test Cable
4
Power Cord
5
DVD Player
Test Condition
Item
Description
1
Circumstance Brightness : Dark room less than 60 lux
2
Inspection Distance : 1.8m
3
Screen Size : 60 inches diagonal (wide)
4
Before function test and alignment, each PD-S600 should be run-in and
warmed-up for at least 5 minutes with following conditions.
1.) In room temperature
2.) With cycled display colors (R,G,B,White)
3.) With cycled display modes
640 x 350 (H=31.5 KHz, V=70 Hz)
640 x 400 (H=31.5 KHz, V=70 Hz)
640 x 480 (H=37.5 KHz, V=75 Hz)
720 x 400 (H=31.5 KHz, V=70 Hz)
800 x 600 (H=53.7 KHz, V=85 Hz)
800 x 600 (H=37.9 KHz, V=60 Hz)
1024 x 768 (H=48.4 KHz, V=60 Hz)
1024 x 768 (H=68.7 KHz, V=85 Hz)
5
Test Display Mode and Pattern
31
PJ402D
Test Display Modes and Patterns
Compatible Modes
Preset Signal
VGA
SVGA
XGA
S yn c
H(+), V(-)
H(-), V(+)
H(-), V(-)
Resolution
H(-), V(-)
fH(Hz )
Siz e
59.94
31.469
800
72.809
37.861
832
75
37.5
840
85.008
43.269
832
56.25
35.156
1024
60.317
37.879
1056
72.188
48.077
1040
75
46.875
1056
85.061
53.674
1048
60.004
48.363
1344
70.069
56.476
1328
75.029
60.023
1312
84.997
68.677
1376
70.016
63.995
1472
75
67.5
1600
85.057
77.487
1568
60
60
1800
75
75
1680
60.02
63.981
1688
640 x 800
800 x 600
1024 x 768
H(+), V(+)
SXGA
fV(Hz )
1152 x 864
H(-), V(-)
H(+), V(+)
SXGA
1280 x 960
H(+), V(+)
SXGA
H(+), V(+)
1280 x 1024
32
PJ402D
Function Test Display Pattern
Item
1
Test C ontent
Noi se check up
Pattern
Specification
R emark
12 squares
(1).Select the "12 squares" BMP
fi le to check i f there i s any
noi ses duri ng the stage of
turni ng on, and warmi ng up the
projector.
Fi gure 1
12 squares
(2). The noi ses appear on the
square should be less than
three squares.
Fi gure 1
800 fli cker
(3).Select the " 800 fli cker" BMP
fi le. Make sure teach word on
the projected i mage doesn not
fli cker.
Fi gure 2
2
D ust check up
Full Black
(1) Select the " Full Black" BMP fi le
to project the i mage on the
Fi gure 3
screen .Stand 1.8 meters from i t
and ensure there are no stai ns .
3
D ust check up
Full Whi te
(1) Select the " Full Whi te" BMP fi le
Fi gure 4
4
5
6
7
Resoluti on check up
RGB color check up
D ust check up
Li ght leakage check
up
(1) Select the " black and whi te
word" BMP fi le. Use the
projector to adjust the projected
i mage to the maxi mum si ze
and mi ni mum si ze and make
sure each word i s
di sti ngui shable under both
condi ti ons.
Fi gure 5
256RGB
(1) Select the "256RGB" BMP fi le
to check i f the color ladder of
the i mage matches the color
ladder of the fi le.
Fi gure 6
Full Gray
(1) Select the " Full Gray " BMP fi le
Fi gure 7
Boundary
Frame
(1) C li ck on the folder, select the "
Boundary Frame " BMP fi le,
press the AUTO button on the
projector, check i f the li nes and
colors of the projected i mage
are clear as presented on the
BMP fi le .
Black and
Whi te Word
Fi gure 8
33
PJ402D
Full Black Pattern (Figure 3)
Full White Pattern (Figure 4)
Black and White Word Pattern (Figure 5)
256RGB Pattern (Figure 6)
Gray Pattern (Figure 7)
Boundary Frame (Figure 8)
34
PJ402D
6. Connector Information
Introduction
This section provides each connector location on boards, signal and function of each
board. They will be useful for your detecting the defective boards.
Main Board
Summarize
C onnector
D escription
C N1
IR
C N2
Keypad control
C N3
F an
C N4
F an
C N5
F an
C N6
F an
C N7
IR
J1
Ballast control
J2
Thermal
J3
