Instructions for use, installation, and connection Gas Built in Hob

Instructions for use, installation,
and connection
Gas Built in Hob
RB-3311S-GBS
RB-3312S-GBS
RB-3311D-GBS
RB-3311M-GBS
RB-3311N-GBS
RB-6313S-GBST
RB-6323S-GBST
RB-6314S-GBS
RB-6313D-GBST
RB-6313M-GBST
RB-7312S-GBS
RB-7313S-GBST
RB-7323S-GBST
RB-7314S-GBS
RB-7315S-GBS
RB-7313D-GBST
RB-7312M-GBS
RB-7313M-GBST
RB-7312N-GBS
RB-9312S-GBS
RB-9313S-GBST
RB-9314S-GBS
RB-9315S-GBS
RB-9312D-GBS
RB-9213D-GBST
RB-9314D-GBS
RB-9315D-GBS
RB-9312M-GBS
RB-9313M-GBST
RB-9312N-GBS
RB-9313N-GBSU
1
Contents
1. Important Warnings......................................................... 3
2. Safety Instructions........................................................... 4
3. Line up............................................................................. 6
4. Components and Parts name......................................... 7
5. Installation....................................................................... 8
6. Operating Instructions................................................... 12
7. Maintenance.................................................................. 13
8. Trouble Shootings......................................................... 17
9. Technical Specifications................................................ 18
Thank-you very much for purchasing Rinnai Gas Built in Hob.
More than 90 years of history of introducing high qualified Japandesigned appliances throughout the world.
Every time you use Rinnai appliances, Rinnai believes you can feel
comfort by its safety and quality.
In order to maximize the performance and to maintain your Rinnai builtin hob in the best condition, please follow the instruction carefully.
Please visit www.rinnai.com for further inquires
2
1. Important Warnings
Before installing and using of Rinnai
appliances, carefully read and follow the
supplied instructions. The manufacturer
is not responsible for any damages
caused by incorrect installation and use.
This instruction shall always be kept with
the appliance for future reference and
pass them on to possible new owners of
the appliance.
1.1 General
• T
he appliance and its accessible parts
become hot during use.
• Unattended cooking on a hob with fat
or oil can be dangerous and may result
in fire. Never try to extinguish a fire
with water, but switch off the appliance
and then cover flame e.g. with a lid or
a fire blanket.
• The appliance is not intended to be
operated by means of an external timer
or separate remote control system.
• Do not store items on the cooking
surfaces.
• Do not use a steam cleaner to clean
the appliance.
1.2 Children and vulnerable people
WARNING!
R
isk of suffocation, injury or
permanent disability.
• T
his appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack
of experience and knowledge if they
are supervised by an adult or a person
who is responsible for their safety.
• Never let children play with the
appliance.
• Keep all packaging material out of the
reach from children.
• Keep children and pets away from the
appliance when it operates or when it
cools down.
• Never let children clean and
maintenance without supervision.
3
2. Safety Instructions
2.1 Installation
WARNING!
Only a qualified person must install
this appliance.
• Remove all the packaging.
• Never install or use a damaged
appliance.
• The minimum distance shall be kept
from the other appliances and units as
instructed.
• Always wear safety gloves and be
careful when you move the appliances.
• Protect the bottom of the appliance
from any steam and moisture.
• Preventing from the appliance to fall,
never install the appliance adjacent to
a door or under a window.
• Sufficient spaces are needs for air
circulation when the appliance is
installed above drawers.
Gas connection
• All gas connections must be made by
a qualified person.
• Confirm sufficient air circulation around
the appliance.
• Always connect the appliance
according to the latest installation
regulations.
2.2 Use
WARNING!
Risk of burns.
• CAUTION: The use of a gas cooking
appliance results in the production
of heat, moisture and products of
combustion in the room in which it
is installed. Ensure that the kitchen
is well ventilated especially when
the appliance is in use : keep natural
ventilation holes open or install
a mechanical ventilation device
(mechanical extractor hood).
4
• CAUTION : This appliances is for
cooking purposes only. It must not be
used for other purposes, for example
room heating.
• This appliance is intended for use in
household.
• Never change the specification of this
appliance.
