industrial parquetdesign 2.0

Transcription

v1.0 140227
Umeå Community Centre - Smoked Oak
INDUSTRIAL PARQUETDESIGN 2.0
PRODUCT INFORMATION
2
v1.0 140227
Ash Select - Grant Thornton, Visby
CONTENTS
PRODUCT DESCRIPTION
PRODUCT SPECIFICATION
TECHNICAL INSTRUCTIONS
03 PROD. DESCRIPTION
05 ASH SELECT
14 PRECONDITIONS
06 ASH RUSTIC
15 SUBSTRATE &
STRUCTURES
07 OAK SELECT
08 OAK OBJECT
09 OAK STRIPE
17 INSTALLATION INSTRUCTIONS
19 CARE INSTRUCTIONS
10 OAK RUSTIC
11 SMOKED OAK SELECT
12 SMOKED OAK STRIPE
13 ACCESSORIES
Almedals Trägolvsaktiebolag | Tel: +46 31-15 00 66 | [email protected] | www.almedalsgolv.com
3
v1.0 140227
Oak Rustic - Schenker, Göteborg
PRODUCT DESCRIPTION
PREFINISHED SOLID
INDUSTRIAL PARQUET
Design 2.0 is our latest addition
in prefinished industrial parquet
flooring.
Supplied in prefinished sections
with tongue and groove on all
sides, presanded and factoryfinished with hard wax oil. The
parquet is fully glued down to the
substrate and after the adhesive
cure time should only be installation waxed.
DESIGN 2.0 provides a finished
surface very quickly which entails
a significant time savings on the
building site.
In appearance, DESIGN 2.0 is
nearly identical to the traditional
industrial parquet, but the strips
are slightly wider. The floor is
constructed of narrow strips that
are linked on the underside with
milled-in plywood strips.
small dimensions. When fitting to
the room, the parquet sections can
be sawn with a bandsaw or jigsaw,
which entails significant time savings in connection with installation.
The parquet is supplied in finished
sections, 7.8 mm thick, 632 mm
long x 312 mm wide. Because
the strips are not glued together,
they can expand and dry with no
risk of so-called side-gluing. The
joined floor sections contribute
to greater and better adhesion to
the substrate and parquet adhesive. The risk of strip separation is
consequently very low compared
with ordinary industrial parquet of
The parquet is fully glued down to
the substrate, which also provides
very good room acoustics.
The parquet is ideal for gluing to
panels or directly on walls as an
accent wall or similar.
The parquet is installed descending in one direction, but the direction can also be turned since the
tongues and grooves fit on both the
long and short sides.
4
v1.0 140227
Oak Stripe - Kullavik Montessori School
PRODUCT DESCRIPTION
DESCRIPTION
SECTION SIZE
THICKNESS 7.8 mm
WIDTH 312 mm
LENGTH 632 mm
GRADE
See separate grade specifications per
wood species.
PRESANDED
DESIGN 2.0 is supplied with a presanded
and factory-finished surface. Filling occurs.
The parquet is fully glued down to the
MANUFACTURING
TOLERANCES
Minor differences in level of approx. 0.5
mm. Gaps of max approx. 1.0 mm.
HEAT RESISTANCE
0.050 m2 K/W
STRIP SIZES
substrate and after the adhesive cure time
THICKNESS 7.8 mm
WIDTH 22 mm
LENGTH 156 mm
FIRE CLASSIFICATION
should only be installation polished.
Euroclass Cfl-s 1 (floors in escape routes,
Class G) per EN 14342 5.1 for oak and
smoked oak.
For other woods, Dfl-s 1.
MOISTURE CONTENT
8 (±2)%
WOOD SPECIES
SURFACE FINISHING
Supplied hard wax oiled, neutral or
pigmented. Can also be supplied with
a brushed surface. Please refer to the
website for information about current
surface finishes.
Ash, Oak and Smoked Oak
We can also produce in other woods as
preferred.
5
v1.0 140227
PRODUCT DESCRIPTION
ASH SELECT
THE COMPANY
APPEARANCE
SURFACE FINISHING
Almedals Trägolvsaktiebolag
Storgatan 1, 434 30 Kungsbacka, Sweden
T: +46 (0) 31–150066, F: + 46 (0) 300–18173
