THREADED ROD SUSPENDED MOUNTING

Transcription

THREADED ROD SUSPENDED MOUNTING
NOTES
Managing Environments™
INDUSTRIAL CURTAINS
INSTALLATION INSTRUCTIONS
THREADED ROD
SUSPENDED MOUNTING
GETTING STARTED
Open all carton(s) containing hardware and remove all items.
Position the hardware on the floor under the opening. Next,
look in the box containing the curtain(s).
Allow the curtain(s) to reach room temperature
(above 50°F/10°C) before unfolding.
The width and height of the curtain will be listed on a tag
attached to the curtain.
Managing Environments™
Phone: 800.888.9750
Fax: 412.787.3665
5350 Campbells Run Road • Pittsburgh, PA 15205
www.tmi-pvc.com • E-Mail: [email protected]
Copyright © 2013
Catalog Number
II-ICTRM-07-13
WHAT IS INCLUDED IN YOUR CURTAIN KIT
Please check the chart below to make sure you have the correct number of items.
Threaded Rod
Track Splice
Connector
Straight Track
Double
Threaded Rod
Splice Connector
Total
Length
Custom Pieces
DTRSC-16
TRTSC-16
Threaded Rod
Corner
Connector
90°
TRCC-16
Universal
Mounting
Bracket
UCMB-16
Threaded Rod
Three Way
Connector
TRTWC-D-16
Threaded Rod
Track
Connector
TRTC-16
INSERTING ROLLERS WITH HOOKS
1. Place each roller into the open end of the track. The number of rollers
must be equal to the number of grommets on the top edge of the
curtain.
1
2. Affix the second End Stop to
2
the open end of the track.
End Stop
ES-16
Step 6
Double Track
Splice
Connector
Straight Splice
Connector
HANGING THE CURTAIN
Place each curtain grommet over a roller hook and mounting is complete.
The dull side with the logo is the front and should face to the outside.
DTSC-16
Ceiling Support
Connector
Step 5
SSC-16
Curved Track 90°
Beam Flange
Clamp
CC-90-16
CSC-16
Steel Ball
Bearing
Roller with
1” Hook
SR-16-1
4 Wheel,
Steel Ball
Bearing
Roller with
1” Hook
HDSR-16-1
BFC-16
Curtain(s) with
Grommets
Nylon
Roller with
1” Hook
NR-16-1
2 Wheel
Roller with
Connector
P-SW-16
2
Number of
Curtains
7
End
Stop
End
Stop
IMPORTANT
Step 4
Allow the curtain(s) to reach room temperature
(above 50°F/10°C) before unfolding.
ATTACHING THE TRACKS
For convenience and ease of attaching the tracks to the Track Connectors,
already in place on the rods (Step 3), disassemble your configuration into
manageable sections.
NOTE: The installer will need an assistant to mount your curtain(s).
TRACK CONFIGURATIONS
End Stop
In Place
The hardware for the Threaded Rod Suspended Mounting Method allows for a
large number of configurations and is only restricted by the location of roof trusses
or beams. The 3 corner joints and straight run are shown here. WALL with DOORWAY OPENING
NOTE: Leave one of the
End Stops off the end of
the track assembly.
End Stop
Removed
Straight Splice Connector
Universal Mounting Bracket
Wall Mount Track Connector
Straight Track
with Ceiling Support
Connector
or
Universal Mounting Bracket
Curved
Track Connector
90° with Ceiling Support Connecto
or Threaded Rod
Track
Track Splice Connector
Universal
Mounting
Bracket
with
Ceiling
Support
Connector
Threaded Rod
Track
Connector
End
First, place the track into the
Track Connector.
End
Stop Stop
Straight Run
“T” Joint
Then, place the Support Plate
and secure with a nut.
“T” Connector
Corner Joint
Corner Connector 90°
WALL with DOORWAY OPENING
Support Plate
Straight Splice Connector
Support Plate Nut
Wall Mount Track Connector
or
Curved Corner Joint
Universal Mounting Bracket
Straight Track
Curved Track 90°
Curved Track 90°
End
Stop
with Ceiling Support Connector
End
Stop
WALL with DOORWAY OPE
Plan Views
Straight Splice Connector
Straight Track
TIP: Do not fully tighten the nut.
