GreenSeeker RT200 System Installation and Operation Guide

Transcription

INSTALLATION AND OPERATION GUIDE
GreenSeeker® RT200 System
Version 1.00
Revision M
April 2010
Part Number 500-1-032
*500-1-032*
F
Trimble Navigation Limited
Trimble Agriculture
10355 Westmoor Drive
Suite #100
Westminster, CO 80021
USA
[email protected]
www.trimble.com
Legal Notices
Copyright and Trademarks
© 2010, Trimble Navigation Limited. All rights reserved.
Trimble, the Globe & Triangle logo, AgGPS, FmX, GreenSeeker, Nomad,
and Recon are trademarks of Trimble Navigation Limited, registered in
the United States and in other countries.
Microsoft, ActiveSync, Windows, Windows Mobile, and Windows Vista
are either registered trademarks or trademarks of Microsoft Corporation
in the United States and/or other countries.
All other trademarks are the property of their respective owners.
This product is covered by the following patents: 5,585,626, 5,296,702,
and 5,389,781.
Release Notice
This is the April 2010 release (Revision M) of the GreenSeeker RT200
System Installation and Operation Guide, part number 500-1-032. It
applies to version 1.00 of the GreenSeeker RT200 system.
LIMITED WARRANTY TERMS AND CONDITIONS
Product Limited Warranty
Subject to the following terms and conditions, Trimble Navigation
Limited ("Trimble") warrants that for a period of one (1) year from date
of purchase this Trimble product (the "Product") will substantially
conform to Trimble's publicly available specifications for the Product
and that the hardware and any storage media components of the
Product will be substantially free from defects in materials and
workmanship.
Product Software
Product software, whether built into hardware circuitry as firmware,
provided as a standalone computer software product, embedded in flash
memory, or stored on magnetic or other media, is licensed solely for use
with or as an integral part of the Product and is not sold. If accompanied
by a separate end user license agreement ("EULA"), use of any such
software will be subject to the terms of such end user license agreement
(including any differing limited warranty terms, exclusions, and
limitations), which shall control over the terms and conditions set forth
in this limited warranty.
Software Fixes
During the limited warranty period you will be entitled to receive such
Fixes to the Product software that Trimble releases and makes
commercially available and for which it does not charge separately,
subject to the procedures for delivery to purchasers of Trimble products
generally. If you have purchased the Product from an authorized Trimble
dealer rather than from Trimble directly, Trimble may, at its option,
forward the software Fix to the Trimble dealer for final distribution to
you. Minor Updates, Major Upgrades, new products, or substantially
new software releases, as identified by Trimble, are expressly excluded
from this update process and limited warranty. Receipt of software Fixes
or other enhancements shall not serve to extend the limited warranty
period.
For purposes of this warranty the following definitions shall apply: (1)
"Fix(es)" means an error correction or other update created to fix a
previous software version that does not substantially conform to its
Trimble specifications; (2) "Minor Update" occurs when enhancements
are made to current features in a software program; and (3) "Major
Upgrade" occurs when significant new features are added to software, or
when a new product containing new features replaces the further
development of a current product line. Trimble reserves the right to
determine, in its sole discretion, what constitutes a Fix, Minor Update,
or Major Upgrade.
Warranty Remedies
If the Trimble Product fails during the warranty period for reasons
covered by this limited warranty and you notify Trimble of such failure
during the warranty period, Trimble will repair OR replace the
nonconforming Product with new, equivalent to new, or reconditioned
parts or Product, OR refund the Product purchase price paid by you, at
Trimble's option, upon your return of the Product in accordance with
Trimble's product return procedures then in effect.
2
How to Obtain Warranty Service
To obtain warranty service for the Product, please contact your local
Trimble authorized dealer. Alternatively, you may contact Trimble to
request warranty service at +1-408-481-6940 (24 hours a day) or e-mail
your request to [email protected]. Please be prepared to
provide:
– your name, address, and telephone numbers
– proof of purchase
– a copy of this Trimble warranty
– a description of the nonconforming Product including the model
number
– an explanation of the problem
The customer service representative may need additional information
from you depending on the nature of the problem.
Warranty Exclusions and Disclaimer
This Product limited warranty shall only apply in the event and to the
extent that (a) the Product is properly and correctly installed,
configured, interfaced, maintained, stored, and operated in accordance
with Trimble's applicable operator's manual and specifications, and; (b)
the Product is not modified or misused. This Product limited warranty
shall not apply to, and Trimble shall not be responsible for, defects or
performance problems resulting from (i) the combination or utilization
of the Product with hardware or software products, information, data,
systems, interfaces, or devices not made, supplied, or specified by
Trimble; (ii) the operation of the Product under any specification other
than, or in addition to, Trimble's standard specifications for its products;
(iii) the unauthorized installation, modification, or use of the Product;
(iv) damage caused by: accident, lightning or other electrical discharge,
fresh or salt water immersion or spray (outside of Product
specifications); or exposure to environmental conditions for which the
Product is not intended; (v) normal wear and tear on consumable parts
(e.g., batteries); or (vi) cosmetic damage. Trimble does not warrant or
guarantee the results obtained through the use of the Product, or that
software components will operate error free.
NOTICE REGARDING PRODUCTS EQUIPPED WITH
TECHNOLOGY CAPABLE OF TRACKING SATELLITE SIGNALS
FROM SATELLITE BASED AUGMENTATION SYSTEMS (SBAS)
(WAAS/EGNOS, AND MSAS), OMNISTAR, GPS, MODERNIZED GPS
OR GLONASS SATELLITES, OR FROM IALA BEACON SOURCES:
TRIMBLE IS NOT RESPONSIBLE FOR THE OPERATION OR
FAILURE OF OPERATION OF ANY SATELLITE BASED
POSITIONING SYSTEM OR THE AVAILABILITY OF ANY
SATELLITE BASED POSITIONING SIGNALS.
THE FOREGOING LIMITED WARRANTY TERMS STATE TRIMBLE'S
ENTIRE LIABILITY, AND YOUR EXCLUSIVE REMEDIES, RELATING
TO THE TRIMBLE PRODUCT. EXCEPT AS OTHERWISE EXPRESSLY
PROVIDED HEREIN, THE PRODUCT, AND ACCOMPANYING
DOCUMENTATION AND MATERIALS ARE PROVIDED "AS-IS" AND
WITHOUT EXPRESS OR IMPLIED WARRANTY OF ANY KIND, BY
EITHER TRIMBLE OR ANYONE WHO HAS BEEN INVOLVED IN ITS
CREATION, PRODUCTION, INSTALLATION, OR DISTRIBUTION,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
TITLE, AND NONINFRINGEMENT. THE STATED EXPRESS
WARRANTIES ARE IN LIEU OF ALL OBLIGATIONS OR LIABILITIES
ON THE PART OF TRIMBLE ARISING OUT OF, OR IN CONNECTION
WITH, ANY PRODUCT. BECAUSE SOME STATES AND JURISDICTIONS
DO NOT ALLOW LIMITATIONS ON DURATION OR THE EXCLUSION
OF AN IMPLIED WARRANTY, THE ABOVE LIMITATION MAY NOT
APPLY OR FULLY APPLY TO YOU.
Limitation of Liability
TRIMBLE'S ENTIRE LIABILITY UNDER ANY PROVISION HEREIN
SHALL BE LIMITED TO THE AMOUNT PAID BY YOU FOR THE
PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, IN NO EVENT SHALL TRIMBLE OR ITS SUPPLIERS
BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGE WHATSOEVER UNDER ANY
CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANYWAY TO THE
PRODUCTS, SOFTWARE AND ACCOMPANYING DOCUMENTATION
AND MATERIALS, (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS
OF DATA, OR ANY OTHER PECUNIARY LOSS), REGARDLESS OF
WHETHER TRIMBLE HAS BEEN ADVISED OF THE POSSIBILITY OF
ANY SUCH LOSS AND REGARDLESS OF THE COURSE OF DEALING
WHICH DEVELOPS OR HAS DEVELOPED BETWEEN YOU AND
TRIMBLE. BECAUSE SOME STATES AND JURISDICTIONS DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE
LIMITATION MAY NOT APPLY OR FULLY APPLY TO YOU.
PLEASE NOTE: THE ABOVE TRIMBLE LIMITED WARRANTY
PROVISIONS WILL NOT APPLY TO PRODUCTS PURCHASED IN
THOSE JURISDICTIONS (E.G., MEMBER STATES OF THE
EUROPEAN ECONOMIC AREA) IN WHICH PRODUCT
WARRANTIES ARE THE RESPONSIBILITY OF THE LOCAL
TRIMBLE AUTHORIZED DEALER FROM WHOM THE PRODUCTS
ARE ACQUIRED. IN SUCH A CASE, PLEASE CONTACT YOUR
LOCAL TRIMBLE AUTHORIZED DEALER FOR APPLICABLE
WARRANTY INFORMATION.
Official Language
THE OFFICIAL LANGUAGE OF THESE TERMS AND CONDITIONS IS
ENGLISH. IN THE EVENT OF A CONFLICT BETWEEN ENGLISH AND
OTHER LANGUAGE VERSIONS, THE ENGLISH LANGUAGE SHALL
CONTROL.
Registration
To receive information regarding updates and new products, please
contact your local Trimble authorized dealer or visit the Trimble website
at www.trimble.com/register. Upon registration you may select the
newsletter, upgrade, or new product information you desire.
EXTENDED LIMITED WARRANTY TERMS AND
CONDITIONS
This Trimble Navigation Limited Product comes with Trimble's
Extended Limited Warranty coverage for serialized hardware
components for a period of one (1) year commencing on the first
anniversary of date of purchase; and except as otherwise stated herein is
provided under the same terms and conditions as those of the standard
Trimble Limited Warranty Terms and Conditions1 with which the
Product is sold and distributed.
The Extended Limited Warranty applies to serialized hardware
components (as configured at the time of purchase) of the Product and
includes updates to associated Product firmware2 but does not apply to
consumable parts (such as batteries), application software, or to
