TGP2109-SM
Transcription
TGP2109-SM
TGP2109-SM 8-12 6-Bit Digital Phase Shifter Applications • X-Band Radar • Satellite Communication Systems QFN 4x4 mm 16L Product Features • • • • • • • • • • • • • Functional Block Diagram Frequency Range: 8 to 12 GHz 6-Bit Digital Phase Shifter Bi-Directional 360° Coverage, LSB = 5.625° RMS Phase Error: 4° RMS Amplitude Error: 0.5 dB Insertion Loss: 6 dB Return Loss: 10 dB IRL; 15 dB ORL Input P1dB: 29 dBm Input IP3: >40 dBm IM3: <-50 dBc Control Voltage: 0/+5 V QFN Package Dimensions: 4.0 x 4.0 x 1.64 mm General Description Pin Configuration The Qorvo TGP2109-SM is a packaged 6-bit digital phase shifter fabricated on Qorvo’s high performance 0.15μm GaAs pHEMT process. It operates over 8 to 12 GHz and provides 360° of phase coverage with a LSB of 5.625°. It also achieves a low RMS phase error of 4° with 6 dB of insertion loss. The TGP2109-SM was developed for simply system integration. It uses positive only switch logic eliminating the need for a negative voltage rail. In addition, both ports are matched to 50 ohms with DC blocking capacitors. Ease of use along with low insertion loss and a high degree of resolution makes the TGP2109-SM ideally suited for a variety of x-band phased array applications including commercial and military radars and phase array communication systems. The device is lead-free and RoHS compliant. Evaluation Boards are available upon request. Datasheet: Rev - 9-30-15 © 2015 Qorvo Pin No. Symbol 1, 3, 9, 11, 17 2 GND RF In 4, 16 N/C 5 6, 14 7 8 10 12 13 15 90° Bit REF 180° Bit 5° Bit RF Out 22° Bit 45° Bit 11° Bit Ordering Information Part TGP2109-SM - 1 of 16 - ECCN EAR99 Description 8-12GHz 6-Bit Digital Phase Shifter Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Absolute Maximum Ratings Parameter Recommended Operating Conditions Value Parameter Value Control and Reference Voltage Control Current Power Dissipation Input Power, CW, 50 Ω, 85°C Channel Temperature 6V 0.5 mA 1.5 W 33 dBm 200 °C Control Voltage (50, 110, 220, 450, 900, 1800) Reference Voltage (VREF) Current (IREF, ICTRL) 0/+5 V +5 V < 50 µA Mounting Temperature (30 Seconds) 260 °C Storage Temperature Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all operating conditions. -55 to 150 °C Operation of this device outside the parameter ranges given above may cause permanent damage. These are stress ratings only, and functional operation of the device at these conditions is not implied. Electrical Specifications Test conditions unless otherwise noted: 25°C. Control Voltage (REF, 50, 110, 220, 450, 900, 1800) = 0/+5 V; See Bias Truth Table. Parameter Min Operational Frequency Range Insertion Loss Input Return Loss Output Return Loss RMS Phase Error RMS Amplitude Error Input P1dB Input IP3 (Tone Spacing = 10 MHz, Pin/Tone = 16 dBm) IM3 (Tone Spacing = 10 MHz, Pin/Tone = 16 dBm) Insertion Loss Temperature Coefficient Typical 8 Max Units 12 GHz dB dB dB deg dB dBm dBm dBc dB/°C 6 10 15 4 0.5 29 > 40 < -50 0.004 Bias Truth Table Logic “0” = 0 V, Logic “1” = VREF = +5 V Phase Shifter 50 110 220 450 900 1800 REF 0° (Reference) 5° 11° 22° 45° 90° 180° 355° 0 1 0 0 0 0 0 1 0 0 1 0 0 0 0 1 1 1 1 0 1 1 1 0 1 1 1 1 0 1 1 0 1 1 1 1 1 0 1 0 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 Datasheet: Rev - 9-30-15 © 2015 Qorvo - 2 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Thermal and Reliability Information Parameter Test Conditions Value Units Channel Temperature (TCH) Median Lifetime (TM) TBASEPLATE = 