001 DEADLATCH 2 1 3

PERFORATION
TEAR OFF
001 DEADLATCH
TIMBER JAMB
FOR INWARD OPENING DOORS WITH TIMBER JAMB
DOOR FRAME
STRENGTHENER
FOLLOW INSTRUCTIONS CAREFULLY
CYLINDER
DOOR FRAME
STRENGTHENER
SCREWS(2)
LOCK OPERATION
LATCH STRIKE
KEY OUTSIDE: Retracts latch bolt at all times.
KEY INSIDE:
Locks and unlocks turn knob by turning key
one full turn.
TURN KNOB:
Retracts latch bolt when unlocked.
DEADLATCH
STRIKE
CYLINDER
RETAINER
SCREWS (2)
MOUNTING
PLATE
CYLINDER HOLE
MARK THEN DRILL
Ø32mm HOLE
MOUNTING
PLATE
SCREWS (4)
SPINDLE
CASE MOUNTING
SCREWS (2)
60mm BACKSET
LEVER FURNITURE
Chisel
Phillips head screwdriver
Centre punch / nail
Hacksaw / Pliers
Pencil & ruler / measuring tape
COVER PLATE
ESCUTCHEON
PREPARE DOOR
IN
PEN
EO
WIS LATE
K
P
C
LO TEM
R
TI-C
AN DOO
LIN
CY
FIND CENTRE OF DOOR
AND MARK THEN DRILL
Ø22mm HOLE x 85mm DEEP.
FURNITURE HOLES
SPINDLE
ND
ET
KS
AC
ILL
A
ES
OL
E H FROM
UR
T
NIT OLE EVEN E.
R
FUR R H
AC
ILL INDE TO P OR F
S
L
CY SIDE OF DO
G
TH
BO TERIN
IN
SPL
DR
FU R
NIT
S
OLE
EH
UR
2.
TEMPLATE
L
RIL
ND
THE LES
O
RK
MA mm H
.5
Ø6
MARK THEN DRILL
Ø6.5mm HOLES
1.
ILL
mB
R
ND
THE LE
O
RK
MA mm H
Ø22
OLE
STOP PLATE
INSIDE
LEVER FURNITURE
FRONT DOOR PLATE
1. Select CLOCKWISE or ANTI-CLOCKWISE template to
suit door direction.
2. Place template on inside door face at required height from
floor with the fold line along the door edge.
3. Mark and drill holes as specified on template.
IDE
to
INS
late
mp
E te
om
WIS
ht fr
CK
heig
C LO
ed
INT
quir
t re .
or A
a
E
e
e
c
g
IS
KW .
or fa oor ed plate.
o
C
d
O
d
L
m
on side
e
ct C irecti
g th on te
in
Sele oor d te on e alon cified
1.
d
la
e
suit e temp fold lin as sp
e
s
c
Pla with th ll hole
2.
ri
r
floo and d
rk
Ma
3.
Separate template from installation instructions, select CLOCKWISE or
ANTI-CLOCKWISE side of template to suit door opening direction.
Fold template where indicated & position on door with tape at required height.
Mark hole positions for deadlatch, furniture and furniture latch, then remove
template prior to drilling.
Drill Ø22mm latch hole to depth of 85mm, ensuring hole is drilled squarely.
Drill 2 x Ø6.5mm & 1 x Ø22mm holes for furniture and 1 x Ø32mm and
4 x Ø3mm (depth 25mm) holes for the deadlatch.
Note: Drill Cylinder and Furniture holes from both sides of the door
to prevent splintering.
LATCH
LEVER FURNITURE SCREWS
(M4 x 65mm)
(cut to correct length if required)
Slide Latch into hole and mark around latch face plate.
Chisel out face plate area to a recess of 2.5mm. Mark and drill 2 holes for
latch screws.
Insert latch with angled face of bolt towards strike and fasten with 2 x 20mm
screws provided.
Insert spindle into latch mechanism in door. Standard spindle suits
32mm - 45mm door thicknesses, for thicker doors a special order spindle
may be used.
5072M-FRONT-170800.AI
ADOBE ILLUSTRATOR (SAVED AS VERSION 8.0)
291mm x 453mm DOUBLE SIDED
SINGLE (GRAYSCALE)
Check the required handing of the lever furniture to the door, i.e. left or right hand.
