ndurable - Concrete Construction Supply

NDURABLE
CONCRETE PRODUCTS
TM
TESTIMONIALS
“I’m often asked by my clients for stained concrete that not only has depth, but also has many color selections. My first choice is
ENDURABLE. My go to sealer for exterior and interior concrete countertops is ENDURABLE SEALER. Easy to use and great chemical
resistance.”
MATT BOWEN -- PREP CONCRETE AND CONSTRUCTION -- CALIFORNIA
“I have been using your concrete products for about three years now and so far am impressed with its durability and the fact that
I’m not working around solvents is a huge plus for my crew and me.”
JASON OLINGER -- INNOVATIVE CONCRETE SOLUTIONS -- CALIFORNIA
“I am highly impressed with the ease of use with your concrete stain products. The ENDURABLE PRODUCTS are easy to use and
very flexible for the beginner.”
ESTEBAN PEREZ -- NOPAL CORP -- CALIFORNIA
“I recommend ENDURABLE brand products due to their superior quality, value, and long-lasting durability. I have used
ENDURABLE STAINS, DYES, STRIPPERS, SEALERS, AND POLYMER PAVEMENT on numerous jobs with great results.”
RANDY SHERER -- SHASTA PRESSURE CLEAN -- CALIFORNIA
“My company has been using ENDURABLE PRODUCTS and we wish we had found them 10 years ago. They are great and long-lasting,
therefore, eliminating customer complaints and callbacks. We have used acrylics and lacquers and the ENDURABLE line lasts a lot longer.”
LARRY FULLER -- FULLER STONE CARE -- CALIFORNIA
“We have been selling ENDURABLE STAIN and ENDURABLE SEALER for two years now. Before we started selling the products,
we sold a lot of acid stain and Dye-N-Seal. They are both good products but the have down sides that the ENDURABLE STAINS don’t have.
It is much easier to sell a product that has no clean up and disposal issues that acid stains have. ENDURABLE STAIN AND ENDURABLE
SEALER are both safe and easy for an inexperienced user. Also, the fact that we can use the stain both interior and exterior makes it so
much easier to sell. I was on an acid stain job last week that the contractor used a jade color outside. It has turned black and it’s a big mess.
We tell people not to do that but it still happens.
We sell the ENDURABLE STAIN at least 20 to 1 over acid stains and our Dye-N-Seal sales have mostly gone away. We have fewer
problems and sell far more product than we ever did when we only had acid stain and Dye-N-Seal to offer.
We have struggled with finding a sealer that would hold up outside since we got into decorative concrete 20 years ago. We have
tested different sealers on our own here and found that a good sealer, applied correctly, would last for maybe two years. So many of our
customers were discouraged with their stamped concrete because they couldn’t keep it looking nice. I have heard more than one person
say that they wished they had poured regular gray concrete. We have always stated that the key to a good stamp job is the sealer. Now
we have many of our regular customers using the ENDURABLE SEALER; exterior for its UV resistance and interior for its durability. It’s
an easy sell to homeowners when they come in; to tell them they can buy my solvent sealer and recoat it every other year, or buy the
ENDURABLE SEALER and have it last 3 to 5 times as long.
We have also found the company very easy to work with. They are very knowledgeable and always helpful with product
information. It is very discouraging to sell a product when you can’t get good technical support from the manufacturer. We love the
products and the company.”
KEN FERNANDEZ -- CONCRETE CONSTRUCTION SUPPLY - IDAHO
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
• Non-reactive and semi-transparent
• Will penetrate and color most porous surfaces
• May be mixed in water, acetone, or
denatured alcohol
• Low VOC content
• Low odor
• Small particle size to allow maximum penetration
• Excellent light fastness provides optimum
resistance to UV rays
• Concentrated to maximize shipping and shelf
space
• Application versatility provides infinite
appearance options
• Sealer may be applied immediately after stain is
dry to the touch (typically 30 minutes or less
when mixed in water and 5 minutes or less when
mixed in acetone)
• No binders, such as acrylic, which create a bond
breaker for sealers
NDURABLE
CONCRETE STAIN
TM
APPLICATION INSTRUCTIONS: ALWAYS PERFORM TEST AREAS. CONCRETE
MUST BE DRY. SHAKE OCCASIONALLY DURING APPLICATION TO KEEP COLOR
IN SOLUTION. Mix product into water, acetone, or denatured alcohol with a mixing
drill and paddle or by vigorous shaking. Apply product via pump sprayer with a
conical tip. Tip size of .05 to .15 gpm at 40 psi is recommended to reach proper
coverage rates. Determine if the concrete is porous with a simple water test. If
water drops in and darkens the concrete immediately, then opening the pores may
not be necessary. If the surface is a troweled surface, you should mechanically
grind or chemically etch the concrete to open the pores for optimum penetration of
the stain. If neither is an option, we highly recommend applying ENDURABLE
INCEPTIVE COATING prior to application of stain and sealer. If there is a sealer
present and in good condition, you may put a drop of acetone on the surface and
rub with your finger to determine if the stain will penetrate when mixed in
acetone (surface will feel sticky or tacky when you rub if it can be penetrated with
acetone.) Applying stain over existing sealer is not the recommended application
for optimum longevity. Water is not recommended when applying to overlay
systems that are commonly high in polymer. The water will often raise the polymers
to the surface. Using more than one color will often help to achieve a beautiful
mottled look. After the stain is applied there may be residue that can be removed
by buffing the floor. If you do not wish to buff the floor, you may wear booties to
keep from leaving footprints in the residue. After the stain is dry to the touch, seal
with ENDURABLE CONCRETE SEALER OR ENDURABLE F1 SEALER. The concrete
should be free from contamination. It is recommended to determine if the
concrete needs to be cleaned with a concrete cleaner or pressure washed. (If fungus
is present in the concrete, you should clean with a fungus killing product and then
pressure wash.) There may be residue left on the surface, most notably when the
carrying agent is acetone, and when applied to a surface that has low porosity. You
may wish to remove the excess residue with a white buff pad when working on a
flat surface, but it’s not necessary on broom-finished concrete. A light coat is
recommended as the stain will go far and over-application will result in excess
residue and it will lower your coverage rate.
SHELF LIFE: Undetermined - minimum of 8 years.
