Crestline® Altra SeriesTM Dampener Installation Instructions

®
Crestline Altra Series Dampener
TM
Installation Instructions
Ryobi 3302M
Itek 3985
A.B. Dick 9985
X88-67
7/98
Rev-A
GENERAL INFORMATION
ATTENTION
CRESTLINE®
ALTRATM SERIES
DAMPENER
OWNER!
Accel Graphic Systems provides parts and service through its
authorized distributors and dealers. Therefore, all requests for
parts and service should be directed to your local dealer.
The philosophy of Accel Graphic Systems is to continually improve
all of its products. Written notices of changes and improvements
are sent to Accel Graphic Systems' Dealers.
If the operating characteristics or the appearance of your product
differs from those described in this manual, please contact your
local Accel Graphic Systems Dealer for updated information and
assistance.
Always update your dampener when improvements are made
available, especially those related to safety.
YOUR AUTHORIZED CRESTLINE® ALTRATM SERIES
DEALER IS:
THE SERIAL NUMBER OF YOUR CRESTLINE®
ALTRATM SERIES DAMPENER(S) IS:
SAFETY
INFORMATION
2
FOR YOUR SAFETY, DO NOT DISENGAGE OR REMOVE ANY
GUARDS FROM THE CRESTLINE ® ALTRA TM SERIES
DAMPENER. THE DAMPENER CONTAINS SOME INWARD
ROTATING ROLLER NIPS THAT CAN CAUSE INJURY IF LEFT
UNGUARDED.
GENERAL INFORMATION
C 3/16" (5mm)
BASIC
CONFIGURATION
OF CRESTLINE®
ALTRATM SERIES
B 5/32" (4mm)
A 5/32" (4mm)
M
I
P
O
D 5/32" (4mm)
F
E 5/32" (4mm)
Plate
Cylinder
Adjustments
A. Intermediate to Oscillator
B. Metering to Intermediate
C. Metering to Pan
D. Oscillator to Form
E. Form to Plate
TERMINOLOGY
TECHNICAL
ASSISTANCE
Roller Description
P = Pan
M = Metering
I
= Intermediate
O = Oscillator
F = Form
OPS
=
Operator's Side
NOPS
=
Non Operator's Side
For technical assistance during the installation, please contact:
ACCEL GRAPHIC SYSTEMS
11103 Indian Trail
Dallas, TX 75229
PHONE (972) 484-6808
FAX (800) 365-6510
E-MAIL [email protected]
WEB SITE www.accelgraphicsystems.com
Crestline® AltraTM Series is covered by U.S. Patents Pending
3
GENERAL INFORMATION
REQUIRED TOOLS
4
1.
Phillips Screwdriver
2.
Standard Screwdriver
3.
1/8" & 3/32" Allen
4.
2.5, 3, 4, 5, & 6 mm Allens
5.
8, 10, 13, & 17 mm Wrenches
6.
7/16" Open End Wrench
7.
Vise Grips
8.
4 mm Punch
9.
Brass Drift
10.
1/8" Punch
11.
Hammer
PRE-INSTALLATION INSTRUCTIONS
PRE-INSTALLATION PROCEDURES AND
HOW TO PARALLEL THE DAMPENER.
1. Cut the ties holding the rollers and examine the rollers for
gouges, scratches or nicks.
2. Check the box and parts boards to make sure all pieces are
present and nothing has been damaged in shipment.
3. Check the dampener alignment by setting it on end on a flat
surface such as a cutter bed. If dampener rocks, it needs to be
realigned. Loosen the tie bar bolt and align the frames on the
flat surface. Retighten bolt.
5
6
DISASSEMBLY
1
2
3
Disconnect the press from the power supply. Remove inker guards
on both printing units. Remove operating handles and upper side
covers from OPS & NOPS sides of both printing heads. Remove the
small covers over the water control mechanism OPS & NOPS. On
older model presses, remove the gray plate that indicates the clicks
in ratchet system. Remove the water tray and cloth covered rollers
from both printing units.
At the OPS, remove "E" clips and washers (subject arrows) from
stud and pull off the assembly held by these parts.
At the OPS, remove the spring behind the arm (large subject arrow,
not visible in picture). Remove the "E" clips and washers (subject
arrows) and pull the assembly off.
7
8
DISASSEMBLY
4
5
6
At the OPS, remove the spring (#1), housing with clutch (#2), and
infinite water control (#3, held on by 4 bolts) from the end of the
water fountain roller shaft. (Older models have an arm and ratchet
assembly with a gear. Remove these pieces if the press does not
have the infinite water control. The gear has a set screw in it that
needs to be loosened before you can remove it.)
Drive the pin out of the arm (large subject arrow) and remove it.
Remove all the screws indicated by the subject arrows. The arrows
on the left indicate the housings for the metal rollers and ductor. The
upper arrow, on the right, is the water pan block. These are at the
OPS.
