V-Series Plus User`s Manual
Transcription
V-Series Plus User`s Manual
V-Series Plus User’s Manual Rev. Oct 2009 FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense. EMS AND EMI COMPLIANCE STATEMENT FOR EUROPEAN USERS This equipment has been tested and passed with the requirements relating to electromagnetic compatibility based on the standards EN 55022:1998+A1:2000+A2:2003, CISPR 22 , Class A EN 55024:1998+A1:2001+A2:2003, IEC 61000- 4 Series EN 61000-3-2 / 2000 & EN 61000-3-3 / 1995. The equipment also tested and passed in accordance with the European Standard EN55022 for the both Radiated and Conducted emissions limits. V-SERIES PLUS TO WHICH THIS DECLARATION RELATES IS IN CONFORMITY WITH THE FOLLOWING STANDARDS EN55022 : 1998,CLSPR 22, Class A / EN55024 : 1998IEC 61000-4 Serial / EN61000-3-2 : 2000 / EN 6100-3-3 : 1995 / CFR 47, Part 15/CISPR 22 3rd Edition : 1997, Class A / ANSI C63.4 : 2001 / CNS 13438 / IEC60950-1 : 2001 / GB4943 : 2001 / GB9254 : 1998 / GB17625.1 : 2003 /EN60950-1 : 2001 CAUTION Danger of explosion if battery is replaced incorrectly. Only replace battery with an equivalent type as recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Copyright and Trademark Notice © 2009 by Tharo Systems, Inc. It is illegal to photocopy or electronically transmit a facsimile of this manual or any portion of its contents for any means or purpose without the publisher’s permission. Fines of up to $10,000.00 may be imposed for violation. All brand or product names are trademarks or registered trademarks of their respective companies. Specifications are subject to change without notice. 1 Warranty Information .........................................................................................................................................3 1. Product Description ......................................................................................................................................4 General Information.....................................................................................................................................4 Printer Options ..............................................................................................................................................4 2. General Safety Tips......................................................................................................................................6 3. Unpacking the Printer and Accessories....................................................................................................6 4. Identifying Components ..............................................................................................................................7 5. Printer Setup .................................................................................................................................................9 USB Installation ..........................................................................................................................................10 6. Control Panel ...............................................................................................................................................11 General Description and Operation.........................................................................................................11 Interpreting LED Messages.......................................................................................................................11 Printer Setup................................................................................................................................................11 Auto Sensing................................................................................................................................................12 Turning the See-through Sensor on/off ................................................................................................12 7. Loading Media .............................................................................................................................................13 Ribbon Installation .....................................................................................................................................13 Label Installation ........................................................................................................................................15 Label Roll Core Installation Instructions................................................................................................16 Direct Thermal / Thermal Transfer Mode Switch.................................................................................17 Card / Hang tags Installation...................................................................................................................17 8. Installing the Printer’s Optional Accessories.........................................................................................18 V-Series Stripper Sensor Module Installation Instructions................................................................18 Cutter Module Installation Instructions .................................................................................................21 Compact FLASH Card Slot module with Real-Time Clock ..................................................................23 Appendix A. Communication Interfaces .....................................................................................................24 Parallel Interface.........................................................................................................................................24 Serial Interface ...........................................................................................................................................24 