• Do not let the appliance stay
unattended during operation.
• Ensure the cooking zone to “off” after
cooking.
WARNING!
Risk of fire or explosion.
• Fats and oil when heated can release
flammable vapors. Keep flames or
heated objects away from fats and oils
when you cook with them.
• The vapors of hot oil releases may
cause spontaneous combustion.
• Used oil may cause fire at a lower
temperature.
• Never place flammable products or
items near or on the appliance.
WARNING!
Risk of damage to the appliance.
• Do not place and keep hot cookware
on the control panel.
• Do not ignite the flames with empty
cookware or without cookware.
• Be careful not to let objects or
cookware fall on the appliance. The
glass top plate can be damaged.
• Do not place aluminum foil on the
appliance.
• Never use unstable cookware with the
incorrect shape and diameter larger
than the dimensions of the burners.
• Make sure the flame does not go out
when you quickly turn the knob from
the maximum to the minimum position.
• Make sure cookware is centrally
positioned on the pan supports and do
not stick out over edges of the cooking
surface.
• Only apply the accessories supplied by
manufacturer.
• Never install a flame diffuser on the
burner.
2.3 Care and Cleaning
WARNING!
Risk of damage to the appliance.
• Clean regularly the appliance to prevent
the deterioration of the surface material.
• Do not use steam to clean the
appliance.
• Never use the dishwasher to clean the
burners in the dishwasher.
• Clean the appliance with a moist soft
cloth, and only use neutral detergents.
Never use abrasive products, abrasive
cleaning pads, solvents or metal
objects.
• CAUTION: In case of hotplate glass
breakage:
-Shut immediately off all burners and
any electrical heating element and
isolate the appliance from the power
supply.
-Do not touch the appliance surface,
-Do not use the appliance
2.4 Caution for the tempered glass
• Never use oversized
cooking utensils or
overload the cooking
appliances.
• Do not remove the pan
support and enclose the
burner with a wok stand as
this will concentrate and
deflect the heat onto the
gas hob.
• Do not place the builtin hob pan over the pan
support side as it can
cause tumbling.
• Use only a wok support
supplied or recommended
by the manufacture of the
appliance.
• Do not place anything, e.g.,
flame tamer, asbestos mat
between pan and support
as serious damage to
appliance may result.
2.5 Disposal
WARNING!
Risk of injury or suffocation.
• Please contact your near municipal
authority for detailed information on the
disposal of appliance.
5
3. Line up
30cm Models
Top Plate Dimension ; 310 mm × 520 mm
Cut-Out Hole Dimension ; 268 mm × 490 mm × R0 mm ~ R50 mm
RB-3311N-GBS
RB-3311M-GBS
RB-3311D-GBS
RB-3311S-GBS
RB-3312S-GBS
Inner Flame
Mega
Double Simmer
Simmer
Simmer
60cm Models
Top Plate Dimension ; 620 mm × 520 mm
Cut-Out Hole Dimension ; 560 mm × 480 mm × R0 mm ~ R50 mm
RB-6313M-GBST RB-6313D-GBST RB-6313S-GBST RB-6323S-GBST
Mega
Double Simmer
Simmer
RB-6314S-GBS
Simmer
Simmer
75cm Models
Top Plate Dimension ; 770 mm × 520 mm
Cut-Out Hole Dimension ; 725 mm × 480 mm × R0 mm ~ R50 mm
RB-7312N-GBS
Inner Flame
RB-7312M-GBS RB-7313M-GBST RB-7313D-GBST
Mega
RB-7313S-GBST RB-7323S-GBST
Simmer
Mega