PACKAGING: Concentrate to make 1 gallon and a concentrate to make 5 gallons.
COVERAGE RATES: 400 to 600 square feet per gallon.
WARNING: Always be cautious with flammable carrying agents. Extinguish all
ignition points and use approved respirators when applicable.
WARRANTY: You must evaluate and determine whether this product is suitable for your
intended application. Since conditions of product use are outside of our control and vary
widely, the following is made in lieu of all express or implied warranties of merchantability.
Our only obligation and your only remedy is replacement of product, at the option of HDIP INC.
In no case will HDIP INC. be liable for any direct, indirect, special, incidental, or consequential
damages including lost profits, goodwill, or business opportunity.
Color samples for representation only - actual colors may vary
Amber
Canary
Citron
Dark Chocolate
Milk Chocolate
Moss
Mustang
Obsidian
Orange Crush
Orchid
Pacific
Padre
Rage
Sand
Storm Cloud
Topaz
Saddlehorn
Rust
Sonora
Pronghorn
White
“Having had the opportunity of using the ENDURABLE
PRODUCTS, we are very excited at the performance of
both the color stain and water-based sealant for
longevity and ease of use.”
G. LEE CUMMINGS
CUMMINGS MASONRY & LANDSCAPE INC.
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
• Does not leave discoloring salt deposits
• Compatible with ENDURABLE dyes and stains
• Works well with overlay products typically low in lime
• Lower PH than silicates
• Fast reaction times -- typically under 1 hour
• No overnight curing process
• Concentrated to lower shipping costs
• May be applied to new concrete 2-3 days after pour
• Silica particle size between 3 and 5 nanometers
• Colloidal silica is able to bond to silica present in concrete
• Product has the ability to bond to itself, unlike silicates
• Increases abrasion resistance
• Increases moisture resistance
• Enables polishing process
• Reduces dusting
• Reduces efflorescence
• Water-based
• Zero VOC content
• Non-toxic
• Safe to handle
• Does not require agitation
• Does not require hazardous disposal
• Improves performance of concrete
• Improves appearance of concrete
• Extends life of concrete
• Increases surface hardness
• Increases compressive strength
NDURABLE
CONCRETE HARDENER
TM
ENDURABLE CONCRETE HARDENER is nearly 100% pure silica at a size between 3 & 8 nanometers. The proprietary solution in which it is suspended, provides low surface tension,
resulting in excellent penetration of the silica into the concrete. The reaction of the silica with the remaining unreacted calcium hydroxide in the concrete, forms calcium silica hydrate.
When concrete is poured, calcium silica hydrate is formed as the concrete cures. This process only continues, as the concrete remains wet. After the concrete is dry, no additional calcium
silica hydrate is formed and the top surface of the concrete is usually left with unreacted calcium hydroxide, also known as lime. Obviously, the first part of the concrete to dry is the
surface, therefore leaving a substantial amount of unreacted calcium hydroxide. This unreacted calcium hydroxide is akin to an epoxy with only the first component used. The hardener
acts like the second component of the epoxy to actually create the chemical reaction, leaving the concrete harder and more abrasion-resistant. Colloidal Silica is distinctive in its ability to
bond to the silica already present in concrete and it can also bond to itself. This allows for a much greater density than can be found with any silicates. The families of silicates include
sodiums, potassiums, and lithiums. None of these products can match the abilities of colloidal silica to bond with the silica in the concrete, nor can they bond to themselves. Now that the
superiority of colloidal silica over the silicate families has been established, one last question remains. What is the difference between colloidal silicas? This question is an important one
when choosing your concrete hardener. The difference between colloidal silicas is how the silica is stabilized. The most effective way is lithium stabilization. Another method, and probably
the most common, is sodium stabilization. This method is less expensive, therefore most colloidal silica concrete hardeners are sodium stabilized. The reason lithium stabilization is
superior lies in the reaction of the silica when applied to concrete. Lithium stabilized colloidal silica produces more reaction points, yielding a harder concrete than the more common
sodium stabilized colloidal silica. When looking to choose the best hardener, one should look at the superior technology of colloidal silica over the other silicate families. Then one should
look at the best technology of stabilization, which is lithium stabilized colloidal silica. The size of particle should also be considered. The smaller the particle size, the better the results as
there are more reaction points and the product can travel further into the concrete at the smaller size. ENDURABLE CONCRETE HARDENER is a lithium stabilized colloidal silica with the
smallest particle size available at 3 to 8 nanometers, making it the best choice for a concrete hardener.
COVERAGE RATES: 300-700 square feet per gallon depending on porosity of concrete. High porosity concrete will be on the lower end and polished low porosity concrete will be on the
higher end.
PACKAGING: Concentrate that makes 4 gallons & concentrate that makes 20 gallons.
SHELF LIFE AND STORAGE: Store product in temperatures between 40 and 100 degrees Fahrenheit. Do not freeze. Product has a shelf life of 2 years from date of purchase when stored in
original unopened container.
WHERE TO USE: Use on any concrete surface or cementitious overlay product.
APPLICATION INSTRUCTIONS: This product is concentrated and should be mixed 3 parts water to 1 part product.
1. Shake product before mixing with water.
2. Stir the concentrate and water together for 30 seconds with a mixing drill and paddle. It may also be shaken for 1 minute.
3. Before application, be sure that concrete is clean and structurally sound. It must be free of any sealers, curing membranes, oils, dust, etc. Product must be able to achieve full contact
with concrete to be fully effective. Do not use acidic cleaners. Use a PH neutral cleaner.
4. Use a low-pressure pump sprayer. Be sure to shake product right before putting into sprayer. Use a conical tip that sprays .05 to .15 gallons per minute. Spray with the tip1 to 2 feet above
the surface and use a circular motion to achieve an even application. Spray enough product to achieve an even look of saturation. Keep the surface wet for a minimum of 15 minutes,
applying additional product when necessary to keep surface wet.
5. Allow surface to dry completely. This usually takes less than one hour. If concrete seemed porous on the first application, you may wish to apply a second application to achieve optimum
formation of calcium silica hydrate.
