X360Run1.1 (Slim+Trinity) Glitcher Board Instruction

X360Run1.1 (Slim+ Trinity) Glitcher Board Instruction
Ⅰ.The theory of X360Run Glitcher Board：
The X360Run send out a confirm width of pulse to XBOX360 slim
machine. For different type XBOX360 slim machine have different type
pulse time point and width.
Ⅱ.The X360Run Glitcher Board and trimming switch:
Ⅲ.Configuration and trimming description：
The user must choose a different configuration options according
to the different type XBOX360 slim machine.
The user can use the factory default setting of the X360Run
Glitcher board.the user can use the trimmability switch to get a
better time pulse,and this change will make XBOX360 machine achieve
the best effective.
Please choice default setting in the following three table，other
setting only for test by user choice。Please use “Corona Mode 1” for
Corona machine of Toshiba NandFlash on board and produced after Nov.
2013(need change the Windbond memory chip first)。
The Corona Mode2 for test by user choice。
The Compatible and function of Corona X360run Yellow-Board Mode
same as X360Run Yellow Board。
X360Run Glitcher board have four type switch and trimming
adjustable setting:
(S: short the jumper pad , O:open the jumper pad)
1. The XBOX360 slim machine type setting
Monolithic
XBOX360
Type
Timing
pulse
M2 M1 M0 capacitor
Corona
forward
S
S
Corona
default
S
Corona
Corona
Trinity10.83A
Trinity9.6A
Corona
Corona
Add-ons
delay
default
default
default
Add-ons
delay
default
Ceramics
Command
capacitors
CD
CO
S
330P
15P
S
O
330P
15P
S
O
S
330P
15P
S
O
O
330P
15P
O
O
S
S
S
O
O
O
S
150P
220P
330P
20P
25P
15P
O
O
O
330P
15P
Corona
Mode 1
Corona
Mode 2
Compatible
X360Run
Yellow-Board
Mode
According to the different type XBOX360 machine , set the according
M0,M1,M2 jumper pad with S or O follow this table. The value of capacitors
about CD and CO must set correct too . the factory default value is Corona
Mode 1:SSO.
2. Pulse time delay trimming setting
Delay trimming
D2
O
O
O
O
D1
S
S
O
O
D0
S
O
S
O
unit
-3
-2
-1
default
S
S
S
+1
S
S
O
+2
S
S
O
O
S
O
+3
+4
Corona Mode 1;
Compatible X360Run
Yellow-Board Corona
Mode
Trinity 10.83A
Trinity 9.6A
Corona Mode 2
The pulse time can be adjust to forward(forth:-1~-3) or
backward(back:+1~+4) on the basis of the standard value.
According to the different type XBOX360 machine, set the
according D0,D1,D2 jumper pad with S or O follow this table. the
factory default value is Corona Mode 1/X360Run Yellow-Board Corona
Mode:SSS(+1).
3. Pulse width trimming setting
width trimming
Trinity 10.83A
Trinity 9.6A
Corona Mode 2
W2
O
O
O
W1
S
S
O
W0
S
O
S
unit
O
O
O
default
S
S
S
+1
S
S
O
+2
S
S
O
O
S
O
+3
+4
-3
-2
-1
Corona Mode 1;
Compatible X360Run
Yellow-Board Corona
Mode
The pulse width can be adjust to forward(forth:-1~-3) or backward
(back:+1~+4) on the basis of the standard value.
According to the different type XBOX360 machine, set the according
W0,W1,W2 jumper pad with S or O follow this table. the factory
default value is Corona Mode 1/X360Run Yellow-Board Corona
Mode:SSO(+2).
4. The adjustment of resistance and capacitance in the pulse signal output ：
The D pin of X360Run Glitcher board is pulse signal output, can
reduce the pulse signal strength by series resistance, the factory
default value is 8.2Ώ.