The lever furniture should always rotate downwards and spring return up. To set the
handing of the furniture:- Inside lever: Remove stop screw, rotate lever and replace
screw to handing required. External lever: Remove screw and stop plate, rotate
lever to handing required, replace stop plate and screw.
Fasten the lever furniture and front door plate to the required side of the door
with the correct length Lever Furniture screws. To ensure Lever Furniture screws
are the correct length insert the screws through the lever furniture and the door.
The end of the screws must protrude only 5mm past the external side of the
door, if required cut screws to the correct length.
PERFORATION
TEAR OFF
TEAR OFF
DRILL 2 HOLES
Ø5mm X 63mm Deep
FOLD LINE
FOLD LINE
DOOR FRAME STRENGTHENER
TEMPLATE
FOLD LINE
FOLD LINE
IMPORTANT
Connecting bar must NOT
protrude past Hub face.
TEAR OFF
60m
RH
DE
PERFORATION
R
ND
THE LE
O
RK
MA mm H
Ø32
FIN
AN D C
E
Ø2 D MANTR
2m R E
m K T OF
HO HE DO
LE N D OR
x 8 RIL
5m L
m
DE
EP
.
3
HANDING OF INTERNAL
LEVER FURNITURE.
MARK THEN DRILL
Ø22mm HOLE
L
RIL
ND
THE
EEP
RK
MA LES mm D
5
O
4H mx2
Ø3m
FOLD HERE ON DOOR EDGE
W
UP AY
G
LEVER HANDING AND ASSEMBLY
TEAR OFF
TH
IS
ASSEMBLE LATCH
2
DOOR
DRILL FURNITURE HOLES AND
CYLINDER HOLE FROM
BOTH SIDES TO PREVENT
SPLINTERING OF DOOR FACE.
LEVER
FURNITURE
SCREWS (2)
LOCK CASE
PERFORATION
TOOLS REQUIRED
Ø3.0, Ø5.0 & Ø6.5mm drill bits
Ø22mm spade bit
Ø32mm hole saw
Drill
Masking Tape
TEAR OFF
FRONT
DOOR
PLATE
LATCH
MARK THEN DRILL
4 HOLES Ø3mm x 25mm DEEP
LATCH
SCREWS (2)
DEADLATCH
STRIKE MOUNTING
SCREWS (3)
DOOR THICKNESS:
32mm to 45mm
FILENAME:
FORMAT:
PAGE SIZE:
COLOUR:
DOOR
LATCH STRIKE
MOUNTING
SCREWS (2)
BOLT HOLD BACK WITH KEY:
Prevents unauthorised 'hold back' release.
To Engage:
Rotate turn knob fully clockwise and lock in
rotated position by turning key in knob one
full turn anti-clockwise.
To Release:
Unlock turn knob by turning key one full turn
clockwise and rotate turn knob anti-clockwise.
1
FOLD HERE ON DOOR EDGE
COMBINATION LOCKSET
BOLT HOLD BACK WITHOUT KEY:
To Engage:
Rotate turn knob fully clockwise.
To Release:
Rotate turn knob anti-clockwise.
ANTI-CLOCKWISE OPENING
DOOR TEMPLATE
THIS WAY
UP
CONNECTING BAR LENGTH
TEMPLATE
PERFORATION
PREPARE LOCK
4
MARK THEN DRILL
4 HOLES Ø3mm x 25mm DEEP
CYLINDER HOLE
CYLINDER
LOCK CASE
MOUNTING
PLATE
MOUNTING PLATE
Insert cylinder, with name to top, into front door plate hole from OUTSIDE of door.
Fold and position CONNECTING BAR TEMPLATE as shown. Mark connecting
bar between the 2 lines. Remove cylinder assembly and CUT connecting bar
to length. Connecting bar must NOT protrude past HUB face or guarantee will be void.
Fix mounting plate to door with 4 x 28mm woodscrews provided.
Align Notch on HUB with 'V' on mounting plate.
Assemble cylinder assembly through door plate, ensure connecting bar engages
in hub slot.
Place 32mm cylinder retainer screw through slot in hub and secure cylinder
assembly to door.
Rotate HUB 90o by inserting key in cylinder, and secure second retainer
screw. Ensure both screws are tightened firmly.
Rotate turn knob fully clockwise to HOLD BACK position.
Remove the two case mounting screws from the lock case.
Take mounting plate out of lock case.