6. When using product in conjunction with polishing, it is best to apply the product at 200 or 400 grit. If desired, ENDURABLE CONCRETE DYE should be applied prior
to the application of hardener. A second application of ENDURABLE CONCRETE DYE may be used to achieve a richer color in the concrete after the ENDURABLE CONCRETE HARDENER
has been applied and is completely dry.
TEST DATA:
ABRASION RESISTANCE (ASTM C779)
COMPRESSIVE STRENGTH (ASTM C39)
IMPACT RESISTANCE (ASTM C805)
33% increase at 30 minutes
40% increase at full concrete cure
14% increase at full concrete cure
LIMITATIONS: Product should not be cleaned with citric or abrasive cleaners. PH neutral cleaners should be used for long-term maintenance. This product is not a “sealer” and will not
prevent staining. Use another ENDURABLE product if you wish to seal and protect from staining.
PRODUCT AVAILABILITY: Product is available through retail distributors around the world. Go to www.endurableproducts.com to find the nearest distributor.
DISPOSAL: Product is safe, biodegradable, and environmentally friendly.
WARNINGS: Use with proper ventilation. May cause eye and skin irritation. If you experience headaches, dizziness, or watery eyes, you may wear a NIOSH TC-84 respirator during
application. Use extreme caution when walking on wet product, as the product is slippery when wet.
WARRANTY: HDIP INC. warrants that properly prepared and structurally stable concrete treated with ENDURABLE CONCRETE HARDENER, according to the manufacturer’s instructions
will remain dustproof and hardened for a minimum of 20 years. This warranty does not apply if product is not applied properly or if structural faults occur due to faulty workmanship,
improper design, or failure of materials other than ENDURABLE CONCRETE HARDENER. Remedy of failure is sufficient ENDURABLE CONCRETE HARDENER, supplied at the
manufacturer’s expense, to reapply to defective area.
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
• Available in matte and gloss
• Easy to apply via sprayer, t-bar microfiber
applicator, or roller
• Low VOC content
• Low odor
• Heavy duty
• Perfect for forklift traffic, parking garages,
and other commercial applications
• Excellent UV stability - will not yellow or
degrade in sunlight
• Anti-graffiti - excellent resistance to solvents
• Safe for countertop use
• Excellent chemical resistance
• Excellent durability and scratch resistance
• Excellent resistance to hot tire pickup
• Excellent versatility allows for interior and
exterior use. Use on residential or commercial
applications
• Excellent coverage makes product very cost-effective
NDURABLE
CONCRETE SEALER
TM
ENDURABLE CONCRETE SEALER is a revolutionary sealer created from cutting edge polyurethane technology that allows for maximum penetration, durability, and chemical
resistance, while still delivering ease of application.
COVERAGE RATES: 300 – 800 square feet per gallon depending on porosity of surface.
PACKAGING: Concentrate that makes 1.12 gallons, 4.5 gallons, & 9 gallons (9 gallon concentrate may be made 4.5 gallons at a time.)
MIX RATIO: Water is mixed with the sealer components at a ratio of 2 parts water to 1 part mixed sealer components (for fastest dry times on smooth surface concrete, mix the second coat
of sealer at 1 part water to 1 part mixed components.)
SHELF LIFE AND STORAGE: Product has a shelf life of a minimum of 1 year in original containers. Store product between 40 and 77 degrees Fahrenheit. Keep product free from excessive
heat, moisture, and freezing.
WHERE TO USE: Concrete – garages, driveways, patios, walkways, countertops, pool decks, commercial floors, etc., masonry, terrazzo, and natural stones.
MAINTENANCE: Use mild detergent solutions, light vinegar solutions, or light ammonia solutions. Reseal as necessary – 5 to 10 years depending on traffic and usage. Routine buffing with
a light pad on a low-speed buffer can help maintain an even sheen and a clean surface.
DURABILITY AND CHEMICAL TESTING AND PERFORMANCE RESULTS:
Abrasion Resistance
H-18 1000 cycles, mg loss
ASTM D 2060
260
Abrasion Resistance CS-17 1000 cycles, mg loss
ASTM D 2060
25
Modulus of Elasticity, kpsi
ASTM D 638
175-300
APPLICATION INSTRUCTIONS:
Tensile Strength, psi
ASTM D 638
4400-7200
For optimum results, open troweled concrete mechanically. Apply to dry, porous concrete. Mix
Tear Strength, pli
ASTM D 624
150-300
Component 1 with Component 2, then mix with twice as much water as components. Use a mixing
Artificial Weathering
ASTM C 23
None
drill and paddle for minimum of 2 minutes. Pot life is 45 to 90 minutes on matte and 90 to 180
VOC Content
ASTM D3960
< 1%
minutes on gloss. Do not apply 2nd coat until 1st coat is completely dry. Product may be applied via
Pendulum Hardness Test ASTM D4366 1 Day – Matte- 38 seconds/Gloss-38 seconds pump sprayer with a conical tip - .05 to .15 gpm at 40 psi, airless sprayer, or T-Bar micro-fiber
Pendulum Hardness Test ASTM D4366 5 Day –Matte- 154 seconds/Gloss-174 seconds applicator. When applying over stain, it is recommended to spray the first coat to avoid movement of
Pendulum Hardness Test ASTM D4366 7 Day –Matte-162 seconds/Gloss-184 seconds color residue. Second coat MUST be applied via microfiber T-Bar applicator or low-speed buffer when
Coefficient of Friction Test ASTM D-2047 Dry -- 0.6
Wet -- 0.47
dealing with smooth surface floors. Second coat may be applied via sprayer on most exterior concrete.