USB Interface ..............................................................................................................................................24 Appendix B. Error Messages / Troubleshooting ........................................................................................25 Self Test........................................................................................................................................................25 Dump Mode..................................................................................................................................................25 LED Error Message Descriptions..............................................................................................................26 Problems and Recommended Solutions.................................................................................................27 Appendix C. Maintenance and Adjustment ................................................................................................28 Cleaning the Thermal Printhead ..............................................................................................................28 Thermal Printhead Print Line Adjustment .............................................................................................29 Thermal Printhead Spring Box Pressure Adjustment..........................................................................29 Thermal Printhead Replacement .............................................................................................................30 Upgrading the Printer’s Firmware ...........................................................................................................31 Downloading True Type Fonts to the Printer’s Flash Memory ..........................................................32 Clearing Cutter Jams .................................................................................................................................33 Cleaning Adhesive from the Cutter Blade .............................................................................................33 2 Warranty Information The THARO V-Series Plus Printers are warranted against defects in material or workmanship for 12 months (365 days) from the date of original shipment by THARO SYSTEMS, INCORPORATED. This warranty does not cover normal wear and tear and shall be null and void if the equipment is modified, improperly installed or used, damaged by accident or neglect, or in the event any parts are improperly installed or replaced by the user. Since Printhead wear is part of normal operations, a Printhead warranty of 3 months (90 days) from the date of original shipment by THARO SYSTEMS, or 25,000 linear meters of use, whichever comes first. To qualify for this warranty, the Printhead must be returned to THARO or another authorized service center. Although the user is not required to purchase THARO brand supplies (media and/or ribbons), to the extent it is determined that the use of other supplies (media and/or ribbons) shall have caused any defect in the thermal Printhead for which a warranty claim is made, the user shall be responsible for THARO's customary charges for labor and materials to repair such defect. To the extent that it is determined that failure to follow the preventive maintenance schedule and procedures listed in the User Guide shall have caused any defect in the thermal Printhead for which a warranty claim is made, this limited warranty shall be void. Any Printhead returned to THARO with scratches or abrasions on the Printhead at the point of failure will be deemed abused and no warranty replacement will be provided. THARO SYSTEMS' SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE TO FURNISH PARTS AND LABOR FOR THE REPAIR OR REPLACEMENT OF PRODUCTS FOUND TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP DURING THE WARRANTY PERIOD. As a condition of this warranty, the user must: (a) obtain a THARO Return Authorization for the Printer, or subassembly(s); (b) ship the Printer or subassembly(s), transportation prepaid to the authorized service location; and (c) include with the Product or subassembly(s) a written description of the claimed defect. Unless THARO SYSTEMS authorizes return of the entire Product, the user shall return only the subassembly(s). Products returned shall be packaged in the original packing and shipping container or comparable container. In the event equipment is not so packaged or if shipping damage is evident, it will not be accepted for service under warranty. Surface transportation charges for the return of the Printer to the customer shall be paid by THARO SYSTEMS within the 48 contiguous states and the District of Columbia. Customer shall pay shipping costs, customs clearance, and other related charges outside the designated area. If THARO SYSTEMS determines that the Product returned to it for warranty service or replacement is not defective as herein defined, BUYER shall be subject to a minimal labor charge and all costs of handling and transportation. Warranty Exclusions and Conditions The above warranties are in lieu of all other warranties, expressed or implied, oral or written, statutory or otherwise, including any implied warranty of merchant-ability or fitness for a particular purpose. THARO SYSTEMS shall not be responsible for the specific application to which any Products are applied, including but not limited to compatibility with other equipment. All statements, technical information and recommendations relating to THARO Products are based upon tests believed to be reliable but do not constitute a guarantee or warranty. THARO SYSTEMS SHALL NOT, UNDER ANY CIRCUMSTANCES WHATSOEVER, BE LIABLE TO BUYER OR ANY OTHER PARTY FOR LOST PROFITS, DIMINUTION OF GOODWILL OR ANY OTHER SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER WITH RESPECT TO ANY CLAIM HEREUNDER. IN ADDITION, THARO SYSTEMS' LIABILITY FOR WARRANTY CLAIMS SHALL NOT, IN ANY EVENT, EXCEED THE INVOICE PRICE OF THE PRODUCT CLAIMED DEFECTIVE, NOR SHALL THARO SYSTEMS BE LIABLE FOR DELAYS IN REPLACEMENT OR REPAIR OF PRODUCTS No salesperson, representative or agent of THARO SYSTEMS is authorized to make any guarantee, warranty, or representation in addition to the foregoing warranty. NO WAIVER, ALTERATION, ADDITION, OR MODIFICATION OF THE FOREGOING WARRANTIES SHALL BE VALID UNLESS MADE IN WRITING AND SIGNED BY AN EXECUTIVE OFFICER OF THARO SYSTEMS. 