Therma-Tron-X, Inc.

SlideRail Square Transfer (SST) Electrocoating Systems
Black acrylic primer is applied to flywheels and
assorted small parts in baskets for a contract
shop specializing in automotive coating. The
SST system includes a roller conveyor for
loading and unloading.
High capacity
electrocoating
in a
fraction of the
floor space
• 12-stage zinc phosphating pretreatment
• 8’6” wide by 6’0” high by 4’6” long work
envelope
• 267 square feet per minute at 20 loads
per hour
• 4,000 lb. capacity per load
A commercial lawn care equipment manufacturer employs this cathodic two color SST
system to electrocoat sheet metal components
and heavy steel frames with acrylic paint.
• 15-stage zinc phosphating pretreatment
• 9’0” wide by 6’0” high by 4’0” wide work
envelope
• 133 square feet per minute at 20 loads
per hour
• 1,000 lb. capacity per load
This SST E-coat system applies a tough gray
epoxy coating to blower and fan components.
• 8-stage iron phosphating pretreatment
• 9’0” wide by 5’0” high by 4’0” long work
envelope
• 133 square feet per minute at 20 loads
per hour
• 1,000 lb. capacity per load
SlideRail Square TransferTM (SST) electrocoating
systems from Therma-Tron-X are unlike any other
equipment in the finishing business. Product indexes
along a pair of low maintenance slide rails, rather than
a traditional chain track. Because parts vertically enter
and exit the process stages, SST systems provide
electrocoating with complete immersion pretreatment
in a fraction of the space required by monorail systems
- and with greatly reduced tank charge costs.
The SST concept permits the application of multiple
processing alternatives through Programmable Logic
Controller (PLC) load management. The PLC can
supervise the simultaneous pretreatment of varied
substrates and selectively electrocoat products in
different color paint tanks. Automatic Voltage Control
(AVC) adjusts applied voltage in the E-coat tank to
match the square footage of the load, which prevents
overcoating and saves both electricity and paint. The
system may also be programmed to lengthen immersion time - ensuring proper coating thickness, even if a
load exceeds the rated maximum square footage.
This cathodic SST system electrocoats various
carbon steel parts for a first tier automotive
supplier based in Mexico.
Stainless steel construction gives Therma-Tron-X SST
systems long lasting durability. Multiple zone ovens
include a dehydration section to minimize bleed-out, a
cure zone and forced air cooling tunnel. SSTs may be
equipped with an indexing carousel loop for stationary
onloading and offloading of product, or directly linked
by conveyor to fabrication, assembly and shipping areas
of your plant to streamline your manufacturing process.
ECON-E-COAT TM
systems offer the same high throughput SST capabilities in a smaller work envelope with a
more modest capital investment - and are shipped fully
assembled and pre-tested. In fact, modular construction
allows for rapid installation of any SST system. Plus, all
Therma-Tron-X electrocoating systems may be equipped with complete water conditioning and wastewater
treatment equipment from TTX Environmental.
SlideRail Square Transfer systems
are the perfect solution for
electrocoating operations of any size
SST E-Coat Options
• Rack or Barrel Electrocoating
• Multiple Color Capabilities
• 11-stage zinc phosphating pretreatment
• 9’6” wide by 5’0” high by 5’0” long work
envelope
• 252 square feet per minute at 20 loads
per hour
• 2,865 lb. capacity per load
• Multiple Pretreatment Alternatives
• Spray and Immersion Pretreatment
Capabilities
• Acid Clean with Iron Removal
• Overhead and Side Transfer Cure Oven
Configurations
• Load Oscillation to Remove Trapped Air
• Automatic Voltage Control (AVC)
• Automatic Chemical Feeds
• Automatic Startup
• Complete Documentation Package
for Process Information Analysis
An SST ECON-E-COAT system applies black
epoxy primer on assorted steel parts for a
contract shop coater.
• 11-stage zinc phosphating pretreatment
• 5’0” wide by 2’0” high by 1’6” long work
envelope
• 17 square feet per minute at 20 loads
per hour
• 350 lb. capacity per load
Monorail Electrocoating Systems
Dependable
design
coupled with
time-proven
reliability
Tool box components are given a bright red
acrylic finish in this anodic electrocoating
system.
• 9-stage iron phosphating pretreatment
• 2’6” wide by 5’0” high work envelope
• 400 square feet per minute at 15 FPM
Wheels for agricultural implements are coated
with a white epoxy primer on this variable
speed monorail E-coat system.