Double Simmer
RB-7314S-GBS
RB-7315S-GBS
Simmer
Simmer
Simmer
RB-7312S-GBS
Simmer
90cm Models
Top Plate Dimension ; 880 mm × 520 mm
Cut-Out Hole Dimension ; 830 mm × 470 mm × R0 mm ~ R100 mm
6
RB-9312N-GBS
RB-9313N-GBSU
RB-9312M-GBS
RB-9313M-GBST
Inner Flame
Inner Flame
Mega
Mega
RB-9312D-GBS
RB-9313D-GBST
RB-9314D-GBS
RB-9315D-GBS
Double Simmer
Double Simmer
Double Simmer
Double Simmer
RB-9312S-GBS
RB-9313S-GBST
RB-9314S-GBS
RB-9315S-GBS
Simmer
Simmer
Simmer
Simmer
4. Components and Parts name
Rinnai Original Burner Series
Inner Flame Series
Mega Series
Double Simmer Series
Simmer Series
Parts Names
Inner Flame Series
Pan Support H
Drip Pan
Burner Cover H
Mega Series
Pan Support S
Pan Support
Burner Cover S
Drip Pan S
Burner Head S
Burner Head H
Burner cover
Drip Pan
Drip Pan Seal Packing
Burner S
Top Burner HS
Knob
Casing
Tempered Glass
Top Plate
Double Simmer Series
Pan Support H
Simmer
Burner Head
Burner Head H
Pan Support
Center
Simmer Series
Pan Support S
Pan Support H
Burner Head S Small Burner
Burner Body S Cap
Burner Body S
Simmer Burner
Cap
Burner Cap H
Burner Body H
Burner Cover H
Burner Cover S
Burner Body H
Knob
Casing
Tempered Glass
Top Plate
Knob
Casing
Tempered Glass
Top Plate
Knob
Casing
Tempered Glass
Top Plate
7
5. Installation
Kitchen worktop cut-out dimensions
Model
30 cm
RB-3311S-GBS
RB-3312S-GBS
RB-3311D-GBS
RB-3311M-GBS
RB-3311N-GBS
Cut out hole dimension (mm)
268 x 490
R0~R50
R0~R50
0
49
26
8
65
60 cm
RB-6313S-GBST
RB-6323S-GBST
RB-6314S-GBS
RB-6313D-GBST
RB-6313M-GBST
560 x 480
R0~R50
R0~R50
56
0
0
48
75 cm
90 cm
8
725 x 480
R0~R50
RB-9312S-GBS
RB-9313S-GBST
RB-9314S-GBS
RB-9315S-GBS
RB-9312D-GBS
RB-9213D-GBST
RB-9314D-GBS
RB-9315D-GBS
RB-9312M-GBS
RB-9313M-GBST
RB-9312N-GBS
RB-9313N-GBSU
830 x 470
R0~R100
N)
MI
0(
60
65
RB-7312S-GBS
RB-7313S-GBST
RB-7323S-GBST
RB-7314S-GBS
RB-7315S-GBS
RB-7313D-GBST
RB-7312M-GBS
RB-7313M-GBST
RB-7312N-GBS
N)
MI
0(
60
R0~R50
72
5
0
48
N)
MI
0(
60
65
R0~R100
83
0
0
47
65
N)
MI
0(
60
WARNING!
*Install the built-in hob in a well ventilated room and keep it away from any combustible
or flammable objects such as paper or oil.
*Place the built-in hob on a stable and level surface.
*If the built-in hob is to be installed close to combustible objects (such as wooden walls,
wooden shelves), it should be installed at least 15 cm from the side walls. Even if the
combustible material is protected by stainless steel sheet, a clearance of 15 cm must be
maintained too. If the surrounding material is fireproof, 15 cm clearance is not required.
The clearance between the appliance and above combustible shelves or the ceiling
must be at least 100 cm.
*(For Mega burner series only) If the oven is installed underneath of hob, it is mandatory
to install the separator in between. The separator must be made out of incombustible
material (eg. metal or plywood).
0
15
in)
(m
1000 (min)
15
0(
mi
n)
15
0(
mi
n)
●If the separator is placed underneath of the hob, its distance shall be recommended to be kept more
than 150mm away from the surface of kitchen worktop. Please refer to below diagram.
150
● Adjust screw position as bench cut out size.
● Confirm that four screws are secured firmly into the casing.
Table
Casing
Screw
9
● Set the battery properly as instructed.
