USB-92PLL AM FM USB MP3 SD NFC 带遥控说明书.cdr
Transcription
USB-92PLL AM FM USB MP3 SD NFC 带遥控说明书.cdr
INSTRUCTION MANUAL MICRO SYSTEM AM/FM/CD/MP3/USB/SD/AUX-IN/NFC BT-207 PREPARATION FOR USE For Customer Use Enter below the Serial No. which is located On the bottom of the cabinet. Retain this Information for future reference. Mode No. Serial No. Unpacking and Setup * Carefully remove the unit from the display carton and remove all packing material from the unit itself. * Remove any descriptive labels that may be found on either the front or top cabinet of the unit. Do not remove any labels located on either the back or button cabinet of the unit. This“bolt Of lighting” indicates uninsulated material within your unit which may cause an electrical shock. TO PREVENT FIRE OR SHOCK HAZARD,DO NOT EXPOSE THIS EQUIPMENTTO RAIN OR MOISTURE. * Press the CD door OPEN Button to open the CD compartment door. There is a white card in the CD compartment which is intended to prevent the CD pickup from moving during shipment of the product, Remove this card from the CD compartment before use. Power Sources For the safety of everyone in your Using AC Power household, please do not remove Connect the AC power into Standard household wall outlet. For dual voltage version. product covering Make sure that the AC VOLTAGE SELECTOR is switched to your local voltage. The“exclamation point” calls attention to features for which you should read TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, AND FULLY INSERT. POWER SUPPLY BASIC FUNCTION Using AC Power the enclosed literature closely to prevent operating and maintenance problems. Ventilation warning: Dripping warning: The product shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,shall be placed on the product. The normal ventilation of the product shall not be impeded for intended use. 1.check if the power voltage, as shown on the type plate located on the bottom of the set, corresponds to your local ac power supply. if it does not, consult your dealer or service centre . 2.connect the power cord to the ac socket inlet and the wall outlet. the power supply is now connected and ready for use. 3.to switch off completely, unplug the power cord from the wall outlet. unplug the power cord from the wall outlet to protect your set during heavy thunderstorms. Batteries (not included) Open the battery compartment and insert eight batteries, type R-20, UM-1 or C-cells, (preferably Alkaline) with the correct polarity as indicated by the + and - symbols inside the compartment. Batteries contains chemical substances, so they should be disposed of properly Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore: Do not mix battery types: e.g. alkaline with carbon Zinc. Only use batteries of the same type for the set. When inserting new batteries, do not try to mix old batteries with new ones. Remove the batteries if the set is not be used for a long time. EN-1 EN-2 FIG 5 6 8 11 7 9 10 25 1213 IR 4 3 2 1 16 17 18 21 19 Top and front panels(See fig 1 ) 14 15 20 19 22 23 1. EQ BUTTON 2. MUTE BUTTON 3. PLAY/PAUSE BUTTON 4. STOP/USB/SD BUTTON 5. REMOTE SENSOR 6. STANDBY INDICATOR 7. POWER BUTTON 8. TIME/PROGRAM BUTTON 9. PRE- DN BUTTON 10.PRE- UP BUTTON 11.REPEAT/MO/ST BUTTON 12.FUNCTION BUTTON 13.LCD DISPLAY 24 14.RANDOM/BAND BUTTON 15.VOLUME BUTTON 16.BASS BUTTON 17. BACK/NEXT KNOB 18. AUX/PHONES/USB/SD DOOR 19.LEFT&RIGHT SPEAKER BOXES 20.FM ANTENNA 21.BATTERY DOOR 22.SPEAKER WIRE CONNECTOR(R) 23.SPEAKER WIRE CONNECTOR( L) 24. AC SOCKET 25.CD DOOR EN-3 1.EQ BUTTON -Press the button to change EQ CD/MP3/USB/ SD/AUX/RADIO's music style. -When playing the music, push down this button is in the popular-jazz-FLR-classica-rock. 2.MUTE BUTTON -Press the mute button allows CD / MP3 / USB /SD/ AUX / the RADIO to enter the mute state. 3.PLAY/PAUSE BUTTON - Start or pause MP3/CD/USB/SD/BT play. -In radio mode, press the play/pause button enter the automatic channel scan mode. 4.STOP/USB/SD BUTTON - Stop CD/MP3/USB/SD playback; erase a CD program. - Press and hold more than 1.5 sec change USB1.1/SD media(only USB). 