Vi di o & S-Vi deo i n
J5
D MD connector
J7
Phone jack stereo-R
J8
C olor wheel
J9
Power i n
J1 5
Vi di o & S-Vi deo i n
JP 1
USB
JP 3
C W i ndex
JP 4
Fi rmware debug
JP 5
Standby run
C ON1
D -SUB
C ON2
V i deo
C ON3
S-vi deo
35
PJ402D
The Locations of Connectors
CN1 , CN7 : IR
CN3 , CN4 , Cn5 : FAN
J1 :Ballast Control
36
PJ402D
CN2 : Keypad Control
37
PJ402D
J2 :Thermal
J3 , J15 : Video & S-Videop IN
CON2 : Video
CON3 : S-Video
38
PJ402D
CON1 : D_SUB
J7 : Phone jack Stereo-R
J8 : Color Wheel
39
PJ402D
J9 : Power Supply
JP1 : USB
JP3 : CW Index
JP3 : CW Index
40
PJ402D
JP4 : FirmWare Debug
41
PJ402D
Power Board
Summarize
CN101 : AC Inout
42
PJ402D
CN201 : +380V Output
CN301 :DC Output
43
PJ402D
Ballast Board
Summarize
CN1 : Lamp Signal
CN2 : 380V
CN3 : 380V
44
PJ402D
7. FRU (Field Replaceable Unit) List
This chapter gives you FRU ( Field Replaceable Unit ) listing in global configuration of S600.
Refer to this chapter whenever ordering for parts to repair or for RMA ( Return Merchandise
Authorization ). Please note that WHEN ORDERING FRU PARTS, you should check the most
up-to-date information available on your regional web or channel. For whatever reasons a part
number change is made, it will not be noted on the printed Service Guide. For Premier AUTHORIZED SERVICE PROVIDERS, Premier office may have a DIFFERENT part number code
from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list
provided by your regional Premier office to order FRU parts for repair and service of customer
machines.
NOTE : To scrap or to return the defective parts, you should follow the local government
ordinance or regulations on how to dispose it properly, or follow the rules set by your
regional Premier office on how to return it.
45
PJ402D
FRU List
No.
Photo
Part Name
P/N
1
Mai n Board
P1647-0001
2
Ballast Board
P1647-9000
3
Power Board
P1647-8001
4
K ey pad
P1684-0006
5
Front IR Board
P1647-6001
6
Back IR Board
P1647-5001
7
Thermal Board
P1647-3000
8
op cover
9
Bottom cover
P1634-451-99
10
Front cover
P1634-452-99
P1684-000
46
PJ402D
No.
Photo
Part Name
P/N
11
Front IR cover
P1634-461-99
12
IO cover
P1634-465-99
13
Foot screw assembly
P1643-0012
14
Opti cal Engi ne
P1643-0002
15
Lamp Module
P1643-0014
16
FAN x 1
P1643-0020
17
FAN X2
P1643-0021
18
S p e a ke r
02413-0016-00
19
FFC cable
02595-0014-00
20
Wi re 4P C /W
02595-0017-00
47
PJ402D
No.
Photo
Part Name
P/N
21
Wi re 3P IR/F
02595-0016-00
22
Wi re 3P IR/B
02595-0027-00
23
Wi re 5P BST
02595-0015-00
24
Wi re 2P-4P Lamp
02595-0025-00
25
Wi re 2P 380V
02595-0019-00
26
Wi re 12P-10+2P
PWR BD
02595-0014-00
27
Wi re 2P AC Socket
02595-0028-00
48
PJ402D
8. Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST (PJ402D-1)
ViewSonic Model Number: VS10400-1W
Rev: 1a
Serial No. Prefix: PD4
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Description
AC POWER CORD
LAMP MODULE
REMOTE CONTROLLER
PC Board Assembly: MAIN BOARD
OSRAM BALLAST
PD-S600 IR PCB/F
PD-S600 IR PCB/R
PD-S600 KEYPAD+METAL DOME
PD-S600 PFC, POWER
PD-S600 THERMAL PCB
BACK IR COVER
Cabinets:
BOTTOM COVER
FRONT COVER
FRONT IR COVER
IO COVER
LAMP COVER + ISOLATOR
LENS COVER
TOP COVER (include keystroke , back
IR cover ,side cover)
AUDIO CABLE
Cables:
FFC CABLE 0.5P 28P
S-VIDEO CABLE
VGA (D-SUB) to HDTV(RCA) CABLE
VGA CABLE
WIRE CON-CON 12P-10+2P PWR BD
WIRE CON-CON 2P 380V
WIRE CON-CON 2P AC SOCKET
WIRE CON-CON 2P-4P LAMP
WIRE CON-CON 3P IR/F