The D pin of X360Run Glitcher board is pulse signal output, can
produce an effect on launch XBOX360 slim machine succeed by shunt-wound
differences value of Monolithic capacitance, the factory default value
is CD=330pf(Corona),CD=220pf(Trinity9.6A) or CD=150pf(Trinity10.83A)
The length of two pins about CD capacitance don’t cut to short
（The length of CD capacitance about 1.5cm-1.7cm）.
Attention!: if replace Monolithic capacitance,must weld the new
Monolithic capacitance complete before launch XBOX360 slim machine
again.
5.Wire Install：
X360Run Glitcher board have SIX wire to be connected，them are:
1.
2.
3.
4.
5.
6.
Power Wire: VDD,
Ground Wire: GND,
I2C_SCL(E),
I2C_SDA(F),
POST_OUT(C),
CPU_RST(D)
①For Corona and Trinity 9.6A：
The 1—4 Wire direct connect to Glitcher board，about 10cm．
The 5-6 Wire direct connect to Glitcher board，about 4cm to 7cm.can
adjustment the length of 5-6 Wire in 4cm to 7cm carefully,then get the
best effect.
②For Trinity 10.83A：
The 1—4 Wire direct connect to Glitcher board，about 10cm．
The 5 Wire direct connect to Glitcher board ， about 4cm to 7cm.can
adjustment the length of 5 Wire in 4cm to 7cm carefully,then get the
best effect.
The 6 Wire direct connect to Glitcher board，about 4cm to 15cm(12cm is
typical value).can adjustment the length of 6 Wire in 4cm to 15cm
carefully,then get the best effect.
Attention!:
After modify the Xbox360 Trinity 10.83A machine,Must open and close
10 times to 20 times to check Whether or not Red-led on panel is Lights
up.if Red-led is Lights up,Can connect D point to GND point on X360Run
PCB Board with a 10K-20K metal-wire Resistor.
Ⅳ.The weld of changed XBOX360 slim machine
1. Corona-V1, Corona-V2
2. Corona-V3, Corona-V4，Corona-V5，Corona-V6
3.Trinity
Ⅴ. Debug and install
GND
3.3V
CPU_C
CPU_E
CPU_F
CPU_D
CO
CD
C1
C2
“CPU_C”to“C” wire
“CPU_D”to“D” wire
；
；
The shunt-wound Monolithic capacitance CD [330pf(Corona) or
220pf(Trinity)],one pin weld to C1 point, another pin weld to a point
between D point and C2 point.
The length of two pins about CD capacitance don’t cut to short.
Ⅵ. Typical application
Corona Mode 1，be fit for Corona（Include the Xbox360 machine produced
after Nov. 2013 and Corona machine of Toshiba NandFlash on board）
XBOX360
Timing
M2
M1
M0
Type
pulse
Corona
default
S
S
O
Delay
D2
D1
D0
unit
trimming
S
S
S
+1
width
trimming
W2
W1
W0
S
S
O
unit
+2
Attention!:
The Xbox360 machine of Windbond memory on board， produced after Nov.
2013,need change the Windbond memory chip first.
Corona Mode 2，be fit for Corona（for test by user choice）
XBOX360
Timing
M2
M1
M0
Type
pulse
Corona
default
S
O
O
Delay
D2
D1
D0
unit
trimming
S
O
S
+3
width
trimming
W2
W1
W0
unit
O
O
O
default
Attention!:
The Xbox360 machine of Windbond memory on board， produced after Nov.
2013,need change the Windbond memory chip first.
Compatible X360Run Yellow-Board Corona Mode ，be fit for Corona（Not
include the Xbox360 machine of Toshiba NandFlash on board and Corona of
change the Windbond memory chip first.）
XBOX360
Timing
M2
M1
M0
Type
pulse
Corona
default
O
O
O
Delay
D2
D1
D0
unit
trimming
S
S
S
+1
width
trimming
W2
W1
W0
S
S
O
unit
+2