3 1. Product Description General Information The THARO V-424 Plus and V-434 Plus Printers are Thermal Transfer/Direct Thermal label Printers designed for use on a desktop. The compact V-424 Plus and V-434 Plus feature a small footprint to fit your work environment. The V-Series Plus Printers are constructed of a durable, impact-resistant composite with a media window for easy viewing and monitoring of remaining supplies. The THARO V-424 Plus features a printhead density of 8 dots/mm (203 dots/in) and a maximum print length of 1727mm (68”). The THARO V-434 Plus features a printhead density of 12 dots/mm (300 dots/in) and a maximum print length of 762mm (30”). The THARO V-424 Plus and V-434 Plus Printers provide 125mm (4.92”) diameter label roll and 300 meter length ribbon capacities giving you the benefit of less downtime and increased production. Both Printers come standard with built-in USB for high-speed data transfer from your PC. Accessories available for the THARO V-424 Plus and V-434 Plus Printers include a Cutter for ticket or receipt printing applications, an internal Ethernet Card for network connectivity, a Compact FLASH Card Slot module with a Real-Time Clock for time and date stamping of labels and a Stripper Sensor Module so the Printers can be used in strip-and-peel applications. Printer Options Stripper Sensor Module The Stripper Sensor Module is used to sense printed labels in strip-and-peel applications. With the Stripper Sensor Module installed, the printed labels are presented for removal and the used liner feeds from the Printer and collects on the floor. Cutter The optional Cutter can be used to cut labels or tag stock up to a 10-mil (.254mm) thickness. Cutter options include a choice of: cut after each label, cut after a specific quantity of labels, or cut at the end of a print job. Compact FLASH Card Slot module with Real-Time Clock The Printer has the ability to use internal Flash memory for storing downloaded files including graphics and fonts. This option provides a slot which allows you to install a Compact FLASH card to be used as additional FLASH memory above and beyond the 4MB of FLASH that is standard in the Printer. This increases the available space for the storage of these files. The Printer supports Compact FLASH Cards from 128MB to 1GB. This module also includes a Real-Time Clock for the Time and Date stamping of your labels. Internal Ethernet Adapter Card The Internal Ethernet Adapter Card provides networking capability to the V-424 Plus and V-434 Plus. External Label Stand The External Label Stand allows the use of label rolls with an outside diameter of 203.2 (8”). EASYLABEL® - Label Design Software for Windows EASYLABEL® labeling software allows you to drive your Printer and create a full range of label formats with a minimum of effort. EASYLABEL can be installed under Microsoft Windows® on IBM PCs and compatibles. For further information about EASYLABEL, please contact your THARO Reseller. 4 Technical Specifications Model - Specifications are subject to change without notice. V-424 Plus V-434 Plus Resolution Print Mode CPU Memory Print Speed Print Length Max Print Width Sensor Type 203 dpi (8 dot/mm) 300 dpi (12 dot/mm) Thermal Transfer / Direct Thermal 32 Bit 4MB Flash, 8MB SDRAM 50.8mm (2”) ~ 101.6mm (4”)/sec 12mm (0.47”) ~ 1727mm (68”) 12mm (0.47”) ~ 762mm (30”) 108mm (4.25”) 105.7mm (4.16”) Moveable Reflective sensor; Fixed transmissive; center aligned Type: Label gap and black mark sensing Sensor Detection Detection: Label length auto sensing and/or program command setting Label Roll: Max. 125mm (4.92”) Core Diameter: 25.4mm (1”), 38.1mm (1.5”), 76.2mm (3”) Media Width: 25.4mm (1”) ~ 118mm (4.64”) Thickness: 0.06mm (0.002”) ~ 0.25mm (0.009”) Length: 300m (981’) Type: Ink outside thermal transfer ribbons (wax, resin and wax/resin) in Ribbon widths of 30 to 110mm (1.88” to 4.33”). Core inner diameter 25.4mm (1”). Maximum ribbon roll diameter 68mm (2.67”). Printer Language TPL (Tharo Programming Language) EASYLABEL® Start Software Microsoft Windows Drivers, CUPS (Common UNIX Printing System) Driver 11 resident alphanumeric fonts (including OCR A & B), are expandable Resident Fonts eight times horizontally and vertically. Scalable Font (Code Page 850 & 852) Downloadable Fonts Windows Bit-map fonts, TrueType fonts and Asian fonts Image Handling BMP and PCX Code 39, Code 93, Code 128 (subsets A, B, C), UCC/EAN-128, UPC-A, UPC-E, UPC and EAN 2 or 5 digit extensions, I 2 of 5, EAN-8, EAN-13, Bar Codes Codabar, Postnet, DUN 14, MaxiCode, Plessey, Telepen, FIM, China Postal Code, RPS 128, PDF417, Data Matrix & QR Code RS-232 Serial (Baud rate 4800 ~ 115200, XON/XOFF, DSR/DTR) Interfaces USB(2.0) Parallel Two Bi-color LEDs: Ready and Status Control Panel Function Key: FEED Power Auto Switching 100/240VAC, 50/60 Hz Operation: 41° F to 104° F (5° C to 40° C) Environment Storage: -4° F to 122° F (-20° C to 50° C) Operation: 