This will allow you to easily make
final adjustments to the hardware
assembly.
Curved Track 90°
End
Stop
DESIGNING A PLAN
Of course, firmly tighten all nuts
once the entire assembly is in
place.
Splice
Connector
The design of your curtain assembly will be determined by the position of the roof
trusses or beams. How you attach the threaded rods to the trusses is your
decision; however, we recommend using Beam Clamps. Threaded rods can easily
be attached to the clamps and quickly adjusted for height requirements.
If the track is being placed into a Splice Connector,
loosen the 2 allen screws just one and a half turns,
insert the track and tighten the allen screws.
TIP: When inserting Track into a Splice Connector,
lightly clamp a pair of vice grips onto the Track
about 4” from the end. This should narrow the
Track allowing easier insertion.
Roof Trusses
Ideally there should be 3’ or less between
clamps with suspended threaded rods,
but the span between trusses could be
slightly greater than 3’.
Beam Clamps
*
6
End
Stop
*
*
*
*
*
*
3’
*
*
*
*
*
*
Beam Clamps
*
Roof Trusses
From your design, measure and
position the Beam Clamps
*
- IMPORTANT -
Beam Clamps (unless ordered),
Threaded Rods, Nuts and Washers are
NOT included with your Curtain Kit.
3’
3
Wall Mount
Universal M
with Ceiling S
Step 1
2
TIP: When inserting
Track into a Splice
Connector, lightly clamp
a pair of vice grips onto the Track
about 4” from the end. This should
narrow the Track allowing easier
insertion.
TRTSC-16
1
2. Attach an End Stop to
just one open end.
THREADED ROD
TRACK
CONNECTOR
To determine the length of the threaded rods
use the following formula:
Distance from Floor to Bottom of Truss or Beam
– Overall Assembly Height + 2”
Top of
Curtain
= Length of Threaded Rods
Next, cut all the Threaded
Rods to the proper length.
CURTAIN
1”
The same steps should be taken
if Double Track hardware is
being used.
FLOOR
Step 3
ATTACHING THREADED RODS and TRACK CONNECTORS
Step 2
MEASURING FOR MOUNTING
The total height of
the assembly
includes the height
of the curtain, the
height of the
hardware plus an
additional 1” to
keep the curtain
above the floor. A
tag on your
curtain(s) should
show the overall
dimensions.
The hardware
height is shown on
the drawings to the
right.
THREADED
ROD
2”
Overall Assembly Height
SSC-16
1. Insert the two Straight Tracks into the Connector
and tighten the screws. Repeat this process until
all pieces of track are spliced together.
Distance from Floor to Bottom of Truss or Beam
Loosen the 2 allen screws on each
Splice Connector, one and a half turns.
Length of
Thrteaded Rod
BOTTOM OF
ROOF TRUSS
BEAM FLANGE CLAMP or
OTHER SUPPORT HARDWARE
SPLICING MULTIPLE TRACKS TOGETHER
Universal
Mounting Bracket
with Ceiling Support
Connector
Threaded Rod
Track Connector
Threaded Rod
Track Splice
Connector
5 3/8”
1
2
BOTTOM OF
ROOF TRUSS
BEAM FLANGE CLAMP or
OTHER SUPPORT HARDWARE
5 3/8”
THREADED
ROD
5 3/8”
THREADED ROD
TRACK
CONNECTOR
3
1”
1”
1”
Curtain Height + Hardware Height + 1”
Universal
Mounting
Bracket
with
Ceiling
Support
Connector
Threaded
Rod
Track
Connector
or
any
Splice
Connector
1. Using your planned design (see Designing
a Plan - Pg. 3), measure then attach all the
Beam Flange Clamps or other Support
Hardware to trusses or beams.
2. Attach the Threaded Rods to the clamps.
3. Attach the Universal Mounting Brackets or
Track Connectors to the other end of the rod.
Place a nut and washer onto the rod, then
place the connector and finally another
washer and nut. Once the connector is level
with all other connectors in the assembly,
tighten the top nut to lock the hardware in
place.
4. Loosen the support
plate nut and
remove the plate
from the hardware.
