by AAC - Phastek Performance

2010 - * Chevrolet Camaro V8/SS
by A A C
Package # 320-100R...Fits V8/SS Camaro
NOTE: Not designed to fit V6/RS Camaro
HARDWARE Enclosed:
1 “B” Bag “large screws” for attachment in the wheel wells
1 “C” Bag “small screws” for attachment in the step plate/door jams
1 Tube Polyurethane adhesive for added adhesion
4 “L” brackets for wheel well mounts
6 ABS “hanging ledges”, w/double sided tape, for Rear Air Dam
TOOLS required/optional:
Box cutter/razor knife
Caulk Gun
Drill bit—1/8”
Phillips screwdriver
Power drill (cordless suggested)
Optional:
80 grit sandpaper (for fine fit adjustments)
Black undercoating (for painting wheel wells)
Masking tape (for painting wheel wells)
Pop rivets
Pop rivet gun
Page 1 of 10
INSTALLATION INSTRUCTIONS
Thank you for purchasing our RAZZI by A.A.C. Ground Effects Package. If you have any
installation questions about your Ground Effects package, please call
RAZZI by A.A.C.
(800) 235-6087
PLEASE REVIEW THESE INSTALLATION INSTRUCTIONS COMPLETELY BEFORE
YOU BEGIN INSTALLING YOUR GROUND EFFECTS PACKAGE.
NOTE: Please read the attached “INSTALLATION TIPS” that describe additional recommended adhesives (beside the tube of polyurethane and the two-sided tape that has already
been attached at the factory and is included with your package).
Installation Note: As a rust preventative, be sure to place a small “dab” of the polyurethane adhesive provided with your
package into any hole drilled thru body sheet metal prior to attaching a screw.
IMPORTANT: Use a good AUTOMOTIVE GREASE AND WAX CLEANER to clean your
vehicle in all areas where our RAZZI by A.A.C. Ground Effects parts are to be attached.
RAZZI by A.A.C recommends that you “scuff” the areas of your vehicle where the Ground
Effects parts are going to be attached with a “Scotch Brite pad and the automotive grease
and wax cleaner”. Many new vehicles are delivered with a coating/wax on the vehicle that
includes teflon products. These wax/teflon products will prevent adhesion of your RAZZI
Ground Effects parts and MUST be cleaned off the vehicle before your RAZZI by A.A.C
Ground Effects packages is installed.
CALL RAZZI by A.A.C FOR OTHER GROUND EFFECTS PACKAGES, SPOILERS,
AND ACCESSORIES AT (800) 235-6087 or VISIT US AT OUR WEBSITE,
www.RAZZI.com
TO SEE A COMPLETE CATALOG OF RAZZI by A.A.C GROUND EFFECTS PACKAGES.
CALL CALIFORNIA DREAM BY A.A.C FOR SPOILERS, GROUND EFECTS PACKAGES, AND ACCESSORIES AT (888) 288-6391 or VISIT OUR WEBSITE,
www.CALIFORNIA-DREAM.com
TO SEE A COMPLETE CATALOG OF CALIFORNIA DREAM by A.A.C SPOILERS
AND ACCESSORIES.
Page 2 of 10
Page 3 of 10
Preparation -
Lift car with floor jack .
Install jack stands and support car.
Remove tires.
Set tires off to the side and clear of car
Remove floor jack from under car.
Page 4 of 10
Front Air Dam -
Pre-fit Front Air Dam.
With FAD in position, use a pencil to mark
the fascia where the FAD goes into the
wheel well.
Drill a 1/8” pilot hole for locating the 90 ◦
ABS fascia support bracket...approx 3/8”
in and 1” below the pencil mark.
Locate the 90◦ support bracket on the back
side of the fascia approx 1/4” below the
pencil mark and flush with the back edge
of the fascia.
Install a black screw thru the hole in the
fascia and into the 90◦ support bracket.
Drill a second 1/8” pilot hole in the fascia
approx 1” below and 3/8” “in” below the
upper hole.
Install a second black screw thru the hole in
the fascia and into the 90◦ support bracket.
Run a small bead of urethane adhesive
across the front fascia approx 1/2” in front
of the black grill.
Put a marble sized ball of urethane adhesive under each driving light.
Install Front Air Dam taking care not to get
any of the urethane adhesive on the painted
surfaces.
Firmly press down on Front Air Dam lip in
the grill area applying pressure to urethane
adhesive applications.
While holding the FAD firmly up to the
OEM fascia, drill a 1/8” hole thru the FAD
wheel well flap and into the 90◦ support
bracket.
Page 5 of 10
Install a black screw thru the hole and into
the 90◦ support bracket.
Drill a 1/8” hole below the top screw thru
the FAD wheel well flap and into the 90◦
support bracket.