Remove the bolt from the wiper bar (upper subject arrow). These
are located at the OPS. (On older models, the bolt holding the wiper
bar is at the NOPS.) Remove the wiper bar.
OPTION: You can remove the small screw and clicker plate from the
water form adjustment screw block (lower subject arrow) and
replace it with the set screws #05-153025 provided by Accel. This
will secure the form to plate setting once adjusted.
NOTE: This picture has the parts already removed.
9
10
DISASSEMBLY
7
Unhook the wires from the solenoid at NOPS (subject arrow) and
remove the it from the press. 3 screws hold the solenoid. Each
screw has a washer and a spacer. Be sure these parts do not fall
in the press.
8
At the NOPS, drive the pin out and remove the arm (subject arrow
at far right.) Remove the screws near the other subject arrows
9
Remove the nut and spool from the end of the oscillator (subject
arrow.) The easiest way to do this is:
1. Rotate the press, by hand, until the oscillator has moved all the
way to the NOPS.
2. Remove the nut and lock washer from the end of the oscillator.
Save for reinstallation.
3. Remove the oscillator bushing at the OPS and slide the
oscillator roller by hand to the OPS. The spool will come off.
Save all of the parts for reinstallation.
11
12
DISASSEMBLY
10
11
Inspect cam follower for wear. If there is a substantial amount of
wear, it should be replaced before installation of new oscillator
roller.
Remove the cap screw (subject arrow) holding the two pieces of the
water fountain roller together. Remove the bushings from the side
frame holding the roller, slide the two pieces apart, and remove the
pan roller and extension from the press.
NOTE: Older models may have a single piece fountain roller.
12
Remove the 2 screws and bushing (subject arrow) for the oscillator
at the NOPS. Save for reinstallation. Slide the oscillator roller out of
the press.
13
14
DISASSEMBLY
13
14
15
The water ductor mechanism (subject arrow) has a series of set
screws holding it to the shaft. Loosen all the set screws, including
the one in the brass collar in the middle. Remove the bushings
holding the shaft in the side frames. Gently tap the shaft towards the
OPS until it clears the inside of the press frame. The entire
assembly can be removed.
Remove the bolt and spring loaded arm (subject arrow) at OPS &
NOPS.
Remove the studs (subject arrow ) from inside the press frame.
YOU ARE NOW READY TO INSTALL CRESTLINE® ALTRATM
SERIES
15
16
INSTALLATION
1
Install the new form oscillator roller (X07-0431) provided by Accel.
The easiest way to accomplish this is by following this order:
1. Place the roller in position with the gear on the NOPS.
2. Install the NOPS bushing that was previously removed.
3. Hold spool in position and slide the shaft all the way through the
spool.
4. Install the OPS bushing assembly.
5. Install the jam nut and lock washer on the NOPS end of the
oscillator shaft and fully tighten.
2
3
Install the stripe adjustment blocks (X10-36 & X10-35) provided.
These have an OPS & NOPS side. When installed, it needs to be
positioned so that the flat surface is facing up and level.
Install OPS & NOPS mounting plate. Use the large spools (X12-28)
and cap head bolts & washers (X05-114138 & 05-313328) provided. On OPS, if there is a notched out cavity (large subject arrow)
then use the spool (X12-27) with the flat portion facing towards the
bottom. After mounting the spool use the second mounting bolt
(X05-123113). Only one bolt is used per side.
NOTE: Remove the caps from the mounting block after installation. The center adjustment bolt is pre-set at the factory and
should not need to be adjusted.
17
18
INSTALLATION
INSTALLATION
4
5
6
Temporarily reconnect press to power supply. Make sure any loose
parts or tools are clear for operation. Jog press and observe mesh
between the gear on the oscillator roller and the mounting gear on
the NOPS mounting plate. A whining sound generally indicates that
the gear mesh is too loose. A grinding sound indicates that the gear
mesh is too tight. Adjust if necessary by loosening plate mounting
bolts, repositioning and then retightening.
Install lift shaft (X15-18) into press with the longest portion that
extends past cams to the NOPS (left hand picture). At OPS &
NOPS, install the lift shaft housings (X99-17) with the notched
portion aligned with the mounting hole (right hand picture). Use the
cap head bolts (X05-127M12) and washers (X05-313442) provided to secure the housings to the frame.
At OPS & NOPS, slip the thin brass washer (X05-315630) and then
the set collar (X13-5038) over the end of the lift shaft. Position shaft
so that the end if flush with the set collar on OPS. Finger tighten only
at this time.
19
20
INSTALLATION
7
8
9
Place the dampener in the press as shown. The ball bearings on the
end of the pan roller shaft should sit in the notches of the mounting
plates. Position the dampener evenly, side to side. Install the caps
of the mounting brackets with the cap head bolts provided. Adjust
nylon screws (X05-118M25P) on the side of the dampener frame
until they contact the mounting plate without binding the dampener
and lock into position with the nylon nut (X05-218P).