85°C 85 5.2E+9 °C Hrs Notes: 1. Under normal (lifetime) operating conditions, self-heating is not a significant contributor to channel temperature. Median Lifetime Median Lifetime vs. Channel Temperature Median Lifetime, TM (Hours) 1E+15 1E+14 1E+13 1E+12 1E+11 1E+10 1E+09 1E+08 1E+07 1E+06 1E+05 1E+04 1E+03 FET5 25 50 75 100 125 150 175 200 Channel Temperature, TCH (°C) Datasheet: Rev - 9-30-15 © 2015 Qorvo - 3 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Typical Performance – Small Signal Test conditions unless otherwise noted: 5V and 3V, 25 °C RMS Phase Error vs. Freq. vs. Temp RMS Phase Error vs. Freq. vs. Temp VREF = 5 V, All Phase States VREF = 3 V, All Phase States 14 -40C 12 RMS Phase Error (degrees) RMS Phase Error (degrees) 14 +25C 10 +85C 8 6 4 2 -40C 12 +25C 10 +85C 8 6 4 2 0 0 6 7 8 9 10 11 Frequency (GHz) 12 13 6 14 RMS Amplitude Error vs. Freq vs. Temp. 7 RMS Amplitude Error (dB) RMS Amplitude Error (dB) +25C +85C 7 8 9 10 11 Frequency (GHz) 12 13 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 +85C 7 8 9 10 11 Frequency (GHz) 12 13 14 Avg. Insertion Loss vs. Freq. vs. Temp. VREF = 3 V, All Phase States -4 -4 -5 -5 -6 -6 S21 (dB) S21 (dB) 14 +25C VREF = 5 V, All Phase States -7 -40C +25C -9 13 -40C 6 14 Avg. Insertion Loss vs. Freq. vs. Temp. -8 12 VREF = 3 V, All Phase States -40C 6 9 10 11 Frequency (GHz) RMS Amplitude Error vs. Freq vs. Temp. VREF = 5 V, All Phase States 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 8 -7 -8 -40C +25C -9 +85C +85C -10 -10 6 7 8 Datasheet: Rev - 9-30-15 © 2015 Qorvo 9 10 11 Frequency (GHz) 12 13 14 6 - 4 of 16 - 7 8 9 10 11 Frequency (GHz) 12 13 14 Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Typical Performance – Small Signal (Cont.) Test conditions unless otherwise noted: 5V and 3V, 25 °C Avg. IRL vs. Freq. vs.Temp. Avg. IRL vs. Freq. vs.Temp. VREF = 3 V, All Phase States 0 0 -5 -5 -10 -10 S11 (dB) S11 (dB) VREF = 5 V, All Phase States -15 -15 -20 -40C -20 -40C -25 +25C -25 +25C +85C +85C -30 -30 7 8 9 10 11 Frequency (GHz) 12 13 6 14 7 8 9 10 11 Frequency (GHz) 12 IRL vs. Freq. IRL vs. Freq. VREF = 5 V, All Phase States, 25 0C VREF = 3 V, All Phase States, 25 0C 0 0 -5 -5 -10 -10 S11 (dB) S11 (dB) 6 -15 -20 Peak -25 14 -15 -20 Peak -25 Average Average -30 -30 6 7 8 9 10 11 Frequency (GHz) 12 13 6 14 Avg. ORL vs. Freq. vs. Temp 7 -5 -5 -10 -10 S22 (dB) 0 -15 -40C +25C -25 9 10 11 Frequency (GHz) 12 13 14 VREF = 3 V, All Phase States 0 -20 8 Avg. ORL vs. Freq. vs. Temp VREF = 5 V, All Phase States S22 (dB) 13 -15 -20 -40C +25C -25 +85C +85C -30 -30 6 7 8 Datasheet: Rev - 9-30-15 © 2015 Qorvo 9 10 11 Frequency (GHz) 12 13 6 14 - 5 of 16 - 7 8 9 10 11 Frequency (GHz) 12 13 14 Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Typical Performance – Small Signal (Cont.) ORL vs. Freq. ORL vs. Freq. VREF = 5 V, All Phase States, 25 0C VREF = 3 V, All Phase States, 25 0C 0 0 -5 -5 -10 -10 S22 (dB) S22 (dB) Test conditions unless otherwise noted: 5V and 3V, 25 °C -15 -20 Peak -25 -15 -20 Peak -25 Average Average -30 -30 6 7 8 Datasheet: Rev - 9-30-15 © 2015 Qorvo 9 10 11 Frequency (GHz) 12 13 6 14 - 6 of 16 - 7 8 9 10 11 Frequency (GHz) 12 13 14 Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Typical Performance – Large Signal Gain vs. Pin vs. Temperature Gain vs. Pin vs. Temperature VREF = 5 V, Freq. = 10 GHz, Phase State = 0 deg VREF = 3 V, Freq. = 10 GHz, Phase State = 0 deg -4 -4 -5 -5 -6 -6 Gain (dB) Gain (dB) Test conditions unless otherwise noted: 