Install a black screw thru the bottom hole
and into the 90◦ support bracket.
Side Skirts -
Remove the weather stripping from the
door jam / step plate area.
Install the Side Skirt in place on the side of
the car and line up in correct position
Page 6 of 10
Prefit Side Skirts between wheel wells to
insure fit and correct side choice.
Visually line up the OEM hole (screw removed earlier) and drill an 1/8” pilot hole.
Drill a 1/8” pilot hole thru the Side Skirt
and inner fender liner.
Install a black screw thru the pilot hole and
OEM inner fender liner.
Install a small black screw thru the Side
Skirt and door jam.
While pushing in and down on the Side
Skirt drill a couple more 1/8” pilot holes.
Remove the lower OEM screw in the rear
of the front wheel well - to be reinstalled
later.
Reinstall the black OEM screw removed
earlier thru the pilot hole and into the OEM
hole.
Firmly push the Side Skirt down and in to
the door jam/step plate area and drill a 1/8”
pilot hole thru the Side Skirt and the door
jam.
While pushing in and down on the Side
Skirt install small black screws in the pilot
holes drilled.
Page 7 of 10
Remove the upper OEM screw in the front
of the rear wheel well - to be reinstalled
later.
Reinstall the black OEM screw removed
earlier thru the pilot hole and into the OEM
hole.
Visually line up the upper OEM hole
(screw remove earlier) with the drill bit.
Drill a 1/8” pilot hole thru the Side Skirt
and inner fender liner.
Firmly push the Side Skirt in place and
drill a 1/8” upper pilot hole thru Side Skirt
wheel well return lined up w/factory screw
hole
Install a black screw thru the pilot hole and
OEM inner fender liner.
Rear Air Dam -
Page 8 of 10
Install ABS hanging ledges—9 5/8” below each
OEM side marker.
Install 4 ABS hanging ledges 1” below the
design line evenly spaced out across the
OEM rear bumper cover.
With RAD in position, use a pencil to mark
the fascia where the RAD goes into the
wheel well.
Drill a 1/8” pilot hole for locating the 90◦
ABS fascia support bracket...approx 3/8”
in and 1” below the pencil mark.
Drill a second 1/8” pilot hole in the fascia
approx 1” below and 3/8” “in” below the
upper hole.
Install a second black screw thru the hole
in the fascia and into the 90◦F support
bracket.
Put a couple of marble sized balls of urethane adhesive on each corner of the RAD
being sure they clear the hanging ledges.
Put 4-6 marble sized globs of urethane
adhesive across the center section of the
RAD being sure they clear the hanging
ledges.
Install the RAD onto the OEM rear fascia.
While holding the RAD firmly up to the
OEM fascia, a drill a 1/8” hole thru the
RAD wheel well flap and into the 90◦
support bracket.
Prefit the Rear Air Dam.
Locate the 90◦ support bracket on the back
side of the fascia approx 1/4” below the
pencil mark and flush with the back edge
of the fascia and install black screw.
Page 9 of 10
Install a black screw thru the hole and into
the 90◦F support bracket.
Drill a 1/8” hole below the top screw thru
the FAD wheel well flap and into the 90◦
support bracket.
Install a black screw thru the lower hole
and into the 90◦ support bracket.
Exhaust Tips The 4” exhaust tip installed on the V8 / SS
Camaro’s by the OEM, at the factory, is
new to production built cars in the United
States. While we continue to search, we
have not found an aftermarket tip that
“perfectly” extends this large tip by simply
tightening 3 adjuster screws.
However, several of the Professional
Installers who regularly install RAZZI by
AAC Ground Effects products have used
our polished stainless steel tips and have
shared their “work arounds” to make their
best choice of tips work with the OEM
exhaust...
One Installer suggested that the 3 each 1/2”
long bolts that come installed in the
aftermarket tips be replaced with longer
bolts available at any hardware store. The
replacements should be metric—
M6x1.0x40 bolt.
Another Installer suggested “moving” each
of the “factory mounting” slots and bolt
holes towards the exit end of the
aftermarket exhaust tip by 2”. He drilled
and tapped the holes and used a grinder to
easily “cut” the slots.
Installation Tips:
Where contrasting body colors show thru the
RAZZI Ground Effects design holes, use a can
of black “Undercoating Paint” to make the factory colors blend into the design.
Page 10 of 10
When small “gaps” can be seen, use some 80
grit sandpaper to back-sand the small point that
holds the Ground Effects part off the vehicle.
In a tag area, screws can sometimes be used to
hold the Rear Air Dam tighter up to the vehicle
without holding the tag off the car in the tag
indention.
Enjoy the Ride!!!
RAZZI by A.A.C
1050 Branch Drive
Alpharetta, GA 30004
(800) 235-6087