30-85%, non-condensing. Free air. Humidity Storage: 10-90%, non-condensing. Free air. Length: 285mm (11.2”) Height: 171mm (6.8”) Printer Dimensions Width: 226mm (8.9”) Weight: 2.72Kg (6.0 lbs) Cutter Stripper Sensor Module Compact FLASH Card Slot module with Real-Time Clock Options Internal Ethernet Adapter External Label Stand EASYLABEL Silver, Gold, Platinum or Multi-User 5 2. General Safety Tips CAUTION! During the print process the Printhead will become hot. Do NOT attempt to clean the Printhead until it has had time to cool. The Printhead is the Most Fragile part of your Printer. Do NOT use sharp or hard objects to clean the Printhead. Do NOT touch the glass surface of the Printhead with your hand. This Printer is built exclusively to print labels, tickets and tags, continuous paper, etc. Only use media that is recommended for a direct thermal or thermal transfer Printer. The Printer is configured for input voltages of 110 to 240 V. Connect only to a power outlet with a grounded contact. Always ensure the Printer is switched OFF before connecting the power cord to an electrical outlet. Do not expose the Printer to moisture or operate it in wet or damp areas. Remove the power cord from the rear of the Printer when disconnecting or attaching accessories such as Stripper Sensors, Cutters, etc. 3. Unpacking the Printer and Accessories Check the condition of the packaging and contents for possible damage during transit. NOTICE: Please retain original boxes and all original packing materials in case the Printer must be returned. In addition to this manual the following items should be included with your Printer: Bar Code Printer Power Cord (110V or 230V) Switching Power Adapter Ribbon Shaft, Qty. 2 Label Roll Core Empty Ribbon Roll Quick Start Guide Accessories CD: Includes Label Software, Manuals, Windows Drivers and CUPS Driver. The following additional items are necessary for generating labels from your Printer: Serial, Parallel, or USB cable Applicable media (label stock/ribbon) 6 4. Identifying Components 1 2 3 5 4 6 7 8 1. 2. 3. 4. 5. 6. 7. 8. Open Cover Button Top Cover Label Roll Core Ribbon Rewind Wheel Print Mechanism Ribbon Rewind Shaft + Empty Take Up Core Head Latches (left/right) Front Cover Panel 4 1 2 3 5 1. 2. 3. 4. 5. LED (Ready) LED (Status) FEED Key Compact FLASH Card Slot Module Cover Printhead Pressure Adjustment Screw (left/right) 7 1 4 2 5 3 1. 2. 3. 4. 5. Ribbon Supply Shaft Label Guide Platen Roller Print Line Adjustment Label Sensor 3 4 5 6 7 1 2 1. 2. 3. 4. 5. 6. 7. Fan-Fold Label Slot Power Switch Ethernet Socket (Option) USB Port Parallel Port Serial Port (RS-232) Power Socket 8 5. Printer Setup CAUTION! When choosing a location for the Printer, ensure that the Printer and operator remain dry. If the Printer or the operator get wet, serious injury to the operator or damage to the Printer may occur. CAUTION! Make sure that the Printer’s power switch is in the “O” or “Off” position before proceeding with the installation. 1. Plug the lead from the Switching Power Adapter into the Printer’s power socket. 2. Plug the supplied power cord into the Switching Power Adapter and then plug the other end of the power cord into a grounded outlet. 3. Select the correct cable for the chosen interface. The Printer can be directly connected to the PC in one of 3 ways: USB, parallel, or serial. For the connection to the USB port use a suitable USB cable. For the connection to the PC’s parallel port use a suitable parallel interface cable. If the serial interface is used make sure the proper serial cable is used. You can find pin assignments and descriptions for all three interfaces connectors in Appendix A. NOTICE! For Serial communications make sure that the Serial Port Settings in the Printer are configured the same as in the software you will be using with the Printer. 4. Connect the Printer to the computer with the selected cable. Then secure the cable using any screws or clips attached to the connectors. These prevent the connection from working loose. 5. Turn the Printer on, the Ready LED will glow green when the Printer is on. 9 USB Installation 1. USB is a Plug & Play facility. Once the USB cable is connected from PC to the Printer, the PC will automatically detect the new device and begin the installation process. 2. Select ‘Specify a location’ and specify the path of the Printer driver. 3. Follow the instructions in the Wizard to complete the installation. Note: These instructions are only for use when using Windows Drivers. When using label software such as EASYLABEL® you can disable the prompting for Windows Drivers. Consult the knowledgebase on our website at www.tharo.com for detailed instructions. 10 6. Control Panel General Description and Operation FEED Key Pressing the FEED key will cause the Printer to advance the media (according to media type) to a specified stop position. If the Printer is loaded with continuous media the Printer will FEED the media out a certain length. If the Printer is loaded with labels with gaps or black marks, the Printer will advance one label at a time. If the label is not sent out in a correct position the sensor must be calibrated. Follow the instructions for Sensor Calibration in the Maintenance and Adjustment section of this manual. Interpreting LED Messages LED Ready Status Green Beep Description 1 Normal The Printer is printing a Self-Test Label. Refer to Appendix B for more information. The Printer is in Dump Mode. Refer to Appendix B for more information. Printer is in Auto-Sensing Mode. Red (Flashing) Orange 3 Green (Flashing) Orange 3 Orange Or Green* Orange Or Green* 3 Red (Flashing) The Printer is in firmware download mode. *If both of READY and STATUS lights are green when doing Auto-Sensing, then the See-through Sensor is on. If both of READY and STATUS lights are orange, then the See-through Sensor is off. Printer Setup By holding down the FEED key and turning the power on, you will be able to change the Printer settings depending on how many times the beeps before the FEED key is released. When the Printer is first powered up, the Printer will beep 3 times quickly, and then will beep slowly after that. Printer Setting Self Test Auto Sensing Dump Mode On Direct Thermal Thermal Transfer See Through Sensor ON Top of Form ON/OFF Slow Beeps 0 beeps 1 beep 2 beeps 3 beeps 4 beeps 5 beeps 6 beeps 11 Auto Sensing Using Auto Sensing the Printer automatically detects and records the label type and length (gap or black mark paper). Then the Printer can accurately detect the label positions. 