• 7-stage iron phosphating pretreatment
• 1’10” wide by 3’0” high work envelope
• 94 square feet per minute at 12 to 20 FPM
This monorail electrocoating system applies a
tough epoxy primer to truck, trailer and farm
implement wheels.
• 6-stage iron phosphating pretreatment
• 4’0” wide by 5’0” high work envelope
• 144 square feet per minute at 10 FPM
Years of research, experience and engineering
innovation go into every Therma-Tron-X
electrocoating system. Our reputation has been built
on the success of our many satisfied customers
throughout North America and overseas.
TTX monorail E-coat systems feature SpiraFlowTM
tank design which enhances paint circulation without
clumping, settling or foaming. Solution spirals
throughout the length of inclined, round bottomed
tanks, ensuring that paint reaches and thoroughly
covers every square inch of your parts - including
those with complex configurations. Dead spots are
virtually eliminated.
Tanks may be specified with all stainless steel
construction for longer life and lower maintenance
costs. Phosphate stage heating by external plate
and frame heat exchanger is available, and all stages
are typically enclosed and exhausted to conserve
energy costs and shield products from plant
contamination.
Conveyor deterioration is minimized by suspending
parts through slotted roofs on process tank
enclosures, protecting track and chain from corrosive atmospheres. Our “Current Collector” conveyor
grounding mechanism eliminates mechanical
adjustments necessary on other grounding systems.
This exclusive TTX counterweighted design maintains
excellent contact for a much longer period of time
because it does not lose efficiency through wear.
Therma-Tron-X electrocoating systems are
managed by Programmable Logic Controller (PLC)
hardware. System data such as tank levels, applied
voltage and oven temperatures are monitored to
ensure that all operating parameters remain within
specifications. The PLC may be programmed for
automatic system startup, automatic feed of bath
chemicals and paint replenishment based on
production levels, among many other options. It can
also track loads of product through the system and
interface with our optional documentation software,
which downloads data for trending,
graphing and process analysis.
Other system options include varied
pretreatment alternatives and multiple
color capabilities. Pretreatment and postrinse stages are available in both spray
and immersion configurations. ThermaTron-X has also supplied combination
monorail systems which apply a powder
or liquid topcoat over an E-coat primer.
Conveyor integration with fabrication,
assembly and shipping departments can
assist in maximizing productivity.
With Therma-Tron-X,
you get the skill and knowhow of a world leader in
electrocoating technology.
This monorail electrocoating system applies a
black epoxy primer on steel components for
recreational vehicles.
• 11-stage zinc phosphating pretreatment
• 3’0” wide by 5’0” high work envelope
• 200 square feet per minute at 12 FPM
Shopping carts and various other wire products
receive an epoxy primer in this monorail E-coat
system.
• 4-stage zinc phosphating addition to
existing pretreatment system
• 2’6” wide by 6’0” high work envelope
• 60 square feet per minute at 8 FPM
SlideRail Square Transfer (SST) Systems
The
versatile
solution
for
industrial
coating
This SST powder system coats large weldments
and other components for a maker of material
handling equipment.
• 7-stage zinc phosphating pretreatment
• 15’6” wide by 6’0” high by 6’0” long work
envelope
• 3,600 lb. capacity per load
A building components manufacturer with
contract shop capabilities employs this SST
powder system to coat steel and aluminum
products. The system includes a programmed
hoist for loading and unloading.
• 14-stage pretreatment processes both steel
and aluminum parts
• 30’0” wide by 5’0” high by 1’6” long work
envelope
• 1,200 lb. capacity per load
Scissors manlift components receive a tough,
long lasting finish on this SST powder coating
system. Parts undergo pretreatment and dryoff
in one SST, are transferred to power & free
conveyor for coating, and cured in a separate
SST oven.
• 8-stage iron phosphating pretreatment
• 11’6” wide by 6’7” high by 3’0” long work
envelope
• 1,500 lb. capacity per load
The SlideRail Square TransferTM (SST) material
handling concept from Therma-Tron-X offers a
combination of versatility and high throughput
unmatched by other finishing conveyors. In addition
to electrocoating, SST systems have been used in
powder coating, heat processing and cleaning/
pretreatment operations with great success.
In an SST, parts index along a pair of low maintenance slide rails, rather than a traditional conveyor
track. Racks of product suspended from load bars
are lowered into and raised out of all tanks simultaneously before moving to the next stages in
unison. Because all loadbars are repositioned at the
same time, SSTs produce significantly greater output
than programmed hoists.