detachable components or accessories that are separately warranted
and furnished solely with Trimble's standard one (1) year limited
warranty.
Registration
To receive product upgrades included with this Extended Limited
warranty as well as information regarding updates and new products,
please register by visiting the Trimble website at
www.trimble.com/register. Upon registration you may select the
newsletter, upgrade or new product information you desire.
PLEASE NOTE: THE TRIMBLE NAVIGATION LIMITED EXTENDED
LIMITED WARRANTY WILL NOT APPLY TO PRODUCTS
PURCHASED IN THOSE JURISDICTIONS (E.G., MEMBER STATES
OF THE EUROPEAN ECONOMIC AREA) IN WHICH PRODUCT
WARRANTIES ARE THE RESPONSIBILITY OF THE LOCAL DEALER
FROM WHOM THE PRODUCTS ARE ACQUIRED. IN SUCH A CASE,
PLEASE CONTACT YOUR LOCAL TRIMBLE DEALER FOR
APPLICABLE WARRANTY INFORMATION.
Europe
This product has been tested and found to comply with
the requirements for a Class B device pursuant to
European Council Directive 89/336/EEC on EMC,
thereby satisfying the requirements for CE Marking and
sale within the European Economic Area (EEA).
Contains Infineon radio module ROK 104001. These
requirements are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential or
commercial environment.
Australia and New Zealand
This product conforms with the regulatory requirements of the
Australian Communications Authority (ACA) EMC framework,
thus satisfying the requirements for C-Tick Marking and sale
within Australia and New Zealand.
Korea
이 제품은 한국 방송통신위원회 (KCC) 의
규제요건에 부합하므로 KCC 마크 표시 및
한국내 판매 요건을 충족합니다 .
This product conforms with the regulatory requirements of the Korean
Communications Commission (KCC), thus satisfying the requirements
for KCC Marking and sale within Korea.
Notice to Our European Union Customers
For product recycling instructions and more information, please go to
www.trimble.com/ev.shtml.
Recycling in Europe: To recycle Trimble WEEE (Waste
Electrical and Electronic Equipment, products that run on
electrical power.), Call +31 497 53 24 30, and ask for the "WEEE
Associate". Or, mail a request for recycling instructions to:
Trimble Europe BV
c/o Menlo Worldwide Logistics
Meerheide 45
5521 DZ Eersel, NL.
Notes
1. A copy of the Trimble Navigation Limited Limited Warranty Terms
and Conditions is provided with the distributed Product and is available
from your local Trimble authorized dealer and upon request at
[email protected].
2. "Firmware" means software used in the hardware device to enable the
different hardware systems to communicate and function together.
These functions are essential to the performance of the hardware device.
Notices
For a complete list of notices for the GreenSeeker RT200 system, refer to
the documentation for each component of the system. Notices not
covered in the additional documentation are provided below.
Class B Statement - Notice to Users. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the receiver.
– Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer
or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission rules.
3
4
Safety Information
Before you start the installation, you must read and understand the information
contained in this section.
Always follow the instructions that accompany a Warning or Caution. The information
they provide is intended to minimize the risk of personal injury and/or damage to
property. In particular, observe safety instructions that are presented in the following
format:
C
WARNING – This alert warns of a potential hazard, which, if not avoided, can cause
severe injury.
C
CAUTION – This alert warns of a hazard or unsafe practice which, if not avoided, can
cause injury or damage.
Note – An absence of specific alerts does not mean that there are no safety risks involved.
Warnings
C
WARNING – If someone else attempts to drive the vehicle while you are working on or
under it, you can suffer serious or fatal injuries. To avoid this possibility, install a lockout
box on the battery terminal to prevent the battery from being reconnected, remove the
key from the vehicle's ignition switch, and attach a "Do not operate" tag in the cab.
C
WARNING – Vehicle cabs can be quite high in the air. To avoid potentially serious injury
through falling from this height, always use the steps and handrails, and face the vehicle,
when you enter or exit it.
C
WARNING – Do not remove/cut or bypass the auto adapter end of the power adapter
cable for the PDA. Do not connect directly to 12 V DC as this will cause immediate failure
of the PDA.
C
WARNING – There are no field serviceable components of the electronic system; do not
attempt any field repair of a malfunctioning controller or sensors. If you experience
operating problems, contact your local dealer or representative or GreenSeeker
distributor for assistance.
C
WARNING – The system installation may bring you into contact with chemical substances,
such as oil, which can cause poisoning. Wash your hands thoroughly after you finish
working on the system.
5
Safety Information
6
C
WARNING – Battery posts, terminals, and related accessories contain lead and lead
compounds, which can cause serious illness. To avoid ingesting lead, wash your hands
thoroughly after touching the battery.
C
WARNING – Always wear protective equipment appropriate to the job conditions and
the nature of the vehicle. This includes wearing protective glasses when you use
pressurized air or water, and correct protective welder's clothing when welding. Avoid
wearing loose clothing or jewelry that can catch on machine parts or tools.
C
WARNING – Parts of the vehicle may be under pressure. To avoid injury from pressurized
parts, relieve all pressure in oil, air, and water systems before you disconnect any lines,
fittings, or related items. To avoid being sprayed by pressurized liquids, hold a rag over fill
caps, breathers, or hose connections when you remove them. Do not use your bare hands
to check for hydraulic leaks. Use a board or cardboard instead.
C
WARNING – Always read chemical manufacturer's instructions before handling or
spraying chemicals.
C
WARNING – Always install boom stop before working under or around raised spray
booms.
Safety Information
Cautions
C
CAUTION – The GreenSeeker RT200 system works with GPS receivers and spray
controllers. Be sure to read and understand the other manufacturer's manuals and
equipment before operating the system.
C
CAUTION – GreenSeeker sensors are designed to operate in harsh environments. The
sensor enclosure and connections are environmentally sealed. Although the sensor is
sealed, DO NOT wash the sensor directly with a high pressure washer. To clean the sensors,
use low pressure and gentle washing procedures.
7
Safety Information
8
Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
System overview. . . . . . . . . . . . . . . . .
Definitions of terms . . . . . . . . . . . . . .
Care and maintenance. . . . . . . . . . . . .
Resources . . . . . . . . . . . . . . . . . . . . .
PDA support: Tripod Data Systems
Other resources . . . . . . . . . . . . .
GPS . . . . . . . . . . . . . . . . . . . . . . . . .
Technical assistance . . . . . . . . . . . . . .
Your comments . . . . . . . . . . . . . . . . .
2
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
12
13
13
14
14
15
15
15
15
Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
System layout with the Trimble Recon handheld . . . . .
System layout with Trimble Nomad handheld . . . . . . .
System layout with Trimble AgGPS FmX display . . . . .
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RT200 interface module . . . . . . . . . . . . . . . . . . . . .
User interface . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ruggedized PDA . . . . . . . . . . . . . . . . . . . . .
USB to serial box . . . . . . . . . . . . . . . . . . . . .
AgGPS FmX integrated display . . . . . . . . . . . .
GreenSeeker sensors . . . . . . . . . . . . . . . . . . . . . . .
Product rate controller . . . . . . . . . . . . . . . . . . . . .
GPS receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Field preparations for nitrogen application . . . . . . . . .
Field information . . . . . . . . . . . . . . . . . . . . .
Setting up the field . . . . . . . . . . . . . . . . . . . .
Field preparations for user-defined rates (custom table)
Installing the RT Commander software . . . . . . . . . . .
3
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
18
19
20
21
22
23
23
24
25
25
27
28
28
28
29
30
32
Configuration and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Starting the RT Commander software . . . . .
Setup and configuration . . . . . . . . . . . . . .
Logging options . . . . . . . . . . . . . . .
Communication port assignments . . .
GPS receiver communication setup . .
Rate controller communication setup.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
34
35
35
35
35
37
9
Contents
RT200 interface module communication setup .
Variable rate application setup. . . . . . . . . . . . . . . .
Collecting Reference Strip data . . . . . . . . . . .
Mapping with the user interface. . . . . . . . . . . . . . .
Data output. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic tools . . . . . . . . . . . . . . . . . . . . . . . . .
Status tab. . . . . . . . . . . . . . . . . . . . . . . . .
Errors tab . . . . . . . . . . . . . . . . . . . . . . . . .
Comm View tab. . . . . . . . . . . . . . . . . . . . .
Data management . . . . . . . . . . . . . . . . . . . . . . .
Application information . . . . . . . . . . . . . . . . . . . .
Delivery system and liquid control . . . . . . . . .
Selecting a nozzle. . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
38
39
40
43
44
45
45
45
46
46
47
47
48
48
A
Cable Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
B
Custom Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Custom Formula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
10
CHAPTER
1
Introduction
In this chapter:

System overview

Definitions of terms

Care and maintenance

Resources

GPS

Technical assistance

Your comments
1
This manual describes how to install and operate
the hardware and software for the Trimble®
GreenSeeker® RT200 system.
11
1
Introduction
System overview
The GreenSeeker RT200 variable rate application and mapping system is a tool for
variably applying agricultural chemicals based on real-time measurements of the crop.
The sensors measure NDVI (Normalized Difference Vegetation Index) of the plants
while traversing the field, and the software collects the data that can be used to
generate maps of the NDVI and rates (where applicable) for crop analysis and
historical data collection. This type of data can be used in conjunction with other
agronomic references to index nutrient response, crop condition, yield potential,
stress, pest, and disease impact in a quantitative manner. The RT200 system can be
used to monitor changing crop conditions during the growing season and the effects of
different levels of an input compared to a defined standard.
The applicator allows you to variably apply agricultural chemicals in real time (as the
applicator passes over the crop). The NDVI-based variable rate algorithm and
parameters may be selected in the field, and all rate changes are then made "on the go,"
so there are no lengthy delays between evaluating the crop and application. When
applying fertilizer or other material, the NDVI, the target rate on, and the applied rate
are mapped simultaneously with the GreenSeeker RT200 system. Some spray
controllers do not respond with an 'As Applied' value.
The GreenSeeker optical sensor emits light at two specific wavelengths, and measures
the reflected light. The microprocessor in the sensor analyzes the reflected light and
calculates the resulting Index value. The data from each sensor is collected by the
RT200 interface module, processed and then transmitted to a PDA in the cab running
one of the following:
•
RT Commander software
•
Version 3.0 or later of the AgGPS® FmX® integrated display
The RT Commander software displays the NDVI and location in real-time, logs the
output data to a file, and sends the appropriate rates to the applicator's rate controller
or FmX integrated display. The logged data is easily transferred to a desktop computer
for analysis.
The ruggedized PDA (Personal Digital Assistant) could be a Trimble Recon® or
Nomad® handheld computer. In this document, “PDA” refers to both handheld models:
If anything refers to only one model, this is clearly indicated.
12
1
Introduction
Definitions of terms
The following terms occur throughout this manual and in the RT Commander
software. Becoming familiar with the terms will make using the RT Commander
software much easier.
CAN
Controller Area Network.
A high-integrity data communications bus for real-time applications that operates at data
rates of up to 1 Megabit per second, and has excellent error detection and confinement
capabilities
GDD
Growing Degree Days.
Some GreenSeeker algorithms use this value as an input to determine expected plant
growth stage. For more informaiton, see "Where to Find GDD Information" at
http://www.greenseeker.com/software/.
GPS
Global Positioning System.
A system using satellites, receivers and software to allow users to determine their exact
geographic position.
N
Nitrogen fertilizer
NDVI
Normalized Difference Vegetation Index.
Commonly used to measure plant health and vigor.
NDVI = (NIR_reflected Red_reflected)/(NIR_reflected + Red_reflected).
NUE
Nitrogen Use Efficiency.
A percentage of nitrogen taken up by the plant. For example, an NUE of 60% means that 6
lbs. of nitrogen fertilizer is expected to be used by the plant that year for every 10 lbs.
applied. For more information, see www.nue.okstate.edu.
NRS
Nitrogen Rich Strip.
This reference strip/area determines the amount of nitrogen being made available to the
plant by the environment (mineralization, and so on), and importantly the present year's
expected maximum yield potential and response to additional nitrogen.
PDA
Personal Digital Assistant. See User Interface.
RI
Response Index.
Provides an indication of how the crop will respond this season to additional N.
User Interface
A portable hand held computer.
Typically, a ruggedized PDA such as a Trimble Recon or Trimble Nomad handheld computer.
VI
Vegetation Index.
A value that is calculated (or derived) from sets of remotely-sensed data that is used to
quantify plant health, stress, and vigor.
VRA
Variable Rate Application.
Based on information supplied to a rate controller, the rate of fertilizer or other chemical
applied.
Care and maintenance
C
WARNING – There are no field serviceable components of the electronic system; do not
attempt any field repair of a malfunctioning controller or sensors. If you experience
operating problems, contact your local reseller, representative, or GreenSeeker distributor
for assistance.
13
1
Introduction
You must take good care of your GreenSeeker RT200 variable rate application and
mapping system to maintain high performance. At the end of each day of spraying, do
the following:
•
Check the detector and light source windows for dust and dirt, and wipe clean
with a soft rag.
•
Do not leave the GreenSeeker systemoutdoors during extreme weather
conditions. Wide temperature variations may reduce the operating life of the
system.
•
Do not store a GreenSeeker system with the sensors facing upward. Doing so
may allow water to collect around the windows and gaskets, causing seal
failures in those areas. Direct sunlight can in some cases also focus enough
energy into the sensor to damage the detector.
•
When rinsing off the machine, take care not to use high pressure to directly
spray the sensors. Even though all connectors and modules are fully sealed,
there still exists potential leakage from a pressurized stream.
•
Every time the spray tank is filled, take a soft cloth and wipe the lenses of the
sensors if needed. Try to check sensors at least once a day during full-time
operation.
•
Be more aware of cleaning the sensors directly behind the machine.
•
If you do not have ground protection devices on the boom, such as gauge wheels
or skids, take extra care to not run the boom into the ground. Also, be aware of
sensor vulnerability to stationary structures in the field. Sensors are usually
mounted on the front of the boom and do not have rigid protection.
•
Rinse the boom after the end of every day. This will keep the system clean and
wash any corrosive materials off. This will greatly extend the life of your
machine.
•
At the beginning of each season, and periodically as required, check the hose
clamps, plumbing connections, and other fluid handling system components for
tightness and leak free operation.
•
Make sure all wiring harness components remain fastened to the boom as to not
obstruct the view of the sensors and are free of any pinch points from boom
folding and movement.
Resources
PDA support: Tripod Data Systems
http://www.tdsway.com/support
Tel: 720-587-4700
14
1
Introduction
Other resources
Nitrogen Use Efficiency, www.nue.okstate.edu
Sensor-Based Nitrogen Rate Calculator,
www.soiltesting.okstate.edu/SBNRC/SBNRC.php
GPS
Even if you have used other Global Positioning System (GPS) products before, Trimble
recommends that you spend some time reading this manual to learn about the special
features of this product. If you are not familiar with GPS, visit the Trimble website
(www.trimble.com) for an interactive look at Trimble and GPS.
Technical assistance
If you have a problem and cannot find the information you need in the product
documentation, contact Trimble technical support:
1.
Go to the Trimble website (www.trimble.com).
2.
Click the Support & Training link at the top of the screen, select Support and
then select Support A‚ÄìZ list of products.
3.
Scroll to the bottom of the list.
4.
Click the submit an inquiry link. A form appears.
5.
Complete the form and then click Send.
Your comments
Your feedback about the supporting documentation helps us to improve it with each
revision. Email your comments to [email protected].
15
1
16
Introduction
CHAPTER
2
Installation and Setup
In this chapter:

System layout with the Trimble
Recon handheld

System layout with Trimble
Nomad handheld

System layout with Trimble AgGPS
FmX display

Cables

RT200 interface module

User interface

GreenSeeker sensors

Product rate controller

GPS receiver

Field preparations for nitrogen
application

Field preparations for userdefined rates (custom table)

Installing the RT Commander
software
2
This chapter describes the system layout and
installation of the GreenSeeker RT200 system
components.
17
2
System layout with the Trimble Recon handheld
18
2
System layout with Trimble Nomad handheld
19
2
System layout with Trimble AgGPS FmX display
Power switch
g
c
k
f
h
j
d
e
i
l
m
l
m
m
m
GreenSeeker
sensors
Item
20
Description
Trimble part number
c
FmX integrated display
93100-01
d
e
f
g
h
i
j
k
l
m
FmX power cable
66694
FmX basic power cable
67258
8 m GPS TNC/TNC RT angle cable
50449
Ag25 GNSS antenna
68040-00S
FMX / FM-1000 to CAN w/port replicator cable
75407
Cable Assy, GreenSeeker to Display
77704
900-1-047
30' RT200 power cable
400-1-276
20' RT200 interface module cable
400-1-277
20' RT200 sensor cable
400-1-265-240
2
Cables
Before mounting sensors, loosely route cables on the machine:
•
Route all cables in areas where protection from mechanical movement can be
assured.
•
Do not kink any of the cables. You must allow at least a 6-inch (15 cm) bend
radius in all cables.
•
Once cables are routed and all hardware is mounted, final placement of cables
can be made.
•
Finalize by securing cables with tie wraps, zip ties, and so on as required.
Cable placement is as follows:
Cable number
Cable description
Placement
400-1-278
RT200 interface
module to a Recon
handheld
Connect the Recon handheld and interface module:
• Connect the cable end with the DB9 connecter to the Y-cable
connector marked "Port 1" on the handheld. See the vehicle's
manual for cab access holes—most cabs have auxiliary access holes
available.
• Route the other end of this cable to the RT200 interface module,
see page 18.
RT200 interface
module to a Nomad
handheld
Connect the Nomad handheld and interface module:
• Connect the cable end with the DB9 connecter to the USB to serial
box connector marked "RT200 I/M COMM 5". See the vehicle
manual for cab access holes; most cabs have auxiliary access holes
available.
• Route the other end of this cable to the RT200 interface module,
see page 19.
400-1-265-240
Sensor cables
Place cables between the outer two or three sensors on each side of
the boom. These cables connect the sensors in a “sensor chain”. For
appropriate sensor placement, see GreenSeeker sensors, page 25.
400-1-277
Sensor to interface
module cables
Connect the two innermost sensors to the interface module. The
sensors “daisy chained” on the left side of the boom must connect to
the port labeled Left CAN Bus, and the sensors on the right side must
connect to the port labelled Right CAN Bus. For hardware placement,
see RT200 interface module, page 22 and GreenSeeker sensors,
page 25.
77704
"T" cable
Connected between one of the 400-1-277 cables and the interface
module, the long part of this cable connects to the FmX integrated
display on Port A or Port B.
400-1-276
Power cable
This cable provides 12 VDC power to the system:
• Connect one end to the interface module.
• Connect the other end to battery power.
Do the following to install the inline toggle switch that is provided to
control system power:
1. Mount the switch in the required location in the cab.
2. Splice the toggle switch into the red wire (+12 V) that is included
with the cable.
Note – Some vehicles may provide battery power terminals in the
cab. A minimum of 11.4 V is required to operate the system.
21
2
Cable number
Cable description
Placement
400-1-066
Serial cables with
standard female
DB9 connectors
Connect the PDA to the GPS and rate control modules in the cab.
Note – Some GPS units and rate control modules may require a null
modem or gender change adapter. Refer to the manuals for the GPS
and rate controller for proper connections (if either module requires
a null modem connection to a desktop computer then it will also
require one to be connected to the Recon). Null modem cables and
adapters are available from most electronic stores.
Power adapter cable Provided with each PDA. It contains a voltage converter/regulator to
provide the correct charging voltage.
C
WARNING – Do not remove/cut or bypass the auto adapter
end of the power adapter cable for the PDA. Do not connect
directly to 12 V DC as this will cause immediate failure of the
PDA.
For emergency repair and troubleshooting purposes, see Appendix A, Cable Diagrams.
These diagrams are provided for use by qualified technicians only.
The RT200 interface module contains
circuitry to interface boom-mounted sensors
with the user interface. The interface module
has serial, CAN, and power connections. It is
an environmentally sealed enclosure that can
be installed inside or outside the cab.
Mount the module in close proximity to the
center of the boom-mounted sensors (check
the length of cables 400-1-277 and 400-1-278
for suitable placement).
There are two small indicator lights on the lid.
The interface module has mounting brackets with drilled holes for mounting.
22
1.
Mount the module in a structurally safe location on the machine. Trimble
recommends that you mount the module with connectors facing down to avoid
water in the connectors. An additional bracket may need to be made.
2.
After the enclosure is mounted, connect cable 400-1-276 to the 12 V DC port.
You must fully rotate (approx ¼ turn) the gray retaining nut on the connector
into the locked position.
3.
Connect cable 400-1-277 (this goes to the innermost sensor on the right boom)
to the port labeled Right CAN Bus.
4.
Connect the second cable 400-1-277 (this goes to the innermost sensor on the
left boom) to the port labeled Left CAN Bus.
5.
If using a PDA, connect cable 400-1-278 to the connection port labeled Serial
Port.
2
Note – Be careful not to loosen the black strain relief portion of the connector when
connecting or disconnecting.
Note – If you are using the FmX display, the serial port is not used. Install the cable port
cap to protect this port:
User interface
Ruggedized PDA
The RT200 system includes a ruggedized PDA that is powered by a Windows Mobile®
operating system and that is pre-loaded with the RT Commander software.
•
The Recon handheld uses 3 serial ports through a CF-to-2-port serial splitter.
•
The Nomad handheld uses a USB-to-4 port serial converter.
Note – In this document, “PDA” refers to both handheld models: If anything refers to only
one model, this is clearly indicated.
A removable memory card is supplied and pre-installed in the PDA for easy data
transfer; alternatively, connect the PDA to a desktop computer for data transfer.
23
2
An adjustable mount is provided that allows you to easily mount and remove the PDA
in the cab. Place it where the operator can easily view it and select the buttons:
1.
Assemble the entire mounting structure before mounting the base. Verify that
the mounting location allows for cable connections to the PDA (the bottom
and/or top as required by the specific PDA).
2.
Mount the base securely in the cab and then place the PDA in its clip mount.
Snap the PDA into place until secure:
Recon handheld
Nomad handheld
Note – See also the corresponding System Layout diagrams: System layout with the
Trimble Recon handheld, page 18 and System layout with Trimble Nomad handheld,
page 19.
3.
C
To keep the PDA’s battery charged, plug the auto-adapter power cable (included)
into an available 12 V DC outlet in the cab.
WARNING – Do not remove/cut or bypass the auto adapter end of the power adapter
cable for the PDA. Do not connect directly to 12 V DC as this will cause immediate failure
of the PDA.
Note – The auto adapter for the Recon and Nomad handhelds are not interchangeable.
4.
Once all the cables are connected, secure the cables in the cab to avoid damage
to the cable.
USB to serial box
This box is used for all systems that use the
Trimble Nomad handheld. It converts the USB
port at the bottom of the handheld into four
DB9 serial ports.
24
2
AgGPS FmX integrated display
Version 3.0 or later of the FmX integrated
display has a large color touchscreen and
integrated GPS and GLONASS receivers
for complete guidance, steering,
mapping, and application control.
The GreenSeeker plugin shows and stores
the data from the sensors, and
communicates with the applicator's rate
controller. The GreenSeeker plugin and
VRA unlock code are required to unlock
the GreenSeeker function on the display.
The FmX integrated display is not packaged with the GreenSeeker RT200 system. For
more information, see the AgGPS FmX Integrated Display Installation Instructions and
the AgGPS FmX Integrated Display User Guide.
GreenSeeker sensors
C
CAUTION – GreenSeeker sensors are designed to operate in harsh environments. The
sensor enclosure and connections are environmentally sealed. Although the sensor is
sealed, DO NOT wash the sensor directly with a high pressure washer. To clean the sensors,
use low pressure and gentle washing procedures.
The sensor takes reflectance readings. The units generate their own illumination for
use in any lighting condition, day or night. When the unit is on, a red band of light
shows directly below the rectangular sensor window.
The sensor operates by emitting light from the rectangular window onto a crop's
canopy. Reflected light from the canopy is focused on a detector behind the circular
window:
•
Both the rectangular and circular windows need to be free of any viewing
obstructions when mounted.
•
Mount the sensor so that there is at least 12'' (0.3 m) in front and 6'' (0.15 m) in
back of the lenses' peripheral view.
•
Keep at least 12'' (0.3 m) for the peripheral side view of the sensor free of objects.
The sensor is designed for an optimal height of 28'' to 48'' (0.7 m to 1.2 m) from the
rectangular LED window to the crop canopy. The extended range (with greater
deviation) is 26'' to 62'' (0.6 m to 1.6 m). The field of view (the width of the sensor
measurement) is ~24'' (0.6 m) within the sensor's optimal height range.
Sensor readings are nearly constant with the optimal height range, but will vary
somewhat over the extended range. Momentary movement out of the operating height
range does not significantly affect performance of the RT200 system, but take care to
keep sensors within the recommended height range most of the time.
25
2
Mounting the sensors
26
•
Sensors are typically mounted using the standard
stainless steel bracket (provided). These
brackets are designed to fit most boom
structures.
•
The two outer sensors will have only one cable connected. The other port in the
outer sensors must be electrically terminated using a small plug device called a
CAN terminator. (The CAN terminator is usually pre-installed in two sensors.)
Mount these sensors in the outside (end) positions.
•
The bracket can be secured to most boom structures with standard size U-bolts.