Virtually free of knots and hearts.
Consistently graded. Very small knots may
occur.
pigmented. Can also be supplied with a
brushed surface.
COLOUR SHADING
COMPOSITION
Yes, the natural colour variations of the
wood.
HAZARDOUS SUBSTANCES
PRODUCT DESCRIPTION
WOOD SPECIES
Ash
none
HEARTWOOD
Virtually free of brown heart.
COUNTRY OF ORIGIN
PVAC white glue
Central Europe
DIMENSIONS
MOISTURE CONTENT
THICKNESS 7.8 mm
WIDTHS 312 mm
LENGTHS 632 mm
8% (± 2)
OTHER SUBSTANCES
INSTALLATION
Fully glued down to the substrate.
FILLING
Filler may be used. Note that the colour of
the filler may differ from knots and wood.
6
v1.0 140227
PRODUCT DESCRIPTION
ASH RUSTIC
THE COMPANY
APPEARANCE
SURFACE FINISHING
T: +46 (0) 31–150066, F: + 46 (0) 300–18173
With brown heart and knots. Unlimited.
brushed surface.
COLOUR SHADING
wood.
PRODUCT DESCRIPTION
WOOD SPECIES
Ash
COUNTRY OF ORIGIN
Central Europe
MOISTURE CONTENT
8% (± 2 )
HEARTWOOD
Brown heart not limited.
COMPOSITION
none
DIMENSIONS
THICKNESS 7.8 mm
WIDTHS 312 mm
LENGTHS 632 mm
OTHER SUBSTANCES
FILLING
INSTALLATION
the filler compound may differ from knots
and wood.
PVAC white glue
7
v1.0 140227
PRODUCT DESCRIPTION
OAK SELECT
THE COMPANY
APPEARANCE
SURFACE FINISHING
T: +46 (0) 31–150066, F: + 46 (0) 300–18173
Our most consistent grade. Virtually free of
knots and sapwood.
brushed surface.
COLOUR SHADING
PRODUCT DESCRIPTION
wood.
COMPOSITION
WOOD SPECIES
SAPWOOD
Oak
Virtually free of sapwood.
none
COUNTRY OF ORIGIN
DIMENSIONS
OTHER SUBSTANCES
Central Europe
THICKNESS 7.8 mm
WIDTHS 312 mm
LENGTHS 632 mm
PVAC white glue
FILLING
MOISTURE CONTENT
8% (± 2 )
INSTALLATION
and wood.
8
v1.0 140227
PRODUCT DESCRIPTION
OAK OBJECT
THE COMPANY
APPEARANCE
SURFACE FINISHING
T: +46 (0) 31–150066, F: + 46 (0) 300–18173
Mainly clean and with isolated nots.
Isolated sections with heartwood or
sapwood allowed. Greater colour and
shade differences than with Select.
brushed surface.
PRODUCT DESCRIPTION
COLOUR SHADING
COMPOSITION
WOOD SPECIES
wood.
Oak
COUNTRY OF ORIGIN
Central Europe
MOISTURE CONTENT
8% (± 2 )
None.
SAPWOOD
Allowed to a limited extent.
OTHER SUBSTANCES
PVAC white glue
DIMENSIONS
THICKNESS 7.8 mm
WIDTHS 312 mm
LENGTHS 632 mm
INSTALLATION
FILLING
and wood.
9
v1.0 140227
PRODUCT DESCRIPTION
OAK STRIPE
THE COMPANY
APPEARANCE
SURFACE FINISHING
T: +46 (0) 31–150066, F: + 46 (0) 300–18173
A grade that is based on the contrast
between heartwood and sapwood. Mainly
knot-free.
brushed surface.
COLOUR SHADING
PRODUCT DESCRIPTION
WOOD SPECIES
Oak
wood.
SAPWOOD
COMPOSITION
None
Unlimited.
COUNTRY OF ORIGIN
Central Europe
DIMENSIONS
MOISTURE CONTENT
THICKNESS 7.8 mm
WIDTHS 312 mm
LENGTHS 632 mm
8% (± 2 )
OTHER SUBSTANCES
PVAC white glue.
INSTALLATION
FILLING
and wood.
10
v1.0 140227
PRODUCT DESCRIPTION
OAK RUSTIC
THE COMPANY
APPEARANCE
SURFACE FINISHING
T: +46 (0) 31–150066, F: + 46 (0) 300–18173
A rustic grade that contains knots,
heartwood zones and sapwood to a
certain limited extent.
brushed surface.
COLOUR SHADING
PRODUCT DESCRIPTION
WOOD SPECIES
Oak
wood.
SAPWOOD
COMPOSITION
no
Allowed to a limited extent.
COUNTRY OF ORIGIN
Central Europe
DIMENSIONS
MOISTURE CONTENT
THICKNESS 7.8 mm
WIDTHS 312 mm
LENGTHS 632 mm
8% (± 2 )
OTHER SUBSTANCES
PVAC white glue.
INSTALLATION
FILLING
and wood.
11
v1.0 140227
PRODUCT DESCRIPTION
SMOKED OAK SELECT
THE COMPANY
APPEARANCE
SURFACE FINISHING
T: +46 (0) 31–150066, F: + 46 (0) 300–18173
Our most consistent grade of smoked
oak. Virtually free of knots and sapwood.
Isolated sections with sapwood and very