= Overall Assembly Height
4
4
Support Plate
5
Support Plate Nut
Step 1
2
TIP: When inserting
Track into a Splice
Connector, lightly clamp
a pair of vice grips onto the Track
about 4” from the end. This should
narrow the Track allowing easier
insertion.
TRTSC-16
1
2. Attach an End Stop to
just one open end.
THREADED ROD
TRACK
CONNECTOR
To determine the length of the threaded rods
use the following formula:
Distance from Floor to Bottom of Truss or Beam
– Overall Assembly Height + 2”
Top of
Curtain
= Length of Threaded Rods
Next, cut all the Threaded
Rods to the proper length.
CURTAIN
1”
The same steps should be taken
if Double Track hardware is
being used.
FLOOR
Step 3
ATTACHING THREADED RODS and TRACK CONNECTORS
Step 2
MEASURING FOR MOUNTING
The total height of
the assembly
includes the height
of the curtain, the
height of the
hardware plus an
additional 1” to
keep the curtain
above the floor. A
tag on your
curtain(s) should
show the overall
dimensions.
The hardware
height is shown on
the drawings to the
right.
THREADED
ROD
2”
Overall Assembly Height
SSC-16
1. Insert the two Straight Tracks into the Connector
and tighten the screws. Repeat this process until
all pieces of track are spliced together.
Distance from Floor to Bottom of Truss or Beam
Loosen the 2 allen screws on each
Splice Connector, one and a half turns.
Length of
Thrteaded Rod
BOTTOM OF
ROOF TRUSS
BEAM FLANGE CLAMP or
OTHER SUPPORT HARDWARE
SPLICING MULTIPLE TRACKS TOGETHER
Universal
Mounting Bracket
with Ceiling Support
Connector
Threaded Rod
Track Connector
Threaded Rod
Track Splice
Connector
5 3/8”
1
2
BOTTOM OF
ROOF TRUSS
BEAM FLANGE CLAMP or
OTHER SUPPORT HARDWARE
5 3/8”
THREADED
ROD
5 3/8”
THREADED ROD
TRACK
CONNECTOR
3
1”
1”
1”
Curtain Height + Hardware Height + 1”
Universal
Mounting
Bracket
with
Ceiling
Support
Connector
Threaded
Rod
Track
Connector
or
any
Splice
Connector
1. Using your planned design (see Designing
a Plan - Pg. 3), measure then attach all the
Beam Flange Clamps or other Support
Hardware to trusses or beams.
2. Attach the Threaded Rods to the clamps.
3. Attach the Universal Mounting Brackets or
Track Connectors to the other end of the rod.
Place a nut and washer onto the rod, then
place the connector and finally another
washer and nut. Once the connector is level
with all other connectors in the assembly,
tighten the top nut to lock the hardware in
place.
4. Loosen the support
plate nut and
remove the plate
from the hardware.
= Overall Assembly Height
4
4
Support Plate
5
Support Plate Nut
End
Stop
End
Stop
IMPORTANT
Step 4
Allow the curtain(s) to reach room temperature
(above 50°F/10°C) before unfolding.
ATTACHING THE TRACKS
For convenience and ease of attaching the tracks to the Track Connectors,
already in place on the rods (Step 3), disassemble your configuration into
manageable sections.
NOTE: The installer will need an assistant to mount your curtain(s).
TRACK CONFIGURATIONS
End Stop
In Place
The hardware for the Threaded Rod Suspended Mounting Method allows for a
large number of configurations and is only restricted by the location of roof trusses
or beams. The 3 corner joints and straight run are shown here. WALL with DOORWAY OPENING
NOTE: Leave one of the
End Stops off the end of
the track assembly.
End Stop
Removed
Straight Splice Connector
Universal Mounting Bracket
Wall Mount Track Connector
Straight Track
with Ceiling Support
Connector
or
Universal Mounting Bracket
Curved
Track Connector
90° with Ceiling Support Connecto
or Threaded Rod
Track
Track Splice Connector
Universal
Mounting
Bracket
with
Ceiling
Support
Connector
Threaded Rod
Track
Connector
End
First, place the track into the
Track Connector.
End
Stop Stop
Straight Run
“T” Joint
Then, place the Support Plate
and secure with a nut.