1. Adjust the Moveable Sensor so that it is located in a position to sense the label gaps or black marks. 2. Turn the Printer Off and press and hold the FEED key. 3. Turn the Printer On while holding down the FEED key. 4. The Printer will beep three times. Then release the FEED key. Continue to hold the FEED key down; the Printer will beep again. 5. The Printer will now detect and record the label size/length. NOTICE! If both of READY and STATUS lights are green when doing Auto-Sensing, then the See-through Sensor is on. If both of READY and STATUS lights are orange, then the See-through Sensor is off. Turning the See-through Sensor on/off There are two types of Media Sensor in V-Series Plus Printers – a Reflective Sensor and a See-through Sensor. By default, the Reflective Sensor is turned on and the See-through Sensor is turned off. The Reflective Sensor may not be able to detect the label gap on labels with thick liner, colored liner, or graphics. In these cases the See-through Sensor would need to be enabled. To turn the See-through Sensor on: 1. Turn the Printer Off and press and hold the FEED key. 2. Turn the Printer On while holding down the FEED key. 3. The Printer will beep three times. Continue to hold the FEED key down; wait for the STATUS light turn red and READY light flash green, then release the FEED key. 4. The Printer will automatically print “SEE-THROUGH SENSOR IS ON”. This indicates that the See-through Sensor is turned on (and the Reflective Sensor is turned off). NOTICE! To turn the See-through Sensor off, repeat above-mentioned procedures. Then the Printer will print “SEE-THROUGH SENSOR IS OFF” to indicate that the See-through Sensor is turned off and the Reflective Sensor is now on. NOTICE! If both of READY and STATUS lights are green when doing Auto-Sensing, then the See-through Sensor is on. If both of READY and STATUS lights are orange, then the See-through Sensor is off. 12 7. Loading Media Ribbon Installation 1. Open the Printer’s Top Cover by pressing the Open Cover Buttons on both sides. 2. Release the Print Mechanism by pushing in on the Head Latches. The Print Mechanism will now rotate up. 3. Remove the Ribbon Supply and Ribbon Rewind Shafts. 4. Place the new Ribbon Roll onto the Ribbon Supply Shaft and reinstall the Shaft in the Printer. 13 5. Feed the ribbon from the Ribbon Supply Shaft under the Printhead. 6. Place the empty ribbon core onto the Ribbon Rewind Shaft and reinstall the Shaft in the Printer. 7. Secure the ribbon to the empty ribbon roll core with tape or part of a label and wrap the ribbon around the core. 8. Close the Print Mechanism by firmly pressing down on it. You will hear a click when the Print Mechanism has been secured. 14 Label Installation 1. Open the Printer’s Top Cover by pressing the Open Cover Buttons on both sides. 2. Place the roll of label stock onto the Label Roll Core and place it in the Printer. 3. Release the Print Mechanism by pushing in on the Head Latches. The Print Mechanism will now rotate up. 4. Feed the label through the two Label Guides to the Tear-off Bar. 5. Align the label guides to the label edge. 6. Close the Print Mechanism by firmly pressing down on it. You will hear a click when the Print Mechanism has been secured. 15 Label Roll Core Installation Instructions 1” Roll Core Installation 1.5” roll core installation 3” roll core installation 16 Direct Thermal / Thermal Transfer Mode Switch To switch into Direct Thermal (DT) Mode: 1. Turn the Printer Off and press and hold the FEED key. 2. Turn the Printer On while holding down the FEED key. 3. The Printer will beep three times. Continue to hold the FEED key down until the Printer beeps three more times. Release the FEED key after the third beep. 4. The Printer will print, “NOW IS DIRECT THERMAL (DT MODE)”. This indicates that Printer is now in DT Mode. To switch into Thermal Transfer (TT) Mode: 2. Turn the Printer Off and press and hold the FEED key. 3. Turn the Printer On while holding down the FEED key. 4. The Printer will beep three times. Continue to hold the FEED key down until the Printer beeps four more times. Release the FEED Key after the fourth beep. 5. The Printer will print, "NOW IS THERMAL TRANSFER (TT MODE)". This indicates that Printer is now in TT Mode. Card / Hang tags Installation When installing card tags, the tag hole must align with the sensor arrow (as indicated), and then use the Label Guide to secure the tags. Tag hole position Sensor Detection Position Sensor 17 8. Installing the Printer’s Optional Accessories The Optional Stripper Sensor Module, Cutter Module, or Compact FLASH Card Slot module with Real-Time Clock can be easily installed and configured in the field. This section will provide a component list and installation instructions for these optional accessories. CAUTION! Make sure that the Printer’s power switch is in the “O” or “Off” position before proceeding with the installation. CAUTION! Unplug the power cord from the Printer before performing any service on it. Failure to do so could result in personal injury or damage to the Printer! V-Series Stripper Sensor Module Installation Instructions 1 2 Stripper Sensor Module Screws, Qty. 2 NOTE: The max width when using the Stripper Sensor Module is 110mm 1 NOTE: Recommended Label liner thickness when using the Stripper Sensor Module is 0.06mm ± 10% with basic weight 65g/ ± 6%. 