Water Vapor Transmission ASTM E 96
1.26 grains/hour/square foot
DO NOT OVER-APPLY. Coverage rates are typically between 300 and 500 square feet per gallon per
CHEMICAL RESISTANCE TESTING ACCORDING TO ASTM D 1308
coat on the first coat depending on porosity of surface. Subsequent coats or low porosity surfaces may
Product cured for 14 days at 70 degrees Fahrenheit before testing
yield higher coverage rates of 500-800 square feet per gallon. Before application of sealer, make sure
CHEMICAL
Time-- 4 hours
Time--24 hours
surface is free from dirt, oils, previous sealers, etc. It must be applied in thin coats. Two coats are
Betadine
No Effect
No Effect
usually sufficient, but applicator must determine the specific need. Sealer should be applied between
Bleach
No Effect
No Effect
40 and 90 degrees Fahrenheit. After applying the first coat, wait until the sealer is dry to the touch,
Gasoline
No Effect
No Effect
usually 45 to 180 minutes for matte, 3-6 hours for gloss, depending on temperature and air flow, and
Acetic Acid
No Effect
No Effect
then subsequent coats may be applied. Subsequent coats typically take 3 to 8 hours to dry for matte
Water
No Effect
No Effect
and 6 to 24 hours for gloss depending on temperature and air flow. After application, tools may be
MEK (complete immersion)
Slightly Soft
Soft
cleaned using soap and water. Light traffic is possible after 8-24 hours and heavy traffic is possible
Brake Fluid
No Effect
Slightly Soft
after 24-48 hours. The sealer will gain strength over the next few days after application and will reach
H2SO4
No Effect
No Effect
full cure at 7-10 days. Avoid subjecting the sealer to freezing temperatures or moisture for 12-36
IPA
No Effect
Slightly Soft
hours after application. Make sure substrate is dry before application. Endurable Concrete Stain can
HCI
No Effect
No Effect
penetrate product for the first 4 hours after sealer is dry when stain is mixed in water. Endurable
Skydrol
No Effect
No Effect
Concrete Stain may penetrate product when mixed in acetone for the first two days after application.
NaOH
No Effect
No Effect
If applying stain mixed in acetone over sealer, spray VERY lightly. Too much acetone can “cook” the
NH4OH
No Effect
No Effect
sealer. Upon further curing, the stain cannot penetrate unless an additional coat of product is applied.
Only ENDURABLE VERTICAL STRIPPER may remove products when sealer is fully cured. This
LIMITATIONS: Product should be applied in thin coats. Do not over-apply. Product
requires the stripper to be covered and remain wet for a minimum of 12 to 24 hours. FOR TIPS AND
must be applied to clean, dry substrates. It is recommended to apply to porous
TECHNIQUES, VISIT OUR WEBSITE AT WWW.ENDURABLEPRODUCTS.COM UNDER THE
surfaces for longest-lasting results. Product should not be applied to concrete with
ENDURABLE CONCRETE SEALER DROP-DOWN MENU. It may be beneficial to strain product before
moisture related issues. If moisture issue is suspected, email
use.
[email protected] to get a recommendation on how to deal with the
PRODUCT AVAILABILITY: Product is available at retail distributors around the world. Visit
moisture issues prior to application of sealer.
www.endurableproducts.com to find the nearest distributor.
WARNINGS: Use with proper ventilation. May cause eye and skin irritation. If you
SLIP RESISTANCE AND CLEANABILITY: The profile of the concrete will dramatically affect the
experience headaches, dizziness, or watery eyes, you may wear a NIOSH TC-84
slip-resistance. Aggressive finishes, such as broom-finished concrete, will yield the best
respirator during application.
coefficient of friction and will be slightly more challenging to clean. Smooth surfaces will yield a
WARRANTY: Evaluate whether this product is suitable for your intended application. Conditions
of product
use are
outside
of our
lower coefficient
of friction
but
are easier
to clean. If desired, additional slip resistance can be added
control and vary widely, the following is made in lieu of all express or implied
to the sealer. 100 mesh polypropylene will work well and should be applied in the second coat. It is
warranties of merchantability. Our only obligation and your only remedy is
best to mix it into the sealer and then apply with a T-Bar or the additive can be broadcast into the
replacement of product, at the option of HDIP INC. In no case will HDIP INC be
sealer. When slip-resistant additive is used, it is recommended to mix the sealer 1 to 1 with water to
liable for any direct, indirect, special, incidental, or consequential damages
help keep the additive in solution. It is also recommended to apply a third coat of sealer to
including lost profits, goodwill, or business opportunity.
completely encompass and protect the additive.
“It’s sealer that really works!”
MARK CHEW - SPECIALTY DIVISION MANAGER
LOGAN CONTRACTORS SUPPLY
“It’s the best sealer I’ve ever seen and I have over
30 years of experience in the industry.”
STEVE CREASY - JUST CONCRETE FLOORS
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
• Excellent durability - suitable for commercial use
including forklift traffic
• Lower cost than alternative products such as
concrete, asphalt, and cement-based overlay systems
• Incredibly easy to apply. Less costly and less time
intensive than alternative epoxy coating systems
• May be applied directly over troweled concrete
without grinding
• Numerous fill material options, including sand
• Product can receive stain and sealer immediately
after product is dry to the touch - typically 4 to 6
hours
• Infinite appearance options when used in
conjunction with ENDURABLE stains and sealers
• Excellent longevity
• Low VOC content
• Fast drying
• Good early water resistance
• Bonds well to almost any stable surface
• Excellent crack fill material - very cost-effective
NDURABLE
POLYMER PAVEMENT
TM
COVERAGE RATES: 50 to 200 square feet per gallon depending on porosity and texture of surface.
PACKAGING: Concentrate that makes 3 gallons.
MIX RATIO:
Water is mixed with the sealer components at the following ratio:
1 Part Component 1
1 Part Component 2
1 Part Water
POT LIFE: Pot life is 2 – 4 hours.
DRY TIME: Approximately 4 hours for initial dry-to-the-touch. Approximately 6 -12 hours for light traffic. Approximately 24 to 48 hours for heavy traffic.
Product will gain strength over the next several days and will reach full cure at 7 days. It is recommended to wait as many days as possible before driving over
the product with vehicles or heavy equipment.
SHELF LIFE AND STORAGE: Product has a shelf life of a minimum of 2 years in original containers. Store product between 40 and 90 degrees Fahrenheit.
Keep product free from excessive heat, moisture, and freezing.
MAINTENANCE: Use mild detergent solutions, light vinegar solutions, or light ammonia solutions. It is recommended to seal with ENDURABLE CONCRETE
SEALER every 5 to 10 years.