Therma-Tron-X SST systems offer complete
immersion processing in a fraction of the floor space
required by monorail systems. Vertical product entry
and exit allows each stage to be sized only slightly
larger than the maximum work envelope - greatly
reducing tank charge costs. An indexing carousel
conveyor allows for stationary loading and unloading,
and SST ovens permit close banking for greater
capacity than other conveyorized ovens.
Programmable Logic Controller (PLC) hardware
monitors such data as tank levels and oven
temperatures to ensure that all operating parameters
remain within specifications. The PLC may be
programmed for automatic startup and addition of
bath chemicals based on production levels, among
many other options.
The PLC can also track loads of product through the
SST and apply custom processing alternatives. Plus,
our optional documentation software is able to
download operating parameters for trending, graphing
and analysis.
SlideRail Square Transfer
system technology is available
only from Therma-Tron-X.
The SST Advantage
SlideRail Square Transfer systems offer a
number of advantages over monorail systems
of equal capacity. Among these are:
Heavy weldments are powder coated in this
SST system with integral dryoff oven and
powder room.
• 4-stage iron phosphating pretreatment
• 16’0” wide by 2’8” high by 3’6” long work
envelope
• 3,000 lb. capacity per load
• Maximum utilization of plant floor space
• Modular construction for faster installation
• Loading and unloading from stationary
conveyor positions
• Closer racking of parts for higher
production throughput
• Greatly reduced tank charge costs
• Less water and chemical usage due to
efficient utilization of multiple rinse
stages
• Lower maintenance and utilities costs
This SST immersion cleaning and deoxidizing
system treats windshield wiper head casings for
a automotive tier supplier on the U.S./Mexico
border.
• 5-stage aluminum pretreatment
• 5’0” wide by 2’0” high by 1’6” long work
envelope
• 200 lb. capacity per load
Monorail Powder/Liquid Coating Systems
Precision
engineered
to best
meet your
process
requirements
A manufacturer of major home appliances
employs this 30 FPM monorail powder coating
system to process upright and chest freezers.
• 7-stage iron phosphating pretreatment
• 3’0” wide by 6’2” high work envelope
• 3,200 foot, 4-inch I-beam conveyor
This 3 FPM powder system puts a corrosion and
chemical resistant coating on processing
machinery components for a manufacturer of
paper industry equipment.
• 4-stage iron phosphating pretreatment
• 2’8” wide by 5’8” high work envelope
• Enclosed track conveyor
This 10 FPM monorail powder system applies a
protective gray coating for a manufacturer of
antenna dishes.
• 7-stage zinc phosphating pretreatment
• 2’0” wide by 4’6” high work envelope
• Combination dryoff/cure oven with infrared
preheat section
• Enclosed track conveyor
The design, manufacture and installation of complete
coating systems has long been a Therma-Tron-X
specialty. Our products have developed a reputation
for dependability by reliably serving hundreds of
customers in a wide range of industries.
Therma-Tron-X engineers evaluate plant space,
part configuration, coating requirements and
throughput capacities before recommending the
custom equipment and layout that best satisfies the
needs of your finishing operation. Our experience in
design, testing, fabrication and installation ensures
that your system will provide maximum value with
minimal investment.
Therma-Tron-X spray washers deliver the optimal
pretreatment combination of cleaning, conversion
coating, sealing and rinsing stages for any painting
process, and may be equipped with complete water
conditioning and wastewater treatment capabilities
from TTX Environmental. Spray and immersion
configurations are available, with immersion tanks
typically enclosed and exhausted to maintain
temperature uniformity and shield parts from plant
contamination.
booths to allow external conveyor
positioning - protecting parts from grease
and dirt while preventing premature
deterioration of track and chain.
Dryoff and cure ovens feature high efficiency heat
sources and fans offering precise performance
throughout while pinching pennies in fuel and utilities
consumption. Radiant heat sources are an option, as
well as combination systems that use infrared
vestibules to ramp up part temperature without
disturbing powder coatings, followed by a
conventional convection zone for curing.
Therma-Tron-X supplies climate controlled
environmental rooms, and works closely
with application equipment suppliers to
seamlessly integrate paint booths into any
coating operation. Multi-function control
panels keep all components operating
smoothly and may be equipped with
optional documentation software capable of
downloading system data for process
analysis.