1. Open the Printer’s top cover by pressing the Open Cover Buttons on both sides. 2 ㎡ 2. Release the Print Mechanism by pushing in on the Head Latches. The Print Mechanism will now rotate up. 18 3. The Front Cover Panel has two tabs, one on each side. Push these in to release them and then remove the Front Cover Panel as shown. 4. To the right you will see two sockets. Choose the socket that has the same number of pins as the connector on the Stripper Sensor Module. Plug the connector into that socket. 5. Position the Stripper Sensor Module as shown. 6. Hold the Stripper Sensor Module while tightening the screws. 19 7. Peel off the first label and feed the liner through the roller and peel off bracket. 8. Route the label liner as shown. 9. Close the Stripper Sensor Module by pushing it forward as shown. 10. Close the Print Mechanism by firmly pressing down on it. You will hear a click when the Print Mechanism has been secured. Then press the FEED Key. 20 Cutter Module Installation Instructions 1 2 Cutter Module Screws, Qty. 2 1 2 1. Open the Printer’s top cover by pressing the Open Cover Buttons on both sides. 2. Release the Print Mechanism by pushing in on the Head Latches. The Print Mechanism will now rotate up. 3. The Front Cover Panel has two tabs, one on each side. Push these in to release them and then remove the Front Cover Panel as shown. 4. To the right you will see two sockets. Choose the socket that has the same number of pins as the connector on the Cutter Module. Plug the connector into that socket. 21 5. Position the Cutter as shown. 6. Pull up on the Cutter’s Stainless Cover to release the Cutter and then flip the Cutter Module open. 7. Hold the Cutter Module while tightening the screws. 8. Pull on the Cutter’s Stainless Cover to release the Cutter and then rotate the Cutter back into place. 9. Close the Print Mechanism by firmly pressing down on it. You will hear a click when the Print Mechanism has been secured. 22 Compact FLASH Card Slot module with Real-Time Clock 1 2 Card Slot Module (Front View) Card Slot Module (Back View) 2 1 1. Open the Printer’s top cover by pressing the Open Cover Buttons on both sides. 2. Remove the Label Roll Core. 3. Remove the Card Slot Module Cover. 4. Carefully line up the connectors and then plug the Card Slot Module into the Mainboard. 5. Replace the Card Slot Module Cover. 23 Appendix A. Communication Interfaces Parallel Interface The Printers are equipped with a 36-pin Parallel interface connector. Any standard IBM PC compatible parallel cable can be used to connect to your Printer. In the event of any difficulties, the table listed below can be used to obtain a suitable cable. PIN NO. 1 2-9 10 11 12 13 14 15 16 17 18 19-30 31 32 33 34-35 36 FUNCTION Strobe Data 0-7 Acknowledge Busy Paper Empty Select Auto-Linefeed N/C Signal Ground Chassis Ground +5V DC Signal Ground Initialize Fault Signal Ground N/C Select-in TRANSMITTER Host / Printer Host Printer Printer Printer Printer Host / Printer Host Host / Printer Printer Host / Printer Serial Interface The Printers are equipped with a 9-pin SUB-D connector to be used as a Serial interface. NOTICE! Make sure that the “COM Port Setup Options” in the Printer’s front panel are configured the same as the software you will be using with the Printer. Connector Type: DB9 female, pin assignment is as follows: PIN NO. FUNCTION 1 2 +5 V TXD 3 4 5 RXD N/C GND *Flow Control Line 6 7 8* 9 N/C CTS RTS N/C Serial interface from PC to Printer PC --RXD TXD DTR GND DSR RTS CTS --- Printer 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 +5V TXD RXD N/C GND N/C CTS RTS N/C USB Interface The Printer is equipped with a Type B USB connector that can be connected to any compatible USB port. PIN NO. FUNCTION 1 2 3 4 USBVCC D- D+ GND 24 Appendix B. Error Messages / Troubleshooting Self Test The Printer’s Self Test function prints a Test Label that consists of a test pattern and a variety of information about how the Printer is configured as well as its status. To 1. 2. 3. 4. perform a Self Test: Turn the Printer Off. Press and hold the FEED key. Turn the Printer On while still holding the FEED key down. Release the FEED key after hearing 3 beeps. After about 1 second the Printer will print the Test Label. This means the Printer is operating normally. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. V-434Plus : X.XXX Serial port :96,N,8,1 int-usb sw setting : ext-USB 1 DRAM installed Image buffer size : 1500K 000 FORM(S) IN MEMORY 000 GRAPHIC (S) IN MEMORY 000 FONT(S) IN MEMORY 000 ASIAN FONT(S) IN MEMORY 000 DATABASE(S) IN MEMORY 2048K BYTES FREE MEMORY ^S4 ^H10 ^R000 ~R200 ^W101 ^L76,3 Option : ^D0 ^O0 ^AT See-through Volt: 4.8 3.4 1.4(3.4) Code Page: 850 13. 14. 15. 