One set of U-bolts is included with the system. Some booms may require
different U-bolts and/or custom fabricated brackets.
•
The sensor is bolted to the bracket with two 5/16" bolts (provided).
•
Sensors can be mounted in front of or behind a boom. The "direction" of the
sensor is not important, but the rectangular LED window must be parallel to the
applicator boom:
2
•
For crops such as wheat and canola, the RT200 system works best when sensors
are evenly spaced across the swath of the boom. For example, if a boom is 60 feet
wide then the sensors would be spaced approximately 10 feet apart and the
outer two sensors would be spaced approximately 5 feet from the tips. Boom
folding procedures may prevent even spacing of sensors. This is acceptable as
long as the sensors are spread across the boom as evenly as possible. For row
crop applications, sensors must be positioned directly over a row. When used in
fields with a "guess row" or "wide and narrow row" you may have to mount the
sensor within your planter width.
•
Once the sensors are mounted, connect the sensor cables (400-1-265-240) as
shown in the system layout figure:
•
a.
These cables have a 12-pin connector on each end. Slide the connector into
one of the ports on the sensor with the keyed side towards the front of the
sensor.
b.
After firmly seating the connector, use a Phillips screwdriver to secure the
connectors retaining ring. It does not matter which port the 400-1-265-240
cables are connected to. The two outer sensors will have only one cable
connected. The other port in the outer sensors must be terminated.
c.
Insert the terminator (if not already installed) in the unused port of the
outer sensors and then secure the retaining ring.
As described in previous sections, use the 400-1-277 cables to connect the two
inner sensors to the interface module in the same way used for the
400-1-265-240 cables. Once all cables are connected, secure the cables to the
boom. Verify that cables will not be damaged by moving parts.
Product rate controller
Most applicators come with an installed product rate controller. The RT200 system
interfaces with most available controllers. If you have a rate controller that is not
currently supported by the RT Commander software, contact Trimble or your dealer to
inquire about obtaining support.
27
2
GPS receiver
A GPS receiver is necessary for logging geo-referenced data and viewing on-the-go
mapping. An applicator may already use a GPS receiver for other operations such as
guidance. In many cases it can be shared. The RT200 accepts a serial connection
(RS-232) from a GPS receiver to the ruggedized PDA through a serial-to-USB converter.
Field preparations for nitrogen application
Field information
Before the GreenSeeker applicator can be used to apply nitrogen (N) across a field, you
must establish a nitrogen rich reference strip (NRS) before or shortly after planting.
This reference strip determines the amount of nitrogen being made available to the
plant by the environment mineralization and importantly, the present year's expected
maximum yield potential and response to additional nitrogen. The ideal NRS runs the
length of the field, but it should at least be 300 feet (91 m) long. Establish the NRS in a
representative portion of the field (that is, not in a high or low spot). The rate of N
necessary to establish a NRS depends on the crop and region, and should be equivalent
to the highest rate necessary to satisfy crop needs throughout the growing season. For
example, winter wheat grown in the Southern Great Plains should have a minimum of
100 lbs N/acre applied to establish the NRS. Lower pre-plant N rates should be applied
across the rest of the field. Application of 20 to 30 lbs of pre-plant N/acre would be
ideal for this situation.
The rest of the field is referred to as the Non-Reference (Non-Ref) portion. It may also
be referred to as the N-limited area or farmer practice region.
For best results, use the RT200 interface module to "read" the NRS and apply N at
growth stages dependent upon the crop algorithm used. For Trimble-supplied
algorithms the following is typically:
•
Wheat: Feekes growth stage 4-6
•
Corn: V8-V12.
For the sensors to accurately determine NDVI for topdressing (or sidedressing), plant
coverage should be at least 50%. The RT200 system with RT Commander can use the
sensor mounted booms to read the NRS, or the GreenSeeker handheld sensor can be
used to determine field conditions.
To collect sensor readings for the NRS, pass the boom-mounted sensor (or handheld
sensor) over the crop at 32'' to 48" (81 cm to 122 cm) above the canopy. Sense a large
area of the NRS and non-reference portion of the field to accurately determine their
respective NDVI values. Once you have measured the NDVI values, enter them into the
RT Commander software. You can do this automatically with the boom-mounted
sensors, or manually with the GreenSeeker handheld sensor. The RT Commander
software and the RT200 system allows for "straddling" the edge of the NRS and using
28
2
either the right side or left side of the boom for reading the respective areas, for
example, with three sensors over the NRS and three over the rest of the field. You can
also use the complete boom (with all sensors) to "read" NDVI in each area separately.
If response is obviously variable across the field, select an area where the difference
between the Reference and the Non-Reference areas are most apparent. This ensures
that the algorithm determines a rate that uses the highest yield potential prediction
and maximum response to N for that year.
To estimate yield potential, an environmental factor (Growing Degree Days) is used,
which takes into account weather and time since planting.
Note – Different GDD variations are used for different crops. To obtain the GDD value, you
need the planting date and sensing date. Regional values for GDD are available on the
Internet. For more information, see Where to Find GDD Information at
http://www.greenseeker.com/software/.
Setting up the field
1.
2.
Decrease the pre-plant Nitrogen (N) application rate of the field to a level at least
half of previous total N applied during non-GreenSeeker management practice:
–
For spring or winter wheat, if the application rate has historically been 100
lbs N/acre, decrease the rate to 50 lbs N/acre.
–
For corn, if application rates have historically been 200 lbs N/acre, decrease
the rate to 75 to 125 lbs N/acre.
Prior to or shortly after planting, establish the NRS (Nitrogen Rich Strip) in a
representative portion of the field (that is, not in a historically high or low spot).
Apply an applicator’s width swath of N. The rate of N applied should be high
enough to satisfy crop N needs in a good year:
–
For spring or winter wheat, the N rate should be at least 100 lbs N/acre.
–
For corn, the N rate should be at least 200lbs N/acre.
Use a marker to ensure that you can easily find the NRS later in the season.
The ideal NRS runs the length of the field, but it should at least be 300 ft (91 m)
long.
3.
At the appropriate crop growth stage, take readings of the NRS and an adjacent
part of the field to be fertilized. For the supplied algorithms the following is
typical:
–
Wheat: Feekes growth stage 4-6.
–
Corn: V8-V12.
4.
Find the area where the nitrogen rich strip is most apparent in comparison to
the rest of the field (this indicates greatest potential for the crop).
5.
Take sensor readings with the RT200 system or a handheld sensor to input to
the selected crop algorithm.
29
2
6.
Match nozzles and/or rate control system to maximize response time and
performance for each field's requirements. For more information, see Delivery
system and liquid control, page 47. Also refer to the application equipment and
rate control systems manuals.
Field preparations for user-defined rates (custom table)
Example: Cotton Defoliant
The RT200 system can be used to apply materials other than Nitrogen. The RT200
software permits a custom algorithm to be entered; this is a table of product values
compared to NDVI. A table has 16 points corresponding to an NDVI range of 0.25 - 0.88.
These values are entered directly on the RT Commander software screen (select Crop
Algorithm / Custom Formula).
Note – In RT Commander software version 1.3.x and later, there is also a high-resolution
100 point table option for NDVI values from 0.00 - 0.99. All points must have a value
entered.
Growers or crop consultants have historical crop knowledge that enables them to
determine different crop input requirements based upon biomass/size of the
crop/plant, for example, the variable rate application of defoliant in cotton. If this is the
case, the field is scouted or "field calibrated" to determine areas of the field that require
different rates of defoliant. The RT200 system or a GreenSeeker handheld sensor is
used to obtain the NDVI values in representative areas of the fiel, In the following
figure, the NDVI of the crop was measured under particular conditions for which the
grower knew the approximate required rate, using the GreenSeeker handheld sensor:
A table is then created with NDVI values corresponding to application rates. These
values are entered into the Custom Formula application table. See Appendix B, Custom
Algorithm.
30
2
The following table (and the resultant Calibration Graph) is an example for defoliant
variable rate application in cotton:
These values are only an example; the grower/consultant must develop these rates.
Also keep the rate range ability of the specific rate controller and nozzles used to
achieve these rates in mind when developing the rates.
To use the Custom Formula feature, you must enter some required values as shown
below. The default is zero; enter a value ( for example, 1) in the Non-Ref, Ref and RefPeak, and the GDD fields and then tap OK:
31
2
Installing the RT Commander software
An update procedure is available for installing or updating RT Commander software at
http://www.greenseeker.com/lit/gs/RTCommander_Update_Procedure.pdf
Also use these instructions if the PDA has lost its charge, has had to be hard reset, or if
you need to install the factory installed software and drivers on a new PDA.
1.
Connect the PDA to a computer using Microsoft ActiveSync technology or the
Windows Mobile Device Center (if the computer is running the Windows Vista®
operating system).
2.
Once the ActiveSync technology indicates that the PDA is connected, insert the
RT Commander CD into your computer.
3.
Click Start | Run. When the Run window appears, enter
D:\RT Commander\Install.exe (where D:\ is the CD drive).
4.
Follow the on-screen instructions to complete the installation.
5.
To soft reset the PDA, hold down the power button for about 8 seconds.
6.
If you are prompted to enter a registration number after running the program
for the first time, register your software at www.greenseeker.com/register/.
A registration number will be emailed to you.
If you need additional help, contact your reseller.
32
CHAPTER
3
Configuration and Operation
In this chapter:

Starting the RT Commander
software

Setup and configuration

Variable rate application setup

Mapping with the user interface

Data output

Diagnostic tools

Data management

Application information

Troubleshooting
3
This chapter describes how to configure and use
the system.
The RT200 system can be used with either
version 3.0 of the FmX integrated display, or with
a PDA. This document describes the system
using a PDA; for information on the FmX
operation, see the Greenseeker chapter in the
AgGPS FmX Integrated Display User Guide.
The software interface of the RT200 system is the
RT Commander software or version 3.0 or later of
the FmX integrated display. The RT Commander
software was developed for use with a ruggedized
PDA powered by a Windows Mobile operating
system. Typically, RT200 systems are supplied
with a ruggedized PDA.
The software provides an interface where you
select setup features and enter operating
parameters. It can also display the current
system status and data logging capabilities. For
more information, familiarize yourself with the
PDA’s operating instructions.
This manual describes version1.3.x of the RT
Commander software. The operation is the same
as for version 1.2. However, additional
diagnostics functions and more options for
custom algorithms have been added.
33
3
Starting the RT Commander software
1.
Turn on the RT200 interface module, GPS, and rate controller (if applicable).
The RT200 green Power LED blinks three times, accompanied by three beeps
when it is first turned on. The Status LED will then blink corresponding to each
transmission of sensor data over the CAN bus. You will see a brief green flash,
followed by a red flash at the I/M message rate (typically at 0.5 sec), indicating
data from the Left and Right CAN ports, respectively.
2.
Turn on the PDA. When it starts, you may hear two separate "new hardware"
chimes:
–
The first chime indicates that the CF-to-Serial device is detected.
–
The second chime marks the initialization of the two additional COM
ports.
If no chimes are heard after the first five seconds, your PDA does not have the
chimes feature. If this is the case, wait at least 10 seconds before opening any
applications.
Do not launch the RT Commander software until you have heard both chimes
or until at least 10 seconds have passed.
34
3.
Select Start / Programs.
4.
Tap RT Commander. The RT Commander startup
screen appears.
3
Setup and configuration
The RT Commander software communicates with up to
three devices: the GPS receiver, the rate controller, and
the RT200 interface module.
You usually need to configure these devices only once as
the software retains the settings. You need to update the
setup parameters if new equipment is used with the
system.
Note – If you plan to only collect GreenSeeker sensor data
for mapping, you may skip the Controller section of the
setup.
Logging options
The Recording Interval is the rate at which data points are
written to the file. It defaults to 1000 ms (1 second) and
should always be less than or equal to the GPS rate.
Communication port assignments
Nomad handheld
Recon handheld
RT200 data
COM 5
COM 2 (Port 1)
GPS
COM 6
COM 3 (Port 2)
Rate controller COM 7
COM 1 (built in)
GPS receiver communication setup
The RT Commander software is configured to accept GPS data in NMEA 0183 format
(industry standard). The minimum NMEA messages necessary to acquire a valid GPS
coordinate are GGA and VTG or GGA and RMC.
Most GPS receivers are configured to output these messages by default and no
additional programming or configuration is necessary. For more information, see your
GPS receiver manual.
1.
Select Setup (at the bottom of the main screen) and then tap GPS Setup.
35
3
2.
Select GPS on COM Port.
GPS simulation is for troubleshooting only.
3.
Tap the Comm tab.
4.
Verify that the correct COM Port is selected. For
settings, see Communication port assignments,
page 35.
5.
Configure the COM settings to match the output
specifications of your GPS receiver—values shown
here are typical.
For exact settings, see the GPS unit's manufacturer
defaults.
6.
Tap OK.
7.
Check the status bar to confirm that a valid GPS
coordinate appears after you enter the settings.
Note – If you open a job before acquiring a valid GPS
location, you may not see data on the mapping screen.
36
3
Rate controller communication setup
1.
Select Setup (at the bottom of the main screen) and then tap Rate Controller
Setup.
2.
The RT Commander software can communicate
with several brands and models of rate controllers.
For more information, refer to the Compatible Rate
Controllers list:
http://www.greenseeker.com/pdf/Compatible%20
Rate%20Controllers.pdf.
To create a new setup, tap New.
3.
In the Setup Description field, enter a description of
the equipment and/or controller. For example, rav1
(and may be for a RoGator 854 with Raven 440).
You usually need to create this configuration only
once, unless you move the RT200 to other
equipment.
4.
From the Type drop-down field, select the
controller brand/type .
5.
options, see Communication port assignments,
page 35.
6.
Tap the Controller tab and verify that the
controller's specifications match the options
shown. These specifications and screen options are
different depending on the selected controller
brand.
7.
Tap OK.
37
3
RT200 interface module communication setup
1.
Select Setup (at the bottom of the main screen) and then tap RT200 Setup.
2.
options, see Communication port assignments,
page 35.
3.
From the Selected V.I. drop-down list, select the
index. The default (and most likely choice) is NDVI .
When you select an algorithm in the Measure
Parameters screen, this value changes
automatically as appropriate for the algorithm.
Note – Custom tables will not change the value you select
here.
38
4.
In the Update field, enter the frequency at which
sensor data is sent to the RT Commander software.
The interval should be about half of the GPS
update interval at lower rates and equal to the GPS
interval at higher rates:
1 Hz update: 495 ms (~2 Hz)
2 Hz update: 245 ms (~4 Hz)
5 Hz uUpdate: 200 ms (~5 Hz)
5.
In the Data Format field, select RT200. This must
be used to log sensor data and perform variable
rate application using sensor readings. The other
options are to create simulated data for
troubleshooting only.
6.
Tap OK.
3
Variable rate application setup
The RT200 system enables you to apply variable amounts of nitrogen in real-time
based on the condition of the crop.
1.
Tap New Application Job or Open Existing Job.
2.
From the Field Name field, select an existing field or
select Add/Edit fields.
The File Name is created automatically in the
format A (application file), current date (ddmmyy),
and the field at the end of the file name. Tap the
browse icon to change the file location to which
the file will be saved. For more information, see
Data management, page 46.
3.
To check the configuration, tap the Config button
next to the device.
4.
In the Swath Width field, enter the swath width of
the applicator for the mapping screen display.
5.
Tap OK. The Select Measurement Method screen
appears.
You can now collect reference strip data.
39
3
Collecting Reference Strip data
1.
Do one of the following to collect and/or input the reference strip data:
–
Use the GreenSeeker handheld sensor before
application to read the reference strip:
a.
Tap the From GreenSeeker Handheld option.
b.
Enter the data that you collected previously.
When you tap the required field, a numeric
keypad appears.
Note – You must enter the Ref-Peak value and this must be
equal to or greater than the Ref value.
2.
40
–
Use the boom-mounted sensors on the RT200
system
a.
To “read” the reference strip, do one of the
following:
–
Tap the Simultaneous Ref Strip & Non-Ref
Strip option and then "straddle" the edge
of the reference strip with the left or right
side of the boom over the reference strip.
Once over the appropriate area, tap Go to
collect data; tap Stop when finished.
This populates the required fields in real
time
If required, repeat this procedure to
ensure correct readings.
–
Tap the Drive Calibration Reference Strip option to read the reference
strip. Tap Go to collect data; tap Stop when finished. This populates
the Ref and Ref_max fields.
Tap the Drive Non Reference Area option to read the reference strip.
Tap Go to collect data from the non-reference strip (area to apply to);
tap Stop when finished. This populates the NonRef-Min and Non-Ref
fields.
If required, repeat this procedure to ensure correct readings.
Tap OK to continue to the next screen.
3.
The reference data is transferred to this screen. To
change the values if required, tap Edit.
4.
Select the appropriate crop algorithm or select to
create a custom application rate table of your own
from the Crop drop-down list. To use a custom
table as your algorithm, see Appendix B, Custom
Algorithm.
5.
Most crop algorithms require you to enter a value
for GDD (Growing Degree Days). For some crops
this will be Days From Planting.
6.
For fertilizer, select NUE (Nitrogen Use Efficiency).
The default depends on the Algorithm selected in
Step 4.
7.
Select Liquid or Granular, and enter the %N by
weight.
8.
Enter Min and Max settings to limit the rate
commands given to the rate controller if required.
Use these for nozzle and or application system
limitations.
9.
If you have a second boom that will be operated at
a flat rate ( for example, a herbicide injection
system that uses UAN for carrier fluid), select the
Dual Booms check box and then enter a Fixed rate
value.
3
10. To display the actual application graph for the
specific sensor to rate commands, tap Show
Graph .
a.
Review the application graph for each field to
determine the required nozzle selections
and/or application equipment settings.
Note – If you use the RT200 sensors for variable rate control,
you must set up the application equipment and rate
controller to match the expected delivery rate commands.
For more information, see Application information, page 47.
b.
Select other units as required for the
material/delivery system of your sprayer from
the Units drop-down list.
41
3
11. Tap OK. The Apply to an Area screen appears. The
field name is shown in the upper left corner (in this
example, N 40).
12. With your application system and rate controller
ready to perform VRA, tap Go and begin applying.
Tap Stop when finished.
13. Your progress in the field is shown on the screen,
along with sensor values, target application rates,
and as applied rates received back from the rate
controller.
GPS is shown in the Status bar—tap this area to
open the Status screen (see page 45) appears.
Tap Stop to stop logging and rate commands. Use
the existing boom controls to stop application of
material.
14. Once you complete the job, do one of the following:
42
–
