bia retail advantages - BIA systeemwanden en wandpanelen

BIA RETAIL WALLS
1
RETAIL PRODUCT LINE
MDF PLAIN 12 MM GROOVE/BLADE
/ CONNECTION
BEADING WHITE
TELESCOPIC ANTENNA with GRID
METAL S-CLIP
MDF PREFAB-CORNER CONNECTION
MULTIPLEX FLOOR BEADING
2
BIA RETAIL ADVANTAGES
01) BIA Walls are detachable and can be re-used for up to 2 or 3 times
02) MDF Prefab Corners “no additional modifications during assembling”
03) Electronic cables can be placed everywhere and without any difficulties
04) Telescopic antenna can be assembled on any desired place
05) Beading white can be used for lower cross-cut ends and low walls
05) Multiplex Floor beading processed with 2-sided duct-tape
06) S-Clips for detachable building
07) BIA Walls are light “less physical stress for builders”
08) Mouse-friendly, no breeding ground for mice.
09) All materials are fully recycable
3
BIA RETAIL PRICES
MDF Panel Groove and Blade Connection
12 mm MDF Plain – Core 40 mm – 12 MDF Plain
Breadth Panel 600 mm
Panel height
2600 mm
2900 mm
3400 mm
Price per M2
on request
,,
,,
Prefab Corner Solution
2600 mm
2900 mm
3400 mm
Price per Corner
on request
,,
,,
Profiles
Wood Beading White 9010
Length 2600 mm – Inside measure 64 mm
Price / Each
on request
Multiplex Floor Beading
Length 2440 mm – Heightened 18-64-40 mm
,,
Metal S-Clip
,,
Telescopic Arm RAL 9010
With Plug-in Profile 600 mm + Ceiling grid
,,
GENERAL ORDER CONDITIONS
1) Ex-factory Prices, net and ex btw
2) The delivery address is the storeroom or project address
3) Freight is unloaded next to truck with the help of fork-lift truck
4) Delivery time standard products deliverable from supply
5) Transport tariffs conform price list bia
6) At height 3400 being delivered in length of 2150 mm and 1250 mm
7) Sawing, before delivery we can saw till any desired height
8) Additional prices for implementation mdf optical fibre
9) Additional prices for the production of prefab units or modules
10) We act within the delivery conditions of NEBIFA/BIA
4
RETAIL BEADING WHITE
5
RETAIL FLOOR CONNECTION 64 MM
The heightned floor beading is especially designed to compensate for the influence in
height in the long Floor elements.
WALL CONNECTION
As you can see in the picture below, the BIA System walls can be moved over the
wall beading. The long sides of the system wall, which are moved over the wall
beadings, have to be equipped with assembling glue (for permanent installation).
6
RE-USING THE PANELS
If the wall is only placed temporarily, an S-OBI can be used. By folding this plate,
they fit easily in open spaces of the BIA Panel. This s-obi can be montaged to the
floor and ceiling.
If the wall is placed temporarily, S-clips can be used rather than glue in order to connect the
panels interdependently. These are moved on the top side of the card board. During
disassembly there is little to no demolition waste and the panels can be re-used.
7
PERMANENT INSTALLATION
For permanent installation the panels can be glued to one another with Conlit-Fix®
(Spanell glue). This needs to be applied on the inner side of the plasterboard that is
sticking out. The glue is fire-resistant.
T-CONNECTION
To create a so-called “T-connection”, i.e. a wall perpendicular to another Spanell wall,
an MDF assembly beading is attached on the already installed wall and the floor over
which the bia system wall can be placed.
8
CORNER CONNECTION “PREFAB”
The prefab corner connections are composed factory-wise, so that the continuity of
building in practice is safeguarded without too many modifications and there is a
possibility to gain significant time advantage.
9
WINDOW-FRAMES AND DOOR-FRAMES
For the assemblance of doors and windows an opening can be sawed in the already
installed bia system wall. This opening can be sawed in any desired area. It is also
possible to keep the openings during the building of the door-frames, especially for
projects with relatively many doors, this saves m2 of material. Afterwards there needs
to be installed a wooden profile (assembly beading) on the inside between the two
outside panels, so that the system frames can clamp on the plate material. Finally,
the door or window can be closed.
Another possibility is to place the frames beforehand. The wall with Spanell panels
can then be placed around this.
PLUG-SOCKET WIRING
The wiring can be placed anywhere. The space between the modulated card board is
large enough to install the wiring.
10
WALL OUTLETS
If the wiring has been placed, the holes can be drilled, the firm Attema has wall
outlets which can be easily assembled in the walls.
11
TELESCOPIC ANTENNA
There is a variety in lengths amongst the telescopic antennas, the plug-in arm
(lengths of 600, 750 and 2200 mm) can be attached to the modulated card board of
the wall. With the use of a ceiling grid attachment the antenna can be pinned to the
upper wiring.
Check our website for reference projects
www.bia-systeemwanden.nl/referenties
12
This information applies to all types of Spanell system walls.
Transport and storage:
The Spanell panels are sealed in plastic foil on cardboard pallets and then
transported per 22 or 30 panels per pallet. During transport the pallets may be piled
up to an absolute maximum of 2 pallets. The Spanell panels are preferably delivered
after the completion of the brickwork, pargeting, etc. The Spanell panels have to be
shipped horizontally and in dry circumstances. During storage the Spanell panels
should be kept in a dry environment, should be stored flat, horizontally, preferably on
a pallet for support. During storage the Spanell panels may not be piled up.
Processing conditions:
The Spanell panels have to be kept away from water or any other form of liquid or
humid environment at any time. If a change of humidity occurs, the plate will expand
or shrink. Only certified and approved equipment should be used for sawing, cutting
and drilling. Walls higher than 3400 mm are built in “1/2 stone connection”. To a
height of approximately 6 meters this can be done without additional
consolidation/architectural measures.
Attaching of objects:
Light objects to a weight of 5 kg can be put up with nails and hooks. If wall plugs are
used heavier objects to a weight of 30 kg can be put up in case of single-plated walls
and for double-plated walls objects up to a weight of 50 kg can be put up. In case of
heavier objects (i.e. heavier than 30 kg, respectively 50 kg) trapezium wood backing
and consoles should be applied.
Durability and maintenance:
To guarantee durability the Spanell wall needs to be set up as has been previously
specified. Maintenance and possible necessary repair has to be performed in a timely
manner. Speaking from experience the maintenance of the walls has to be performed
with traditional materials and products and in accordance with the processing
prescriptions of the supplier
13
Delivery conditions:
We strive for a continuous improvement of our products. Consequently we reserve all
rights to expand, scale down or otherwise alter our product line and other details or
specifications without foregoing announcement. Our products are fabricated with
utmost care and concern to avoid any material defects
Regarding our terms of responsibility and guarantees we refer to our NEBIFA
delivery conditions which can be requested at BIA Systeemwanden
KOMO ATTEST
BIA Systeemwanden B.V.
Almereweg 25
1671 ND MEDEMBLIK
T 0031 227 570 622
F 0031 227 542 782
W www.bia-systeemwanden.nl
SALES
John Giltjes
G 0031 6 20 11 28 65
E [email protected]
14