16. Model & Firmware Version Serial port settings USB/Ethernet switch status Number of DRAM installed Image buffer size Number of forms Number of graphics Number of fonts Number of Asian fonts Number of Databases Free memory size Speed, Heat, Reference Point, Print Direction. Label Width, Label Length, Gap Length Cutter, Stripper Mode See-through Sensor Status Code Page Dump Mode The Printer’s Dump Mode provides the ability to print the command sequences received by the Printer instead of executing them. Dump Mode is very useful as a troubleshooting tool when the label settings and the print results do not match, and can be used to check for errors in data transmission between the Printer and the PC. Examining the Dump Mode print out will confirm whether or not the correct commands were received. To enter Dump Mode: 1. Turn the Printer Off. 2. Press and hold the FEED key. 3. Turn the Printer On while still holding the FEED key down. 4. The Printer will beep three times. Continue to hold the FEED key down; the Printer will beep again. Continue to hold the FEED key down; the Printer will beep one more time. 5. Release the FEED Key after the last beep. The Printer will print “DUMP MODE BEGIN”. The Ready LED will glow Green and the Status LED will glow Orange to show that the Printer is in Dump Mode. 6. Send commands to the Printer and check to see if the commands printed are the same commands sent by your application. 7. Press the FEED key to exit Dump Mode. The Printer will print “OUT OF DUMP MODE” and beep to confirm that it is no longer in Dump Mode. 25 LED Error Message Descriptions Condition or Message Print head is open Entering the Cooling Process LEDs Ready Status Red Red Red (Flash) (Flash) Beeps 4 None Out of ribbon or check Ribbon Sensor Red 3 Out of media or check media gap sensor Red 2 Description Re-open print head and make sure it closes tightly. Printhead temperature is too Printer will go back into high. Standby Mode after cooling. No Ribbon is installed, and the Make sure the Printer is in Printer shows error message. Direct Thermal mode. The ribbon is used up or Ribbon Supply Shaft is not Replace with new ribbon roll. moving. Make sure the movable sensor is at the correct position. If The Printer is unable to detect the sensor is still unable to label stock. detect labels then go through the Auto Sensing steps again. Printhead not firmly in place. The label stock is used up. Check paper setting Red 2 Command is not recognized Red 2 Memory is full Red 2 Filename can not be found Red 2 Filename is repeated Red 2 Solution Replace with new label roll. Possible causes: 1. Media falling into the gap behind the platen roller. Improper paper feed. 2. Can’t find the label gap/ black mark. 3. Black mark paper out. Wrong command; the Printer Check Printer commands, prints out “Command is not possible errors or missing recognized”. parameters. Delete unnecessary data in Memory is full; the Printer the memory or add the prints out “Memory full”. optional memory expansion module. Use “~X4” command to print Can’t find the file; the Printer out all the files and check prints out “Filename can not whether the file exists and the be found”. name is correct. File name is repeated; the Change the file name and Printer prints out “Filename is download again. repeated”. NOTICE! The Printer repeats all warning beeps. For example when the Printer’s Printhead Mechanism is opened, the Printer will beep four times, pause, and then beep four more times. 26 Problems and Recommended Solutions Problem LED does not light after switching the Printer on LED turns red (power/status) after printing stops Printing started but nothing was printed on the label The labels jammed when printing Only part of the label was printed Part of the label was not printed completely Printout not in desired position Labels are skipped while printing Smudged or blurry printout The Cutter did not cut straight The Cutter did not cut the label successfully When using the Cutter the labels could not feed or abnormal cutting occurs The Stripper Sensor is not functioning correctly Recommended Solution Check the power cord Check for software setting or program command errors Check if labels or ribbon is out and replace with suitable labels or ribbon Check if label stock is jammed Check if Printhead Mechanism is closed (Printhead not positioned correctly) Check if sensor is blocked by paper/label If cutter is installed check that it is working and working properly Check that the ribbon is installed with the inked side facing the label media. Select the correct Printer driver Select the correct label stock and print mode Clear the label jam and check that the Printhead is clean Check if label or ribbon is stuck on the Printhead Check if application software has errors Check if start position setting has errors Check if ribbon has wrinkles Check if Ribbon Supply Shaft is creating friction with the platen roller. If the platen roller needs to be replaced, please contact your Reseller for more information. Check if power supply is within the voltage range Check if Printhead is dirty Use internal command “~T” to perform a Test Print and check if the Printhead can print across its entire width Check the media quality Check if sensor is covered by paper or is dirty Check if liner is suitable for use, please contact Reseller for more information Check if label roll edge is aligned with Label Width Guide Check if error occurs on label height setting Check if the sensor is covered by paper or is dirty Check print darkness setting Check if Printhead is dirty Check if label stock is installed correctly Check if the label thickness exceeds 0.16mm (.006”) Check if Cutter is installed properly Check if Paper Feed Rods are sticky Check that label is greater than 35mm (1.38”) high so it can clear the Cutter Check if Stripper Sensor is covered with dust Check if labels are installed properly 27 Appendix C. Maintenance and Adjustment Cleaning the Thermal Printhead CAUTION! The Printhead is the Most Fragile part of your Printer. Do NOT use sharp or hard objects to clean the Printhead. Do NOT touch the glass surface of the Printhead with your hand. CAUTION! During the print process the Printhead will become hot. Do NOT attempt to clean the Printhead until it has had time to cool. Printing labels will cause dirt such as paper dust, particles of ink and label adhesive to accumulate on the Thermal Printhead. This can cause poor print quality and incomplete printouts. When this happens the Printhead must be cleaned: 1. Turn the Printer Off. 2. Open the top cover. 