Conveyors of any capacity and complexity not only
supply dependable material handling during the
coating process, but can also help to streamline
manufacturing as a whole by directly transferring
product between fabrication areas, paint department and final assembly or shipping locations.
Slotted roofs are standard in washers and spray
Therma-Tron-X finishing
systems stress
efficiency and reliability from cleaning to curing.
Automotive parts - primarily seating components - are coated by a contract shop using this
8 FPM powder system.
• 6-stage iron phosphating pretreatment
• 1’0” wide by 4’0” high work envelope
• Enclosed track conveyor
A contract shop coater processes assorted steel
parts with this 10 FPM powder system.
• 10-stage iron phosphating pretreatment
• 5’0” wide by 5’0” high work envelope
• 4-inch I-beam conveyor
Combination Coating Lines
Complete
systems
for efficient
multiple coating
operations
Assorted aluminum products are processed in
this 10 FPM monorail electrocoat/powder
topcoat system employed by a contract shop.
•
•
•
•
8-stage aluminum pretreatment
2’10” wide by 4’4” high work envelope
150 square feet per minute
Inverted enclosed track conveyor
Electrical transformer tanks receive an epoxy
primer and acrylic topcoat in this two-coat SST
electrocoating system.
• 8-stage zinc phosphating pretreatment
• 12’0” wide by 5’0” high by 4’0” long work
envelope
• 150 square feet per minute at 17 loads
per hour
• 900 lb. capacity per load
This SST electrocoating system with liquid topcoat
serves a maker of truck utility bodies. Automatic
load bunching allows simultaneous processing of
single or multiple loadbars.
• 8-stage zinc phosphating pretreatment
• 22’6” wide by 10’0” high by 12’0” long work
envelope
• 200 square feet per minute at 12 to 15 loads
per hour
• Power and free conveyor transfers parts from
multiple fabrication areas to the E-coat
system and then to the topcoating booth
Continuing public demand for high quality products
means that manufacturers are turning more often to
combination coatings to maximize the protective and
attractive aspects of their finishes.
These coatings begin with a premium pretreatment
process for superior basecoat adhesion. Electrocoating is the preferred primer because of its allaround durability and corrosion resistance. A liquid or
powder topcoat is then added for high gloss,
endurance against fading due to UV exposure and
quick color changes. Two-coat electrocoating systems
apply a second E-coat layer over the primer for
maximum protection against the elements.
Therma-Tron-X finishing system construction
matches the durability and reliability of these high
performance coatings. We offer a wide range of
material handling capabilities to meet every requirement of your operation. Our SlideRail Square
Transfer TM (SST) systems have the advantage of
total immersion pretreatment in a fraction of the floor
space required by monorails.
This SST system applies an E-coat primer and
powder topcoat to steel and aluminum lighting
products as large as thirty foot poles.
SSTs may be programmed with a “rack bunching”
option to handle differing size loads and multiple
loads with peak efficiency. Larger parts enter the
pretreatment/electrocoat system on a single carrier,
while smaller parts may be grouped two or even
three loadbars to a tank to maximize throughput.
After the primer is cured, loadbars are ungrouped
and banked before automatic transfer to the topcoating line. This ensures a steady stream of product
racked with adequate density for efficient topcoating.
Systems are monitored and managed by reliable PLC
hardware, with optional documentation software able
to download and analyze system data. ThermaTron-X also handles integration of topcoating booths
and supplies environmental rooms for paint storage
and spray coating operations.
When a tough combination
coating is essential,
your best finish starts with
a Therma-Tron-X paint system.
Combination Paint Systems
w Configuration Options w
Conveyor Type
SlideRail Square Transfer (SST)
• 14-stage pretreatment simultaneously
processes both steel and aluminum
• 30’0” wide by 3’0” high by 2’0” long work
envelope
• 150 square feet per minute at 20 loads
per hour
• 1,000 lb. capacity per load
• Power & free conveyor for powder application
Monorail w Power & Free
Inverted Power & Free
Programmed Hoist
Manual Transfer
Pretreatment
Zinc Phosphate
Iron Phosphate
w Aluminum Etch
Prime Coat
Epoxy E-Coat
w Acrylic E-Coat
Topcoat
Acrylic E-Coat
Powder
w Liquid Spray
An epoxy electrocoat primer and powder
topcoat combination are applied by a contract
shop coater to automotive luggage racks on this
9 FPM monorail system.
•
•
•
•
10-stage aluminum pretreatment
4’0” wide by 6’5” high work envelope
175 square feet per minute
Inverted enclosed track conveyor
Finishing System Components and Programmed Hoists
Pretreatment Systems
Conveyor Systems
Thorough pretreatment assists greatly in
corrosion resistance and paint adhesion - simplifying
the coating process and improving the appearance
of the product while adding years to its useful life.