60mm BACKSET
DRILL FURNITURE HOLES AND
CYLINDER HOLE FROM
BOTH SIDES TO PREVENT
SPLINTERING OF DOOR FACE.
MARK THEN DRILL
Ø22mm HOLE
INSTALL CASE
6
CONNECTING BAR
TEMPLATE
HUB
MARK THEN DRILL
Ø32mm HOLE
FURNITURE HOLES
INSTALL CYLINDER AND MOUNTING PLATE
5
FOLD HERE ON DOOR EDGE
THIS WAY
UP
TEAR OFF
CLOCKWISE OPENING
DOOR TEMPLATE
INSTALL STRIKES
FIND CENTRE OF DOOR
AND MARK THEN DRILL
Ø22mm HOLE x 85mm DEEP.
7
Rotate turn knob fully clockwise to HOLD BACK position.
Ensure notch on HUB is aligned with 'V' on mounting plate. With the key
removed from the external cylinder, fit case body to mounting plate as shown.
Secure to mounting plate using the two case mounting screws.
FINAL ASSEMBLY
GUARANTEE
8
JAMB
DOOR FRAME
STRENGTHENER
TEMPLATE
3mm Max.
MARK THEN DRILL
Ø6.5mm HOLES
DOOR FRAME
STRENGTHENER
INSIDE
1. Select CLOCKWISE or ANTI-CLOCKWISE template to
suit door direction.
2. Place template on inside door face at required height from
floor with the fold line along the door edge.
3. Mark and drill holes as specified on template.
FURNITURE
LATCH
STRIKE
COVER PLATE
ESCUTCHEON
DEADLATCH
STRIKE
GUARANTEE
PERFORATION
TEAR OFF
TEAR OFF
DRILL 2 HOLES
Ø5mm X 63mm Deep
PERFORATION
FOLD LINE
DOOR FRAME STRENGTHENER
TEMPLATE
TEAR OFF
CONNECTING BAR LENGTH
TEMPLATE
FOLD LINE
PERFORATION
FOLD LINE
IMPORTANT
Connecting bar must NOT
protrude past Hub face.
TEAR OFF
FOLD LINE
Position deadlatch strike on jamb directly opposite the lock case and mark
outline of strike flange on jamb edge.
Mortice area of flange. Depth of flange mortice determines gap.
NOTE: 3mm maximum gap between lock and installed strike.
Position door frame strengthener template in strike flange mortice as
shown. Drill 2 Ø5 x 63mm deep holes for the door frame strengthener screws.
WARNING: Care must be taken when drilling and fixing screws to
jamb. Screws must NOT come in contact with electrical wires in jamb.
Install door frame strengthener and secure using 2 x 65mm door frame
strengthener screws.
Locate deadlatch strike over door frame strengthener, mark and drill 3 x Ø3
holes and fix with 28mm strike mounting screws supplied.
Locate latch strike in position, mark and mortice strike if necessary and
secure with 2 x 20mm screws supplied with strike.
NOTE: Pre-drill Ø3mm x 25mm deep for woodscrews.
Position the cover plate escutcheon firmly over the furniture.
TEST BOTH DEADLATCH AND FURNITURE LEVER ASSEMBLY FOR
CORRECT FUNCTION.
Lockwood Security Products Pty Ltd. guarantees its products against defects in workmanship
and materials. If within the normal working life of a product it is found to be defective,
Lockwood Security Products Pty Ltd will supply the same or an equivalent product free of charge.
Lockwood Security Products Pty Ltd. however, assumes no liability under this guarantee
for the following :
1. Improper installation or failure to follow fitting instructions.
2. Failure due to improper maintenance or fair wear and tear.
3. Indirect or consequential loss or damage.
4. Cost of removal and/or replacement .
5. Cost of freight and/or replacement.
6. The plated finishes Florentine Bronze, Architectural Bronze, Polished Brass and
Satin Brass are classified as soft finishes. As deterioration is possible under some
climatic conditions, these finishes are excluded from this guarantee.
Nothing in the Lockwood Security Products Guarantee excludes, restricts or modifies any
condition, warranty, right or liability implied or protected by law where to do so would render
the Guarantee, or any part of it, void.
5072M 082000
FILENAME:
FORMAT:
PAGE SIZE:
COLOUR:
5072M-BACK-170800.AI
ADOBE ILLUSTRATOR (SAVED AS VERSION 8.0)
291mm x 453mm DOUBLE SIDED
SINGLE (GRAYSCALE)