Model
Ignition
Battery Size
RB-3311S-GBS
C (1.5V × 1)
RB-3312S-GBS
C (1.5V × 1)
Battery holder location
Front
+
30 cm
RB-3311D-GBS
C (1.5V × 1)
RB-3311M-GBS
C (1.5V × 1)
RB-3311N-GBS
C (1.5V × 1)
RB-6313S-GBST
C (1.5V × 1)
RB-6323S-GBST
C (1.5V × 1)
-
+
-
Front
C (1.5V × 1)
Front
+
60 cm
RB-6314S-GBS
D (1.5V × 2)
RB-6313D-GBST
C (1.5V × 1)
RB-6313M-GBST
C (1.5V × 1)
RB-7312S-GBS
C (1.5V × 1)
RB-7313S-GBST
C (1.5V × 1)
RB-7323S-GBST
C (1.5V × 1)
RB-7314S-GBS
D (1.5V × 2)
RB-7315S-GBS
D (1.5V × 2)
RB-7313D-GBST
C (1.5V × 1)
RB-7312M-GBS
C (1.5V × 1)
RB-7313M-GBST
C (1.5V × 1)
RB-7312N-GBS
C (1.5V × 1)
RB-9312S-GBS
C (1.5V × 1)
RB-9313S-GBST
C (1.5V × 1)
RB-9314S-GBS
D (1.5V × 2)
RB-9315S-GBS
D (1.5V × 2)
RB-9312D-GBS
C (1.5V × 1)
RB-9213D-GBST
C (1.5V × 1)
-
+
-
+
-
+
-
C (1.5V × 1)
Front
90 cm
-
D (1.5V × 2)
RB-9315D-GBS
D (1.5V × 2)
+
+
-
10
+
-
C (1.5V × 1)
C (1.5V × 1)
RB-9313M-GBST
C (1.5V × 1)
RB-9312N-GBS
C (1.5V × 1)
RB-9313N-GBSU
C (1.5V × 1)
-
+ D
(1.5V × 2)
Front
Front
+
+
-
+
+
-
+
RB-9312M-GBS
D (1.5V × 2)
+
-
-
RB-9314D-GBS
+
Front
+
75 cm
+
-C
(1.5V × 1)
-
-D
+
(1.5V × 2)
● Set the pan support properly as instructed.
* Set pan support to top plate.
Inner Flame Series H, S
Mega Series
H Burner
S Burner
Double Simmer Series H, S
H Burner
S Burner
H Burner
S Burner
Simmer Series H, S
Installation of Gas Hose
● Certified rubber hose for built-in hob must be applied.
●The rubber hose must no be bent during installation and must be at appropriate length (less than 2 m).
●During installation, make sure that the rubber hose must not touch the body
and bottom part of the built-in hob.
●Set the securing ring over the rubber hose and connect to the gas inlet rear
side of the built-in hob till the red marked line. Secure the position of rubber
hose by tightening securing ring.
●The installation of gas hose must be performed by a qualified installer according
to the relevant standards (For LP Gas).
Red marked
line
Gas inlet
Rubber hose
Securing
ring
Important
Once installation is complete, check the perfect seal of every pipe fitting, using a soapy
solution, never a flame.
11
6. Operating Instructions
Ignition
1. Press the control knob for about 3 mm and turn to the left (counter clock-wise) to the “● ● ● ”(MAX)
position.
2 In the event of the burner flames being accidentally extinguished, turn off the burner control and do
not attempt to re-ignite the burner for at least 1 min. If the burner has not lit up after 15 seconds,
stop operating the built-in hob and open the compartment door and/or wait for at least 1 minute
before attempting to ignite the burner again.
3. The flame can be controlled between “●● ● ”(MAX)
and “ ● ”(MIN) position, please adjust the flame
slowly.
4. Do not clean the top of the sensor with a hard
brush, as it may damage the sensor.
Max Position
Min Position
Flame Extinguishing
1. After the usage, turn the control knob right (clock-wise) to the original “●” position and the flame will
be extinguished.
2. After extinguishing of the flame, do not touch the conductive parts of the built-in hob as they may
remain at high temperature.
3.There might be a slight hissing sounds after the extinguishing of the flame.
4. If the built-in hob is not in use, turn off the main gas supply in order to avoid gas leakage or
unnecessary accidents.