5.REMOTE SENSOR 6.STANDBY INDICATOR 7.POWER BUTTON -Press POWER button on. 8.TIME/PROGRAM BUTTON -In standby mode, to setup the time of the unit. -program and review programmed track numbers. -In the working status, push down this button can on CD/MP3/USB/SD/RADIO for programming. 9.PRE-DN BUTTON - In the radio mode, press PRE-DN button to choose the back channel. - In the mp3 mode, Press PRE-DN button to enter the back folder. 10.PRE-UP BUTTON -In the radio mode, press PRE-UP button to choose the next channel. -In the mp3 mode, press PRE-UP button enter into the next folder. 11.REPEAT/MO/ST BUTTON - Repeat a track CD/MP3/USB/SD program. - Repeat mode : normal->repeat 1->repeat all-> repeat album ->normal. - Press MO/ST button once, to mono state. - Press MO/ST button twice, to stereo state, stereo is displayed (In FM mode). 12.FUNCTION BUTTON - Select source of sound CD/USB(SD)/BT/ AUX/RADIO. EN-4 13.LCD DISPLAY - Show the song playing time. - Show the FM dial frequency. 14.RANDOM/BAND BUTTON - In a CD/MP3 / USB/SD mode, press this button can be played at random. - The radio in the mode, press this button to select the FM STEREO, FM , AM. 15.VOLUME BUTTON - Adjust volume level. Rotate the volume button to hold the CD/MP3/ USB/SD/AUX/BT/RADIO the volume. 16.BASS BUTTON -Press the BASS button can make the CD/MP3/ USB/SD/AUX / RADIO into the BASS state. 17.BACK/NEXT KNOB BACK -To setup the time standby state BACK track selection. - Rotate and hold more than 1.5 sec BACK search intra track. - In the radio mode, Rotate BACK will enter the low end of the manual channel scan mode. NEXT -To setup the time standby state NEXT track selection. - Rotate and hold more than 1.5 sec forward search intra track. - In the radio mode, Rotate NEXT will enter the high-end manual channel scan mode. 18.AUX/PHONES/USB/SD DOOR -The built-in AUX/PHONES/USB/SD jack. 19.LEFT&RIGHT SPEAKER BOXES 20.FM ANTENNA - To improve FM reception. 21.BATTERY DOOR -To open battery compartment. 22.SPEAKER WIRE CONNECTOR (R) 23.SPEAKER WIRE CONNECTOR (L) 24.AC SOCKET - Inlet for power cord. 25.CD DOOR OPEN BUTTON - Press here to open/close the CD door. USE CLOCK Remote Control to setup the time of the unit 1.connect the ac on( The following operation must be in standby mode) . 1 4 2 3 5 8 6 7 9 12 10 11 13 16 14 15 17 19 18 1. POWER BUTTON 2. OPEN/CLOSE BUTTON 3.INTRO BUTTON 4.MUTE BUTTON 5.RANDOM BUTTON 6.P-UP BUTTON 7.REPEAT/MO/ST BUTTON 8.PROGRAM BUTTON 9.BACK BUTTON 10.FUNCTION BUTTON 11.NEXT BUTTON 12.EQ BUTTON 13.PLAY/PAUSE BUTTON 14.P-DOWN BUTTON 15.BBS BUTTON 16.STOP/BAND BUTTON 17.NUMBER KEY 18.VOL- BUTTON 19.VOL+ BUTTON 2.short according to the time button, the time will flashing on the lcd display. 3.Rotate BACK、NEXT to select the number of the time. you can setup the time format by 12h or 24h. 4.press time button to confirm. 5.then you can set the hour and the minute with the same method of steps 3-4. 6. after setup the unit time, long press the time button can setup the unit begin working time , with the same method of steps 3-4. Note: after setup the beginning time, the lcd will display the radio/cd/usb/sd/aux/blue mode, Rotate the BACK or NEXT to choose the mode, then it press time button to affirm, otherwise it playusb or aux mode first. Radio reception RANDOM BUTTON -In the player CD/MP3/USB/AUX , press the RANDOM button can be played at random. Press again to cancel. BBS BUTTON -In the player CD/MP3/USB/BT/AUX/RADIO, press the BASS button can make into the bass state. Press again to cancel. EQ BUTTON -In the player CD/MP3/USB/BT/AUX/RADIO, press the EQ button to change music style. -When playing the music, press this button is in the classica-rock-popular-jazz-FLR. MUTE BUTTON -In the player CD/MP3/USB/BT/AUX/ RADIO, press the MUTE button to enter the mute state. Press again to restore volume. INTRO BUTTON -In the player CD/MP3/USB,press the INTRO button into 10 seconds browsing repertoire state, press again cancel browse. * Please pull out the plastic paper from the battery door before use the remote control. * When the remote control operation becomes unstable or the distance from which the remote control works is shorter. replace the batteries with new ones. * Using the remote control unit To use the remote unit, point at the REMOTE SENSOR and press the buttons gently and firmly. Remote control operation is possible within approximate 18ft (6m). However, since the remote control range is less when the unit is used at an angle, use directly in front of the REMOTE SENSOR, for maximum distance. Do not expose the REMOTE SENSOR to strong light (direct sunlight or artificial lighting) and make sure that there are no obstacles between the REMOTE SENSOR and the remote control unit. ENEN-5 1. Press FUNCTION button select RADIO mode . 