TESTING AND PERFORMANCE RESULTS: (product was applied to test slab after 24 hour cure)
BOND STRENGTH (measured in psi):
7 Day Cure
-- Steel Trowel
419
-- Broom Finished
300
30 Day Cure
-- Steel Trowel
531
-- Broom Finished
385
WATER VAPOR TRANSMISSION: ASTM E96-95 WET CUP
Water vapor transmission
-9.75 x 10-4
Water vapor permeability
-6.67 x 10-7
Persoz Hardness -@ 24 Hours
200
-- @ 7 Days
350
APPLICATION INSTRUCTIONS: Apply product to stable surface. Test areas are always recommended to confirm suitability of substrate and to achieve comfort
level with application procedure. Product is a two-component system. Mix one part Component 1, one part Component 2, and one part water. Mix in a
5 gallon bucket with a mixing drill and paddle for a minimum of two minutes. Apply product with a magic trowel, hand trowel, roller, or other suitable
instrument to achieve an even application that leaves between 1 to 4 mils of product on surface. After troweling a small area, allowing installer to reach the
entire area with broadcast material. Suitable fill material includes base sand, quartz, or other suitable fill material. Broadcast fill until rejection. After applying
1 coat over the entire area, it is recommended to wait for product to dry until surface is hard enough to sustain light traffic. This is typically 4 to 6 hours. Then
you may choose to repeat the process to achieve a second layer of ENDURABLE POLYMER PAVEMENT. After the product is dry enough to sustain light traffic,
it may be stained with ENDURABLE CONCRETE STAIN. The final step is to apply two coats of ENDURABLE CONCRETE SEALER.
LIMITATIONS: Product must be applied properly to achieve optimal results. Product should not be applied over unstable surfaces. Product may yellow over
many years on exterior applications. Therefore, it is recommended to use ENDURABLE CONCRETE STAIN and ENDURABLE CONCRETE SEALER to avoid visible
yellowing on exterior jobs.
PRODUCT AVAILABILITY: Product is available at retail distributors around the world. Visit www.endurableproducts.com to find the nearest distributor.
SLIP RESISTANCE AND CLEANABILITY: Due to the fill material, the finished product has excellent slip resistance. Cleaning should be done with a light vinegar
solution or a light ammonia solution.
WARNINGS: Use with proper ventilation. May cause eye and skin irritation. If you experience headaches, dizziness, or watery eyes, you may wear a NIOSH
TC-84 respirator during application.
WARRANTY: Evaluate whether this product is suitable for your intended application. Conditions of product use are outside of our control and vary widely. The
following is made in lieu of all express or implied warranties of merchantability. Our only obligation and your only remedy is replacement of product, at the
option of HDIP INC. In no case will HDIP INC be liable for any direct, indirect, special, incidental, or consequential damages including lost profits, goodwill, or
business opportunity.
“POLYMER PAVEMENT is a cost-effective alternative to epoxy
and polyspartic coatings for interior and exterior applications.
It is easy to apply the base coat, broadcast the media (sand,
colored quartz, vinyl chips, etc.), add stain if desired, and
top coat the media with ENDURABLE SEALER.”
RANDY SHERER -- SHASTA PRESSURE CLEAN
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
• Product contains no toxic solvents
• Product contains no caustics
• Works on almost any sealer, coating,
varnish, or paint
• Long-lasting as evaporation rate
is much slower than typical
solvent-based strippers, allowing
product to remove several layers of
coatings without losing strength
• Easy to apply by roller or mop
• It will not burn skin
• Mild odor allows for indoor applications
• Clean-up is easy
• Works over most substrates (not
recommended over resilient surfaces
such as vinyl, vct, or rubber)
• Good coverage rates make product
very cost-effective
NDURABLE
POWER STRIPPER
TM
COVERAGE RATES: 75-200 square feet per gallon depending coating to be removed and how many layers of coating.
PACKAGING: Available in 1 gallon jug and 5 gallon bucket.
SHELF LIFE AND STORAGE: Product has an unlimited shelf life when left unopened in original containers. Keep product free from
excessive heat. Product should be applied at temperatures above 45 degrees or product may not be fully effective.
WHERE TO USE: Use on any horizontal substrate other than resilient surfaces, such as vinyl, vct, or rubber.
APPLICATION INSTRUCTIONS: We highly recommend doing a small test area to determine effectiveness, coverage rate, and time needed
for product to work.
1.
Properly mask off areas with polyethylene sheeting and tape before applying product.
2.
Completely wet the surface with ENDURABLE POWER STRIPPER. The best way to apply the stripper is with a mop or a roller.
You may use a brush, or other type of applicator, but mop or roller is the easiest for large areas.
3.
Allow time for stripper to work. The coating needs to be completely softened before removal, so allowing the stripper to complete
its job is very important. This can take several hours. Covering the material with polyethylene sheeting is an option for keeping the
material wet and working, especially in hot conditions. As long as the material is shiny and wet, it is still absorbing and working on
the coating. If the material is not shiny, it may require more stripper. DO NOT LET PRODUCT DRY OR YOU MAY HAVE TO REPEAT
THE PROCESS. THE COATING MAY RECONSTITUTE IF IT DRIES.
4.
Test the coating to determine if the product is ready for removal. Scratch a small area. If the coating comes up easily, it is ready for
removal. If not, let the product continue to work. In some cases the stripper will make the coating gooey and if this occurs,
continue to apply more material and agitate the coating until the product liquefies.
5.
Removal of the coating can be performed with scrapers, high-pressure water, or a low-speed buffer with strip pads or brushes. After
the coating is completely removed, clean the surface with soap and water. The slurry can be removed with a wet-vac.
LIMITATIONS: Product should be applied at temperatures above 45 degrees Fahrenheit. You should not walk on the stripper with rubber or
vinyl soled shoes as the stripper softens rubber and vinyl.
PRODUCT AVAILABILITY: Product is available at retail distributors around the world. Go to www.endurableproducts.com to find the
nearest distributor.
DISPOSAL: Product is safe, biodegradable, and environmentally friendly. However, if the coating that is being removed is hazardous,
check with local, state, and federal regulations for proper disposal.
WARNINGS: Use with proper ventilation. May cause eye and skin irritation. If you experience headaches, dizziness, or watery eyes, you may
wear a NIOSH TC-84 respirator during application.
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
AFTER
“I removed the paint with POWER STRIPPER and brought
the patio back to its original glory. This job would not
have been possible without ENDURABLE POWER
STRIPPER. Thank you!”