Observe the position of the cams on the lift shaft. These cams
should line up with the ball bearings on the dampener and not touch
the dampener frames. If the cams are not centered then loosen the
set collars and center. Fully tighten the set collars at this time.
Install the extension springs (X09-0102) on the OPS & NOPS. It
connects on the spring stud on the dampener and the spring stud
on the stripe adjustment blocks installed in step #2.
21
22
INSTALLATION
10
Slip the control block (X17-0303) over the end of the lift shaft (left
hand picture) but do not tighten the set screws at this time. With the
2 button head screws (X05-134025) (upper subject arrow) just
threaded into the lower clamp block (X17-0108), slip the block over
the activation linkage (lower subject arrow). It is grooved to clamp
over the link (as shown). Push the lower clamp block down until it
stops against the bend in the link and fully tighten the button head
screws.
NOTE: Picture is shown with additional parts removed for
viewing. It is not necessary to remove these parts in the
installation.
11
12
Install the activation link (X17-0505) (upper subject arrow) provided by Accel. The link is mounted with a cap head bolt (05173125) on top and bottom. However, the slotted portion (lower
subject arrow) of the link should be in the lower mounting hole.
Temporarily replace the single lever. Run the set screws on top of
the dampener up until they no longer touch the blocks in the water
on position.
23
24
INSTALLATION
13
With the single lever in the "WATER ON" position, rotate the lift shaft
up until it contacts the lift cams on the dampener. Rotate the control
block (upper subject arrow) clockwise so that the activation link
(lower subject arrow) is topped out in the lower slot. Tighten the set
screws in the control block in this position making sure that it is flush
with the outside edge of the lift shaft.
NOTE: When the linkage is set correctly, the dampener's
intermediate and oscillator rollers will separate when the
single lever is returned to the "OFF" position.
14
15
Install the new water form roller (X07-0135) provided by Accel. Use
the original form roller shaft. Check the end play of the roller in the
night latch position and adjust if necessary.
Replace both of the inker guards with the new ones provided by
Accel (X18-0132).
YOU ARE NOW READY TO MAKE THE FINAL ADJUSTMENTS
25
26
FINAL ADJUSTMENTS
1
2
M
P
I
O
(4 mm)
5/32"
F
INK UP THE DAMPENER
Make sure the dampener is in the "OFF" position. Apply a small
amount of ink on the dampener oscillator roller only. Turn on the
press and run for 30-40 seconds and allow the ink to mill. Only the
oscillator and form roller will ink up at this time.
OSCILLATOR TO FORM ROLLER PRESSURE
After the press sits still for 15-20 seconds, jog the press forward
slightly while looking at the form roller. A stripe or bead line should
appear on the form roller which was created by the oscillator. This
stripe should be 5/32" (4mm) wide. To adjust, turn the long slotted
screw (subject arrow) clockwise to increase the stripe at both OPS
& NOPS. Refer to the Ryobi manual for this adjustment if necessary
as it is the same as the original dampener.
Plate
Cylinder
3
M
I
P
FORM ROLLER TO PLATE CYLINDER PRESSURE
Drop the dampener form roller down to the plate and back to "OFF"
again. This will leave a stripe on the plate which should be 5/32"
(4mm). This stripe is adjusted exactly as the original dampener by
turning the adjustment knobs. To increase pressure at both OPS
and NOPS, turn the adjustment knobs counterclockwise.
O
F
(4 mm)
5/32"
Plate
Cylinder
27
28
FINAL ADJUSTMENTS
4
M
P
I
O
(4 mm)
5/32"
F
Plate
Cylinder
5
M
P
I
O
(3.5mm)
F
INTERMEDIATE TO OSCILLATOR ROLLER PRESSURE
Temporarily remover the dampener metering roller by removing the
lower cap head bolts and remove the cap on the metering roller
retaining bracket. Drop the dampener down to the plate cylinder
and back off. In addition to the form roller contacting the plate, the
intermediate roller will drop down and contact the oscillator roller.,
Turn the intermediate roller around by hand to reveal the stripe
which should be 5/32" (4mm). This pressure is adjusted by turning
the set screw on the dampener frame. Turning the set screws down
will decrease the stripe and vice versa. Tighten the lock nut after the
proper stripe is obtained.
METERING TO INTERMEDIATE PRESSURE
Replace the dampener metering roller and fully tighten the cap
head bolt on the retaining bracket. Now you can ink up the entire
dampener and run in the ink until it is smooth. The proper pressure
between these rollers is 3.5 mm. Adjustments are made by loosening the lock nut on top of the metering roller hanger and turning the
set screw clockwise to increase the stripe and vice-versa. Tighten
the lock nut once the proper stripe is obtained.