3. Release the Print Mechanism by pushing in on the Head Latches. The Print Mechanism will now rotate up. 4. Remove the ribbon from the Printer. 5. Clean the Printhead surface (see blue arrow) with a special cleaning pen or a cotton swab soaked in Isopropyl Alcohol. 6. Allow the Printhead to dry for 2-3 minutes before turning the Printer back on. NOTICE! To help keep the Printhead clean the top cover of the Printer should be closed when printing. To ensure print quality and prolong Printhead life, do NOT use dusty or dirty print media in the Printer. NOTICE! Recommended cleaning intervals for the Thermal Printhead: Direct Thermal Printing – Each time the label roll is changed Thermal Transfer Printing – Each time the ribbon is changed 28 Thermal Printhead Print Line Adjustment When printing on stiff or thick paper, the Print Line needs to be moved forward (paper feed direction) in order to achieve better print quality. 1. Release the Print Mechanism by pushing in on the Head Latches. The Print Mechanism will now rotate up. 2. Turning the Print Line Adjustment counterclockwise (as arrow 1 shows) will move the Printhead in the direction of arrow A. A 3. Turning the Print Line Adjustment clockwise (as arrow 2 shows) will move the Printhead in the direction of arrow B. 1 2 B Thermal Printhead Spring Box Pressure Adjustment If one side of the printed labels is not being printed clearly, or if ribbon wrinkles occur, then adjust the Thermal Printhead Spring Box Pressure to cure the problem. 1. Open the Top Cover. 2. Remove the Thermal Transfer Ribbon. 3. Turn the Printhead Adjustment Screws to increase or decrease the Printhead pressure. + 29 - + - Thermal Printhead Replacement 1. Switch the power to the Printer off and unplug the Printer. 2. Open the Printhead and remove the media from the Printer. 3. Remove the Printhead Carriage Screw as shown. 4. Once the Printhead Carriage Screw is removed, the Printhead Carriage will drop down and provide access to the Printhead Screws. 5. Remove the two Printhead Screws 6. Remove the plastic Printhead Guard from beneath the Printhead and the Printhead will hang from the Carriage by the Printhead Cable 7. Gently unplug the Printhead Cable from the Printhead. 8. Reverse these steps to re-install the Printhead. 30 Upgrading the Printer’s Firmware The Printer’s firmware can be upgraded in the field by performing the following procedure: 1. Connect the Printer to a computer. 2. Unzip the firmware files and save them to a directory on your computer. 3. Start the Download Tool program by double clicking on DownloadTool.exe . 4. Select the port that is being used to communicate with the Printer and click the “Download Firmware” button. If downloading via the serial port the baud rate MUST be set to 115200 in the Printer. 5. This will bring up a Browse Window displaying the firmware (.bin) files that can to be loaded to the Printer. Select the appropriate firmware file and click “Open”. 6. After the “Open” button is clicked, the firmware download process will start immediately. A blue progress bar will pop up to display the progress of download. 7. When the progress bar reaches “100%”, the firmware download is complete. As the download finishes, the Ribbon and Media light will alternately flash slowly and then rapidly. 8. The Printer will now reset, please wait for Printer to complete the reset procedure. The Printer will return to “Ready to print” status after the reset. 9. The new firmware version will be displayed on the Printer’s LCD. This confirms that the firmware has been updated. 31 Downloading True Type Fonts to the Printer’s Flash Memory 1. Start the Download Tool program by double clicking on DownloadTool.exe . 2. Select a ‘Font Number’ that will be used to identify the downloaded True Type Font. 3. Click the “Download True Type Font” button, the program would show a list of True Type Fonts that are available for download. Select a True Type Font and click “OK”. 4. After the “Open” button is clicked, the download process will start immediately. A blue progress bar will pop up to display the progress of download. 5. When the progress bar reaches “100%”, the True Type Font download is complete and the True Type Font is stored in the Printer’s Flash memory. 32 Clearing Cutter Jams 1. If the Cutter jams or malfunctions turn the Printer Off. 2. There is a hole (marked “A”) on each side of the Cutter. Insert a 3mm hex key into one of these holes and turn the cutter blade clockwise. A 3. After the problem is corrected, turn the Printer back On and the cutter blade will go back to its original position. Note: It is recommended to use labels greater than 35mm (1.38”) in height in order for them to clear the Cutter. Cleaning Adhesive from the Cutter Blade When using adhesive labels, the cutter may malfunction due to a build up of adhesive on the blade. When this happens it will be necessary to clean the Cutter Blade: 1. Turn the Printer Off. 2. Remove the Cutter assembly from the Printer. 3. Wet a cotton swab in Isopropyl Alcohol and use it to remove any build-ups of adhesive. 4. There is a hole (marked “A”) on each side of the Cutter. Insert a 3mm hex key into one of these holes and turn the cutter blade clockwise to allow access to the entire length of the blade. 5. Allow the cutter to dry for 10 minutes. 6. Re-install the Cutter assembly and turn the Printer back On. The cutter blade will go back to its original position. 33