2 .Press BAND to select the desired wave band: FM STEREO, AM, FM, FM ST. 3.Tune to required station by Rotate BACK/ NEXT or press PRE-DN /PRE-UP. Manual Tuning: Rotate BACK or NEXT and then release within 1 sec. Auto Tuning: Press the play/pause button enter the automatic channel scan mode, and to be put automatically sets. Preset Channel:(FM 30 Preset memories, AM 10 preset memories ) (1) Rotate BACK/ NEXT Select desired station. (2) Press PROGRAM button once , The MEMORY number indicator begins steady in the display. (3) Press PRESET-UP OR PRESET- DN buttons to select the desired number. (4) Press PROGRAM button to save that station. (5) Repeat steps (1) to (4) procedures for other stations. 4.After end of program. press PRE-UP or PRE-DN to start play the frequency that you selected or Press number key on the remote control. 5. Rotate [VOL-]or [VOL +] to adjust the volume. 6.Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting. 7.Turn off the radio by press FUNCTION button select other mode or press power button to off the unit. 8.Switch on again after shut down, the memory frequency still exists. MONO/STEREO -Press MO/ST button once, to mono state. -Press MO/ST button twice, to stereo state, stereo is displayed. EN-6 PROGRAM METHOD CD/MP3 PLAYER (1)Press the [PROGRAM] key at STOP mode, system will go to PROGRAM mode. -The PRG icon and P01 will blink at 2Hz. This prompts the user to enter the first songs in the program PLAY list. CD/MP3 Player Playing a USB/SD Playing a CD/MP3 (2)The user can select the desire tracks by using [NEXT], [BACK] keys. Once these keys are pressed, the Display will show the selected track. (3)After select the desired track, press [PROGRAM] key again and it will be stored in the memory. Mp3 Maximum 99 and CD Maximum 20 tracks can be programmed when Repeat steps (2) to (3) procedures. (4)If press the [STOP] key during the program mode, then the selected TRACKs will be stored in the memory and return to STOP mode (Continuous Play mode) (5)If press the [PLAY] key during the program mode, it will start the program PLAY mode. PLAY start from P01 Track Erasing a program You can erase the content of the memory by: - While playing, press STOP button twice. - Opening the CD door - Select the other mode. USE AUX To listen music with a mp3、discman、walkman . 1.Connect to the AUX . 2.press function selector to AUX, the sound source of the mp3 or discman or walkman will output from the unit. -Rotate the volume control to adjust the volume. -The unit can't control the player. USB/SD Audio functions This CD-player can play Audio Discs,MP3 CD-R. 1)press function button or stop/usb/sd button to Do not try to play CD-ROM,CDi,VCD,DVD or choose the usb or sd state. computer CD. 2) PLAY/PAUSE 1.Press function button to CD state. 2.to open the cd door, press cd open button. 3) NEXT, BACK Skip search 3.insert a mp3/cd or cd-r、with the printed side 4) Program Track(MP3 99 Track, CD 20 Track ) facing up and press cd door gently to close. 5) REPEAT MODE : normal->repeat 1->repeat all-> 4.press play/pause on the set to start playback. repeat album ->normal 5.Press the pause button to pause play, press 6) Maximum Folder : 99 Folders the play button back playing. 