NOTE: In order to observe the stripe, it may be necessary to
place the single lever in the "WATER ON" position and jog the
press in reverse. You will then be able to observe the stripe on
the metering roller.
Plate
Cylinder
6
M
I
P
O
F
(4.5 mm)
3/16"
MAXIMUM METERING TO PAN ROLLER PRESSURE
Turn the press on and run for 30-40 seconds to mill in the ink. Stop
the press and allow it to sit still for 15-20 seconds. Jog the press
forward and observe the stripe on the pan roller. It should be 3/16"
(4.5mm). Turn the knurled metering knobs clockwise to increase
the stripe and vice versa. When the proper stripe has been
obtained, spin the rachet gears down until they bottom out on the
stud and secure the rachet gear to the knurled knobs with set
screws.
Plate
Cylinder
29
30
FINAL ADJUSTMENTS
7
8
WATER LEVEL IN PAN
Install the water pan and bottle. Set the water level in the pan by
adjusting the bottle bracket. Raising the bracket will raise the pan
level and vice versa. Water should be about half way up the pan.
Reinstall the covers on the press.
YOU ARE NOW READY TO PRINT.
31
BASIC OPERATION
START OF DAY
A.
Make sure the form and metering rollers are in place.
B.
Spin knurled knobs until the shoulder on the ratchet
stops against the stud bar.
C.
Mount plate to cylinder. Wipe down all plates before
running. Pre-ink the Crestline® AltraTM Series dampener
before running the plates with an extremely light
coverage of ink. Dab the ink on the oscillator only.
D.
Place water bottle in bracket.
NOTE: Accel recommends using the proper fountain
solution for the plate material being run on the press. A
good acid/gum etch should be used with metal plates.
RUNNING
DURING THE DAY
32
A.
In general, the Crestline® AltraTM Series dampener should
not have to be adjusted from job to job. The form roller
setting should never be changed unless it has deviated
from thefactory specification of 5/32" to the plate.
B.
Adjustments to the amount of water fed to the plate are
made by the knurled knobs that apply pressure to the
metering roller. The dampener has been set up for
minimum water. To increase the water to the plate, turn
the knurled knobs counter clockwise 1 or 2 clicks at a
time. This opens the gap between the metering and pan
rollers and allows more water to the plate.
C.
In general, more water will only be required when going
from a metal plate to an electrostatic or Silvermaster type
plate.
CLEANING & MAINTENANCE
WASH UPS
DURING THE DAY
END OF THE DAY
1.
Remove bottle and drain the excess water from the pan.
2.
Mount a metal plate to the press.
3.
Turn on the press and squirt a small amount of press
wash on the ink rollers.
4.
Drop both the dampener and ink forms to the plate. In
general, the dampener will pick up enough roller wash off
the plate to clean itself. Apply wash directly to the dampener only when necessary.
5.
Use wash up attachment as normal. The plate cylinder
is being used as a bridge between the dampener and
inker. Solution transfers from the dampener to the plate,
plate to inker, and inker to wash up attachment.
6.
Remove water pan and clean any solution left in it.
7.
Be sure to wipe excess clean up solution from the ends
of the dampener metering and pan rollers.
1.
Wash up dampener. Pay close attention to cleaning the
ends of the pan and metering rollers that extend past the
form rollers.
2.
Spin the knurled knobs up 2 full turns.
33
CLEANING & MAINTENANCE
DEGLAZING
THE DAMPENER
OILING AND
GREASING THE
DAMPENER
34
Periodic deglazing of water-soluble contaminants will be
necessary with the Crestline® AltraTM Series. Typically, once
every 2-3 weeks will be sufficient, unless you are running
electrostatic plates on a daily basis whereas deglazing should
be performed weekly. A 50/50 solution of household ammonia
and hot water can be used for deglazing purposes. If you prefer
a commercially available deglazer, avoid those containing
pumice or gritty substances. Always follow deglazing with
straight water and then roller wash. Accel offers a product
called COMPOUND X that we recommend for deglazing our
system. Contact your dealer or Accel for more information.
Place a small amount of grease on the gears once a
month.
CLEANING & MAINTENANCE
CRESTLINE® ALTRATM SERIES
CLEANING & MAINTENANCE CHART
Daily
Weekly
Bi-Weekly Monthly
Wash Rollers
Deglaze Rollers
Metal Plate Users
Silvermaster Plate Users
Electrostatic Plate Users
Grease Gears
Inspect Ball Bearings
Check Roller Pressures
Check Roller Surfaces
35
Parts Drawings
36
37
38
39
40
41
42
43
44
45
46
47
11103 Indian Trail, Dallas, TX 75229 Phone 972-484-6808, Fax 800-365-6510
E-Mail [email protected], Web Site www.accelgraphicsystems.com