ROGER MCCLURE
PACIFIC STONESCAPES
BEFORE
WARRANTY: Evaluate whether this product is suitable for your intended application. Conditions of product use are outside of our control
and vary widely. The following is made in lieu of all express or implied warranties of merchantability. Our only obligation and your only
remedy is replacement of product, at the option of HDIP INC. In no case will HDIP INC be liable for any direct, indirect, special, incidental,
or consequential damages including lost profits, goodwill, or business opportunity.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
• Product may be mixed in water,
acetone, or denatured alcohol
• Product may be used
immediately after mixing into
carrying agent. Does not
require wait time (unlike
powdered dyes)
• High coverage rates of 400-600
square feet per gallon
• Product goes completely into
solution allowing deepest
penetration, making this
product the perfect solution
for polishing
• Concentrated to optimize
shipping costs and shelf space
• Vibrant color options offer
various looks
NDURABLE
CONCRETE DYE
TM
DYE IS FOR INTERIOR USE ONLY, DUE TO LOW UV RESISTANCE
Color samples for representation only - actual colors may vary
PACKAGING: Product is packaged as a liquid concentrate. Available in
concentrate to make 1 gallon and concentrate to make 5 gallons.
SHELF LIFE: A minimum of one year.
COVERAGE RATES: 400-600 square feet per gallon
APPLICATION INSTRUCTIONS: ALWAYS PERFORM TEST AREAS. CONCRETE
MUST BE DRY. The concrete should be free from contamination. Determine if the
concrete is porous with a simple water test. If the water drops in and darkens the
concrete immediately, then prep may not be necessary. If the surface is a troweled
surface, you may need to mechanically grind the floor to open the pores for better
penetration of the dye. Mix the dye into your choice of the water, acetone, or
denatured alcohol. Apply via pump sprayer with a conical tip or hvlp cup gun. Seal
with ENDURABLE CONCRETE SEALER or ENDURABLE F1 SEALER. Using more
than one color can help to achieve a beautiful mottled look. Use a pump sprayer
with a conical tip. Tip size of .05 to .15 gpm at 40 psi is recommended.
FOR POLISHED CONCRETE: Grind and polish the concrete to 200 or 400 grit.
Apply ENDURABLE CONCRETE DYE. Let dry. Apply ENDURABLE CONCRETE
HARDENER and then let it dry completely. At this point you may apply more dye
if desired or as needed. You may polish up to 800 or desired level of polish. Make
sure no dye residue is present on the surface. If you notice residue, buff the floor or
auto scrub the floor before applying sealer. Apply ENDURABLE CONCRETE
SEALER with low speed buffer via pump sprayer by lightly misting sealer, buff in,
and repeat until floor is sealed. Use a soft white pad on the buffer. Wait 4 to 8 hours
for sealer to harden to burnishable state. You may wait up to 24 hours if job
conditions and time constraints require a longer wait. The next step is to use
diamond impregnated burnish pads on a burnisher. Start with 200 grit pad, then
move to a 400, 800, and finally a 1500 grit pad. Beware of leaving the buffer on
an area for too long as it may damage the sealer. If the sealer is damaged by leaving
the buffer on an area too long, then one option for fixing the damaged area is to
buff a little more sealer on the area.
WARNINGS: Always be cautious with flammable carrying agents. Extinguish all
ignition points and use approved respirators when applicable.
WARRANTY: You must evaluate and determine whether this product is suitable for
your intended application. Since conditions of product use are outside of our
control and vary widely, the following is made in lieu of all express or implied
warranties of merchantability. Our only obligation and your only remedy is
replacement of product, at the option of HDIP INC. In no case will HDIP INC. be
liable for any direct, indirect, special, incidental, or consequential damages
including lost profits, goodwill, or business opportunity.
Amber
Camel
Canary
Caribbean
Dark Chocolate
Midnight
Concord
Citron
Evergreen
Deep Sea
Milk Chocolate
Rage
“I use ENDURABLE DYE for many of my
polished concrete floors. The ease of use
and highly vibrant colors, make these dyes
stand out above the rest.”
MATT BOWEN
PREP CONCRETE AND CONSTRUCTION
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
• Matte or gloss finish
• Quick to dry
• Spray, roll, or micro-fiber application
• Safe for countertops
• Low VOC content and low odor
• Good chemical resistance
• Good durability
• Very easy to apply
• Good UV stability
• Good against hot tire pick-up
• Excellent product to use in
conjunction with ENDURABLE
CONCRETE SEALER. Application
of product during recoat window
over ENDURABLE CONCRETE
SEALER results in rich look
usually achieved with floor wax,
yet yielding much longer term results
NDURABLE
F1 SEALER
TM
ENDURABLE F1 SEALER is great replacement for solvent-based sealers. Product has a low VOC content and is very easy to apply. The innovative chemistry used
to create this sealer provides a product that lasts twice as long as most acrylics.
COVERAGE RATES: 300 – 800 square feet per gallon depending on porosity of surface.
PACKAGING: Concentrate that makes 1 gallon & concentrate that makes 2 gallons.
MIX RATIO: Mix sealer at a ratio of 1 part water to 1 part sealer. Product may used without adding water. Eliminating water will speed dry time.
SHELF LIFE AND STORAGE: Product has a shelf life of a minimum of 1 year in original containers. Store product between 40 and 80 degrees Fahrenheit. Keep
product free from excessive heat, moisture, and freezing.
WHERE TO USE: Concrete – garages, driveways, patios, walkways, countertops, etc., masonry, terrazzo, and natural stone. Product has good resistance to
chlorine, making it an effective sealer on pool decks. This sealer is not recommended in applications where motor oils, hydraulic fluids, etc. may be applicable.
MAINTENANCE: Use mild detergent solutions, light vinegar solutions, or light ammonia solutions. Reseal as necessary – 2 to 5 years depending on traffic and
usage. Routine buffing with a light pad on a low-speed buffer can help maintain an even sheen and a clean surface.