small knots may however occur.
brushed surface.
PRODUCT DESCRIPTION
COLOUR SHADING
COMPOSITION
WOOD SPECIES
wood.
Smoked Oak
COUNTRY OF ORIGIN
Central Europe
MOISTURE CONTENT
8% ( ± 2 )
SMOKING
Ammonia gas in a closed kiln.
no
SAPWOOD
Virtually free of sapwood.
OTHER SUBSTANCES
Ammonia gas in manufacturing.
DIMENSIONS
THICKNESS 7.8 mm
WIDTHS 312 mm
LENGTHS 632 mm
INSTALLATION
FILLING
and wood.
12
v1.0 140227
PRODUCT DESCRIPTION
SMOKED OAK STRIPE
THE COMPANY
APPEARANCE
SURFACE FINISHING
T: +46 (0) 31–150066, F: + 46 (0) 300–18173
A rustic grade that contains knots,
heartwood zones and sapwood.
brushed surface.
COLOUR SHADING
PRODUCT DESCRIPTION
wood.
COMPOSITION
WOOD SPECIES
SAPWOOD
Smoked Oak
Unlimited.
no
COUNTRY OF ORIGIN
DIMENSIONS
OTHER SUBSTANCES
Central Europe
THICKNESS 7.8 mm
WIDTHS 312 mm
LENGTHS 632 mm
Ammonia gas in manufacturing.
FILLING
MOISTURE CONTENT
8% ( ± 2 )
SMOKING
Ammonia gas in a closed kiln.
INSTALLATION
and wood.
13
v1.0 140227
ACCESSORIES 2.0
END PIECES
STAIR NOSES
THRESHOLDS
14
v1.0 140227
Ash Rustic - Lector Office
PRECONDITIONS
SUB-FLOOR LEVELNESS
Standard requirements as set forth in AMA
Hus 11.
SUB-FLOOR MOISTURE
CONTENT
Wood: Must not exceed moisture content
of 12% or 65% RH.
Concrete: Note that RH must always be
measured in concrete substrates. This
applies even to older concrete substrates.
When fully gluing to concrete without cast
substrate heating, the core test must be
below 85% RH.
When fully gluing to concrete with
substrate heating, a moisture barrier must
be installed over the concrete before
gluing.
SUB-FLOOR
GENERAL CONDITIONS
Clean, level, free of dust, grease and dirt.
ROOM TEMPERATURE
18-22°C
ROOM HUMIDITY
30-60% RH
SUB-FLOOR TENSILE
STRENGTH IN CONNECTION
WITH FULL GLUING
1.5 MPa
LEVELLING/LIQUID FILLER
The levelling compound must be at least
2 mm thick and have a minimum tensile
strength of 1.5 MPa. Normal drying filler
and levelling compounds must be used.
FLOOR HEATING
Refer to Swedish Flooring Trade
Association guidelines.
USAGE VALUES
Room temperature: 15-30°C
Room humidity: 30-60% RH
15
v1.0 140227
Oak Stripe - Cardcon Medical Practice
SUBSTRATE & STRUCTURES
WOOD JOISTS
PLYWOOD, FLOATING
FULL GLUING ON CONCRETE
Centre to centre distance 600 mm.
Covered with 22mm particle board laid
crosswise, glued and screwed down.
DESIGN 2.0 is fully glued down to the
particle board in any direction.
Poured concrete slab with max RH of 90%
is covered with age-proof plastic laid with a
minimum overlap of 20 cm. Birch plywood,
min 9 mm, is laid floating against the
substrate and covered with another layer
of 9 mm birch plywood, which is glued
flush to the first layer of plywood using
parquet adhesive.
The two layers should be installed with
an overlap and screwed or stapled down.
DESIGN 2.0 is fully glued down to the
plywood in any direction.
See Hus AMA KEB.234, 2341, 2342
Note that RH must always be measured in
concrete substrates. This applies even to
older concrete substrates.
EXISTING PLANK FLOOR
Should be sanded level on the diagonal
using a floor sanding machine and 16 grain
sandpaper. Cover thereafter with birch
plywood, min 4 mm, which is fully glued
down flush against
the substrate using parquet adhesive. The
plywood must be fully glued down to the
plank floor and either screwed down or
stapled. DESIGN 2.0 is fully glued down to
the plywood in any direction.
PARTICLE BOARD, FLOATING
Poured concrete slab with max RH of 90%
is covered with age-proof plastic laid with a
minimum overlap of 20 cm. 22 mm flooring