7) Maximum File : 999 Files 6.to stop cd playback , press stop. note: cd/mp3 play will also stop when: -Press and hold the [STOP] key more than 1.5sec -you open the cd compartment; at USB mode , system will change to SD mode. -you select radio sound source; Then “SD“ will be display. At this moment, -the cd/mp3 has reached to the end. system will read the SD . selecting a different track. If a device is successfully read, then the during playback you can use back or next to select a particular track. correspond device is ready to play a file. if you have selected a track number in the - If a device fails to be read, then “NO” will stop or pause position, press play to start be appeared on the Display to indicate that there playback. is no device . Rotate next once briefly for the next track, *Notice : If no device is attached or the player or press repeatedly until the desired track fails to read the device when a user switch over number appears in the display. Rotate back once briefly to return to the USB to SD with pressing [STOP] key, beginning of a current track. then “NO” is displayed and the system moves Rotate back more than once briefly for a into the STOP mode. previous track. -When the unit has not the disc, inserting the finding a passage within a track usb/sd card will automatically real usb/sd card, 1.Rotate and hold down back or next. the cd is played at high speed. it read the USB first while having the USB. 2.when you recognize the passage you want -The unit don’t support the HDD all and the portion release back or next. usb with mp3 player. normal playback resumes. Note: at the mode of CD/MP3 / USB/SD,the lcd will different play modes:repeat display the number of song or the song playing time. repeat-play the current track continuously. repeat all-plays the entire cd continuously. playing tracks in random order after press the random button, the tracks will be played in random order. EN-7 EN-8 USE NFC Press FUNCTION button select to bluetooth mode. Search bluetooth equipment ”BT-207" math connection, such as need to enter pass word for “0000". 1. Press PLAY/PAUSE button to play or pause playback. 2. Rotate [VOL-]or [VOL +] to adjust the volume size. 3. Rotate BACK or NEXT to select tracks. NOTE: Bluetooth effective receiving distance of about 10M,different bluetooth devices may be slightly different operation, please read carefully before operation you use the bluetooth device (IPHONE, IPAD,MOBILE PHONE, ETC.) Instructions. NFC(Near Field Communication) function for Phone or Tablet First, press FUNCTION button to select bluetooth mode. If your phone(tablet) support NFC, first turn on bluetooth NFC working mode, and confirm setting “Allow data exchange when it torches another device”. Move your phone(tablet) to near this unit(USB-92) no more than 10CM, or lightly touch the NFC sensor area. When hear a sound “Di Da” from the USB-92 that means connect success. Then you can play the music through the USB-92 from your phone(tablet). NFC OPEN/CLOSE EN-9 EN-10 TECHNICAL SPECIFICATIONS GENERAL Power Requirement ............................................................AC 120/220V~50/60Hz Power consumption .............................................................AC 20 Watts Dimensions......................................................Appro.434 mm(L)x214 mm(W) x228 mm(H) Operation temperature.........................................................+5°C - +35°C RECEIVER SECTION Receiving Bands...................................................................AM/FM Tuning Range..........................................................AM: 530-1710kHz CD/MP3/ USB/SD playback does not work CD/MP3/ USB/SD badly scratched/dirty Replace/clean CD/MP3/USB/ SD (see maintenance) FM: 88-108MHz AUDIO SECTION Power output .........................................................................Maximum 3 Watt x2 Headphone Impedance ............................................................4 ~ 32 Ohms ACCESSORIES The CD/MP3 skips tracks CD/MP3 damaged or dirty Replace or clean CD/MP3 Instruction Booklet.....................................................................1 Remote control..........................................................................1 Ac line cord...............................................................................1 No CD/MP3 inserted Insert a CD,MP3, CD-R. - CD- R、is blank or the disc is not finalized Use a finalized CD- R. EN-11 EN-12