5V and 3V, 25 °C -7 -7 -8 -40C -8 -9 +25C -9 -40C +25C +85C +85C -10 -10 2 4 6 0 8 10 12 14 16 18 20 22 24 Pin (dBm) 8 10 12 14 16 18 20 22 24 Pin (dBm) Gain vs. Pin vs. Frequency -5 -5 -6 7 GHz 8 GHz 9 GHz 11 GHz 12 GHz 13 GHz 10 GHz -8 -6 -7 -8 7 GHz 8 GHz 9 GHz 11 GHz 12 GHz 13 GHz 10 GHz -9 -9 -10 -10 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) Gain vs. Pin vs. Major Phase States Gain vs. Pin vs. Major Phase States VREF = 5 V, Freq. = 10 GHz, 25 0C VREF = 3 V, Freq. = 10 GHz, 25 0C -4 -4 -5 -5 -6 -6 Gain (dB) Gain (dB) 6 VREF = 3 V, 25 0C, Phase State = 0 deg -4 -7 -8 -9 4 Gain vs. Pin vs. Frequency -4 -7 2 VREF = 5 V, 25 0C, Phase State = 0 deg Gain (dB) Gain (dB) 0 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg -7 -8 -9 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg -10 -10 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) Datasheet: Rev - 9-30-15 © 2015 Qorvo - 7 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Typical Performance – Large Signal (Cont.) Phase vs. Pin vs. Temperature Phase vs. Pin vs. Temperature VREF = 5 V, Freq. = 10 GHz, Phase State = 0 deg VREF = 3 V, Freq. = 10 GHz, Phase State = 0 deg 190 190 185 185 180 180 Phase (deg) Phase (deg) Test conditions unless otherwise noted: 5V and 3V, 25 °C 175 170 -40C 165 +25C 175 170 -40C +25C 165 +85C +85C 160 160 0 2 4 6 0 8 10 12 14 16 18 20 22 24 Pin (dBm) VREF = 3 V, 25 0C, Phase State = 0 deg 190 8 GHz 9 GHz 11 GHz 12 GHz 13 GHz 10 GHz 185 Phase (deg) Phase (deg) 7 GHz 170 7 GHz 8 GHz 9 GHz 11 GHz 12 GHz 13 GHz 10 GHz 180 175 170 165 165 160 160 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) Phase vs. Pin vs. Major Phase States Phase vs. Pin vs. Major Phase States VREF = 3 V, Freq. = 10 GHz, 25 0C VREF = 5 V, Freq. = 10 GHz, 25 0C 360 360 315 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg 270 Phase (deg) Phase (deg) 8 10 12 14 16 18 20 22 24 Pin (dBm) Phase vs. Pin vs. Frequency 175 270 6 VREF = 5 V, 25 0C, Phase State = 0 deg 180 315 4 Phase vs. Pin vs. Frequency 190 185 2 225 180 135 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg 225 180 135 90 90 45 45 0 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) Datasheet: Rev - 9-30-15 © 2015 Qorvo - 8 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Typical Performance – Large Signal (Cont.) Test conditions unless otherwise noted: 5V and 3V, 25 °C Current IREF vs. Pin vs. Temperature Current IREF vs. Pin vs. Temperature VREF = 5 V, Freq. = 10 GHz, Phase State = 0 deg VREF = 3 V, Freq. = 10 GHz, Phase State = 0 deg 0.06 0.06 -40C -40C 0.05 +25C Current IREF (mA) Current IREF (mA) 0.05 +85C 0.04 0.03 0.02 0.01 0.03 0.02 0.00 0 2 4 6 8 10 12 14 16 18 20 22 24 Pin (dBm) 0 Current IREF vs. Pin vs. Frequency 6 8 10 12 14 16 18 20 22 24 Pin (dBm) 0.06 7 GHz 8 GHz 9 GHz 11 GHz 12 GHz 13 GHz 10 GHz 0.05 7 GHz 8 GHz 9 GHz 11 GHz 12 GHz 13 GHz 10 GHz Current IREF (mA) Current IREF (mA) 4 VREF = 3 V, 25 0C, Phase State = 0 deg 0.06 0.04 0.04 0.03 0.03 0.02 0.02 0.01 0.01 0.00 0.00 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) Current IREF vs. Pin vs. Phase States Current IREF vs. Pin vs. Phase States VREF = 5 V, Freq. = 10 GHz, 25 0C VREF = 3 V, Freq. = 10 GHz, 25 0C 0.06 0.06 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg 0.05 Current IREF (mA) Current IREF (mA) 2 Current IREF vs. Pin vs. Frequency VREF = 5 V, 25 0C, Phase State = 0 deg 0.05 +85C 0.04 0.01 0.00 0.05 +25C 0.04 0.03 0.02 0.01 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg 0.04 0.03 0.02 0.01 0.00 0.00 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) Datasheet: Rev - 9-30-15 © 2015 Qorvo 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Pin (dBm) - 9 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Typical Performance – Linearity ITOI vs. Freq. vs. Temperature ITOI vs. Freq. vs. Temperature VREF = 5 V, Pin/Tone = 16 dBm, Phase State = 0 deg VREF = 3 V, Pin/Tone = 16 dBm, Phase State = 0 deg 50 48 46 44 42 40 38 36 34 32 30 -40 C +25 C +85 C 6 7 8 9 10 11 Frequency (GHz) 12 13 50 48 46 44 42 40 38 36 34 32 30 -40 C +25 C +85 C 6 14 7 9 10 11 Frequency (GHz) 12 13 ITOI vs. Freq. vs. Pin/Tone ITOI vs. Freq. vs. Pin/Tone VREF = 3 V, 25 0C, Phase State = 0 deg 14 46 50 48 46 44 42 40 38 36 34 32 30 Pin = 0 dBm Pin = 2 dBm Pin = 4 dBm Pin = 6 dBm Pin = 10 dBm Pin = 16 dBm 44 Pin = 0 dBm Pin = 2 dBm Pin = 4 dBm Pin = 6 dBm Pin = 10 dBm Pin = 16 dBm 42 40 38 36 34 32 30 6 7 8 9 10 11 Frequency (GHz) 12 13 6 14 ITOI vs. Freq. vs. Major Phase States 7 6 7 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg 8 Datasheet: Rev - 9-30-15 © 2015 Qorvo 9 10 11 Frequency (GHz) 12 13 9 10 11 Frequency (GHz) 12 13 14 VREF = 3 V, Pin/Tone = 16 dBm, 25 0C ITOI (dBm) 50 48 46 44 42 40 38 36 34 32 30 8 ITOI vs. Freq. vs. Major Phase States VREF = 5 V, Pin/Tone = 16 dBm, 25 0C ITOI (dBm) 8 VREF = 5 V, 25 0C, Phase State = 0 deg ITOI (dBm) ITOI (dBm) ITOI (dBm) ITOI (dBm) Test conditions unless otherwise noted: 5V and 3V, Tone Spacing = 10 MHz, 25 °C 50 48 46 44 42 40 38 36 34 32 30 6 14 - 10 of 16 - 7 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg 8 9 10 11 Frequency (GHz) 12 13 14 Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Typical Performance – Linearity (Cont.) IM3 vs. Freq. vs. Temperature IM3 vs. Freq. vs. Temperature VREF = 5 V, Pin/Tone = 16 dBm, Phase State = 0 deg VREF = 3 V, Pin/Tone = 16 dBm, Phase State = 0 deg -30 -30 -40 -40 IM3 (dBc) IM3 (dBc) Test conditions unless otherwise noted: 5V and 3V, Tone Spacing = 10 MHz, 25 °C -50 -60 -50 -60 -40 C -40 C -70 -70 +25 C +25 C +85 C +85 C -80 -80 6 7 8 9 10 11 Frequency (GHz) 12 13 6 14 12 13 IM3 vs. Freq. vs. Pin/Tone VREF = 3 V, 25 0C, Phase State = 0 deg -30 Pin = 0 dBm Pin = 2 dBm Pin = 4 dBm Pin = 0 dBm Pin = 2 dBm Pin = 4 dBm Pin = 6 dBm Pin = 10 dBm Pin = 16 dBm Pin = 6 dBm Pin = 10 dBm Pin = 16 dBm 14 -40 IM3 (dBc) IM3 (dBc) 9 10 11 Frequency (GHz) IM3 vs. Freq. vs. Pin/Tone -50 -60 -50 -60 -70 -70 -80 -80 6 7 8 9 10 11 Frequency (GHz) 12 13 6 14 8 9 10 11 Frequency (GHz) 12 13 14 IM3 vs. Freq. vs. Major Phase States VREF = 5 V, Pin/Tone = 16 dBm, 25 0C VREF = 3 V, Pin/Tone = 16 dBm, 25 0C -30 -30 -40 -40 -50 -60 -70 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg 7 8 Datasheet: Rev - 9-30-15 © 2015 Qorvo 9 10 11 Frequency (GHz) 12 13 -50 -60 -70 0 deg 5 deg 11 deg 22 deg 45 deg 90 deg 180 deg 355 deg -80 -80 6 7 IM3 vs. Freq. vs. Major Phase States IM3 (dBc) IM3 (dBc) 8 VREF = 5 V, 25 0C, Phase State = 0 deg -30 -40 7 6 14 - 11 of 16 - 7 8 9 10 11 Frequency (GHz) 12 13 14 Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Applications Information De-Quing network is not required; VREF can be biased to either side of the package (pin #6 or #14) Evaluation Board RF layer is 0.008” thick Rogers RO4003C. Metal layers are 0.5-oz copper. Microstrip 50 Ω line width is 0.050”. The microstrip line taper at the connector interface is optimized for the Southwest Microwave end-launch connector 109202A-5. Ground / thermal vias under