particle board is laid floating over the
substrate. DESIGN 2.0 is fully glued down
to the particle board in any direction.
See Hus AMA KEJ 234
MDF PANELS
Must be fully glued down to the substrate
to be used as a sub-floor. DESIGN 2.0 is
fully glued down to the MDF board in any
direction.
When fully gluing to concrete without cast
substrate heating, the core test must be
below 85% RH.
When fully gluing to concrete with substrate
heating, a moisture barrier must be installed
over the concrete before gluing.
If the concrete floor is above warm or cool
spaces such as a boiler room, sauna, or
unheated garage, glue bonding cannot be
performed. In these cases, age-proof plastic
is required below floating particle board
or plywood. See Hus AMA KEB.234, 2341,
2342 and KEJ 234
FULL GLUE-DOWN ON
GROUND SLAB
The RH of the concrete must not exceed
85%. The concrete must be protected
against moisture migration from below.
Contributing moisture is not allowed.
16
v1.0 140227
SUBSTRATES & STRUCTURES
FLOOR LEVELLED WITH LIQUID
FILLER
NEEDLEPUNCH OR WALL-TOWALL CARPET
The levelling compound must be at least
2 mm thick and have a minimum tensile
strength of 1.5 MPa. Normal drying filler
and levelling compounds must be used.
Not approved as a substrate for gluing.
VINYL OR LINOLEUM FLOORING
CELLULAR PLASTIC
(EPS, EXPANDED POLYSTYRENE)
IMPACT NOISE REDUCTION
A specially designed cork-PU mat can
be fully glued down to concrete, particle
board, or plywood. DESIGN 2.0 is
thereafter glued to the mat. Impact noise
improvement: EN ISO 140-8 17 dB.
See floating particle board.
Normally not approved as a substrate for
gluing.
GYPSUM
STONE OR TILE
FLOOR HEATING
General: The surface is sanded or
roughened with sandpaper. Solvent-based
parquet adhesive is used for gluing. If the
stone/tile has been treated with polish or
comparable, there is risk that the adhesive
will separate from the substrate in spite of
the sanding.
NOTE In these cases, you should contact
the adhesive manufacturer directly.
There are no technical barriers to
combining DESIGN 2.0 with subfloor
heating.
Not approved as a substrate for gluing.
VENTILATED SUBFLOOR
(of the Granab and Nivell System types).
One layer 22 mm flooring particle board,
installed crosswise, glued together and
attached to the studs to which DESIGN 2.0
is glued.
FACTORY INSTALLED IMPACT
NOISE REDUCTION
DESIGN 2.0 can also be supplied factory
installed on a cork-PU mat.
Impact noise improvement:
EN ISO 140-8 17 dB.
ADHESIVE TYPE
The adhesive supplier should always
be consulted about gluing down wood
flooring to the substrate.
EcoSimp Flooring (Swan eco-labelled) may
be a suitable adhesive.
17
v1.0 140227
Smoked Oak Select - Scandic South Harbour, Copenhagen
INSTALLATION INSTRUCTIONS
You must read Almedals installation
instructions before you begin the installation. If you are unsure about anything, you
must contact Almedals before the work is
begun.
INSTALLATION
Installation direction: We recommend that
the strips are laid crosswise to the source
of natural light.
Before the floor installation is begun, you
must check that the substrate is level and
meets standard requirements set out in
AMA Hus 11.
The floor is not limited as to the size of
contiguous surfaces that may be installed.
However, the floor should not be glued
over any movement joints in the underlying
concrete floor.
Check that the temperature in the room is
about 20 degrees Celsius at 30-60% relative humidity.
Snap out two start lines equal to two parquet rows, 624 mm.