WIRE CON-CON 3P IR/R
WIRE CON-CON 4P C/W
WIRE CON-CON 5P BST
CD ROM
Documentation:
Instruction manual
OPTICAL ENGINE (include Fan)
Electronics:
SPEAKER
CU FOOT SCREW
Hardware:
S: M1.7*2 BL
S: M3*10*A2 BL
S: M3*18*A2 NI
S: M3*28.5*E1.2 BL
S: M3*6*A2 BL
S: M3*6*D2 BL
S: M4*6*A3 NI
S: T3*5*A3 BL
S: T3*8*A2 NI
S: T4*10*A2.5 NI
SHD-PWR-BD-PD-S600
WSC:8*4.3*1FE/NI S-GTY
FAN (OE) FAL3F12LLSC Assy
Miscellaneous:
FAN MODULE_PD-S600
MESH
MYLAR-POWER-BD-PD-S600
UV/IR FILTER
Accessories:
ViewSonic P/N
A-00003061
RLC-001
A-00003062
B-00003063
B-00003064
B-00003065
B-00003066
B-00003067
B-00003068
B-00003069
C-00003070
C-00003071
C-00003072
C-00003073
C-00003074
C-00003075
C-00003076
Ref. P/N
According to POI
P1684-0001
82143-4000
P1684-0000
P1684-0005
P1647-6001
P1647-5001
P1684-0006
P1684-0007
P1647-3000
P1634-462
P1684-0004
P1684-0002
P1634-461
P1634-465
P1643-0013
P1634-458
Q'ty
MOQ
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C-00003077
CB-00003078
CB-00003079
CB-00003080
CB-00003081
CB-00003082
CB-00003083
CB-00003084
CB-00003085
CB-00003086
CB-00003087
CB-00003088
CB-00003089
CB-00003090
DC-00003091
DC-00003092
E-00003093
E-00003094
M-SCW-0824-6923
M-SCW-0824-6913
HW-00003095
HW-00003096
HW-00003097
HW-00003098
HW-00003099
M-SCW-0824-6918
HW-00003100
M-SCW-0824-6917
M-SCW-0824-6910
HW-00003105
M-SCW-0824-6916
M-00003101
M-00003102
M-00003103
M-00003104
M-00003106
P1684-0003
According to POI
02595-0014-00
02547-1007
According to POI
According to POI
02595-0014-00
02595-0019-00
02595-0028-00
02595-0025-00
02595-0016-00
02595-0027-00
02595-0017-00
02595-0015-00
P1639-A001-00
P1639-406-VIE
P1684-0008
02413-0016-00
01635-B77
01635-366
P0335-101
01635-A44-N
01635-C98-N
01635-C01
82035-251
01635-A08
01635-353
01635-A01
01635-361
P1635-052
01635-705
P1643-0020
P1643-0021
P1638-156
P1638-150
P1636-764
1
1
1
1
1
49
1
1
1
1
1
1
1
1
1
1
1
1
1
17
56
25
15
16
12
8
3
18
3
48
1
3
1
1
1
1
1
1
1
1
100
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
PJ402D
Item
54
55
56
57
58
59
60
61
62
Packing Material:
Plastics:
Description
CABLE BAG
EPE
OUTER CARTON
PAD
PE BAG
POUCH
FOOT ASSEMBLY
FUNCTION KEYSTROKE
KEYSTROKE
ViewSonic P/N
P-00003107
P-00003108
P-00003109
P-00003110
P-00003111
P-00003112
PL-00003113
PL-00003114
PL-00003115
Ref. P/N
04039-184
04039-544
P1639-6003-00
P1639-690
04039-145
P1639-306-VIE
P1643-0012
P1634-460
P1634-459
50
Q'ty
1
2
1
1
1
1
1
1
1
MOQ
1
1
1
1
1
1
1
1
1
PJ402D
*Readers Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
U nit
Ex cellent
Fair
G ood
Bad
1. Precautions and Safety Notices
2. System Introduction
3. Firmware Update
4. Machine Disassembly and Replacement
5. Troubleshooting
6. Connector Information
7. FRU (Field Replaceable Unit) List
8. Recommended Spare Parts List
B. Are you satisfied with this Service Manual?
It em
Ex cellent
G ood
Fair
Bad
1. Service Manual Content
2. Service Manual Layout
3. The form and listing
C. Do you have any other opinions or suggestions regarding this service manual?
Readers basic data:
Name:
Title:
Company:
Add.:
Fax:
Tel:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes
([email protected])
51
PJ402D

Ch6_PL111 SM - Michael Jay Lissner

Transcription

Similar documents

pJD5123

networkable high brightness projector

GERTIFICATE M

E2 ® S eries

Toio lamp negative commentary

Overhead Projector - Conference Room AV

VX1935wm - ViewSonic

VX2235wm - ViewSonic