To start a new job, tap File and then select
Close Job .
–
To exit the program, tap File and then select
Exit.
3
15. Tap Yes to accept the confirmation message. The
progess bar shows the progress of creating a shape
file to allow mapping of your data. Depending upon
how long you worked, this could take several
minutes.
Note – From version 1.3.6, data is written to the file
incrementally, so closing happens within 3 seconds.
Mapping with the user interface
The RT200 system enables you to map vegetation characteristics for crop analysis and
historical data collection.
1.
Tap New Application Job or Open Existing Job.
2.
From the Field Name field, select an existing field or
select Add/Edit fields.
The File Name is created automatically in the
format M (mapping file), current date (ddmmyy),
and the field at the end of the file name. Tap the
browse icon to change the file location to which
the file will be saved. For more information, see
Data management, page 46.
3.
To check the configuration, tap the Config button
next to the device.
4.
In the Swath Width field, enter the swath width of
the applicator for the mapping screen display.
43
3
5.
Tap OK. The Map an Area screen appears. The field
name is shown in the upper left corner (in this
example, N 40).
6.
Your progress in the field is shown on the screen.
GPS is shown in the Status bar. Tap this area to
open the Status screen (see page 45).
Tap Stop to stop logging.
7.
Once you complete the job, do one of the following:
–
To start a new job, tap File and then select
Close Job .
–
To exit the program, tap File and then select
Exit.
8.
Tap Yes to save application data or tap No to resume data collection.
9.
The progess bar shows the progress of creating a
shape file to allow mapping of your data.
Depending upon how long you worked, this could
take several minutes.
Note – From version 1.3.6, data is written to the file
incrementally, so closing happens within 3 seconds.
Data output
The data from the GreenSeeker sensors is collected by the RT200 interface module
over the CAN bus, and then output as ASCII text in RS-232 format (38, 400, 8, N, 1) to
the RT Commander software that is running on the PDA.
At each sample interval, the data is transmitted based on the selected options for the
RT200 system. In particular, each line of data includes the value of NDVI and the value
for a second VI chosen by the user.
44
3
Diagnostic tools
To view the Status screen, tap Task and then tap Show Status. The screen has three
tabs.
Status tab
This shows the following details. Data here indicates
positive communication to these devices.
•
GPS detail status.
•
RT200 Sensor status. This includes the number of
sensors detected on system and error reporting.
The RT200 system monitors the sensors for correct
operation, and if a sensor reports erroneous data,
the data is not included in the rate control
calculation. Incorrect data can come from mud on
the sensor lenses, sensors viewing concrete, snow,
wet asphalt, or other non-soil or plant surfaces. The
Sensor Errors field reports the number of sensors
reporting NDVI out of expected values. For more
information, see Data output, page 44.
•
The RT200 interface module hardware and
software version report. This also confirms that the
interface module and user interface are
communicating. The NDVI shown is the combined
real-time value from all sensors on the left and
right booms respectively.
Note – The Version 1.2 Status screen does not show the NDVI table.
Errors tab
To make setup and troubleshooting easier, this tab shows
the ID and error codes from each sensor (version 1.3x of
the RT Commander software and later). Error codes are
short messages to help diagnose any problems related to
a sensor. The ID is the last two characters of the serial
number of the sensor.
NDVI values for crop analysis should range from 0.000 to
0.999. Therefore, the RT200 system uses negative NDVI
numbers to communicate error conditions to the RT
Commander software.
45
3
While the system does not enforce this, it is convenient to mount the sensors in
numerical order (by convention, with the lowest on the driver's left side) to aid in
diagnosis, or if doing high-resolution mapping with the RT220 system. If there is a
problem with a sensor or a connection, use this screen to isolate the location.
Error conditions
Error conditions include sensors disconnected from the CAN bus, or a sensor
transmitting invalid data. Invalid data could occur if the sensor malfunctions, or more
commonly, if it is seeing a target other than plants and soil. For example, when setting
up, the sensors may be pointed in the air, or against wet asphalt; either of these will
likely generate an error code from a sensor. The following errors are identified:
Error
Code
Description
-1
RED > NIR
Red reflectance higher than NIR
-2
BOTH < .01
Both reflectances below 0.01
-3
RED < .01
Red reflectance below 0.01
-4
NIR < .01
NIR reflectance below 0.01
-5
BOTH > .98
Either reflectance above 0.98
-.9
NIR < .015
NIR net reflectance below .015
-9.x
-9.x
All sensors responded with invalid data
-10.x
-10.x
No sensors responded at all
Comm View tab
Especially during setup, it is helpful to view this tab to
confirm if data is streaming to or from various sources,
which enables the operator to confirm cabling and serial
port settings. Do one of the following:
•
To see data from the RT200 system, select the
RT200 option.
•
To see GPS data, select the GPS option.
Data management
The default location for RT Commander files is My Documents. To save these files to
another location on the PDA, select a different location when setting up a new job. The
new location must be below My Documents.
The RT Commander software creates the following files that are typically used for
creating maps of the data using a shape file format:
[A/M][date][filename].dbf*
[A/M][date][filename].fgp
46
3
[A/M][date][filename].fsn
[A/M][date][filename].gpe
[A/M][date][filename].rtj
[A/M][date][filename].shp*
[A/M][date][filename].shx*
An example of an application job file is A20050120_North40.rtj
C
CAUTION – If the PDA has not been charged for several days, data will be lost. To avoid
this, do one of the following:
- Run the Backup Now utility installed on the PDA. This built-in backup is now done at the
factory to preserve the software installation. For information on using the backup utility,
see the Trimble Recon Getting Started Guide.
- Transfer the data from the PDA and save it to your computer.
- Copy the files to the CompactFlash card.
Application information
Delivery system and liquid control
As with any variable rate system, the minimum and maximum rates obtainable
depend on the delivery system. The RT200 system can request any rate, but the actual
rates delivered depend on the rate controller and its components. Most liquid rate
control systems control (“throttle”) the pressure of the system to affect flow and
application rate. There are also more advanced delivery systems that use two booms,
multiple nozzles, or special pulsing solenoids on each nozzle, to obtain larger rate
changes.
When using the RT200 system with a typical liquid delivery system, you must match
nozzle sizes to expected delivery rates. After the appropriate reference strip readings,
GDD, and selection of crop type are input into RT Commander software, the
application graph can be accessed to show the prescription rates at various sensor
NDVI readings. Review the Crop and Measurement screen features of the RT
Commander software to determine the expected delivery ranges in each specific field.
To do this, tap Show Table. Depending on the delivery system that is is used, there will
be actual minimum and maximum rates obtainable. These depend on components
such as the pump, control valve, nozzles, and boom plumbing sizes.
The RT Commander software has a feature that allows minimum and maximum rates
to be set, regardless of the crop algorithm prescription. Once you choose a nozzle set,
set the minimum at the lowest rate at which the nozzles will still give adequate
pattern/performance. Maximum rates may be limited by rates that lessen atomization
or drift.
47
3
Selecting a nozzle
It is usually best to match nozzles to the lower midrange of the typical rates shown on
the application graph. It is ultimately up to the grower or crop consultant to determine
the min/max rates and nozzles that are most appropriate.
Example
If most of your NDVI readings (in the area of the field not
in the NRS) are around 0.53, and the application graph
shows at 0.53 NDVI you should apply 15 GPA, select a
nozzle that can change rates above and below this NDVI
reading. You could select a nozzle that puts out 12.5 GPA
at its lowest pressure ( for example, 20 psi) and 21 GPA at
its highest pressure ( for example, 60 psi). Since the
penalty to under-fertilize (harm yield) is usually greater
than to over-fertilize (waste fertilizer), it may be best to
choose a strategy similar to the one shown here. Modify
the settings to fit your circumstances and to meet local
field and delivery system conditions.
Troubleshooting
•
If you do not hear the chimes after turning on the PDA (see Setup and
configuration, page 35) or do not get serial communication to GPS and/or the
RT200 system, perform a soft reset by holding the Power button down for
approximately eight seconds. Then turn off and turn on the PDA. If you still do
not hear the chimes, the PDA does not have a chimes feature—wait at least 10
seconds before opening any applications. Do not launch the RT Commander
software until you hear both chimes or until at least 10 seconds have passed.
•
Trimble recommends that you run a backup often to ensure you never lose any
data due to an unforeseen hard reset. For more information, refer to the Trimble
Recon Handheld Getting Started Guide.
•
If you do not see a black path being drawn on the map screen, verify that the
signal quality of GPS is set no higher than 1. Go to GPS Setup and then select the
Quality tab.
Note – Rate commands are not sent unless a valid GPS signal is received. If there is not an
adequate GPS signal, switch to GPS Setup / Simulation to set up the rate controller.
For more information, refer to the online troubleshooting document. Go to
www.greenseeker.com and then select Support / Technical Notes /RT200
Troubleshooting Tree.
48
APPENDIX
A
Cable Diagrams
A
This appendix includes the relevant cable assembly diagrams.
51
A
Cable Diagrams
Figure A.1
52
RT200 serial cable assembly
Cable Diagrams
Figure A.2
A
GreenSeeker RT200 interface module power cable
53
A
Cable Diagrams
Figure A.3
54
GreenSeeker interface module to sensor CAN bus cable
Cable Diagrams
Figure A.4
A
GreenSeeker interface module to PDA cable
55
A
Cable Diagrams
Figure A.5
56
Cable assembly, GreenSeeker to display
APPENDIX
B
Custom Algorithm
In this appendix:

Custom Formula
B
The Custom Formula feature enables you to
select the application rates that will be applied at
different sensor readings. In version 1.3.x of the
RT Commander, software, you can add
interpolation to the 16 point table. A 100 point
table has also been added.
All positions in the 100 point table must have a
valid rate entered.
57
B
Custom Algorithm
Custom Formula
1.
Select New Custom Formula from the drop-down
list.
2.
You must name the formula—enter a name in the
Custom Formula field.
3.
Select the rate at which the RT200 system will send
the applicator's rate controller as sensor values
change. The standard table is 16 rates, spanning
NDVIs of 0.20 - 0.95, with an interpolation option. A
high-resolution choice has been added with 100
points for NDVIs of 0.00 to 0.99.
Note – The horizontal scroll bar at the bottom of the gray
area allows you to access additional fields. You must enter a
value in each rate box.
4.
58
When finished, tap OK to return to the Crop &
Measurement Parameter screen.

GreenSeeker RT200 System Installation and Operation Guide

Transcription

Similar documents

Atlantis Energy Systems Inc.

Personal lnforrnation Date (moryo-

Coffing EC3 Manual

Terramodel Software for Construction

Session 1 (Pannuto) - USAID Learning Lab

Partners in Education

Medicapteurs WIN-POD GB 2007

Weekend Wrenchin - HGM Automotive Electronics

GW 031A - GULIWER Electronics

Regions CD Check Viewer Installation Guide