Check that the packages are labelled with
the right floor before they are opened.
Note that the floor must be installation
waxed before it is used. It is also important
that the floor is not cleaned with water
during the first 2 weeks before the wax is
cured.
HANDLING
PACKAGES
DESIGN 2.0 is delivered in sealed plastic
packaging.
STORAGE
Store the packages unopened until they
are installed. The parquet must have had
enough time to adjust to the room temperature of approx. 18-22 degrees C before it
is installed.
Remember that the lines should be about 1
cm inside the edge of the parquet section.
This prevents the glue from sticking out
alongside the last row and drying under
the tongue.
NOTE Note that the glue quantity required
of 1 litre (approx. 1.5-1.6 kg) per m2 may
cause problems in installation because it
may be more difficult to joint the tongues
and grooves in the floor section because
there is vertical movement in the glue. The
glue can also be pressed sideways outside
the floor section. As a result, glue may
end up between tongues and grooves. Be
careful to check that glue has not been
pressed out under the tongue and allowed
to cure before installation of the next
row is begun. Installation is considerably
simplified with application of 0.5-0.6 litres
(approx. 0.8-1.0 kg) per m2.
Do not glue larger surfaces than you have
time to install before the glue begins to
dry. The open time of the glue varies
according to types and conditions.
Open at least 2-3 packages and distribute
the sections before installation. This is
done to ensure a correct result where the
appearance of the parquet varies among
the rows.
Remember to lock the sections on the
short side against the wall using wedges
or similar so that they cannot slide apart.
Spread out the sections and distribute
them based on appearance and flatness.
If you are going to install a convex or concave section, the next section must be flat.
If two convex sections are installed next to
each other, the convexity will be permanent even after the glue has cured.
Fit the section at the short end first and
then fit the long side. Avoid fitting them
sideways, short side to short side, as this
will lead to the glue ending up between
the sections, with gaps as a result.
Install the next row offset (min 15 cm) to
create a brickwork pattern. The parquet
should not be installed side by side with
no offset. Thereafter, each section is
installed one after the other. The part cut
off at the wall is used as the starting piece
of the next row.
18
v1.0 140227
Oak Object surface finish 1401 - Friskis o Svettis Fitness Centre, Lidingö
INSTALLATION INSTRUCTIONS
You should roll the parquet before the glue
has cured.
The first and last rows must be wedged
against the walls while the glue is curing
to prevent the parquet from sliding apart.
Leave an expansion gap of approx. 5-10
mm from all permanent fixtures.
The parquet can usually be sawed with a
jigsaw if two guide strips remain. If there is
only one guide strip left, the strips will slide
apart and separate. In these cases, the
section must be held together with tape
while it is being sawn. Lay the section on a
table or comparable while you are sawing
it. An alternative is to use a portable bandsaw that can be used to saw the section in
different directions.
If you will be making straight cuts, along
walls for example, the section should
instead be laid on a board and sawn with a
circular saw fitted with a guide bar.
If the section is sawn along a wall or