How to Handle Safety Device
1.If the flame is extinguish during operation, the flame failure safety device will automatically cut off the
gas within second.
If you notice that the flame has been extinguished, please turn the knob to “●” position and do not
attempt re-ignite the burner at least 1 minute.
12
7. Maintenance
How to Change Battery
1. If the battery ran out, open the cabinet door and change it correctly. The location of the battery is
described in Page 10.
• Battery box is located at bottom of built-in hob.
Open the cabinet door and change the battery.
* Set battery correctly with care. + -
How to set Drip Pan
Inner Flame Series
* Set Burner Cover properly as instructed.
* Set drip pan into burner correctly, without gap.
Burner Cover
×
✓
Slot
Gap
Pin
Drip Pan
Mega Series
* Set the drip pan properly as instructed.
Slot
Drip Pan
✓
×
Pin
Gap
13
*Set Burner Head H on Top Burner Body HS properly. The Pin of Burner Head H shall be located
onto the Slot on Top Burner Body HS.
Set Burner Head S on the Top Burner Body HS properly.
Pin
Pin
Burner Head H
Burner Head S
Top Burner Body HS
Slot
Slot
×
✓
×
Gap
Gap
Double Simmer Series H, S
* Install Burner Body H to Burner Base H properly. The Slot on Burner Body H shall be properly
located onto the Pin of Burner Base H.
* Install Burner Head H to Burner Body H properly. The Slot on Burner Body H shall be properly
located onto the Pin of Burner Head H.
* Install Simmer Burner Head to Burner Body H properly. The Slot on Burner Body H shall be properly
located onto the Pin of Simmer Burner Head.
Burner Body H
Simmer Burner Head
Burner
Head H
Slot
Pin
Pin
Pin
Burner Body H
Burner Base H
14
Slot
Slot
* Install Burner Body S to Burner Base S properly. The Slot on Burner Base S shall be properly located
onto the Guide Pin of Burner Body S.
* Set Burner Head S on Burner Body S.
Burner Body S
Guide Pin
Burner Head S
Pin
Slot
Slot
Burner Base S
* Set Burner Head on Burner Body H properly without gap as below illustration.
×
✓
×
Gap
Gap
Simmer Burner
Head
Burner Body H
×
Gap
15
Simmer Series H, S
* Set burner Body H on burner base H. Be careful to align guide pin of burner body with slot of burner
base.
* Install Burner Cap H and Simmer Burner Cap properly onto Burner Body H.
Simmer Burner Cap
Guide Pin
Burner Cap H
Burner Body H
Slot
Burner Base H
* Install Burner Body S to Burner Base S properly.
The Slot on Burner Base S shall be properly located onto the Guide Pin of Burner Body S.
* Set Small Burner Cap on Burner Body S.
Burner Body S
Guide Pin
Small Burner Cap
Burner Body S
Slot
Burner Base S
* Set burner cap on burner body properly without gap as below illustration.
Burner Cap
✓
×
×
Gap
Burner Body
×
Gap
16
Gap
8. Trouble Shootings
FAULT
CAUSE
REMEDY
Spark electrode is wet, especially in
high humidity season.
Dry the electrode with clean tissue
or dry cloth.
Incorrect turning of gas control
knob.
Push and turn the gas control knob
anti-clockwise until a ‘click’ sound
is heard. Hold for a few seconds
until flame is ignited.
3. No main flame.
Gas regulator has been turned off.
Open gas regulator completely.
4. Yellow flame.
Accumulated grease and dirt on the
burner.
Wash the burner in warm water
with detergent. Leave it to dry, then
place it back in the correct position.
5. Unstable flame.
Incorrect location of burner head.
Refit burner head into burner ring.
1. No Ignition
2. Flame cannot
be held.
