tiverton offset umbrella

tiverton offset umbrella
style # YJAF-013T
dpci # 009050540
>>assembly instructions
TM
Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.
IMPORTANT WARNING:
Unpack the box on a clean level surface and make sure all parts have been included.
To replace missing or damaged parts please call 1-866-905-4107,Monday through Friday, 8:30 AM to 5:00 PM Pacific Standard Time
/ 11:30 AM to 8:00 PM Eastern Standard Time or visit our website at www.yotrioint.com.
DO NOT RETURN THIS PRODUCT TO THE RETAILER.
Ideally, this umbrella should be set up in its desired location to avoid moving it after assembly.
Expensive flooring should be protected from scratching.
To replace missing or damaged parts please call 1-866-905-4107,Monday through Friday, 8:30 AM to 5:00 PM Pacific Standard Time
/ 11:30 AM to 8:00 PM Eastern Standard Time or visit our website at www.yotrioint.com.
ATTENTION:
This Offset Umbrella is not intended for use during any kind of inclement weather and the manufacturer is not,
and can not be, held responsible for any damage caused as a result of such weather. Weather-related damage,
or damage as a result of the umbrella not being stored properly when not in use, is not the responsibility
of the manufacturer.
The umbrella is designed as a shade structure only and must be taken down and stored in a clean, dry and
safe area when not in use.
2
WARRANTY:
This Offset Umbrella come with a one year limited warranty against original manufacture defects. If you experience
trouble with your new umbrella, please call the customer service number below or visit us at www.yotrioint.com
Yotrio Corporation
708 Nogales Street
City of Industry, CA 91748
Toll Free at: 1-866-905-4107 (8:30 AM - 5:00 PM Pacific Standard Time/11:30 AM to 8:00 PM Eastern Standard Time.
Or visit our website at www.yotrioint.com)
Code: Yotrio 2010
before you begin
1. Check for damage or missing parts. Call 1-866-905-4107 to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
3
table of contents
introduction
hardware
parts list
assembly
4
QUESTIONS?
2-3
5
6
7-22
Just call 1-866-905-4107 parts and service. For faster service, have the style number and DPCI number ready when calling.
hardware
(Part D)×4
M8×20mm bolts
(Part E)×4
Ø8 flat washer
(Part J)×1
sheet metal
(Part K)×1
screw - in knob
(Part M)×1
Wrench
5
ITEM
DESCRIPTION
QUANTITY
A
lower bracket
1
B
upper bracket
1
C
base tube
1
F
plastic base top cover
1
G
plastic base cover
2
H
plastic base
4
I
tube rim
1
L
sunshade
1
L
I
G
H
J
F
C
G
K
H
H
H
B
A
6
step 01:
B
1.Place upper bracket (B) onto lower bracket (A) as shown.
A
7
step 02:
C
D
E
(Part D)×4
M8×20mm bolts
(Part E)×4
Ø8 flat washer
1.Line up the bolt holes on the base tube (C) with the corresponding bolt
holes on the two brackets. Screw the bolts (D) on with washers (E).
8
step 03:
H
1.Install the plastic base (H) on the brackets. Embed the chocks of the
left part (H) into the rabbets of the right part (H).
H
9
step 04:
1.Fill entire base with dry sand and make level to the top of
the triangular sections. Add water to the sand for additional
weight. A minimum of 125 lbs. of sand is required for the
first level.
10
step 05:
H
1.Repeat the procedure of step 3 to install the remaining
plastic base (H).
H
11
step 06:
1.Fill entire base with dry sand and make level to the top of
the triangular sections. Add water to the sand for additional
weight. A minimum of 125 lbs. of sand is required for the
second level. You should now have a required minimum of
250 lbs of dry sand in your plastic base (H).
12
step 07:
G
H
1. Cover the plastic base (H) with the plastic covers (G).
Press down firmly to snap plastic covers (G) into place.
13
step 08:
C
F
G
1. Thread plastic base top cover (F) through base tube (C). Line up
the posts on the underside of the plastic base top cover (F) to the
holes on the plastic base cover (G). Gently push down.
14
step 09:
I
J
C
K
(Part K)×1
screw - in knob
1.Put sheet metal (J) and tube rim (I) on top of base tube (C) then
screw the knob (K) on. The plastic base now is finished.
Note: This umbrella base is designed to support an umbrella no
larger than 12 feet in diameter.
15
step 10 :
L
1.Insert the stem of the sunshade (L) into the base tube (C),
turn the screw-in knob (K) until tight.
K
16
C
step 11:
1.Place hand into umbrella crank handle (as shown),squeeze the
trigger to unlock,slide umbrella crank handle upward until it is fully
extended and stops.
C
17
step 12:
1.
2.
1. Remove the "Z" shape crank ( M ) and insert it into the hole in stem,
turn the "Z" shape crank (M) clockwise to fully unfold the umbrella.
18
step 13:
1.
2.
1.Put out the “Z” shape crank (M) and attach it into the original place,
than the umbrella canopy can be adjusted to different positions by
moving the umbrella crank handle upward or downward (as shown).
19
step 14 :
1.Before using your 360 degree turning function, please check to make sure
the 4 screws are tightened and secured.
NOTE: Over time, these screws can become loose. If they become loose,
you need to tighten the 4 screws with the allen wrench that has been provided.
20
step 15 :
1.
2.
Lock to secure,
Unlock to move.
1.The umbrella is able to turn up to 360 degrees by pressing down the
locking mechanism (as shown). To fix the umbrella at a desired position,
simply release the lock.
NOTE: Periodically, you must use a lubricant on the locking collar to prevent
the loss of function on the locking mechanism.
Should you experience this problem, please feel free to contact our
Customer Service department at 1-866-905-4107 for further direction.
21
step 16:
CAUTION: It is normal for the offset umbrella top to
sway right, left, backwards, and forward. Always close
umbrellas in their stands when not in use.
Umbrellas must always be closed and properly secured
in windy conditions and or stored in a dry shelter during
inclement weather to protect
umbrellas and to protect persons from potential injury
due to umbrellas toppling or moving in such conditions.
22
step 17:
You are now ready to enjoy your new offset umbrella.
23
step 18:
STORAGE: Proper storage of umbrella when not in use. See image above.
During extended periods of non-usage, off season, or in inclement weather
(wind, rain, snow, hail, sleet), freezing conditions and extreme heat, the offset
umbrella and base must be separated and stored in a dry,sheltered place to
prolong life and to avoid damage to the offset umbrella.
24
TM
2010 Target. The Bullseye Design is a trademark of Target Brands Inc. All rights reserved.