similar, the strips may be serrated on the
vertical. See illustrations below.
In these cases, use a straight edge or
comparable to press the strips down to a
level surface.
Avoid walking on the parquet other than
in exceptional cases because it can easily
slide apart, especially if you walk with long
steps.
Note that the floor should be installation
waxed using SAICO or OSMO maintenance wax and a red polishing pad before
it is used. It is also important that the floor
is not cleaned with water during the first 2
weeks before the wax is cured.
19
v1.0 140227
CARE INSTRUCTIONS
INSTALLATION FINISHING
Note that the floor should be installation
waxed using SAICO or OSMO maintenance wax and a red polishing pad before
it is used. It is also important that the floor
is not cleaned with water during the first 2
weeks before the wax is cured.
GENERAL ADVICE
Stop the dirt at the entrance. For this reason, you should always have an effective
doormat inside the exterior door and, if
possible, outside as well. Keep the temperature and humidity as constant as possible to avoid excessive movements in the
flooring material. Protect the wood floor
against all types of liquids. Wipe up any
spills immediately. Felt or Teflon (special)
protective pads - but not metal - should be
fitted to furniture.
CLEANING
Make it a regular routine to remove visible
soiling such as dust, crumbs, gravel, etc.
Vacuum cleaning, sweeping, or dry mopping will remove most dry particles. Damp
mopping with a very lightly damp cloth or
mop may be done as needed. Dry mop
immediately afterwards! - Never leave a
damp area on an oiled wood floor. When
you are damp mopping an oiled floor, it is
a good idea to add an oil-refreshing soap
cleaner to the water.
Oil-refreshing floor soap has an oil content
of 20-30% and should not be compared
to ordinary yellow or green soap. A pH
neutral cleaning product should be used
on varnished floors.
1. Always try a weak soft soap solution first
and rub the spot with a cloth or scouring
pad.
MAINTENANCE OF HARD WAX
OIL FINISHED WOOD FLOORS
DANGER OF FIRE!
A hard wax oil-finished floor should be
regularly maintained. After thorough
cleaning, supplement the base finish with
another coat of hard wax oil that cleans
and adds a new layer of protection to the
floor. The frequency of maintenance varies
considerably depending upon the use of
the room. Various suppliers of hard wax oil
offer different solutions for cleaning and
maintenance oiling.
In public spaces, combined sweeper/
scrubber/drier machines are often used to
advantage with re-oiling wood floor soap.
2. If necessary, switch the soap solution for
a cleaning product recommended by the
supplier of the surface finishing system.
Organic materials such as cloths, paper
polishing pads, etc. that have been in
contact with floor oil based on linseed oil
must always be placed in water immediately after use to prevent spontaneous
combustion.
SPOT REMOVAL
Remove spots before they have dried
into the floor. If necessary, wipe the area
afterwards with clean water. Use a slightly
damp cloth. Excess water, strong alkaline
cleaning products and strong solvents
damage wood floors.

industrial parquetdesign 2.0

Transcription

Similar documents

industrial parquetraw

Desideration

Fact sheet - Casuarina glauca / Swamp Oak

Premium Wood Stain Brochure - Rust

Huyard N Flyer - Upper Yampa Realty

viña altamar - Hammeken Cellars

DINING - Hülsta

LA PUERTA Reserva Tech Sheets

Reclaimed Hardwoods - Keim Lumber Company

Pog Mo Thoin Data Sheet