17
9. Technical Specifications
30 cm
60 cm
75 cm
90 cm
18
Cut out
Ignition
Respective gas consumption (kW)
Net
Overall
Weight
Dimension
RB-3311S-GBS
6.8
310 x 520 x 130
3.7
RB-3312S-GBS
8.1
310 x 520 x 130
RB-3311D-GBS
7.8
310 x 520 x 136
RB-3311M-GBS
8.2
RB-3311N-GBS
Model
hole size
Battery Size High Medium
small
all
—
—
3.7
3.2
—
1.6
4.7
4.2
—
—
4.2
310 x 520 x 127
5.0
—
—
5.0
7.1
310 x 520 x 112
3.5
—
—
3.5
RB-6313S-GBST
14.2
620 x 520 x 130
C (1.5V × 1)
3.7
—
1.6 x 2
6.8
RB-6323S-GBST
14.6
620 x 520 x 130
C (1.5V × 1)
3.7
3.2
1.6
8.2
RB-6314S-GBS
16.0
620 x 520 x 130
—
1.6 x 2
9.3
RB-6313D-GBST
15.4
560 x 480
D (1.5V × 2) 3.2 x 2
R0~R50
620 x 520 x 136
C (1.5V × 1) 4.2
—
1.5 x 2
7.2
RB-6313M-GBST
15.8
620 x 520 x 127
C (1.5V × 1)
—
1.5 x 2
8.0
RB-7312S-GBS
16.4
770 x 520 x 130
C (1.5V × 1) 3.7 x 2
—
—
7.2
RB-7313S-GBST
17.2
770 x 520 x 130
C (1.5V × 1)
3.7
—
1.6 x 2
6.8
RB-7323S-GBST
17.4
770 x 520 x 130
C (1.5V × 1)
3.7
3.4
1.6
8.5
RB-7314S-GBS
18.8
770 x 520 x 130
D (1.5V × 2) 3.4 x 2
—
1.6 x 2
9.7
RB-7315S-GBS
20.0
770 x 520 x 130
—
1.6 x 3
11.0
RB-7313D-GBST
18.0
725 x 480
D (1.5V × 2) 3.4 x 2
R0~R50
770 x 520 x 136
C (1.5V × 1) 4.2
—
1.5 x 2
7.2
RB-7312M-GBS
18.9
770 x 520 x 127
C (1.5V × 1) 5.0 x 2
—
—
9.9
RB-7313M-GBST
18.6
770 x 520 x 127
C (1.5V × 1)
—
1.5 x 2
8.0
RB-7312N-GBS
16.9
770 x 520 x 112
C (1.5V × 1) 3.5 x 2
—
—
6.8
RB-9312S-GBS
17.3
880 x 520 x 130
C (1.5V × 1) 3.7 x 2
—
—
7.2
RB-9313S-GBST
17.7
880 x 520 x 130
C (1.5V × 1) 3.7 x 2
—
1.6
8.7
RB-9314S-GBS
19.8
880 x 520 x 130
D (1.5V × 2) 3.7 x 2
—
1.6 x 2
10.3
RB-9315S-GBS
21.0
880 x 520 x 130
D (1.5V × 2) 3.7 x 2
—
1.6 x 3
11.5
RB-9312D-GBS
18.8
880 x 520 x 136
C (1.5V × 1) 4.2 x 2
—
—
7.9
RB-9213D-GBST
20.1
—
1.5
9.4
RB-9314D-GBS
21.5
880 x 520 x 136 830 x 470 C (1.5V × 1) 4.2 x 2
880 x 520 x 136 R0~R100 D (1.5V × 2) 4.2 x 2
—
1.5 x 2
10.7
RB-9315D-GBS
22.8
880 x 520 x 136
D (1.5V × 2) 4.2 x 2
—
1.5 x 3
12.2
RB-9312M-GBS
19.6
880 x 520 x 127
C (1.5V × 1) 5.0 x 2
—
—
9.9
RB-9313M-GBST
20.6
880 x 520 x 127
C (1.5V × 1)
4.2
1.5
10.4
RB-9312N-GBS
17.7
880 x 520 x 112
C (1.5V × 1) 3.5 x 2
—
—
6.8
RB-9313N-GBSU
19.2
880 x 520 x 112
C (1.5V × 1)
2.9
1.5
7.8
(mm)
268 x 490
C (1.5V × 1)
R0~R50
5.0
5.0
5.0
3.5
Gas
Type of
Connecting
gas
Tube
L.P.G
(30 mbar)
ø 9.5 mm
gas specific
rubber hose
19
http://www.rinnai.com
20