“T” Connector
Corner Joint
Corner Connector 90°
WALL with DOORWAY OPENING
Support Plate
Straight Splice Connector
Support Plate Nut
Wall Mount Track Connector
or
Curved Corner Joint
Universal Mounting Bracket
Straight Track
Curved Track 90°
Curved Track 90°
End
Stop
with Ceiling Support Connector
End
Stop
WALL with DOORWAY OPE
Plan Views
Straight Splice Connector
Straight Track
TIP: Do not fully tighten the nut.
This will allow you to easily make
final adjustments to the hardware
assembly.
Curved Track 90°
End
Stop
DESIGNING A PLAN
Of course, firmly tighten all nuts
once the entire assembly is in
place.
Splice
Connector
The design of your curtain assembly will be determined by the position of the roof
trusses or beams. How you attach the threaded rods to the trusses is your
decision; however, we recommend using Beam Clamps. Threaded rods can easily
be attached to the clamps and quickly adjusted for height requirements.
If the track is being placed into a Splice Connector,
loosen the 2 allen screws just one and a half turns,
insert the track and tighten the allen screws.
TIP: When inserting Track into a Splice Connector,
lightly clamp a pair of vice grips onto the Track
about 4” from the end. This should narrow the
Track allowing easier insertion.
Roof Trusses
Ideally there should be 3’ or less between
clamps with suspended threaded rods,
but the span between trusses could be
slightly greater than 3’.
Beam Clamps
*
6
End
Stop
*
*
*
*
*
*
3’
*
*
*
*
*
*
Beam Clamps
*
Roof Trusses
From your design, measure and
position the Beam Clamps
*
- IMPORTANT -
Beam Clamps (unless ordered),
Threaded Rods, Nuts and Washers are
NOT included with your Curtain Kit.
3’
3
Wall Mount
Universal M
with Ceiling S
WHAT IS INCLUDED IN YOUR CURTAIN KIT
Please check the chart below to make sure you have the correct number of items.
Threaded Rod
Track Splice
Connector
Straight Track
Double
Threaded Rod
Splice Connector
Total
Length
Custom Pieces
DTRSC-16
TRTSC-16
Threaded Rod
Corner
Connector
90°
TRCC-16
Universal
Mounting
Bracket
UCMB-16
Threaded Rod
Three Way
Connector
TRTWC-D-16
Threaded Rod
Track
Connector
TRTC-16
INSERTING ROLLERS WITH HOOKS
1. Place each roller into the open end of the track. The number of rollers
must be equal to the number of grommets on the top edge of the
curtain.
1
2. Affix the second End Stop to
2
the open end of the track.
End Stop
ES-16
Step 6
Double Track
Splice
Connector
Straight Splice
Connector
HANGING THE CURTAIN
Place each curtain grommet over a roller hook and mounting is complete.
The dull side with the logo is the front and should face to the outside.
DTSC-16
Ceiling Support
Connector
Step 5
SSC-16
Curved Track 90°
Beam Flange
Clamp
CC-90-16
CSC-16
Steel Ball
Bearing
Roller with
1” Hook
SR-16-1
4 Wheel,
Steel Ball
Bearing
Roller with
1” Hook
HDSR-16-1
BFC-16
Curtain(s) with
Grommets
Nylon
Roller with
1” Hook
NR-16-1
2 Wheel
Roller with
Connector
P-SW-16
2
Number of
Curtains
7
NOTES
Managing Environments™
INDUSTRIAL CURTAINS
INSTALLATION INSTRUCTIONS
THREADED ROD
SUSPENDED MOUNTING
GETTING STARTED
Open all carton(s) containing hardware and remove all items.
Position the hardware on the floor under the opening. Next,
look in the box containing the curtain(s).
Allow the curtain(s) to reach room temperature
(above 50°F/10°C) before unfolding.
The width and height of the curtain will be listed on a tag
attached to the curtain.
Managing Environments™
Phone: 800.888.9750
Fax: 412.787.3665
5350 Campbells Run Road • Pittsburgh, PA 15205
www.tmi-pvc.com • E-Mail: [email protected]
Copyright © 2013
Catalog Number
II-ICTRM-07-13