Optimum design and execution in the building of
pretreatment systems is a Therma-Tron-X
strength. Stainless steel washer construction
permits the use of reverse osmosis or deionized
rinse water, while slotted roofs protect conveyor
components from corrosion and products from
contamination. Our many years of experience
enable us to engineer a system around your parts
and your processes.
Multiple counterflow technology greatly reduces
water use and decreases solution dragout. Coupled
with complete water conditioning and wastewater
treatment from TTX Environmental, your ThermaTron-X pretreatment system will provide
consistently clean parts with lower operating costs using fewer chemicals and less plant water while
minimizing generated waste.
Every Therma-Tron-X conveyor system is unique
in configuration, load and process requirements.
Our experience in the design, fabrication and
installation of conveyors allows us to meet every
challenge presented by the material handling aspects
of your finishing process.
Therma-Tron-X pretreatment
systems maximize cleaning
power through optimal design
- including spray nozzle
arrangements specific to parts
and process.
Therma-Tron-X conveyor
systems satisfy any level of
capacity and complexity
through CAD-designed layouts
that process products with
superior efficiency.
Industrial Ovens
Most industrial processes require some application
of heat. Our experience with a wide range of heating
equipment and processes means that you can depend
on Therma-Tron-X for a high efficiency oven system
that meets or exceeds the specifications of your
finishing operation.
Conveyorized and batch designs are available with
electric, oil, steam, gas or infrared heat sources. Our
ovens feature aluminized steel interiors and exteriors
with semi-rigid, non-settling mineral wool insulation.
Blowers, fans and ductwork are sized for optimal air
circulation, resulting in strict temperature tolerances
throughout the entire oven. Heater boxes are
assembled and tested in our plant prior to shipment.
Therma-Tron-X also makes a variety of specialized
heating apparatus: aluminum aging ovens, coil potting
equipment, fluxers, palletizing shrink wrap ovens and
baking and dehydration ovens for use in the food
industry. You can count on our heat processing systems to provide the exacting performance demanded
by today’s stringent manufacturing procedures.
Reliable Therma-Tron-X conveyors are CAD-designed
and PLC controlled for high capacity performance.
Continuous monorail, power and free, inverted power
and free, flat belt, roller type and chain-on-edge
systems dependably automate any finishing operation,
and may include transfer devices which readily link to
existing plant conveyors.
We design our equipment with maintenance in mind.
Washers and paint application booths have slotted
roofs to protect conveyor components from moisture
that causes premature deterioration of track and chain,
resulting in poor grounding and coating contamination.
Conveyors are equipped with automatic lubrication and
chain take-up systems to decrease wear, extend
operational life and minimize downtime.
Programmed Hoists
Therma-Tron-X ovens
are equipped with high
efficiency burners and fuel
modulation components to
minimize operating costs while
maximizing productivity.
Therma-Tron-X multiple
speed lift and travel hoists
are capable of automating a
wide range of finishing
operations for businesses of
any size.
Programmed hoist systems from Therma-Tron-X
are custom built to serve a wide variety of industrial
finishing processes: rack or barrel electrocoating, dip
coating, zinc or iron phosphating and alkaline cleaning.
Our multiple speed lift and travel hoists are equipped with
long lasting, high reliability components to handle the
heaviest workloads and feature tanks built of durable
stainless steel - unlike the plastic construction often used
by other equipment manufacturers.
Dependable PLC hardware monitors every aspect of the
system. Loads may be run on a fixed recipe or random
access basis. Radio frequency controls allow remote
operation, and our laser positioning system ensures
accurate high speed location of racks or barrels at each
stage. Options include automatic control of chemical and
paint feeds, auto shutdown/alarm management and
process information downloading.
Two or more hoists may be combined to maximize
throughput, and may be interconnected with other plant
areas to streamline production. Bulk loading and
unloading equipment is also available from TTX.
Water Treatment Equipment
Therma-Tron-X Technology
Optimizing the design
of your system ...
Custom systems built
around your wastewater
Wastewater treatment steps required by any company
depends on the specific nature of their business.