the DUT are critical for the proper performance of this device. The PCB shown herein utilizes copper filled vias (8 mils diameter) under the DUT. The pad pattern shown has been developed and tested for optimized assembly at TriQuint Semiconductor. The PCB land pattern has been developed to accommodate lead and package tolerances. Since surface mount processes vary from company to company, careful process development is recommended. Vias Pattern Datasheet: Rev - 9-30-15 © 2015 Qorvo - 12 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Pin Description Package Pad Symbol Description 1, 3, 9, 11 GND Internal grounding; must be grounded on PCB 2 RF Input Input; matched to 50 Ohms; DC blocked; interchangeable to RF Output 4, 16 N/C No Connectiion; recommend GND at the EVB level 5 90° 90° Bit 6, 14 REF Reference; VREF can be biased to either side of the packge 7 180° 180° Bit 8 5° 5° Bit 10 RF Output Output; matched to 50 Ohms; DC blocked; interchangeable to RF Input 12 22° 22° Bit 13 45° 45° Bit 15 11° 11° Bit GND On PCB; multiple vias should be employed under the center pad (17) to minimize inductance and thermal resistance; see page 12 for suggested vias layout 17 (Slug) Datasheet: Rev - 9-30-15 © 2015 Qorvo - 13 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Mechanical Information Package Information and Dimensions Units: mm Tolerances: unless specified .xx = ± 0.25 .xxx = ± 0.100 Materials: Lid: Plastic Base: Laminate Plating: All metalized features are NiPdAu plated Part is lead-free/PoHS-compliant; epoxy sealed Marking: 2109: Part number YY: Part Assembly year WW: Part Assembly week XXXX: Batch ID Datasheet: Rev - 9-30-15 © 2015 Qorvo - 14 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Recommended Soldering Temperature Profile Datasheet: Rev - 9-30-15 © 2015 Qorvo - 15 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com TGP2109-SM 8-12 6-Bit Digital Phase Shifter Product Compliance Information ESD Sensitivity Ratings Solderability Compatible with the latest version of J-STD-020 Lead free solder, 260 °C. Caution! ESD-Sensitive Device MSL Rating ESD Rating: TBD Value: TBD Test: Human Body Model (HBM) Standard: JEDEC Standard JESD22-A114 TBD at 260 °C convection reflow The part is rated Moisture Sensitivity Level TBD JEDEC standard IPC/JEDEC J-STD-020. ECCN RoHS Compliance U.S. Department of Commerce: EAR99 This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: • Lead Free • Halogen Free (Chlorine, Bromine) • Antimony Free • TBBP-A (C15H12Br402) Free • PFOS Free • SVHC Free Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.Qorvo.com Tel: +1.972.994.8465 Email: [email protected] Fax: +1.972.994.8504 Important Notice The information contained herein is believed to be reliable. Qorvo makes no warranties regarding the information contained herein. Qorvo assumes no responsibility or liability whatsoever for any of the information contained herein. Qorvo assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. Qorvo products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. For technical questions and application information: Email: [email protected] Datasheet: Rev - 9-30-15 © 2015 Qorvo - 16 of 16 - Disclaimer: Subject to change without notice www.Qorvo.com
Similar documents
Brochure - Printed Circuit Board Manufacturer
• Annular Ring: .0075 • Finished Trace Width: Inside: .004 Outside: .006 • Spacing Between Traces: Inside: .004 Outside: .006 • SMT Pitch: .012 • Copper to Board Edge: .015...
More information