DURABILITY AND CHEMICAL TESTING AND PERFORMANCE RESULTS
Adhesion
ASTM D3359
Dry Tape
5A
Adhesion
Wet Tape (24 hr @ 70 degrees F)
5A
Adhesion
Wet Tape (100 hr @ 70 degrees F)
5B
Adhesion
ASTM D2197A
Dry Scrape
8
Immersion
ASTM D870
Water (24 hr @ 70 degrees F)
No Effect
Double Rubs
ASTM D4752
IPA
>100
Double Rubs
ASTM D4752
MEK
>100
Impact Resistance
ASTM D2794
Reverse, in-lb
>160
Gloss, 60 degrees
ASTM D523
>95
Hardness
ASTM D4366
Persoz, s
>150
Mandrel Bend
ASTM D1737
mm
3.2
APPLICATION INSTRUCTIONS: Mix 1 to 1 with water. Use a mixing drill and paddle. Product may be applied via pump sprayer with a conical tip that sprays at
.05 to .15 gpm at 40 psi, airless sprayer, micro-fiber applicator, or roller. When applying over stain, it is recommended to spray the first coat to avoid movement
of color residue. Coverage rates are typically between 300 and 500 square feet per gallon per coat on broom finished or textured concrete.
Smooth surfaces or subsequent coats will yield coverage rates of 500-800 square feet per gallon. DO NOT OVER-APPLY. This product should be applied thinly
and evenly. Subsequent coats or low porosity surfaces will yield high coverage rates. Before application of sealer, make sure surface is free from dirt, oils, etc.
Two coats are usually sufficient, but applicator must determine the specific need. Three coats on textured concrete may help with maximum water resistance.
Sealer should be applied between 40 and 90 degrees Fahrenheit. After applying the first coat, wait until the sealer is dry to the touch, usually 15 to 30 minutes,
depending on temperature and air flow, and then subsequent coats may be applied. Subsequent coats typically take 20 to 40 minutes to dry, depending on
temperature and air flow. After application, tools may be cleaned using soap and water. Light traffic is possible after 2 hours and heavy traffic is possible after
8 hours. The sealer will gain strength over the next few days after application and will reach full cure at 5-7 days. Avoid subjecting the sealer to freezing
temperatures or moisture for 12-36 hours after application. Make sure substrate is dry before application. ENDURABLE CONCRETE STAIN may penetrate
ENDURABLE F1 SEALER when mixed in acetone. When applying stain in acetone over sealer, apply lightly. Too much acetone will “cook” the sealer.
LIMITATIONS: Product should be applied in thin coats. Do not over-apply. Product must be applied to clean, dry substrates. It is recommended to apply to
porous surfaces for longest-lasting results.
PRODUCT AVAILABILITY: Product is available at retail distributors around the world. Visit www.endurableproducts.com to find the nearest distributor.
SLIP RESISTANCE AND CLEANABILITY: The profile of the concrete will dramatically affect the slip-resistance. Aggressive finishes, such as broom-finished
concrete, will yield the best coefficient of friction and will be slightly more challenging to clean. Smooth surfaces will yield a lower coefficient of friction but
are easier to clean. If desired, additional slip resistance can be added to the sealer. 100 mesh polypropylene will work well and should be applied in the second
coat. It is best to mix it into the sealer and then applied with a T-Bar or the additive can be broadcast into the sealer. It is also recommended to apply a third coat
of sealer to completely encompass and protect the additive.
WARNINGS: Use with proper ventilation. May cause eye and skin irritation. If you experience headaches, dizziness, or watery eyes, you may wear a NIOSH TC-84
respirator during application.
WARRANTY: Evaluate whether this product is suitable for your intended application. Conditions of product use are outside of our control and vary widely, the
following is made in lieu of all express or implied warranties of merchantability. Our only obligation and your only remedy is replacement of product, at the
option of HDIP INC. In no case will HDIP INC be liable for any direct, indirect, special, incidental, or consequential damages including lost profits, goodwill, or
business opportunity.
“The F1, for its pricepoint, is one of the
best sealers I have used. It is easy to apply
and it goes a long way. I am happy to no
longer have to use solvent sealers that
smell terrible and turn white months later.”
MARK SHERER - SPARKLEWASH OF
PLACER COUNTY
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
NDURABLE
INCEPTIVE COATING
TM
BEFORE
AFTER
• Excellent high quality product to use on freshly
poured concrete - within 24 to 48 hours. Better
performance than typical cure & seal products
• Breathability 100 times greater than typical coatings
• Excellent bond strength makes product an ideal
primer - perfect to use when mechanical grinding
is not an option on troweled floors before
application of sealers or coatings
• Easy to apply
• Product can receive stain and sealer immediately
after product is dry to the touch - typically 4 to 6
hours
• Various appearance options when used in
conjunction with ENDURABLE stains and sealers
• Excellent longevity
• Low VOC content
• Fast drying
• Good early water resistance
• Bonds well to almost any stable surface
FINISHING THE ENDURABLE INCEPTIVE COATING WITH ENDURABLE CONCRETE STAIN AND ENDURABLE CONCRETE SEALER IS HIGHLY RECOMMENDED
COVERAGE RATES: 300 to 800 square feet per gallon depending on porosity of surface.
PACKAGING: Concentrate that makes 4 gallons.
MIX RATIO: Water is mixed with the sealer components at the following ratio:
1 Part Component 1
1 Part Component 2
2 Parts Water
If coating is used as a buildable coating instead of a primer coat, it is recommended to mix at the following ratio:
1 part Component 1
1 part Component 2
1 part Water
POT LIFE: Pot life is 2 – 4 hours.
DRY TIME: Approximately 4 hours for initial dry-to-the-touch. Approximately 6 -12 hours for light traffic. Approximately 24 to 48 hours for heavy traffic. Product
will gain strength over the next several days and will reach full cure at 7 days. It is recommended to wait as many days as possible before driving over the product
with vehicles or heavy equipment.
SHELF LIFE AND STORAGE: Product has a shelf life of a minimum of 2 years in original containers. Store product between 40 and 90 degrees Fahrenheit. Keep
product free from excessive heat, moisture, and freezing.
MAINTENANCE: Use mild detergent solutions, light vinegar solutions, or light ammonia solutions. It is recommended to seal with ENDURABLE CONCRETE
SEALER every 5 to 10 years.