Engineers from TTX Environmental will evaluate
your waste stream and recommend the best
combination of physical and chemical treatment
processes to bring your plant into compliance with
federal, state and local discharge standards.
At Therma-Tron-X, innovation has remained the
driving force behind our continued success. Our
technology, however, goes far beyond the use of
computer aided design (CAD). We utilize software that
performs virtual stress tests and deflection analysis on
equipment components before the first drawings ever
reach our shop floor. Other programs estimate dragout
and determine rinse ratios to make our pretreatment
systems as efficient as possible and calculate waste
creation for correct sizing of wastewater treatment
systems.
Our wastewater treatment systems recycle cleaners,
neutralize acids and alkalis, precipitate metals,
detackify paints, clarify output water and concentrate
solids for disposal. Sumpless collection systems can be
operated on a batch or continuous basis, depending
on volume.
TTX has long been an industry pioneer in conveyor
grounding and automatic voltage control (AVC). Our
E-coat tanks ensure excellent circulation without foaming
or settling, and our revolutionary SlideRail Square
Transfer TM (SST) material handling concept maximizes
throughput in minimal plant space. At Therma-Tron-X,
we don’t just employ the latest technologies in finishing
system design - we create them.
Environmental efficiency is stressed through waste
minimization and process bath reclamation to lower
operational costs. Modular system components
provide ease of installation and flexibility for future
expansion in minimal floor space. Several TTX
Environmental customers have received governmental awards for waste remediation in their plants.
High quality water for
high quality finishing
Study after study has verified that the use of clean
process water is essential to any finishing operation.
This is especially true of critical areas like plating baths,
electrocoating tank makeup and final pretreatment
rinses. Water conditioning equipment from TTX
Environmental meets the needs of our finishing system
customers and other manufacturers for whom water with
low total dissolved solids (TDS) plays an important role.
Reverse osmosis (RO) conditioning systems are the
finishing industry standard for production of clean water.
Reverse osmosis provides low cost, low TDS water
without hazardous chemicals and with no byproducts
requiring treatment prior to discharge.
When fed by an RO unit, a deionization (DI) system will
supply ultra pure water at a reasonable per unit price.
TTX Environmental also offers a wide range of water
conditioning system components, including dealkalization
units, water softeners, sand and ultraviolet filters, and
degasifiers for CO2 removal.
… and maximizing
its performance
To aid you in running your equipment at peak efficiency,
Therma-Tron-X offers an optional documentation
package which ties a personal computer to your system
control panel. This computer software tracks system
resources; records, stores and analyzes process
variables; and suggests adjustments that may be made
to help your equipment run at optimal levels.
The program automatically downloads raw data which
may be graphed or charted. It can be set up to calculate
all costs involved in the finishing process, visualize alarm
trends, track tank chemistries, monitor oven
temperatures, calculate product through-put and
determine cost per unit of finished product, among many
other functions.
If unsatisfactory parts are produced, system parameters
can be retrieved from the period during which those
parts were processed. Information may also be
downloaded and sent electronically to Therma-Tron-X
for remote engineering analysis.
Operating manuals for Therma-Tron-X finishing
systems are available on CD-ROM.
Therma-Tron-X began manufacturing custom industrial ovens in the summer of 1971,
and our original Sturgeon Bay facility was constructed in 1976. Since that time, our
headquarters has expanded more than six-fold in response to ever increasing demand for
our quality heat processing equipment, washers, programmed hoists, environmental
products and complete paint systems.
Because every product we make presents unique challenges in process, part configuration
and space limitations, we must treat each of our customers on an individual basis. As a
Therma-Tron-X client, you will receive a
quote on the finishing equipment that best fits
your operational requirements. Then we ask you, along with your chemical and paint
suppliers and other vendors, to work with us every step of the way to ensure that the
equipment we design, build and install meets your highest expectations.
As a full service supplier, Therma-Tron-X handles every aspect of your purchase. We
combine creative engineering, state-of-the-art computer design and hard working personnel
to maximize the value of your system - meeting the needs of your business both today and
well into the future.
We take great pride in making things right.
Therma-Tron-X, Inc.
s Your best finish starts with us s
1155 S. Neenah Avenue • Sturgeon Bay, WI 54235-1996
Phone - 920/743-6568 • Fax - 920/743-5486
Website - www.therma-tron-x.com • E-mail - [email protected]
A subsidiary of
Holdings, Inc.