TESTING AND PERFORMANCE RESULTS:
BOND STRENGTH (measured in psi): (Note the product during this test was applied after 24 hour cure on concrete test slab)
7 Day Cure
-- Steel Trowel
419
-- Broom Finished
300
30 Day Cure
-- Steel Trowel
531
-- Broom Finished
385
WATER VAPOR TRANSMISSION: ASTM E96-95 WET CUP
Water vapor transmission -- 9.75 x 10-4
Water vapor permeability -- 6.67 x 10-7
Persoz Hardness -@ 24 Hours
200
@ 7 Days
350
APPLICATION INSTRUCTIONS: Apply product to stable surface. Test areas are always recommended to confirm suitability of substrate and to achieve comfort
level with application procedure. Product is a two-component system. Mix one part Component 1, one part Component 2, and two parts water. Mix in a five-gallon
bucket with a mixing drill and paddle for a minimum of two minutes. Apply product with T-Bar micro-fiber or roller. After applying, it typically takes between
4 to 8 hours to dry. Depending on the use, a second application may be applied. If the application is as a primer, it is unlikely a second application is necessary.
If it is used as a buildable coating, it is recommended to apply the final coat at one part Component 1, one part Component 2, and one part water.
LIMITATIONS: Product must be applied properly to achieve optimal results. Product should not be applied over unstable surfaces. Product may yellow out over
many years when applied in exterior applications. Therefore, it is recommended to use ENDURABLE CONCRETE STAIN and ENDURABLE CONCRETE SEALER
over the product to avoid visible yellowing on exterior projects.
PRODUCT AVAILABILITY: Product is available at retail distributors around the world. Visit www.endurableproducts.com to find the nearest distributor.
SLIP RESISTANCE AND CLEANABILITY: Slip resistant additive may be added. If slip resistant additive is used, it is recommended to use it when the product is
mixed one part Component 1, one part Component 2, and one part water. Clean with a light vinegar solutions or a light ammonia solution.
WARNINGS: Use with proper ventilation. May cause eye and skin irritation. If you experience headaches, dizziness, or watery eyes, you may wear a
NIOSH TC-84 respirator during application.
WARRANTY: Evaluate whether this product is suitable for your intended application. Conditions of product use are outside of our control and vary widely, the
following is made in lieu of all express or implied warranties of merchantability. Our only obligation and your only remedy is replacement of product, at the
option of HDIP INC. In no case will HDIP INC be liable for any direct, indirect, special, incidental, or consequential damages including lost profits, goodwill, or
business opportunity.
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120
• Product contains no toxic solvents
• Product contains no caustics
• Works on almost any sealer, coating,
varnish, or paint
• Long-lasting as evaporation rate
is much slower than typical
solvent-based strippers, allowing
product to remove several layers of
coatings without losing strength
• Easy to apply by roller or mop
• It will not burn skin
• Mild odor allows for indoor applications
• Clean-up is easy
• Works over most substrates (not
recommended over resilient surfaces such as
vinyl, vct, or rubber)
• Good coverage rates make product very
cost-effective
• Gel form allows adherence to vertical surfaces
NDURABLE
VERTICAL STRIPPER
TM
COVERAGE RATES: 75-200 square feet per gallon depending coating to be removed and how many layers of coating.
PACKAGING: Available in 1 gallon jug and 5 gallon bucket.
SHELF LIFE AND STORAGE: Product has an unlimited shelf life when left unopened in original containers. Keep product free from
excessive heat. Product should be applied at temperatures above 45 degrees or product may not be fully effective.
WHERE TO USE: Use on any horizontal substrate other than resilient surfaces, such as vinyl, vct, or rubber.
APPLICATION INSTRUCTIONS: We highly recommend doing a small test area to determine effectiveness, coverage rate, and time needed
for product to work.
1.
2.
3.
4.
5.
Make sure to stir the product before use to a uniform consistency. Properly mask off areas with polyethylene sheeting and tape
before applying product.
Completely wet the surface with ENDURABLE VERTICAL STRIPPER. The best way to apply the stripper is with a paintbrush or
wallpaper paste brush.
Allow time for stripper to work. The coating needs to be completely softened before removal, so allowing the stripper to complete
its job is very important. This can take several hours. Covering the material with polyethylene sheeting is an option for keeping
the material wet and working, especially in hot conditions. As long as the material is shiny and wet, it is still absorbing and
working on the coating. If the material is not shiny, it may require more stripper. DO NOT ALLOW PRODUCT TO DRY OR YOU MAY
NEED TO REPEAT PROCESS. IF PRODUCT DRIES, THE COATING MAY RECONSTITUTE.
Test the coating to determine if the product is ready for removal. Scratch a small area. If the coating comes up easily, it is ready
for removal. If not, let the product continue to work. Repeat the process if necessary.
Removal of the coating can be performed with scrapers or high-pressure water. After the coating is completely removed, clean the
surface with soap and water or light sanding.
LIMITATIONS: Product should be applied at temperatures above 45 degrees Fahrenheit. You should not walk on the stripper with rubber or
vinyl soled shoes as the stripper softens rubber and vinyl.
PRODUCT AVAILABILITY: Product is available at retail distributors around the world. Go to www.endurableproducts.com to find the
nearest distributor.
DISPOSAL: Product is safe, biodegradable, and environmentally friendly. However, if the coating that is being removed is hazardous,
check with local, state, and federal regulations for proper disposal.
ROGER MCCLURE
PACIFIC STONESCAPES
All products are labeled with
full instructions. Additional
information may be found on
technical data sheets available
at our website:
www.endurableproducts.com.
You may also view helpful
instructional videos available
on the website.
AFTER
“I absolutely love your product.”
BEFORE
WARNINGS: Use with proper ventilation. May cause eye and skin irritation. If you experience headaches, dizziness, or watery eyes, you may
wear a NIOSH TC-84 respirator during application.
WARRANTY: Evaluate whether this product is suitable for your intended application. Conditions of product use are outside of our control
and vary widely. The following is made in lieu of all express or implied warranties of merchantability. Our only obligation and your only
remedy is replacement of product, at the option of HDIP INC. In no case will HDIP INC be liable for any direct, indirect, special, incidental,
or consequential damages including lost profits, goodwill, or business opportunity.
NDURABLE
CONCRETE PRODUCTS
TM
The website provides additional
tips and techniques for the
individual products. Color
selections are also available on
website.
www.endurableproducts.com
800-910-3120